library ieee; use ieee.std_logic_1164.all; use ieee.numeric_std.all; library work; use work.decode_types.all; use work.common.all; -- 2 cycle LSU -- We calculate the address in the first cycle entity loadstore1 is port ( clk : in std_ulogic; rst : in std_ulogic; l_in : in Execute1ToLoadstore1Type; e_out : out Loadstore1ToExecute1Type; l_out : out Loadstore1ToWritebackType; d_out : out Loadstore1ToDcacheType; d_in : in DcacheToLoadstore1Type; m_out : out Loadstore1ToMmuType; m_in : in MmuToLoadstore1Type; dc_stall : in std_ulogic; log_out : out std_ulogic_vector(9 downto 0) ); end loadstore1; -- Note, we don't currently use the stall output from the dcache because -- we know it can take two requests without stalling when idle, we are -- its only user, and we know it never stalls when idle. architecture behave of loadstore1 is -- State machine for unaligned loads/stores type state_t is (IDLE, -- ready for instruction SECOND_REQ, -- send 2nd request of unaligned xfer ACK_WAIT, -- waiting for ack from dcache LD_UPDATE, -- writing rA with computed addr on load MMU_LOOKUP, -- waiting for MMU to look up translation TLBIE_WAIT, -- waiting for MMU to finish doing a tlbie SPR_CMPLT -- complete a mf/tspr operation ); type reg_stage_t is record -- latch most of the input request load : std_ulogic; tlbie : std_ulogic; dcbz : std_ulogic; mfspr : std_ulogic; addr : std_ulogic_vector(63 downto 0); store_data : std_ulogic_vector(63 downto 0); load_data : std_ulogic_vector(63 downto 0); write_reg : gpr_index_t; length : std_ulogic_vector(3 downto 0); byte_reverse : std_ulogic; sign_extend : std_ulogic; update : std_ulogic; update_reg : gpr_index_t; xerc : xer_common_t; reserve : std_ulogic; rc : std_ulogic; nc : std_ulogic; -- non-cacheable access virt_mode : std_ulogic; priv_mode : std_ulogic; state : state_t; dwords_done : std_ulogic; first_bytes : std_ulogic_vector(7 downto 0); second_bytes : std_ulogic_vector(7 downto 0); dar : std_ulogic_vector(63 downto 0); dsisr : std_ulogic_vector(31 downto 0); instr_fault : std_ulogic; sprval : std_ulogic_vector(63 downto 0); end record; type byte_sel_t is array(0 to 7) of std_ulogic; subtype byte_trim_t is std_ulogic_vector(1 downto 0); type trim_ctl_t is array(0 to 7) of byte_trim_t; signal r, rin : reg_stage_t; signal lsu_sum : std_ulogic_vector(63 downto 0); signal log_data : std_ulogic_vector(9 downto 0); -- Generate byte enables from sizes function length_to_sel(length : in std_logic_vector(3 downto 0)) return std_ulogic_vector is begin case length is when "0001" => return "00000001"; when "0010" => return "00000011"; when "0100" => return "00001111"; when "1000" => return "11111111"; when others => return "00000000"; end case; end function length_to_sel; -- Calculate byte enables -- This returns 16 bits, giving the select signals for two transfers, -- to account for unaligned loads or stores function xfer_data_sel(size : in std_logic_vector(3 downto 0); address : in std_logic_vector(2 downto 0)) return std_ulogic_vector is variable longsel : std_ulogic_vector(15 downto 0); begin longsel := "00000000" & length_to_sel(size); return std_ulogic_vector(shift_left(unsigned(longsel), to_integer(unsigned(address)))); end function xfer_data_sel; begin -- Calculate the address in the first cycle lsu_sum <= std_ulogic_vector(unsigned(l_in.addr1) + unsigned(l_in.addr2)) when l_in.valid = '1' else (others => '0'); loadstore1_0: process(clk) begin if rising_edge(clk) then if rst = '1' then r.state <= IDLE; else r <= rin; end if; end if; end process; loadstore1_1: process(all) variable v : reg_stage_t; variable brev_lenm1 : unsigned(2 downto 0); variable byte_offset : unsigned(2 downto 0); variable j : integer; variable k : unsigned(2 downto 0); variable kk : unsigned(3 downto 0); variable long_sel : std_ulogic_vector(15 downto 0); variable byte_sel : std_ulogic_vector(7 downto 0); variable req : std_ulogic; variable busy : std_ulogic; variable addr : std_ulogic_vector(63 downto 0); variable wdata : std_ulogic_vector(63 downto 0); variable write_enable : std_ulogic; variable do_update : std_ulogic; variable two_dwords : std_ulogic; variable done : std_ulogic; variable data_permuted : std_ulogic_vector(63 downto 0); variable data_trimmed : std_ulogic_vector(63 downto 0); variable use_second : byte_sel_t; variable trim_ctl : trim_ctl_t; variable negative : std_ulogic; variable sprn : std_ulogic_vector(9 downto 0); variable exception : std_ulogic; variable next_addr : std_ulogic_vector(63 downto 0); variable mmureq : std_ulogic; variable dsisr : std_ulogic_vector(31 downto 0); variable mmu_mtspr : std_ulogic; variable itlb_fault : std_ulogic; begin v := r; req := '0'; byte_sel := (others => '0'); addr := lsu_sum; v.mfspr := '0'; mmu_mtspr := '0'; itlb_fault := '0'; sprn := std_ulogic_vector(to_unsigned(decode_spr_num(l_in.insn), 10)); dsisr := (others => '0'); mmureq := '0'; write_enable := '0'; do_update := '0'; two_dwords := or (r.second_bytes); -- load data formatting byte_offset := unsigned(r.addr(2 downto 0)); brev_lenm1 := "000"; if r.byte_reverse = '1' then brev_lenm1 := unsigned(r.length(2 downto 0)) - 1; end if; -- shift and byte-reverse data bytes for i in 0 to 7 loop kk := ('0' & (to_unsigned(i, 3) xor brev_lenm1)) + ('0' & byte_offset); use_second(i) := kk(3); j := to_integer(kk(2 downto 0)) * 8; data_permuted(i * 8 + 7 downto i * 8) := d_in.data(j + 7 downto j); end loop; -- Work out the sign bit for sign extension. -- Assumes we are not doing both sign extension and byte reversal, -- in that for unaligned loads crossing two dwords we end up -- using a bit from the second dword, whereas for a byte-reversed -- (i.e. big-endian) load the sign bit would be in the first dword. negative := (r.length(3) and data_permuted(63)) or (r.length(2) and data_permuted(31)) or (r.length(1) and data_permuted(15)) or (r.length(0) and data_permuted(7)); -- trim and sign-extend for i in 0 to 7 loop if i < to_integer(unsigned(r.length)) then if two_dwords = '1' then trim_ctl(i) := '1' & not use_second(i); else trim_ctl(i) := not use_second(i) & '0'; end if; else trim_ctl(i) := '0' & (negative and r.sign_extend); end if; case trim_ctl(i) is when "11" => data_trimmed(i * 8 + 7 downto i * 8) := r.load_data(i * 8 + 7 downto i * 8); when "10" => data_trimmed(i * 8 + 7 downto i * 8) := data_permuted(i * 8 + 7 downto i * 8); when "01" => data_trimmed(i * 8 + 7 downto i * 8) := x"FF"; when others => data_trimmed(i * 8 + 7 downto i * 8) := x"00"; end case; end loop; -- compute (addr + 8) & ~7 for the second doubleword when unaligned next_addr := std_ulogic_vector(unsigned(r.addr(63 downto 3)) + 1) & "000"; done := '0'; exception := '0'; case r.state is when IDLE => when SECOND_REQ => addr := next_addr; byte_sel := r.second_bytes; req := '1'; v.state := ACK_WAIT; when ACK_WAIT => if d_in.valid = '1' then if d_in.error = '1' then -- dcache will discard the second request if it -- gets an error on the 1st of two requests if r.dwords_done = '1' then addr := next_addr; else addr := r.addr; end if; if d_in.cache_paradox = '1' then -- signal an interrupt straight away exception := '1'; dsisr(63 - 38) := not r.load; -- XXX there is no architected bit for this dsisr(63 - 35) := d_in.cache_paradox; v.state := IDLE; else -- Look up the translation for TLB miss -- and also for permission error and RC error -- in case the PTE has been updated. mmureq := '1'; v.state := MMU_LOOKUP; end if; else if two_dwords = '1' and r.dwords_done = '0' then v.dwords_done := '1'; if r.load = '1' then v.load_data := data_permuted; end if; else write_enable := r.load; if r.load = '1' and r.update = '1' then -- loads with rA update need an extra cycle v.state := LD_UPDATE; else -- stores write back rA update in this cycle do_update := r.update; done := '1'; v.state := IDLE; end if; end if; end if; end if; when MMU_LOOKUP => if r.dwords_done = '1' then addr := next_addr; byte_sel := r.second_bytes; else addr := r.addr; byte_sel := r.first_bytes; end if; if m_in.done = '1' then if m_in.invalid = '0' and m_in.perm_error = '0' and m_in.rc_error = '0' and m_in.badtree = '0' and m_in.segerr = '0' then if r.instr_fault = '0' then -- retry the request now that the MMU has installed a TLB entry req := '1'; if two_dwords = '1' and r.dwords_done = '0' then v.state := SECOND_REQ; else v.state := ACK_WAIT; end if; else -- nothing to do, the icache retries automatically done := '1'; v.state := IDLE; end if; else exception := '1'; dsisr(63 - 33) := m_in.invalid; dsisr(63 - 36) := m_in.perm_error; dsisr(63 - 38) := not r.load; dsisr(63 - 44) := m_in.badtree; dsisr(63 - 45) := m_in.rc_error; v.state := IDLE; end if; end if; when TLBIE_WAIT => if m_in.done = '1' then -- tlbie is finished done := '1'; v.state := IDLE; end if; when LD_UPDATE => do_update := '1'; v.state := IDLE; done := '1'; when SPR_CMPLT => done := '1'; v.state := IDLE; end case; busy := '1'; if r.state = IDLE or done = '1' then busy := '0'; end if; -- Note that l_in.valid is gated with busy inside execute1 if l_in.valid = '1' then v.addr := lsu_sum; v.load := '0'; v.dcbz := '0'; v.tlbie := '0'; v.instr_fault := '0'; v.dwords_done := '0'; v.write_reg := l_in.write_reg; v.length := l_in.length; v.byte_reverse := l_in.byte_reverse; v.sign_extend := l_in.sign_extend; v.update := l_in.update; v.update_reg := l_in.update_reg; v.xerc := l_in.xerc; v.reserve := l_in.reserve; v.rc := l_in.rc; v.nc := l_in.ci; v.virt_mode := l_in.virt_mode; v.priv_mode := l_in.priv_mode; -- XXX Temporary hack. Mark the op as non-cachable if the address -- is the form 0xc------- for a real-mode access. if lsu_sum(31 downto 28) = "1100" and l_in.virt_mode = '0' then v.nc := '1'; end if; -- Do length_to_sel and work out if we are doing 2 dwords long_sel := xfer_data_sel(l_in.length, v.addr(2 downto 0)); byte_sel := long_sel(7 downto 0); v.first_bytes := byte_sel; v.second_bytes := long_sel(15 downto 8); -- Do byte reversing and rotating for stores in the first cycle byte_offset := unsigned(lsu_sum(2 downto 0)); brev_lenm1 := "000"; if l_in.byte_reverse = '1' then brev_lenm1 := unsigned(l_in.length(2 downto 0)) - 1; end if; for i in 0 to 7 loop k := (to_unsigned(i, 3) xor brev_lenm1) + byte_offset; j := to_integer(k) * 8; v.store_data(j + 7 downto j) := l_in.data(i * 8 + 7 downto i * 8); end loop; case l_in.op is when OP_STORE => req := '1'; when OP_LOAD => req := '1'; v.load := '1'; when OP_DCBZ => req := '1'; v.dcbz := '1'; when OP_TLBIE => mmureq := '1'; v.tlbie := '1'; v.state := TLBIE_WAIT; when OP_MFSPR => v.mfspr := '1'; -- partial decode on SPR number should be adequate given -- the restricted set that get sent down this path if sprn(9) = '0' and sprn(5) = '0' then if sprn(0) = '0' then v.sprval := x"00000000" & r.dsisr; else v.sprval := r.dar; end if; else -- reading one of the SPRs in the MMU v.sprval := m_in.sprval; end if; v.state := SPR_CMPLT; when OP_MTSPR => if sprn(9) = '0' and sprn(5) = '0' then if sprn(0) = '0' then v.dsisr := l_in.data(31 downto 0); else v.dar := l_in.data; end if; v.state := SPR_CMPLT; else -- writing one of the SPRs in the MMU mmu_mtspr := '1'; v.state := TLBIE_WAIT; end if; when OP_FETCH_FAILED => -- send it to the MMU to do the radix walk addr := l_in.nia; v.addr := l_in.nia; v.instr_fault := '1'; mmureq := '1'; v.state := MMU_LOOKUP; when others => assert false report "unknown op sent to loadstore1"; end case; if req = '1' then if long_sel(15 downto 8) = "00000000" then v.state := ACK_WAIT; else v.state := SECOND_REQ; end if; end if; end if; -- Update outputs to dcache d_out.valid <= req; d_out.load <= v.load; d_out.dcbz <= v.dcbz; d_out.nc <= v.nc; d_out.reserve <= v.reserve; d_out.addr <= addr; d_out.data <= v.store_data; d_out.byte_sel <= byte_sel; d_out.virt_mode <= v.virt_mode; d_out.priv_mode <= v.priv_mode; -- Update outputs to MMU m_out.valid <= mmureq; m_out.iside <= v.instr_fault; m_out.load <= r.load; m_out.priv <= r.priv_mode; m_out.tlbie <= v.tlbie; m_out.mtspr <= mmu_mtspr; m_out.sprn <= sprn; m_out.addr <= addr; m_out.slbia <= l_in.insn(7); m_out.rs <= l_in.data; -- Update outputs to writeback -- Multiplex either cache data to the destination GPR or -- the address for the rA update. l_out.valid <= done; if r.mfspr = '1' then l_out.write_enable <= '1'; l_out.write_reg <= r.write_reg; l_out.write_data <= r.sprval; elsif do_update = '1' then l_out.write_enable <= '1'; l_out.write_reg <= r.update_reg; l_out.write_data <= r.addr; else l_out.write_enable <= write_enable; l_out.write_reg <= r.write_reg; l_out.write_data <= data_trimmed; end if; l_out.xerc <= r.xerc; l_out.rc <= r.rc and done; l_out.store_done <= d_in.store_done; -- update exception info back to execute1 e_out.busy <= busy; e_out.exception <= exception; e_out.instr_fault <= r.instr_fault; e_out.invalid <= m_in.invalid; e_out.badtree <= m_in.badtree; e_out.perm_error <= m_in.perm_error; e_out.rc_error <= m_in.rc_error; e_out.segment_fault <= m_in.segerr; if exception = '1' and r.instr_fault = '0' then v.dar := addr; if m_in.segerr = '0' then v.dsisr := dsisr; end if; end if; -- Update registers rin <= v; end process; ls1_log: process(clk) begin if rising_edge(clk) then log_data <= e_out.busy & e_out.exception & l_out.valid & m_out.valid & d_out.valid & m_in.done & r.dwords_done & std_ulogic_vector(to_unsigned(state_t'pos(r.state), 3)); end if; end process; log_out <= log_data; end;