commit ab490e8ff0a92e482352eb82296116989d2ccb24 Author: Jeff Scheel Date: Tue Aug 15 15:40:34 2017 -0500 Initial repo priming from IBM Internal tree. Signed-off-by: Jeff Scheel diff --git a/.gitignore b/.gitignore new file mode 100644 index 0000000..489e8f3 --- /dev/null +++ b/.gitignore @@ -0,0 +1,2 @@ +*~ +*target* diff --git a/DeviceTree/app_bibliography.xml b/DeviceTree/app_bibliography.xml new file mode 100644 index 0000000..bd1412b --- /dev/null +++ b/DeviceTree/app_bibliography.xml @@ -0,0 +1,284 @@ + + + + + Bibliography + This section lists documents which were referenced in this specification or which provide + additional information, and some useful information for obtaining these documents. Referenced + documents are listed below. When any of the following standards are superseded by an approved + revision, the revision shall apply. + + + + + + Linux on Power Architecture Reference: Platform and Device Tree + + + + + + + Linux on Power Architecture Reference: Error Recovery and Logging + + + + + Linux on Power Architecture Reference: Virtualization + + + + + Linux on Power Architecture Reference: Runtime Abstraction Services (RTAS) + + + + + Power ISA + + + + + IEEE 1275, IEEE Standard for Boot (Initialization Configuration) Firmware: + Core Requirements and Practices + IEEE part number DS02683, ISBN 1-55937-426-8 + + + + + Core Errata, IEEE P1275.7/D4 + + + + + Open Firmware Recommended Practice:OBP-TFTP + Extension + + + + + Open Firmware Recommended Practice: Device + Support Extensions + + + + + PCI Bus binding to: IEEE Std 1275-1994, Standard + for Boot (Initialization, Configuration) Firmware + + + + + Open Firmware: Recommended Practice - Interrupt + Mapping + + + + + Open Firmware: Recommended Practice - Forth Source + and FCode Image Support, Version 1.0 + + + + + Open Firmware: Recommended Practice - Interrupt + Mapping, Version 1.0 + + + + + Open Firmware: Recommended Practice - TFTP Booting + Extensions, Version 0.8 + + + + + Open Firmware: Recommended Practice - + Interposition, Version 0.2 + + + + + MS-DOS Programmer's Reference + Published by Microsoft + + + + + Peering Inside the PE: A Tour of the Win32 Portable + Executable File Format + Found in the March, 1994 issue of Microsoft Systems Journal + + + + + ISO-9660, Information processing -- Volume and + file structure of CD-ROM for information interchange + Published by International Organization for Standardization + + + + + System V Application Binary Interface, PowerPC + Processor Supplement + By Sunsoft + + + + + ISO Standard 8879:1986, Information Processing + -- Text and Office Systems -- Standard Generalized Markup Language (SGML) + + + + + IEEE 996, A Standard for an Extended Personal Computer + Back Plane Bus + + + + + PCI Local Bus Specification + All designers are responsible for assuring that they use the most current version of this document + at the time that they design conventional PCI related components or platforms. See the PCI SIG website + for the most current version of this document. + + + + + PCI-to-PCI Bridge Architecture Specification + All designers are responsible for assuring that they use the most current version of this document + at the time that they design conventional PCI related components or platforms. See the + PCI SIG website for the most current version of this document. + + + + + PCI Standard Hot-Plug Controller and Subsystem + Specification + + + + + PCI-X Protocol Addendum to the PCI Local Bus Specification + All designers are responsible for assuring that they use the most current version of this document at + the time that they design PCI-X related components or platforms. See the PCI SIG website for the most + current version of this document. + + + + + PCI Express Base Specification + All designers are responsible for assuring that they use the most current version of this document + at the time that they design PCI Express related components or platforms. See the PCI SIG website for + the most current version of this document. + + + + + PCI Express to PCI/PCI-X Bridge Specification + All designers are responsible for assuring that they use the most current version of this document at the + time that they design PCI Express related components or platforms. See the PCI SIG website for the most current + version of this document. + + + + + System Management BIOS (SMBIOS) Reference + Specification + + + + + (List Number Reserved for Compatibility) + + + + (List Number Reserved for Compatibility) + + + + (List Number Reserved for Compatibility) + + + + + IBM RS/6000® Division, Product Topology Data System, + Product Development Guide + Version 2.1 + + + + + Single Root I/O Virtualization and Sharing Specification + All designers are responsible for assuring that they use the most current version of this document at + the time that they design PCI Express SR-IOV related components or platforms. See the PCI SIG website + for the most current version of this document. + + + + + Multi-Root I/O Virtualization and Sharing Specification + All designers are responsible for assuring that they use the most current version of this document at the + time that they design PCI Express MR-IOV related components or platforms. See the PCI SIG website for the + most current version of this document. + + + + + + diff --git a/DeviceTree/app_glossary.xml b/DeviceTree/app_glossary.xml new file mode 100644 index 0000000..acd25d0 --- /dev/null +++ b/DeviceTree/app_glossary.xml @@ -0,0 +1,1290 @@ + + + + + Glossary + This glossary contains an alphabetical list of terms, phrases, and abbreviations used in this document. + + + + Term + Definition + + + + AC + Alternating current + + + + ACR + Architecture Change Request + + + + AD + Address Data line + + + + Adapter + A device which attaches a device to a bus or which converts one + bus to another; for example, an I/O Adapter (IOA), a PCI Host Bridge (PHB), + or a NUMA fabric attachment device. + + + + + addr + Address + + + + Architecture + The hardware/software interface definition or software module to + software module interface definition. + + + + ASCII + American National Standards Code for Information + Interchange + + + + ASR + Address Space Register + + + + BAT + Block Address Translation + + + + BE + Big-Endian or Branch Trace Enable bit in the + MSR (MSRBE) + + + + BIO + Bottom of Peripheral Input/Output Space + + + + BIOS + Basic Input/Output system + + + + BIST + Built in Self Test + + + + Boundedly undefined + Describes some addresses and registers which when referenced provide + one of a small set of predefined results. + + + + BPA + Bulk Power Assembly. Refers to components used for power distribution + from a central point in the rack. + + + + BPM + Bottom of Peripheral Memory + + + + BSCA + Bottom of System Control Area + + + + BSM + Bottom of System Memory + + + + BUID + Bus Unit Identifier. The high-order part of an interrupt source number + which is used for hardware routing purposes by the platform. + + + + CCIN + Custom Card Identification Number + + + + CD-ROM + Compact Disk Read-Only Memory + + + + CIS + Client Interface Service + + + + CMO + Cooperative Memory Over-commitment option. See + for more information. + + + + + + CMOS + Complimentary Metal Oxide Semiconductor + + + + Conventional PCI + Behavior or features that conform to . + + + + CPU + Central Processing Unit + + + + CR + Condition Register + + + + CTR + Count Register + + + + DABR + Data Address Breakpoint Register + + + + DAR + Data Address Register + + + + DASD + Direct Access Storage Device (a synonym for “hard disk”) + + + + DBAT + Data Block Address Translation + + + + DC + Direct current + + + + DEC + Decrementer + + + + DIMM + Dual In-line Memory Module + + + + DMA + Direct Memory Access + + + + DMA Read + A data transfer from System Memory to I/O. A DMA Read Request + is the inbound operation and the DMA Read Reply (or Read Completion) is the + outbound data coming back from a DMA Read Request. + + + + DMA Write + A data transfer to System Memory from I/O or a Message Signalled Interrupt (MSI) DMA Write. This is an inbound operation. + + + + DOS + Disk OS + + + + DR + Data Relocate bit in MSR (MSRDR) + + + + DRA + Deviation Risk Assessment + + + + DRAM + Dynamic Random Access Memory + + + + DRC + Delayed Read Completion. A transaction that has completed + on the destination bus and is now moving toward the originating bus to complete. + DR Connector. + + + + DR entity + An entity that can participate in DR operations. That is, an entity + that can be added or removed from the platform while the platform power is on and the + system remains operational. + + + + DRR + Delayed Read Request. A transaction that must complete on the destination bus before completing on the originating bus. + + + + DSISR + Data Storage Interrupt Status Register + + + + DWR + Delayed Write Request. A transaction that must complete on the destination bus before completing on the originating bus. + + + + EA + Effective Address + + + + EAR + External Access Register + + + + ECC + Error Checking and Correction + + + + EE + External interrupt Enable bit in the MSR (MSREE) + + + + EEH + Enhance I/O Error Handling + + + + EEPROM + Electrically Erasable Programmable Read Only Memory + + + + EPOW + Environment and Power Warning + + + + + Error Log indicator An amber indicator that indicates that the user needs to + look at the error log or problem determination procedures, in order to determine the cause. + Previously called System Information (Attention). + + + + FCode + A computer programming language defined by the OF standard which is semantically + similar to the Forth programming language, but is encoded as a sequence of binary byte codes + representing a defined set of Forth words. + + + + FE0 + Floating-point Exception mode 0 bit in the MSR (MSRFE0) + + + + FE1 + Floating-point Exception mode 1bit in the MSR (MSRFE1) + + + + FIR + Fault Isolation Registers + + + + FLR + Function Level Reset (see PCI Express documentation). An optional reset for PCI Express + functions that allows resetting a single function of a multi-function IOA. + + + + FP + Floating-Point available bit in the MSR (MSRFP) + + + + FPSCR + Floating-Point Status And Control Register + + + + FRU + Field Replaceable Unit + + + + FSM + Finite State Machine + + + + GB + Gigabytes - as used in this document it is 2 raised to the power of 30 + + + + HB + Host Bridge + + + + HMC + Hardware Management Console - used generically to refer to the system + component that performs platform administration function where ever physically located. + The HMC is outside of this architecture and may be implemented in multiple ways. + Examples include: a special HMC applications in another system, an external appliance, + or in an LPAR partition using the Virtual Management Channel (VMC) interface to the + hypervisor. + + + + Hz + Hertz + + + + IBAT + Instruction block address translation + + + + ID + Identification + + + + IDE + Integrated Device Electronics + + + + IDU + Interrupt Delivery Unit + + + + IEEE + Institute of Electrical and Electronics Engineers + + + + I2C + Inter Integrated-circuit Communications + + + + I/O + nput/Output + + + + I/O bus master + Any entity other than a processor, cache, + memory controller, or host bridge which supplies both address and data in + write transactions or supplies the address and is the sink for the data in + read transactions. + + + + I/O device + Generally refers to any entity that is connected + to an IOA (usually through a cable), but in some cases may refer to the IOA + itself (that is, a device in the device tree that happens to be used for I/O + operations). + + + + I/O Drawer + An enclosure in a rack that holds at least one PHB and at + least one IOA. + + + + ILE + Interrupt Little-Endian bit in MSR (MSRILE) + + + + Instr + Instruction + + + + Interrupt Number + See Interrupt Vector below. + + + + Interrupt Vector + The identifier associated with a specific interrupt source. + The identifier’s value is loaded into the source’s Interrupt Vector Register and + is read from the Interrupt Delivery Unit’s Interrupt Acknowledge Register. + + + + IOA + I/O Adapter. A device which attaches to a physical bus which is capable + of supporting I/O (a physical IOA) or logical bus (a virtual IOA). The term “IOA” + without the usage of the qualifier “physical” or “virtual” will be + used to designate a physical IOA. Virtual IOAs are defined further in + + . + In PCI terms, an IOA may be defined by a unique combination of its assigned + bus number and device number, but not necessarily including its function number. + That is, an IOA may be a single or multi-function device, unless otherwise specified by + the context of the text. In the context of a PCIe I/O Virtualized (IOV) device (not to be + confused with a virtual IOA), an IOA is a single or multiple function device (for example, a + PCIe Virtual Function (VF) or multiple VFs). An IOA function may or may not have its own set of + resources, that is may or may not be in its own Partitionable Endpoint (PE) domain + (see also + + ). + + + + + IOA function + That part of an IOA that deals with a specific part of the + IOA as defined by the configuration space “Function” part of Bus/Device/Function. + For single-function IOAs, the IOA Function and the IOA are synonymous. + + + + IP + Interrupt Prefix bit in MSR (MSRIP) + + + + IPI + Interprocessor Interrupt + + + + IR + Instruction Relocate bit in MSR register (MSRIR) or infrared + + + + ISF + Interrupt 64-bit processor mode bit in the MSR (MSRISF) + + + + ISO + International Standards Organization + + + + ISR + Interrupt Source Register + + + + ISU + Interrupt Source Unit + + + + KB + Kilobytes - as used in this document it is 2 raised to the power of 10 + + + + KHz + Kilo Hertz + + + + LAN + Local Area Network + + + + LCD + Liquid Crystal Display + + + + LE + Little-Endian bit in MSR (MSRLE) or Little-Endian + + + + LED + Light Emitting Diode + + + + LMB + Logical Memory Block. The Block of logical memory addresses associated with a dynamically + reconfigurable memory node. + + + + Load + A Load Request is the outbound (from the processor) operation + and the Load Reply is the inbound data coming back from a + Load Request. When it relates to I/O operations, this is an + MMIO Load . + + + + LR + Link Register + + + + LSb + Least Significant bit + + + + LSB + Least Significant Byte + + + + LSI + Level Sensitive Interrupt + + + + LUN + Logical Unit Number + + + + L1 + Primary cache + + + + L2 + Secondary cache + + + + MB + Megabytes - as used in this document it is 2 raised to the power of 20 + + + + ME + Machine check Enable + + + + MMIO + Memory Mapped I/O. This refers to the mapping of the address space required + by an I/O device for Load or Store operations into + the system’s address space. + + + + MES + Miscellaneous Equipment Specification + + + + MFM + Modified frequency modulation + + + + MHz + Mega Hertz + + + + MOD + Address modification bit in the MSR + (MSRMOD) + + + + MP + Multiprocessor + + + + MSb + Most Significant bit + + + + MSB + Most Significant Byte + + + + MSI + Message Signalled Interrupt + + + + MSR + Machine State Register + + + + MTT + Multi-TCE-Table option. See + + + . + + + + + N/A + Not Applicable + + + + Nibble + Refers to the first or last four bits in an 8 bit byte + + + + NUMA + Non-Uniform Memory Access + + + + NUMA fabric + Mechanism and method for connecting the multiple nodes of a NUMA system + + + + NVRAM + Nonvolatile Random Access Memory + + + + OF + Open Firmware + + + + OP + Operator + + + + OS + Operating System + + + + OUI + Organizationally Unique Identifier + + + + PA + Processor Architecture + + + + PAP + Privileged Access Password + + + + LoPAR + Used within the Linux on Power Architecture + Reference documents to denote: (1) the architectural requirements specified + by the Linux on Power Architecture Reference document, (2) the Linux on Power Architecture + Reference documents themself, and (3) as an adjective to qualify an entity as being + related to this architecture. + + + + Partitionable Endpoint + This refers to the I/O granule that may be treated as one for + purposes of assignment to an OS (for example, to an LPAR partition). May be an + I/O adapter (IOA), or groups of IOAs and bridges, or portions of IOAs. PE granularity + supported by the hardware may be finer than is supported by the firmware. Grouping + of multiple PEs into one DR entity may limit assignment of a the separate PEs to different + LPAR partitions. See also DR entity. + + + + PC + Personal Computer + + + + PCI + Peripheral Component Interconnect. An all-encompassing term referring to + conventional PCI, PCI-X, and PCI Express. + + + + PCI bus + A general term referring to either the PCI Local Bus, as + specified in and + for conventional PCI and PCI-X, or a PCI Express link, as specified in + for PCI Express. + + + + PCI Express + Behavior or features that conform to + . + + + + PCI link + A PCI Express link, as specified in . + + + + PCI-X + Behavior or features that conform to . + + + + PD + Presence Detect + + + + PE + When referring to the body of the LoPAR, this refers to a Partitionable + Endpoint. + + + + + + + PEM + Partition Energy Management option. See + + + . + + + + + Peripheral I/O Space + The range of real addresses which are assigned + to the I/O Space of a Host Bridge (HB) and which are sufficient to contain all of + the Load and Store address space requirements of all the devices in the I/O Space + of the I/O bus that is generated by the HB. A keyboard controller is an example of + a device which may require Peripheral I/O Space addresses. + + + + Peripheral Memory Space + The range of real addresses which are assigned to the Memory + Space of a Host Bridge (HB) and which are sufficient to contain all of the Load and + Store address space requirements of the devices in the Memory Space of the I/O bus + that is generated by the HB. The frame buffer of a graphics adapter is an example + of a device which may require Peripheral Memory Space addresses. + + + + Peripheral Space + Refers to the physical address space which may + be accessed by a processor, but which is controlled by a host bridge. At least one + peripheral space must be present and it is referred to by the suffix 0. A host bridge + will typically provide access to at least a memory space and possibly to an I/O + space. + + + + PHB + PCI Host Bridge + + + + PIC + Programmable Interrupt Controller + + + + PIR + Processor Identification Register + + + + Platform + Refers to the hardware plus firmware portion of a system composed of hardware, + firmware, and OS. + + + + Platform firmware + Refers to all firmware on a system including the software or firmware in a + support processor. + + + + Plug-in I/O card + A card which can be plugged into an I/O + connector in a platform and which contains one or more IOAs and potentially + one or more I/O bridges or switches. + + + + Plug-in Card + An entity that plugs into a physical slot. + + + + PMW + Posted memory write. A transaction that has complete on the + originating bus before completing on the destination bus + + + + PnP + Plug and Play + + + + POP + Power On Password + + + + POST + Power-On Self Test + + + + PR + Privileged bit in the MSR (MSRPR) + + + + Processor Architecture + Used throughout this document to + mean compliance with the requirements specified in + . + + + + Processor revision number + A 16-bit number that distinguishes between various releases + of a particular processor version, for example different engineering change + levels. + + + + PVN + Processor Version Number. Uniquely determines the particular + processor and PA version. + + + + PVR + Processor Version Register. A register in each processor + that identifies its type. The contents of the PVR include the processor + version number and processor revision number. + + + + RAID + Redundant Array of Independent Disks + + + + RAM + Random Access Memory + + + + RAS + Reliability, Availability, and Serviceability + + + + Real address + A real address results from doing address + translation on an effective address when address translation is enabled. + If address translation is not enabled, the real address is the same as the + effective address. An attempt to fetch from, load from, or store to a real + address that is not physically present in the machine may result in a + machine check interrupt. + + + + Reserved + The term “reserved” is used within this + document to refer to bits in registers or areas in the address space + which should not be referenced by software except as described in this + document. + + + + Reserved for firmware use + Refers to a given location or bit which may not be used by + software, but are used by firmware. + + + + Reserved for future use + Refers to areas of address space or bits in registers which may be + used by future versions of this architecture. + + + + RI + Recoverable interrupt bit in the MSR (MSRRI) + + + + RISC + Reduced Instruction Set Computing + + + + RMA + Real Mode Area. The first block of logical memory addresses + owned by a logical partition, containing the storage that may be accessed with + translate off. + + + + ROM + Read Only Memory + + + + Root Complex + A PCI Express root complex as specified in + . + + + + RPN + Real Page Number + + + + RTAS + Run-Time Abstraction Services + + + + RTC + Real Time Clock + + + + SAE + Log Service Action Event log + + + + SCC + Serial Communications Controller + + + + SCSI + Small Computer System Interface + + + + SE + Single-step trace enabled bit in the MSR + (MSRSE) + + + + Service Focal Point + The common point of control in the system for handling all + service actions + + + + Serviceable Event + Serviceable Events are platform, + global, regional and local error events that require a service action + and possibly a call home when the serviceable event must be handled by a + service representative or at least reported to the service provider. + Activation of the Error Log indicator notifies the customer of the event + and the event indicates to the customer that there must be some intervention + to rectify the problem. The intervention may be a service action that the + customer can perform or it may require a service provider. + + + + SES + Storage Enclosure Services (can also mean SCSI Enclosure + Services in relation to SCSI storage) + + + + SF + Processor 32-bit or 64-bit processor mode bit in the MSR + (MSRSF) + + + + SFP + Service Focal Point + + + + Shrink-wrap OS + A single version of an OS that runs on all + compliant platforms. + + + + Shrink-wrap Application + A single version of an application program + that runs on all compliant platforms with the applicable OS. + + + + SMP + Symmetric multiprocessor + + + + SMS + System Management Services + + + + Snarf + An industry colloquialism for cache-to-cache + transfer. A typical scenario is as follows: (1) cache miss from cache A, + (2) line found modified in cache B, (3) cache B performs castout of modified + line, and (4) cache A allocates the modified line as it is being written back + to memory. + + + + Snoop + The act of interrogating a cache for the presence of a + line, usually in response to another party on a shared bus attempting to + allocate that line. + + + + SPRG + Special Purpose Registers for General use + + + + SR + System Registers + + + + SRC + Service Reference Code + + + + SRN + Service Request Number + + + + Store + A Store Request is an + outbound (from the processor) operation. When it relates to I/O + operations, this is an MMIO Store. + + + + System + Refers to the collection of hardware, system firmware, + and OS software which comprise a computer model. + + + + System address space + The total range of addressability as established by the + processor implementation. + + + + System Control Area + Refers to a range of addresses which + contains the system ROM(s) and an unarchitected, reserved, platform-dependent + area used by firmware and Run-Time Abstraction services for control of the + platform. The ROM areas are defined by the OF properties in the + openprom and os-rom nodes + of the OF device tree. + + + + System Information (Attention) indicator + See Error Log indicator. + + + + System firmware + Refers to the collection of all firmware on a system + including OF, RTAS and any legacy firmware. + + + + System Memory + Refers to those areas of memory which form + a coherency domain with respect to the PA processor or processors that + execute application software on a system. + + + + System software + Refers to the combination of OS software, + device driver software, and any hardware abstraction software, but + excludes the application software. + + + + TB + Time Base + + + + TCE + Translation Control Entry + + + + TLB + Translation Look-aside Buffer + + + + TOD + Time Of Day + + + + TOSM + Top of system memory + + + + TPM + Top of Peripheral Memory + Trusted Platform Module + + + + tty + Teletypewriter or ASCII character driven + terminal device + + + + UI + User Interface + + + + USB + Universal Serial Bus + + + + v + Volt + + + + VGA + Video Graphics Array + + + + VMC + Virtual Management Channel + + + + VPD + Vital Product Data + + + + VPNH + Virtual Processor Home Node option. See + + + . + + + + + + + + + + + + + + diff --git a/DeviceTree/bk_main.xml b/DeviceTree/bk_main.xml new file mode 100644 index 0000000..8238c3f --- /dev/null +++ b/DeviceTree/bk_main.xml @@ -0,0 +1,109 @@ + + + + + + + Device Tree Bindings + Linux on Power Architecture Reference + + + + + System Software Work Group + + syssw-chair@openpowerfoundation.org + + OpenPOWER Foundation + + + + 2016 + OpenPOWER Foundation + + + Revision 2.0_pre1 + OpenPOWER + + + + + + Copyright details are filled in by the template. + + + + + + The purpose of this document is to provide firmware and software + architectural details associated with Device Tree Bindings on OpenPOWER Systems. + The base content for this document were contributed to the OpenPOWER Foundation in the + IBM Linux on Power Architecture Platform Reference (LoPAPR) Draft + document. It had numerous contributors inside IBM. + This document is a Standard Track, Work Group Specification work product owned by the + System Software Workgroup and handled in compliance with the requirements outlined in the + OpenPOWER Foundation Work Group (WG) Process document. It was + created using the Master Template Guide version 0.9.5. Comments, + questions, etc. can be submitted to the public mailing list for this document at + TBD. + + + + + + 2016-05-04 + + + + Revision 2.0_pre1 - initial conversion from IBM document. Extracted from + Linux on Power Architecture Platform Reference (LoPAPR) version 1.1 dated March 24, + 2016 -- Appendix B (LoPAPR Binding) and Appendix C (PA Processor Binding). + + + + + + + + + + + + + + + + + + + + + + + + + + + + diff --git a/DeviceTree/ch_devtree_pa.xml b/DeviceTree/ch_devtree_pa.xml new file mode 100644 index 0000000..1cfe59c --- /dev/null +++ b/DeviceTree/ch_devtree_pa.xml @@ -0,0 +1,4376 @@ + + + + Processor Architecture Binding + +
+ Data Formats and Representations + + The cell size shall be 32 bits. Number ranges for + n, + u, and other cell-sized items are consistent with + 32-bit, two's-complement number representation. + The required alignment for items accessed with + a-addr addresses shall be four-byte aligned (i.e., a + multiple of 4). + Each operation involving a + qaddr address shall be performed with a single 32-bit + access to the addressed location; similarly, each + waddr access shall be performed with a single 16-bit + access. This implies four-byte alignment for + qaddrs and two-byte alignment for + waddrs. + +
+ +
+ Memory Management + +
+ PA Address Translation Model + + This section describes the model that is used for co-existence of + OF and client programs (i.e., OSs) with respect to address + translation. + The following overview of translation is provided so that the + issues relevant to OF for the PA can be discussed. Details that are not + relevant to OF issues (e.g., protection) are not described in detail; + , particularly Book III, should + be consulted for the details. For the scope of this section, terms will + be used as defined in + . + +
+ Translation requirements + + The default access mode of storage for load and stores (i.e., with + translation disabled -- referred to as + Real-Mode) within the PA assumes that caches are + enabled (in copy-back mode). In order to perform access to I/O device + registers, the access mode must be set to Cache-Inhibited, Guarded by + establishing a translation with this mode and enabling translation. Thus, + even though most of a client program and/or OF can run with translation + disabled, it must be enabled when performing I/O. + +
+ +
+ Segmented Address Translation + + + Note: The use of the term Virtual Address in this + section refers to the PA definition, while the rest of the document uses + the IEEE 1275 definition of virtual address. + + Note: The following description of PA address + translation is only one of several translation modes available and is + given for reference only. See + for complete details. + An Effective Address (EA) of a PA processor is 64(32) bits wide. + Each EA is translated into an 80(52)-bit Virtual Address (VA) by + prepending a 52(24)-bit Virtual Segment Id (VSID) to the 28 LSbs of the + effective address. On 32-bit implementations, the VSID is obtained by + indexing into a set of 16 Segment Registers (SRs) using the 4 MSbs of the + EA. On 64-bit implementations, the VSID is looked up in a Segment Table + using the 36 MSbs of the EA. Finally, the virtual address is translated + into a Real Address (RA). This is done by mapping the Virtual Page-Number + (VPN) (bits 0-67(39) of the VA) into a Real Page Number (RPN) and + concatenating this RPN with the byte offset (12 LSbs of the VA). The + mapping of VPN to RPN involves a hashing algorithm within a Hashed Page + Table (HTAB) to locate a Page Table Entry (PTE) that matches the VPN and + using that entry’s RPN component. If a valid entry is not found, a + Data Storage Interrupt (DSI) or Instruction Storage Interrupt (ISI) is + signalled, depending upon the source of the access. + This process is not performed for every translation! Processors + will typically have a Translation Look-aside Buffer (TLB) that caches the + most recent translations, thus exploiting the natural spatial locality of + programs to reduce the overhead of address translation. 64-bit + implementations may also implement a Segment Lookaside Buffer (SLB) for + the same reasons. On most PA processors, the TLB updates are performed in + hardware. However, the architecture allows an implementation to use a + software-assisted mechanism to perform the TLB updates. Such schemes must + not affect the architected state of the processor unless the translation + fails; i.e., the HTAB does not contain a valid PTE for the VA and a + DSI/ISI is signalled. + + Note: One unusual feature of this translation + mechanism is that valid translations might not be found in the HTAB; the + HTAB might be too small to contain all of the currently valid + translations. This introduces a level of complexity in the use of address + translation by OF, as discussed below. + +
+ +
+ Block Address Translation + + To further reduce the translation overhead for contiguous regions + of virtual and real address spaces (e.g., a frame buffer, or all of real + memory), the Block Address Translation (BAT) mechanism is also supported + by the PA. The Block Address Translation involves the use of BAT entries + that contain a Block Effective Page Index (BEPI), a Block Length (BL) + specifier and a Block Real Page Number (BRPN); the architecture defines 4 + BAT entries for data (DBAT entries) and 4 BAT entries for instruction + (IBAT entries) + The 601 has a single set of BAT entries that are shared by both + instruction and data accesses. + . BAT areas are restricted to a finite set of allowable + lengths, all of which are powers of 2. The smallest BAT area defined is + 128 KB (217 bytes). The largest BAT area defined is 256 MB (228 bytes). + The starting address of a BAT area in both EA space and RA space must be + a multiple of the area's length. + Block Address Translation is done my matching a number of upper + bits of the EA (specified by the BL value) against each of the BAT + entries. If a match is found, the corresponding BRPN bits replace the + matched bits in the EA to produce the RA. + Block Address Translation takes precedence over Segmented Address + Translation; i.e., if a mapping for a storage location is present in both + a BAT entry and a Page Table Entry or HTAB, the Block Address Translation + will be used. + + Note: Block Address Translation is a deprecated + translation mode of the PA. This description is retained here for + historical reference. See + for details on all supported + addressing mechanisms. + +
+
+ +
+ Open Firmware’s use of memory + + OF shall use the memory resources within the space indicated by the + + real-base, real-size, virt-base and + virt-size Configuration Variables defined for the PA. + As described in the applicable platform binding, a mechanism is defined + to enable OF to determine if its current configuration is consistent with + the requirements of the client. + If the client program has specific requirements for physical memory + or address space usage, it may establish requirements for OF's physical + and/or virtual address space usage by means of its program header. When + OF loads the client program, it inspects the program header, and if its + current usage of physical memory or virtual address space conflicts with + that specified in the program header, OF shall set the + real-base, + real-size, + virt-base, and + virt-size to the configuration variables as specified + in the header and restart itself. + Real-base, + real-size, + virt-base, and + virt-size may be specified as -1, in which case the + firmware is permitted to choose appropriate values for the variables + specified as -1. + If the values of the + real-size and/or + virt-size configuration variables do not provide + sufficient memory and/or virtual address space for the firmware's own + use, then the firmware shall not attempt to load a client program and the + condition should be reported to the user. The possibility of not being + able to comply with limitations on firmware's size should be tested as + the firmware is coming up in order to handle the possibility that a user + established an unworkable limitation on the size. Clients can minimize + this exposure by setting size to -1 and allowing OF to choose the + size. + A PA OF binding shall support two different addressing models, + depending upon the setting of the + real-mode? Configuration Variable. This variable + indicates the OF addressing mode that a client program expects; + false (0) indicates Virtual-Mode, + true (-1) indicates Real-Mode; the default value of + real-mode? is implementation dependent. + The management of + real-mode? is analogous to + little-endian?. OF determines its addressing mode + using the value of + real-mode?. If the current state of + real-mode? (and hence, the current state of OF) is + incorrect, it shall set + real-mode? appropriately and reset itself, possibly + by executing + reset-all. + Memory that cannot be allocated for general purpose use, for + example physical memory on LoPAR systems used for interrupt vectors and + implementation specific areas, shall not appear in the “ + available ” property of the + memory node. A Client Program that needs to use such + memory for its architected purpose must not claim that area prior to + use. + In the following two sections, some of conventions in Real-Mode and + Virtual-Mode address translations are described. Remaining sections + describe the assumptions that OF makes about the state and control of the + system in regard to OF’s use of system resources for three OF + interfaces (e.g. Device, User and Client interfaces). + +
+ Real-Mode + + In Real-Mode (when + real-mode? is + true), the use of address translations by OF and its + client are independent. Either they do not use translation, or their + translations are private; they do not share any translations. All + interfaces between the two must pass the real address of the data. Any + data structure shared by OF and its client that refers to + virt addresses in + , or this binding, must be real + addresses. + + Note: In particular, that the address of the Client + interface handler, that is passed to the client, has to be a real + address. + The Configuration Variables + real-base and + real-size should indicate the physical memory base + and size in which OF must locate itself. In Real-Mode, the Configuration + Variables + virt-base and + virt-size do not have meaning and should be set to + -1. + +
+ +
+ Virtual-Mode + + When + real-mode? is + false, OF shall configure itself to run in + Virtual-Mode. In Virtual-Mode, OF and its client + will share a single virtual address space. This binding provides + interfaces to allow OF and its client to ensure that this single virtual + address model can be maintained. + The Configuration Variables + virt-base and + virt-size should indicate the virtual address space + base address and size that OF should use. The Configuration Variables + real-base and + real-size should indicate the physical memory base + and size in which OF must locate itself. + +
+ +
+ Device Interface (Real-Mode) + + While OF is performing system initialization and probing functions, + it establishes and maintains its own translations. In particular, it + maintains its own Page Tables (and/or BAT entries) and handles any + DSI/ISI interrupts itself. + + Note: In Real-Mode, all translations will be + virt=real; the primary reason for translation is to + allow appropriate I/O accesses. + +
+ +
+ Device Interface (Virtual-Mode) + + OF will establish its own translation environment, handling DSI/ISI + interrupts as in the Real-Mode case. However, this environment will, in + general, contain translations in which virtual addresses do not equal + real addresses. The virtual address space used by OF must be compatible + with its client. + + Note: Since these virtual addresses will be used by + the Client and/or User Interfaces (e.g., for pointers to its code, + device-tree, etc.), their translations must be preserved until the client + OS decides that it no longer requires the services of OF. +
+ +
+ Client Interface (Real-Mode) + + In Real-Mode, addresses of client data are real.; the client must + ensure that all data areas referred to across the Client Interface are + valid real addresses. This may require moving data to meet any + requirements for contiguous storage areas (e.g., for + read/write calls). Translation shall be disabled + before the client interface call is made. + OF will typically have to maintain its translations in order to + perform I/O. Since the client may be running with translation enabled + (except for the Client interface call), OF shall save the state of all + relevant translation resources (e.g., SDR1, BATs) and restore them before + returning to the client. Likewise, it + may take over interrupts for its own use (e.g., for + doing “lazy” allocation of BATs); it shall preserve the state + of any interrupt vectors for its client. + Since the state of the address translation system is not + predictable to any interrupts, the client shall ensure that interrupts + are disabled before calling the Client Interface handler and call the + handler from only one CPU at a time. The client shall also ensure that + other processors do not generate translation exceptions for the duration + of the call. + Client programs are not required to assume responsibility for + physical memory management. The client program must use the OF claim + client interface service to allocate physical memory while physical + memory is managed by OF. Physical memory shall remain managed by OF until + the client program defines the real-mode physical memory management + assist callbacks. Physical memory must be managed by the client program + once the client program defines the real-mode physical memory management + assist callbacks. OF shall use the client program's real-mode physical + memory management assist callbacks to allocate physical memory after the + client program has assumed physical memory management. + In Real-Mode, + claim methods shall not allocate more pages than are + necessary to satisfy the request. + +
+ +
+ Client Interface (Virtual-Mode) + + Client interface calls are essentially “subroutine” + calls to OF. Hence, the client interface executes in the environment of + its client, including any translations that the OS has established. E.g., + addresses passed in to the client interface are assumed to be valid + virtual addresses within the scope of the OS. Any DSI/ISI interrupts are + either invalid addresses or caused by HTAB “spills”. In + either case, the OS has the responsibility for the handling of such + exceptions. + + Note: Addresses that the OF internal use will be + those that were established by the Device interface (or, by subsequent + actions of the Client or User interface). Thus, the client must preserve + these OF translations if it takes over the virtual memory management + function. + In addition to using existing translations, the Client Interface + might require the establishment of new translations (e.g., due to + map-in calls during + open time), or the removal of old translations (e.g., + during + map-out calls during + close time). Since this requires altering the + Client’s translation resources (e.g., Page Tables), possibly + handling spill conditions, OF cannot know how to perform these + updates. + Hence, there shall be + callback services provided by the client for use by + OF for such actions; see + . + In order to let clients (i.e., target OSs) know where OF lives in + the address space, the following rules shall be followed by an OF + implementation for the PA and by client programs. + OF: + + + + OF shall maintain its “translations” + “mmu”-node property (see + ) + + + + OF’s + claim methods shall not allocate more pages + than are necessary to satisfy the request. + + + + When a client executes + set-callback, OF shall attempt to invoke the + “translate” callback. If the translate callback is + implemented, OF shall cease use of address translation hardware, instead + using the client callbacks for changes to address translation. + + + + The + exit service must continue to work after a + set-callback that takes over address translation. + This implies that OF takes responsibility for address translation + hardware upon + exit and must maintain internal information about + translations that it requests of the client. + Client Programs: + + + + Client programs that take control of the management of address + translation hardware and expect to be able to subsequently invoke OF + client services must provide callbacks to assist OF in address + translation (see + ). + + + + A client program shall not directly manipulate any address + translation hardware before it either a) ceases to invoke OF client + services or b) issues a + set-callback to install the “translate” + callback. + + + + + Note: The intended sequence is that a client program + will first issue a set-callback and then take control of address + translation hardware. Address translation hardware includes BAT entries, + page table, segment registers, Machine State Register and the interrupt + vectors relating to translation faults. + +
+ +
+ User Interface (Real-Mode) + + In Real-Mode, OF regains total control of the system. As with the + Client interface in Real-Mode, it should save the state of the + translation resources (including interrupt vectors) upon entry and should + restore them upon exit. + +
+ +
+ User Interface (Virtual-Mode) + + When the User interface is invoked, OF is responsible for managing + the machine. Therefore, it will take over control of any relevant + interrupt vectors for its own handling. In particular, it will take over + DSI/ISI handling in order to report errors to the user for bad addresses, + protection violations, etc. However, as described above, one source of + DSI/ISI may simply be HTAB spills. As with the case of + map-in and + map-out calls, the User interface cannot know how to + handle such spill conditions, itself, or even if this is, in fact, a + spill versus a bad address. + Hence, this binding defines + callback services that the client provides for use by + OF; see + . + +
+ +
+ +
+ +
+ Properties + This section describes the standard properties of a PA OF + implementation. + +
+ CPU properties + + +
+ The Device Tree + + OF requires that the multiple instances of any device that appears + more than once in the device tree must be distinguishable by means of + their + “reg” properties. The + “reg” property must express the address + of each node relative to its parent bus. Furthermore, the core + specification says that the root node of the device tree usually + represents the main physical bus of the system. Thus, if processors are + not directly addressable on the main physical bus, as is expected to be + the case on many/most PA-based systems, the CPU nodes on such systems may + not be children of the root node but must instead be children of a + pseudo-device node. In this case, the name of the pseudo-device node, + which will usually be a child of the root node, shall be + “cpus”. + The “cpus” node shall have one child node of + device_type “cpu” for each processor. + +
+ +
+ Physical Address Formats and Representations for CPU + Nodes + + + +
+ Numerical Representation + The numerical representation of a processor’s + “address” in a LoPAR system shall consist of one cell, + encoded as follows (Bit# 0 refers to the least significant bit) + : + + + Numerical Representation of a Processor’s + “address” + + + + + + + + + + + + + Bit# + + + + + 3322222210987654 + + + + + 2222111132109876 + + + + + 1111110054321098 + + + + + 0000000076543210 + + + + + + + + phys.lo cell: + + + 00000000 + + + 00000000 + + + 00000000 + + + pppppppp + + + + +
+ where: + pppppppp is an 8-bit integer representing the + interprocessor interrupt identifier used by the platform. + +
+ +
+ Text Representation + + The text representation of a processor’s + “address” shall be an ASCII hexadecimal number in the range + 0...FF. + Conversion of the hexadecimal number from text representation to + numeric representation shall be case insensitive, and leading zeros shall + be permitted but not required. + Conversion from numeric representation to text representation shall + use the lower case forms of the hexadecimal digits in the range + a..f, suppressing leading zeros. + +
+ +
+ Unit Address Representation + + A processor’s “unit-number” (i.e. the first + component of its + “reg” value) is the interprocessor + interrupt destination identifier used by the platform. For a + uni-processor platform, the “unit-number” shall be + zero. + +
+ +
+ +
+ CPUS Node Properties + + The following properties shall be created within the + “cpus” node. + + + + “#address-cells” + + Standard property name to define the number of cells required + to represent the physical addresses for the “ + cpu ” nodes (i.e., the children of the “ + cpus ” node). + prop-encoded-array: Integer constant 1, encoded as + with encode-int. + The value of + “#address-cells” for the + “cpus” node shall be + 1. + + + + + “#size-cells” + + Standard + property name to define the number of cells necessary + to represent the length of a physical address range. + prop-encoded-array: Integer constant 0, encoded as + with encode-int. + The value of “ + #size-cells ” for the “cpus” + pseudo-device node is 0 because the processors that are represented by + the cpu nodes do not consume any physical address space. + + + + +
+ +
+ CPU Node Properties + + For each CPU in the system, a cpu-node shall be defined as a child + of + “cpus”. The following properties apply to + each of these nodes. The + cpus node shall not have “ + reg ” or “ + ranges ” properties. In general, properties in + a cpu-node that affect the software interface (for example properties + that convey the presence of instructions, presence of registers, or + location of resources) to the processor are preserved by the device tree + once presented upon boot. For a list of properties that may change before + a reboot, see + . + + + + “name” + + Standard property name. The value of this property + shall be of the form: “PowerPC,<name>”, where <name> + is the name of the processor chip which may be displayed to the user. + <name> + shall not contain underscores. + + + + + “device_type” + + Standard property name. The value of this + property for CPU nodes shall be + “cpu”. + + + + + “reg” + + Standard proper name to define a cpu node’s + unit-address. + prop-encoded-array: an integer encoded as with + encode-int. + For a cpu node, the first and only value of the + “reg” property shall be the number of the + per-processor interrupt line assigned to the processor represented by the + node. For a uni-processor platform, the value of the + “reg” property shall be zero. + + + + + “status” + + Standard property name. The value of the is + property shall be one of the following string values: + + + + “okay” + for a good processor. + + + + “fail” + for a processor that fails during power-on testing. + + + + “fail-offline” + for a processor that has been automatically deconfigured because of previous + failures. + + + + “disabled” + for a processor that has been manually deconfigured. + + + + + + + “cpu-version” + + property name: Represents the processor type. + prop-encoded-value: The value, encoded as with + encode-int, + shall be either the value obtained by + reading the Processor Version Register of the processor described by this + node, or the logical processor version as given in + . The first byte of the logical + processor version value shall be 0x0F. The values of the “Logical + Processor Version” column of + indicate that the processor + provides the base support described by that version of the architecture. + The presence and value of all optional and implementation dependent + features and facilities are described by their corresponding + properties. + + + Logical Processor Version Values + + + + + + + + + + Logical Processor Version + + + + + Property Value + + + + + + + + 2.04 + + + 0x0F000001 + + + + + 2.05 + + + 0x0F000002 + + + + + 2.06 + + + 0x0F000003 + + + + + 2.06 plus: + URG field in DSCR (Bits 55-57) + + + 0x0F100003 + + + + + 2.07 + + + 0x0F000004 + + + + + 2.08 + + + 0x0F000005 + + + + +
+ + + + + “clock-frequency” + + Standard property name, encoded as with + encode-int, that represents + the internal processor speed (in hertz) of this node. + + + + + “ibm,extended-clock-frequency” + + property name: Property that represents the internal + processor speed in hertz of this node. This property allows the encoding + of multi-giga-hertz quantities. + prop-encoded-array: Consisting of the low order 32 + bits of two cells (freq-hi, freq-lo) each encoded as with + encode-int, such that + their combined value is (the low order 32 bits of freq-hi || the low order + 32 bits of freq-lo). + + + + + “timebase-frequency” + + Standard property name, encoded as with + encode-int, + that represents the rate (in hertz) at + which the PA TimeBase and Decrementer registers are updated. + Note: The 601 PowerPC + processor does not have a timebase frequency, + therefore on a 601 PowerPC processor the value reported in this property + shall be 1 billion (1 x 109) which represents the logical rate of the + real time clock. + + + + + “ibm,extended-timebase-frequency” + + property name: Property that represents the rate in + hertz at which the PA TimeBase and Decrementer registers are updated. + This property allows the encoding of multi-giga-hertz quantities. + prop-encoded-array: Consisting of the low order 32 + bits of two cells (freq-hi, freq-lo) each encoded as with + encode-int, such that their combined + value is (the low order 32 bits of freq-hi || the low order 32 bits of freq-lo). + Note: The + “ibm,extended-timebase-frequency” + property will be deprecated from the architecture due to the emergence of the + “ibm,nominal-tbf” property and the lack + of a need for a two cell version of the + “timebase-frequency” property. + Implementations should not provide the + “ibm,extended-timebase-frequency” property. + + + + + “ibm,nominal-tbf” + + property name: Property, encoded as with + encode-int, + that represents the design nominal + timebase frequency (in hertz). + + + + + “ibm,tbu40-offset” + + property name: that provides the value that, when + added (ignoring overflow) to the processor TimeBase, yields a value + consistent with other platform partitions that utilize their respective + values of the property. If the property is missing, the default value is + zero. + prop-encoded-array: An eight byte, big endian, + unsigned, binary value. + + + + + “64-bit” + + prop-encoded-array: <none> + This property, if present, indicates that the PA processor defined + by this CPU node is a 64-bit implementation of the PA. The absence of + this property indicates that the microprocessor defined by this CPU node + is a 32 bit implementation of the PA + + + + + “64-bit-virtual-address” + + prop-encoded-array: <none> + This property, if present, indicates that the PA processor defined + by this CPU node supports the 64-bit virtual address subset of the 80-bit + virtual address as defined by the PA. The absence of this property + indicates that the PA processor defined by this CPU node supports the + full 80-bit virtual address defined by the PA. This property is only + valid for 64-bit implementations. + Note: The + “64-bit-virtual-address” + will be + deprecated from the architecture. Implementations should not provide this + property. + + + + + “603-translation” + + prop-encoded-array: <none> + This property, if present, indicates that the PA processor defined + by this CPU node uses the PowerPC 603 processor defined mechanism to + update its Translation Lookaside Buffers (TLBs). The absence of this + property indicates that the PA processor defined by this CPU node does + not use the PowerPC 603 processor defined mechanism to update its + TLBs. + + + + + “603-power-management” + + prop-encoded-array: <none> + This property, if present, indicates that the PA processor defined + by this CPU node implements the PowerPC 603 processor defined power + management states. The absence of this property indicates that the PA + processor defined by this CPU node does not support the PowerPC 603 + processor defined power management states. + + + + + “bus-frequency” + + Standard property name, encoded as with + encode-int, + that represents the speed (in hertz) of + this processor’s bus. + + + + + “ibm,extended-bus-frequency” + + property name: Property that represents the rate in + hertz of this processor’s bus. This property allows the encoding of + multi-giga-hertz quantities. + prop-encoded-array: Consisting of the low order 32 + bits of two cells (freq-hi, freq-lo) each encoded as with + encode-int, + such that their combined value is (the + low order 32 bits of freq-hi || the low order 32 bits of freq-lo). + + + + + “32-64-bridge” + + prop-encoded-array: <none> + This property, if present, indicates that the PA processor defined + by this CPU node implements the “Bridge Facilities and Instructions + for 64-bit Implementations” as described in an appendix of Book III + of + . The absence of this property + indicates that the PA processor defined by this CPU node does not support + these facilities and instructions. + + + + + “external-control” + + prop-encoded-array: <none> + This property, if present, indicates that the PA processor defined + by this CPU node implements the External Control Facility as described in + the “Optional Facilities and Instructions” appendix of Book + II of + . The absence of his property + indicates that the PA processor defined by this CPU node does not support + the External Control Facility. + + + + + “general-purpose” + + prop-encoded-array: <none> + This property, if present, indicates that the PA processor defined + by this CPU node implements the floating point instructions + fsqrt, + fsqrts and + stfiwx. The absence of this property indicates that + the PA processor defined by this CPU node does not support the floating + point instructions + fsqrt, + fsqrts and + stfiwx. + + + + + “reservation-granule-size” + + Standard property, encoded as with + encode-int, + that represents the reservation granule + size (i.e., the minimum size of lock variables) supported by this + processor, in bytes. + + + + + “graphics” + + prop-encoded-array: <none> + This property, if present, indicates that the PA processor defined + by this CPU node implements floating point instructions + fres, frsqrte, and + fsel. The absence of this property indicates that + the PA processor defined by this CPU node does not support the floating + point instructions + fres, frsqrte, and + fsel. + + + + + “performance-monitor” + + property name: Indicates that the processor described + by this node implements a performance monitor. + prop-encoded-array: Consists of a pair of values, + each encoded as with + encode-int. + The first value of the pair shall be 0 + indicating that the performance monitor functionality is implementation + specific. The second value of the pair represents the documentation + describing the performance monitor functionality implemented by the + processor described by this node. The documentation represented by the + second value is specified in + . + + + Documentation for Implementation Specific Performance + Monitors + + + + + + + + + + Second Value + + + + + Documentation + + + + + + + + 0 + + + + Power 5+ Performance Monitor Programmer’s + Guide + + + + + + 1 + + + + Power 7 Performance Monitor Programmer’s + Guide + + + + + +
+ + + + + “ibm,vmx” + + property name that indicates that the processor + supports the POWER VMX architecture. + prop-encoded-array: an integer encoded as with + encode-int, + that represents the level of the VMX + architecture supported. The first level supported is the value 1. The + value of 1 represents the level of support described by the + A Vector/SIMD Multimedia eXtension to the PowerPC Architecture, + Specification Revision 1.2.3, 7/18/97 specification. The value + of 2 represents the level of support provided by the VSX option of + level 2.06. + + + + + “ibm,segment-page-sizes” + + property name: that indicates the segment base page + sizes and related encodings supported by the processor. + prop-encoded-array: one or more + segment-page-size-descriptor(s). + segment-page-size-descriptor: a + segment-page-size-header followed by a pte-lp-descriptor. + segment-page-size-header: Consists of three cells + (X,Y,Z) encoded as with + encode-int. + The first cell represents the base page + size of the segment (the page size which determines the hash value used + to locate the segment's page table entries) as 2 + X. The second cell contains the SLB encoding that, + ORed with the RS register value for use by a slbmte instruction, selects + this segment's base page size. Note, the low order bits of the cell Y are + aligned with the low order bits of RS and the RS's L and LP bits are zero + prior to the logical OR operation. The third cell contains the number of + pte-lp-encodings in the pte-lp-descriptor. + pte-lp-descriptor: Consists of Z (from the + segment-page-size-header) pte-lp-encoding(s), one for each of the page + sizes supported for this base segment page size. + pte-lp-encoding: Each pte-lp-encoding consists of + two cells (P,Q) encoded as with + encode-int. + The first cell represents the page size + of the encoding as 2 + P (thus implying the number of low order RPN bits + that are available to page size encoding). The second cell, left shifted + 12 bit positions, is the encoding to be entered into the available low + order RPN bits to represent this page size for this segment base page + size. + Note: A + segment-page-size-descriptor applies to a segment + only if the size of the segment is greater than or equal to all of the + page sizes within the + pte-lp-encoding (s) contained within the + segment-page-size-descriptor. + + + + + “ibm,processor-page-sizes” + + property name: Relates the number and sizes of the virtual memory + page sizes supported by the processor describe by this node. + prop-encoded-array: One to N cells in ascending + value order, each encoded as with + encode-int, each cell represents the size of a + supported virtual memory page where the value of the cell is the power of + 2 of the cell size. i.e. a 4 K page size is represented by the value 12 + (4 K= 2 + 12) etc. + + + + + “ibm,processor-segment-sizes” + + property name: Relates the number and sizes of the + virtual memory segment sizes supported by the processor described by this + node. + prop-encoded-array: One to N cells in ascending + value order of the segment selector (SLBE B field), each encoded as with + encode-int, each positive value cell represents the + size of a supported virtual memory segment where the value of the cell is + the power of 2 of the segment size. That is, a 256Meg segment size is + represented by the value 28 (256Meg = 2 + 28) etc. (negative valued cells represent + unsupported encodings). + + + + + “ibm,processor-storage-keys” + + property name indicating the number of virtual + storage keys supported by the processor described by this node. + prop-encoded-array: Consists of two cells encoded as + with encode-int. + The first cell represents the number of + virtual storage keys supported for data accesses while the second cell + represents the number of virtual storage keys supported for instruction + accesses. The cell value of zero indicates that no storage keys are + supported for the access type. + + + + + “ibm,processor-vadd-size” + + property name indicating the number of virtual + address bits that are supported by the processor described by this + node. + prop-encode-array: An integer, encoded as with + encode-int, that represents the number of supported + virtual address bits. + Note: A processor + described by this node implements + the least significant + “ibm,processor-vadd-size” + bits of the architected virtual address. + + + + + “ibm,vrma-page-sizes” + + property-name: Maps the VRMASD field values + implemented by the processor described by this node to their page + sizes. + prop-encoded-array: Array of one or more + VRMA page-size-descriptor (s) starting with the value + selected by the firmware when booting the partition, followed by the + other values supported by the platform. + VRMA page-size-descriptor: A pair of cells encoded + as with + encode-int; The first cell is the log base 2 of the + page size. The second cell contains, in its low order bits, the VRMASD + field value to achieve that supported size. The high order bits of the + second cell are zero. + + + + + “ibm,estimate-precision” + + property name: Relates PA estimate instruction + mnemonics to precisions supported by the processor described by this + node. + prop-encoded-array: One or more + instruction-precision descriptor (s). + + instruction-precision descriptor: An + instruction descriptor followed by a + precision descriptor. An + instruction-precision descriptor relates one estimate + instruction mnemonic to the precision supported by the processor + described by this node for that estimate instruction mnemonic. + instruction descriptor: Consists of one PA + instruction mnemonic encoded as with + encode-string. + precision descriptor: Consists of an integer, encoded + as with + encode-int, + specifying the number of bits of + precision the processor described by this node supports for an + instruction mnemonic. + + + + + “ibm,dfp” + + property name: Indicates that the processor described + by this node supports the Decimal Floating Point (DFP) + architecture. + prop-encoded-value: an integer, encoded as with + encode-int, + that represents the level of DFP support + of the CPU described by this node. The absolute value of the integer + represents the level of the DFP architecture supported. The sign of the + integer indicates how the architecture level is supported. A positive + integer indicates native support while a negative integer indicates + emulation assisted support. The absolute values supported are as + follows: + 1: Represents the level of support defined by Version 2.05 of the + . + 2: Represents the level of support defined by Version 2.06 of the + . + + + + + “ibm,purr” + + property name: Indicates that the processor + described by this node implements a Processor Utilization of Resources + Register (PURR). + prop-encoded-value: an integer, encoded as with + encode-int, + that represents the level of PURR + architecture supported. The first level supported is the value 1 and is + defined by Section 6.5 “Processor Utilization of Resources + Register” of Book III of version 2.02 of the PA. + + + + + “ibm,spurr” + + property name: Indicates that the processor + described by this node implements a Scaled Processor Utilization of + Resources Register (SPURR). + prop-encoded-value: an integer, encoded as with + encode-int, + that represents the level of SPURR + architecture supported. The value of 1 represents the level of support + defined by Version 2.05 of the + . + + + + + “ibm,pa-features” + + property name: Indicates level of support of several + extended features of the Processor Architecture. + prop-encoded-array: One or more + attribute-descriptor (s). + attribute-descriptor: Consists of an + attribute-header immediately followed by an + attribute-specifier. + attribute-header: Consists of two bytes. The first + byte is an unsigned integer representing a value from 1 to 254. The first + byte specifies the number of bytes implemented by the platform of the + attribute-specifier. The second byte is an unsigned + integer specifying the + attribute-specifier-type. + attribute-specifier: The + attribute-specifier is defined by the + attribute-specifier-type of the + attribute-header. The + attribute-specifier for the + attribute-specifier-type value of 0 is defined by + . + + + Definition for + <emphasis>attribute-specifier</emphasis> + <emphasis>attribute-specifier-type</emphasis> value 0 + + + + + + + + + + Byte Number + + + + + Bit Number + + + + + Attribute Name + + + + + Description + + + + + + + + 0 + + + 0 + + + Memory Management Unit (MMU) + + + The value of 1 indicates MMU support; else not + supported. + + + + + 1 + + + Floating Point Unit (FPU) + + + The value of 1 indicates FPU support; else not + supported. + + + + + 2 + + + Segment Lookaside Buffer (SLB). + + + The value of 1 indicates SLB support; else not + supported. + + + + + 3 + + + RUN field + + + The value of 1 indicates support for the RUN field of the + Control Register (CTRL, SPR #152); else not supported. + + + + + 4 + + + Reserved + + + Reserved bits within defined bytes + shall be zero. + + + + + 5 + + + Data Address Breakpoint Register (DABR) + + + The value of 1 indicates DABR support; else not + supported. + + + + + 6 + + + No Execute (N) bit in Page Table Entries. + + + The value of 1 indicates No Execute (N) bit in Page Table + Entry support; else not supported. + + + + + 7 + + + Write Through Required (W) bit + + + The value of 1 indicates setting the W bit to 1 (write + through always) is supported; else attempting to set the W bit + to 1 has no effect + + + + + 1 + + + 0 + + + Memory Coherence Required (M) bit + + + The value of 1 indicates that setting the M bit to 0 + (main storage not always coherent) is supported; else + attempting to set the M bit to 0 has no effect. + + + + + 1 + + + Data Storage Interrupt Status Register (DSISR) set on an + alignment interrupt. + + + The value of 1 indicates that the DSISR is set on an + alignment interrupt as described by version 2.01 of PA; else + the DSISR is not set on alignment interrupt as described by + version 2.01 of PA. + + + + + 2 + + + I=1 (cache inhibited) Large Pages + + + The value of 1 indicates support for I=1 (cache + inhibited) large pages; else not supported. + + + + + 3 + + + Round to Integer (from floating point) group of + instructions. + + + The value of 1 indicates support for the + frin, friz, frip, and + frim instructions; else these instructions + are not supported. + + + + + 4 + + + Data Address Breakpoint Register Extension (DABRX) + + + The value of 1 indicates support for the DABRX + architecture as defined by version 2.02 of PA; else not + supported. + + + + + 5 + + + User Accessible SPRG3 + + + The value of 1 indicates support for accessing SPRG3 in + Problem State; else SPRG3 is not accessible in Problem + State. + + + + + 6 + + + Reading an invalid SLB entry returns zeros. + + + The value of 1 indicates that reading an invalid SLB + entry always returns zeros; else non-zero values may be + returned. + + + + + 7 + + + Support for “110” value of the Page + Protection (PP) bits. + + + The value of 1 indicates support for “110” + value of the Page Protection (PP) bits as described by version + 2.04 of PA; else “110” is not supported.as + described by 2.04 of PA. + + + + + 2 + + + 0 + + + Virtualized Partition Memory (VPM) + + + The value of 1 indicates support for Virtualized + Partition Memory (VPM) as described by version 2.04 of PA; else + not supported. + + + + + 1 + + + 2.05 Data Stream Support + + + The value of 1 indicates that data streams as described + by version 2.05 of PA are supported; else not supported. + + + + + 2 + + + Reserved + + + Reserved bits within defined bytes + shall be zero. + + + + + 3 + + + Data Address Register (DAR) set on an alignment + interrupt. + + + The value of 1 indicates that the DAR is set on an + alignment interrupt as described by version 2.01 of PA; else + the DAR is not set on alignment interrupt as described by + version 2.01 of PA. + + + + + 4 + + + Reserved + + + Reserved bits within defined bytes + shall be zero. + + + + + 5 + + + Program Priority Register (PPR) + + + The value of 1 indicates that the PPR is implemented as + described by version 2.03 of PA; else the PPR is not + implemented as described by version 2.03 of PA. + + + + + 6 + + + 2.02 Data Stream Support + + + The value of 1 indicates that data streams as described + by version 2.02 of PA are supported; else not supported. + + + + + 7 + + + 2.06 Data Stream Support + + + The value of 1 indicates that data streams as described + by version 2.06 of PA are supported; else the 2.06 version data + streams are not supported. + + + + + 3 + + + 0 + + + LSD in DSCR(Bit 58) + + + The value of 1indicates that “Load Stream + Disable” bit of the Data Stream Control Register is + implemented + + + + + 1 + + + URG in DSCR (Bits 55::57) + + + The value of 1 indicates that the “Depth Attainment + Urgency” field of the Data Stream Control Register is + implemented. + + + + + 2-7 + + + Reserved + + + Reserved bits within defined bytes + shall be zero. + + + + + 4 + + + Storage Order Options + + + Byte bits define the availability of specific + options + + + + + 0 + + + 2.06 Strong Storage Order + + + The value of 1 indicates that Strong Storage Order as + defined by version 2.06 of PA is supported; else not. + + + + + 1-7 + + + Reserved for future storage order options + + + Reserved bits within defined bytes + shall be zero. + + + + + 5 + + + 0 + + + Little Endian + + + The value of 1indicates support for Little Endian as + described by version 2.03 of PA; else not supported. + + + + + 1 + + + Come From Address Register (CFAR) + + + The value of 1 indicates that the CFAR is implemented as + described by version 2.05 of PA; else the CFAR is not + implemented as described by version 2.05 of PA. + + + + + 2 + + + Elemental Barriers + + + The value of 1 indicates that elemental barriers are + supported; else elemental barriers are not supported. + + + + + 3 + + + 2.07 load/store quadword + + + The value of 1 indicates that the load/store quadword + category as described by version 2.07 of POWER ISA is + supported; else the 2.07 version load/store quadword category + is not supported. + + + + + 4-7 + + + Reserved + + + Reserved bits within defined bytes + shall be zero. + + + + + 6-7 + + + Data Streaming Specifications + + + + + 0 + + + 2.07 Data Streaming Support + + + The value of 1 indicates that data streams as described + by version 2.07 of POWER ISA are supported; else the 2.07 + version data streams are not supported. + + + + + 1-7 + + + Reserved + + + Reserved bits within defined bytes + shall be zero. + + + + + 8-15 + + + 0-7 + + + Reserved Co-Processor Option + + + Individual non-zero bits indicate available coprocessor + types per their architected ACOP bit locations. (the value + 0x0000000000000000 indicates that moving to/from the ACOP SPR + or the ICSWX instruction should not be attempted) + + + + + 16-17 + + + Level of Vector Category Support + + + + + 0 + + + 2.07 Vector Support + + + The value of 1 indicates that the vector category as + described by version 2.07 of POWER ISA is supported; else the + 2.07 version vector category is not supported. + + + + + 1-7 + + + Reserved + + + Reserved bits within defined bytes + shall be zero. + + + + + 18-19 + + + Level of Vector Scalar Category Support + + + + + 0 + + + 2.07 Vector Scalar Support + + + The value of 1 indicates that the vector scalar category + as described by version 2.07 of POWER ISA is supported; else + the 2.07 version vector scalar category is not + supported. + + + + + 1-7 + + + Reserved + + + Reserved bits within defined bytes + shall be zero. + + + + + 20-21 + + + Level of Vector.XOR Category Support + + + + + 0 + + + 2.07 Vector.XOR Support + + + The value of 1 indicates that the vector.xor category as + described by version 2.07 of POWER ISA is supported; else the + 2.07 version vector.xor category is not supported. + + + + + 1-7 + + + Reserved + + + Reserved bits within defined bytes + shall be zero. + + + + + 22-23 + + + Level of Transactional Memory Category Support + + + + + 0 + + + 2.07 Transactional Memory Support + + + The value of 1 indicates that the Transactional Memory + Category as described by version 2.07 of POWER ISA is + supported; else the 2.07 version Transactional Memory Category + is not supported. + + + + + 1-7 + + + Reserved + + + Reserved bits within defined bytes + shall be zero. + + + + + 24-255 + + + 0-7 + + + Undefined + + + Readers + shall ignore undefined bytes if + present. + + + + +
+ + + + + “ibm,pi-features” + + property name: Indicates level of support of + processor implementation specific options not described by the Processor + Architecture. + prop-encoded-array: One or more + pi-attribute-descriptor (s). + pi-attribute-descriptor: Consists of a + pi-attribute-header immediately followed by a + pi-attribute-specifier. + pi-attribute-header: Consists of two bytes. The first + byte is an unsigned integer representing a value from 1 to 254. The first + byte specifies the number of bytes implemented by the platform of the + pi-attribute-specifier. The second byte is an + unsigned integer specifying the + pi-attribute-specifier-type. + pi-attribute-specifier: The + pi-attribute-specifier is defined by the + pi-attribute-specifier-type of the + pi-attribute-header. The + pi-attribute-specifier for the + pi-attribute-specifier-type value of 0 is defined by + . + + + Definition for + <emphasis>‘</emphasis> + <emphasis>pi-attribute-specifier-type</emphasis> value 0 + + + + + + + + + + Byte Number + + + + + Bit Number + + + + + Attribute Name + + + + + Description + + + + + + + + 0 + + + 0 + + + P4 Data Address Register (DAR) setting on alignment + interrupt. + + + The value of 1 indicates that the DAR is set on an + alignment interrupt as described by version 2.01 of PA except + for the case where the interrupt is caused by an unsupported + access to cache inhibited space. In this case, the DAR will be + set to the effective address of the first access into the cache + inhibited space. The value of 0 indicates that the processor + does not adhere to this behavior. + + + + + 1 + + + Reserved + + + Reserved bits within defined bytes + shall be zero. + + + + + 2 + + + Ordered Thread Activation/Deactivation + + + The value of 1 indicates that the + “ibm,ppc-interrupt-server-#s” property + conveys the order that threads need to be activated and + deactivated in to achieve optimal performance; else no need to + activate and deactivate threads in order. + + + + + 3-7 + + + Reserved + + + Reserved bits within defined bytes + shall be zero. + + + + + 1-255 + + + 0-7 + + + Reserved + + + Reserved bits within defined bytes + shall be zero. + + + + +
+ + + + + “ibm,negotiated-pa-features” + + property name: Indicates level + of support negotiated via the + ibm,client-architecture-support + method (See + ) of several extended features + of the Processor Architecture. + prop-encoded-array: One or more + negotiated-pa-attribute-descriptor (s). + negotiated-pa-attribute-descriptor: Consists of a + negotiated-pa-attribute-header immediately followed + by a + negotiated-pa-attribute-specifier. + negotiated-pa-attribute-header: Consists of two + bytes. The first byte is an unsigned integer representing a value from 1 + to 254. The first byte specifies the number of bytes implemented by the + platform of the + negotiated-pa-attribute-specifier. The second byte + is an unsigned integer specifying the + negotiated-pa-attribute-specifier-type. + negotiated-pa-attribute-specifier: The + negotiated-pa-attribute-specifier is defined by the + negotiated-pa-attribute-specifier-type of the + negotiated-pa-attribute-header. The + negotiated-pa-attribute-specifier for the + negotiated-pa-attribute-specifier-type value of 0 is + defined by + . + + + Definition for + <emphasis>negotiated-pa-attribute-specifier</emphasis> + <emphasis>negotiated-pa-attribute-specifier-type</emphasis> value + 0 + + + + + + + + + + Byte Number + + + + + Bit Number + + + + + Attribute Name + + + + + Description + + + + + + + + 0 + + + 0 + + + TC Set + + + The value of 1 indicates that the TC bit is implemented + as described by version 2.05 of PA and set to a value of 1; + else the TC bit is not implemented as described by version 2.05 + of PA or not set to a value of 1. + + + + + 1-7 + + + Reserved + + + Reserved bits within defined bytes + shall be zero. + + + + + 1-255 + + + 0-7 + + + Reserved + + + Reserved bits within defined bytes + shall be zero. + + + + +
+ + + + + “ibm,raw-pi-features” + + property name: Indicates level of support of + processor implementation specific options not described by the Processor + Architecture and not supported on partitions that contain the + “ibm,migratable-partition” property. + prop-encoded-array: One or more + raw-pi-attribute-descriptor (s). + raw-pi-attribute-descriptor: Consists of a + raw-pi-attribute-header immediately followed by a + raw-pi-attribute-specifier. + raw-pi-attribute-header: Consists of two bytes. The + first byte is an unsigned integer representing a value from 1 to 254. The + first byte specifies the number of bytes implemented by the platform of + the + raw-pi-attribute-specifier. The second byte is an + unsigned integer specifying the + raw-pi-attribute-specifier-type. + raw-pi-attribute-specifier: The + raw-pi-attribute-specifier is defined by the + raw-pi-attribute-specifier-type of the + raw-pi-attribute-header. The + raw-pi-attribute-specifier for the + raw-pi-attribute-specifier-type value of 0 is defined + by + . + + + Definition for + <emphasis>raw-pi-attribute-specifier</emphasis> + <emphasis>raw-pi-attribute-specifier-type</emphasis> value 0 + + + + + + + + + + Byte Number + + + + + Bit Number + + + + + Attribute Name + + + + + Description + + + + + + + + 0 + + + 0 + + + FPR GPR Move Instructions + + + The value of 1 indicates that the PA processor defined by + this CPU node implements the + mftgpr and + mffgpr instructions as described by IBM + POWER6® CEC Book IV Implementation + Features; else not supported. + + + + + 1-7 + + + Reserved + + + Reserved bits within defined bytes + shall be zero. + + + + + 1-255 + + + 0-7 + + + Reserved + + + Reserved bits within defined bytes + shall be zero. + + + + +
+ + + + + “ibm,pa-optimizations” + + property name: Indicates the level of support of + performance variabilities described by the Processor Architecture. + prop-encoded-array: One or more + pa-optimization-attribute-descriptor (s). + pa-optimization-attribute-descriptor: Consists of a + pa-optimization-attribute-header immediately followed + by a + pa-optimization-attribute-specifier. + pa-optimization-attribute-header: Consists of two + bytes. The first byte is an unsigned integer representing a value from 1 + to 254. The first byte specifies the number of bytes implemented by the + platform of the + pa-optimization-attribute-specifier. The second byte + is an unsigned integer specifying the + pa-optimization-attribute-specifier-type. + pa-optimization-attribute-specifier: The + pa-optimization-attribute-specifier is defined by the + pa-optimization-attribute-specifier-type of the + pa-optimization-attribute-header. The + pa-optimization-attribute-specifier for the + pa-optimization-attribute-specifier-type value of 0 + is defined by + . + + + Definition for + <emphasis>pa-optimization-attribute-specifier</emphasis> + <emphasis>pa-optimization-attribute-specifier-type</emphasis> value + 0 + + + + + + + + + + Byte Number + + + + + Bit Number + + + + + Attribute Name + + + + + Description + + + + + + + + 0 + + + 0-7 + + + Stream IDs + + + The value is an unsigned quantity indicating the number + of data stream IDs supported. The value of this byte + shall be zero for processors that do not + support data streams. + + + + + 1 + + + 0-7 + + + Default Prefetch Depth + + + The value in the Default Prefetch Depth (DPFD) field of + the Logical Partitioning Control Register (LPCR) as described + by version 2.05 of PA. Unimplemented high order bits + shall be zero. This byte is valid only if + the “2.05 Data Stream Support” bit of + “ibm,pa-features” is set to + one; else this byte is undefined. + + + + + 2-255 + + + 0-7 + + + Reserved + + + Reserved bits within defined bytes + shall be zero. + + + + +
+ + + + +
+ +
+ TLB properties + + Since the PA defines the MMU as being part of the processor, the + properties defined by Section 3.6.5 of + and the following MMU-related + properties shall be presented under “cpu” nodes. + + + + “tlb-size” + + Standard property name, encoded as with + encode-int, that represents + the total number of TLB entries. + + + + + “tlb-sets” + + Standard property name, encoded as with + encode-int, that represents + the number of associativity sets of the TLB. A value of 1 indicates that the TLB is + fully-associative. + + + + + “tlb-split” + + This property, if present, shall indicate that the TLB has a split + organization. The absence of this property shall indicate that the TLB + has a unified organization. + + + + + “d-tlb-size” + + Standard property name, encoded as with + encode-int, that represents + the total number of d-TLB entries. + + + + + “d-tlb-sets” + + Standard property name, encoded as with + encode-int, that represents + the number of associativity sets of the d-TLB. A value of 1 indicates that the + d-TLB is fully-associative. + + + + + “i-tlb-size” + + Standard property name, encoded as with + encode-int, that + represents the total number of i-TLB entries. + + + + + “i-tlb-sets” + + Standard property name, encoded as with + encode-int, that represents + the number of associativity sets of the i-TLB. A value of 1 indicates that the + i-TLB is fully-associative. + + + + + “tlbia” + + prop-encoded-array: <none> + This property, if present, indicates that the PA processor defined + by this CPU node implements thetlbia instruction. The absence + of this property indicates that the PA processor defined by this CPU node does + not support the tlbia instruction. + + + + +
+ +
+ Internal (L1) cache properties + + The PA defines a Harvard-style cache architecture; however, unified + caches are an implementation option. All of the PA cache instructions act + upon a cache “block”. The coherence block size, if different + from the cache block size, is reported via the + “i-cache-line-size” and + “d-cache-line-size” properties. The + internal (also referred to as “L1”) caches of PA processors + are represented in the OF device tree by the following properties + contained under + “cpu” nodes. + + + + “cache-unified” + + This property, if present, indicates that the internal cache has a + physically unified organization. Absence of this property indicates that + the internal caches are implemented as separate instruction and data + caches. Unless otherwise noted, separate instruction and data caches + require the architected instruction sequence for instruction modification + so that data cache stores appear in the instruction cache. + + + + + “i-cache-size” + + Standard property name, encoded as with + encode-int, that represents + the total size (in bytes) of the internal instruction cache. + + + + + “i-cache-sets” + + Standard property name, encoded as with + encode-int, that represents + number of associativity sets of the internal instruction cache. A value of 1 + signifies that the instruction cache is fully associative. + + + + + “i-cache-block-size” + + Standard property name, encoded as with + encode-int, that represents + the internal instruction cache's block size, in bytes. + + + + + “d-cache-size” + + Standard property name, encoded as with + encode-int, that represents + the total size (in bytes) of the internal data cache. + + + + + “d-cache-sets” + + Standard property name, encoded as with + encode-int, that represents + number of associativity sets of the internal data cache. A value of 1 signifies + that the data cache is fully associative. + + + + + “d-cache-block-size” + + Standard property name, encoded as with + encode-int, that represents + the internal (L1) data cache's block size, in bytes. + + + + + “l2-cache” + + Standard property name, encoded as with + encode-int, that represents + the next level of cache in the memory hierarchy. + Absence of this property indicates that no further levels of cache + are present. If present, its value is the + phandle of the device node that represents the next + level of cache. + + + + + “i-cache-line-size” + + Standard property name, encoded as with + encode-int, that represents + the internal instruction cache's coherency block size (line size), in bytes, + if different than its cache block size. + + + + + “d-cache-line-size” + + Standard property name, encoded as with + encode-int, that represents + the internal data cache's coherency block size (line size), in bytes, if different + than its cache block size. + Note: If this is a unified cache, the + corresponding i- and d- sizes must be equal. + + + + +
+ +
+ Memory Management Unit properties + + To aid a client in “taking over” the translation + mechanism and still interact with OF (via the client interface), the + client needs to know what translations have been established by OF. The + following standard property shall exist within the package to which the + “mmu” property of the /chosen package refers. + + + + “translations” + + This property, consisting of sets of translations, defines the + currently active translations that have been established by OF (e.g., + using map). Each set has the following format: + + Each value is encoded as with + encode-int. + + + + + +
+ +
+ SLB properties + + Since the PA defines the MMU as being part of the processor, the + properties defined by Section 3.6.5 of + and the following MMU-related + properties as appropriate to the specific processor implementation shall + be presented under “cpu” nodes. + + + + “slb-size” + + Standard property name, encoded as with + encode-int, that + represents the total number of SLB entries. + Note: + requires that the SLB be + fully-associative, and appear to be a unified organization. Therefore, + properties to report SLB sets, split, and sizes and sets of i and d SLBs + are not defined. + + + + +
+ +
+ +
+ Ancillary (L2,L3...) cache node properties + Some systems might include secondary (L2) or tertiary (L3), etc. + cache(s). As with the L1 caches, they can be implemented as either + Harvard-style or unified. Unlike the L1 properties, that are contained + within the + “cpu” nodes, the properties of ancillary + caches are contained within other device tree nodes. + The following properties define the characteristics of such + ancillary caches. These properties shall be contained within a child node + of one of the CPU nodes or, for platforms that support dynamic + reconfiguration of cpus, the CPUS node; this is to allow path-name access + to the node. These properties shall always be contained within a child + node of the CPUS node. All + “cpu” nodes that share the same ancillary + cache (including the cpu node under which the ancillary cache node is + contained) shall contain an + “l2-cache” property whose value is the + phandle of that ancillary cache node. + + Note: The + “l2-cache” property shall be used in one + level of the cache hierarchy to represent the next level. The device node + for a subsequent level shall appear as a child of one of the caches in + the hierarchy to allow path-name traversal. The preceding sentence does + not apply to platforms that support dynamic reconfiguration of cpus or + platforms designed after 07/2005. + + + + “device_type” + + Standard property name; the device_type of ancillary cache + nodes shall be + “cache”. + + + + + “cache-unified” + + This property, if present, indicates that the cache at this node + has a physically unified organization. Absence of this property indicates + that the caches at this node are implemented as separate instruction and + data caches. Unless otherwise noted, separate instruction and data caches + require the architected instruction sequence for instruction modification + so that data cache stores appear in the instruction cache. + + + + + “i-cache-size” + + Standard property name, encoded as with + encode-int, that represents the total size (in + bytes) of the instruction cache at this node. + + + + + “i-cache-sets” + + Standard property name, encoded as with + encode-int, that represents number of associativity + sets of the instruction cache at this node. A value of 1 signifies that + the instruction cache is fully associative. + + + + + “d-cache-size” + + Standard property name, encoded as with + encode-int, that represents the total size (in + bytes) of the data cache at this node. + + + + + “d-cache-sets” + + Standard property name, encoded as with + encode-int, that represents number of associativity + sets of the instruction cache at this node. A value of 1 signifies that + the instruction cache is fully associative. + + + + + “l2-cache” + + Standard property name, encoded as with + encode-int, that represents the next level of cache + in the memory hierarchy. + Absence of this property indicates that no further levels of cache + are present. If present, its value is the + phandle of the device node that represents the cache + at the next level. + + + + + “i-cache-line-size” + + Standard property name, encoded as with + encode-int, that represents the internal instruction + cache's line size, in bytes, if different than its block size. + + + + + “d-cache-line-size” + + Standard property name, encoded as with + encode-int, that represents the internal data + cache's line size, in bytes, if different than its block size. + + Note: If this is a unified cache, the corresponding + i- and d- sizes must be equal. + + + + +
+ +
+ +
+ Methods + + This section describes the additional standard methods required of a + PA OF implementation. + +
+ MMU related methods + + The MMU methods defined by section 3.6.5. of + shall be implemented by CPU + nodes. The value of the + mode parameter for the relevant methods (e.g., + map) shall be the value that is contained within + PTEs that control Write-through, Cache-Inhibit, Memory-coherent, Guarded + and the 2 protection bits; thus, its format is: + WIMGxPP, where x is a reserved bit that shall be 0. + In order for I/O accesses to be properly performed in a LoPAR system, + address ranges that are mapped by + map-in shall be marked as Cache-Inhibited, + Guarded. + The default mode (i.e., the mode specified when the value of the + mode argument is -1) for the + map-in and + modify MMU methods of CPU nodes is defined as + follows: + If the beginning of the physical address range affected by the + operation refers to system memory, the values for + WIMGxPP shall be W=0, I=0, M=0, G=1, PP=10. + If the beginning of the physical address range affected by the + operation refers to an I/O address, the values for WIMGxPP shall be W=1, + I=1, M=0, G=1, PP=10. + +
+ +
+ +
+ Client Interface Requirements + + A PA OF implementation shall implement a client interface (as defined + in chapter 6 of + ) according to the specifications + contained within this section. + +
+ Calling Conventions + To invoke a client interface service, a + client program constructs a client interface + argument array as specified in the core OF document, + places its address in + r3 and transfers to the + client interface handler, with the return address in + lr. (A typical way of accomplishing this is to copy + the + client interface handler's address into + ctr and executing a + bctrl.) + The term “preserved” below shall mean that the register + has the same value when returning as it did when the call was + made. + + + Register usage conventions + + + + + + + + + + + + Register(s) + + + + + Value -- real-mode + + + + + Value -- virt-mode + + + + + Notes + + + + + + + +   + + + If either the FWNMI, or LPAR option is implemented + + + If neither the FWNMI or LPAR option is implemented + + + If either the FWNMI, or LPAR option is implemented + + + If neither the FWNMI or LPAR option is implemented + + +   + + + + + msr + + + client interface shall preserve + + + client interface shall preserve + + + same as real-mode + + + client interface shall not modify + + +   + + + + + cr + + + client interface shall preserve + + + client interface shall preserve + + + same as real-mode + + + same as real-mode + + + 1 + + + + + r1-r2 + + + client interface shall preserve + + + client interface shall preserve + + + same as real-mode + + + same as real-mode + + +   + + + + + r3 + + + argument array address on client interface entry + + + argument array address on client interface entry + + + same as real-mode + + + same as real-mode + + + 2 + + + + +   + + + result value (true or false) on client interface + return + + + result value (true or false) on client interface + return + + + same as real-mode + + + same as real-mode + + + 2 + + + + + r13-r31 + + + client interface shall preserve + + + client interface shall preserve + + + same as real-mode + + + same as real-mode + + +   + + + + + sprg0, sprg1, and sprg3 + + + client interface shall preserve + + + client interface shall not modify + + + same as real-mode + + + same as real-mode + + +   + + + + + fpscr + + + client interface shall preserve + + + client interface shall preserve + + + same as real-mode + + + same as real-mode + + +   + + + + + f0-f31 + + + client interface shall preserve + + + client interface shall preserve + + + same as real-mode + + + same as real-mode + + +   + + + + + lr, + ctr, + xer + + + undefined + + + undefined + + + same as real-mode + + + same as real-mode + + +   + + + + + sr0-sr15 + + + client interface shall preserve + + + client interface shall preserve + + + same as real-mode + + + client interface shall not modify + + +   + + + + + vr0-vr31 + + + client interface shall preserve + + + client interface shall preserve + + + same as real-mode + + + same as real mode + + +   + + + + + dec + + + client interface shall preserve + + + client interface shall not modify + + + same as real-mode + + + same as real mode + + +   + + + + + Other SPRs + + + client interface shall preserve + + + client interface shall preserve + + + same as real-mode + + + same as real-mode + + + 3 + + + + +
+ Notes: + + + + Only the non-volatile fields ( + cr2-cr4) need to be preserved. + + + + As defined by section 6.3.1. of + . + + + + Other special purpose registers + + + + The + client interface handler shall perform the service + specified by the contents of the argument array that begins at the + address in + r3, place the return value (indicating success or + failure of the attempt to invoke the client interface service) back into + r3, and return to the + client program. This is typically done by a Branch + to Link Register ( + blr). + The + client interface handler shall preserve the contents + of the Stack Pointer (r1), TOC Pointer (r2), Condition Register ( + cr) all non-volatile registers (r13-r31) and all + special purpose registers except lr, ctr and xer. + The preservation of r2 allows TOC-based client programs to function + correctly. OF shall + not depend upon whether its client is TOC-based or + not. If the client interface handler, itself, is TOC-based, it must + provide for the appropriate initialization of its + r2. + +
+ +
+ +
+ Client Program Requirements + +
+ Load Address + + The client’s load address is specified by the value of the + load-base Configuration Variable. The value of + load-base defines the default load address for + client programs when using the + load method. + Load-base shall be a real address in real mode or a + virtual address in virtual mode. Note that this address represents the + area into which the client program file will be read by + load; it does not correspond to the addresses at + which the program will be executed. All of physical memory from + load-base to either the start of OF physical memory + or the end of physical memory, whichever comes first, shall be available + for loading the client program. + +
+ +
+ Initial Program State + This section defines the “initial program state”, the + execution environment that exists when the first machine instruction of a + + client program of the format specified above begins + execution. Many aspects of the “initial program state” are + established by + init-program, which sets the + saved program state so that subsequent execution of + go will begin execution of the + client program with the specified environment. + +
+ Initial Register Values + Upon entry to the client program, the following registers shall + contain the following values: + + + Initial Register Values + + + + + + + + + + + Register(s) + + + + + Value + + + + + Notes + + + + + + + + msr + + + EE = 0, interrupts disabled + + + 1 + + + + +   + + + PR = 0, supervisor state + + +   + + + + +   + + + FP = 1, floating point enabled + + +   + + + + +   + + + ME = 1, machine checks enabled + + +   + + + + +   + + + FE0, FE1 = 0, floating point exceptions disabled + + +   + + + + +   + + + IP, see + + + +   + + + + +   + + + IR,DR, see + + + +   + + + + +   + + + SF=0, 32-bit mode + + +   + + + + +   + + + ILE,LE, little endian support + + + 2 + + + + + r1 + + + See + + + +   + + + + + r2 + + + 0 + + + 3 + + + + + r3 + + + reserved for platform binding + + + 4 + + + + + r4 + + + reserved for platform binding + + + 4 + + + + + r5 + + + See + + + +   + + + + + r6, r7 + + + See + + + +   + + + + + Other user mode registers + + + 0 + + +   + + + + +
+ + Notes: + + + + + OF will typically require the use of external interrupts for its + + user interface. However, when a + client program is invoked, external interrupts shall + be disabled. If a + client program causes the invocation of the user + interface, external interrupts + may be re-enabled. + + + + The 601 processor uses a different mechanism for controlling the + endian-mode of the processor. On the 601, the LE bit is contained in the + HID0 register; this bit controls the endian-mode of both program and + privileged states. + + + + OF does not make any assumptions about whether a client program + is TOC-based or not. It is the responsibility of the client program to + set + r2 to its TOC, if necessary. + + + + As defined in the relevant section of the platform + binding. + + + +
+ +
+ Initial Stack + + Client programs shall be invoked with a valid stack pointer ( + r1) with at least 32 KB of memory available for + stack growth. The stack pointer shall be 16-byte aligned, reserving + sufficient room for a linkage area (32 bytes above the address in r1). If + the system is executing in Real-Mode, the value in r1 is a real address; + if in Virtual-Mode, the address in r1 is a mapped virtual address. + +
+ +
+ Client Interface Handler Address + + When client programs are invoked, + r5 shall contain the address of the entry point of + the + client interface handler. If the system is executing + in Real-Mode, the value in r5 is a real address; if in Virtual-Mode, the + address in r5 is a mapped virtual address. + + Note: This address points to the first instruction of + the + client interface handler, not to a procedure + descriptor. + +
+ +
+ Client Program Arguments + + The calling program + may pass to the client an array of bytes of arbitrary + content; if this array is present, its address and length shall be passed + in registers + r6 and + r7, respectively. For programs booted directly by + OF, the length of this array is zero. Secondary boot programs may use + this argument array to pass information to the programs that they + boot. + + Note: The OF standard makes no provision for + specifying such an array or its contents. Therefore, in the absence of + implementation-dependent extensions, a client program executed directly + from an OF implementation will not be passed such an array. However, + intermediate boot programs that simulate or propagate the OF client + interface to the programs that they load can provide such an array for + their clients. + + Note: + boot command line arguments, typically consisting of + the name of a file to be loaded by a secondary boot program followed by + flags selecting various secondary boot and OS options, are provided to + client programs via the + “bootargs” and + “bootpath” properties of the + /chosen node. + +
+ +
+ +
+ Caching + + The caches of the processor shall be enabled when the client + program is called. The I-cache shall be consistent with the D-cache for + all memory areas occupied by the client program. Memory areas allocated + on behalf of the client program shall be marked as cacheable. Accesses to + “I/O” devices (especially, to devices across + “bridges”) shall be made with the register access words + (e.g., + %rl@). All processors in a SMP system shall have the + same consistent view of all memory areas (for data references). No more + than one processor shall have a modified copy of the same data area in + its cache when the client program is called. + + Note: If firmware makes cacheable M=0 data references + from different processors on a SMP system, it may have to perform + additional cache management to meet this requirement. + +
+ +
+ Interrupts + + OF requires that interrupts be “vectored” to its + handlers when it is in control of the processor; this will occur when the + User Interface is running. Client Interface calls are considered to + execute in the environment of the client, and hence, OF does not assume + ownership of interrupts. + + Note: There used to be a paragraph here that said an + area of memory was to be reserved by the client program for the exclusive + use of OF. This requirement has been removed, since the sharing of + interrupt vectors on these platforms has not been found to be + practical. + OF shall save and restore the first location of each interrupt that + it wants to “take over”. I.e., whenever OF needs the use of + an interrupt, it shall save the current contents of the corresponding + entry point and replace that location with a branch to its entry point. + When OF returns control, it shall restore the RAM location to its + original contents. + +
+ +
+ Client callbacks + + This section defines the callback mechanism that allows OF to + access services exported to it by the client program. As described in + section 6.3.2 and the glossary entries for + callback and + $callback in + , the callback mechanism + follows the same rules as those of Client interface calls. I.e., an + argument array is constructed by OF and the address + of that array is passed (via + r3) to the client’s callback routine; the + address of the callback routine is supplied to OF by means of the + set-callback client call. + If the system is running in Real-Mode, the address of the client + callback routine shall be a real address; if it is running in + Virtual-Mode, the client callback routine address shall be a mapped + virtual address. + +
+ Real-Mode physical memory management assist + callback + + Once the control of physical memory is transferred to the client + program, OF which is running in real-mode shall use the callback service + provided by the client program to allocate physical memory. Client + programs which expect OF to operate in read-mode must implement the + following physical memory management client callback routines for + OF: + + + + alloc-real-mem + + IN: [address] min_addr, [address] max_addr, size, mode + OUT: error, [address] real_addr + This routine allocates a contiguous physical memory of + size bytes within the address range between + min_addr and + max_addr. The + mode parameter contains the WIMGxPP bits as defined + in + A non-zero error code shall be + returned if the mapping cannot be performed. If error code is zero (i.e. + allocation is succeeded) the routine returns the base address of the + physical memory allocated for OF. + + + + +
+ +
+ Virtual address translation assist callbacks + + As mentioned in + , when OF is in Virtual-Mode, + client programs that take over control of the system’s memory + management must provide a set of callbacks that implement MMU functions. + This section defines the input arguments and return values for these + callbacks. The notation follows the style used in chapter 6 of the OF + specification + . + + + + map + + IN: [address] phys, [address] virt, size, mode + OUT: throw-code, error + This routine creates system-specific translation information; this + will typically include the addition of PTEs to the HTAB. If the mapping + is successfully performed, a value of zero shall be placed in the + error cell of the argument array; a non-zero error + code shall be returned in + error if the mapping cannot be performed. + + + + + unmap + + IN: [address] virt, size + OUT: throw-code + The system removes any data structures (e.g., PTEs) for the virtual + address range. + + + + + translate + + IN: [address] virt + OUT: throw-code, error, [address] real, mode + The system attempts to compute the real address ( + real) to which the virtual address ( + virt) is mapped. If the translation is successful, a + PTE shall be placed into the HTAB for this translation, the number of + return cells shall be four with the resulting real address returned in + real and + error shall be set to + false (0). If the translation is not successful, the + number of return cells shall be two and + error shall be set to a non-zero error code. + This call shall be made when OF handles a DSI/ISI within the User + interface. A successful result of the translate call indicates that OF + can complete the interrupted access; a failure indicates that an access + was made to an invalid address. + + + + +
+ +
+ +
+ +
+ User Interface Requirements + + An implementation of OF for the PA shall conform to the core + requirements as specified in + and the following PA-specific + extensions. + +
+ Machine Register Access + + The following + user interface commands represent PA registers within + the + saved program state. Executing the command returns + the saved value of the corresponding register. The saved value may be set + by preceding the command with + to; the actual registers are restored to the saved + values when + go is executed. + The following command displays the PA processor's + saved program state. + + .registers + + +
+ Branch Unit Registers + + + + %cr + + Access saved copy of Condition Register. + + + + + %ctr + + Access saved copy of Count Register. + + + + + %lr + + Access saved copy of Link Register. + + + + + %msr + + Access saved copy of the low order 16 bits of SRR1 register. + + + + + %srr0 and + %srr1 + + Access saved copy of Save/Restore Registers. + + + + + %pc + + An alias of “ + %srr0 ” + + + + +
+ +
+ Fixed-Point Registers + + + + %r0 through + %r31 + + Access saved copies of fixed-point registers. + + + + + %xer + + Access saved copy of XER register. + + + + + %sprg0 through + %sprg3 + + Access saved copies of SPRG registers. + + + + +
+ +
+ Floating-Point Registers + + Unlike the other registers, the floating point unit registers are + not normally saved, since they are not used by OF. The following access + words, therefore, access the registers directly. + + + + %f0 through + %f31 + + Access floating point registers. + + + + + %fpscr + + Access Floating Point Status and Control Register. + + + + +
+ +
+ +
+ +
+ Configuration Variables + + In addition to the standard Configuration Variables defined by the + core OF document + , the following Configuration + Variables shall be implemented for the PA: + + + + “little-endian?” + + This boolean variable controls the endian-mode of OF. If + true (-1), the endian-mode is Little-Endian; if + false (0), the endian-mode is Big-Endian. The default + value is implementation dependent. + + + + + “real-mode?” + + This boolean variable controls the address translation mode of OF. If + true (-1), the addressing mode is Real-Mode; if + false (0), the addressing mode is Virtual-Mode. The + default value is implementation dependent. + + + + + “real-base” + + This integer variable defines the starting physical address to be + used by OF. + + + + + “real-size” + + This integer variable defines the size of the physical address space + which can be used by OF. + + + + + “virt-base” + + This integer variable defines the starting virtual memory address + which can be used by OF. + + + + + “virt-size” + + This integer variable defines the size of the virtual address space + which can be used by OF. + + + + + “load-base” + + This integer variable defines the default load address for + client programs when using the + load method. The default value is implementation + dependent. + + + + +
+ +
+ MP Extensions + + This section specifies the application of OF to PA multiprocessor + (MP) systems. An OF implementation for an MP PA system shall implement the + extensions described in this section as well as the requirements described + in previous sections of this binding. + +
+ The Device Tree + + This section defines an additional property under the + /chosen node for a MP extension. Refer to + for more details about the + device tree structure for a MP Configuration. + +
+ Additional Properties + + /chosen Node Properties + + + + “cpu” + + property name, identifies the running CPU. + prop-encode-array: An integer, encoded as with + encode-int, which contains the i-handle of the CPU + node that is associated with the “running” CPU. + + + + + +
+ +
+ +
+ Initialization + + OF shall select one processor, using an algorithm of its choice, to + be the “master” processor, which performs the role of the + single processor on a uniprocessor system, either booting the client or + providing the user interface. OF shall place all the remaining processors + into stopped state, a state in which the processor does not perform OF or + client functions and does not interfere with the operation of the master + processor. A processor in stopped state remains in that state unless and + until an executing client starts it using the + start-cpu client service defined below. + Client programs shall use the OF + start-cpu client interface service to start all + processors before it reclaims the OF memory + On machines in which a machine check on one processor is broadcast + to all processors, the processors which are either in the idle or stopped + state shall not change their states due to a machine check on another + processor: OF shall not depend on the contents of the low vector (IP=0) + in the event of a machine check. + + depicts the relationship of the + Running, Stopped and Idle States to each other. The + Client Interface Service calls are shown as how to + move between the states. + +
+ Stopped, Running, and Idle State Diagram + + + + + + + + +
+ + Note: OF's memory cannot be reclaimed by a client if + a CPU is in the “stopped” or “idle” state. + +
+ +
+ Client Interface Services + + The following client interface services are added for MP support on + PA systems. These interfaces make the client program responsible for any + Inter-CPU communication needed for these interfaces. The rationale for + this is to architecturally separate the Inter-CPU communication mechanism + of the firmware from the client program and vice versa. + + + + start-cpu + + IN: nodeid, pc, arg + OUT: none + This client interface service starts the CPU. The + nodeid is the phandle of a node whose device_type is + “cpu”. + Start-cpu arranges for the CPU identified by phandle + in nodeid to begin executing client code at the real + address given by the + pc input with an argument, + arg, passed in register r3. When it begins execution, + the started processor shall be in the endian mode of the client program, + and in real (not translated) addressing mode. The contents of registers + other than r3 are indeterminate. + A client should not call + start-cpu for the processor on which it is running, + effectively restarting with a new pc and abandoning the only client + thread. A jump or branch instruction shall be used instead to achieve the + objective. + start-cpu permits more than one processor to run at + the same time, enabling multi-threaded client execution. In general, an + OF client shall avoid multi-threaded operation within OF. Usually, this + means that client threads running on different CPUs must use mutual + exclusion to prevent more than one processor from making client service + requests at any one time. The exceptions are that a client thread may + invoke either the + stop-self or + idle-self client services defined below at any + time. + Note: The results are undefined if the CPU identified + by *phandle* has already been started (e.g. it is already running and has + not exited) or *phandle* is not a valid package handle of a CPU device + node. + + + + + stop-self + + IN: none + OUT: none + OF places the processor on which the caller was running into the + “stopped” state. The client program is not-resumable. + Note: When an MP client program exits, one CPU + invokes the + exit client interface service, the others invoke the + stop-self service. + + + + + idle-self + + IN: none + OUT: none + OF places the CPU on which this service was invoked into an 'idle' + state, saving the *current state* of the client program, so that the + client program may be resumed. + A processor in idle state can be resumed using + resume-cpu service defined below or restarted using + start-cpu. If the processor is resumed, it executes + a normal return to the client, as if its call to + idle-self had just completed. + + Note: When a client program wants to enter the + firmware user interface, one CPU invokes the + enter client interface service, the others invoke the + idle-self service. The rational is that the user + interface may affect the machine state in any way that it desires, + therefore the client shall not depend on it. + + + + + resume-cpu + + IN: nodeid + OUT: none + This client interface service is used to resume an *idled* CPU. The + nodeid is the phandle of a CPU node in idle + state. + resume-cpu arranges for that CPU to restore the + CPU’s state as saved by + idle-self and begin return to the client, completing + the idle-self client service call that placed the CPU into idle state. + The results are undefined if the CPU identified by *phandle* is not in an + *idle* state by a previous call to the + idle-self client interface service. + Note: When the client program is resumed via the GO + (or similar) user interface command, the client program is resumed on the + CPU which called the + enter service; the client program is responsible for + calling the + resume-cpu service to resume other idled CPU's, if + that is the desired client program behavior. + + + + +
+ +
+ Breakpoints + + If the breakpoint is taken by the firmware, without the client + program's assistance, the other CPUs will continue to run in the client + program. The client program may field the breakpoint 'trap' or 'vector' + and idle the other CPUs before entering the PROM. The platform binding + document has to specify how this is done to avoid loss of state at + breakpoint time. + +
+ +
+ Serialization + + The firmware is a single threaded program, from the client + program's point of view. Only the + idle-self, + stop-self, + enter and + exit client interfaces may be invoked simultaneously + on different CPUs. Furthermore, only a single CPU may invoke the + enter or + exit client interface at any one time. The other CPUs + must use the + idle-self or + stop-self client interface service. + + Note: The results are undefined if the client program + invokes client interface services including breakpoint traps (other than + the + enter/exit stop-self/idle-self case listed above) + simultaneously on more than a single CPU. + + Note: Since locking mechanisms are subject to client + program policy, the client program is responsible for implementing any + necessary mechanism to insure that it adheres to this policy. Further, + the client program should disable any preemption mechanism before calling + a client interface service to avoid rescheduling a thread of execution in + the firmware on a different CPU if such a mechanism exists in the client + program. + +
+ +
+ + diff --git a/DeviceTree/ch_devtree_system.xml b/DeviceTree/ch_devtree_system.xml new file mode 100644 index 0000000..206cf68 --- /dev/null +++ b/DeviceTree/ch_devtree_system.xml @@ -0,0 +1,10452 @@ + + + + System Binding + +
+ LoPAR Boot Flow + + This section gives a system boot process overview and defines the + enhancements to the standard OF boot process that are present in the boot + process for an LoPAR platform. + +
+ Boot Overview + The platform performs a normal OF boot (see + , as stated in the Core + Practice Document, Section 4.2.3, Start-up script evaluation. LoPAR + platforms provide an additional capability to assist the user in choosing + which of several OSs to boot. A key sequence can be used to interrupt the + normal boot flow and present the user with a + multiboot menu, which can be either graphical or + text-based at the discretion of the platform’s firmware, from which + the user can choose one of the installed or installable OSs. Presenting + the user with this choice can also be made the default mode of operation + at platform boot time, by means of the + auto-boot? and + menu? configuration variables. + An overview of a platform boot sequence and the additions of the + multiboot menu are given below: + + + + + + + + + + + + + The boot flow described above occurs after all of the devices have + been probed (i.e., by the execution of + probe-all); see + additional requirements for + probe-all method. + The boot sequence defaults to a normal boot if the boolean variable + + auto-boot? is true and + diagnostic-mode? is false. In this situation, the + system shall then boot from information contained in the configuration + variables + boot-device and + boot-file. + From the boot sequence above, entry to the + multiboot menu may occur anywhere after step ‘f’, + banner, if the platform key + sequence (multiboot menu) has been depressed or in step + ‘i’ if the boolean variable + menu? is true. + +
+ Additional Requirements for probe-all Method + + Before probing for plug-in devices, OF shall execute the + probe method, as with + execute-device-method, of any built-in device nodes. + The order of evaluation shall ensure that the + probe method of a parent device node is executed + before the + probe method of any of its children. + + Note: During this built-in probing, /rom nodes will + locate ROM based OSs. The FCode for these devices can publish their + “bootinfo” properties that are used + during the multiboot scenario as described below. + +
+ +
+ LoPAR Multiboot + + The boot choices identified to the user are defined by + bootinfo objects hich are located on various system + media. Each + bootinfo object contains information about one OS, + such as its name and description, an icon depicting it, and an OF command + sequence to load and execute it. The locations where + bootinfo objects can be found are specified by OF + device-specifiers that are the values of + configuration variables, the names of which are of the form + “bootinfo-nnnnn”, where + “nnnnn” is OS-specific. These + configuration variables are stored in the System + Partition in NVRAM and are published in the + device tree as properties under the + /options node. The + multiboot menu will use these + configuration variables to locate and parse + bootinfo to obtain the OS icon, description, + etc. + In addition to the + bootinfo-nnnnn configuration variables, the + multiboot menu will search the device tree for nodes + containing + “bootinfo” properties, which specify that + the node can supply a + bootinfo object. This is particularly useful for OSs + contained in ROMs. + + Note: The order prescribed by probe-all guarantees + that these properties be created before the + multiboot menu has been invoked. + Different versions of the same OS may each have their own + bootinfo and associated + configuration variables. Although it is possible to + put + bootinfo in any media location that OF can read, this + specification defines standard locations for various types of media, to + allow the firmware to establish the + bootinfo configuration variables automatically in + many cases. + +
+ +
+ Bootinfo Configuration Variables + + A + bootinfo configuration variable is any + configuration variable that meets the following + requirements: + + + + Its name is of the form + “bootinfo-nnnnn”, where + nnnnn is a string of at most 22 characters from the + set of valid characters for OF configuration variable names. The exact + value of + “nnnnn” for a particular OS may be chosen + by that OS. The naming convention for the OS should be chosen to avoid + possible naming conflicts between OS vendors. + + + + Its value is an OF + device-specifier that identifies an object (e.g. disk + file, tape file, disk partition or + /rom child node) whose contents are a + “bootinfo object” as defined + below. + + + +
+ +
+ Bootinfo Properties + + Any node in the device tree can have a + “bootinfo” property whose value specifies + the arguments to use in opening that device in order to access its + bootinfo object. + + “bootinfo” S + + property name locates the node’s + bootinfo object + + prop-encoded-array: A string, encoded as with + encode-string + The presence of this property signifies that the device has an + associated + bootinfo object. The value is a text string such + that when this device’s node + open method is called, the value of text string that + is passed to the device’s node + open method is + “my-args”. When so opened, subsequent + calls to the node’s + “read” method will yield the contents of + the node’s + bootinfo object. + +
+ +
+ Standard Locations for Bootinfo Objects + + The standard locations for + bootinfo objects on various LoPAR media and + partition types is shown in the table below. An OS must put its + bootinfo object in the standard location in order to + guarantee interoperability with the LoPAR + multiboot menu mechanism. + + + Standard Pathnames for + <emphasis>bootinfo.txt</emphasis> File + + + + + + + + + + Name + + + + + Device/Partition + + + + + Notes + + + + + + + + Installation Media: + + +   + + +   + + + + + Any block device: + + + device:partition,\ppc\bootinfo.txt + + + Any file system format + + + + + Tape: + + + device:0 (Note 1) + + + Presence of bootinfo.txt is optional + + + + + ROM: + + + device:bootinfo + + + bootinfo is the value of the “ + bootinfo ” property in a /rom child + node + + + + + Network: + + + Could specify bootinfo.txt or some other file from the + Bootp server + + + Specifying bootinfo.txt from the Bootp server is + optional + + + + +
+ + Note 1: If bootinfo.txt file is not present, file 0 + should contain a program image file for a bootable tape. + Example of installed ( + “bootinfo-nnnnn”) block device + (disk): + ALIAS EXAMPLE: + bootinfo-aix-4.3=disk:2 (The contents of partition 2, which is + probably a “0x41” partition, on the default disk, is the + bootinfo.txt file for a version of the AIX + OS.) + bootinfo-nt-4.0=disk:\os\winnt\bootinfo.txt + NON-ALIAS EXAMPLE: + bootinfo-aix-4.4=/pci@ff500000/pci3,1000@10/sd0,0:3 (The contents + of partition 3, which is probably a “0x41” partition, on the + SCSI disk at target 0 unit 0, is the + bootinfo.txt file for a version of the AIX + OS.) + +
+ +
+ Bootinfo Objects + + The information used by OF to display information in the + multiboot menu and to + locate and process an OS load image is contained + within a sequence of text that is called a + bootinfo object. The text comprising the bootinfo + object uses SGML syntax, as defined in + , with tags identifying the + subordinate elements. + The following outline is a summary of the organization of the + bootinfo object. Elements at the same level do not + have any required order. The tags are illustrated in upper case, but + shall be processed in a case-insensitive manner. + + + .... + + + .... + + + .... + + + + hh hh hh hh . . . + + +]]> + + + Notes: + + + + + If ‘SIZE’ is not present, assume default of 64,64. + If ‘COLOR-SPACE’ is not present, assume default of + 3,3,2. + + + + Another <chrp-boot> tag sequence could define a different + boot selection + + + + LoPAR platforms will recognize only the tags between the + beginning <chrp-boot> tag until the end </chrp-boot> tag. If + a tag is unrecognized, the material will be ignored until the end tag. + Other non-<chrp-boot> tags may be supported in the future. These + additional selections would also be presented to the user as boot + options. + + + +
+ Bootinfo Entities + + SGML provides “entities” that provide symbolic names + for text. When the entity names are contained within & and + ‘;’, the entity is replaced with text as defined by the + entity; i.e., entities provide a “macro” substitution + capability. The + bootinfo object may use entities to supply pathname + components that depend upon the location of the file. Also, entities have + been defined for the standard SMGL Tags for the presence of the + ‘<‘, ‘&’ and ‘>’ characters + in the text as &lt;, &amp; and &gt;. Within the + <BOOT-SCRIPT> element, the following entities are defined with + respect to the fully qualified pathname of the + bootinfo object: + + + + device + + the device component. + + + + + partition + + the partition component. + + + + + directory + + the directory component. + + + + + filename + + the filename component. + + + + + full-path + + the entire fully qualified pathname. + + + + + The fully qualified pathname could be represented by the following + text: + + + Note: Underlined portions illustrate where entities + are positioned within the full pathname. +
+ +
+ Bootinfo Character Sets + The character set used by the bootinfo.txt file is ISO-8859-1 + (Latin-1). Element tags and entity names are not case sensitive; all + other text is case sensitive. +
+ +
+ Element Tag Descriptions + The following sections describe each of the element tags and how + they are used. +
+ +
+ CHRP-BOOT Element + This element provides the grouping for each OS that is represented + within a single bootinfo.txt file. Multiple CHRP-BOOT sections are + allowed within a single bootinfo.txt file. +
+ +
+ OS-NAME element + This element contains the complete name of the OS. +
+ +
+ BOOT-SCRIPT element + This element contains an OF script that is executed when the OS + defined by this CHRP-BOOT section is selected to be loaded. Each line of + this element is processed as if it were entered from the input device of + the user interface. Typically, the last line of this script would contain + a + boot command; the pathname of the OS’s load + image can be constructed with the entities described above. +
+ +
+ ICON element + This element describes the OS icon that can be displayed by the + multi-boot process. The icon should be designed to be pleasant against a + light background. + The SIZE parameter consists of a two decimal numbers, separated by + a comma, that represent the width and height (in pixels) of the icon, + respectively. The default value is “64,64” + The COLOR-SPACE parameter consists of three decimal numbers, + separated by commas, that represent the number of bits for the red, + green, and blue components of each pixel. The default value is + “3,3,2”1. + + Note 1: This version of LoPAR supports only a 3,3,2 + icon color-space and 64,64 icon size. Other icon size’s and + color-space’s are reserved for future implementations. + If an icon is not stated, the platform will display a generic + system icon that is platform dependent. + +
+ BITMAP element + This element specifies the bitmap. It consists of a sequence of hex + digit pairs, each of which defines a pixel; white spaces is allowed + between pixel values. The number of hex digit pairs is defined by the + product of the width and height values of the SIZE parameter. + + + + icon string example: + + <icon size=64,64 + color-space=3,3,2><bitmap>hh hh... + hh2</bitmap></icon> + + + + + + Note 2: Hex string would be 8192 characters for a + size=64,64 in the above example. + For the two examples below, the tags have been indented and + separated by line feeds for each start/end tag pair to make a more + readable script style. + + + AIX Bootinfo Object Example: + + + AIX 4.2.D.0 + AIX 4.2.D.0 + boot &device;:2 + hh ... hh1 +]]> + + AIX Diagnostics Bootinfo Object Example: + + AIX 4.2.D.0 Diagnostics + AIX 4.2.D.0 Diagnostics + boot &device;:2 diag + hh ... hh +]]> + + + Note: 64x64 icon size would have 8192 hex string + characters in the "hh ... hh" field above. +
+ +
+ +
+ +
+ Multiboot Menu + If the boot sequence is interrupted by the multiboot key sequence, + then the firmware shall present a + multiboot menu that provides at least the functions + listed below. The form of the menu (e.g. graphical or text- oriented) and + the selection mechanism (e.g. numbered choices, arrow keys, or mouse) are + platform-dependent. + Multiboot Required Functions: + + + + Locate all bootinfo objects specified by bootinfo configuration + variables and device node + “bootinfo” properties. For each + bootinfo object, present a choice corresponding to + each valid <chrp-boot> section contained therein. For each such + choice, allow the user to either: + + + + Execute the contents of that + bootinfo object’s <boot-script> + element. + + + + Set the + boot-command configuration variable to the contents + of that + bootinfo object’s <boot-script> + element. + + + + + + Present a choice corresponding to each install device, which, + when invoked, will attempt to locate a bootinfo object at the + device’s standard location (see Table 1). + + + + Allow the user to manage configuration variables + + + + Allow the user to invoke the OF user interface + + + + Additional options that could be implemented would be to provide a + means to get to diagnostics or specific platform options. + There shall be at least one key sequence to enter the multi-boot + platform function for an LoPAR platform. + + Note: OS have the responsibility to update the NVRAM + System Partition Variable to reflect a change where the + bootinfo.txt file is located; e.g., moving to a + different disk device. Also, the OS is responsible for maintaining the + contents of the + bootinfo.txt file. + +
+ +
+ +
+ Reboot-Command Variable Description + + The OS can cause OF to execute a specified sequence of commands at + the next boot by setting the value of the + reboot-command configuration variable. LoPAR + firmware implementations shall implement the following configuration + variable. + + + + reboot-command(-- addr len) [N] + + One time or temporary reboot command. + The value of this configuration variable is a string consisting of + zero or more lines of text, with lines separated by either + <return>, <linefeed>, or + <return><linefeed>. + During firmware start-up, just prior to checking the + auto-boot? configuration variable for automatic + booting, the firmware shall check the value of + reboot-command. If the value is not the empty + string, the firmware shall save the value to a temporary location, set + reboot-command to the empty string, and evaluate the + saved value as though it were a series of user interface command + lines. + If the evaluation of + reboot-command returns without executing, the + firmware shall proceed with its normal start-up sequence. In typical + usage, however, the value of + reboot-command will include a + boot command that starts a client program and does + not return. + + + + +
+ +
+ +
+ LoPAR Processor + + OF defines a minimum cell size of 32 bits; therefore, only one cell + is necessary to represent addresses up to 4GB (32 bits). Two cells are + necessary to represent addresses above 4GB and within 64 bits. Also, two + cells are necessary to represent sizes greater than 4GB. + +
+ Processor Endian-ness Support + LoPAR requires the use of PA processors that support Big-Endian + storage format. LoPAR allows for the use of PA processors that support + Little-Endian storage format in addition to Big-Endian storage + format. +
+ +
+ Multi-Threading Support + + The processors used in some platforms support multiple threads of + execution. This processor model differs from Symmetric Multi-Processors + in that the multiple threads of execution share the processor hardware to + such an extent that operations on one thread can significantly affect the + performance of another tread of the same processor. Therefore, the + processor is represented with a single processor node having multiple + interrupt server numbers. The OS is then free to start and stop + multi-threading as the processing environment dictates. The client + interface call + start-cpu, operates on the full CPU as presented in + the device tree, upon successful completion, the started CPU is running + in single threaded mode, the active thread being the one associated with + the first interrupt server number in the + “ibm,ppc-interrupt-server#s” property. + The client interface calls: + stop-self, idle-self, resume-cpu are all defined to + operate on the full CPU when called in single threaded mode, the behavior + of these calls if called with multiple threads active is implementation + dependent, it is suggested that the implementation deactivate all but one + thread before performing the call’s standard function. + +
+ +
+ +
+ OF Platform Extensions + This section defines OF properties, methods, device tree structure + and Client Interface Service requirements for LoPAR platforms. + The naming conventions for IBM unique OF properties and devices are + as follows: + + + + Properties created for use only by IBM compatible implementations + must have the string + “ibm,” as a prefix to the property + name. + + + + Property names prefixed with the string + “ibm,fw-” are reserved for and must be + controlled by the Firmware Area. + + + + An IBM property name which does not have the firmware or AIX prefix + must be defined in this document unless documented elsewhere. + + + + The value of a device + “name” whether reported through the + compatible property or name property for a device implemented by IBM must + contain the string + “IBM,” as a prefix unless it conforms to a + binding which specifies otherwise. + + + +
+ Properties for Dynamic Reconfiguration + + The following standard properties are define for all dynamically + reconfigurable platform nodes. + + + + “ibm,drc-indexes” + + + property name denotes an integer index to be used to + communicate to the firmware what connector is to be operated upon for the + various RTAS calls used for DR. + + prop-encoded-array: An integer encoded as with + encode-int, followed by a list of integers also + encoded as with + encode-int. + For each DR connector, a unique integer index is provided which + uniquely identifies the DR connector for purposes of the + ibm,configure-connector, + set-indicator, and + get-sensor RTAS calls. The first element of the array + is the number of connectors associated with the node. The second element + of the array is the index which represents the first connector associated + with the node, the third element the second connector, and so on until + all of the node’s DR connectors are specified. + + + + + “ibm,my-drc-index” + + + property name denotes an integer index (value of the + entry in the + “ibm,drc-indexes” property) for the + connector between the node and the node’s parent. + + prop-encoded-array: An array of integers encoded as + with + encode-int. + + + + + “ibm,drc-names” + + + property name describes the external labeling of the + DR connectors. + + prop-encoded-array: An integer encoded as with + encode-int, followed by a list of strings each + encoded as with + encode-string. + For each DR connector, a unique human-readable name for a + connector. The first element of the array is the number of connectors + associated with the node. The second element of the array is the + human-readable name which represents the first connector associated with + the node, the third element the second connector, and so on until all of + the node’s DR connectors are specified. + + + + + “ibm,drc-power-domains” + + + property name gives the power domain number for each + connector associated with the node, which is the domain number to be used + in the + set-power-level RTAS call, if necessary. + + prop-encoded-array: An integer encoded as with + encode-int, followed by a list of integers also + encoded as with + encode-int. + For each DR connector, the power domain which will be controlled + for DR operations (the power domain in which the DRC resides), and which + will be used, if not -1, in the + set-power-level RTAS call for the connector. The + power domain number of -1 denotes a live-insertion power domain (in which + case, the + set-power-level RTAS call is not used). The first + element of the array is the number of connectors associated with this + node. The second element represents the domain number for the first + connector. The element following this is the domain number for the second + connector, and so on until all of the node’s DR connectors are + specified. + + + + + “ibm,drc-types” + + + property name, describes the type of each connector + associated with the node, in a human-readable form. + + prop-encoded-array: An integer encoded as with + encode-int, followed by a list of strings each + encoded as with + encode-string. + The first element of the array is the number of connectors + associated with this node. The second element of the array is the + connector type of the first connector associated with the node, the third + element the second connector, and so on until all the node’s DR + connectors are specified, and these elements will be one of the currently + defined connector types specified in + . + + + Currently Defined DR Connector Types + + + + + + + + Connector Type(character + string) + + + + + Description + + + + + + + + 1 + + + A 32-bit, 5 Volt conventional PCI slot which accommodates + cards that operate up to 33 MHz Only. + + + + + 2 + + + A 32-bit, 5 Volt conventional PCI slot which accommodates + cards that operate up to 33 MHz. + + + + + 3 + + + A 32-bit, 3.3 Volt conventional PCI slot which + accommodates cards that operate up to 33 MHz Only. + + + + + 4 + + + A 64-bit, 5 Volt conventional PCI slot which accommodates + cards that operate up to 33 MHz Only. + + + + + 5 + + + A 64-bit, 5 Volt conventional PCI slot which accommodates + cards that operate up to 33 MHz. + + + + + 6 + + + A 64-bit, 3.3 Volt conventional PCI slot which + accommodates cards that operate up to 33 MHz Only. + + + + + 7 + + + A 32-bit, 3.3 Volt conventional PCI slot which + accommodates cards that operate up to 66 MHz. IOAs that operate + up to 66 MHz will only operate at frequencies above 33 MHz if + there are no 33 MHz IOAs on the same bus. + + + + + 8 + + + A 64-bit, 3.3 Volt conventional PCI slot which + accommodates cards that operate up to 66 MHz. IOAs that operate + up to 66 MHz will only operate at frequencies above 33 MHz if + there are no 33 MHz IOAs on the same bus. + + + + + 9 + + + Reserved + + + + + 10 + + + Reserved + + + + + 11 + + + A 32-bit PCI-X capable slot which accommodates cards that + operate up to 66 MHz + + + + + 12 + + + A 32-bit PCI-X capable slot which accommodates cards that + operate up to 100 MHz + + + + + 13 + + + A 32-bit PCI-X capable slot which accommodates cards that + operate up to 133 MHz + + + + + 14 + + + A 64-bit PCI-X capable slot which accommodates cards that + operate up to 66 MHz + + + + + 15 + + + A 64-bit PCI-X capable slot which accommodates cards that + operate up to 100 MHz + + + + + 16 + + + A 64-bit PCI-X capable slot which accommodates cards that + operate up to 133 MHz + + + + + 17 + + + A 64-bit PCI-X capable slot which accommodates cards that + operate up to 266 MHz + + + + + 18 + + + A 64-bit PCI-X capable slot which accommodates cards that + operate up to 533 MHz + + + + + 19 + + + A PCI Express Rev 1 slot with 1x lanes. + + + + + 20 + + + A PCI Express Rev 1 slot with 2x lanes. + + + + + 21 + + + A PCI Express Rev 1 slot with 4x lanes. + + + + + 22 + + + A PCI Express Rev 1 slot with 8x lanes. + + + + + 23 + + + A PCI Express Rev 1 slot with 16x lanes. + + + + + 24 + + + A PCI Express Rev 1 slot with 32x lanes. + + + + + 25 + + + A PCI Express Rev 2 slot with 1x lanes. + + + + + 26 + + + A PCI Express Rev 2 slot with 2x lanes. + + + + + 27 + + + A PCI Express Rev 2 slot with 4x lanes. + + + + + 28 + + + A PCI Express Rev 2 slot with 8x lanes. + + + + + 29 + + + A PCI Express Rev 2 slot with 16x lanes. + + + + + 30 + + + A PCI Express Rev 2 slot with 32x lanes. + + + + + CPU + + + Logical CPU + + + + + MEM + + + Logical Memory Region + + + + + MEM-n + (where n is a + non-zero integer) + + + Extended Logical Memory Region(s). Used with the Reserved + Memory option. + + + + + PHB + + + Logical PCI Host Bridge + + + + + SLOT + + + Logical I/O slot + + + + + PORT + + + Logical Port + + + + +
+ + + + + “ibm,phandle” + + + property name, defines the phandle for the + node. + + prop-encode-array: An integer encoded with + encode-int. + + + + +
+ +
+ OF Root Node + This section defines additional properties and methods associated + with LoPAR platforms that OSs expect to find in the root node. Unit + addresses in an LoPAR system are limited to 60 bits in length + corresponding to the maximum real address supported by the POWER + processor architecture. The unit address of all non-system nodes that are + children of the root node shall have the same value each time the + platform is booted; i.e., shall be invariant for each boot + process. + + Notes: + + + + + This requirement ensures that the PHB would have a stable unit + address. Violations of this rule may require reinstallation of an + OS. + + + + The recommended practice is to generate a virtual unit address + for PHB nodes. This is done by giving a zero length to its first reg + property with an address that is selected such that it remains constant. + In single bridge platforms, the value is chosen based upon historical + precedent of the predecessor product. In multi-enclosure platforms, the + virtual unit address is based upon the manufacturing serial number to + insure uniqueness. + + + +
+ Root Node Properties + + This section defines the additional properties or values which + shall be present in the root node unless otherwise specified. + + + + “#address-cells” [S] + + Standard + property name, encoded as with + encode-int, that specifies the number of cells + required to represent physical addresses on the processor bus. The value + of + “#address-cells” for the processor bus + shall be 1 or 2 depending on whether there is any memory addressable at + or above 4GB’s. + + + + + “#size-cells” [S] + + Standard + property name, encoded as with + encode-int, that specifies the size of cells + required to represent physical addresses on the processor bus. The value + of + “#size-cells” for the processor bus shall + be 1 or 2 depending on whether there is any memory addressable at or + above 4GB’s. + + + + + “clock-frequency” [S] + + Standard + property name, encoded as with + encode-int, that represents the primary system bus + speed (in hertz). + + + + + “ibm,extended-clock-frequency” + + + property name: Property that represents the primary + system bus speed in hertz of this node. This property allows the encoding + of multi-giga-hertz quantities. + + prop-encoded-array: Consisting of two cells + (freq-hi, freq-lo) each encoded as with + encode-int, such that their combined value is + (freq-hi || freq-lo). + + + + + “system-id” [S] + + Standard + property name, encoded as with + encode-string, that contains the identification of + the computer system (Reference the + “name” property in + ). This string should be unique + across all systems and all manufacturers. An example of an address of + this form is “0nnnnnnmmmmmm” where nnnnnn is a sequence of 6 + uppercase hexadecimal digits representing a 24-bit value that identifies + manufacturer and mmmmmm is a sequence of 6 uppercase hexadecimal digits + representing a 24-bit binary number assigned by the manufacturer to + assure uniqueness. + + Note: For platforms with built-in ethernet or other + IEEE 802-style interfaces, the 6-byte MAC address assigned to that + interface meets the requirements and could be used as the + system-id. + + + + + “model” [S] + + Standard + property name that is a printable string identifying + the manufacturer and model number of the platform. + + prop-encoded-array: Text string, encoded as with + encode-string. + The value of this property is a vendor dependent string which + identifies this platform via its manufacturer and model number. + + + + + “device_type” [S] + + Standard + property name that is a printable string identifying + the platform as LoPAR Compliant. + + prop-encoded-array: Text string, encoded as with + encode-string. + The value of this property is a string, + “chrp” which identifies the platform is + LoPAR Compliant. + + + + + “ibm,lpar-capable” + + + property name indicates that the platform is capable + of supporting logical partitioning and is only present on such systems. + This property is, however, present even if the platform is not currently + configured for logical partition operation. + prop-encoded-array: <NULL> + + + + + “ibm,converged-loc-codes” + + + property name indicates that the platform supports + the “Converged Location Code” option. This property shall be + present only on platforms that support the “Converged Location + Code” option. + + prop-encoded-array: <NULL> + + + + + “ibm,max-boot-devices” + + + property name indicates the maximum number of + boot-device entries that the OF automatic boot code will process (entries + after this number are ignored). Platforms that do not present this + property default to process a maximum of 5 entries. + + prop-encoded-array: an integer encoded as with + encode-int. + + + + + “ibm,aix-diagnostics” + + + property name indicates that the platform is capable + running AIX diagnostics. + + prop-encoded-array: <NULL> + + + + + “ibm,diagnostic-lic” + + + property name, presented to partitions authorized to + perform diagnostic operations, that indicates that the platform is + designed to use the specified license internal code package for + diagnostic services. + + prop-encoded-array: one or more encapsulated package + handles encoded as with + encode-int. + + + + + “ibm,io-server-lic” + + + property name indicates that the platform is designed + to use the specified license internal code package for I/O + services. + + prop-encoded-array: one or more encapsulated package + handles encoded as with + encode-int. + + + + + “ibm,plat-res-int-priorities” + + + property name that designates to the client program + that the platform has reserved one or more interrupt priorities for its + own use. + + prop-encoded-value: one or more ( + interrupt priority, range) pairs, where + interrupt priority is a single cell hexidecimal + number between 0x00 and 0xFF, and + range is an integer encoded as with + encode-int that represents the number of contiguous + interrupt priorities that have been reserved by the platform for its + internal use. + + + + + “ibm,eeh-default” + + + property name indicates the platform’s default + setting for the EEH option. + + prop-encoded-array: An integer encoded as with + encode-int that represents the platform’s + default setting for the EEH option. The defined states are: + 0= The platform boots up with the EEH option disabled. + 1= The platform boots up with the EEH option enabled. + + + + + “ibm,model-class” + + property name to indicate the platform class. + prop-encoded-array: string encoded as defined in + . + + + Example Encoding Strings + + + + + + + + + + Encoded String + + + + + Platform Class + + + + + + + + C5 + + + Blade/Entry + + + + + D5 + + + Entry + + + + + E5 + + + Entry + + + + + F5 + + + Mid-range + + + + + G5 + + + High-end + + + + + H5 + + + High-end + + + + + P5 + + + obsolete + + + + +
+ + + + + “ibm,partition-no” [S] + + property name to define the partition number of this particular + logical partition as established by the Hardware Management + Console. + prop-encoded-array: The logical partition number is a one cell + integer encoded as with + encode-int. + + + + + “ibm,partition-name” [S] + + property name to define the partition name of this particular + logical partition as established by the Hardware Management + Console. + prop-encoded-array: A NULL terminated string. + + + + + “ibm,platform-hardware-notification” + + + property name indicating to the OS the presence of + hardware for which the OS may need to take action. This property exists + to notify the OS of hardware elements on the platform which may require + special handling by the OS, such as in response to a hardware + errata. + + prop-encoded-array: An integer encoded as with + encode-int followed by a list of strings encoded as + with + encode-string. + The first element represents the number of strings to follow in the + property. Each string in the array names a hardware element that may + require the OS to take specific action. The intention is that the string + is to name the hardware element being reported. It is not the intention + to define (or even hint at) the action that the OS must take. It is + expected that some source outside this document will contain a cross + reference between these strings and documentation such as hardware errata + notes which define the action the OS must take. + If the + “ibm,platform-hardware-notification” + property is provided and a string begins with the <name> field of the + “name” (see + ) property in the + CPU nodes followed by an underscore, the characters + following the underscore are a hexadecimal representation of the contents + of a Processor Version Register that the platform may contain. + + + + + “ibm,fault-behavior” + + + property name to define the behavior of the Error Log + indicator relative to FRU faults. + + prop-encoded-array: An integer encoded as with + encode-int that represents how the Error Log indicator should be handled + when a FRU fault is detected. + Property non-existent -- The OS may set FRU Fault and Error Log + indicators for all errors (those it detected and those that the platform + reports to the OS). + Property exists with a value of 1 -- The OS only sets FRU Fault and + Error Log indicators for errors it detects. + + + + + “ibm,fru-9006-deactivate” + + + property name to define whether or not the OS should + deactivate 9006 indicators that it has activated. + + prop-encoded-array: An integer encoded as with + encode-int that represents how the OS should behave relative to FRU Fault + indicator deactivation. + Property non-existent -- The OS is responsible for deactivating FRU + level 9006 indicators that it has activated. + Property exists with a value of 1 -- The OS should not deactivate + FRU level 9006 indicators that it has activated, but is allowed to do so + (firmware does not block). The deactivation of the FRU level 9006 + indicators is platform and service procedure dependent. + + + + + “compatible” [S] + + Standard + property name that conveys the platform architecture + identifiers. + + prop-encoded-array: The concatenation, with + encode+, of an arbitrary number of text strings, + each encoded with + encode-string. + Specifies a list of platform architectures with which this platform + is compatible. This is used by a client program when it is trying to + determine the appropriate support for this platform. This property shall + include the substring “LoPAR-<LoPAR + version>-<Manufacturer>-<Manufacturer Version>” + where <LoPAR version> is the text (without blanks) after the word + “Version” on the cover page of the LoPAR specification that + the platform adheres to, <Manufacturer> is a unique string + identifying the manufacturer of the platform (see the OF standard + description of the + “name” property for suggestions), and + <Manufacturer_Version> is defined by the manufacturer of the + platform. + + Note: In order to comply with the OF Standard + description of the + “compatible” property, implementations + should place the “LoPAR-<LoPPR + version>-<Manufacturer>-<Manufacturer Version>” + substring after values that were present in the + “compatible” property prior to the + inclusion of the “LoPAR-<LoPAR + version>-<Manufacturer>-<Manufacturer Version>” + substring. + + + + + “ibm,max-vios-function-level” + + + property name to define the maximum vios function + level that a client shall permit. + + prop-encoded-array: An integer encoded as with + encode-int that represents the maximum VIOS level + that the client shall negotiate. See + for the definition of the + values of this property. + + + + + “ibm,partition-performance-parameters-level” + + + property name to define the level of partition + performance parameter reporting supported by the platform. + + prop-encoded-array: An integer encoded as with + encode-int that represents the level of partition performance parameter + reporting supported by the platform (See + ). + + + Level of Partition Performance Parameter Reporting + Supported + + + + + + + + + + Partition Performance Parameter + Level + + + + + Description + + + + + + + + 0 + + + Base Level + + + + + 1 + + + Addition of Processor Virtualization Resource Allocations + to H_GET_PPP and Virtualization Processor idle count to + H_PIC + + + + +
+ + + + + “ibm,preconfigure-usb-kvm” + + + property name the presence of which indicates that + the platform requires the operating system to force configuration of the + USB keyboard/mouse nodes during its configuration phase. + + prop-encoded-array: <NULL> + This property, when present in the root node, indicates that the + platform requires the operating system to force pre-configuration of USB + keyboard/mouse nodes internally during its configuration phase. This + property is presented only by platforms with a KVM switch that desire to + force configuration by one or more target operating systems that do not + fully support dynamic addition of USB keyboard and mouse unless the USB + keyboard and mouse are actually seen during the operating system + configuration phase, but may be present even if the KVM switch is not + present when the device tree is inspected. Forced pre-configuration is + needed since the operating system may not actually see the USB keyboard + and mouse during its configuration phase due to the KVM switch that the + platform uses only shows USB keyboard and mouse when those devices are + actually switched to the appropriate KVM switch port. + + + + + “ibm,enable-ci64-capable” + + + property name to define the platform supports the + “ibm,enable-ci64” method in the Client + Interface. + + prop-encoded-array: None, this is a name only + property. + + + + + “ibm,migratable-partition” + + + property name indicating that the platform supports + the potential migration of this partition. + + prop-encoded-array: NULL + + + + + “ibm,extended-address” [S] + + + property name indicates this platform supports + Peripheral Memory Spaces, Peripheral I/O Spaces, and SCA spaces above 4 + GB. + + prop-encoded-array: <none> + This property must be present. + + + + + “ibm,ignore-hp-po-fails-for-dlpar” + + + property name to define that the OS may ignore + failures of Hot Plug power off and isolate operations during a DLPAR + remove operation. See also Note 2 in + . + + prop-encoded-array: None, this is a name only + property. + + + + + “ibm,managed-address-types” + + + property name that conveys the platform's supported + types of external addresses that are reprogrammable. + + prop-encoded-array: The concatenation, with + encode+, of an arbitrary number of text strings as + described in + , each encoded with + encode-string. + + + Address types supported in + <emphasis role="bold"><literal>“ibm,managed-address-types”</literal></emphasis> + property + + + + + + + + + + Text String + + + + + Description + + + + + + + + ethernet_mac + + + Ethernet MAC address + + + + + ethernet_vlan + + + Ethernet VLAN ID (for default traffic) + + + + + san_wwn + + + Fibre Channel World Wide Name (covers both Port & + Node names) + + + + + sas_wwid + + + SAS IOA's WWID value + + + + +
+ + + + + “ibm,service-indicator-mode” + + + property name indicates in which service indicator + mode the platform is operating. + + prop-encoded-array: an integer encoded as with + encode-int that represents the mode. Defined values + are: + + + + + 0 = Platform is operating in the Guiding Light mode. + + + + 1 = Platform is operating in the Lightpath mode. + + + + + + + + Implementation Notes: + + + + + + In the absence of this property, the determination of how the OS + is to behave is made by the platform presenting or not presenting FRU + Fault indicators to the OS see chapter + . In the case where there are + no FRUs owned by the partition, the OS will not observe any FRU Fault + indicators assigned, even when the platform is operating in the Lightpath + mode. + + + + Presenting this property does not imply any relaxation of the + requirements spe3cified in chapter + . + + + +
+ +
+ Properties of the Children of Root + + + + “ibm,9009-domain” + + + property name that defines the index for a 9009 reset + component indicator, and if it exists, the corresponding 9009 sensor, for + the node in which the property exists. Multiple nodes may have the same + index, indicating that they belong to the same reset domain; including + nodes which are not descendents of the node which contains this property. + Descendents of a node containing this property will be in the same reset + domain. + + prop-encoded-array: An integer encoded as with + encode-phys that represents the index for the + indicator, and if it exists, for the corresponding sensor. + + + + + “ibm,associativity” + + property name to define the associativity domains for this + resource. + prop-encoded-array: One or more associativity lists. Each + associativity list consisting of a number of entries integer (N) encoded + as with + encode-int followed by N integers encoded as with + encode-int each representing an associativity domain + number. + + + + +
+ +
+ Root Node Methods + + This section defines methods associated with the platform via + “/” (the + root node). + + Boot Loader Note: The suggested behavior for boot + loader client programs: + + + + Check the “ibm,rpa-client-config” + property to see if + the platform recognized the “ignore-my-settings” bit in the + boot loader image i.e. YABOOT for LINUX. + + + + If recognized, check for existence of + “ibm,client-architecture-support” + and invoke that method with the + + >ibm,??? compatible (wording???) with the Real Base and Real Size constraints of the + kernel being loaded. + + + + If that method did not exist, invoke + “PROCESS-ELF-HEADER” from /packages/elf-loader with a + simulated ELF-header that the Linux kernel is compatible with. + + + + + ibm,client-architecture-support (ibm,architecture.vec -- + err?) + This method is called via the call-method + Client Interface Service, prior to starting other + partition processors or threads, to communicate to the platform, via the + ibm,architecture.vec structure, the architecture + options that are supported by the client program. Based upon this + knowledge the platform configures itself and the device tree to represent + the most functional programming environment supported by the combination + of the platform, client program and user specified constraints. If + multiple partition processors or threads are active at the time of the + ibm,client-architecture-support method call, or an + error is detected in the format of the + ibm,architecture.vec structure, the + err? boolean shall be + TRUE; else + FALSE. The + ibm,architecture.vec input parameter is the starting + address of a self defining structure in contiguous memory. Some bits + within the + ibm,architecture.vec structure option vectors + represent policies. When set, and an associated condition is detected, + the + ibm,client-architecture-support method does not + return and processing continues as with a boot failure of the client + program. The LoPAR architecture options that are selected by this method + are communicated in the value of the + “ibm,architecture-vec-5” property of the + /chosen node. + To ensure the greatest level of interoperability, the client + program should constrain itself to using the set of instructions and + environment specified for first level interrupt handlers, see Book III of + the + , while not attempting access + to potentially optional SPRs or the MSR prior to invoking the + ibm,client-architecture-support root node + method. + + Architecture and Implementation Notes: + + + + + Most of the + IBM,RPA-Client-Config ELF header functionality is + subsumed by the + ibm,client-architecture-support root method. However, + the + ibm,client-architecture-support root method does not + support the functionality specified through the ns.min-load field of the + IBM,RPA-Client-Config ELF header. Supporting firmware + implementations are prepared to move themselves out of the way when + loading client programs. + + + + When booting a client program, firmware processes an + IBM,RPA-Client-Config ELF header if present; a + subsequent call of the + ibm,client-architecture-support root method with + conflicting values in the + ibm,architecture.vec structure, overrides the + configuration variables set by the ELF header. + + + + + Formal definition of ibm,architecture.vec: + + + ibm,architecture.vec = a + PVR-list: + Number-of-option-vectors: + option-vectors[Number-of-option-vectors + 1] + + PVR-list = + Terminator-list-entry | + Non-terminator-list: Terminator-list-entry + + Non-terminator-list = Non-terminal-list-entry | + Non-terminal-list-entry : Non-terminator-list + + + List-entry = + 4-byte-mask: + 4-byte-PVR-value + + Terminator-list-entry = + List-entry such that ! + 4-byte-mask & + 4-byte-PVR-value != 0x00000000 + + Non-terminator-list-entry = List-entry such that ! + 4-byte-mask & 4-byte-PVR-value == + 0x00000000 + + Number-of-option-vectors = The number of option + vectors is n+1 where n is the numeric value of the byte (byte value of + 0x00 represents one option vector) + + option-vector (option-vectors number 1-255): 1 byte + length of the option vector where the number of bytes in the option + vector (including the first byte of length) is n+2 where n is the numeric + value of the byte (byte value of 0x00 represents a two byte option vector + -- one length byte and one bit-vector byte) followed by 1-256 bytes of + bit-vector. + + option-vector (option-vector number 256): is special + in that it is reserved for expansion. The first byte is again the number + of option vectors in the vector expansion (see definition of + Number-of-option-vectors above). This is followed by + 1-255 + option-vectors (see definition above) and potentially + a 256th + option-vector which is again an expansion option + vector, and so on. + + bit-vector: The structure of a bit vector is vector + specific, in general support for most options are indicated by setting a + specific bit to a 1, see + . + The + PVR-list of the + ibm,architecture.vec structure is processed for the + PVR value of each processor that the client program may be exposed to + until either a + List-entry allows the process to continue, or the + Terminator-list-entry has been processed. If no + List-entry allows the process to continue, then the + ibm,client-architecture-support method terminates + partition operation as with a boot failure. A + List-entry allows the process to continue if either + of the two following conditions hold. + + + + (Processor-PVR-value & + List-entry[4-byte-mask]) == (List-entry[4-byte-PVR-value] & + List-entry[4-byte-mask]) /*The client program explicitly + supports the processor implementation */ + + + + If (the processor requires no client support for errata) + && + (Logical-Processor-PVR-value & List-entry[4-byte-mask]) == + (List-entry[4-byte-PVR-value] & List-entry[4-byte-mask]) /* + Client program specifies support for this level of architecturally + compliant processors */ + + + + + List-entry values of special interest (these are + Terminator-list-entry values): + + + + 0x00000000 0xFFFFFFFF Single entry list that matches any PVR + value + + + + 0xFF000000 0x0FFFFFFF Single entry list that matches all + architecturally compliant processors. + + + + + ibm,architecture.vec option vectors + + + + + + + + + + + Option Array + + + + + Option Vector + + + + + Byte Number + + + + + Bit Number + + + + + Description + + + + + + + + Base + + + 1 + PowerPC Server Processor Architecture Level 6 + + + 1 + + + 0 + + + Ignore 1 + + + + + 1 + + + Cessation Policy 2 + + + + + 2 + + + Reserved for Expansion (0b0) + + + + + 3 + + + + + 4 + + + + + 5 + + + + + 6 + + + + + 7 + + + + + 2 + + + 0 + + + 2.00 + + + + + 1 + + + 2.01 + + + + + 2 + + + 2.02 + + + + + 3 + + + 2.03 + + + + + 4 + + + 2.04 + + + + + 5 + + + 2.05 + + + + + 6 + + + 2.06 + + + + + 7 + + + 2.07 + + + + + 3 + + + 0 + + + 2.08 + + + + + 1-7 + + + Reserved for Expansion (0b0) + + + + + 4-256 + + + Reserved for Expansion + + + + + Base + + + 2 + Open Firmware + + + 1 + + + 0 + + + Ignore 1 + + + + + 1 + + + Reserved + + + + + 2 + + + real-mode + + + + + 3 + + + Reserved for Expansion (0b0) + + + + + 4 + + + + + 5 + + + + + 6 + + + + + 7 + + + + + 2-3 + + + 0-15 + + + Reserved for Expansion (0x0000) + + + + + 4-7 + real-base + + + 0-31 + + + OF real starting address or -1 for platform + default + + + + + 8-11 + real-size + + + 0-31 + + + Maximum OF size or -1 for platform default + + + + + 12-15 + virt-base + + + 0-31 + + + OF starting virtual address or -1 for platform default + (valid for real-mode = 0) + + + + + 16-19 + virt-size + + + 0-31 + + + Maximum OF virtual size or -1 for platform default (valid + for real-mode = 0) + + + + + 20-23 + load-base + + + 0-31 + + + Starting address of the client program load or -1 for + platform default + + + + + 24-27 + min-rma-size + + + 0-31 + + + Minimum size of RMA in MB + + + + (total bytes = N*(2**20)) + + + + + 28-31 + min-load + + + 0-31 + + + Minimum client code to load at load-base or -1 for full + client program at load base + + + + + 32 + min-rma% + + + 0-8 + + + RMA size => M% * Partition_memory_size where M is the + value of this 8 bit field + + + + + + + + 33 + max-pft-size + + + 0-8 + + + The maximum size of the hash page table as 2**n + 17<n<46 + + + + + 34-256 + + + Reserved for Expansion + + +   + + + + + Base + + + 3 + IBM PowerPC Server Processor Options6 + + + 1 + + + 0 + + + Ignore 1 + + + + + 1 + + + Cessation Policy 2 + + + + + 2 + + + Reserved for Expansion (0b0) + + + + + 3 + + + + + 4 + + + + + 5 + + + + + 6 + + + + + 7 + + + + + 2 + + + 0 + + + Floating Point + + + + + 1 + + + VMX + + + + + 2 + + + Decimal Floating Point + + + + + 3 + + + Decimal Floating Point Facility (The value of the ibm,dfp + property indicates the architecture level of the + facility.) + + + + + 4 + + + Reserved for Expansion (0b0) + + + + + 5 + + + + + 6 + + + + + 7 + + + + + 3-256 + + + Reserved for Expansion + + + + + Base + + + 4 + LoPAR Implementation + + + 1 + + + 0 + + +   + + + + + 1 + + + Cessation Policy 2 + + + + + 2 + + + Reserved for Expansion (0b0) + + + + + 3 + + + + + 4 + + + + + 5 + + + + + 6 + + + + + 7 + + + + + 2 + + + 0-7 + + + Minimum VP entitled capacity percentage * 100 (if absent + assume 10%) + + + + + 2-256 + + + Reserved for Expansion + + + + + Base + + + 5 + LoPAR or OF Options 5 + + + 1 + + + 0 + + + Ignore 1 + + + + + 1 + + + Cessation Policy 2 + + + + + 2 + + + Reserved for Expansion (0b0) +   + + + + + 3 + + + + + 4 + + + + + 5 + + + + + 6 + + + + + 7 + + + + + 2 + + + 0 + + + Logical Partitioning: If set the client program supports + logical partitioning and associated hcall()s; else the client + program shall be run with the hypervisor bit on.7 + + + + + 1 + + + Shared Processor Logical Partitioning: If set the client + program supports the Shared Processor LPAR Option and may be + run with that option enabled; else the Shared Processor LPAR + Option shall be disabled for this partition. + + + + + 2 + + + ibm,dynamic-reconfiguration-memory: If set the client + program supports the + “ibm,dynamic-reconfiguration-memory” + property and it may be presented in the device tree; else, the partition + memory shall be represented with individual + memory nodes. + + + + + 3 + + + Large Pages: If this bit is set, the client supports + pages larger than 4 KB; else, the platform shall represent all + of memory as mapped via 4 K pages. + + + + + 4 + + + Alpha Partition 4 + + + + + 5 + + + Tolerate long delays in H_MIGRATE_DMA + + + + + 6 + + + Client supports donating dedicated processor + cycles + + + + + 7 + + + PCI Express/MSI Support: If set, the client supports PCI + Express implementations utilizing Message Signaled Interrupts + (MSIs). + + + + + 3 + + + 0 + + + On input to ibm,client-architecture-support a non-zero + value indicates that the client supports the I/O Super Page + Option (Support of >4K I/O pages) (Includes extensions to + H_MIGRATE_DMA for >4K I/O pages and >256 xlates). + . +   + In the + ibm,architecture-vec-5 property of the + /chosen node, a non-zero value indicates + that the platform supports the I/O Super Page Option (Support + of >4K I/O pages). + + + + + 1-4 + + + On input to ibm,client-architecture-support this field + shall be zero. +   + In the + ibm,architecture-vec-5 property of the + /chosen node, this field represents the + implementation dependent number of xlates entries supported per + migration operation as: 256 * 2**N. + . + + + + + 5-7 + + + On input to ibm,client-architecture-support this field + shall be zero. +   + In the + ibm,architecture-vec-5 property of the + /chosen node, this field represents the + implementation dependent number of simultaneous migration + options supported as: 2**N. + . + + + + + Base +   + + + 5 + LoPAR or OF Options 5 +   + + + 4 + + + Cooperative Memory Over-commitment Option Control + + + + + 0 + + + The value of 1 enables the Cooperative Memory + Over-commitment Option + + + + + 1 + + + The value of 1 enables the Extended Cooperative Memory + Over-commit + Option + + + + + 2-7 + + + Reserved for Expansion + + + + + 5 + + + Associativity Information Option Control + + + + + 0 + + + = the “Form value” of the + “ibm,associativity” and + “ibm,associativity-reference-points” + properties. See for further details. + + + + + 1 + + + Platform Resource Reassignment Notification (Affinity + Change) + + + + + 2-7 + + + Reserved for Expansion + + + + + 6 + + + Binary Option Controls + + + + + 0 + + + Enable MTT Option + See + . + + + + + 1 + + + Reserved + + + + + 2 + + + Enable Active Memory Compression + + + + + 3 + + + Enable Universlly Unique IDentifier Option (UUID) + + + + + 4 + + + Reserved for Expansion + + + + + 5-7 + + + Reserved for Expansion + + + + + 7 + + +   + + + Reserved for Expansion + + + + + 8 + + +   + + + Reserved for Expansion + + + + + 9-12 + + + Max Processors Supported + (For legacy support, if this byte is not present the + partition is limited to a maximum of 64 processors) + + + + + 0-31 + + + 32 bit unsigned integer maximum number of OF device tree + nodes of type “cpu” that may be presented to this + partition. + + + + + 13-14 + + + 0-7 & 0-7 + + + Highest Base LoPAR Level Supported as the binary + contents of 13.14 + (i.e. level 4.15 would be encoded as 0x040F) + + + + + 15-16 + + +   + + + Reserved for Expansion + + + + + Base +   + + + 5 + LoPAR or OF Options 5 +   + + + 17-20 + + + Platform Facilities Enable – Value of 0b1 indicates + facility is enabled + + + + +   + + +   + + + 0 + + + Random Number Generator + + + + +   + + +   + + + 1 + + + Compression Engine + + + + +   + + +   + + + 2 + + + Encryption Engine + + + + +   + + +   + + + 3-31 + + + Reserved for Expansion -- Value = 0b0 + + + + +   + + +   + + + 21 + + + 0-7 + + + Sub-Processor Representation Level -- + Defined Values: +   + 0: Sub-Processors not supported + 1: 1,2,or 4 Sub-Processors supported + 2-255 Reserved + + + + +   + + +   + + + 22-256 + + +   + + + Reserved for Expansion + + + + + Base + + + 6 + Hints + + + 1 + + + 0 + + + Reserved for Expansion (0b0) + + + + + 1 + + + + + 2 + + + + + 3 + + + + + 4 + + + + + 5 + + + + + 6 + + + + + 7 + + + + + 2 + + + 0 + + + Secondary Page Table Entry Group: If set, the client does + not use secondary page table entry groups; else the client may + use secondary page table entry groups. + + + + + 1 + + + Reserved + + + + + 2 + + + + + 3 + + + + + 4 + + + + + 5 + + + + + 6 + + + + + 7 + + + + + 3 + + + 0-7 + + + OS Name: Represents the name of the client OS. Defined + values include: + 0x0: Reserved + 0x1: AIX + 0x2: Linux + 0x3-0xFF: Reserved for Expansion + + + + + 4-256 + + + Reserved for Expansion + + + + + 7 + OS Identification + + + 1-256 + + + An ASCII character formatted null terminated string that + describes the client operating system. The string shall be + human readable and may be displayed on the console. + + + + + 8-255 + + + Reserved for Expansion + + + + + 256 + + + Reserved for Expansion to the first Extension Option + Array + + + + + Extensions 1-N + + + Reserved for Expansion + + + + +
+ Notes: + + + + The Ignore Policy bit indicates that the client program assumes + all responsibility for the options represented by the option vector. The + firmware is to configure the platform at the highest level consistent + with its configuration variables and ignore the rest of the specific + option vector. An option vector with the Ignore Policy bit set need be no + longer than two bytes (size=0, data = 0b1ddd dddd where d = don’t + care). + + + + The Cessation Policy Bit determines if the partition continues + to run if the platform must operate with an option enabled that is not + explicitly supported by the client program as represented by the option + vector setting. If the Cessation Policy Bit is 1, then processing halts + as with a boot failure. If the Cessation Policy Bit is 0 then client + program processing continues if the unsupported option is initialized to + a benign state and stays in that state unless an aware program activates + the option, and the option does not appear in the device tree. If an + unsupported option cannot be initialized to a benign state, then + processing halts with a boot failure. Following are the detailed + definitions of benign state for selected bit vectors. + + + + For option vector numbers 1 “PowerPC Server Processor + Architecture Level” and 3 “IBM PowerPC Server Processor + Extensions” the benign state is defined as unable to generate + exceptions, mask errors, or present covert channel exposures. + + + + For option vector number 5 “LoPAR Options” Byte 2 + bit 5 “Alpha Partition” The Cessation Policy bit is not + applicable. + + + + For option vector number 2 “Open Firmware” the + Cessation Policy Bit is not defined, the platform either accommodates the + values defined in the option vector or proceeds as with boot + failure. + + + + + + The Initial size + of the RMA is set to the greater of the values indicated by bytes 24-27 + or 32 of option vector number 2 “Open Firmware” or minimum + RMA size supported by the platform and capped by the maximum memory + defined for the partition and the maximum size of the RMA supported by + the platform. The respective selected values are reported in the length + of the first + memory property. + + + + The Alpha flag only applies to the first partition of a non HMC + managed system and activates overrides to the partition's I/O resource + allocation as defined in the partition definition. + + + + If the system is HMC managed, the flag is ignored and the client + program gets the resources assigned by its partition definition (no + overrides are activated). + + + + If the partition is not the first partition, the flag is ignored + and the client program gets the resources assigned by the partition + definition (no overrides are activated). + + + + If the Alpha flag applies, and is set, then the partition gets a + VMC virtual I/O device in its device tree regardless of its partition + definition (Override to include VMC is activated). + + + + If the Alpha flag applies, and is not set, then the partition + does not get a VMC virtual I/O device in its device tree regardless of + its partition definition (Override to remove VMC is activated) and it + gets all the physical I/O resources in its device tree regardless of its + partition definition (Override to include all physical I/O is activated). + Note this condition requires that any other platform partitions be + terminated. + + + + + + Given that the Ignore policy bit is off and the partition + continues to run, the options and values presented in by this option + vector and supported/chosen by the platform firmware are reported in the + “ibm,architecture-vec-5” property of the + /chosen node. + + + + Option vector number 1 “PowerPC Server Processor + Architecture Level” and the property that reports the chosen value + (i.e., + “cpu-version”) represent the operational + base architectural level of the processors -- that is without regard to + enabled processor architectural options. Option vector number 3 + “IBM PowerPC Server Processor Extensions” and option specific + properties that report the chosen values represent the active processor + architectural options. Some processor implementations may not support all + combinations of these two option vectors. The firmware shall activate the + highest level of processor support, consistent with partition attributes, + that does not exceed the most restrictive of the two option vectors. Note + the Cessation Policy bit may allow operation where the lowest level of + processor support still exceeds the most restrictive case. + + + + If a client program does not support logical partitioning no + other client programs may be running simultaneously on the platform. The + platform may impose further restrictions beyond the scope of LoPAR. If + the platform honors the client program restriction of not supporting + logical partitioning, upon return the logical real address equals the + platform real address. If the platform can not honor the restriction, the + processing terminates as with a boot failure. The cessation policy option + vector bit has no effect upon logical partitioning option vector + bit. + + + +
+ +
+ ROM Node(s) + + The ROM Node(s), when present to represent optional platform read + only memory containing directly executable platform firmware, shall be a + child or children of the root node. + +
+ ROM Node Properties + + Each ROM Node shall have the following properties: + + + + “name” [S] + + Standard + property name that denotes a ROM Node. + + prop-encoded-array: A string, encoded as with + encode-string. + The value of this property shall be + “rom”. + + + + + “reg” [S] + + Standard + property name to define a unit-address for the + node. + + prop-encoded-array: One ( + phys-addr, size) pair. + The + phys-addr of this property shall be the starting + physical address of this ROM and the + size value shall be 0. The + size =0 prevents a conflict with the + “reg” of this node’s + children. + + + + + “#address-cells” [S] + + Standard + property name to define the address space + representation of child nodes. + + prop-encoded-array: an integer, encoded as with + encode-int. Its value shall be identical to that of + this node’s parent’s + “#address-cells” value. + + + + + “ranges” [S] + + Standard + property name to define the address range that is + decoded by this + /rom node. + + prop-encoded-array: One ( + child-phys, + parent-phys, + size) triple, where + child-phys equals + parent-phys and the number of cells of each + corresponds to the parent’s + “#address-cells” value. + + + + + “available” [S] + + Standard + property name to define available ROM + resources. + + prop-encoded-array: Arbitrary number of + phys-addr, size pairs. + Phys- + addr is a + phys.hi...phys.lo list of integers, each integer + encoded as with + encode-int. + Size is one or more integers, each encoded as with + encode-int. + The value of this property defines resources, managed by this + package, that are currently available for use by a client program. + + + + + “write-characteristic” [S] + + Standard + property name defines the ROM Technology. + + prop-encoded-array: a string, encoded as with + encode-string, where the value could equal + “flash”, + “eeprom”, + “rom” or + “nvram”. + + + + + “cacheable” [S] + + OF standard property indicating that the ROM is cacheable. + + prop-encoded-array: <none>. + The presence of this property indicates that the ROM is + cacheable. + + + + +
+ +
+ ROM Node Methods + + If one or more ROM nodes are present, they shall each implement the + following standard methods per + , Section 3.6.1. The + “reg” property is used to determine which + ROM the standard methods apply to for multiple ROM’s. + The following methods must be defined by + /rom node. + + + + open (-- true) [M] + + Standard method to prepare the ROM Node for subsequent use. + + + + + close (--) [M] + + Standard method to close the previously opened ROM Node. + + + + + decode-unit + (addr len -- phys.lo...phys.hi) [M] + + Standard method to convert text unit-string to physical address. + + + + + encode-unit + (phys.lo...phys.hi -- unit-str unit-len) [M] + + Standard method to convert physical address to text unit-string. + + + + + probe (--) [M] + + OF method used at boot time to probe all ROM’s. + The + probe method for ROM Nodes shall probe for FCode + images within the address space defined by its + “reg” property as defined herein. For + each page within its address space, look for a valid FCode image. A valid + FCode image is defined to start with an FCode-header (see section 5.2.2.5 + in + ) where the first byte is + start1, the format byte is 0x08, the length field + indicates that the FCode program is contained within the address space of + the + /rom node, and where the checksum is correct. (This + probing must take into account the possibility that the ROM image is in + the opposite endian-ness from which OF is currently running.) + If such an FCode image is found, a new child node shall be created + by executing + new-device and + set-args, the FCode image copied to memory (taking + into account the endian-ness) and the copy evaluated with + byte-load. (The FCode program can use + my-unit to create its + “reg” property.). The arguments used by + set-args are defined to be 0,0,unit-str, unit-len + where unit-str is a text string representation of the physical address + location for the FCode Image and unit-len is the length of the FCode + Image. + + + + +
+ +
+ +
+ ROM Child Node(s) + This section describes the properties and methods for a ROM Child + Node. + +
+ ROM Child Node Properties + + The following properties must be created by + /rom child nodes. + + + + “name” [S] + + Standard + property name that denotes a ROM child node. + + prop-encoded-array: A string, encoded as with + encode-string. + Some physical ROM implementations may not fully decode their entire + address range. This could lead to multiple images of the ROM to appear at + different addresses, due to the “aliasing” of the ROM image. + To prevent multiple device nodes from appearing in the device tree, the + FCode for such ROMs should look for an already existing peer node that + represents their image. This could be done, for example, by checking that + any of the peer of the child of its parent node has a + “name” property value that is the same as + this node’s FCode would create. + If such a node is found, the FCode should “abort” the + evaluation of its FCode (e.g., by executing an + end0) before creating its + “name” property. OF shall remove a node + when the FCode evaluation for the node does not result in a + “name” property being defined. + + + + + “reg” [S] + + Standard + property name that defines the child node address + range for a ROM image(s). + + prop-encoded-array: List of ( + phys-addr, size) specifications. + + Phys-addr is encoded as with + encode-phys, and + size is encoded as with + encode-int. The + phys-addr is a base address of the ROM image and + size is the length of the ROM image. + + + + +
+ +
+ ROM Child Node Methods + + The following methods must be defined by + /rom child nodes. + + + + open (-- true) [M] + + Standard method to prepare this device for subsequent use. + The + open method must be prepared to parse + my-args for the case(s) when the node is being opened + in order to access “files”; e.g., when the bootinfo.txt file + is being accessed during the + multiboot menu. + + + + + close (--) [M] + + Standard method to close the previously opened device. + + + + + load (addr -- len) [M] + + Standard method to load an image. The image must be one that is + recognized by the OF + init-program method. It is strongly recommended that + the ELF format be used, since it has the mechanism to specify + configuration variable requirements of an OS. + + + + +
+ +
+ +
+ +
+ Run Time Abstraction Services (RTAS) Node + + This system node is a child of + “/” (root). This section defines + properties and methods for the RTAS node. The RTAS Node shall not have + “reg” or + “ranges” properties. + +
+ RTAS Node Properties + + This section describes the + rtas node properties. + + + + “name” [S] + + Standard + property name that denotes the RTAS node. + + prop-encoded-array: A string, encoded as with + encode-string. + The value of this property shall be + “rtas”. + + + + + “rtas-event-scan-rate” [S] + + + property name that is the rate at which an OS should + read indicator/sensor/error data + + prop-encoded-array: An integer, encoded as with + encode-int + The value of this property shall be a number indicating the desired + rate for reading sensors and/or error information in calls per minute. + This number is platform dependent. + + + + + “rtas-indicators” [S] + + + property name that indicates indicators are + implemented. + + prop-encoded-array: An array of paired integers ( + token maxindex), each encoded as with + encode-int. + The values for this property is a list of integers that are the + token values ( + token) for the defined indicators and the number of + indicators ( + maxindex) for that token which are implemented (see + ) on the platform. + + Note: The indicator indices for a given token are + numbered 0... maxindex-1. + + + + + “rtas-sensors” [S] + + + property name that indicates sensors are + implemented. + + prop-encoded-array: An array of paired integers ( + token maxindex), each encoded as with + encode-int. + The values for this property is a list of integers that are the + token values ( + token) for the defined sensors and the number of + sensors ( + maxindex) for that token which are implemented (see + ) on the platform. + + Note: The sensor indices for a given token are + numbered 0 ... maxindex-1. + + + + + “rtas-version” [S] + + + property name describes version information for the + RTAS implementation. + + prop-encoded-array: An integer, encoded as with + encode-int. + The value of this property shall denote the version the RTAS + implementation. For this version, the integer shall be as defined in this + architecture. + + + + + “rtas-size” [S] + + + property name is the size of the RTAS memory + image. + + prop-encoded-array: An integer, encoded as with + encode-int. + The value of this property shall be the amount of contiguous real + system memory required by RTAS, in bytes. + + + + + “rtas-display-device” [S] + + + property name identifies RTAS Display Device + + prop-encoded-array: An integer, encoded as with + encode-int. + The value of this property shall be the + phandle of the device node used by the RTAS + display-character function. + + + + + “rtas-error-log-max” [S] + + + property name identifies maximum size of an extended + error log entry. + + prop-encoded-array: An integer, encoded as with + encode-int. + The value of this property shall be the maximum size of an extended + error log entry, in bytes. + + + + + “power-on-max-latency” [S] + + + property name specifies a future power on time + capability. + + prop-encoded-array: An integer, encoded as with + encode-int. + The value of this property specifies the capability of the hardware + to control the delay of system power on in days. If the property is + present, the value shall indicate the maximum delay or latency in days. + If the property is not present, the maximum delay or latency is 28 + days. + + + + + “ibm,preserved-storage” + + + property name specifies that the client program was + loaded with one or more LMBs preserved from a previous client + program. + + prop-encoded-array: None, this is a name only + property. + The client program may wish to save the contents of the preserved + LMBs and deregister the LMBs for preservation. + + + + + “ibm,scan-log-directory” + + property name specifies that the platform supports + the scan-log directory option. + + prop-encoded-array: None, this is a name only + property. + + + + + “ibm,indicator-<token>” + + property name to provide a FRU location code for + identifying each indicator. + + prop-encoded-array: an array of + maxindex + 1 strings, encoded as with + encode-string. + + + + + “ibm,sensor-<token>” + + property name to provide a FRU location code for + identifying each physical sensor. + + prop-encoded-array: an array of + maxindex + 1 strings, encoded as with + encode-string. + + + + + “ibm,display-line-length” + + property name to provide the length of a display line + in number of characters. + + prop-encoded-array: an integer, encoded as with + encode-int. + + + + + “ibm,display-number-of-lines” + + property name to provide the number of lines in the + display. + + prop-encoded-array: an integer, encoded as with + encode-int. + + + + + “ibm,display-truncation-length” + + property name, when provided, specifies the length to + which each line to be display is truncated, based on which line of the + physical display on which the line is displayed. When the truncation + length is greater than the length specified in the + “ibm,display-line-length” property, then + the platform provides a platform-dependent method of displaying the line + to the user. + + prop-encoded-array: An array of integers, each + encoded as with encode-int. The number of integers corresponds to the + number of lines, as defined by the + “ibm,display-number-lines” property. The + first integer refers to the truncation length for the first physical line + of the display, the second to the second physical line, and so on. + + + + + “ibm,form-feed” + + property name to provide an indication of the + form-feed capability. + + prop-encoded-array: a character, NULL (0x00) if + form-feed is not supported and np (0x0C) if form-feed is supported, + encoded as with + encode-int. + + + + + “ibm,environmental-sensors” + + property name describes the environmental sensors + which are available to an application. + + prop-encoded-array: An array of paired integers + (token maxindex), each encoded as with + encode-int. + + + + + “ibm,flash-block-version” + + + property name in the + /rtas node indicates the block list format to be + used. + + prop-encoded-array: integer encoded as with + encode-int. Value is 0x01 for the discontiguous + block list. (If a new version of the block list is ever required, other + values could be defined.) + + + + + “ibm,errinjct-tokens” [S] + + property name defines the error inject functions implemented on + this platform. + prop-encoded-array: List of (errinjct-token-name, + errinjct-token-value) specifications. + errinjct-token-name: A string, encoded as with + encode-string. + errinjct-token-value: is encoded as with + encode-int. + + + + + “ibm,lrdr-capacity” + + property name in the + /rtas node identifies the dynamic reconfiguration + capabilities of the partition + + prop-encoded-array: A triple consisting of phys, + size, and one integer encoded as with + encode-int + The phys (of size #address-cells) communicates the maximum address + in bytes and therefore, the most memory that can be allocated to this + partition. + The size (of size #size-cells) communicates the increment (quantum + of logical memory dynamic reconfiguration). + The first integer communicates the maximum number of processors + (implied quantum of 1). + + Note: Some implementations depend upon the presence + and value of a second integer. Future extensions to this property should + not define a second integer for new purposes. + + + + + “ibm,hypertas-functions” + + property name of the + /rtas node, defines the platform’s implemented + hypervisor RTAS function sets. + prop-encoded-array: List of Hypervisor-RTAS-function-set + specifications. + Each Hypervisor-RTAS-function-set specification is a byte string + encoded as with + encode-string. + + + + + “ibm,dma-delay-time” + + property name to define the time delay need to ensure outstanding + DMA operations targeting migrated pages have completed. + prop-encoded-array: A one cell integer encoded as with + encode-int that represents the number of + micro-seconds that the OS should wait prior to reusing migrated DMA read + target pages. + + + + + “ibm,associativity-reference-points” [S] + + property name to define the associativity reference points for the + “ibm,associativity” + properties of this platform. + prop-encoded-array: A list of one or more integers cell(s) encoded + as with + encode-int. + + + + + “ibm,max-associativity-domains” + + property name to define the maximum number associativity domains + for this platform. + prop-encoded-array: An associativity list such that all values are + the maximum that the platform supports in that location. The + associativity list consisting of a number of entries integer (N) encoded + as with + encode-int followed by N integers encoded as with + encode-int each representing maximum number + associativity domains the platform supports at that level. + + + + + “ibm,request-partition-shutdown” + + + property name to specify that the partition was + rebooted in the forced fire hose dump mode. + + prop-encoded-array: An integer encoded as with + encode-int that represents the platform’s + partition shutdown configuration variable. The defined states are: + 0 = The platform boots with no request to save appropriate data nor + shutdown the partition. + 1 = The platform boots with a conditional request to save + appropriate data and shutdown the partition. The client program should + check for an EPOW sensor state of 3 and if present, it should save + appropriate data and shutdown the partition. If the EPOW sensor state of + 3 is not present, then the partition should initiate a reboot since the + device tree will be incomplete. + 2 = The platform boots with a mandatory request to the client + program to save appropriate data and shutdown the partition. + + + + + “ibm,integrated-stop-self” + + + property name indicating that prior to placing a + processor in the stopped state, the platform flushes and disables any + caches/memory exclusively used by the issuing processor. + + prop-encoded-array: NULL + + + + + “ibm,rks-hcalls” + + + property name: indicating the hcalls that are + implemented with a reduced kill set. Absence of this property indicates + that only hcalls that are specified as always having a reduced kill set + provide that semantic. + + prop-encoded-array: A one to N byte bit vector, bit + positions representing hcall()s (see + ) that present a reduced kill + set per their architectural specification. + + + <emphasis role="bold"><literal>“ibm,rks-hcalls”</literal></emphasis> bit vector to hcall map + + + + + + + + + + + Byte Number + + + + + Bit Number + + + + + hcall + + + + + + + + 0 + + + 0 + + + 0b11 for H_CONFER & H_PROD + + + + + 1 + + + + + 2 + + + Set to 1 if H_PURR is implemented with a reduced volatile + kill set of r3 & r4; else set to 0. + + + + + 3 + + + Reserved for future expansion (0b0) + + + + + 4 + + + + + 5 + + + + + 6 + + + + + 7 + + + + + 1-N + + + Reserved for future expansion + + + + +
+ + + + + “ibm,reset-capabilities” + + + property name indicates what capabilities the + platform supports relative to the ibm,set-slot-reset RTAS call, when that + RTAS call is implemented. + + prop-encoded-array: An integer encoded as with + encode-int that represents the functions supported in the + ibm,set-slot-reset RTAS call + 0 = Platform supports Functions 0 and 1 supported. + 1 = Platform supports Functions 0, 1, and 3. + Note: The absence of this property implies the platform supports + Functions 0 and 1 for the + ibm,set-slot-reset RTAS call, when that RTAS call is + implemented. + + + + + “ibm,configure-kernel-dump-sizes” + + + property name specifies that the Platform Assisted + Kernel Dump option is supported for sections described by this + property. + + prop-encoded-array: For each dump section type + supported, a 32 bit cell which defines the ID of a supported section + followed by two 32-bit cells which gives the size of the section in bytes + (not including any disk headers.) + + + + + “ibm,configure-kernel-dump-version” + + + property name specifies that the Platform Assisted + Kernel Dump option is supported for versions described by this + property. + + prop-encoded-array: Contains a 16-bit cell describing + the minimum kernel dump version supported by the firmware followed by a + 16-bit cell describing the maximum kernel dump version supported by the + firmware. + + + + + “ibm,kernel-dump” + + + property name specifies the presence of a registered + kernel dump in the Platform Assisted Kernel Dump option. + + prop-encoded-array: Contains the description of the + registered kernel dump in the format described in + . + + + + + “ibm,read-slot-reset-state-functions” + + + property name specifies the implementation of certain + input or output fields in the + ibm,read-slot-reset-state2 RTAS call. If this + property does not exist, then the + ibm,read-slot-reset-state2 RTAS call implements only + the first 3 inputs and the first 4 outputs ( + Number Inputs is required to be 3 and the + Number Outputs is required to be 4), as defined in + . + + prop-encoded-array: Contains a 32 bit cell, with the + bits defined as follows: + Bits 0-29: Reserved (value of 0). + Bit 30: When a value of 1, the + ibm,read-slot-reset-state2 RTAS call checks the + Number Outputs and the implements the 5th output ( + Number Outputs of 5), as defined by + . + Bit 31: When a value of 1, the + ibm,read-slot-reset-state2 RTAS call implements the + first 3 inputs and the first 4 outputs ( + Number Inputs of 3 and the + Number Outputs of 4), as defined in + . This bit is always required + to be a value of 1 when this property is implemented. + + + + + “ibm,change-msix-capable” + + + property name indicating the platform supports the + ibm,change-msi RTAS call with + Number of Outputs equal to 4 and + Functions 3 and 4. + + prop-encoded-array: <none> + + + + +
+ +
+ <literal>/RTAS</literal> node DR Sensors and Indicators + + The following sensors and indicators are defined for the /RTAS node + for the DR option. + + + + “9003” + + sensor token, the existence of this token number + denotes that the platform supports the 9003 “DR entity sense” + sensor. + + + + + “9001” + + indicator token, the existence of this token number + denotes that the platform supports the 9001 “isolation state” + indicator. + + + + + “9002” + + indicator token, the existence of this token number + denotes that the platform supports the 9002 “dr-indicator” + indicator used to guide operators in the physical add or removal of + hardware. + + + + + “9003” + + indicator token, the existence of this token number + denotes that the platform supports the 9003 + “allocation-state” indicator. + + + + + “ibm,extended-os-term” + + property-name indicating that the platform supports + extended + ibm,os-term behavior as described in + . + prop-encoded-array: encode-null + + + + +
+ +
+ RTAS Function Property Names + + This section defines the property names associated with the various + RTAS functions defined by + . + should be used as the reference + for RTAS Functions currently implemented. Each RTAS function that a + platform implements shall + be represented by its own function property, + who’s value is the + token used to invoke the function on an RTAS + call. + The formal property definition for each such property is of the + form: + + property name specifies the name of the RTAS function + -- such as: + + + + “nvram-fetch” [S] + + prop-encoded-array: The value, + token, is an integer encoded as with + encode-int. + If an RTAS function is implemented, there is a property name which + corresponds to its function name. The value of this property is a + token. This + token, when passed to RTAS via its + rtas-call interface (see below), invokes the named + RTAS function. If a RTAS function is not implemented, there will not be a + property corresponding to that function name. See the + for more information about RTAS + functions. + + + + + “ibm,termno” + + property name of the + /rtas node defines the virtual terminal numbers + available for use by this partition. + prop-encoded-array: A pair of integers encoded as with + encode-int, the first being the value + of the lowest termno in a contiguous range of supported values, the second being the + number of termno values supported. + Note: The number of supported termno values is + implementation dependent -- the minimum number is one. + + + + + “ibm,hypertas_functions” + + property name of the /RTAS node, defines the + platform’s implemented hypervisor RTAS function sets. + + prop-encoded-array: List of + Hypervisor-RTAS-function-set specifications. + Each + Hypervisor-RTAS-function-set specification is a byte + string encoded as with + encode-string. + + + + +
+ +
+ RTAS Node Methods + + The + instantiate-rtas or + instantiate-rtas-64 method is invoked by the OS to + instantiate the RTAS functionality. This is accomplished via the + call-method + Client Interface Service. If the platform supports + the + ibm,client-architecture-support root node method, and + that method has not been called prior to the call of the + instantiate-rtas or + instantiate-rtas-64 methods, then the platform shall + operate at the least functional level supported by the platform. + + Note: Platforms should provide a manual override + capability to allow most functional level allowed by the partition + configuration in the event that a client program does not call the + ibm,client-architecture-support root node method + prior to the instantiation of RTAS. + + + + instantiate-rtas (rtas-base-address -- rtas-call) [M] + + Invoking the + instantiate-rtas method binds the RTAS environment to + a given location in System Memory and initializes the RTAS environment. + The in parameter, + rtas-base-address, is the physical address to which + the RTAS environment is to be bound. This call indicates that RTAS is + instantiated in a 32-bit mode. The amount of contiguous real memory that + should be allocated for the RTAS environment is given by the value of the + “rtas-size” property. + Upon completion of the + instantiate-rtas method, an entry point address, + rtas-call, is returned. The value of + rtas-call specifies the physical address of the entry + point into RTAS for future RTAS function calls. + + + + + instantiate-rtas-64 (rtas-base-address -- rtas-call) [M] + + Invoking the optional + instantiate-rtas-64 method binds the RTAS environment + to a given location in System Memory and initializes the RTAS + environment. The in parameter, + rtas-base-address, is the physical address to which + the RTAS environment is to be bound. This call indicates that RTAS is + instantiated in a 64-bit mode. The amount of contiguous real memory that + should be allocated for the RTAS environment is given by the value of the + “rtas-size” property. + Upon completion of the + instantiate-rtas-64 method, an entry point address, + rtas-call, is returned. The value of + rtas-call specifies the physical address of the entry + point into RTAS for future RTAS function calls. + + + + +
+ +
+ +
+ Properties of the Node of type cpu + When the platform implements the LPAR option the following + properties are required of the /cpus node + + + + ibm,pft-size + + property name of the children of type + “cpu” of the + /cpus node, defines the size of the processor’s + page frame table. + prop-encoded-array: A pair of integers encoded as + with + encode-int, the first being the NUMA CEC Cookie (up + to a maximum of (2 + 16)-1) the second being the base 2 log of the size + of the page frame table in bytes. + + Notes: + + + + + On single CEC platforms, the NUMA CEC Cookie value is + zero. + + + + Due to constraints caused by initial memory allocations, and + other running partitions, the firmware may not be able to allocate a + node’s PFT for the full size requested in the PFT_size + configuration variable. The + “ibm,pft-size” property of course + reflects the actual size allocated. + + + + The partitions running on multiple NUMA nodes would have + multiple PFTs which did not look alike due to the difference in mapping + local and remote page frames.) + + + + + + + + + To support dynamic addition and removal of processors, the /cpus + node contains the properties: + ibm,drc-types (cpu), + ibm,drc-indexes ibm,drc-names and + ibm,drc-power-domains (-1's). These properties have + entries for the maximum number of dynamically reconfigurable processors + that the platform supports for the specific OS image. + + + + “ibm,ppc-interrupt-server#s” [S] + + property name: Defines the single processor server + numbers associated with this processor. Placing the numerical equivalent + of one of these quantities into the server# field of an XIVR directs + associated interrupts to this processor. The first server number is + associated with the “primary processor thread” any subsequent + numbers are associated with the secondary. etc. hardware threads that the + processor may implement. + prop-encoded-array: A list of one or more integers + in the range of 0 to + 2“ibm,interrupt-server#-size” + encoded as with + encode-int. + Note: In order to achieve optimal performance, + processor server numbers should be activated in the order that they are + presented in the + “ibm,ppc-interrupt-server#s” property and + deactivated in the reverse order. + + + + + “ibm,ppc-interrupt-gserver#s” [S] + + property name: Defines the multiple processor global + server numbers to which this processor belongs. Placing the numerical + equivalent of one of these quantities into the server# field of an XIVR + directs associated interrupts to one of the processors in that + group. + prop-encoded-array: A list of ( + server#, gserver#s) specification pairs. the first + integer specifies a single processor + server# as presented in the node’s + “ibm,ppc-interrupt-server#s” property, + followed by an integer with a value less than or equal to 2 + “ibm,interrupt-server#-size” + encoded as with + encode-int that specifies the global server queue + that also may present interrupts to the interrupt management area + associated with the + server#. + + + + + “ibm,sub-processors” + + property name: the sub-processor configuration that + is running on this processor. In the absence of this property, this + processor may not be divided into sub-processors. + prop-encoded-array: a series of three or more + integers each encoded as with encode-int. The value of the first integer + indicates how many integers follow (the value 2 indicates that two + integers follow). The second integer indicates the number of + sub-processors that are running on this processor. If the processor is + not divided into sub-processors the value of the second integer shall be + 1, two sub-processors shall be represented by the value 2, four + sub-processors shall be represented by the value 4 and so on. The third + integer indicates the maximum number of sub-processors that could be + configured to run on this processor. + Client programs shall ignore subsequent integers beyond those + defined at the time they were written. + + + + +
+ +
+ Extensions for LoPAR I/O Sub-Systems + + LoPAR I/O sub-system events may be signaled in a variety of ways + depending upon platform capabilities. In order of increasing + functionality: + + + + Events are universally fatal, and are signaled via + checkstop. + + + + After being enabled, the effected section enters freeze state + signalling this state with a return of all 1’s to any MMIO load + instruction (If not enabled functionality of the specific section reverts + to #1. Presence of + ibm,set-eeh-option RTAS call denotes platforms that + support this level of functionality.) + + + + An extension to #2 above wherein, after being enabled for a + specific section of the I/O sub-system, additional event conditions may + be reported and events are signaled using an external interrupt. The + platform’s capability to support this level of functionality is + reported by the inclusion of the + “ibm,i/o-events-capable” property (see + definition below) in nodes where enabling control may be + exercised. + + + + + + “ibm,i/o-events-capable” + + property name indicating that I/O sub-system events + detected by the hardware represented by this node in the device tree may + be singled with an I/O event interrupt if enabled. + prop-encoded-array: 0 to N interrupt specifiers (per + the definition of interrupt specifiers for the node’s interrupt + parent). + When no interrupt specifiers are present, then the interrupt, if + enabled, is signaled via the interrupt specifier given in the + I/O-events child node of the + /events node. + To perform certain management functions, it is necessary to quiesce + segments of the platform’s I/O infrastructure, such quiescence + domains are not representable by a strict tree structure. The + “ibm,io-quiesce-domains” property relates + the membership of the various elements of a platform’s I/O + sub-system to such quiescence domains. + + + + + “ibm,io-quiesce-domains” + + property name indicating the I/O quiesce domains of + which this device, and all devices under this device (if any), is a + member. + prop-encoded-array: List of one or more + domain-id’s to which this device belongs, and to which all devices + under this device (if any) belongs. Domain-id's are encoded as with + encode-int. + + + + + Virtual I/O that does not take up physical address locations is + represented in a device sub tree for which the + “#size-cells” and + “#address-cells” properties are zero and + one, respectively. However, the ibm dma-window properties, such as + “ibm,dma-window” and + “ibm,my-dma-window”, need to contain + real size and address fields. The number of cells for these real size and + address fields need to be non-zero. + + + + “ibm,#dma-size-cells” + + property name to define the package’s dma + address + size format. + prop-encoded-array: number encoded as with + encode-int. + The property value specifies the number of cells that are used to + encode the size field of ibm dma-window properties. If the + “ibm,#dma-size-cells” property is + missing, the default value is the + “#size-cells” property for the package. + If both the + “ibm,#dma-size-cells” and + “#size-cells” properties are missing, + refer to the + “#size-cells” property definition in the + for the default value. + + + + + “ibm,#dma-address-cells” + + property name to define the package’s dma + address format. + prop-encoded-array: number encoded as with + encode-int. + The property value specifies the number of cells that are used to + encode the physical address field of ibm dma-window properties. If the + “ibm,#dma-address-cells” property is + missing, the default value is the + “#address-cells” property for the + package. If both the + “ibm,#dma-address-cells” and + “#address-cells” properties are missing, + refer to the + “#address-cells” property definition in + the + for the default value. + + + + +
+ PCI Host Bridge Nodes + This section describes the PCI Host Bridge (PHB) properties which + are added or modified for an LoPAR implementation. Refer to + for the base PCI properties and + methods. For each platform PCI Host Bridge, a + “reg” property shall be present in the + respective PCI Node. + + Note: Since the standard RTAS PCI configuration + access services do not have separate arguments identifying the PCI host + bridge to which a service applies, platforms with multiple PCI host + bridges must assign them unique bus numbers. An OS must not reassign bus + numbers if it expects to make subsequent use of the any RTAS PCI + configuration access services. + To support dynamic addition and removal of PHBs, the / node + contains the properties: + ibm,drc-types (phb), + ibm,drc-indexes ibm,drc-names and + ibm,drc-power-domains (-1's). These properties have + entries for the maximum number of dynamically reconfigurable PHBs that + the platform supports for the specific OS image. + +
+ PCI Host Bridge Properties + + For each PHB in the platform (called a PCI Bus Controller in the + PCI Bus binding), a PCI Host Bridge Node shall + be defined as a child node of the system bus, in + accordance with + . Each PCI PHB Node shall have + a Unit Address defined in the + “reg” property that is unique and + persistent from each boot-to-boot. One way for the platform to meet this + requirement is to supply a virtual Unit Address based upon a unique + identifier stored in the hardware. In this case, the size field of the + first + “reg” property phys-address, size pair + shall be zero. The following properties are modified or added by this + architecture and shall apply to each of these nodes. + Each PHB shall also have the + “used-by-rtas” property, since RTAS is + used for PCI Configuration. + + + + “ranges” [S] + + Standard + property name defines this PHB’s physical + address ranges. + prop-encoded-array: Two or more ( + child-phys, parent-phys, size) + specifications. + This property is mandatory for PCI Host Bridges in LoPAR + implementations. The property value consists of four ( + child-phys, parent-phys, size) specifications, as + described in + . + The first specification shall specify the configured address and + size of this PHB’s I/O Space. (I/O Space is shown as + “BIOn” to “TIOn” in + "Address Map" section.) The + second specification shall specify the configured address and size of + this PHB’s Memory Space. (Memory Space is shown as + “BPMn” to “TPMn” in the Common Hardware Reference + Platform Architecture.) + + + + + “model” [S] + + Standard + property name indicating this PHB’s + manufacturer, part number, and revision level. This property shall be + present if this PHB does not supply the following standard PCI + configuration properties which represent the values of standard PCI + configuration registers: + “vendor-id”, + “device-id”, and + “revision-id”. + + prop-encoded-array: Text string, encoded as with + encode-string. + The value of this property is a vendor dependent string which + uniquely identifies this PHB and is correlated to its manufacturer, part + number, and revision level. (see + for more information.) The + string value is device dependent, but shall supply information sufficient + to identify the part to a level equivalent to the level achievable via + the standard PCI configuration registers: + “vendor-id”, + “device-id”, and + “revision-id”. + + + + + “64-bit-addressing” [S] + + property name indicates this PHB’s capability + to address more than 4 GB of memory. + prop-encoded-array: <none> + This property shall be present indicating that the PHB supports + addressing more than 4 GB of memory (required for all + PHB nodes). + + + + + “external-control” [S] + + property name indicates this PHB’s ability to + support the PA external control facility. + prop-encoded-int: List of integers, each encoded as + with encode-int. + The property value, if present, is a list of Resource ID’s + the version of the PA external control facility supports. This property + shall be present if this PHB supports the PA external control facility, + otherwise the property shall be absent. + + + + + “ibm,tce-alloc-info” + + property name indicates the addresses of platform pre + allocated TCE table space. + + prop-encoded-array: One to N + phys-addr, size pair(s). The first pair represents + the memory area allocated by the platform for the TCE tables associated + with this PHB. Any subsequent pairs represent memory areas that the OS + should avoid using to minimize performance impacts. + Phys-addr is encoded as with + encode-phys the number of cells for + phys corresponds to + “#address-cells” value applicable to this + node. + size the number of cells for + size corresponds to the + “#cell-size” value applicable to this + node. + + + + + “ibm,max-completion-latency” + + property name indicates the maximum DMA Read + completion latency for IOAs under this PHB. + prop-encoded-array: Integer, encoded as with + encode-int. + This property, when present (for example, see Requirement + ), indicates the maximum DMA + Read completion latency for IOAs under this PHB, in microseconds. For + plug-in adapters, the latency value does not include latency of any + additional PCI fabric (for example, PCI Express switches) on the plug-in + adapter. + + + + + “ibm,extended-address” [S] + + property name indicates this platform supports + Peripheral Memory Spaces, Peripheral I/O Spaces, and SCA spaces above 4 + GB. + prop-encoded-array: <none> + This property must be present in all PHB nodes. + + + + + “ibm,pcie-link-width-stats” + + property name indicates the collection of PCI Express + link-width capabilities and measurements at the PE below the PHB. + prop-encoded-array: 2 integers encoded with + encode-int + The first integer represents the maximum PCI Express lane-width at + the Partitionable Endpoint. + The second integer represents the actual PCI Express lane-width at + the Partitionable Endpoint. + Implementation Note: In some cases, a PCIe device may + train at a different width depending on the speed capabilities of the + link. + + + + + “ibm,pcie-link-speed-stats” + + property name indicates the collection of PCI Express + link-speed capabilities and measurements at the PE below the PHB. + prop-encoded-array: 2 integers encoded with + encode-int. The format of each integer is identical + to the link speed encodings defined in the PCI Express Capability + Structure chapter of the + . In the 2.0 version of that + specification, it defines 0x1 = 2.5 GT/s and 0x2 = 5.0 GT/s. + The first integer represents the maximum PCI Express link-speed at + the Partitionable Endpoint. + The second integer represents the actual PCI Express link-speed at + the Partitionable Endpoint. + + + + +
+ Properties for Children of PCI Host Bridges + + The following properties are defined for PCI host bridges and their + children. + + + + “133mhz-capable” [S] + + property name: The presence of this property + indicates the device’s capability of operating at 133 megahertz. + Only present if PCI-X Status Register bit 17 is set. + + prop-encoded-array: None. + + + + + “266mhz-capable” [S] + + property name: The presence of this property + indicates the device’s capability of operating at 266 megahertz. + Only present if PCI-X Status Register bit 30 is set. + prop-encoded-array: None. + + + + + “533mhz-capable” [S] + + property name: The presence of this property + indicates the device’s capability of operating at 533 megahertz. + Only present if PCI-X Status Register bit 31 is set. + prop-encoded-array: None. + + + + + “ibm,msi-ranges” + + property name: Defines the Message Signaled + Interrupt interrupt source number (as returned by H_XIRR) range(s) + assigned to this unit using the MSI capability structure. (Note this + property is only supplied if the package is assigned one or more message + signaled interrupt numbers at boot time using the MSI capability + structure, those packages assigned level sensitive interrupts include the + standard interrupts property.) The platform firmware assigns the + interrupt source numbers in order to the first N Message Signaled + Interrupt configuration spaces of the adapter, setting the associated + configuration spaces, in accordance with the platform's hardware + configuration, to produce the interrupt source numbers specified. + prop-encoded-array: List of one or more (int-number, + range) specifications. + Int-number is the first interrupt source number in a + contiguous range of interrupt source numbers encoded as with + encode-int. + Range is the one based count of consecutive interrupt + source numbers that compose the specified range of interrupt source + numbers, encoded as with + encode-int. + + + + + “ibm,msi-x-ranges” + + property name defines the Message Signaled Interrupt + interrupt source number (as returned by H_XIRR) range(s) assigned to this + IOA function using the MSI-X capability structure. (Note this property is + only supplied if the package is assigned one or more message signaled + interrupt numbers at boot time using MSI-X capability structure, those + packages assigned level sensitive interrupts include the standard + interrupts property.) The platform firmware assigns the interrupt source + numbers in order to the first N MSI-X vectors of the IOA function, + setting the associated configuration spaces and MSI-X vectors, in + accordance with the platform's hardware configuration, to produce the + interrupt source numbers specified. + prop-encoded-array: List of one or more (int-number, + range) specifications. + Int-number is the first interrupt source number in a + contiguous range of interrupt source numbers encoded as with + encode-int. + Range is the one based count of consecutive interrupt + source numbers that compose the specified range of interrupt source + numbers, encoded as with encode-int. + + + + + “ibm,req#msi” + + property name: Defines the number of Message + Signaled Interrupts requested by the adapter as communicated in its MSI + capability structure. This number may be greater than the number of + Message Signaled Interrupts actually assigned by the firmware. + prop-encoded-array: number of requested interrupts + encoded as with + encode-int. + + + + + “ibm,req#msi-x” + + property name: Defines the number of MSI-X Interrupts + requested by the adapter as communicated in the Table Size field of the + MSI-X Capability Structure for the adapter. This number may be greater + than the number of MSI-X interrupts actually assigned by the + firmware. + prop-encoded-array: number of requested MSI-X + interrupts encoded as with + encode-int. + + + + + “ibm,connector-type” + + property name to identify the connectors associated with a built-in + IOA that supports wrap test. This property must be provided if there is + more than one connector for the same IOA on the platform. + prop-encoded-array: the concatenation, with + encode+, of an arbitrary number of text strings, + each encoded as with + encode-string. + + + + + “ibm,wrap-plug-pn” + + property name to provide the part number(s) of the wrap plug(s) + required for testing built-in IOAs with the default connector or the + connectors specified in + “ibm,connector-type”. If this property + is provided in the same node with an + “ibm,connector-type” property, there is a + one-to-one correspondence between the strings in each property. If this + property is provided without an + “ibm,connector-type” property, there is + assumed to be only one connector for the device (default connector) and + this property should contain only one string. If multiple wrap plugs may + be used with the same connector, their part numbers shall be represented + in the same string, separated by commas. + prop-encoded-array: the concatenation, with + encode+, of an arbitrary number of text strings, + each encoded as with + encode-string. + + + + + “ibm,pci-config-space-type” + + property name: Indicates if the platform supports + access to an extended configuration address space from the PHB up to and + including this node. + 0 = Platform supports only an eight bit register number for + configuration address space accesses. + 1 = Platform supports a twelve bit register number for + configuration address space accesses. + This property may be provided in all + PHB nodes and their children. + Note: The absence of this property implies the platform supports + only an eight bit register number for configuration address space + accesses. + + + + + “ibm,reserved-explanation” + + property name indicates why this PHB's + “status” property contains the value of + “reserved” or + “reserved-uninitialized”. + prop-encoded-array: Text string, encoded as with + encode-string. + The property value, when present, can have the values specified in + . + + + Values + <emphasis role="bold"><literal>“ibm,reserved-explanation”</literal></emphasis> + + + + + + + + + + Value + + + + + Explanation + + + + + + + + storage-system-io + + + Reserved for storage system product use + + + + + pcix-over-pcie + + + PCIe device is abstracted as a PCIx device in the device + tree for legacy compatibility + + + + +
+ + + + + “ibm,pe-total-#msi” + + property name defines the maximum number of Message + Signaled Interrupts (MSI plus MSI-X) that are available to the PE below + this device tree node. This number only indicates the number of available + interrupts, not the number assigned. The number assigned for an IOA may + be obtained by Function 0 (Query only) of the + ibm,change-msi RTAS call. + prop-encoded-array: Maximum number of interrupts + encoded as with + encode-int. + + + + + “ibm,ehci-boot-supported” + + property name: indicates if this IOA function for + USB 2.0 (EHCI) supports devices beneath it to be used for boot. + prop-encoded-array: None. + + + + + “ibm,pe-reset-is-flr” + + property name: The presence of this property in the + PCI Express function’s OF Device Tree node indicates that the + platform will use the Function Level Reset (FLR) of the function to reset + the function when the + ibm,set-slot-reset RTAS call is used to reset the PE, + and not the PCI Express Hot Reset. + prop-encoded-array: None. + + + + + “ibm,ddw-applicable” + + property name: The Dynamic DMA Windows option RTAS + calls may be used against the PE below this node. + prop-encoded-array: A list of three integers encoded + as with + encode-int. + This property may be provided in all PHB nodes or bridge nodes that + are the PHB’s children. Separate properties must exist for each PE + that can participate in the DDW option (exists in the node above the PE). + The existence of this property in any node, indicates that the platform + supports the Dynamic DMA Windows option for the platform and for the PE + below that node. Lack of this property in the bridge node above a PE + indicates that the DDW option RTAS calls are not applicable to that PE. + The values in the property are defined as follows: + The first integer represents the token to be used for the + ibm,query-pe-dma-window RTAS call. + The second integer represents the token to be used for the + ibm,create-pe-dma-window RTAS call. + The third integer represents the token to be used for the + ibm,remove-pe-dma-window RTAS call. + + + + + “ibm,ddw-extensions” + + property name: Extensions to the Dynamic DMA Windows + option RTAS calls may be used against the PE below this node. + prop-encoded-array: A list of integers encoded as + with + encode-int. + This property may be provided in all PHB nodes or bridge nodes that + are the PHB’s children. Separate properties shall exist for each PE + that can participate in the extensions to the DDW option (exists in the + node above the PE). The existence of this property in any node, indicates + that the platform supports the extensions to the Dynamic DMA Windows + option for the platform and for the PE below that node. Lack of this + property in the bridge node above a PE indicates that the extensions of + the DDW option RTAS calls are not applicable to that PE. This property is + designed to be extended in the future by adding integers to the end of + the list, reading software should be prepared to handle earlier versions + of the property that will have a short list as well as ignore longer + lists from later versions than it was designed to handle. The values in + the property are defined as follows: + The first integer represents the number of extensions implemented. + Subsequent integers represent values associated with each extension such + as a token for an additional RTAS call or an architectural level of an + extended interface. The value of one indicates that only a single + extension is implemented as specified by the second integer in the list. + provides the definition of the + subsequent integers as defined for the LoPAR level of the DDW + option. + + + + + ibm,h-get-dma-xlates-supported + + property name: to identify those PHBs for which + H_GET_DMA_XLATES is supported on all child LIOBNs. + prop-encoded-array: <none> + + + + + ibm,h-get-dma-xlates-limited-supported + + property name: to identify those PHBs for which + H_GET_DMA_XLATES_LIMITED is supported on all child LIOBNs. + prop-encoded-array: <none> + + + + +
+ +
+ LPAR Option Properties + + + + “ibm,dma-window” + + property name to define the bus address window + children of this bridge may use for dma. + prop-encoded-array: One ( + logical-bus-number, phys, + size) triple where the logical bus number (LIOBN) is + a one cell cookie representing the unique range of TCE entries assigned + to this bridge encoded as with + encode-int, the number of cells for + phys corresponds to the node’s + “ibm,#dma-address-cells” value while the + number of cells for + size corresponds to the + “ibm,#dma-size-cells” for this + node. + Implementation Note: Platforms that support PHB level + granularity of IO assignment to partitions place the + “ibm,dma-window” property in the PHB + node, while platforms that support slot level granularity place the + “ibm,dma-window” property in the bridge + node that creates the per slot bus isolation. + Note: The first element of the ibm,dma-window triple + (the LIOBN) is used as a parameter to firmware DMA setup routines to + identify the specific I/O address space (TCE table) to be + referenced. + + + + + “ibm,is-vf” + + property name to define that the node represents an + I/O Virtualized instance of an I/O adapter. + prop-encoded-array: A one cell value that represents the LoPAR + architectural level of the virtualization: + + + “<emphasis>ibm,is-vf</emphasis> ” Values + + + + + + + + + + Value: + + + + + Description: + + + + + + + + 0 + + + Not used + + + + + 1 + + + Per LoPAR + + + + + All others + + + Reserved + + + + +
+ + + + +
+ +
+ +
+ +
+ +
+ Memory Node + + This section defines the LoPAR modifications to the OF / + memory node. In LoPAR, the memory allocated to an OS + image may be divided into a number of allocation units called + “regions” or “Logical Memory Blocks (LMB). An OS image + may be dynamically allocated additional regions or may be asked to + release regions. Each LMB is either represented in the device tree by its + own / + memory node or by an entry in + /ibm,dynamic-reconfiguration-memory nodes (see + ). The / + memory node that refers to the storage starting at + real address zero ( + “reg” property starting at the value + zero) always remains allocated to an OS image. The client program is + initially loaded into this storage, called the RMA, that is represented + by the first value of the + “reg” property of this first / + memory node. Additional storage regions may each be + represented by their own / + memory node that includes dynamic reconfiguration + (DR) properties or by an entry in /ibm,dynamic-reconfiguration-memory nodes. + To support dynamic addition and removal of regions, the / node + contains the properties: + ibm,drc-types (MEM), + ibm,drc-indexes ibm,drc-names and + ibm,drc-power-domains (-1's). These properties have + entries for the maximum number of dynamically reconfigurable regions that + the platform supports for the specific OS image. + +
+ Properties of the memory Node + + In addition to the standard properties defined for the + /memory node, the following are required for each + node representing a dynamically allocable memory region. Platforms that + support the dynamic reconfiguration of memory regions represent each such + logical memory block with its own + /memory node. Any new memory granted to an OS image + is done so with a new + /memory node, and OS images may free memory only in + full blocks represented by one of its currently held + /memory nodes. + The value of + “#address-cells” + for this node is 1. + The value of + “#size-cells” + for this node is 0 because the children of this node do not consume any physical + address space. + The + “ibm,my-drc-index” property as defined in + + . + + + + “ibm,preservable” + + property name that denotes the platform’s + ability to preserve the contents of the storage represented by this + node. + prop-encoded-array: A integer encoded as with + encode-int that represents + the ability of the platform to preserve the contents of the storage. + All non-negative values represents the expected length of time, in + minutes, that the platform can sustain the state of the storage. A value + of 0 indicates the storage is not preservable and the client program may + not register this storage for preservation, this is the assumed state if the + “preservable” + property is not present. The largest positive number represents an indefinite + retention time as provided by such technologies as flash storage. + Negative values indicate that the storage is preservable as long as + external power is maintained, perhaps by an external battery not directly + integrated into the platform. + + + + + “ibm,preserved” + + property name that denotes the preservation state of + the contents of the storage represented by this node. + + prop-encoded-array: An integer encoded as with + encode-int that represents the preservation state of + the storage. The defined states are: + 0= The storage was not registered for preservation and thus not + preserved. This is the assumed state if the + “preserved” property is not present. This + is also the state if the platform has lost knowledge of the preservation + registration state of the storage. + 1= The storage was registered for preservation and is has been + preserved since the client program last modified it. + 2= The storage was registered for preservation, however, the + contents have not been preserved. + + + + + “ibm,expected#pages” + + property name that denotes the number of pages that + the client program is expected to use to virtually map the LMB + represented by this node. + + prop-encoded-array: An integer encoded as with + encode-int that represents the log base 2 of the + expected number of virtual pages that the client program will use to map + the LMB represented by this node. + + + + + “ibm,no-h-migrate-dma” + + property name that designates that the memory in the + memory node in which this property resides cannot + have the H_MIGRATE_DMA hcall() used against it. + prop-encoded-value: <none> this is a name only + property. + + + + +
+ +
+ ibm,dynamic-reconfiguration-memory + + This device tree node defines an alternative means to represent a + number of dynamically-reconfigurable logical memory blocks (LMBs). This + node must only be generated by OF when instructed to do so by the client + program in the ELF header. All memory which is not subject to dynamic + reconfiguration (such as the RMA) is represented in + /memory node(s). + This node is a child of root. This node does not have a unit + address or + “reg” property. + The following properties are defined. + + + + “ibm,lmb-size” + + property name that defines the size of each + dynamically reconfigurable LMB. + prop-encoded-array: An integer encoded as with + encode-phys that represents the size in bytes of each + LMB. + + + + + “ibm,associativity-lookup-arrays” + + property name that defines a lookup array in which to + find the + ibm,associativity-array property value for the + LMBs. + prop-encoded-array: The number M of associativity + lists encoded as with + encode-int, the number N of entries per + associativity list encoded as with + encode-int, followed by M associativity lists each + of length N integers encoded as with + encode-int. + This property is used to duplicate the function of the + “ibm,associativity” property in a + /memory node. Each “assigned” LMB + represented has an index valued between 0 and M-1 which is used as in + index into this table to select which associativity list to use for the + LMB. “unassigned” LMBs are place holders for potential DLPAR + additions, for which the associativity list index is meaningless and is + given the reserved value of -1. This static property, need only contain + values relevant for the LMBs presented in the + “ibm,dynamicreconfiguration-memory” node; + for a dynamic LPAR addition of a new LMB, the device tree fragment + reported by the + ibm,configure-connector RTAS function is a /memory + node, with the inclusion of the + “ibm,associativity” device tree property + defined in + . + + + + + “ibm,dynamic-memory” + + property name that defines memory subject to dynamic + reconfiguration. + prop-encoded-array: The number N of LMB list entries + defined at boot time, encoded as with + encode-int, followed by N LMB list entries. + An LMB list entry consists of the following elements. There is one + LMB list entry per LMB represented. + Logical address of the start of the LMB, encodes as with + encode-phys. This corresponds to the first words in + the + “reg” property in a + /memory device tree node. + DRC index of the LMB, encoded as with + encode-int. This corresponds to the + “ibm,my-drc-index” property in a + /memory device tree node. + Four (4) bytes reserved for future expansion of flag. + Associativity list index for the LMB, encoded as with + encode-int. This is used as an index into + “ibm,associativity-lookup-arrays” + property defined above to retrieve the associativity list for the LMB. The associativity + list corresponds to the + “ibm,associativity” property in a + /memory device tree node. + A flags word, encoded as with + encode-int. This word represents 32 boolean flags. + As of this definition, flag bits are defined to correspond to the + “ibm,preservable” and + “ibm,preserved” properties in a + /memory device tree node. This definition allows for + additional flags to be added in the future. + The following bits in the “flags word” above are + defined. + + + Flag Word + + + + + + + + Name + + + Bit Position + + + Description + + + + + preserved + + + 0x00000001 + + + If b'0', corresponds to the + “ibm,preserved” property having + a zero value. + If b'1', corresponds to the + “ibm,preserved” property having + a non-zero value, and the preserved_state bit below indicates + the state of preservation. + + + + + preservable + + + 0x00000002 + + + If b'0', corresponds to the + “ibm,preservable” property + having a zero value. + If b'1', corresponds to the + “ibm,preservable” property + having a non-zero value. + + + + + preserved_state + + + 0x00000004 + + + If b'0', corresponds to the + “ibm,preserved” property having + a 0x1 value. + If b'1', corresponds to the + “ibm,preserved” property having + a 0x2 value (and, in the old binding, the LMB having a status + of “fail”). + + + + + assigned + + + 0x00000008 + + + If b'1', this LMB is assigned to the partition as of boot + time. If b'0', this LMB is not assigned to the partition as of + boot time. + + + + + No H_MIGRATE_DMA + + + 0x00000010 + + + If b'0', corresponds to non-existence of the + “ibm,no-h-migrate-dma” in the + memory node. + If b'1', corresponds to existence of the + “ibm,no-h-migrate-dma” in the + memory node. + + + + + DRC invalid + + + 0x00000020 + + + If b'0', the DRC field of + “ibm,dynamic-memory” property + is valid. + If b'1', the DRC field of + “ibm,dynamic-memory” property + is invalid. + + + + + Associativity Index + + + 0x00000040 + + + If b'0', the Associativity List Index field of + “ibm,dynamic-memory” property + is valid. + If b'1', the Associativity List Index field of + “ibm,dynamic-memory” property + is invalid. + + + + + Reserved Memory + + + 0x00000080 + + + If b'0', corresponds to the + “status” property having a + value of “okay”. + If b'1', corresponds to the + “status” property having a + value of “reserved”. + + + + +
+ + + + + “ibm,memory-flags-mask” + + property name that defined which flags in the + “flags word” above are defined in this version of this + architecture. + prop-encoded-array: An integer encoded as with + encode-int with all flag bits recognized by this + version of this architecture having a b'1' value. For this version, the + value will be 0x000000FF. + + + + + “ibm,memory-preservation-time” + + property name that defined the time value that would + appear in the + “ibm,preservable” property in the old + bindings for a preservable LMB. + prop-encoded-array: An integer value encoded as with + encode-int that represents the expected length of + time, in minutes, that the platform can sustain the state of power for a + preservable LMB. The largest positive number represents an indefinite + retention time as provided by such technologies as flash storage. A value + zero indicates that no memory will be marked as preservable. + + + + +
+ +
+ +
+ Memory Controller Nodes + This section describes + memory-controller nodes and their properties. NUMA + configurations, have multiple + memory-controller nodes in the device tree one for + each Central Electronics Complex (CEC). In dynamic reconfiguration NUMA + environments, these + /memory-controller nodes are subject to standard + LoPAR dynamic reconfiguration operations and contain standard LoPAR + dynamic reconfiguration properties. + +
+ Memory Controller Node Properties + + No nodes of type + memory-controller shall be defined anywhere in the + device tree when the platform fully abstracts the memory controller and + the OS has no access to the memory controller (typically when running in + a partition). Otherwise, one or more nodes of type + memory-controller shall be defined as a child of + “/” (the root) and shall not have a + “ranges” property. The following + properties shall apply to each of these nodes. If the platform does not + abstract the functions of a platform's multiple memory controllers via + firmware (such as RTAS) then the platform shall + include a node of type + memory-controller for each Memory Controller in the + platform. + A Memory Controller can also have the + “used-by-rtas” property (see + ), if it has functions + abstracted by RTAS. + + + + “device_type” [S] + + Standard property name that denotes a Memory Controller + node. + prop-encoded-array: A string, encoded as with + encode-string. + The value of this property shall be + “memory-controller”. + + + + + “reg” [S] + + Standard + property name defines the base physical address and + size of this Memory Controller’s addressable register space. + prop-encoded-array: One ( + phys-address, size) pair where + phys-address is encoded as with + encode-phys, and + size is encoded as with + encode-int. + The property value shall be the base physical address and size of + this Memory Controller’s register space. + + + + + “model” [S] + + Standard property name indicating this Memory + Controller’s manufacturer, part number and revision level. + prop-encoded-array: Text string, encoded as with + encode-string. + The value of this property is a vendor dependent string which + uniquely identifies this Memory Controller and shall be correlated to its + manufacturer, part number, and revision level. (see Core document for + more information.) + + + + + “external-control” [S] + + property name indicates this Memory + Controller’s ability to support the PA external control + facility. + prop-encoded-int: List of integers, each encoded as + with encode-int. + The property value, if present, is a list of Resource ID’s + the version of the PA external control facility supports. This property + shall be present if this Memory Controller supports the PA external + control facility, otherwise the property shall be absent. + + + + + “error-checking” [S] + + Standard property name defines the error checking capability + of the node. + prop-encoded-array: a string, encoded as with + encode-string, where the value could equal + “none”, “ecc”, or “parity”. + The value of + “#address-cells” + for this node is 1. + The value of + “#size-cells” for this node is 0 because + the children of this node do not consume any physical address + space. + + + + +
+ +
+ +
+ <literal>IBM,memory-module</literal> Nodes + + Memory packaged on DIMMs or DIMM like modules are represented in + the device tree with + IBM,memory-module nodes. These nodes represent + physical packages, these packages do not necessarily map directly to a + memory address range. + No nodes of type + IBM,memory-module shall be defined anywhere in the + device tree when the platform supports dynamic VPD via the RTAS + ibm,get-vpd service. Instead the VPD that would + normally be reported via the + “ibm,vpd” property in these nodes shall + be reported by + ibm,get-vpd. + +
+ Properties for Memory Modules + + Memory modules appear as children of the + memory node or, for platforms supporting memory DR + operations (either logical or physical), the + memory-controller node of the device tree. This + section defines properties for the + IBM,memory-module nodes and additional properties for + the + memory and + memory-controller nodes. + +
+ +
+ <literal>IBM,memory-module</literal> Node Properties + + An + IBM,memory-module node is a child of the + memory node or, for platforms supporting memory DR + operations (either logical or physical), the + memory-controller node. + The + “name” + of the node is “IBM,memory-module” + The + “device_type” + of the node is “IBM,memory-module” + The + “reg” + standard property for an + IBM,memory-module node is its memory module number + which is an arbitrary OF selected enumeration. + The + “ibm,size” + property for an + IBM,memory-module node is an integer which is less + than 4GB and which by itself indicates the size of the memory module, in + bytes, if the memory module is smaller than 4GB and if + “status” is + “okay” or + “fail”. + If the memory module is larger than or equal to 4GB in size, then + the + “ibm,size-upper” + property for an + IBM,memory-module node is present in addition to the + “ibm,size” property. This property is an + integer which is multiplied times 4GB and then added to the value of the + “ibm,size” property to get the size of + the module, in bytes. The property + “ibm,size-upper” is not required if the + memory module size is less than 4GB. + The + “status” + standard property for an + IBM,memory-module node may have one of the following + string values: + + + + “okay” for a good memory module + + + + “fail” for a bad memory module + + + + “fail-no-matched-pair” for a missing + memory module if one of a pair is missing + + + + “fail-unsupport” for an unsupported + memory module + + + + “fail-partial” for a bad memory module + where part of the memory on the module is bad and has not been configured + and part of the memory is good and has been configured. + + + + + “fail-excess-memory” for + “okay” memory modules that are not + configured because they exceed the system memory addressability of the + platform. + + + + + “disabled” for a memory module that has + been manually deconfigured. + + + + + + “ibm,mem-banks” + + property name defines the number of memory banks + contained within the memory module. + + prop-encoded-array: an integer, encoded as with + encode-int, which describes whether this is a 1, 2, + or 4-bank module, with a corresponding value of 1, 2 or 4 and so on to + match the number of banks in the physical device. + + + + + “ibm,mem-type” + + property name defines the memory module type. + + prop-encoded-array: a string, encoded as with + encode-string, that describes the type of module, + with values of + “FP” (Fast Page), + “EDO” (Extended Data Out), or + “SDRAM” (Synchronous DRAM). + + + + + “ibm,mem-err-det” + + property name defines the type of error detection + mechanism supported by the module + prop-encoded-array: a string, encoded as with + encode-string, with values of + “none”, + “parity”, or + “ECC”. + + + + + “ibm,mem-speed” + + property name defines the access or clock speed + supported by the module, in picoseconds + + prop-encoded-array: an integer, encoded as with + encode-int, which describes the access or clock + speed supported by the module, in picoseconds. + + + + +
+ +
+ +
+ Interrupt Controller Nodes + + This section describes the properties for the LoPAR interrupt + controller node. If an interrupt controller node includes the + “used-by-rtas” property, then the + platform includes firmware code for accessing the interrupt + controller. + For LSIs, the platform shall adhere to the + interrupt structure OF + representation. + +
+ PowerPC External Interrupt Controller Nodes + + This section describes the properties for the PowerPC External + Interrupt Controller nodes. PowerPC interrupt controllers are normally + packaged inside other system chips, however, they are logically + represented in the device tree by two or more independent interrupt + controller nodes. Each node reports either the interrupt source layer + resources that are housed in a single Bus Unit Controller (BUC) e.g. host + bridge, or logical equivalent, or a subset of the resources associated + with the platform’s interrupt presentation layer. The node per BUC + and presentation layer subset divisions provides a foundation for dynamic + reconfiguration. + At a dynamic reconfiguration event, such as adding an IO drawer, or + removing a processor, the interrupt controller nodes associated with the + added or removed hardware will also be added or removed. Therefore. + platforms should report, in individual nodes, each interrupt controller + that occupies a separate physical package. And OSs should expect a fine + granularity of interrupt controller reporting. + + + + “ibm,interrupt-domain” + + property name that denotes a PowerPC External + Interrupt Domain + prop-encoded-array: An integer encoded as with + encode-int. + + + + + +
+ PowerPC External Interrupt Presentation Controller Node + Properties + + The following properties apply to this node. + + + + “name” [S] + + Standard + property name that denotes a PowerPC External + Interrupt Controller. + prop-encoded-array: A string, encoded as with + encode-string. + The value of this string shall be + “interrupt-controller”. + + + + + “device_type” [S] + + Standard + property name that indicates an Interrupt + Controller. + prop-encoded-array: A string, encoded as with + encode-string. + The value of this property shall be + “PowerPC-External-Interrupt-Presentation”. + + + + + “reg” [S] + + Standard + property name defines the base physical address(s) + and size(s) of this PowerPC External Interrupt Presentation layer’s + registers. + + prop-encoded-array: List of ( + phys-addr, size + ) specifications. + + Phys-addr is encoded as with + encode-phys, and + size is encoded as with + encode-int. + The entries shall represent the base address of a single set of + PowerPC External Interrupt Presentation Layer Registers of the Interrupt + Management Area. There shall be one entry for each interrupt server queue + supported by this unit. The order of the entries shall correspond to the + entries in the + “ibm,interrupt-server-ranges” property + described below. + + + + + “compatible” [S] + + Standard + property name to define alternate + “name” property values. + + prop-encoded-array: The concatenation, with + encode+, of an arbitrary number of text strings, + each encoded as with + encode-string. + The property value shall include + “IBM,ppc-xicp”. + + + + + “ibm,interrupt-buid-size” + + property name: Defines the number of bits + implemented in the concatenation of the BUID fields. + + prop-encoded-value: An integer in the range of 9 to + 20 encoded as with + encode-int. + As platforms grow in size so as to require use of larger BUIDs + (values of the + “ibm,interrupt-buid-size” + property greater than 9) the platform engineers need to interlock with their OS + providers to ensure support. + + + + + “ibm,interrupt-server-ranges” + + Property name that defines the interrupt server + number(s) and range(s) handled by this unit. + prop-encoded-array: List of (server#, range) specifications. + Server# is encoded as with + encode-int in the range of 0 - 2 + the largest value of the + “ibm,interrupt-server#-size” property contained in the device + tree. + Range is encoded as with + encode-int. + The first entry in this list shall contain the + server# associated with the first + “reg” property entry. The + server# corresponds to a value of a processor’s + “ibm,ppc-interrupt-server#s” property. + The range shall be the number of contiguous + server# s supported by the unit (this also + corresponds to the number of + “reg” entries). + + + + + “interrupt-controller” [S] + + Standard + property name to indicate an interrupt (sub-)tree + root. + prop-encoded-array: <none> The presence of + this property indicates that this node represents an interrupt + controller. + + + + + “model” [S] + + Standard + property name indicating this unit’s + manufacturer, part number, and revision level. + + prop-encoded-array: Text string, encoded as with + encode-string. + The value of this property shall be a string which uniquely + identifies the interrupt controller and shall be correlated to the + manufacturer, part number, and revision level. This value is device + dependent (see the Core document for more information). + + + + +
+ +
+ PowerPC External Interrupt Source Controller Node + Properties + + Interrupt source controller resources as represented by + “interrupt-ranges”, + “#interrupt-cells”, and + “ibm,interrupt-server#-size” properties + may be reported in stand-alone interrupt source controller nodes or in + other logical equivalent nodes which contain the + “interrupt-controller” property. The + following properties apply to these nodes. + + + + “name” [S] + + Standard + property name that denotes a PowerPC External + Interrupt Controller. + prop-encoded-array: A string, encoded as with + encode-string. + The value of this string shall be + “interrupt-controller”. + + + + + “device_type” [S] + + Standard + property name that indicates the specific flavor of + Interrupt Source Controller. + prop-encoded-array: A string, encoded as with + encode-string. + The value of this property shall be one of the following: + + “PowerPC-LSI-Source”. + For Level Sensitive Interrupt source controllers. + + “PowerPC-MSI-Source”. + For Message Sensitive Interrupt source controllers such as used + with PCI MSI. + + + + + “reg” [S] + + Standard + property name defines the base physical address(s) + and size(s) of this PowerPC External Interrupt Source if any. + prop-encoded-array: List of ( + phys-addr, size) specifications. + Phys-addr is encoded as with + encode-phys, and + size is encoded as with + encode-int. + If the + “device-type” of the interrupt source + controller is + “PowerPC-MSI-Source”, then the last + “reg” entry shall correspond to the + interrupt controller’s 4 byte Message Interrupt Input Port. + + + + + “compatible” [S] + + Standard + property name to define alternate + “name” property values. + prop-encoded-array: The concatenation, with + encode+, of an arbitrary number of text strings, + each encoded as with + encode-string. + The property value shall include + “ibm,ppc-xics”. + + + + + “interrupt-ranges” [S] + + Standard + property name that defines the interrupt number(s) + and range(s) handled by this unit. + prop-encoded-array: List of ( + int-number, range) specifications. + Int-number is encoded as with + encode-int. + + Range is encoded as with + encode-int. + The first entry in this list shall contain the + int-number associated with the first + “reg” property entry. The + int-number is the value representing the interrupt + source as would appear in the PowerPC External Interrupt Architecture + XISR. The range shall be the number of sequential interrupt numbers which + this unit can generate. + + + + + “interrupt-controller” [S] + + Standard + property name to indicate an interrupt (sub-)tree + root. + prop-encoded-array: <none> The presence of + this property indicates that this node represents an interrupt + controller. + + + + + “model” [S] + + Standard + property name indicating this unit’s + manufacturer, part number, and revision level. + prop-encoded-array: Text string, encoded as with + encode-string. + The value of this property shall be a string which uniquely + identifies the interrupt controller and shall be correlated to the + manufacturer, part number, and revision level. This value is device + dependent (see the Core document for more information). + + + + + “#interrupt-cells” [S] + + Standard property name to define the number of cells in an + interrupt-specifier within an interrupt + domain. + prop-encoded-array: An integer, encoded as with + encode-int, that denotes the number of cells + required to represent an interrupt specifier in its child nodes. + The value of this property for the PowerPC External Interrupt + option shall be 2. Thus all interrupt specifiers (as used in the standard + “interrupts” property) shall consist of + two cells, each containing an integer encoded as with + encode-int. The first integer represents the + interrupt number the second integer is the trigger code: 0 for edge + triggered, 1 for level triggered. + + + + + “ibm,interrupt-server#-size” + + property name: Defines the number of bits + implemented in the concatenation of the server#extension and server# + fields. + prop-encoded-value: An integer in the range of 8 to + 24 encoded as with + encode-int. + As platforms grow in size so as to require use of the + server#extension field (values of the + “ibm,interrupt-server#-size” + property greater than 8) the platform engineers need to interlock with their OS + providers to ensure support. + + + + +
+ +
+ +
+ +
+ Additional Node Properties + + Additional properties and methods are defined in this section for + LoPAR binding adapters and/or devices. + +
+ Interrupt Properties + + The properties in this section shall be implemented for any device + that can present an interrupt for an LoPAR platform implementation. The + platform shall adhere to the + definition for the interrupt + structure. + +
+ +
+ Miscellaneous Node Properties + + This section defines properties which support devices, adapter and + buses with geographical information. These properties shall be present + for an LoPAR platform. + + + + “built-in” [S] + + Standard property name: Any device that connects to an + industry standard I/O expansion bus attached through a non-standard + connector. + prop-encoded-string: <none>. + Note: This property will also include platform + ‘riser’ cards. + + + + + “used-by-rtas” [S] + + Standard property name: Indicates the device can be in use by + an RTAS Function Call. + prop-encoded-int: Presence of property indicates a + device may have an I/O or resource conflict with a RTAS Function + Call. + + + + + The use of the + “slot-names” property defined below is + deprecated in favor of the + “ibm,loc-code” property. + + + + “slot-names” [S] + + property name: Describes external labeling of + adapter/device connectors. + prop-encoded-array: An integer, encoded as with + encode-int, followed by a list of strings, each + encoded as with + encode-string. + The integer portion of the property value is a bitmask of available + connectors; for each connector associated with the adapter/device, the + bit corresponding to that connector’s ID number is set from + least-significant to most-significant ID number. The number of following + strings is the same as the number of connectors; the first string gives + the platform nomenclature or label for the connector with the smallest ID + number, and so on. + + Note: Each device that has a connector should + identify the order and contents of the list of strings in a + binding. + + + + + “ibm,loc-code” [S] + + property name to provide location code(s) for the + Field Replacable Unit. + prop-encoded-array: an arbitrary number of strings, + encoded as with + encode-string. + + + + + “ibm,vpd” + + property name to provide Vital Product Data (VPD) + information as defined in + . + + prop-encoded-array: the concatenation, with + encode+, of one or more pairs of elements, the first + element of each pair being an integer (representing the length of the + second element) encoded as with + encode-int, and the second element of each pair + being a series of bytes (the VPD data) encoded as with + encode-bytes. + + + + + “ibm,loc-code-map” + + prop-name to identify that the interface may have + child nodes, which may or may not be present in the device tree, that + have a physical location code based on their unit-address. + prop-encoded-array: A list of pairs (unit-address, + location-code). The unit-address is the child device node's + “reg” property string-encoded according + to the parent node's architecture and encoded as with encode-string. The + location-code is the child device node's + “ibm,loc-code” property encoded as with + encode-string. + If a child device under this node has a matching unit-address, the + location code corresponds to the physical location of that child + device. + + + + +
+ +
+ +
+ <literal>/aliases</literal> Node + + A device alias, or simply + alias, is a shorthand representation of a + device-path. + Aliases are properties of the + aliases node, encoded as with + encode-string. Aliases are typically used by a user + to facilitate not specifying a long path name at the User Interface + ‘ok’ prompt. + An implementation of OF for an LoPAR platform shall provide the + following aliases as properties of the + aliases node, if the corresponding device + exists: + + + + “disk” [S] + + property name indicating the device path of the + factory default disk that is the preferred boot disk + Implementation Note: The preferred + boot disk should be the disk + that results in the fastest boot time. Implementations might + automatically spin up a disk at system power on and provide mechanisms + for firmware to report that disk in this property. + for the platform. + + + + + “tape” [S] + + property name indicating the device path of the + factory default tape. + + + + + “cdrom” [S] + + property name indicating the device path of the + factory default CDROM. + + + + + “keyboard” [S] + + property name indicating the device path to the + keyboard to be used for the User Interface. + + + + + “mouse” [S] + + property name indicating the device path to the mouse + to be used for the User Interface. + + + + + “screen” [S] + + property name indicating the device path to the + screen to be used for the User Interface. + + + + + “pc-keyboard” [S] + + property name indicating the device path of the + factory default PC-style keyboard. + + + + + “pc-mouse” [S] + + property name indicating the device path of the + factory default PC-style mouse. + + + + + “adb-keyboard” [S] + + property name indicating the device path of the + factory default ADB-style keyboard. + + + + + “adb-mouse” [S] + + property name indicating the device path of the + factory default ADB-style mouse. + + + + + “scsi” [S] + + property name indicating the device path of the + factory default built-in SCSI device. + + + + + “com1” [S] + + property name indicating the device path of the + factory default 16550-style serial port known as + “com1.” + + + + + “com2” [S] + + property name indicating the device path of the + factory default 16550-style serial port known as “com2.” + + + + + “scca” [S] + + property name indicating the device path of the + factory default SCC-style serial port known as “SCCA.” + + + + + “sccb” [S] + + property name indicating the device path of the + factory default SCC-style serial port known as “SCCB.” + + + + + “floppy” [S] + + property name indicating the device path of the + factory default floppy drive. + + + + + “net” [S] + + property name indicating the device path of the + factory default built-in network interface controller. + + + + + “rtc” [S] + + property name indicating the device path of the + factory default real-time-clock chip. + + + + + “nvram” [S] + + property name indicating the device path of the + factory default NVRAM. + + + + +
+ +
+ <literal>/event-sources</literal> Node + The + /event-sources node describes the possible RTAS Error + and Event Classes for interrupts. The + /event-sources node shall be defined to be a child of + the root device tree node if the platform supports any event interrupts. + The following properties shall be defined for this node: + + + + “name” [S] + + Standard + property name that denotes the Event Sources. + prop-encoded-array: A string, encoded as with + encode-string. + The value of this string shall be + “event-sources”. + When events are reported as virtual interrupts there shall be a + node of + device_type + “PowerPC-External-Interrupt-Presentation” from + which the virtual interrupt source BUID size can be obtained. Also the + event-sources node represents the interrupt source + node for virtual event interrupts and thus the following properties shall + be defined for this node: + + + + + “interrupt-controller” [S] + + Standard property name: to indicate the events interrupt tree + root. + + prop-encoded-array: <none> The presence of + this property indicates that this node represents a source of virtual + interrupts. Encoded with + encode-null. + + + + + “#interrupt-cells” [S] + + Refer to the definition of the + “#interrupt-cells” property for nodes of + device_type “PowerPC-LSI-Source” for + information about the definition of this property for virtual event + interrupts. + + + + + “interrupt-ranges” [S] + + Refer to the definition of the + “interrupt-ranges” property for nodes of + device_type + “PowerPC-LSI-Source” for information + about the definition of this property for virtual event + interrupts. + Children of + /event-sources present the interrupt specifiers + associated with the reporting of platform events. LoPAR platforms have + historically implied the default value of + “#interrupt-cells” of 1 to report the + associated interrupt specifiers without the interrupt trigger specifier. + However, all new designs shall present interrupt specifiers with explicit + trigger level values. + + + + +
+ Child nodes of the Event Sources Node + + The following specify standard child nodes of the + /event-sources node. These nodes could be present in + an LoPAR platform. + Children of the + /event-sources node specify the interrupt specifiers + associated with the reporting of platform events. Interrupt designs shall + use the 1275 standard + “interrupts” property as configured to + report the interrupt specifier for the platforms PowerPC interrupt + controller. The interrupt specifiers if the + “interrupts” property indicates one or + more interrupt source numbers that are used to report event + conditions. + +
+ internal-errors + + The presence of the node indicates that all or some of the function + has been implemented and will be reported using an interrupt. + + + + “name” [S] + + Standard + property name that denotes the internal error’s + events. + + prop-encoded-array: A string, encoded as with + encode-string. + The value of this string shall be + “internal-error”. + + + + + +
+ +
+ epow-events + + The presence of the node indicates that all or some of the function + has been implemented and will be reported using an interrupt. + + + + “name” [S] + + Standard + property name that denotes the EPOW events. + prop-encoded-array: A string, encoded as with + encode-string. + The value of this string shall be + “epow-events”. + + + + +
+ +
+ ibm,io-events + + The presence of the node indicates that all or some of the function + has been implemented and will be reported using an interrupt. + + “name” S + Standard + property name that denotes the I/O sub-system + events. + + prop-encoded-array: A string, encoded as with + encode-string. + The value of this string shall be + “ibm,io-events”. + +
+ +
+ +
+ +
+ <literal>/reserved</literal> Node + + This section defines a reserved node which shall have a + “reg” property which allocates addresses + (on the bus of which it is a child) which is intended to be a place to + identify hardware registers that do not otherwise belong to a recognized + device. + + + + “name” [S] + + Standard + property name that denotes reserved addresses that do + not belong to a recognized device. + prop-encoded-array: A string, encoded as with + encode-string. + The value of this string shall be + “reserved”. + + + + + “device_type” [S] + + Standard + property name that indicates the device type. + + prop-encoded-array: Text string, encoded as with + encode-string. + The value of this property shall be + “reserved”. + + + + + “reg” [S] + + Standard + property name defines a hardware register address and + range of addresses not intended for OS (OS) use. + prop-encoded-array: List of ( + phys-addr, size) specifications. + Phys-addr is a (phys.lo ... phys.hi) sequence equal + to #address-cells, encoded as with + encode-phys. + + size is a sequence equal to + #size-cells encoded as with + encode-size. + The first entry in this list shall be a hardware register address ( + phys-addr) and a range of hardware addresses ( + size) that is not intended for OS usage. Successive + entries in this list shall be additional hardware addresses not intended + for OS usage. + + + + +
+ +
+ <literal>/chosen</literal> Node + + This section lists additional properties as required under the + /chosen node with the following text in a manner that + is consistent with + , Section 3.5. + + + + “nvram” [S] + + Standard property name that defines the package + Ihandle for CHRP NVRAM. + prop-encoded-array: an integer, as encoded with + encode-int, that is the package + Ihandle the CHRP NVRAM. + Note: The nvram Node identified in the /chosen Node + shall support a size method as specified in + , Section 7.2. The size method + will return a value that is the total platform NVRAM size. + + + + + “ibm,rpa-client-config” + + property name that defines the processed fields of + the client program’s IBM,RPA-Client-Config ELF note section. + + prop-encoded-array: an array of integers encoded as + with + encode-int, that consist of the fields of the note + section that the firmware processed prior to loading the client + program. + + + + + “ibm,architecture-vec-5” + + property name: that presents the values of the + option vector #5 negotiated by the + ibm,client architecture-support method. Presence of + this property signifies that the client program load module invoked the + ibm,client architecture-support method. + prop-encoded-array: An array of bytes having the + format of the fifth option vector from + representing the value chosen + by the ibm,client architecture-support method. + + + + + “ibm,client-architecture-support-reboot” + + property name: that indicates that one or more + reboots have occurred in this boot sequence in order to adjust the + platform settings to match the specification in the + “ibm,client-architecture-support” open + firmware method or the IBM,RPA-Client-Config ELF header note. Note this + property is not included for the first boot in a sequence. + prop-encoded-array: encoded as with + encode-int that specifies the number of reboots that + have occurred in this boot sequence in order to adjust the platform + settings to match the specification in the + “ibm,client-architecture-support” open + firmware method or the IBM,RPA-Client-Config ELF header note. + + + + +
+ +
+ <literal>/vdevice</literal> Node + + The node of type vdevice is a child of the root node. It is only + present in trees that also include the + “ibm,hypertas_functions” property. It, + and its children represent the virtualized devices that are implemented + by the platform firmware. Virtualized devices do not surface to a client + program a direct hardware interface. They do not appear to take up space + in the client program’s address map. Standard property names + associated with the + /vdevice node have special values as specified + below. + + + + “#address-cells” [S] + + Standard + property name encoded as with + encode-int that specifies the number of cells + required to represent a child bus address. Shall have the value of 1. + + + + + “#size-cells” [S] + + Standard + property name encoded as with + encode-int that specifies the number of cells + required to encode the size field of a child’s reg property. Shall + have the value of 0 indicating that no child node may actually take + physical address space. + + + + + “name” [S] + + Standard + property name string encoded as with + encode-string that defines the name of node. The + value shall be the string “vdevice”. + + + + + “device_type” [S] + + Standard + property name string encoded as with + encode-string that defines the device type of the + node. The value shall be the string “vdevice”. + + + + + “ibm,max-virtual-dma-size” + + Vendor unique + property name indicating the maximum size virtual dma + transfer size supported by the platform + prop-encoded-array: a single integer encoded as with + encode-int. + + + + + “ibm,migration-control” + + property name that indicates when platform firmware + supports the ability for an I/O server partition to delay the migration + of a partition to a different server in order to let any in progress I/O + to be completed. Specifically, this property indicates that the + DISABLE_MIGRATION and ENABLE_MIGRATION subfunctions of the H_VIOCTL + hypervisor call are supported. + prop-encoded-array: None, this is a name only + property. + + + + + “ibm,reserved-virtual-addresses” + + Vendor unique + property name indicating ranges of the client program + virtual address space that are reserved for platform use. + + prop-encoded-array: one or more pairs of + abbreviated-virtual-address, virtual-address-length specifications + representing the origin and length respectively of a reserved virtual + address range. + abbreviated-virtual-address: Consists of two integers + encoded as with + encode-int representing the high order and low order + 32 bits respectively of the 64 bit abbreviated virtual address. The full + virtual address is the abbreviated-virtual-address concatenated with 3 + low order bytes of 0x00. + virtual-address-length: Consists of a single integer + encoded as with + encode-int representing the number of consecutive 4K + pages contained within the range. + + + + +
+ Children of the <literal>/vdevice</literal> Node + + The children of the + /vdevice node represent the individual virtual + devices. + Children of the + /vdevice node that support dma operations contain a + the + “ibm,my-dma-window” property as defined + below: + + + + “ibm,my-dma-window” + + property name that defines the bus address window(s) + that this IOA may use for its dma. + + prop-encoded-array: One or more ( + logical-I/O-bus-number, phys, + size) triple(s) where the logical bus number is a + one cell cookie representing the unique range of TCE entries assigned to + this IOA encoded as with + encode-int, the number of cells for + phys corresponds to the node’s + “ibm,#dma-address-cells” value while the + number of cells for + size corresponds to the + “ibm,#dma-size-cells” for this node. The + first triple represents the TCE range available for mapping local memory, + while the second triple, if it exists, is where remote memory mapped by + remote partitions appears. The size field of the second triple shall be + equal to the size field of the corresponding remote partition’s + first triple. + The + “ibm,my-dma-window” property is the per + device equivalent of the + “ibm,dma-window” property found in nodes + representing bus bridges. + Children of the + /vdevice node share the ability to display unique + capabilities as represented by the following properties. + + + + + “ibm,async-dma-required” + + property name indicates that the virtual device + requires the use of asynchronous virtual DMA interfaces (see + for definition of asynchronous + virtual DMA interfaces). + prop-encoded-array: None, this is a name only + property. + Children of the + /vdevice node which act a a server to other virtual + client devices, display the following property. + + + + + “ibm,vserver” + + property name indicates that the virtual device is a + server to virtual devices. + prop-encoded-array: None, this is a name only + property. + + + + + “ibm,mac-address-filters” + + property name specifies the number of non-broadcast + multicast MAC filters supported by the implementation. + prop-encoded-array: an integer in the range of 0-255 + encoded as with + encode-int. + + + + + “ibm,trunk-adapter” + + property name that indicates that the virtual device + is a trunk adapter server to the logical LAN. + prop-encoded-array: None, this is a name only + property. + + + + + “ibm,illan-options” + + property name: The existence of this property is + required when any of the ILLAN sub-options are implemented and indicates + that the H_ILLAN_ATTRIBUTES hcall() is implemented, and that hcall() is + then used to determine which ILLAN options are implemented. + prop-encoded-array: None, this is a name only + property. + + + + +
+ Virtual Teletype Device + The virtual teletype device allows communication through the + platform’s attached Hardware System Console. There is one such + virtual device node for each virtual terminal enumerated by the + “ibm,termno” property. The unit addresses + of the virtual teletype devices shall correspond to the enumeration + presented in the + “ibm,termno” property. Such virtual + terminals, as represented by the + “ibm,termno” property, are intended for + the use of the client program and shall not be marked + “used-by-rtas”. Similarly they may be + “chosen” as the default input and output device. + + + + “name” [S] + + Standard + property name encoded as with + encode-string that defines the device name. The value + shall be the string + “vty”. + + + + + “reg” [S] + + Standard property name to define a unit address for the node. + One ( + phys-addr, size) pair. The + phys-addr is the unit address of the device + (corresponding to one of the virtual terminals enumerated by the + “ibm,termno” property), and the + size shall have a length of zero. + + + + + “device_type” [S] + + Standard property name encoded as with + encode-string to specify the device type. The value + shall be the string + “serial” indicating that the device + emulates a serial terminal. + + + + + “compatible” [S] + + Standard + property name encoded as with + encode-string to specify the device driver + compatibility. The value shall be one of the strings specified in + . + + + Virtual tty compatibility strings + + + + + + + + + + Compatible property String + Value + + + + + Comments + + + + + + + + + “hvterm1” + + + + Standard client virtual tty protocol + + + + + + “hvterm2” + + + + Standard server virtual tty protocol + + + + + + “hvterm-protocol” + + + + Client virtual tty protocol extended for control of + modems etc. + + + + +
+ See + for further detail on this + virtual device. + + + + +
+ +
+ Children of + <literal>/vdevice</literal> node defined in other documents + + Like children of the pci bus node, children of + /vdevice may be defined by their own binding + documents or via binding sections/tables in their device specifications. + For example, the binding information for the LoPAR Interpartition + Logical LAN, Virtual SCSI, and Virtual Terminal can be found in the + appropriate sections of this document. The virtualization of traditional + physical devices repositions their associated device tree nodes to be + children of + /vdevice. Examples include NVRAM and Real Time Clock + (RTC) devices which are defined by + . + +
+ +
+ +
+ +
+ Barrier Synchronization Facility + + This section describes the OF node that represents the optional + Barrier Synchronization Register (BSR) facility. If the platform provides + a BSR facility it provides the + ibm,bsr node as a child of + / (root). If the platform provides a client program + with multiple independent facilities, it represents each such facility + with a separate node. A given facility may have multiple representations + through parallel windows. Each window of a given facility is represented + by a separate + “reg” property value. The following + properties are the minimum required, optional support such as dynamic + reconfiguration will add properties per requirements called out in the + . + + + + “name” [S] + + Standard + property name encoded as with + encode-string that defines the device name. The value + shall be the string + “ibm,bsr” for legacy implementations and + “ibm,bsr2” for POWER8 implementations and + beyond. + + + + + “reg” [S] + + Standard + property name to define the addresses for the + facility window(s). + + prop-encoded-array: One or more ( + phys-addr, size) pair(s). The + phys-addr, encoded as with + encode-phys, is the starting address (4 K aligned) of + the window. The + size, encoded in the number of cells specified by + “#size-cells” of the parent, is the + length of the corresponding window. + + + + + “device_type” [S] + + Standard + property name encoded as with + encode-string to specify the device type. The value + shall be the string + “ibm,bsr”. + + + + + “compatible” [S] + + Standard + property name encoded as with + encode-string to specify the device driver + compatibility. The value shall be the string + “ibm,bsr”. + + + + + “ibm,#lock-bytes” + + property name: Indicates the number of lock bytes + per line of the BSR facility. + prop-encoded-array: One or more integers encoded as + with encode-int. When the facility has multiple windows, + as represented by multiple values of the + “reg” property, then there is a + corresponding number of integers, each integer representing the number of + lock bytes per line of the corresponding window. + + + + + “ibm,lock-stride” + + property name: Indicates the number of bytes between + the beginning of lock lines in the BSR facility. + prop-encoded-array: One or more integers encoded as + with encode-int. When the facility + has multiple windows, as represented by multiple values of the + “reg” property, then there is a + corresponding number of integers, each integer representing the number of + bytes to the beginning of the next lock line in the corresponding + window. + + + + +
+ +
+ Nodes of device_type <literal>“block”</literal> and + <literal>“byte”</literal> + + This section describes the OF nodes that provide access to storage + devices in block or byte commands. This applies to such nodes with and + without a + “reg” property. + + + + “ibm,write-supported” + + property name: Indicates the driver supports write + functionality and has been verified by IBM. The use of the write function + without this property is discouraged. + prop-encoded-array: None, this is a name only + property. + + + + + “ibm,16byte-cdb-supported” + + property name: Indicates the driver supports using + the 16 byte Command Descriptor Block format, which is needed to access + above 2 TB on 512 byte block-sized media. + prop-encoded-array: None, this is a name only + property. + + + + +
+ +
+ <literal>/ibm,platform-facilities</literal> + + The node of type + ibm,platform-facilities is a child of the root node. + It and its children represent the non-CPU platform computational + facilities that are available. Platform facilities do not take up space + in the client program’s address map. Standard property names + associated with the + /ibm,platformfacilities node have special values as + specified below. + + + + “#address-cells” [S] + + Standard + property name encoded as with + encode-int that specifies the number of cells + required to represent a child bus address. Shall have the value of + 1. + + + + + “#size-cells” [S] + + Standard + property name encoded as with + encode-int that specifies the number of cells + required to encode the size field of a child’s reg property. Shall + have the value of 0 indicating that no child node may actually take + physical address space. + + + + + “name” [S] + + Standard + property name string encoded as with + encode-string that defines the name of node. The + value shall be the string + “ibm,platform-facilities”. + + + + + “device_type” [S] + + Standard + property name string encoded as with + encode-string that defines the device type of the + node. The value shall be the string + “ibm,platform-facilities”. + Some platform facilities configurations allow multiple facilities + to share a common pool of interrupt server numbers. Individual operations + specify which interrupt server number from the pool shall be used to + signal completion of the operation. To represent such a configuration, + the + /ibm,platformfacilities node may either represent an + interrupt source controller for its children or the interrupt source + controller associated with the shared pool may be represented by a + PowerPC External Interrupt Source Controller Node as an additional child + node of the + /ibm,platform-facilities node + (). Additionally, the node + representing the platform facilities Interrupt Source Controller shall + contain the + “ibm,interrupt-pool” property, and all + platform facilities that share the common pool of interrupts shall + contain the + “ibm,shared-interrupt-pool” property. + + + + + “ibm,interrupt-pool” + + property name: that indicates this interrupt + controller provides a shared pool of interrupt source numbers. + property encoded array: single cell encoded as with + encode-int that represents the type of shared + interrupt pool being represented: Defined values are: 0 with all other + values reserved. + + + + + “ibm,max-async-ops-per-processor” + + property name: that indicates for the partition the + allowed maximum number of outstanding operations for the platform + facility based upon the number of processors currently allocated to the + partition. The total allowable number of such operations outstanding + across all partition processors is the product of the value of + “ibm,max-async-ops-per-processor” and the + number of nodes of type cpu in the current partition device tree. + property encoded array: single cell encoded as with + encode-int + + + + +
+ Children of the <literal>/ibm,platform-facilities</literal> Node + + The children of the + /ibm,platform-facilities node represent the + individual platform facilities. Standard property names associated with + the children of the + /ibm,platform-facilities node have special values as + specified below. Note the children of the + /ibm,platform-facilities node shall contain the + following standard properties with their standard definitions: + + + “compatible” + + + + “name” The defined Values for the + “name” property of children of + /ibm,platform-facilities are (were # is the version + number of the interface): + + + ibm,random-v# Random number generator + + + + ibm,compression-v# Compression/Decompression + engine + + + + ibm,sym-encryption-v# Symmetric encryption/decryption + engine + + + + ibm,asym-encryption-v# Asymmetric + encryption/decryption engine + + + + + + “status” + + + Optionally the children of the + /ibm,platform-facilities node may contain as + appropriate the following standard properties with their standard + definitions: + + + + “interrupts” + + + + Additionally the children of the + /ibm,platform-facilities node may contain as + appropriate the following unique properties: + + + + “ibm,resource-id” + + property name: that indicates the platform facility + resource identification handle. + property encoded array: single cell encoded as with + encode-int + + + + + “ibm,max-sync-cop” + + property name: that indicates the maximum + characteristics of the parameters for a synchronous call of the platform + facility. These characteristics are represented as a series of integers + encoded as with + encode-int that + may grow over time as platform + facilities evolve. The absence of this property indicates that + synchronous operations are not allowed for the given child. + + property encoded array: a series of zero or more or + more cells each encoded as with + encode-int. The interpretation of the series of + integers is unique per the value of the + “name” property: + + + + For the Random number generator: NULL value indicating that all + calls are synchronous + + + + For the compression/decompression engine: Two series of cells the + first series of cells represents the maximums that can be synchronously + compressed. The second series of cells represents the maximums that can + be synchronously decompressed. + + + + The first cell in each series contains the count of the number of + data length, scatter/gather elements pairs that follow – each being + of the form + + + + One cell data byte length + + + + One cell total number of scatter/gather elements + + + + + + + + For the symmetric encryption/decryption engine: the series of + cells report for each function code (FC) and mode combination the maximum + amount of data and scatter/gather list elements that can be processed + with a given key length. Thus the array consists of 1-N sub sequences + each of the form: + + + + First cell contains the FC field + + + + Second cell contains the mode field + + + + Third cell contains the count of the number of key length, data + length, scatter/gather elements triples that follow – each being of + the form: + + + One cell key bit length + + + + One cell data byte length + + + + One cell total number of scatter/gather elements + + + + + + + + + + + “ibm,max-sg-len” + + property name: that indicates the maximum byte length + of a scatter/gather list for the platform facility. + + property encoded array: single cell encoded as with + encode-int + + + + + “ibm,shared-interrupt-pool” + + property name: that provides an indirect pointer to + the node representing the shared interrupt pool used by this + facility. + property encoded array: the phandle of the node + representing the PowerPC External Interrupt Source Controller that + sources the interrupts of the shared interrupt pool used by this + facility. + + + + +
+ +
+ +
+ +
+ Symmetric Multi-Processors (SMP) + + LoPAR platforms can have Symmetric Multi-Processor (SMP) + Configurations. In addition to the processor node properties defined in + , a SMP Configuration will + utilize the + /cpus node as explained in + + +
+ SMP Platform Device Tree Structure + + OF requires that multiple instances of any device that appears more + than once in the device tree must be unique and distinguishable by means + of their + “reg” properties. For LoPAR platforms, + processors shall not be directly attached to the main physical bus (root + node (“ + / ”)). Instead, cpu devices shall be children + of the + /cpus node. + The + /cpus node shall have one child node of device type + cpu for each processor. The + ihandle of the “executing” processor + shall + be published in the + “cpu” property of the + /chosen node. + + Note: The properties of a cpu device are already + defined in + . The only change for symmetric + multiprocessor (SMP) systems is that there will be a cpu device node + under the + /cpus node for each individual processor. Other + properties of the cpu devices shall + conform with the requirements stated in + . + +
+ +
+ SMP Properties + + The following properties are for a PA SMP environment. These SMP + properties will be under the + /cpus Node. + + + + “slot-names” [S] + + property name that describes platform labeling of + plug-in cpu/processor card slots. + prop-encoded-array: An integer, encoded as with + encode-int, followed by a list of strings, each + encoded as with + encode-string. + The integer portion of the property value is a bitmask of possible + processors; for each add-in slot on the bus, the bit corresponding to + that slot’s ID number is set from least-significant to + most-significant ID number. The number of following strings is the same + as the number of slots; the first string gives the platform nomenclature + for the slot with the smallest ID number, and so on. The CPU’s + “slot-names-index” property can be used + as an index into the bitmask integer of this property. The absence of + this property indicates that no slots are present. + + + + + “smp-enabled” [S] + + property name that indicates a platform can be SMP + enabled. + prop-encoded-array: <NULL> + The presence of this property signifies that the platform is SMP + enabled, even if it only has one processor. + + + + +
+ +
+ Processor Node + + The following properties are for a PA SMP environment. This SMP + property will be under each + /cpu Node. + + + + “slot-names-index” [S] + + + property name: Identifies each cpu with a unique + number. + + prop-encoded-array: An integer, encoded as with + encode-int. + The value of this integer is a platform unique number with a range + from 0 to + n-1 for each CPU where + n is the number of slots. This number is used to + index into the + “slot-names” property to identify the + value of the string associated with the slot name. + + + + +
+ +
+ +
+ Device Power Management Properties/Methods + This section defines standard platform node properties, device node + properties, and methods related to power management. The properties and + methods of this section shall be implemented on any platform which supports + power management except where noted. However, it is still being enhanced. + OS providers who want to ensure that the data needed for their power + management policies is included should contact the authors of this + document. + +
+ System Node Properties + + The following defines properties are to be associated with the rtas + and the power-management-events nodes of the device tree. + +
+ Properties assigned to the RTAS node + + Power domains are a feature of platforms which support power + management. Within the OF device tree, power domains are represented by a + power domain identifier which is defined to be an integer in the range 0 + ... n-1, where n is the number of power domains on the platform. + + + + “power-domains-tree” [S] + + Standard + property name which defines the power domain + hierarchy for this platform. + + prop-encoded-array: An array of integers, each + encoded as with + encode-int, that is a flattened representation of + the power domain dependency tree. + The array consists of a number of tuples, one for each power domain + defined on the platform. Each tuple consists of the power domain + identifier domain#, followed by the number of power levels #levels + supported by the domain, followed by an array of tuples, one for each + level. These tuples consist of a level identifier level, followed by the + number of power sources from which the domain draws power, followed by an + array of tuples (power-source-id, power). The power domain tuple is + terminated by the number of children #children followed by a list of the + domain identifiers of each child. The power values are expressed in + milliamperes and include only the power consumed by support logic not + represented as devices in the device tree including any RTAS abstracted + devices within the particular power domain. + + + + + “power-domains-controllers” [S] + + Standard + property name which defines the power domain + controllers present on this platform. + + prop-encoded-array: an array of integers, each + encoded as with + encode-int. + Each integer is the + phandle of the device tree node that functions as the + power domain controller for a domain. A single controller may serve as + the control point for multiple domains (the architecture calls them power + domain control points). Each device which serves as a controller encodes + the + “controls-power-domain” property. + + + + + “power-domains-names” [S] + + Standard + property name used to define the user readable names + for the power domains. + + prop-encoded-array: an array of strings, each + encoded as with + encode-string, that are the user readable names for + the domains. + The number of strings matches the number of domains and there is a + one-to-one correspondence between the entries in the + “power-domain-controllers” property and + the entries in this array. + + + + + “platform-power-sources” [S] + + Standard + property name defining the platform power + sources. + + prop-encoded-array: an array of integers, each + encoded as with + encode-int. + The array is structured as a number of tuples. Each of these tuples + consists of the values source-voltage, (given in millivolts), peak-power, + continuous-use-power (both expressed in milliamperes supplied at the + stated voltage), and conversion-efficiency (expressed in percent). + + + + + “power-sources-names” [S] + + Standard + property name defining the platform power source + names. + + prop-encoded-array: an array of strings, each + encoded as with + encode-string, that are the user readable names for + the power sources. + The number of strings match the number of power sources and is in + one-to-one correspondence to the entries in the + “platform-power-sources” property. + + + + + “platform-battery-sources” [S] + + Standard + property name defining the batteries utilized by a + platform. + + prop-encoded-array: an array of integers, each + encoded as with + encode-int. + Each value in this array is the manufacturer’s rated capacity + of the battery expressed in milliwatt-hours. + + + + + “battery-sources-names” [S] + + Standard + property name defining the human-readable identifier + of the batteries utilized by a platform. + + prop-encoded-array: an array of strings, each + encoded as with + encode-string. + Each entry in this array corresponds one-for-one with the batteries + defined in the + “platform-battery-sources” property. + + + + +
+ +
+ Properties of the power-management-events node + + + + “power-type” [S] + + Standard + property name defining the power management event + types implemented on a specific platform. + + prop-encoded-array: an array of integers, each + encoded as with + encode-int. + + + + +
+ +
+ +
+ Device Properties + + + + “power-domains” [S] + + Standard + property name, indicating the power domains of which + this device is a member. + + prop-encoded-array: List of one or more + domain-id’s to which this device belongs. + Domain-id’s is encoded as with + encode-int. + The + “power-domains” property should only list + the + domain-id’s of the lowest power domain tree + nodes in which this device has membership. If the device is a member of + the default power domain 0 alone, this property does not need to be + provided. + + + + + “device-power-states” [S] + + Standard + property name which describes the power states this + device supports. + + prop-encoded-array: An array of integers, each + encoded as with + encode-int that defines the supported power states + for this device. + This property shall be provided for each physical device which has + multiple power states, if platform firmware provides device power state + information. + The array consists of an integer representing the initial device + power state after reset, followed by the number of power sources from + which the device draws power, followed by an arbitrary number of tuples, + one for each supported power state of the device. Each tuple consists of + the state, followed by an array of tuples (power-source-id, power) giving + the average power consumption from each power source during active use. + This is followed by another array of tuples (power-source-id, power) + giving the idle power consumption for each power source. Each power state + tuple is terminated by the maximum expected power usage lifetime in + seconds for the device if it were to remain in that state. The value + power is stated in the millamperes consumed at the voltage supplied by + the power source. + The value state shall be further constrained to have the following + semantics: + + + Semantics of device state values + + + + + + + + + + Value + + + + + Semantics + + + + + + + + 100 + + + This is the device’s most responsive state. + + + + + 20-99 + + + The device is functional. The range represents a range of + performance. + + + + + 11-19 + + + Reserved + + + + + 10 + + + Device is not operational, but retains its internal + functional parameters. + + + + + 1-9 + + + Reserved + + + + + 0 + + + Device not functional, may lose internal functional + parameters. + + + + +
+ The semantics of device power states may be further defined by + device type specific bindings. + The interaction of the defined semantics of device power state and + domain power level is defined in + . Those combinations not marked + are disallowed. + + + Combinations of Device Power State/Domain Power + Level + + + + + + + + + + + + + +   + + + + + Device Power State + + + + + + + +   + Domain Power Level + + + Full On + + + Allowed + + + Allowed + + + Allowed + + + Allowed + + + + + Reduced + + +   + + + Allowed + + + Allowed + + + Allowed + + + + + Freeze + + +   + + +   + + + Allowed + + + Allowed + + + + + Off + + +   + + +   + + +   + + + Allowed + + + + +
+ + + + + “device-state-transitions” [S] + + Standard + property name that describes the legal power state + transitions supported by the device. + + prop-encoded-array: an array of integers, each + encoded as with + encode-int that defines the legal power state + transitions for this device. + The array is structured as a number of tuples, one for each + possible transition. Each tuple consists of the starting state, followed + by the destination state, followed by an array of tuples + (power-source-id, power), one for each power source, followed by the time + required to make the transition in microseconds, followed by the maximum + count allowed for this transition. The starting state and destination + state are values defined in the + “device-power-states” property. The value + power is stated in the millamperes consumed. This property shall be + provided if platform firmware provides device power state + information. + + + + + “power-sources” [S] + + Standard + property name which designates this device as a + consumer of power sourced from a defined power source. + + prop-encoded-array: an array of integers, each + encoded as with + encode-int that gives the list of power sources to + which this device is connected. + The values are indices into the platform-power-sources data + structure. This property shall be provided if platform firmware provides + device power state information. + + + + + “power-management-mapping” [S] + + Standard + property name that defines device power states and + commands. + + prop-encoded-array: an array of integers as encoded + with + encode-int. + This optional property provides a device dependent mapping between + device power state and commands which the device driver sends to its + device. Also provides information concerning which device power states + are supported for each of the four domain power levels. See the device + type binding for a definition of the property value. + + + + +
+ Properties for Power Domain Control Points + + The following are specific to devices which can act as power domain + control points. + + + + “controls-power-domains” [S] + + Standard + property name which designates the domains over which + this device exercises control. + + prop-encoded-array: an array of integers, each + encoded as with + encode-int that defines the domains for which this + device can act a power domain control point. + A single device may serve as multiple logical control + points. + + + + +
+ +
+ +
+ Power Management Related Methods + This section defines methods associated with device tree nodes + which serve as power domain controllers (the architecture calls them + control points). + + + + set-power-level (domain# level -- actual-level) [M] + + This method is only present for power domain controllers. The + domain# is the power domain whose power level is altered, and level is + the desired level. actual-level reports the level to which the domain was + actually set. + + + + + get-power-level (domain# -- level) [M] + + This method is only present for power domain controllers. The + domain# is the power domain that is being queried. level is the current + level at which the domain is now operating. + + + + + system-off (--) [M] + + Method to turn the system off. This method is attached to the root + node of the device tree and is only present in a platform with software + control over system power. + + + + +
+ +
+ +
+ Configuration of Platform Resources + + Any computer platform is composed of standard components which are + invariant (platform ‘built-in’ standard I/O and power + management), optional components which are detectable (a second processor, + for example), and configurable components which are self-identifying + (system memory, for example). Most computer platforms also provide one or + more industry standard I/O buses which allow the insertion of specialized + functional adapter cards. These buses generally support a method for + automatic identification, interrogation, and option selection of installed + adapter cards. + A Platform shall + also have the capability of configuring power + management resources, if power management is implemented by the platform, + as defined in + . + +
+ Power Management Resource Configuration + + For a platform which supports device power management, all platform + power management related information shall be resident in the OF device + tree prior to the transfer phase of software operation (see the + definition of transfer phase in + ). Dummy devices shall be + placed in the device tree for all standard I/O bus connectors which are + not in use to provide a node to assign the slot-names, power-domains, and + power-sources properties. + Ultimately, the goal is that pluggable devices would not only + identify themselves to platform firmware but would also provide all + applicable power management related information. As an interim solution, + a utility shall be provided either in the platform firmware ROM or + supplied as a loadable OF utility on external media. This utility + interacts with a person to obtain power management information concerning + plug-in adapters and peripherals. + +
+ Power Management Information Utility + + Any platform capable of being expanded via the addition of + power-managed devices shall provide a device power management information + utility. The purpose of the utility is to allow a person (end-user or + system developer) to enter power management related device properties of + plug-in adapters and peripherals which have no mechanism to automatically + report this information to firmware or system software. The need for this + utility will disappear as standard protocols are developed for + interrogating pluggable adapters and devices to provide power management + related information. + In the most general case, the devices to be added to a node + representing a standard bus or I/O port are in the form of multilevel + subtrees. The root of this subtree specifies the path to the node in the + device tree where the subtree is to be grafted. + The utility determines the path to the node at which to graft the + new devices by interacting with a person to receive the information. The + utility uses the + “slot-names” property to identify the + location of the device for which it needs information. For example, the + utility might prompt the user with, “Enter the name of the first + device attached to the external scsi connector labeled + ‘SCSI1’.” + A data structure describing the subtree is stored in NVRAM. The + root node of this subtree contains an + “in-graft-node” property which specifies + the path to the parent node where the subtree is to be grafted into the + OF device tree. + As adapters and devices are enhanced to support the automatic + reporting of power management information the parent node would supply a + method query-power-management-attributes which can be used by firmware to + obtain this information without the need for this utility. Any + information obtained by direct device interrogation may update that + supplied via the PM NVRAM partition. + +
+ +
+ PM Configuration Process + + When the platform is booted after a configuration change and the + newly inserted adapter does not support the automatic reporting of power + management information, firmware should prompt the user asking if he + wishes to supply this information or potentially forfeit some or all of + the power management capabilities of the device. + The utility records the information it obtains in the NVRAM Power + Management Configuration Partition (NVRAM Signature of 0x71 and name + pm-config). On a subsequent reboot, platform + firmware uses the information saved in NVRAM to fill out the device tree + adding new nodes and their properties, as well as adding properties and + updating the values of properties of existing device tree nodes. + +
+
+ PM Configuration Format + + The NVRAM power management configuration partition is designed to + be accessed primarily by firmware, but the partition is designated global + and the format is specified to allow a third party to write a power + management information utility which runs on the booted OS. + The data field of the power management NVRAM partition shall be + defined as follows: + The data field is composed of a header, followed by a number of + fixed length data blocks, and finally a variable length property list + area. The length of the header and each data block is 8 bytes. The data + blocks use 16-bit integer offsets into the partition as pointers to the + data blocks and into the property list area. The base of this offset is + the beginning of the partition. This effectively limits the size of the + PM configuration area to 64 KB. If more space is required, additional PM + configuration partitions may be provided. Each pointer into the property + list area locates the start of a NULL-terminated string which represents + a list of property name/value pairs. + The following table specifies the format of the header: + + + Power Management Configuration Data Header + + + + + + + + + Field + + + + + Size + + + + + Description + + + + + + + + Version + + + 1 byte + + + Designates the version of the PM Partition data area + format + + + + + Subtree_ptr + + + 2 bytes + + + Pointer to the first data block which describes a device + subtree + + + + + Property_ptr + + + 2 bytes + + + Pointer to first data block which describes a property + list to be added to the base platform device tree + + + + + Reserved + + + 3 bytes + + + Reserved + + + + +
+ The PM Partition data area format value shall be 1. + The following table specifies the format of the data blocks: + + + Data Block Format + + + + + + + + + Field + + + + + Size + + + + + Description + + + + + + + + Block_type + + + 1 byte + + + Designates the data block type + + + + + Data Block Data + + + 7 bytes + + + Remainder of data block, format specific to data block + type + + + + +
+ Two data blocks are defined: one defining a device node and a + second defining properties to be added to the base platform device + tree. + The data block type field shall have the value 1 for a data block + which describes a device node. The data block type field shall have a + value 2 for a data block which describes a property. + + + Node Data Block Format + + + + + + + + + Field + + + + + Size + + + + + Description + + + + + + + + Block_type + + + 1 byte + + + This field shall contain the value 0x01 + + + + + Prop_list_ptr + + + 2 bytes + + + Pointer to a NULL terminated string containing the + property list for this node + + + + + Child_ptr + + + 2 bytes + + + Pointer to a data block defining a child node of this + node. This pointer will be equal to 0x0000 if this node has no + children. + + + + + Sibling_ptr + + + 2 bytes + + + Pointer to a data block defining a sibling node of this + node. This pointer will be equal to 0x0000 if this node has no + siblings. + + + + + Reserved + + + 1 byte + + + Reserved + + + + +
+ + + Property Data Block Format + + + + + + + + + Field + + + + + Size + + + + + Description + + + + + + + + Block_type + + + 1 byte + + + This field shall contain the value 0x02 + + + + + Node_path + + + 2 bytes + + + Pointer to a NULL terminated string giving the path name + of the node to which the designated property list + belongs. + + + + + Property_list_ptr + + + 2 bytes + + + Pointer to a NULL terminated string containing the + property list to be assigned to the designated node. + + + + + Reserved + + + 3 byte + + + Reserved + + + + +
+ The first node of a subtree shall have a + “name” property equal to “/” + and shall specify the + “in-graft-node” property. The child_ptr + of this data block points to the first in a list of data blocks which + describe the nodes which make up the subtree to be grafted onto the + system tree. + The final area of the partition is a set of NULL terminated strings + which represent property name/value pair lists. The last string in this + area will be terminated by at least two NULL bytes. The property list for + each node shall provide all the required PM properties and their values. + These include + “power-domains”, + “device-power-states”, + “device-state-transitions”, + “power-sources”, + “power-management-mapping”, and + “controls-power-domains”. +
+ +
+ +
+ +
+ Client Program Requirements + For LoPAR platforms, the client program requirements are defined in + , with the following + modifications. OF Client Programs for an LoPAR platform shall execute in + 32-bit mode with an OF cell size of 1. + +
+ Load Address + + The client’s load address is specified by the value of the + load-base Configuration Variable. The value of + load-base defines the default load address for + client programs when using the + load method. + Load-base shall be a real address in real mode or a + virtual address in virtual mode. Note that this address represents the + area, within the first LMB, into which the client program file will be + read by + load; it does not correspond to the addresses at + which the program will be executed. All of physical memory from + load-base to either the start of OF physical memory + or the end of physical memory, whichever comes first, shall be available + for loading the client program. + + Note: The load-base address represents the area into + which the client program will be read by load and does not correspond to + the address at which the program will be executed. +
+ +
+ Initial Register Values + + The “Initial Register Values” specified in the PA + Binding (see + ) are modified as + follows: + + + r3 -- shall be 0 on client program entry + + + + r4 -- shall be 0 on client program entry + + +
+ +
+ I/O Devices State + + With the exception of the stdin and stdout devices, OF shall close + all devices with the following conditions true: + All Devices - no DMA and not interrupting + Normal I/O Devices - not responding to access PCI + Adapter/Devices + HOST Bridges - responding to config cycles and passing through + config cycles to children + RTAS Devices - contract with OF to leave in state to perform + intended function +
+ +
+ Client Program Format + + The data format of a client program compliant with this + specification shall be either ELF (Executable and Linkage Format) as + defined by + , and extended by + , or PE (Portable Executable) + as defined by + . The standard ELF format + contains explicit indication as to the program's execution modes (e.g., + 32- or 64-bit, Big- or Little-Endian). LoPAR only supports the 32-bit + version (i.e., ELFCLASS32) for 32 and 64 bit platforms. + + Note: Other client program formats may be supported, + in an implementation specific manner, by an OF implementation. + A standard client program shall be statically linked, requiring no + relocation of the image. The program's entry point (e_entry) shall + contain the address of the first PA instruction of the client program. It + is the responsibility of the client program to establish the appropriate + value of the TOC (r2), if necessary. + + Note: The entry point is the address of the first + instruction of the client program, not that of a procedure + descriptor. + +
+ ELF-Format + This section defines how OF recognizes and prepares to execute an + ELF-Format Program. + +
+ ELF Note Section + + Part of the process of loading a client program involves verifying + its environmental requirements (e.g., endian-ness and address translation + mode) against the current firmware configuration. The client’s + endian-ness can be directly determined by examining the ELF EI-DATA + value; ELFDATA2LSB (1) implies Little-Endian while ELFDATA2MSB (2) + implies Big-Endian. However, the other client requirements (e.g., address + translation mode) are defined by means of an ELF Note Section (PT_NOTE), + pointed to by the program header. The following describes the format of + the Note Section for a client program file. + As defined by + , an ELF file can be + “annotated” by means of Note Sections within the executable + file. A Note Section contains a “header” followed by a + (possibly NULL) “descriptor”, as follows: + + + + + + + + + + + + + + Note: The endian format of the values corresponds to + the endian-ness specified by the EI-DATA field of the file. + The format of a Note Section header can be described by an OF + struct as: + struct \ Note Section header for OF + /L field ns.namesz \ length of ns.name, including NULL + /L field ns.descrsz + /L field ns.type + 0 field ns.name \ NULL-terminated, /L padded + +
+ 1275 PowerPC Note Definition + + The ns.name field of the PowerPC OF Note Section shall be + “PowerPC”; the ns.type field n shall be + 0x1275. + Following the Note Section header is a descriptor (desc); the + length (in bytes) of the descriptor is specified by a word in the Note + Section’s header (descsz). The interpretation of the descriptor + depends upon the kind of Note Section in which it is contained. For the + PowerPC OF note, the format of the Note Section’s descriptor can be + described by an OF struct, as follows: + struct \ Note Section descriptor for CHRP OF + /L field ns.real-mode + /L field ns.real-base + /L field ns.real-size + /L field ns.virt-base + /L field ns.virt-size + /L field ns.load-base + If the + ns.load-base value is not -1, then that value is + compared against the current value of the + load-base configuration variable. If they are equal + no further action is taken. If they are not equal then the + load-base configuration variable is set to the value + of + ns.load-base and the system is rebooted. + + Note: DATA field of the file. +
+ +
+ 1275 IBM,RPA-Client-Config Note Definition + + The ns.name field of the LoPAR Client Program Configuration Note + Section shall be + “IBM,RPA-Client-Config”; the ns.type + field shall be 0x12759999. + The format and requirements associated with this ELF Note Section + are designed to allow for expandability of the section definition (by + adding fields to the end of the section) while retaining forward and + backward compatibility for both the 1275 firmware and Client Program. + When the 1275 firmware code recognizes the + “IBM,RPA-Client-Config” note, it creates + a property named + “ibm,rpa-client-config” within the + /chosen node reads into this property and interprets + the lesser of the descriptor size or the maximum size of the descriptor + that was defined when the firmware was built. Should the note contain a + smaller descriptor than was defined when the firmware was built, the + firmware assumes default values for the missing descriptor fields. In + this way, new fields may be defined, and the four cases of + firmware/client program work as follows: + New Firmware/New Client Program: + Client Program Header Note contains old plus new fields. + Firmware reads all the new header and places it in + “ibm,rpa-client-config” property. + Client Program gets feed back that new fields were interpreted by + reading property in + /chosen. + Old Firmware/Old Client Program: + Client Program Header Note contains old fields. + Firmware reads all the old definition header and places it in + “ibm,rpa-client-config” property. + Client Program gets feed back that the expected fields were + interpreted by reading property in + /chosen. + New Firmware/Old Client Program: + Client Program Header Note contains only old fields. + Firmware reads only the descriptor length defined in the note + header, and places it in + “ibm,rpa-client-config” property. + Client Program gets feed back on the fields that were interpreted + by reading property in + /chosen. + Firmware uses default values for any missing fields. + Old Firmware/New Client Program: + Client Program Header Note contains old plus new fields. + Firmware reads only the length that it was defined when it was + built, and places it in + “ibm,rpa-client-config” property. + Client Program gets feed back that new fields were interpreted by + reading property in + /chosen, those missing fields indicate function not + implemented by the platform. + Following the Note Section header is a descriptor (desc); the + length (in bytes) of the descriptor is specified by a word in the Note + Section’s header (descsz). The interpretation of the descriptor + depends upon the kind of Note Section in which it is contained. For the + ELF header note named IBM,RPA-Client-Config of type 1275, the format of + the Note Section’s descriptor can be described by an OF struct, as + follows: + + + + Note: The size of the /L field is based off of + e_ident (EI_CLASS) i.e. is 4 for ELFCLASS32. + The + ns.lparaffinity field is a binary flag whose valid + values are 0 or 1. If the field is not one of these valid values the + value is assumed to be 0. If the character value is 1, the client program + requests that the platform provide all available affinity + information. + The + ns.min-rmo field specifies the minimum amount of real + mode addressable storage (in bytes times 2 + 20) that the client program needs to operate. The + ns.min-rmo-percent field specifies the minimum + percentage (valid values 0-100) of storage that must be real mode + addressable for the client program to operate. The platform shall start + the client program with a quantity of real mode accessible storage + (starting at location 0) of at least the ceiling of these two + values. + The + ns.max-pft-size field value specifies the largest + hardware Page Frame Table (in bytes times + 2 + ns.max-pft-size) that the client program can + support. The firmware shall not start a client program with a PFT larger + than this amount The minimum value is 18, the platform ignores the field + if the value is less than 18 and uses the platform defined default + value. + The + ns.splpar field is a binary flag whose valid values + are 0 or 1. If the field is not one of these valid values the value is + assumed to be 0. If the field’s value is 1, the client program + supports running in shared processor logical partitioning mode. If the + character value is not 1 and the partition is running in shared processor + mode, platform firmware reports a platform-specific error code and halts + the boot. However, if the client-program does not contain an + IBM,RPA-Client-Config + note, firmware assumes the OS supports shared + processor logical partition mode. This exception only applies to the + ns.slpar field. + The + ns.min-load field specifies the minimum amount of the + client program load module that must be loaded at + load-base. If this value is a -1 then the entire + load module must be loaded starting at + load-base else the client program load fails. The + default value is assumed to be -1. If the value of is greater than the + platform can support client program load fails. Given that the platform + can load the minimum amount of the client program load module at + load-base, it loads the amount up to the boundary + specified by + ns.min-load starting at + load-base, then it loads the rest of the load module + into contiguous storage at a location selected by platform firmware + (default, if possible, is that the residual is loaded immediately + following the first segment resulting in a single segment load). + The + ns.new-mem-def field is a flag which indicates if the + ibm,dynamic-reconfiguration-memory representation of reconfigurable + memory may be used. The default value 0x00000000 indicates the new + definition may not be used. The value 0x00000001 indicates the new + definition may be used. All other values are reserved for future + use. + The + ns.large-page-ready field is a flag which indicates + if the partition OS is prepared to support large pages. The default value + 0x00000000 indicates that the OS is not prepared for large pages. The + value 0x00000001 indicates that the OS is prepared for large pages. All + other values are reserved for future use. + If this variable indicates that the OS is not prepared for large + pages and large pages are present in the partition configuration, + platform firmware reports a platform-specific error code which indicates + this mismatch between the partition configuration and the OS + capabilities, removes all large pages from the device tree, and continues + the OS boot. + If the value of the + ns.ignore-my-client-config variable is 0x00000001, + platform firmware must not examine the value of + ns.large-page-ready until the client program calls + the PROCESS-ELF-HEADER method. The decision to continue boot should then + be made based on the value of the + ns.large-page-ready flag in the updated ELF head + passed by this method. + The + ns.force_alpha_mode field is a flag which indicates + that a non-HMC managed I/O services partition with partition management + support (VMC) configuration is being requested. The default value of + 0x00000000 indicates that the client expects to run in a configuration + which is not an I/O services partition configuration. If the partition + configuration is not compatible with this setting, the system will be + rebooted as a single partition which owns all of the system resources. On + reboot, the original partition configuration will be reinstated. The + value 0x0000001 indicates that the client is expecting to be executed in + a non-HMC managed I/O services partition with partition management + support (VMC). If the partition is not in this mode, the system will be + rebooted in this mode. In the case that the ns.force_alpha_mode flag is + compatible with the partition configuration, the boot process will + continue. This flag will be ignored when the system is HMC + managed. + +
+ +
+ +
+ Recognizing ELF-Format Programs + + The + init-program shall recognize client program images + that conform to all the requirements listed below as + “ELF-format” programs. + In the description below, field names refer to fields within the + ELF “file header” structure, which is assumed to begin at + load-base, and offsets are relative to the beginning of that structure. + Multi-byte numerical fields are interpreted according to the endianess + specified by the “data” field at offset 5. + + + + The “e_ident” field (at offset 0) contains the + string “\7fELF”, where '\7f'’ is a byte whose value is + (hex) 7f. This indicates the beginning of an ELF file header. + + + + The “EI_CLASS” field (at offset 4) contains the + value 1. This indicates the 32-bit variant of the ELF format. + + + + The “e-type” field (at offset 16) contains the + value 2. This indicates that the ELF image is executable. + + + + The “e_machine” field (at offset 18) contains the + value 20. This indicates that the ELF image is for the PA instruction + set. + + + + The “e_version” field (at offset 20) contains the + value 1. + + + + The “e_flags” field (at offset 36) contains the + value 0. + + + +
+ +
+ Preparing ELF-Format Programs for Execution + + Upon recognition of the client program image at load-base as an + ELF-format program, init-program shall prepare the program for execution + by performing the following sequence of steps. + In the description below, the fields mentioned by name are within + ELF “program header” structures, unless specified + otherwise. + + + + Search for an ELF “note” section of type + “1275” as defined in the section “ELF Note + Section”. If one is found, and the values specified by its + descriptor do not match the firmware's current operating mode, set the + appropriate configuration variables to the values specified in the note + section descriptor, and restart the firmware so that it will re-execute + the + boot command that resulted in the execution of + init-program. + + + + Set the p_paddr field for each PT_LOAD segment equal to its + p_vaddr field value if + real-mode? is false and p_paddr is -1. This + effectively maps these segments v=r. + + + + Allocate and map, if required, sufficient physical memory for + all program segments of type PT_LOAD (i.e. whose “p_type” + field contains the value 1) listed in the ELF image's program headers. + Note that all PT_LOAD program segments that have a p_paddr value that + matches their location in physical memory need not be moved, but the + memory that they occupy must be claimed. This special case is added to + allow large program images to be loaded without the 2x memory required to + move the segments. + + + + Copy the program headers to a “safe” location to + guard against the possibility of them being overwritten by the following + steps. + + + + For each program segment of type “PT_LOAD”: + + + + Copy, if required, the initialized portion of the program + segment from its current location in the loaded image to the location + given by the section's “p_paddr” field. + + + + Fill the rest of the segment with zero bytes (i.e., fill + “p_memsz - p_filez” bytes beginning at the address + “p_paddr + p_filesz”). + + + + If real-mode? is false, then map the program segment to + the virtual address specified by p_vaddr. + + + + + + Set the saved program state so that subsequent execution of + “go” will begin execution at the address + given by the “e_entry” field in the ELF file header. The + e_entry field is a physical address if + real-mode? is + TRUE and is a virtual address if + real-mode? is + false. + + + + The implementation need not take precautions to ensure that the + process of copying and zeroing program segments does not overwrite the + portions of the load image that have not yet been copied. In order to + guarantee correct copying, the value of the + load-base configuration variable and the destination + addresses of the various sections must be such that such overwriting does + not occur. One sufficient condition is that the region of memory + beginning at + load-base, of size equal to the size of the loaded + image, be disjoint from the regions of memory to which the program + segments are copied and zero-filled. Another sufficient condition is to + specify a + load-base in the Notes Section (PT_NOTE) that ensures + that the PT_LOAD segments are loaded at the address required by their + program headers and thus are not moved. There are other less-stringent + sufficient conditions, especially for simple ELF images with a small + number of program segments that are to be copied to contiguous + regions. + An implementation shall permit the ELF image to contain other + program segments in addition to those described above, but need not take + any action beyond that defined above as a result of the presence of such + other program segments. + An implementation shall ignore all ELF sections. ELF sections are + intended for binders, not loaders. Note that the CHRP ELF Note Section is + actual an ELF segment of type PT_NOTE and thus the above does not apply + to it. +
+ +
+ +
+ +
+ Additional Client Interface Requirements + + This section describes processor assist callbacks for real and + virtual memory management and a service. + +
+ Client Interface Callbacks + + This section describes callbacks for memory management. These + callbacks are provided by the client. + +
+ Real-Mode Memory Management Assist Callbacks + + + + claim_mem + + IN: [address] min_addr, [address] max_addr, size, align + OUT: throw-code, error, [address] real_addr + Allocate contiguous physical memory between min_addr and max_addr + of size bytes (128KB max for an area in the 0 to 16MB address range), + with align alignment. The alignment boundary is the smallest power of two + greater than or equal to the value of align; an align value of 1 + signifies one-byte alignment. A non-zero error code shall be returned if + the mapping cannot be performed. If error code is zero (i.e. allocation + succeeded) the routine returns the real address (real_addr) of the + physical memory block which was allocated for OF. + + + + + release_mem + + IN: [address] phys, size + OUT: throw-code + Free size bytes of physical memory starting at real address phys, + making that physical memory available for later use. That memory must + have been previously allocated by claim_mem. + + + + +
+ +
+ Virtual Address Translation Assist Callbacks + + + + alloc_virt_mem + + IN: size + OUT: throw-code, error, [address] virt_addr + Return the virtual address of a virtual memory area of size bytes + aligned to a doubleword (8-byte) boundary. A non-zero error code shall be + returned if the allocation cannot be performed. If error code is zero + (i.e. allocation succeeded) the routine returns the virtual address + (virt_addr) of the memory block which was allocated. + + + + + free_virt_mem + + IN: [address] virt_addr, size + OUT: throw-code + Free memory allocated by alloc_virt_mem. The values virt_addr and + size must correspond with memory previously allocated by + alloc_virt_mem. + + + + + claim_virt + + IN: size, align + OUT: throw-code, error, [address] virt_addr + Allocate a memory area of size bytes and alignment align. The + alignment boundary is the smallest power of two greater than or equal to + the value of align; an align value of 1 signifies one-byte alignment. A + non-zero error code shall be returned if the allocation cannot be + performed. If error code is zero (i.e. allocation succeeded) the routine + returns the virtual address (virt_addr) of the memory block which was + allocated. + + + + + release_virt + + IN: [address] virt, size + OUT: throw-code + Free size bytes of virtual memory starting at virtual address virt, + making that physical memory and the corresponding ranges of virtual + address space available for later use. That memory must have been + previously allocated by claim_virt. + + + + +
+ +
+ +
+ Client Interface Services + OF shall provide the following + Client Interface Service: + + + + test-method + + IN: phandle, [string] method + OUT: missing-flag? + Tests whether the package method named method exists in the package + phandle. missing-flag? is FALSE (0) if the method exists or TRUE (-1) if + the method does not exist. + + + + + OF may provide the following Client Interface Service: + + + + ibm,enable-ci64 + + IN: none + OUT: none + After the successful invocation of this method, all Client + Interface calls will utilize 64 bit cell items in their argument arrays. + This does not affect how the device tree is presented, which will still + assume that a cell is 32 bit in the property values. The method returns + using the cell size in which it was called. This method exists only on + platforms that present the + “ibm,enable-ci64-capable” property in the + root node. + + + + +
+ +
+ +
+
+ Support Packages + + This section describes the LoPAR Binding specific requirements of OF + support packages. These support packages are + disk-label and + tape-label. For “network” and/or + obp-tftp extensions, refer to + . These packages support the + loading and executing of a client program. Another means of executing a + Client Program is provided when an OS ROM is a “bootable + device” (Refer to + , as an example). + +
+ “disk-label” Support Package + + The process of loading and executing a client program is described + in two stages. The first stage determines what partition and/or file (if + one exists) to read into memory. This is done by locating a partition and + a file within the partition (if the partition supports a file system + structure) from the boot device, usually by means of a name lookup within + a directory contained within a disk “partition”. The second + stage examines the front portion (header) of the image for + “well-known” program formats. When the format of the image + has been determined, the loading is completed in a manner determined by + that format. + The name of the partition (and, a file contained within the + partition) can be explicitly specified by the user via the + load or + boot command, or can be implicitly specified by the + value of the + “boot-device” + property of the + /options node. The partition and filename are the + ARGUMENTS portion of the final COMPONENT of the PATH_NAME, as described + in section 4.3.1 of + . + The syntax for explicit partition/filename specification is given + in section + below where partition + identifies the partition to be used and filename is the name of a file + within that partition. If partition is omitted, the default partition (as + determined by the partition format) is used. If filename is omitted, the + default filename (i.e., the filename component of the + boot-device path-name) is used. + +
+ Media Layout Format + This section describes the media layout formats of Client Program + Images that the disk-label support package for an LoPAR platform shall + support; an implementation + may support additional mechanisms, in an + implementation-specific manner. The + disk-label package for a platform shall + support at least four(4) media layout types: + + + + FAT (FAT12 and FAT16 File System) + + + + FDISK (Partitions 4, 5, 6, 0x41 and 0x96) + + + + ISO-9660 (9660 File System) + + + + UDF + + + + An LoPAR platform may choose to support the following media layout + formats for historic reasons: + + + + Mac OS (MAC Binary Image) + + + +
+ FDISK Partition Types + + The following FDISK partition types shall be supported: + + + + Partition Type 4: FAT 12 or FAT 16 File System + + + + Partition Type 5: Extended Chained Partitions + + + + Partition Type 6: Extended Partitions + + + + Partition Type 0x41: Single program image + + + + Partition Type 0x96: ISO 9660 File System + + + + Partition Type 0x??: UDF File System + + + + FDISK partition type 0 is a free partition. Partition type 0x82 is + reserved and should not be used by this architecture. +
+ +
+ +
+ Open Method Algorithm + + The + open method of the + disk-label support package shall implement a disk + partition recognition algorithm that supports at least the set of disk + formats that are supported by the following algorithm. The following + algorithm is intended to support raw (uninterpreted) disks, raw + partitions of disks beginning with an FDISK partition map, and files on + FAT, UDF and ISO-9660 file systems both within FDISK partitions and by + themselves on disks without a partition map. + That + open method shall accept an argument string (as + returned by + “my-args”) with the following syntax + (according to the algorithm below), where brackets denote an optional + component: + [partition][,[filename]] + If the argument string contains a comma, or if the argument string + begins with a decimal digit, the partition component is deemed to be + present. Note that the arguments above are not the client arguments with + the boot command. + If the partition component is present, it selects the desired + partition, where partition 0 refers to the entire disk, partition 1 + refers to the first partition, partition 2 to the second, and so forth. + If the partition component is absent and the disk has an FDISK or Mac + partition map, the first “bootable” partition is used. If a + “bootable” partition is not found, then fail in an + implementation specific manner with an error. + If the filename component is present, it selects a particular file + within the file system on the disk or partition thereof. + + Note: For historic reasons, the following algorithm + includes support for the optional MAC OS media layout format. + + + PARTITION$, FILENAME$ +2 Else +3 Set PARTITION$ to the NULL string +3 Set FILENAME$ to ARGUMENT$ +2 If PARTITION$ is not the NULL string +3 If PARTITION$ is not a decimal number +4 Return FALSE +3 DECIMAL_STRING_TO_NUMBER (PARTITION$) -> PARTITION +3 If PARTITION is 0 +4 GET_DISK_SIZE +3 Else +4 Read the first 512 bytes of the device into a buffer +4 SELECT_EXPLICIT_PARTITION (PARTITION) +4 If SELECT_EXPLICIT_PARTITION returned an error indication +5 Return FALSE +2 Else \ PARTITION$ is NULL +3 Read the first 512 bytes of the device into a buffer +3 SELECT_ACTIVE_PARTITION +3 If SELECT_ACTIVE_PARTITION returned an error indication +4 Return FALSE +2 \ (At this point, D.OFFSET is set to the beginning of the selected + partition and D.SIZE is set to the size of that partition. If the + entire disk was selected, D.OFFSET is 0 and D.SIZE is the size of the disk.) +2 Call parent’s “seek” method with an argument of 0,0. +2 Return TRUE +1 CHECK_FOR_BPB procedure +2 If the first four(4) bytes are EBCDIC 'IBMA'(hex character string + C9C2D4C1), then the sector does not contain a BPB. +2 If the 16-bit little-endian quantity beginning at buffer offset 510 + is 0xAA55, and the 16-bit little-endian quantity beginning at buffer + offset 11 (which is the BPB “bytes per sector” field) is either 256, + 512, or 1024, and the byte at offset 16 (the BPB “number of FATs” field + is either 1 or 2, the sector is deemed to contain a BPB. Otherwise, the + sector does not contain a BPB. +1 CHECK_FOR_ISO_9660 procedure +2 Read 512-byte sector 64 (the beginning of logical 2048-byte sector 16)into + a buffer. +2 If the byte at offset 0 contains the binary number “1”, and the 5 bytes + beginning at offset 1 contains the text string “CD001”, the partition + or raw disk is deemed to contain an ISO 9660 file system. Otherwise, + the partition or raw disk is deemed not to contain an ISO 9660 file system. +1 CHECK_FOR_FDISK procedure +2 If the buffer does not contain an FDisk partition map signature of “AA55” + as a 16-bit little-endian number beginning at buffer offset 510, the buffer + is deemed not to contain an FDISK partition map. +2 If none of the partition type code field (the bytes at buffer offsets 0x1C2, + 0x1D2, 0x1E2, and 0x1F2) contains a recognizable partition type code (4,5, + 6, 0x41, 0x96, or other types that may be recognized by the implementation), + the buffer is deemed not to contain an FDISK partition map. +2 Otherwise, the buffer is deemed to contain an FDISK partition map. +2 The implementation may, at its option, apply additional validity tests to + the partition map information. +1 CHECK_FOR_MAC_DISK procedure +2 If the first (i.e., at the lowest offset) two bytes in the buffer contains + the 16-bit big-endian signature 0x4552, then the disk is deemed to be a Mac + partitioned disk. Otherwise, the partition or raw disk is deemed not to be + a Mac partitioned disk.]]> + + + Note: Subsequent 512 byte sectors will contain Mac + partition map entries, each of which begins with the 16-bit big-endian + signature 0x504D. Each such partition map entry contains a field (V) + indicating the total number of partition entries in the map. + + 1 +4 Return ERROR +2 CHECK_FOR_FDISK +2 If an FDisk partition map is found +3 Search the FDisk partition map beginning in 512-byte sector 0, reading new + 512-byte sectors into the buffer if necessary to “chain” to extended + partition entries, for the Nth, where N is the value of PARTITION, partition + entry whose “type” byte is neither 0 nor 5 (5 is the type code that + indicates a “chained” extended partition entry). +3 If the Nth partition is found: +4 Set PARTITION-TYPE to that entry's “type” field (the byte at offset 4) +4 Set D.OFFSET to the byte offset from the beginning of the disk to the + beginning of the partition denoted by that entry. +4 Set D.SIZE to the size of the partition in bytes denoted by that entry. +4 INTERPOSE_BY_TYPE +4 Return OKAY +3 Else \Nth partition does not exist +4 Return ERROR +2 CHECK_FOR_MAC_DISK +2 If this is a Mac partitioned disk +3 Search the Mac partition map for the Nth partition, where N is the value of + PARTITION. +3 If the Nth partition is valid, allocated, and readable +4 If FILENAME$ is %BOOT +5 If the Nth partition is marked bootable +6 Set D.OFFSET to the byte offset from the beginning of the disk + to the beginning of the boot area, as given by the pmLgBootStart + field. +6 Set D.SIZE to the size of the partition in bytes denoted by + pmBootSize. +6 Return OKAY +5 Else \Nth partition not “bootable” +6 Return ERROR +4 Else +5 If FILENAME$ is not the NULL string +6 INTERPOSE_BY_TYPE +5 Return OKAY +3 Else \ (If this point is reached, the partition is invalid) +4 Return ERROR +2 Else \ (If this point is reached, the partition map is not recognized) +3 Return ERROR]]> + + + This algorithm can be used to locate the correct partition and/or + file and/or load image from the specified device. The boot device is + selected as described in 7.4.3.2 of + . A filename can be explicitly + given as the arguments field of the + device-specifier (i.e., the field following the ':' + of the last path component). Other formats + may be recognized in an implementation-specific + manner. + +
+ +
+ +
+ tape-label Support Package + + The + tape-label Support Package shall + support tape as a standard byte device with the set + of methods specified in + , Section 3.7.3. Presence of + the bootinfo.txt file is optional. + The + open method shall accept an argument string, where + brackets denote an optional component: + [file number] + where the first file on the tape media is located at file number + 0. + +
+ Tape Format + + The LoPAR tape format shall consist of files ending with a file + mark (FM). The first block of data will be identified as file 0. The + bootinfo.txt file, if present, shall be located on the tape as file 0 + (the first file). There shall be only one bootinfo.txt file on the tape + media. Refer to + for the LoPAR Tape + format. + +
+ Tape Boot Format + + + + + + + + +
+ +
+ +
+ Tape bootinfo.txt File + The bootinfo.txt file shall have included for each set + of <chrp-boot> tags a set of <boot-script> tags that contains + a pointer to the program image to be loaded (Refer to + ). The form for this tape + pointer will be: + device specifier = device:file number + EXAMPLE: device specifier = tape:2 (For the specified set of + <chrp-boot> tags, load the tape program image from file 2). + A bootinfo.txt file may contain a multiple set of <chrp-boot> + tags where each one can point to a different tape file number. If a + bootinfo.txt file is not present, file 0 should be a bootable file. Only + file 0 will be loaded as a bootable image. No other files will be + searched if a bootinfo.txt file is not present unless the file number to + load is specified by an argument. + +
+ +
+ +
+ network Support Package + + The + network Support Package shall adhere to the + documentation functions and + conventions. + +
+ +
+ Program-image formats. + + OF must recognize a client program that is formatted as ELF, as + defined in + , and PE, as defined in + . Other formats + may be handled in an implementation-specific manner. + defines the FCode and Forth + Program-Image Formats. + After locating the file, OF reads the image into memory at the + location specified by the load-base Configuration Variable. Then, OF must + perform the following procedure to prepare the image for + execution. + + ”) + setup system to evaluate Forth Source Image +else if the image is a bootinfo.txt file (i.e., begins with “”) + setup system to parse the bootinfo.txt file +else + FAIL, in an implementation-specific manner.]]> + Notes: The following comments apply to the above code: + + + For more information on detecting an ELF format, refer to + . + + + + For more information on relocating an ELF image, refer to + . + + + +
+ +
+ + diff --git a/DeviceTree/ch_devtree_terms.xml b/DeviceTree/ch_devtree_terms.xml new file mode 100644 index 0000000..4979d94 --- /dev/null +++ b/DeviceTree/ch_devtree_terms.xml @@ -0,0 +1,330 @@ + + + + + Terms + + This standard uses technical terms as they are defined in the + IEEE Std 1275-1994 Standard and other + documents cited in “References”, plus the following + terms: + + + + ARP + + Address Resolution Protocol + + + + + BOOTP + + Bootstrap Protocol + + + + + CHRP + + Common Hardware Reference Platform + + + + + core, core specification, core document + + Refers to IEEE Std 1275-1994 Standard for Boot (Initialization, + Configuration) Firmware, Core Practices and Requirements + + + + + core errata + + Refers to Core Errata, IEEE P1275.7 + + + + + CPU + + Central Processing Unit + + + + + effective address + + The 64- or 32-bit address computed by the processor + when executing a Storage Access or Branch instruction, or when fetching the + next sequential instruction. If address translation is disabled, the real + address is the same as the effective address. If address translation is + enabled, the real address is determined by, but not necessarily identical + to, the effective address. + + + + + ELF Executable and Linking Format + + A binary object file format defined by + that is used to represent client + programs in OF for PA. + + + + + FDISK + + Refers to the boot-record and partition table format used by + MS-DOS, as defined in + . + + + + + gateway + + Network connecting device + + + + + host + + A computer. In particular a source or destination of messages + from the point of view of the communication network. + + + + + ICMP + + Internet Control Message Protocol + + + + + IETF + + Internet Engineering Task Force + + + + + IP + + Internet Protocol + + + + + IO + + Input/Output + + + + + LAN + + Local Area Network + + + + + linkage area + + An area within the stack that is reserved for saving + certain registers across procedure calls in PA run-time models. This area + is reserved by the caller and is allocated above the current stack pointer + (%r1). + + + + + NVRAM + + Non-volatile memory that is the repository for various + platform, OF and OS information that remains persistent across reboots, + power management activities and/or cycles. + + + + + Open Firmware (OF) + + The firmware architecture defined by + and + , or, when used as an adjective, + a software component compliant with the core specification and + errata. + + + + + PCU + + Power Configuration Utility; Refers to a platform program to + assist a user to manage device power. + + + + + PE + + Portable Executable. A binary object file format defined by + . + + + + + procedure descriptor + + A data structure used by some PA run-time models + to represent a C “pointer to procedure”. The first word of this + structure contains the actual address of the procedure. + + + + + processor bus + + The bus that connects the CPU chip to the system. + + + + + PROM + + Programmable Read Only Memory + + + + + real address + + An address that the processor presents on the processor + bus. + + + + + real-mode + + The mode in which OF and its client are running with + translation disabled; all addresses passed between the client and OF are + real (i.e., hardware) addresses. + + + + + RFC + + Internet Request For Comments; part of the technical process of + establishing a standard. + + + + + ROM + + Read Only Memory + + + + + segmented address translation + + The process whereby an Effective Address (EA) is translated into a + Virtual Address (VA) and the virtual address is translated into a Real + Address (RA). (see + and Book III of + for more detail.) + + + + + suspend + + A form of Power Management characterized by a fast recovery + to full operation. Typically, system memory will not be powered off while + in the suspend state. + + + + + Table of Contents (TOC) + + A data structure used by some PA run-time models that is used for + access to global variables and for inter-module linkage. When a TOC is + used, + %r2 contains its base address. + + + + + TFTP + + Trivial File Transfer Protocol + + + + + UDP + + User Datagram Protocol + + + + + Virtual Address + + In IEEE 1275 parlance, the address that a program uses to access + a memory location or + memory-mapped device register. Depending on the presence or absence of + memory mapping hardware in the system, and whether or not that mapping + hardware is enabled, a virtual address may or may not be the same as the + physical (real) address that appears on an external bus. The IEEE 1275 + definition of “virtual address” corresponds to The PA's + definition of “effective address.” Except as noted, this + document uses the IEEE 1275 definition of virtual address. + + In PA parlance, an internal address within the PA address + translation mechanism, used + as in intermediate term in the translation of an effective address to the + corresponding real address. + + + + + virtual-mode + + The mode in which OF and its client share a single + virtual address space, and address translation is enabled; all addresses + passed between the client and OF are virtual (translated) addresses. + + + + + diff --git a/DeviceTree/ch_introduction.xml b/DeviceTree/ch_introduction.xml new file mode 100644 index 0000000..a3e2417 --- /dev/null +++ b/DeviceTree/ch_introduction.xml @@ -0,0 +1,97 @@ + + + + + Introduction + + This document specifies the application of OF to an LoPAR System, + including requirements and practices to support unique hardware and + firmware specific to the platform implementation. The core requirements and + practices specified by OF must be augmented by system-specific requirements + to form a complete specification for the firmware implementation of an + LoPAR System. This appendix establishes such additional requirements + pertaining to the platform and the support required by OF. + + This document also specifies the application of OF to a PA Processor + (which covers all PowerPC processors and their successors), including + requirements and practices to support unique firmware specific to a PA + Processor. The core requirements and practices specified by OF must be + augmented by processor-specific requirements to form a complete + specification for the firmware implementation for a PA processor. + + establishes such additional requirements pertaining to the + processor and the support required by OF. + + This document further specifies the application of + IEEE Std 1275-1994 Standard for Boot (Initialization, + Configuration) Firmware, Core Practices and Requirements, + Core Errata, IEEE P1275.7 and appropriate OF Standards + for LoPAR computer systems, including practices for client program + interface and data formats. + +
+ General Requirements + An OF implementation for an LoPAR platform shall implement the + core requirements as defined in + , core errata + , the PA Processor-specific + extensions described in + , other appropriate bindings + and/or recommended practices contained in the references (see + ), and the LoPAR Binding + specific extensions described in this appendix. + In addition, an OF implementation for an LoPAR platform shall + implement the + Device Interface, + Client Interface and + User Interface as defined in + . + Some LoPAR Binding property names exceed the OF Base specification + limit of 31 characters. LoPAR OF implementations shall support property + names of at least 47 characters. + +
+ +
+ Processor Architecture Requirements + + specifies the application of + + + to computer systems that use the PA instruction set, including + instruction-set-specific requirements and practices for debugging, client + program interface and data formats. An implementation of OF for PA shall + implement the core requirements as defined in + and the PA-specific extensions + described in this binding. + This appendix addresses + . The descriptions that follow, + and the relevant sections describing translation features for this binding, + assume that the system’s PA processor(s) implement the entire PA + (that is, all books of + ). Some processors may implement + different Book II-III features; such processors may need a variant of this + binding describing the differences to the mapping functions, etc. + +
+ + diff --git a/DeviceTree/figures/PAPR-60.gif b/DeviceTree/figures/PAPR-60.gif new file mode 100644 index 0000000..48d379d Binary files /dev/null and b/DeviceTree/figures/PAPR-60.gif differ diff --git a/DeviceTree/figures/PAPR-61.gif b/DeviceTree/figures/PAPR-61.gif new file mode 100644 index 0000000..a7c8d89 Binary files /dev/null and b/DeviceTree/figures/PAPR-61.gif differ diff --git a/DeviceTree/figures/PAPR-62.gif b/DeviceTree/figures/PAPR-62.gif new file mode 100644 index 0000000..82eb58e Binary files /dev/null and b/DeviceTree/figures/PAPR-62.gif differ diff --git a/DeviceTree/figures/PAPR-64.gif b/DeviceTree/figures/PAPR-64.gif new file mode 100644 index 0000000..bd2ffa3 Binary files /dev/null and b/DeviceTree/figures/PAPR-64.gif differ diff --git a/DeviceTree/pom.xml b/DeviceTree/pom.xml new file mode 100644 index 0000000..66148fd --- /dev/null +++ b/DeviceTree/pom.xml @@ -0,0 +1,148 @@ + + + + + org.openpowerfoundation.docs + workgroup-pom + 1.0.0-SNAPSHOT + ../pom.xml + + 4.0.0 + + + LoPAR-DeviceTree + + jar + + + LoPAR-DeviceTree + + + + + 0 + + + + + + + + + org.openpowerfoundation.docs + + openpowerdocs-maven-plugin + + + + generate-webhelp + + generate-webhelp + + generate-sources + + + ${comments.enabled} + LoPAR-DeviceTree + 1 + UA-17511903-1 + + appendix toc,title + article/appendix nop + article toc,title + book toc,title,figure,table,example,equation + book/appendix nop + book/chapter nop + chapter toc,title + chapter/section nop + section toc + part toc,title + qandadiv toc + qandaset toc + reference toc,title + set toc,title + + + 1 + 3 + 1 + + + LoPAR_DeviceTree + + + LoPAR_DeviceTree + + + + workgroupSpecification + + + + + workgroupConfidential + + + + + draft + + + + + + + + + true + . + + + bk_main.xml + + + + + ${basedir}/../glossary/glossary-terms.xml + 1 + www.openpowerfoundation.org + + + + + + diff --git a/Error Handling/app_bibliography.xml b/Error Handling/app_bibliography.xml new file mode 100644 index 0000000..4b48169 --- /dev/null +++ b/Error Handling/app_bibliography.xml @@ -0,0 +1,284 @@ + + + + + Bibliography + This section lists documents which were referenced in this specification or which provide + additional information, and some useful information for obtaining these documents. Referenced + documents are listed below. When any of the following standards are superseded by an approved + revision, the revision shall apply. + + + + + + Linux on Power Architecture Reference: Platform and Device Tree + + + + + Linux on Power Architecture Reference: Device Tree + + + + + + + Linux on Power Architecture Reference: Virtualization + + + + + Linux on Power Architecture Reference: Runtime Abstraction Services (RTAS) + + + + + Power ISA + + + + + IEEE 1275, IEEE Standard for Boot (Initialization Configuration) Firmware: + Core Requirements and Practices + IEEE part number DS02683, ISBN 1-55937-426-8 + + + + + Core Errata, IEEE P1275.7/D4 + + + + + Open Firmware Recommended Practice:OBP-TFTP + Extension + + + + + Open Firmware Recommended Practice: Device + Support Extensions + + + + + PCI Bus binding to: IEEE Std 1275-1994, Standard + for Boot (Initialization, Configuration) Firmware + + + + + Open Firmware: Recommended Practice - Interrupt + Mapping + + + + + Open Firmware: Recommended Practice - Forth Source + and FCode Image Support, Version 1.0 + + + + + Open Firmware: Recommended Practice - Interrupt + Mapping, Version 1.0 + + + + + Open Firmware: Recommended Practice - TFTP Booting + Extensions, Version 0.8 + + + + + Open Firmware: Recommended Practice - + Interposition, Version 0.2 + + + + + MS-DOS Programmer's Reference + Published by Microsoft + + + + + Peering Inside the PE: A Tour of the Win32 Portable + Executable File Format + Found in the March, 1994 issue of Microsoft Systems Journal + + + + + ISO-9660, Information processing -- Volume and + file structure of CD-ROM for information interchange + Published by International Organization for Standardization + + + + + System V Application Binary Interface, PowerPC + Processor Supplement + By Sunsoft + + + + + ISO Standard 8879:1986, Information Processing + -- Text and Office Systems -- Standard Generalized Markup Language (SGML) + + + + + IEEE 996, A Standard for an Extended Personal Computer + Back Plane Bus + + + + + PCI Local Bus Specification + All designers are responsible for assuring that they use the most current version of this document + at the time that they design conventional PCI related components or platforms. See the PCI SIG website + for the most current version of this document. + + + + + PCI-to-PCI Bridge Architecture Specification + All designers are responsible for assuring that they use the most current version of this document + at the time that they design conventional PCI related components or platforms. See the + PCI SIG website for the most current version of this document. + + + + + PCI Standard Hot-Plug Controller and Subsystem + Specification + + + + + PCI-X Protocol Addendum to the PCI Local Bus Specification + All designers are responsible for assuring that they use the most current version of this document at + the time that they design PCI-X related components or platforms. See the PCI SIG website for the most + current version of this document. + + + + + PCI Express Base Specification + All designers are responsible for assuring that they use the most current version of this document + at the time that they design PCI Express related components or platforms. See the PCI SIG website for + the most current version of this document. + + + + + PCI Express to PCI/PCI-X Bridge Specification + All designers are responsible for assuring that they use the most current version of this document at the + time that they design PCI Express related components or platforms. See the PCI SIG website for the most current + version of this document. + + + + + System Management BIOS (SMBIOS) Reference + Specification + + + + + (List Number Reserved for Compatibility) + + + + (List Number Reserved for Compatibility) + + + + (List Number Reserved for Compatibility) + + + + + IBM RS/6000® Division, Product Topology Data System, + Product Development Guide + Version 2.1 + + + + + Single Root I/O Virtualization and Sharing Specification + All designers are responsible for assuring that they use the most current version of this document at + the time that they design PCI Express SR-IOV related components or platforms. See the PCI SIG website + for the most current version of this document. + + + + + Multi-Root I/O Virtualization and Sharing Specification + All designers are responsible for assuring that they use the most current version of this document at the + time that they design PCI Express MR-IOV related components or platforms. See the PCI SIG website for the + most current version of this document. + + + + + + diff --git a/Error Handling/app_fault_v_errorlog.xml b/Error Handling/app_fault_v_errorlog.xml new file mode 100644 index 0000000..0b50f15 --- /dev/null +++ b/Error Handling/app_fault_v_errorlog.xml @@ -0,0 +1,891 @@ + + + + + When to use: Fault vs. Error Log Indicators (Lightpath Mode) + This appendix gives + highly recommended Service Indicator activation models + for typical system issues, when the Lightpath mode is implemented. The + purpose of this appendix is to get consistency across platforms, and to + answer common questions about how to handle specific issues. The reason that + these are recommended rather than required, is due to the range of systems + that are involved, specifically related to the different types of physical + layouts (for example: deskside, blade and blade chassis, rack-mounted and + particularly high end racks). + This appendix does + not change the architectural requirements specified in + other parts of this document, nor the requirement for implementations to + support those requirements. If there are any inconsistencies between this + appendix and the requirements in the rest of this document, the requirements + take precedence over this appendix. It is very important, therefore, that + designers understand the requirements in this architecture, and more + specifically, those in + . + gives the recommended models. The + general model, though, is still dictated by the following requirement, copied + here from the : + + + + + + + + + + + + + Service Indicator Activation Models for Typical System + Issues (Lightpath Mode) + <emphasis></emphasis> + + + + + + + + + + + + + Component or problem area + + + + + Problem or issue + + + + + Indicator activation? + (see notes + , + ) + + + + + Entry made in Service Focal Point error + log? + + + + + IBM Call Home? + + + + + Comments + + + + + + FRU Fault indicator?(see notes + , + ) + + + Error Log indicator?(see note + ) + + + + + + + All + + + Any not already covered in this table + + + Consult with the xipSIA architecture team for the proper + behavior + + +   + + + + + Power supply or fan + + + Redundant optional one missing + + + no + + + no + + + no + + + no + + + This row for information only (this is not a Serviceable + Event). + + + + + Redundant non-optional one missing + + + no + + + yes + + + yes + + + no + + +   + + + + + Failed redundant + + + yes + + + no + + + yes + + + yes + + +   + + + + + Failed non-redundant + + + yes + + + no + + + yes + + + yes + + +   + + + + + Power regulator not in power supply + + + Failed + + + yes + + + no + + + yes + + + yes + + + Treated the same as any other FRU or component on a FRU which + fails. + + + + + Power + + + Insufficient power with all power supplies installed and + operational for power domain + + + no + + + yes + + + yes + + + no + + + For components that will not power up due to lack of power + (for example, a blade in a chassis), and when that component + implements a fast blink capability for the green power LED, that + component’s green power LED remains in the fast blink + mode. + + + + + Insufficient power with missing power supply + + + no + + + yes + + + yes + + + no + + + + + Disabled button pressed + + + Unable to power on or off component due to power button being + disabled + + + no + + + no + + + no + + + no + + + These rows for information only (these are not a Serviceable + Events). + + + + + KVM or media tray button pressed, but not active because + disabled + + + no + + + no + + + no + + + no + + + + + Temperature detected out of tolerance + + + Warning only (no performance throttling or shut-down) + + + no + + + no + + + brand dependent + + + no + + +   + + + + + Performance throttling or shut-down due to over-temp + condition + + + yes + + + no + + + yes + + + no + + + FRU Fault indicator must be at component that is throttled or + shut-down (temperature indicators, which are not architected, do + not roll-up to Enclosure Fault indicators). + + + + + Memory (DIMMs) + + + No memory installed at all, or memory that is installed is + mismatched + + + yes + + + no + + + yes + + + no + + +   + + + + + Invalid memory configuration above the base memory (missing + memory, mismatched memory, unsupported memory) + + + no + + + yes + + + yes + + + no + + +   + + + + + Failed or predicted to fail + + + yes + + + no + + + yes + + + yes + + +   + + + + + System VPD + + + Invalid or missing + + + yes + + + no + + + yes + + + yes + + + Lack of some of the required fields in the call-home may + result in the call-home being flagged as a lack of + entitlement. + + + + + Battery + + + Missing or failed + + + yes + + + no + + + yes + + + brand dependent + + +   + + + + + Rechargeable battery needing reconditioning + + + no + + + yes + + + yes + + + no + + +   + + + + + CPU + + + Failed or predicted to fail + + + yes + + + no + + + yes + + + yes + + +   + + + + + Planar or CEC + + + Failed + + + yes + + + no + + + yes + + + yes + + +   + + + + + Disk + + + Failed or predicted to fail + + + yes + + + no + + + yes + + + yes + + +   + + + + + Boot device + + + Missing boot device + + + no + + + yes + + + yes + + + no + + +   + + + + + Corrupt image + + + no + + + yes + + + yes + + + no + + +   + + + + + I/O adapter + + + Fail or non-recoverable EEH error + + + yes + + + no + + + yes + + + yes + + +   + + + + + Service Processor (FSP, BMC, IMM) + + + Hardware failure + + + no + + + yes + + + yes + + + yes + + +   + + + + + Firmware failure + + + no + + + yes + + + yes + + + brand dependent + + +   + + + + + BIOS or Flash + + + Corrupted single side + + + no + + + yes + + + yes + + + no + + +   + + + + + Both sides corrupted + + + yes + + + no + + + yes + + + yes + + +   + + + + + All + + + Unisolated event + + + no + + + yes + + + yes + + + no + + + See also Requirement + + + + + + Switch + + + Failed + + + yes + + + no + + + yes + + + yes + + +   + + + + + System chassis controller (AMM, CME, ITME) + + + Failed + + + yes + + + no + + + yes + + + yes + + +   + + + + + Midplane + + + Failed + + + yes + + + no + + + yes + + + yes + + +   + + + + + Cables + + + Failed or missing + + + N/A + + + yes + + + yes + + + yes + + +   + + + + +
+ + Notes: + + + + + Never activate both a + Fault indicator and an Error Log indicator for the same problem. See also + Requirement + , referenced immediately above + . + + + + Fault indicators + above the FRU Fault indicator are not specified here, but the requirements + specify that a FRU Fault is rolled-up to the next higher level indicator + (specifically, the Enclosure Fault indicator). + + + + Enclosure Fault + indicators and above are only roll-up indicators and are never activated + without a FRU Fault indicator being activated. Therefore the column in + indicates a FRU Fault indicator. + That is, if no FRU Fault indicator exists for the problem, then the Error Log + indicator is used instead (per Requirement + , referenced immediately above + ). + + + + The activation of the + Error Log indicator (previously known as the System Information (Attention) + indicator) and Fault indicators are regulated by the following requirements, + among others: + + + + + + + + + diff --git a/Error Handling/app_glossary.xml b/Error Handling/app_glossary.xml new file mode 100644 index 0000000..3aae9ef --- /dev/null +++ b/Error Handling/app_glossary.xml @@ -0,0 +1,1290 @@ + + + + + Glossary + This glossary contains an alphabetical list of terms, phrases, and abbreviations used in this document. + + + + Term + Definition + + + + AC + Alternating current + + + + ACR + Architecture Change Request + + + + AD + Address Data line + + + + Adapter + A device which attaches a device to a bus or which converts one + bus to another; for example, an I/O Adapter (IOA), a PCI Host Bridge (PHB), + or a NUMA fabric attachment device. + + + + + addr + Address + + + + Architecture + The hardware/software interface definition or software module to + software module interface definition. + + + + ASCII + American National Standards Code for Information + Interchange + + + + ASR + Address Space Register + + + + BAT + Block Address Translation + + + + BE + Big-Endian or Branch Trace Enable bit in the + MSR (MSRBE) + + + + BIO + Bottom of Peripheral Input/Output Space + + + + BIOS + Basic Input/Output system + + + + BIST + Built in Self Test + + + + Boundedly undefined + Describes some addresses and registers which when referenced provide + one of a small set of predefined results. + + + + BPA + Bulk Power Assembly. Refers to components used for power distribution + from a central point in the rack. + + + + BPM + Bottom of Peripheral Memory + + + + BSCA + Bottom of System Control Area + + + + BSM + Bottom of System Memory + + + + BUID + Bus Unit Identifier. The high-order part of an interrupt source number + which is used for hardware routing purposes by the platform. + + + + CCIN + Custom Card Identification Number + + + + CD-ROM + Compact Disk Read-Only Memory + + + + CIS + Client Interface Service + + + + CMO + Cooperative Memory Over-commitment option. See + for more information. + + + + + + CMOS + Complimentary Metal Oxide Semiconductor + + + + Conventional PCI + Behavior or features that conform to . + + + + CPU + Central Processing Unit + + + + CR + Condition Register + + + + CTR + Count Register + + + + DABR + Data Address Breakpoint Register + + + + DAR + Data Address Register + + + + DASD + Direct Access Storage Device (a synonym for “hard disk”) + + + + DBAT + Data Block Address Translation + + + + DC + Direct current + + + + DEC + Decrementer + + + + DIMM + Dual In-line Memory Module + + + + DMA + Direct Memory Access + + + + DMA Read + A data transfer from System Memory to I/O. A DMA Read Request + is the inbound operation and the DMA Read Reply (or Read Completion) is the + outbound data coming back from a DMA Read Request. + + + + DMA Write + A data transfer to System Memory from I/O or a Message Signalled Interrupt (MSI) DMA Write. This is an inbound operation. + + + + DOS + Disk OS + + + + DR + Data Relocate bit in MSR (MSRDR) + + + + DRA + Deviation Risk Assessment + + + + DRAM + Dynamic Random Access Memory + + + + DRC + Delayed Read Completion. A transaction that has completed + on the destination bus and is now moving toward the originating bus to complete. + DR Connector. + + + + DR entity + An entity that can participate in DR operations. That is, an entity + that can be added or removed from the platform while the platform power is on and the + system remains operational. + + + + DRR + Delayed Read Request. A transaction that must complete on the destination bus before completing on the originating bus. + + + + DSISR + Data Storage Interrupt Status Register + + + + DWR + Delayed Write Request. A transaction that must complete on the destination bus before completing on the originating bus. + + + + EA + Effective Address + + + + EAR + External Access Register + + + + ECC + Error Checking and Correction + + + + EE + External interrupt Enable bit in the MSR (MSREE) + + + + EEH + Enhance I/O Error Handling + + + + EEPROM + Electrically Erasable Programmable Read Only Memory + + + + EPOW + Environment and Power Warning + + + + + Error Log indicator An amber indicator that indicates that the user needs to + look at the error log or problem determination procedures, in order to determine the cause. + Previously called System Information (Attention). + + + + FCode + A computer programming language defined by the OF standard which is semantically + similar to the Forth programming language, but is encoded as a sequence of binary byte codes + representing a defined set of Forth words. + + + + FE0 + Floating-point Exception mode 0 bit in the MSR (MSRFE0) + + + + FE1 + Floating-point Exception mode 1bit in the MSR (MSRFE1) + + + + FIR + Fault Isolation Registers + + + + FLR + Function Level Reset (see PCI Express documentation). An optional reset for PCI Express + functions that allows resetting a single function of a multi-function IOA. + + + + FP + Floating-Point available bit in the MSR (MSRFP) + + + + FPSCR + Floating-Point Status And Control Register + + + + FRU + Field Replaceable Unit + + + + FSM + Finite State Machine + + + + GB + Gigabytes - as used in this document it is 2 raised to the power of 30 + + + + HB + Host Bridge + + + + HMC + Hardware Management Console - used generically to refer to the system + component that performs platform administration function where ever physically located. + The HMC is outside of this architecture and may be implemented in multiple ways. + Examples include: a special HMC applications in another system, an external appliance, + or in an LPAR partition using the Virtual Management Channel (VMC) interface to the + hypervisor. + + + + Hz + Hertz + + + + IBAT + Instruction block address translation + + + + ID + Identification + + + + IDE + Integrated Device Electronics + + + + IDU + Interrupt Delivery Unit + + + + IEEE + Institute of Electrical and Electronics Engineers + + + + I2C + Inter Integrated-circuit Communications + + + + I/O + nput/Output + + + + I/O bus master + Any entity other than a processor, cache, + memory controller, or host bridge which supplies both address and data in + write transactions or supplies the address and is the sink for the data in + read transactions. + + + + I/O device + Generally refers to any entity that is connected + to an IOA (usually through a cable), but in some cases may refer to the IOA + itself (that is, a device in the device tree that happens to be used for I/O + operations). + + + + I/O Drawer + An enclosure in a rack that holds at least one PHB and at + least one IOA. + + + + ILE + Interrupt Little-Endian bit in MSR (MSRILE) + + + + Instr + Instruction + + + + Interrupt Number + See Interrupt Vector below. + + + + Interrupt Vector + The identifier associated with a specific interrupt source. + The identifier’s value is loaded into the source’s Interrupt Vector Register and + is read from the Interrupt Delivery Unit’s Interrupt Acknowledge Register. + + + + IOA + I/O Adapter. A device which attaches to a physical bus which is capable + of supporting I/O (a physical IOA) or logical bus (a virtual IOA). The term “IOA” + without the usage of the qualifier “physical” or “virtual” will be + used to designate a physical IOA. Virtual IOAs are defined further in + + . + In PCI terms, an IOA may be defined by a unique combination of its assigned + bus number and device number, but not necessarily including its function number. + That is, an IOA may be a single or multi-function device, unless otherwise specified by + the context of the text. In the context of a PCIe I/O Virtualized (IOV) device (not to be + confused with a virtual IOA), an IOA is a single or multiple function device (for example, a + PCIe Virtual Function (VF) or multiple VFs). An IOA function may or may not have its own set of + resources, that is may or may not be in its own Partitionable Endpoint (PE) domain + (see also + + ). + + + + + IOA function + That part of an IOA that deals with a specific part of the + IOA as defined by the configuration space “Function” part of Bus/Device/Function. + For single-function IOAs, the IOA Function and the IOA are synonymous. + + + + IP + Interrupt Prefix bit in MSR (MSRIP) + + + + IPI + Interprocessor Interrupt + + + + IR + Instruction Relocate bit in MSR register (MSRIR) or infrared + + + + ISF + Interrupt 64-bit processor mode bit in the MSR (MSRISF) + + + + ISO + International Standards Organization + + + + ISR + Interrupt Source Register + + + + ISU + Interrupt Source Unit + + + + KB + Kilobytes - as used in this document it is 2 raised to the power of 10 + + + + KHz + Kilo Hertz + + + + LAN + Local Area Network + + + + LCD + Liquid Crystal Display + + + + LE + Little-Endian bit in MSR (MSRLE) or Little-Endian + + + + LED + Light Emitting Diode + + + + LMB + Logical Memory Block. The Block of logical memory addresses associated with a dynamically + reconfigurable memory node. + + + + Load + A Load Request is the outbound (from the processor) operation + and the Load Reply is the inbound data coming back from a + Load Request. When it relates to I/O operations, this is an + MMIO Load . + + + + LR + Link Register + + + + LSb + Least Significant bit + + + + LSB + Least Significant Byte + + + + LSI + Level Sensitive Interrupt + + + + LUN + Logical Unit Number + + + + L1 + Primary cache + + + + L2 + Secondary cache + + + + MB + Megabytes - as used in this document it is 2 raised to the power of 20 + + + + ME + Machine check Enable + + + + MMIO + Memory Mapped I/O. This refers to the mapping of the address space required + by an I/O device for Load or Store operations into + the system’s address space. + + + + MES + Miscellaneous Equipment Specification + + + + MFM + Modified frequency modulation + + + + MHz + Mega Hertz + + + + MOD + Address modification bit in the MSR + (MSRMOD) + + + + MP + Multiprocessor + + + + MSb + Most Significant bit + + + + MSB + Most Significant Byte + + + + MSI + Message Signalled Interrupt + + + + MSR + Machine State Register + + + + MTT + Multi-TCE-Table option. See + + + . + + + + + N/A + Not Applicable + + + + Nibble + Refers to the first or last four bits in an 8 bit byte + + + + NUMA + Non-Uniform Memory Access + + + + NUMA fabric + Mechanism and method for connecting the multiple nodes of a NUMA system + + + + NVRAM + Nonvolatile Random Access Memory + + + + OF + Open Firmware + + + + OP + Operator + + + + OS + Operating System + + + + OUI + Organizationally Unique Identifier + + + + PA + Processor Architecture + + + + PAP + Privileged Access Password + + + + LoPAR + Used within the Linux on Power Architecture + Reference documents to denote: (1) the architectural requirements specified + by the Linux on Power Architecture Reference document, (2) the Linux on Power Architecture + Reference documents themself, and (3) as an adjective to qualify an entity as being + related to this architecture. + + + + Partitionable Endpoint + This refers to the I/O granule that may be treated as one for + purposes of assignment to an OS (for example, to an LPAR partition). May be an + I/O adapter (IOA), or groups of IOAs and bridges, or portions of IOAs. PE granularity + supported by the hardware may be finer than is supported by the firmware. Grouping + of multiple PEs into one DR entity may limit assignment of a the separate PEs to different + LPAR partitions. See also DR entity. + + + + PC + Personal Computer + + + + PCI + Peripheral Component Interconnect. An all-encompassing term referring to + conventional PCI, PCI-X, and PCI Express. + + + + PCI bus + A general term referring to either the PCI Local Bus, as + specified in and + for conventional PCI and PCI-X, or a PCI Express link, as specified in + for PCI Express. + + + + PCI Express + Behavior or features that conform to + . + + + + PCI link + A PCI Express link, as specified in . + + + + PCI-X + Behavior or features that conform to . + + + + PD + Presence Detect + + + + PE + When referring to the body of the LoPAR, this refers to a Partitionable + Endpoint. + + + + + + + PEM + Partition Energy Management option. See + + + . + + + + + Peripheral I/O Space + The range of real addresses which are assigned + to the I/O Space of a Host Bridge (HB) and which are sufficient to contain all of + the Load and Store address space requirements of all the devices in the I/O Space + of the I/O bus that is generated by the HB. A keyboard controller is an example of + a device which may require Peripheral I/O Space addresses. + + + + Peripheral Memory Space + The range of real addresses which are assigned to the Memory + Space of a Host Bridge (HB) and which are sufficient to contain all of the Load and + Store address space requirements of the devices in the Memory Space of the I/O bus + that is generated by the HB. The frame buffer of a graphics adapter is an example + of a device which may require Peripheral Memory Space addresses. + + + + Peripheral Space + Refers to the physical address space which may + be accessed by a processor, but which is controlled by a host bridge. At least one + peripheral space must be present and it is referred to by the suffix 0. A host bridge + will typically provide access to at least a memory space and possibly to an I/O + space. + + + + PHB + PCI Host Bridge + + + + PIC + Programmable Interrupt Controller + + + + PIR + Processor Identification Register + + + + Platform + Refers to the hardware plus firmware portion of a system composed of hardware, + firmware, and OS. + + + + Platform firmware + Refers to all firmware on a system including the software or firmware in a + support processor. + + + + Plug-in I/O card + A card which can be plugged into an I/O + connector in a platform and which contains one or more IOAs and potentially + one or more I/O bridges or switches. + + + + Plug-in Card + An entity that plugs into a physical slot. + + + + PMW + Posted memory write. A transaction that has complete on the + originating bus before completing on the destination bus + + + + PnP + Plug and Play + + + + POP + Power On Password + + + + POST + Power-On Self Test + + + + PR + Privileged bit in the MSR (MSRPR) + + + + Processor Architecture + Used throughout this document to + mean compliance with the requirements specified in + . + + + + Processor revision number + A 16-bit number that distinguishes between various releases + of a particular processor version, for example different engineering change + levels. + + + + PVN + Processor Version Number. Uniquely determines the particular + processor and PA version. + + + + PVR + Processor Version Register. A register in each processor + that identifies its type. The contents of the PVR include the processor + version number and processor revision number. + + + + RAID + Redundant Array of Independent Disks + + + + RAM + Random Access Memory + + + + RAS + Reliability, Availability, and Serviceability + + + + Real address + A real address results from doing address + translation on an effective address when address translation is enabled. + If address translation is not enabled, the real address is the same as the + effective address. An attempt to fetch from, load from, or store to a real + address that is not physically present in the machine may result in a + machine check interrupt. + + + + Reserved + The term “reserved” is used within this + document to refer to bits in registers or areas in the address space + which should not be referenced by software except as described in this + document. + + + + Reserved for firmware use + Refers to a given location or bit which may not be used by + software, but are used by firmware. + + + + Reserved for future use + Refers to areas of address space or bits in registers which may be + used by future versions of this architecture. + + + + RI + Recoverable interrupt bit in the MSR (MSRRI) + + + + RISC + Reduced Instruction Set Computing + + + + RMA + Real Mode Area. The first block of logical memory addresses + owned by a logical partition, containing the storage that may be accessed with + translate off. + + + + ROM + Read Only Memory + + + + Root Complex + A PCI Express root complex as specified in + . + + + + RPN + Real Page Number + + + + RTAS + Run-Time Abstraction Services + + + + RTC + Real Time Clock + + + + SAE + Log Service Action Event log + + + + SCC + Serial Communications Controller + + + + SCSI + Small Computer System Interface + + + + SE + Single-step trace enabled bit in the MSR + (MSRSE) + + + + Service Focal Point + The common point of control in the system for handling all + service actions + + + + Serviceable Event + Serviceable Events are platform, + global, regional and local error events that require a service action + and possibly a call home when the serviceable event must be handled by a + service representative or at least reported to the service provider. + Activation of the Error Log indicator notifies the customer of the event + and the event indicates to the customer that there must be some intervention + to rectify the problem. The intervention may be a service action that the + customer can perform or it may require a service provider. + + + + SES + Storage Enclosure Services (can also mean SCSI Enclosure + Services in relation to SCSI storage) + + + + SF + Processor 32-bit or 64-bit processor mode bit in the MSR + (MSRSF) + + + + SFP + Service Focal Point + + + + Shrink-wrap OS + A single version of an OS that runs on all + compliant platforms. + + + + Shrink-wrap Application + A single version of an application program + that runs on all compliant platforms with the applicable OS. + + + + SMP + Symmetric multiprocessor + + + + SMS + System Management Services + + + + Snarf + An industry colloquialism for cache-to-cache + transfer. A typical scenario is as follows: (1) cache miss from cache A, + (2) line found modified in cache B, (3) cache B performs castout of modified + line, and (4) cache A allocates the modified line as it is being written back + to memory. + + + + Snoop + The act of interrogating a cache for the presence of a + line, usually in response to another party on a shared bus attempting to + allocate that line. + + + + SPRG + Special Purpose Registers for General use + + + + SR + System Registers + + + + SRC + Service Reference Code + + + + SRN + Service Request Number + + + + Store + A Store Request is an + outbound (from the processor) operation. When it relates to I/O + operations, this is an MMIO Store. + + + + System + Refers to the collection of hardware, system firmware, + and OS software which comprise a computer model. + + + + System address space + The total range of addressability as established by the + processor implementation. + + + + System Control Area + Refers to a range of addresses which + contains the system ROM(s) and an unarchitected, reserved, platform-dependent + area used by firmware and Run-Time Abstraction services for control of the + platform. The ROM areas are defined by the OF properties in the + openprom and os-rom nodes + of the OF device tree. + + + + System Information (Attention) indicator + See Error Log indicator. + + + + System firmware + Refers to the collection of all firmware on a system + including OF, RTAS and any legacy firmware. + + + + System Memory + Refers to those areas of memory which form + a coherency domain with respect to the PA processor or processors that + execute application software on a system. + + + + System software + Refers to the combination of OS software, + device driver software, and any hardware abstraction software, but + excludes the application software. + + + + TB + Time Base + + + + TCE + Translation Control Entry + + + + TLB + Translation Look-aside Buffer + + + + TOD + Time Of Day + + + + TOSM + Top of system memory + + + + TPM + Top of Peripheral Memory + Trusted Platform Module + + + + tty + Teletypewriter or ASCII character driven + terminal device + + + + UI + User Interface + + + + USB + Universal Serial Bus + + + + v + Volt + + + + VGA + Video Graphics Array + + + + VMC + Virtual Management Channel + + + + VPD + Vital Product Data + + + + VPNH + Virtual Processor Home Node option. See + + + . + + + + + + + + + + + + + + diff --git a/Error Handling/bk_main.xml b/Error Handling/bk_main.xml new file mode 100644 index 0000000..c5ab023 --- /dev/null +++ b/Error Handling/bk_main.xml @@ -0,0 +1,111 @@ + + + + + + + Error Handling + Linux on Power Architecture Reference + + + + + System Software Work Group + + syssw-chair@openpowerfoundation.org + + OpenPOWER Foundation + + + + 2016 + OpenPOWER Foundation + + + Revision 2.0_pre1 + OpenPOWER + + + + + + Copyright details are filled in by the template. + + + + + + The purpose of this document is to provide firmware and software + architectural details associated with Error Recovery and Logging on OpenPOWER Systems. + The base content for this document were contributed to the OpenPOWER Foundation in the + IBM Linux on Power Architecture Platform Reference (LoPAPR) Draft + document. It had numerous contributors inside IBM. + This document is a Standard Track, Work Group Specification work product owned by the + System Software Workgroup and handled in compliance with the requirements outlined in the + OpenPOWER Foundation Work Group (WG) Process document. It was + created using the Master Template Guide version 0.9.5. Comments, + questions, etc. can be submitted to the public mailing list for this document at + TBD. + + + + + + 2016-05-04 + + + + Revision 2.0_pre1 - initial conversion from IBM document. Extracted from + Linux on Power Architecture Platform Reference (LoPAPR) version 1.1 dated March 24, + 2016 -- Section 7.3.3 ([RTAS] Error and Event Reporting), Chapter 10 (Error and + Event Notification), Sections 1-3 of Chapter 16 (Service Indicators), and + Appendix L (When to use: Fault vs. Error Log Indicators). + + + + + + + + + + + + + + + + + + + + + + + + + + + + + diff --git a/Error Handling/ch_error_codes.xml b/Error Handling/ch_error_codes.xml new file mode 100644 index 0000000..ac42c69 --- /dev/null +++ b/Error Handling/ch_error_codes.xml @@ -0,0 +1,1280 @@ + + + + + Error Codes + +
+ Displaying Codes on the Standard Operator Panels + + + + + R1--1. + + Platform Implementation: Platforms must display + firmware progress codes (4 hex digits) on the operator panel display. On + 2x16 LCD displays, the progress codes are displayed left-justified on the + first line. + + + + + R1--2. + + Platform Implementation: Platforms must display + firmware error codes (8 hex digits) on the system console (graphic or + tty), and left-justified on the first line of a 2x16 LCD operator panel + display (if available). + + + + + R1--3. + + Platform Implementation: When a platform displays + firmware error codes, associated location codes must be displayed on the + following line on the system console (graphic or tty), and left-justified + on the second line of a 2x16 LCD operator panel display (if + available). + + + + + + The following describes in more detail the standard platform usage + of operator panel LEDs or LCDs for the display of firmware progress and + error codes. + + + + + Progress codes: Progress codes + from the system firmware and + service processor firmware are 4 hex digits in the range from 0x8000 + through 0xFFFF. Codes are displayed in the 4 character positions of a 1x4 + LED, or left justified in the first line of a 2x16 LCD. Subsequent + progress codes are displayed on top of (overlaying) the previous one. If + the system “hangs”, the last displayed progress code is left + on the display. + + + + + Error codes: Error codes are 8 + hex digits, as defined in + . These codes are displayed by + either boot ROM Power On Self Test (POST) or the service processor. If a + critical error is detected which prevents a successful boot or results in + system halt condition, the error code will be displayed left justified on + the first line of a 2x16 LCD. The error code is left on the LCD until the + system is reset or powered down. Error codes are not displayed on the + operator panel of platforms with only a 4-digit LED. On all platforms, + however, POST error codes are displayed on any system console (graphic or + tty). For non-critical errors where the system can boot and operate + normally or in a degraded mode, the associated error codes are not + displayed, but are reported to the OS via the POST error log and the RTAS + event-scan service. + + + + + Location Codes: Location codes + describe the physical location of + the most probable failing part associated with an error code. When an + error code is displayed on the first line of a 2x16 LCD, the location + code, if known, is displayed left justified on the second line. The + location code will remain on the LCD along with the error code until the + system is reset or powered down. Location codes for POST errors are also + displayed on any system console (graphic or tty), on the next line below + the error code. + + + + +
+ +
+ Firmware Error Codes + + The error code is an 8-character (4-byte) hexadecimal code produced + by firmware to identify the potential failing function or FRU in a + system. It consists of 5 source code characters and 3 reason code + characters. Individual characters within the error code have specific + field definitions, as defined in the following tables. + + + + + R1--1. + + Platform Implementation: To indicate the occurrence + of a critical platform error, platforms must display (either on an + operator panel or console) an 8-digit hex error code as defined in + and + . + + + + + + + + Service Reference Code (SRC) Field Layout + + + + + + + + + + + + + + + + Source Code + + + + + Reason Code + + + + + + + + + Byte 0 + + + + + Byte 1 + + + + + Byte 2 + + + + + Byte 3 + + + + + + S1 + + + S2 + + + S3 + + + S4 + + + S5 + + + R1 + + + R2 + + + R3 + + + + +
+ + + Service Reference Code (SRC) Field + Descriptions + + + + + + + + + + Field + + + + + Description + + + + + + + + S1 + + + Maintenance Package Source that produced the SRN + 0: Reserved + 1: Reserved + 2: POST, Firmware + 3: BIST + 4: Service processor, base system controller, etc. + 5: Reserved (potentially for use by AIX + Diagnostics) + 8: Product-Specific Service Guide, MAPs + 9: Reserved (potentially for use by the Problem Solving + Guide) + A-F: Reserved for future extension + + + + + S2 + + + Where applicable, use the lower nibble of the + + + base class code for the IOA definition (see + ). Only 00 to 0C are + currently defined in Revision 2.1, therefore the high nibble is + always zero. (There is a potential exposure that the high + nibble will be defined in the future, but currently there are + 13 base classes defined which include every device class, with + 3 remaining characters for future extension by the PCI SIG. + Therefore the exposure is in the far future.) For non-PCI + devices, use base class 0 to extend the definition (see + ). + + + + + S3-S4 + + + Where applicable, use the + + + subclass code for IOA definition (see + ). Also, extend the + definition to include non-PCI devices where it is not fully + utilized by PCI specification (see + ). + + + + + S5 + + + Unique version of the device/FRU type for a particular + product + + + + + R1 + + + Device/FRU unique failure reason codes. + For POST: assigned by Firmware Developer. + For AIX Diagnostics (S1 = 5, not currently + supported): + 1-7: Use in combination with R2,R3 for diagnostic test + failure when maximum isolation was obtained. + 8-9: Use in combination with R2,R3 for diagnostic test + failure when maximum isolation was NOT obtained. + A: Log analysis of POST error log + B: Log analysis of machine check or checkstop error + log + C: Log analysis of AIX device driver error log + D: diagnostic detected missing resource + E-F: Reserved + For others: assigned by respective developers. + + + + + R2-R3 + + + Device/FRU unique failure reason codes. + For POST: assigned by Firmware Developer + For others: assigned by respective developers. + + + + +
+ + + Current PCI Class Code Definition + + + + + + + + + + + PCI Base Class (lower + nibble)S2 + + + + + PCI Sub-ClassS3-S4 + + + + + Description + + + + + + + + 0 + + + Devices that were built before the class code field was + defined + + + + + 00 + + + All currently implemented IOAs except VGA-compatible + IOAs. + + + + + 01 + + + VGA-compatible IOAs. + + + + + 1 + + + Mass storage controller. + + + + + 00 + + + SCSI bus controller. + + + + + 01 + + + IDE controller. + + + + + 02 + + + Floppy disk controller. + + + + + 03 + + + Intelligent Peripheral Interface (IPI) bus + controller. + + + + + 04 + + + Redundant Array of Independent Disks (RAID) + controller. + + + + + 80 + + + Other mass storage controller. + + + + + 2 + + + Network controller. + + + + + 00 + + + Ethernet controller. + + + + + 01 + + + Token Ring controller. + + + + + 02 + + + FDDI controller. + + + + + 03 + + + ATM controller. + + + + + 80 + + + Other Network controller. + + + + + 3 + + + Display controller. + + + + + 00 + + + VGA-Compatible controller. + + + + + 01 + + + Extended Graphics Array (XGA) controller. + + + + + 80 + + + Other display controller. + + + + + 4 + + + Multimedia device + + + + + 00 + + + Video device + + + + + 01 + + + Audio device + + + + + 80 + + + Other multimedia device + + + + + 5 + + + Memory controller. + + + + + 00 + + + RAM + + + + + 01 + + + Flash + + + + + 80 + + + Other memory controller. + + + + + 6 + + + Bridge IOAs. + + + + + 00 + + + Host bridge + + + + + 01 + + + Reserved + + + + + 02 + + + Reserved + + + + + 03 + + + Reserved + + + + + 04 + + + PCI-to-PCI bridge + + + + + 05 + + + Reserved + + + + + 06 + + + Reserved + + + + + 07 + + + Reserved + + + + + 80 + + + Other bridge device. + + + + + 7 + + + Simple communication controllers. + + + + + 00 + + + Serial controllers. + + + + + 01 + + + Parallel port. + + + + + 80 + + + Other communication controllers. + + + + + 8 + + + Generic system peripherals + + + + + 00 + + + PIC + + + + + 01 + + + DMA Controller. + + + + + 02 + + + System timer + + + + + 03 + + + Real-Time Clock (RTC) controller + + + + + 80 + + + Other system peripherals + + + + + 9 + + + Input devices + + + + + 00 + + + Keyboard controller + + + + + 01 + + + Digitizer (pen). + + + + + 02 + + + Mouse controller + + + + + 80 + + + Other input controllers. + + + + + A + + + Docking stations + + + + + 00 + + + Generic docking station + + + + + 80 + + + Other type of docking station + + + + + B + + + Processors + + + + + 20 + + + PA compliant (PowerPC and successors) + + + + + 40 + + + Co-processor + + + + + C + + + Serial bus controllers + + + + + 03 + + + Universal Serial Bus (USB) + + + + + 04 + + + Fibre Channel + + + + +
+ + + S2-S3-S4 Definition for Devices/FRUs not Defined in + the PCI Specification + + + + + + + + + + + Base ClassS2 + + + + + Sub-ClassS3-S4 + + + + + Description + + + + + + + + 0 + + + 10 + + + AC Power + + + + + 11 + + + DC Power + + + + + 20 + + + Temperature Related Problem + + + + + 21 + + + Fans + + + + + 30-3x + + + Cables + + + + + 40-4x + + + Terminators + + + + + 50 + + + Operator panels + + + + + 60-6x + + + Reserved + + + + + 70-7x + + + Reserved + + + + + 90-9x + + + Reserved + + + + + A0 + + + Boot firmware Heartbeat + + + + + B0 + + + O/S Heartbeat + + + + + D0 + + + Unknown device + + + + + E0 + + + Security + + + + + 1 + + + A0 + + + SCSI Drives (generic) + + + + + B0 + + + IDE Drives + + + + + C0 + + + RAID Drives + + + + + D0 + + + SSA Drives + + + + + E0 + + + Tapes SCSI + + + + + E1 + + + Tapes IDE + + + + + ED + + + SCSI Changer + + + + + EE + + + Other SCSI Device + + + + + EF + + + Diskette drive + + + + + F0 + + + CDROM SCSI + + + + + F1 + + + CDROM IDE + + + + + F2 + + + Read/Write Optical SCSI + + + + + F3 + + + Read/Write Optical IDE + + + + + F4-FF + + + Reserved for other media devices + + + + + 5 + + + A0 + + + L2 Cache Controller including integrated SRAM + + + + + A1 + + + L2 Cache SRAM + + + + + A8 + + + NVRAM + + + + + A9 + + + CMOS + + + + + AA + + + Quartz/EEPROM + + + + + B0-Bx + + + Memory cards + + + + + Cyy + + + Memory DIMMs (yy = memory PD bits) + + + + + 7 + + + A0 + + + I2C bus + + + + + 8 + + + A0 + + + Power Management Functions + + + + + 9 + + + A0-Ax + + + Keyboards + + + + + B0-Bx + + + Mouse(s) + + + + + C0-Cx + + + Dials + + + + + D0 + + + Tablet + + + + + D1-Dx + + + Reserved for other input devices + + + + + B + + + A0 + + + Service processor + + + + +
+ +
+ + diff --git a/Error Handling/ch_notifications.xml b/Error Handling/ch_notifications.xml new file mode 100644 index 0000000..ceea70c --- /dev/null +++ b/Error Handling/ch_notifications.xml @@ -0,0 +1,30 @@ + + + + + Error and Event Notification + + + + + + diff --git a/Error Handling/ch_rtas_error_classes.xml b/Error Handling/ch_rtas_error_classes.xml new file mode 100644 index 0000000..d561d0c --- /dev/null +++ b/Error Handling/ch_rtas_error_classes.xml @@ -0,0 +1,321 @@ + + + + + RTAS Error and Event Classes + + + describes the predefined classes of + error and event notifications that can be presented through the + check-exception and + event-scan RTAS functions. More detailed descriptions + of these classes are given later in this chapter. + defines nodes in the OF device + tree which, through an + “interrupts” property, may list the + platform-dependent interrupts related to each class. From this information, + OSs know which interrupts may be handled by calling + check-exception. The OF structure for describing these + interrupts is defined in + . + This document also defines the mask parameter for the + + check-exception and + event-scan RTAS functions which limits the search for + errors and events to the classes specified. + + + Error and Event Classes with RTAS Function Call + Mask + + + + + + + + + + + Class Type + + + + + OF Node Name(where the + “interrupts” property lists the + interrupts) + + + + + RTAS Function Call Mask(value = 1 enables + class) + + + + + + + + Internal Errors + + + internal-errors + + + bit 0 + + + + + Environmental and Power Warnings + + + epow-events + + + bit 1 + + + + + Reserved + + +   + + + bit 2 + + + + + Hot Plug Events + + + hot-plug-events + + + bit 3 + + + + + I/O Events and Errors + + + ibm,io-events + + + bit 4 + + + + +
+ + + + + R1--1. + + For the Platform Interrupt Event option: The platform + must implement the I/O Events and Errors class type along with the + appropriate + ibm,io-events node property to specify the + interrupts. + + + + + R1--2. + + Platform-specific error and event interrupts + that a platform provider wants the OS to enable must be listed in the + “interrupts” property of the appropriate OF + event class node, as described in + . + + + + + R1--3. + + To enable + platform-specific error and event interrupt notification, OSs must find the + list of interrupts (described in + ) for each error and event class in the + OF device tree, and enable them. + + + + + R1--4. + + OSs must have interrupt handlers for the + enabled interrupts described in Requirement + , which call the RTAS + check-exception function to determine the cause of the + interrupt. + + + + + R1--5. + + Platforms which + support error and event reporting must provide information to the OS via + the RTAS + event-scan and + check-exception functions, using the reporting format + described in + . + + + + + R1--6. + + Optional Extended Error Log information, if + returned by the + event-scan or + check-exception functions, must be in the reporting + format described in + . + + + + + R1--7. + + To provide control + over performance, the RTAS event reporting functions must not perform any + event data gathering for classes not selected in the event class mask + parameter, nor any extended data gathering if the time critical parameter + is non-zero or the log buffer length parameter does not allow for an + extended error log. + + + + + R1--8. + + To prevent the loss of any event + notifications, the RTAS event reporting functions must be written to gather + and process error and event data without destroying the state information + of events other than the one being processed. + + + + + R1--9. + + Any interrupts or interrupt controls used for + error and event notification must not be shared between error and event + classes, or with any other types of interrupt mechanisms. This allows the + OS to partition its interrupt handling and prevents blocking of one class + of interrupt by the processing of another. + + + + + R1--10. + + If a platform chooses to report multiple + event or error sources through a single interrupt, it must ensure that the + interrupt remains asserted or is re-asserted until + check-exception has been used to process all + outstanding errors or events for that interrupt. + + + + + + + Platform Implementation Note: In Requirement + , although the fixed-part return format + for + check-exception and + event-scan is the same, there are some expectations + about what types of error response may be returned from these functions, as + follows: + + + + + The + event-scan function is mainly intended to report only + errors that have been recovered or are non-critical to the OS, since it is + only called on a periodic basis. As such, it should never be used to report + a Severity greater than “WARNING”. More critical errors should + be signaled by an interrupt. Typically, the expected response of an OS to + an + event-scan error report is simply to log the error. The + check-exception function may report error information + of any severity. + + + + + If + event-scan is reporting a critical error (for example, + a checkstop) that occurred before the current boot session, it should not + report it with a “FATAL” Severity, even though the condition + was fatal at the time the failure occurred. The Severity field informs the + OS of the severity of the event at the time of reporting. Errors which + occurred before a successful reboot are no longer critical. Likewise, the + RTAS Disposition field for such an error should be + “FULLY_RECOVERED”. There is a bit in the extended error log to + indicate these “residual” errors. + + + + + Although + check-exception can potentially clean up an error and + return a “FULLY_RECOVERED” disposition, recovery still may not + occur if the MSR + RI bit is not set to 1. It is up to the OS to examine + the RI bit, to determine whether processor state is preserved so that a + return from the machine check interrupt handler can be safely + attempted. + + + + + + + + + + diff --git a/Error Handling/ch_rtas_error_reporting.xml b/Error Handling/ch_rtas_error_reporting.xml new file mode 100644 index 0000000..f53f0f0 --- /dev/null +++ b/Error Handling/ch_rtas_error_reporting.xml @@ -0,0 +1,36 @@ + + + + + RTAS Error and Event Information Reporting + + Architecture Note: All data formats listed in this section are either + referenced as byte fields (and therefore are independent of Endian + orientation), or an indicator in the data structure describes their Endian + orientation. Bits are numbered from left (high-order:0) to right + (low-order:7). + + + + + + diff --git a/Error Handling/ch_service_indicators.xml b/Error Handling/ch_service_indicators.xml new file mode 100644 index 0000000..2f14869 --- /dev/null +++ b/Error Handling/ch_service_indicators.xml @@ -0,0 +1,4168 @@ + + + + Service Indicators + + This chapter defines service indicators + + Note that many times “indicators” are referred to as + “LEDs” as this is one of the most common implementations for + indicators at the current time. + relative to: + + + + Which service indicators may be exposed to an OS and which may + not + + + + The usage model for service indicators, regardless of whether they + are exposed to the OS or not + + + +
+ General + This section gives some general background information required to + understand the service indicator requirements. The service indicator + requirements can be found starting in + . + +
+ Basic Platform Definitions + The following are the definitions of some of the terms used in this + architecture. See also + for additional terms. + +
+ “Enclosure”, Packaging, and Other + Terminology + In order to abstract specific packaging differences between + different products, this architecture uses a number of terms that denote + a unit of packaging. + The term + enclosure means something different, depending on the + product line. Generally this is an entity that can be unplugged and be + removed from the system, but may include the entire system, and generally + encloses other FRUs. It is, however, possible to have a FRU that contains + + one other FRU, and not have it be an enclosure. See + below, for more information. + The concept of the enclosure is very key to this architecture, + because the enclosure provides the anchor point for the Enclosure Fault, + Enclosure Identify, and (when applicable) the Error Log indicators. + + + + For a blade system, a base blade plus any attached + sidecars. + + + A sidecar is a blade that plugs + into a blade slot, but + which is physically connected to the base blade and which cannot be + removed without also removing the base blade and any other attached + sidecars. + + + + The Enclosure Identify indicator is located on the base blade. + Sidecars do not have an Enclosure Identify indicator. + + + + + + A stand-alone computing box, like a deskside unit. + + + + A separately powered box that attaches to a stand-alone computing + box (for example, an I/O expansion tower). + + + + For a rack system, a drawer or partial drawer, with its own power + domains, within a rack system (but not a chassis, in blade system + terms). + + + + FRUs that have one or no internal FRUs are a possible exception to + the above definition of enclosure. The general requirements are that the + enclosing FRU does not need an Error Log indicator (see also Requirement + ), implements the full xipSIA + Lightpath architecture + including FRU Identify, has the enclosing FRU + Fault/Identify and internal (if any) FRU Fault/Identify indicators + visible from the outside of the system the same way that enclosure + indicators would be, and rolls-up the FRU Fault/Identify indicators to + the next level of indicators when there is a next level (for example, + chassis level indicators). Examples of the type of FRUs that the xipSIA + architecture team + might approve as a non-enclosures is: + + + + Appliance drawers (“appliance” means that there are + no field serviceable parts inside). + + + + Appliance Blades, except if they require an Error Log + indicator. + + + + A power supply which comprises two or fewer FRUs. + + + + Fans, but not fan assemblies when the fan assemblies have three + or more Fault indicators. + + + + In addition, the term + System Enclosure (also known as a + Primary Enclosure) is used to denote the enclosure + of a system that contains the one and only Error Log indicator + + Previously known as the System Information (Attention) + indicator. + for the system. An enclosure that is not a System Enclosure is + called a + secondary enclosure. The System Enclosure is + expected to be one that contains at least some of the system processors + for the platform. + + In this chapter, the term + chassis will refer to a blade system chassis. + + Other terminology used in this chapter includes: + + + + activate + + To activate an indicator (physical or virtual) means to + set it to a non-off state (blink, blip, or on). An indicator does not + need to be in the off (deactivated) state prior to being activated (for + example a second request to activate an already active indicator, is also + considered to be an activation of that indicator). + + + + + active state + + An indicator in an active state is in a non-off state. + Different indicator types can be set to a different set of active states. + For each of the following indicators, the following states are applicable + in the indicator active state (See + for more detail on when each + state is applicable and for the conditions under which a state transition + is made): + FRU Identify: blink + FRU Fault: on + Blue Enclosure Identify: on or blink + Enclosure Fault: on or blip + Error Log: on + Blue Rack Identify: on + Blue Row Identify: on + + + + + blip + + A blink state with a short duty cycle used in the + “remind” state for Enclosure Fault Indicators. See also + Requirement + . + + + + + Chassis Enclosure Identify + + An Enclosure Identify indicator at the blade system chassis + level. + + + + + CRU + + See FRU. + + + + + deactivate + + To deactivate an indicator (physical or virtual) means + to set it to the off state. Deactivating a virtual indicator may or may + not deactivate the physical indicator associated with that virtual + indicator (see + ). + + + + + Enclosure Fault + + An amber indicator which indicates, when activated, + that there is a FRU Fault indicator in the enclosure that is + active. + + + + + Enclosure Identify + + An indicator that is used to identify an + enclosure in an installation or an enclosure in a group. This indicator + is blue in color and is turned on in the active identify state. + + + + + FRU + + Field Replaceable Unit. Used to also mean CRU (Customer + Replaceable Unit) in this chapter. + + + + + FRU Fault + + An amber indicator that is used to point to a failing FRU + in an enclosure. + + + + + FRU Identify + + An amber indicator that is used to identify a FRU in + an enclosure or a place where a FRU is to be plugged (for example, for an + upgrade operation). + + + + + Guiding Light Mode + + A platform implementation that provides FRU + Identify indicators for identifying failing FRUs. See + for more information. + + + + + ID + + Shorthand used some places (mainly figures) in this chapter for + “Identify” or “Identify indicator”. + + + + + Lightpath Mode + + A platform implementation that provides FRU Fault + indicators as the general way to identify failing FRUs. See + for more information. + + + + + not visible to the OS + + See transparent to the OS. + + + + + primary level indicators + + The enclosure level indicators. For + example, for rack systems, the enclosure is either the blade, for blade + systems, or the drawer level, for non-blade systems. + + + + + roll-down + + This term is not used by this architecture, but some + people refer to roll-up as the action of activating a higher level + indicator and roll-down as the action of deactivating a lower level + indicator. This architecture will use roll-up for both activation and + deactivation. See roll-up. + + + + + roll-up + + The action of activating a higher level indicator, when a + lower level indicator is activated, and deactivating it when all the + lower level indicators that roll-up to that indicator are deactivated. + For example, if a FRU Fault indicator is activated, it rolls-up and turns + on the Enclosure Fault indicator, and when the last FRU Fault indicator + in an enclosure is deactivated, the Enclosure Fault indicator for that + enclosure is deactivated. + + + + + secondary level indicators + + The indicators on levels below the Primary Level and above the FRU + level. + + + + + SFP + + Service Focal Point. See also + . + + + + + Error Log + + An amber indicator that indicates that the user needs to look at + the error log or problem determination procedures, in order to determine + the cause. + + + + + tertiary level indicators + + The FRU level indicators. + + + + + transparent to the OS + + Indicators whose state cannot be modified or + sensed by OS or application level software. For example, power supply + Fault indicators. + + + + + turn off + + To turn off a physical indicator means exactly like it + sounds. Turning off a virtual or logical indicator may or may not turn + off the physical indicator, depending on the state diagram for the + physical one (see + ). + + + + + visible to the OS + + Indicators whose state can be modified or sensed + by OS or application level software. For PCI Hot Plug indicators. See + also . + + + + +
+ +
+ Service Indicator Visibility and Transparency to the + OS + An indicator is said to be transparent or not visible to the OS + when its state cannot be modified or sensed by OS or application level + software (for example, power supply Fault indicators). An indicator is + said to be visible to the OS when its state can be modified and sensed by + OS or application level software (for example, PCI Hot Plug + indicators). + Requirements on visibility can be found in + . +
+ +
+ Service Indicator + A + service indicator is defined as any indicator that is + used in the course of servicing a system. The intent of service + indicators is + not, in general, to increase system Error Detection + and Fault Isolation (EDFI), but rather to guide the user in performance + of a service action. Usages include (but are not limited to): + + + + Dynamic Reconfiguration (LoPAR indicator type 9002) to indicate + the status of DR operations on a Field Replacable Unit (FRU). More + information on DR indicators can be found in + . This indicator is amber + + The term “amber” will be used in this chapter to mean + any wavelength between yellow and amber. + in color except for some legacy implementations which combined + this indicator with the power indicator, where the color was + green. + + + + An indication of a fault condition of a FRU (LoPAR indicator + type 9006, when OS visible). This indicator is amber in color. The FRU + Fault indicator is handled differently by the platform based on whether + or not the platform is Lightpath Mode platform or Guiding Light + Mode: + + + For Guiding Light Mode platforms, FRU fault indicators are + transparent to the software and therefore have some very specific + requirements relative to their very localized behavior. In this case, + although FRU Fault indicators themselves are transparent to the software, + the associated failure itself, which would activate a FRU Fault + indicator, will be available to the software that handles serviceable + events. + + + + For Lightpath Mode platforms, a FRU fault indicator will be + available to the software and is activated by the detector of the error. + In addition, the FRU Fault rolls up to an Enclosure Fault + indicator. + + + + + + A system-wide indication of a fault or some condition needing + attention in the system. An Error Log indicator (LoPAR indicator type + 9006) is an example of an OS-visible + + For a definition of the visibility or transparency of an + indicator, see + . + indicator of this class of indicators. The Error Log indicator + is a flag to the user that there is something in the system needing + attention, and therefore a starting point to indicate that they should + begin the isolation procedures to determine what needs attention. In a + partitioned system, the physical Error Log + + If the term “virtual” does not appear before + “Error Log”, then the text is referring to the physical + Error Log indicator. + indicator may be the logical OR of individual virtual Error + Log indicators (one virtual Error Log indicator per logical partition and + one for each other separate entity that is non-partition related). This + indicator is amber in color. + + + + An indication of an Identify (locate) operation. An Identify + indicator (LoPAR indicator type 9007) is an example of an indicator of + this class. These indicators may or may not be visible to an OS. In this + capacity, the indicator is activated + + For a definition of what “activate” means, see + . + at the user’s request in order to help them locate a + component in the system (for example, a FRU, a connector, an enclosure, + etc.). This indicator is amber in color, except for the Enclosure, Rack, + and Row Identify indicators, which are blue in color. + + + + An indication of the power state of an entity. This indicator is + platform controlled and is transparent to the OS(s). In addition to the + power state, this indicator may be used to indicate a power failure or + fault. This indicator is green in color. + + + + Environmental indicators such as ambient temperature too high. + These are transparent to the OS. + + + + Hardware only indicators such as Ethernet activity indicators. + These are transparent to the OS. + + + +
+ +
+ Service Indicator Modes + There are two modes that a platform can operate in relative to + service indicators: Lightpath Mode and Guiding Light Mode. Any particular + + platform operates in one and only one mode relative + to service indicators: Lightpath Mode or Guiding Light Mode. A + component (hardware, firmware, or software) which is + designed to be used in both a Lightpath Mode and a Guiding Light Mode + platform needs to be able to operate in both modes. + For guidance in which mode a platform should be designed to + operate, see + . + The following sections give an overview of these two modes. For + specific requirements of each mode, see + . + +
+ Lightpath Mode + The + Lightpath Mode specifies a platform implementation of + service indicators much like what industry-standard servers originally + implemented with its Lightpath, except that FRU indicators also implement + an Identify state along with the current Fault state. The Identify state + overrides the Fault state while the Identify is active for an indicator, + and the indicator is put into the Fault state, if one is pending, when + the Identify is removed. + A summary of the Lightpath Mode is as follows (see + for detailed + requirements): + + + + FRU Fault indicators are used as the general way to identify + failing FRUs. + + + + The physical indicator that implements the Fault indicator states + also implements the Identify indicator states (that is, a FRU Fault + indicator is also a FRU Identify indicator for the same FRU). + + + + This mode is basically a superset of the Guiding Light + Mode. + + + + FRU Fault indicators are presented to the OS for FRUs for which + the OS image is expected to detect errors for either the entire FRU or + part of the FRU. In the latter case, this represents a shared FRU, in + which case the FRU Fault indicator is virtualized, so that one partition + cannot view the setting by another partition, which would allow a covert + storage channel (see also + ). + + + + The OS and firmware are responsible for activating the FRU Fault + indicator for a FRU for which they detect an error. Fault indicators are + reset by the service action on the failing part that they + represent. + + + + FRU Identify indicators are presented to the OS for FRUs that are + fully owned by the OS image. They may also be presented for FRUs that are + partially owned by the OS image. Ownership of a FRU by the OS image is + defined as being the condition of the FRU being under software control by + the OS, a device driver associated with the OS, or application software + running on the OS. In the partially owned case, this represents a shared + FRU, in which case the FRU Identify indicator is virtualized, so that one + partition cannot view the setting by another partition, which would allow + a covert storage channel (see also + ). + + + + Connector Identify indicators are presented to the OS for + connectors that are fully owned by the OS image. Ownership of a connector + by the OS image is defined as being the condition of the connector being + under software control by the OS, a device driver associated with the OS, + or application software running on the OS. + + + + Enclosure Identify indicators are available to the OS when the OS + fully owns a FRU in the enclosure. This indicator is virtualized in a + partitioned system, so that one partition cannot view the setting by + another partition, which would allow a covert storage channel. + + + + The Error Log indicator or virtual copy thereof (for LPARed + platforms) is available to each OS image. + + + + See Requirement + for more information for + requirements on activation of the Fault indicators. + The Triple-S UI, when implemented, also adds additional requires to + Lightpath Mode implementations. See + . +
+ +
+ Guiding Light Mode + A summary of the Guiding Light Mode is as follows (see + for detailed + requirements): + + + + FRU Identify indicators are used as the way of identifying + service procedures like repair, reconfiguration, and upgrade. FRU + Identify indicators are activated/deactivated by user via a user + interface, to identify the FRU(s) involved in the service + procedure. + + + + FRU Identify indicators are presented to the OS for FRUs that are + fully owned by the OS image. Ownership of a FRU by the OS image is + defined as being the condition of the FRU being under software control by + the OS, a device driver associated with the OS, or application software + running on the OS. + + + + Connector Identify indicators are presented to the OS for + connectors that are fully owned by the OS image. Ownership of a connector + by the OS image is defined as being the condition of the connector being + under software control by the OS, a device driver associated with the OS, + or application software running on the OS. + + + + Fault indicators are allowed, but not required, but if provided, + must be transparent to any OS image, and are reset by the service action + on the failing part that they represent. To be transparent to an OS means + that they cannot be controlled by the OS, nor will they interfere with + any other indicator that is controlled by the OS. + + + + Enclosure Identify indicators are provided as part of the + Identify roll-up. Enclosure Identify indicators are available to the OS + when the OS fully owns a FRU in the enclosure. This indicator is + virtualized in a partitioned system, so that one partition cannot view + the setting by another partition, which would allow a covert storage + channel. + + + + The Error Log indicator, or a virtual copy thereof (for LPARed + platforms), is available to the OS. + + + +
+ +
+ +
+ Covert Storage Channels + A + covert storage channel is a path between two entities + that can be used to pass data outside the normal data sharing paths like + LANs. For example, if two OS images were given access to the same + physical indicator and if each OS image could read the state of the + indicator, then the indicator can become a single-bit covert storage + channel between cooperating entities in the two OS images, to pass data + back and forth. This cannot be allowed, for security reasons, and + therefore this architecture defines the concept of virtual + indicators. + A + virtual indicator is provided to each OS image for + each physical indicator that is shared between OS images. The physical + indicator is activated when any virtual indicator for that physical + indicator is activated and the physical indicator is deactivated when all + virtual indicators for that physical indicator are deactivated. The + general OS image can sense what it is trying to set the indicator to, but + cannot sense what the other virtual indicators are set to, and hence no + covert storage channel exists. The exception to the shared access is by a + trusted Service Focal Point (see + for more details). For more + information on how virtual indicators affect the physical indicator + state, see the physical indicator state diagrams later in this + chapter. + An OS image in a partitioned system needs to realize that it may + not have full control over all physical indicators to which it has access + (that is, needs to realize that the indicators may be virtualized in some + cases), and in those cases it should not attempt to indicate to the user + via a user interface the state of the physical indicator which is + controlled by a virtual indicator. + Virtual indicators are controlled by the OS for which they are + generated, except that the platform may activate an OS’ virtual + Error Log indicator if the partition in which the OS resides abnormally + terminates. +
+ +
+ Service Focal Point (SFP) and Service Partition + The + Service Focal Point (SFP), when it exists, will + ultimately be the exclusive common point of control in the system for + handling all service actions which are not resolved otherwise (for + example, via Fault indicators). It interfaces with the error log where + all the serviceable events are stored from the various OS and service + processor diagnostics. The SFP, among other things, allows resetting of + the Error Log light by the user, allows controlling the activation and + deactivation of the FRU, connector, and Enclosure Identify indicators, + and allows the clearing of the service actions in the error log. + The SFP shares access to some of the same indicators as one or more + OS images, but needs access to the physical indicator state, and + sometimes the state of all the virtual indicators for that physical + indicator. If the SFP in a partitioned system were to be implemented on + an OS image that runs non-trusted applications, then the SFP partition + could not be given access to the physical and other OS’ virtual + service indicators, or covert storage channels would exist (see + ) between the SFP partition and + the other OS partitions. This architecture assumes that the SFP is + implemented as trusted or + privileged entity which does not allow non-trusted + applications running on the same OS image as the SFP, and therefore + covert storage channels are not considered to exist between the + SFP’s privileged OS image and other OS images in the system. + The SFP may also be implemented on as a separate entity from the + one being monitored. A system management entity like an HMC interfacing + to the platform via firmware interfaces, or an external system management + entity, are examples of such implementations. + For Lightpath Mode, the Triple-S UI is a user interface that is + associated with a SFP. See + . + The platform’s physical indicators are accessible to the SFP + through the normal indicator interface (LoPAR indicator types 9006 and + 9007). +
+ +
+ Logical Indicators vs. Physical Indicators + A physical indicator is, in many cases, used to represent several + logical and/or virtual indicators. For example, a physical FRU indicator + can be used in Lightpath Mode to represent both a FRU Identify indicator + and a FRU Fault indicator. + The hardware/firmware that implements the physical + indicator’s state machine is the entity which knows about the + combining of the logical and virtual into the physical, and higher level + software (OS and applications) that are given control of a logical or + virtual indicator are only aware of the control of that logical or + virtual indicator, and may not be even able to sense the state of the + physical indicator (that is, can only sense the state of their logical or + virtual ones). + The physical indicator state diagrams in + indicate how logical and + virtual indicators are merged into the physical ones. See also + relative to virtual + indicators. +
+
+ +
+ Machine Classes and Service Strategy + Two broad classifications of computer implementations are defined + here for purposes of defining service indicator implementations. + shows the comparison of these + classes. +   + + Machine Classifications and Service + Characteristics + + + + + + + + + + + Characteristic + + + + + Simple Class + + + + + Complex Class + + + + + + + + Number of FRUs + + + Few + + + Many + + + + + Servicing performed by + + + Customer, generally + + + CE more than customer + + + + + Deferred maintenance + + + Very little + + + Enabled as much as possible + + Deferred maintenance is one of the big drivers towards + use of Guiding Light mode or Lightpath Mode with Triple-S. + That is, having many Fault indicators active at one time + (FRUS waiting for service actions) can lead to confusion when + service is being performed. + + + + + + Concurrent maintenance + + + Generally limited to redundant components (fans, power + supplies) and I/O devices + + + Generally a higher level of concurrent maintenance + + + + + Value of a FRU Fault indicator + + + High + + + Questionable value due to complexity of the system + + + + + FRU Fault indicator implementation + + + Realistic + + + Complex, given the higher level of deferred and + concurrent maintenance + + + + + Console interface + + + Rare + + + Standard + + + + + Platform service mode + + + Lightpath Mode platform + + + Guiding Light Mode platform + or + Lightpath Mode with Triple-S UI + + + + +
+ + Determining whether a platform’s classification, and + therefore the service mode of the platform is dependent on the product + requirements, and is beyond the scope of this architecture, but might + include: + + + + The RAS requirements for the platform. The considerations for + this come from + . + + + + The mixture of machines expected in the environment. Although the + Lightpath Mode and the Guiding Light Mode both contain the identify + capability, and that could be considered to be the common denominator in + servicing in a mixed environment, it could be that there are more + Lightpath Mode platforms in the environment for which a new platform + design is targeted, and therefore it might be desirable to make that new + platform’s mode of operation be the Lightpath Mode for that + reason. + + + +
+
+ General Information about Service Indicators + Indicators may serve multiple uses, but only as defined by this + architecture. For example, a physical indicator used for a FRU is used + for both the FRU Fault and FRU Identify indicators. Non-architected + usages of an architected indicator are specifically disallowed by this + architecture. + In some cases, an indicator may not be visible directly by the user + without removing covers, components, etc. In this case, there is required + to be one or more indicators that are higher in the hierarchy which get + activated in conjunction with the target indicator. This functionality is + called indicator + roll-up. Due to the hierarchy, there might be + multiple indicators that get rolled-up into a single indicator. The + platform (not the OS) is responsible for indicator roll-up. An example of + a roll-up is that on the front of an enclosure + + Note that the enclosure is sometimes called the + “unit,” but a unit is not necessarily a drawer and a drawer + is not necessarily a unit, so the term “unit” is not be + used here. Also note that an enclosure might be a drawer in a rack or + might be part of a drawer. For example, some I/O drawers consist of two + separate and independent enclosures. So, sometimes there may be + multiple enclosure indicators per rack drawer. See also + . + in a rack there is a summary LED that summarizes the Identify + LEDs within or on the back of the enclosure in a rack, and then the + multiple enclosure summary LEDs are summarized at the rack level with a + light on the top of the rack. Another example of a roll-up indicator is + the Enclosure Fault indicator on each enclosure in Lightpath Mode + platforms, which summarizes the Fault indicators within the enclosure. + These roll-up indicators are transparent to the OS, and sometimes to the + firmware, with the exception that the enclosure level Identify indicators + (or virtual versions thereof, in the case of partitioned systems) may be + accessible to the OS via the 9007 indicator type. The indicators that are + provided for roll-up from FRU to enclosure to rack are identified by this + architecture. Platforms may have unique indicators which are not visible + to the OS and which are not defined by this architecture. These will not + share the same indicator as used by one of the indicators which is + architected, including indicators in the roll-up path, except as + explicitly allowed by the architectural requirements in this + architecture. In addition to the roll-up to a higher level indicator for + visibility, the platform may also provide duplicate indicators for some + of the indicators. For example, there may be a front and rear indicator + for the enclosure indicators. These duplicate indicators are not defined + by this architecture except that as for roll-up indicators, the platform + is responsible for controlling any duplicate indicators and for not + making the duplicates visible to the controlling entities. Finally, FRU + indicators are required to be visible to the user during a service + action. This may require, for example, that the indicator be able to be + lit after power is removed from the system, requiring storage of power on + the component with the indicator (for example, via a capacitor) and + activation of the indicators by a push button by the user. + An OS image is given access to the FRU Identify indicators when the + OS image fully owns the resources, and is given access to the Enclosure + Identify indicator for any enclosure in which the OS image fully owns any + resource. An OS image is given access to the FRU Fault indicators when + the OS image owns all or part of the FRU. The Enclosure Fault indicators + are roll-up only indicators and access to these indicators are not given + to the OS. + In a partitioned system (logical or physical), there may be several + virtual Enclosure Identify indicators and one physical Enclosure Identify + indicator. In this case, the OS images are only given access to their + copy of the virtual Enclosure Identify indicator, and do not have direct + access to the physical Enclosure Identify indicator. Activating any + virtual Enclosure Identify indicator which is associated with an + enclosure activates the physical one for that drawer (if not already + activated). Turning off the last virtual Enclosure Identify indicator for + an enclosure turns off the physical one for that enclosure, providing all + other Identify indicators in the enclosure are also off. If software in a + partition senses the state of the virtual Enclosure Identify indicator, + it needs to take into consideration that it may be seeing the virtual + state and not the real state of the indicator, with the virtual state + being what the partition set the indicator to, and this is not + necessarily what the physical indicator is actually displaying. + The Error Log indicator is located on the System Enclosure (the CEC + enclosure) and is used to indicate that there was a failure in the + system. This indicator may also be used by the system to indicate that + some other attention is needed in the system. This Error Log indicator is + the starting point for the determination of the necessary action by the + user. + In a partitioned system (logical or physical), there may be several + virtual Error Log indicators and one physical Error Log indicator. + Activating a virtual Error Log indicator activates the physical one. + Turning off the last virtual Error Log indicator turns off the physical + one. If software in a partition senses the state of the Error Log + indicator, it needs to take into consideration that it may be seeing the + virtual state and not the real state of the indicator, with the virtual + state being what the partition set the indicator to, and this is not + necessarily what the physical indicator is actually displaying. + For Guiding Light Mode platforms, the FRU Identify indicators are + the primary method for pointing to failing FRUs. For Lightpath Mode + platforms, it is expected that the FRU Identify indicators will be used + as a secondary assistance for FRU fault identification (the FRU Fault + indicators being the primary). In both cases, the FRU Identify indicators + can be used to assist with such things as identifying where an upgrade + should be inserted. + The general rules for activation and deactivation of indicators can + be found in Requirements + and + , and more explicit + requirements of individual indicators in the state diagrams in + . When the Triple-S UI is + implemented, see also + . + This architecture assumes that the control of multiple users doing + identify operations at the same time, is under procedural control, and is + not handled or controlled in any way by this architecture, OS, or + firmware. + For Guiding Light Mode platforms, if a FRU contains a Fault + indicator, then the Fault indicator is transparent to the OS and control + of the FRU-level Fault indicator is entirely up to the FRU or to some + OS-transparent method. For example, some power supplies contain a Fault + indicator that does not get reported directly to the system controlling + entity and which is turned off by a button on the power supply which is + pushed when the service is complete. +
+
+ Secondary Light Panels + A secondary light panel may be used to house roll-up indicators as + indicated in the “intermediate” level or + “secondary” level indicators in + and + . These panels may also house + other indicators which would otherwise not have a home (for example, an + over-temperature indicator). + Secondary light panels indicators are not to be used as replacement + for FRU-level indicators. However, if an indicator is not directly + visible when the unit is placed into the service position (for example, + blocked by covers, baffles, cables, etc.), then the secondary light panel + is one implementation to get around this restriction (other + implementations may exist, for example light pipes, etc.). +
+
+ Group Identify Operation + In some systems it may be desirable to identify a set of enclosures + as being part of a group. This is called a group identify operation and + can be performed by activating the appropriate Enclosure Identify + indicators. + For platform or systems that consist of multiple enclosures, it may + be necessary to change the state of one enclosure before servicing + another enclosure. For example, a system drawer (primary enclosure) may + need to be powered down before servicing an I/O drawer (secondary + enclosure). It may be useful in this case for the servicer to be able to + identify the various enclosures that are linked. In such implementations, + the enclosures should be designed with a method to activate the Group + Identify function, with the “group” being all linked + enclosures. One implementation of this is to put a pushbutton in + proximity to the blue Enclosure Identify indicator, which is then used to + activate the blue Enclosure Identify indicators of all connected + enclosures, and subsequently to deactivate all of them. It is suggested + that with this implementation of the Group Identify function, that this + switch toggle the Group Identify function for this set of enclosures, + with each push toggling the Group Identify function. If it takes awhile + to activate all the blue Enclosure Identify indicators in the group, it + may be useful to give the user feedback that the button has been pressed. + One way to do this is to put the blue Enclosure Identify indicator next + to the pushbutton into the blink state (momentarily) until all the other + blue Enclosure Identify indicators in the group have been activated, and + when that is complete, to put this indicator into the Identify state (on + solid). +
+ +
+ System-Level Diagrams + The following figures are conceptual diagrams showing indicator + roll-ups: + + + + . + + + + . + + + + . + + + + +
+ Representation of the Indicators -- Lightpath Mode Platform + + + + + + + + +
+ +
+ Representation of the Indicators -- Guiding Light Mode Platform + + + + + + + + +
+ +
+ Representation of the Indicators -- Rack System + + + + + + + + +
+ Note: Guiding Light Mode platform shown, + with optional Enclosure Fault indicators. For Lightpath Mode platforms, + FRU Fault indicators would always exist and would roll up to the Enclosure + Fault indicator, and additionally, the Rack and Row Identify indicators would + have an additional Fault indicator (not shown) and the Fault indicators at the + enclosure level would roll up to those. +
+ +
+ +
+ Service Indicator Requirements + Service indicators are required on all platforms. + + + + R1--1. + + All platforms must implement either the + Lightpath Mode or the Guiding Light Mode of service indicators, and all + components and enclosures (the primary enclosure and any secondary + enclosures (for example, I/O expansion drawers)) within the platform must + be operating in the same mode. + + + + + R1--2. + + Indicators defined by this architecture must + not be used for any purpose other than is what is specified by this + architecture, and only with the specific states defined by this + architecture. + + + + R1--3. + + All platforms must provide the + “ibm,service-indicator-mode” property in + the Open Firmware Device Tree root node. + + + + + +
+ Service Indicator General Requirements + This section details requirements of indicators that are not + specifically LoPAR indicator type 9006 or 9007 related. These are true + even if the platform does not present any 9007 indicators to the OS. This + includes requirements for platform actions like roll-up. For 9006 and + 9007 specific requirements, see + . + Requirements which are prefaced by + “For Lightpath Mode platforms:” + only apply to + Lightpath Mode platforms. Requirements which are prefaced by + “For Guiding Light Mode platforms:” + only apply + to Guiding Light Mode platforms. Requirements that are prefaced by + neither, apply to both Lightpath Mode and Guiding Light Mode platforms. + Components which are designed to work in both + Lightpath Mode and Guiding Light Mode platforms, need to be able to + comply with both Lightpath Mode and Guiding Light Mode sets of + requirements, as well as the requirements that apply to all. + +
+ Fault Detection and Problem Determination + Requirements + There are two general classifications of problems which are + indicated by Service Indicators: + + + + An indication for FRUs that have failed and need to be + replaced + + + + An indication of other system problems that may be causing + performance degradation or which might cause failures in the future, for + example: + + + + A FRU that is predicted to fail (may be treated as a failing FRU + by some implementations) + + + + An over temperature conditions + + + + A loss of redundancy that is not caused directly by a FRU failure + (for example, greater than 100% of the power of the base power being + used) + + + + A configuration problem such as a missing resource, resource + plugged into the wrong slot, or invalid configuration + + + + + + The general model for use of the Error Log + + Previously called the System Information (Attention) + indicator. + and Enclosure Fault indicators is to indicate problems as + follows: + + + + Activation of either the Error Log or Enclosure Fault indicators + is accompanied by a log entry in an error log that can be queried by the + user + + + + Activation of the Error Log indicator is used when the user needs + to perform some procedure, or acknowledge some condition, prior to taking + corrective action + + + + For most types of problems, this requires the user to look into + the error log at the start of the procedure + + + + In some cases (generally for more common or more urgent + problems), additional indicators may be provided by a system and + activated to allow the user to determine the problem without looking into + the error log (these additional indicators are generally not allowed to + be the same indicators as defined by this architecture, except as allowed + by this architecture) + + + + The procedure performed by the user may include items + like: + + + + Activation of FRU Identify indicators (for example, as in Guiding + Light Mode systems) + + + + Removal and re-connection of cables, reseating of cards, + etc. + + + + + + + + Activation of an Enclosure Fault (Lightpath Mode systems) is only + allowed in the following cases: + + + As an indication of the roll-up of a FRU Fault indicator + + + + In conjunction with a system error that prevents a FRU Fault + indicator from being activated (this requires some other indication of + the global failure problem, for example, an error code on an op + panel) + + + + + + The following requirements define the actions to be taken by a + system on the detection of a fault. + + + + R1--1. + + The detector of a fault condition must do the following: + + + + If the a fault + occurs which cannot be isolated appropriately without the user performing + some procedure, then activate the Error Log indicator. + + + + If a fault occurs + which can be isolated to a single FRU and if there exists a Fault + indicator for the FRU, then activate that FRU Fault indicator, otherwise + activate the Error Log indicator. + + + + If a fault occurs + which cannot be isolated to a single FRU and if there exists a Fault + indicator for the most likely FRU in the FRU list, then activate that FRU + Fault indicator, otherwise activate the Error Log indicator. + + + + If a fault occurs + which is isolated to a group of FRUs (called a FRU group) and if there + exists a Fault indicator for each of the FRUs, then activate all the FRU + Fault indicators, otherwise activate the Error Log indicator. + + + + See also, + . + + + + + R1--2. + + (Requirement Number Reserved For + Compatibility) + + + + + R1--3. + + Service Indicators (Error Log, Fault, and Identify) must be activated + appropriately to guide a user to or through a service action or + procedure. + + + + + R1--4. + + Service Indicators (Error Log, Fault, and Identify) must be deactivated + appropriately, as follows: + + + + A Service Indicator activated by an entity must be automatically + deactivated by that entity when that entity can determine that the + activation is no longer necessary, or + + + + A Service Indicator must be automatically deactivated by the + platform when the platform can determine that the activation is no longer + necessary or may be necessary but will be redetected and therefore + reactivated a reasonable time later, or + + + + A Service Indicator must be automatically deactivated by a + service procedure which fixes the issue that caused the indicator to be + automatically activated in the first place, or + + + + A Error Log or Identify indicator must be deactivated when a + user request it to be deactivated by a system-level user + interface. + + + + For the Lightpath UI Base Enablement, as indicated in + Requirement + and + . + + + + + + + R1--5. + + For each + activation of the Error Log and Enclosure Fault Indicators, one of the + following must be true: + + + + If the platform + is functional enough to allow it, then an associated entry must be made + in an error log that can be queried by a user interface. + + + + In the case where + the platform is not functional enough to allow logging of an error log + entry, then there must exist a way for the user to determine the failure + associated with the indicator activation (for example, an error code on + an op panel on the system). + + + + + Implementation Notes: + + + + + Requirement + are intentionally written + general enough so that different platform types have some latitude in + implementation of Service Indicators. However, see the state diagrams, + , for some explicit + requirements for activation and deactivation of the various Service + Indicators. Those state diagrams take precedence over Requirement + . When the state diagrams and + Requirement + do not give explicit direction + for implementation, implementers should consider compatibility with + existing implementations when making decisions about activation and + deactivation. + + + + 2. In Requirement + , the physical indicator may + not be turned off when deactivated from an OS interface (versus a + system-level interface), if another entity outside of that OS also has + the physical indicator activated. That is, if the physical indicator is + the combination of several logical indicators. + + + + + + + R1--6. + + The Error Log + indicator must be activated only for Serviceable Events. Serviceable + Events are platform, global, regional and local error events that require + a service action and possibly a call home when the serviceable event must + be handled by a service representative or at least reported to the + service provider. Activation of the Error Log indicator notifies the + customer of the event and the event indicates to the customer that there + must be some intervention to rectify the problem. The intervention may be + a service action that the customer can perform or it may require a + service provider. + + + + +
+ +
+ FRU-Level and Connector Indicator Requirements + The indicators specified in this section represent the lowest level + indicators in the indicator roll-up hierarchy. + See also requirements in + . + For the Lightpath UI, see also the requirements in + . + + + + R1--1. + + For Lightpath Mode platforms: + All of the following must be true: + + + + A FRU Fault indicator must be implemented for every replaceable + FRU, with the states of “off” and “on,” except + for FRUs which are excepted in Requirement + . + + + + Clearing of the FRU Fault indicator from the Fault state must be + the result of part of the repair action and must be transparent to the + OS(s) and SFP (that is, the OS or SFP is not required to automatically + clear a FRU Fault indicator). + + + + The physical indicator which implements the FRU Fault indicator + must also be Identify indicator and follow the requirements for Identify + indicators. + + + + + + + R1--2. + + FRU indicators + (Fault and Identify) must be visible to the user during a service + action. + + Implementation Note: Requirement + may require, for example, that + the indicator be able to be lit after power is removed from the system, + requiring storage of power on the component with the indicator (for + example, via a capacitor) and activation of the indicators by a push + button by the user (see Requirement + for requirements on this + implementation). Another example would be via the use of a light pipe + from the indicator to a visible place. + + + + + R1--3. + + For Guiding Light Mode platforms: + If a FRU Fault + indicator exists, then it must be transparent to the OS, SFP, and HMC and + it must be independent of, and not physically combined into the same + indicator with, any indicator defined by this architecture, including the + setting of, resetting of, and displaying of the state of that indicator, + except that a FRU Identify indicator may be activated to the Fault state + (on solid) as a result of a FRU failure if all of the following are + true: + + + + The failure that is being indicated must be a failure which + prevents the user from activating the said FRU Identify indicator to the + Identify state. + + + + Clearing of the FRU Fault indicator must be the result of part + of the repair action and must be transparent to the OS, SFP, and + HMC. + + + + + Architecture Notes: + + + + + For Guiding Light Mode platforms, the only FRU-level indicators + that are allowed to be visible to an OS, SFP, or HMC are the FRU Identify + indicators. + + + + For Guiding Light Mode platforms, the only Fault indicator that + is allowed to be visible to an OS, SFP, or HMC is the Error Log + indicator. + + + + Examples of the exception of the use of FRU and enclosure + indicators in Requirement + as an indication of a fault + are: when the path for controlling an Enclosure Identify indicator or FRU + indicator in that enclosure is broken, or when the power supply in the + enclosure is broken and the indicator cannot be activated to the Identify + state. In these cases the FRU and/or enclosure indicators may be + activated (transparently) to the Fault state to indicate the failure, and + would be returned to the Normal state as a result of the repair action + that fixes the problem. + + + + + + + R1--4. + + All platforms + designs, except very low end servers, + + The term “very low end servers” is not explicitly + defined here, but is used to refer to implementations where FRU-level + indicators cannot reasonably be implemented (for example, due to size + constraints) or where the product can show explicit financial + justification for not implementing. + must include an Identify indicator for every FRU with the + states of “off” and “blink,” except for the + following classes of FRUs: + + + + If a device + driver has access to some standard form of Identify/Fault indicators for + the DASD devices it controls (for example, some standard form of + enclosure services), then the platform does not need to provide FRU + indicators for these devices. + + + + If a device + driver has access to some standard form of Identify/Fault indicators for + the removable media devices it controls (for example, some standard form + of enclosure services), then the platform does not need to provide FRU + indicators for these devices. + + + + External + enclosures other than PCI expansion enclosures, and external devices (for + example, keyboard, mice, tablets) that attach via cable to IOAs, do not + require FRU indicators. + + + + Cables that connect from IOAs to the devices defined in parts + , + , and + + of this requirement do not require FRU indicators. + + + + Internal cables, interposers, and other FRUs which do not + contain active components do not require FRU indicators. + + + + + Implementation Note: Even though an item falls into + the list of possible exceptions in Requirement + , the designer of such a + component should verify that leaving off the FRU Identify indicator from + their component will not prevent the systems in which that component is + used from meeting their serviceability requirements. + + + + + R1--5. + + All FRU-level + Identify indicators must implement the state diagram shown in + , except that the Fault state + is not required for Guiding Light Mode platforms. + + + + + R1--6. + + All platforms + must include an Identify indicator with the states of “off” + and “blink” for every connector that is to be involved in an + Identify operation. + + + + + R1--7. + + FRU-level and + connector-level indicators must be made visible to the OS(s) as follows, + and must be made transparent otherwise: + + + + For Lightpath Mode platforms: FRU Fault indicators + must be made visible to the OS for FRUs for which the OS image is + expected to detect errors for either the entire FRU or part of the + FRU. + + + + FRU Identify indicators must be made visible to the OS for FRUs + that are fully owned by the OS image. + + + + Connector Identify indicators must be made visible to the OS for + connectors that are fully owned by the OS image and for which a connector + Identify indicator exists. + + + + + Implementation Notes: + + + + + In Requirement , for FRU Fault indicators that + are shared, the FRU Fault indicator is virtualized, so that one partition + cannot view the setting by another partition, which would allow a covert + storage channel (see also + and + ). + + + + Ownership of a FRU or connector by the OS image is defined as + being the condition of the FRU or connector being under software control + by the OS, a device driver associated with the OS, or application + software running on the OS. + + + + + + + R1--8. + + An OS which activates a FRU Identify + indicator must provide a method of deactivating that indicator. + + + + + R1--9. + + (Requirement Number Reserved For + Compatibility) + + + + +
+ +
+ Enclosure-Level Indicator Requirements + See also requirements in + . + For the Lightpath UI, see also the requirements in + . + + + + R1--1. + + On the System Enclosure: + The platform must + implement an Error Log indicator and all of the following must be + true: + + + + The states of “off” and “on” must be + implemented and must be used for the Error Log function + + + + (Requirement Number Reserved For Compatibility) + + + + + This indicator must roll-up to the rack indicator, when the rack + indicator is implemented, and for blade implementations, to the Chassis + Error Log indicator. + + + + The indicator must implement the state diagram shown in + . + + + + The platform must provide a mechanism to allow the user to put + the Error Log indicator into the off state. + + + + + + + R1--2. + + Except for enclosures that contain only + FRUs that are exempted from FRU-level indicators as specified by + Requirement + parts + , + , and + , and which also do not have + any Connector Identify indicators, the platform must implement an + Enclosure Identify indicator on all enclosures, and all the following + must be true: + + + + The states of “off,” “blink,” and + “on” must be implemented and must be used for the Identify + function. + + + + This indicator must roll-up to the rack indicator, when the rack + indicator is implemented, and for blade implementations, to the Chassis + Enclosure Identify indicator. + + + + The indicator must implement the state diagrams shown in + and + . + + + + + + + R1--3. + + For Lightpath Mode Platforms: All the following must + be true for the Enclosure Fault indicator: + + + + The platform must implement an Enclosure Fault indicator on each + enclosure in which there exists at least one FRU Fault indicator. + + + + These indicators must implement the states of “off,” + “on,” and “blip”. + + + + These indicators must implement the state diagram as shown in + . + + + + These indicators must not be visible to any OS image. + + + + The platform must + provide a mechanism to allow the user to put each Enclosure Fault + indicator into the blip state. + + + + This indicator must roll-up to the rack indicator, when the rack + indicator is implemented, and for blade implementations, to the Chassis + Enclosure Fault indicator. + + + + + + Implementation Note: One way of achieving Requirement + is to provide a pushbutton (for + example, on the secondary indicator panel). + + + + + R1--4. + + (Requirement Number Reserved For Compatibility) + + + + + R1--5. + + (Requirement Number Reserved For Compatibility) + + + + + R1--6. + + Enclosure-level + indicators must be made visible to the OS(s) as follows, and must be made + transparent otherwise: + + + + Enclosure + Identify indicators must be made visible to the OS when the OS fully owns + a FRU in the enclosure. + + + + The Error Log indicator must be made visible to each OS image. + + + + + Implementation Notes: + + + + + In Requirement + , for indicators that are + shared, the indicator is virtualized, so that one partition cannot view + the setting by another partition, which would allow a covert storage + channel (see also + and + ). + + + + Ownership of a FRU by the OS image is defined as being the + condition of the FRU being under software control by the OS, a device + driver associated with the OS, or application software running on the + OS. + + + + + + + R1--7. + + An OS which + activates an Error Log indicator must provide a method of deactivating + that indicator, when such an activation is not be deactivated + automatically as part of the service action. + + + Implementation Note: Relative to Requirement + , it is recommended that an OS + that activates an Error Log indicator, provide a way to deactivate that + indicator, regardless of whether that indicator would be reset as part of + a service action. + + + + + R1--8. + + An OS which activates an Enclosure + Identify indicator must provide a method of deactivating that + indicator. + + + + + R1--9. + + (Requirement Number Reserved For Compatibility) + + + + + R1--10. + + For Guiding Light Mode Platforms: If a FRU Fault + indicator exists, then it must not roll-up to the Enclosure Identify or + Error Log indicator, and if there is such a requirement to roll-up such + an indicator, then the enclosure must implement an Enclosure Fault + indicator, with the same requirements as the Enclosure Fault indicator + for Lightpath Mode platforms. + + + + +
+ +
+ + Rack-Level Indicator Requirements + + See also requirements in + . + + + + R1--1. + + If a platform implements a rack-level + indicator then all of the following must be true: + + + + The rack indicator must be transparent to the OS, SFP, and + HMC. + + + + The rack indicator must be Highly visible + + As defined by our usability groups + (distance and viewing angle) with covers in place. + + + + For Lightpath Mode: The rack tower indicator must + implement the state diagram indicated in + , + , and + . + + + + For the Guiding Light Mode: The rack tower indicator + must implement the state diagram indicated in + , + , and if the optional Enclosure + Fault indicators are implemented, then + . + + + + + + +
+ +
+ Row-Level Indicator Requirements + + + + R1--1. + + If a system implements a row-level + indicator to roll-up a row of rack-level indicators, then the following + must be true for these indicators: + + + + The indicator must be transparent to the OS, SFP, and + HMC. + + + + For Lightpath Mode: This indicator must implement the + state diagram indicated in + , + , and + . + + + + For the Guiding Light Mode: This indicator must + implement the state diagram indicated in + , + , and if the optional Enclosure + Fault indicators are implemented, then + . + + + + + + +
+ +
+ Shared Indicator (Multiple Partition System) + Requirements + To avoid covert storage channels (see + ), virtual indicators are + required for physical indicators which are shared between OS + images. + + + + R1--1. + + If a physical + indicator (Fault or Identify) is shared between more than one partition, + all the following must be true: + + + + Except where there is explicit trust between the partitions, the + platform must provide a separate virtual indicator to each non-trusted + partition for each shared physical indicator and must control the + physical indicator appropriately, as indicated in the state diagrams in + . + + + + If software in a partition senses the state of the virtual + indicator, it must take into consideration that it is seeing the virtual + state and not the real state of the indicator, with the virtual state + being what the partition set the indicator to, and this is not + necessarily what the physical indicator is actually displaying. + + + + The SFP must be given access (sense and set) to the physical FRU + level indicators, and the platform must clear all the corresponding + virtual indicators when physical indicator is cleared by the SFP. + + + + The SFP must be given access (sense and set) to the physical + Error Log indicator, and the platform must not clear the corresponding + virtual indicators when physical indicator is cleared by the SFP. + + + + + Architecture Note: + + + + + In Requirement + , an example of “explicit + trust” is where the sharing partitions are the SFP and one other + partition, where the SFP is running in an OS where all the applications + and drivers can be trusted to not open a covert channel to the other OS + or application in that other partition. + + + + In Requirement + , it may be possible for the + SFP to get direct access to the virtual indicators, but such access is + beyond the scope of this architecture. + + + + + + +
+ +
+ Additional Indicator Requirements + + + + R1--1. + + A user interface which presents to a + user the state of the Identify indicators or which allows the user to set + the state of the Identify indicators, must be prepared for an indicator + to disappear from the list of indicators available to the OS image (for + example, a “no such indicator” response to a set request), + and must provide the user with an appropriate message and recovery (for + example, prompt the user whether they want to refresh the list of + available indicators). + + + + + R1--2. + + The color of indicators must be as follows: + + + + FRU Identify, FRU Fault, Enclosure Fault, Error Log indicators, + and any roll-up indicators for Error Log (rack-level, blade system + chassis-level, and row-level) must be amber. + + + + The Enclosure Identify indicators and any roll-up indicators for + these indicators (rack-level, blade system chassis-level, and row-level) + must be blue. + + + + + + + R1--3. + + The blink rate of + all Identify indicators which blink, must be nominally 2 Hz (minimum 1 + Hz) with a nominal 50% duty cycle. + + Implementation Note: The 1 Hz rate should not be used + unless absolutely necessary. The 1 Hz rate is put in to be consistent + with the industry standard SHPC specification, which specifies 2 Hz with + 1 Hz minimum. + + + + + R1--4. + + The + “blip” rate for the Enclosure Fault indicators when in the + “remind” state must be nominally 0.5 Hz with a duty cycle of + 0.2 seconds on, 1.8 seconds off. + + + + + R1--5. + + All indicator roll-up (activate and + deactivate) must be controlled entirely by the platform and must be + transparent to the OS, SFP, and HMC. + + + + + R1--6. + + Duplicate indicators that are + implemented to reflect the same state as another indicator in the system + (for example, an indicator on the back of an enclosure that is to reflect + the same visible state as the enclosure indicator on the front of the + enclosure) must be transparent to the OS and must be kept synchronized by + the platform. + + + + + R1--7. + + The platform must + provide a way to light all the indicators (Identify, Fault, Error Log, + etc.) without any OS present, for test purposes (manufacturing, field + service, etc.). + + + + + R1--8. + + The hardware must provide the firmware a + way to read the state of the indicators (that is, the register which + controls the visual state, not the actual visual state) as well as to set + the state of the indicators. + + + + + R1--9. + + The platform must + be designed such that permanently removing a FRU does not remove the + capability to use the Identify indicator(s) remaining in the platform or + affect any roll-up. + + + + + R1--10. + + In reference to + Requirement , if a capacitor and pushbutton + are used to be able to activate the indicator after removal of the part, + then all the following must be true: + + + + For Lightpath Mode platforms: Both + the Identify and + the Fault states must be supported, and the indicator must activate when + the push button is depressed and must go off (with the remaining + capacitor charge maintained) when the pushbutton is released (Identify + state is displayed as “blink” and Fault state as + “on”). + + + + For Guiding Light Mode platforms: + The Identify state + must be supported, and the indicator must activate (“blink”) + when the push button is depressed and must go off (with the remaining + capacitor charge maintained) when the pushbutton is released. + + + + There must be a + green indicator next to the pushbutton and the indicator must get turned + on when the button is pressed and when there is charge in the capacitor, + and must be off when the button is not pressed. + + + + The capacitor must have the capability to store enough charge + for two hours and after that period must be able to light for 30 seconds + the green indicator and enough other indicators to be able to identify + any necessary group of FRUs (for example, four additional indicators if a + group of four DIMM locations is to be identified simultaneously). + + + + + Implementation Note: As part of Requirement + , it is not necessary to + roll-up any activated indicators to the next level when the button is + pressed. + + + + + R1--11. + + All indicators which are under standby + power must work the way they do when full power is applied to the system, + including all of the following: + + + + The indicators must continue to display the last state displayed + when the system power went to standby-only power, unless the state is + changed during the standby state by the user or by a service + action. + + + + The changing of the state to the Identify state and then back to + the previous state by the user must be supported, when that functionality + is supported during full system power. + + + + + Implementation Note: Internal to the platform + firmware, it will most likely be required to have a common control point + for all service indicators in order to meet the requirements and meet the + necessary state information + + + + + R1--12. + + Any secondary (intermediate) level + roll-up indicator (see + ) must behave as + follows: + + + + Be blinking, if any Identify indicator that it represents is + blinking + + + + Be on solid if any Fault indicator that it represents is on and + no Identify indicator that it represents is blinking + + + + Be off if all indicators that it represents are off + + + + + + + R1--13. + + The icons used for the following indicators, and any + roll-up of the same, must be as follows (see the usability specifications + for size, color, and placement): + + + + For the Error Log indicator: + + + + + + + + + + + + + + For the Enclosure Fault indicator: + + + + + + + + + + + + + + For the Enclosure Identify indicator: + + + + + + + + + + + + + + + + +
+ +
+ Blade Systems Chassis-level Indicator + Requirements + The following describes the chassis-level Error Log and Enclosure + Identify indicator requirements for blade chassis implementations. These + are basically the same as for the rack and row level indicators, except + that the Enclosure Identify indicators are required to be able to be + turned on/off by a user interface, unlike the rack and row level + indicators. + For the Lightpath UI, see also the requirements in + . + + + + R1--1. + + The blade chassis + must implement an amber Error Log indicator, with the state diagram + indicated in + . + + + + + R1--2. + + The blade chassis + must implement an amber Enclosure Fault indicator, with the state diagram + indicated in + . + + + + + R1--3. + + The blade chassis + must implement an blue Enclosure Identify indicator, with the state + diagram indicated in + . + + + + +
+ +
+ Service Indicator State Diagrams + The following state diagrams show the transitions and states for + the service indicators in the system. + + Implementation Note: Activation of an + indicator by a + roll-up operation from a lower level indicator will prevent a user from + turning off such an indicator from a user interface without turning off + the lower level indicator. It is recommended, if possible, that in the + user interface that allows the user to attempt to deactivate an + indicator, provide to the user a message that the indicator cannot be + deactivated, if attempted, when a roll-up to that indicator is active. + That is, something better than just silently not turning off the + indicator. Alternatively, the user can be shown that the option of + turning off such an indicator is not possible, when a roll-up to that + indicator is active (for example, by graying out the option on the user + interface). + +
+ FRU or Connector Fault/Identify + Indicator State Diagram + + + + + + + + +
+ + Notes: + + + Not being available means the failure that is being + indicated must be a failure which prevents the user from + activating the Identify for the FRU. + + + + Transition to Fault state may occur if a failure + occurs which would prevent the activation of the indicator + into one of the Identify states. Not all FRU Fault indicators + in an enclosure get activated like this simultaneously; + only those that are directly involved with the fault + (for example, like the FRU Fault indicator associated with + the indicator controller hardware) + + + + OS is not expected to change an + indicator from Fault to Normal, but is permitted to do so + (providing that it has access to the indicator because it + owns the resource). + + + + Transition from Fault to the Identify + or Normal states by the OS may not be possible if a hardware + fault causes a failure which prevents access to the + indicator. + + + + Format on the above diagram of “xxxx,y” means a + call to the set-indicator or + ibm,set-dynamic-indicator + RTAS call with an indicator token of “xxxx” and a state + value of “y” (only the token applicable for the specific + indicator causes a state transition). + + + + The 9002 Identify and Action are the same state. + + + + 9006 FRU-level indicators only + provided in Lightpath Mode platforms. + + + + Fault indicators may be virtualized, + with several OS images and firmware given access to a virtual + FRU Fault indicator which controls the same physical + Fault/Identify indicator. These get combined as shown in the state + diagram, above; all virtual Fault indicators basically get + ORed together. + + + + This indicator may be forced to the Normal (off) + state under certain circumstances (for example, see Requirement + ). + + + + For the Lightpath UI, when implemented, + other transition conditions are possible. See + + for requirements. + + + + +
+ Error Log + Indicator State Diagram + + + + + + + + +
+ + Notes: + + + Format on the above diagram of “xxxx,y” means + a call to the set-indicator or + ibm,set-dynamic-indicator + RTAS call with an indicator token of “xxxx” and a state + value of “y” (only the token applicable for the + specific indicator causes a state transition). + + + + This indicator may be forced to the Normal + (off) state under certain circumstances (for example, see + Requirement + ). + + + + See Requirement + . + + + + For the Lightpath UI, when implemented, other transition conditions + are possible. See + + for requirements. + + + + +
+ Enclosure + Identify Indicator State Diagram for Scalable Systems + + + + + + + + +
+ + Notes: + + + This indicator may be forced to the Normal (off) + state under certain circumstances (for example, see Requirement + ). + This indicator is off at the end of POST. + + + + The states in this diagram overlay the corresponding + states in + . + This figure represents the POST states and + + the after-POST states. + + + + The use of the Optional Identify state to indicate boot + identify is only to be used for boot servers + for scalable system nodes or blades of a blade system + (for example, NUMA system nodes), and not for stand-alone + systems or blades + + + + +
+ Enclosure + Identify Indicator State Diagram + + + + + + + + +
+ + Notes: + + + This indicator may be activated to the on state + by any OS which is given access to the indicator per Requirements. + For indicators that are shared by multiple OS instances, this indicator + is virtualized (see + + and + ). + LoPAR compliant OSs are only given the capability to activate the + Enclosure ID to the on state, not to the blink state. The blink state + may be activated through an external platform management interface by + a user request through that interface to blink the physical Enclosure ID. + + + + This indicator may be forced to the off state under + certain circumstances (for example, see Requirement + ). + This indicator is off at the end of POST. + + + + A user is not allowed to deactivate the Enclosure ID if + there are still FRU IDs still active. + + + + A user request through a privileged user interface (for example, + via an SFP) to set the physical Enclosure ID to off, + forces any virtual Enclosure ID indicators that are active (on or + blink) to their off state, but this does not override + any FRU ID roll-ups (see Note + ). + + + + For Scalable (NUMA) systems, the states in this diagram + overlay the corresponding states in + . + This figure represents the after-POST states and + . + the POST states. + + + + A virtual Enclosure ID can be activated or turned off by the + 9007 indicator token for the target Enclosure ID. + + + + +
+ Enclosure Fault + Indicator State Diagram + + + + + + + + +
+ + Notes: + + + There is no direct activation or deactivation of + this indicator by any OS. + + + + See Requirement + + and the Implementation Note below that requirement. + + + + This indicator may be forced to the Normal (off) + state under certain circumstances (for example, see Requirement + ). + + + + Activation of an Enclosure Fault indicator without + activating a FRU Fault indicator within the + enclosure is to be used only in exceptional cases where + the FRU Fault cannot be activated. In + such cases the system is required to also provide + further direction to the user on how to resolve + the fault (for example, by providing an error code on an + op panel on the system). + + + + +
+ For Blade Systems: + Chassis-level Error Log Indicator State Diagram + + + + + + + + +
+ +
+ For Blade Systems: + Chassis-level Fault Indicator State Diagram + + + + + + + + +
+ +
+ For Blade Systems: + Chassis-level Enclosure Identify Indicator State Diagram + + + + + + + + +
+ + Notes: + + + This indicator may be forced to the Normal (off) state + under certain circumstances (for example, see Requirement + ). + + + + A user is not allowed to deactivate the chassis Enclosure + ID if there are still FRU Identify or Blade Enclosure + Identify indicators still active (see state transition qualifiers + in the above diagram). + + + + A user request to set the Chassis Enclosure ID to the + Identify (blink) state temporarily overrides roll-up + operations (roll-up operations set the indicator to the on state). + + + + A user request to change state of the Chassis Enclosure + ID cancels any previous user request against the + same indicator, replacing the user requested state with the new state. + + + + +
+ Rack-level Error + Log Indicator State Diagram + + + + + + + + +
+ +
+ Rack-level Fault + State Indicator Diagram + + + + + + + + +
+ +
+ Rack-level + Enclosure Identify Indicator State Diagram + + + + + + + + +
+ +
+ Row-level Error + Log State Diagram + + + + + + + + +
+ +
+ Row-level Fault + State Diagram + + + + + + + + +
+ +
+ Row-level + Identify State Diagram + + + + + + + + +
+ + Notes: A blinking Enclosure ID + is assumed to be “active” for purposes of the Row Enclosure ID indicator + state. +
+ +
+ +
+ Requirements for 9002, 9006, and 9007 Indicators + See + for service indicator + requirements that are not 9006 and 9007 specific. + + + + R1--1. + + When the platform + presents a 9006 indicator to an OS, the following must be true: + + + + The platform must set the location code of the Error Log (9006) + indicator and sensor to be the location code of the system and this + indicator or sensor must be the first one in the list of 9006 indicators + or sensors. + + + + For Lightpath Mode platforms: + The platform must set + the location code of each FRU Fault indicator and sensor to be the + location code of the component to which that indicator or sensor is + associated. + + + + For every 9006 indicator, there must be a corresponding 9006 + sensor which has the same index as the corresponding indicator. + + + + + + + R1--2. + + When 9007 + indicators are to be provided to an OS, the platform must implement the + ibm,get-indices RTAS call and must present that call + in the device tree for the OS, and the OS needing access to the 9007 + indicators and sensors must use the + ibm,get-indices call to get the indices of the 9007 + indicators and sensors available to the partition at the time of the + call. + + Software Implementation Notes: + + + + + Relative to Requirement + , due to Dynamic + Reconfiguration, the indicators available at any point in time might be + different than on a previous call to + ibm,get-indices. + + + + 9007 indicators may need to be provided to the OS in the order + in which they are best displayed to the user, because the OS or the UI + may not reorder them (for example, sort them) before presenting them to + the user. This is true regardless of the method of presentation to the OS + (OF device tree or + ibm,get-indices RTAS call). Relative to presentation + order, see also Requirement + + + + + + + + R1--3. + + If a platform + provides any 9007 indicators to the OS, then the following must be + true: + + + + The platform must set the location code of each Identify (9007) + indicator and sensor (Enclosure, FRU, or connector) to be the location + code of the enclosure, FRU, or connector to which that indicator is + associated. + + + + The System + Enclosure Identify (9007) indicator must be the first indicator in the + list of 9007 indicators. + + + + For every 9007 indicator, there must be a corresponding 9007 + sensor which has the same index as the corresponding indicator. + + + + + + + R1--4. + + A DR indicator (9002) must only be + provided to an OS if that particular OS image owns that resource and is + going to control the physical add, remove, and replace operations on the + FRU which is pointed to by that particular DR indicator. + + + + + R1--5. + + If a PCI Hot Plug slot implements a single + physical amber indicator for use as both the PCI Hot Plug DR indicator + (for concurrent maintenance) and as the FRU Identify indicator, then that + indicator must be presented to a LoPAR compliant OS as both a 9002 and + 9007 indicator. + + + + + R1--6. + + All platforms must provide the + “ibm,fault-behavior” and + “ibm,fru-9006-deactivate” properties in + the + root node of the OF device tree, both with a value of + 1. + + + + +
+ +
+ + Lightpath User Interface (UI) Requirements + The base Lightpath architecture does not provide a User Interface + (UI), per se, when one considers a UI as being an interactive entity; + that is, where the user can input requests as well as just see the + faults. When enabling the Identify indicators of the Lightpath mode, a UI + is necessary. This architecture will call this the Lightpath UI. The + Lightpath UI is an interface between the Service Focal Point (SFP) and + the user of the SFP, and at a minimum, provides an interface to show + hidden Fault indicators (for example, see + ). A slightly more + sophisticated Lightpath UI -- one with a General UI (GUI) such as an LCD + or general display like provided by IBM Director -- is required to + provide access to the Identify indicators. + Enablement of the Identify portion of Lightpath is important in + larger systems for reasons of deferred maintenance and guided + maintenance. In a system with deferred maintenance and Lightpath, many + Fault indicators may remain lit, requiring directed repair via an + Identify operation in order to see the component against which to do a + particular repair action. In addition, guided maintenance may be required + even if there is no failing component, to indicate to the user where to + plug or un-plug components or cables. + When a Lightpath UI is available, the platform does not display + logical Fault or Error Log on the physical indicators until a user + requests such a display of the indicators, with the exception that the + highest level roll-up indicators will be lit as a flag for the user to + use the Lightpath UI to identify the problem. The request to display + Fault and Error Log indicators may be made, for example, by pressing a + button or series of buttons, or by checking a check-box on a more + sophisticated Lightpath UI. The button(s) may be physical or may be on a + device like an LCD panel or other Service Focal Point (SFP) display, like + an IBM Director display. + + defines an SFP as: + “…common point of control in the system for handling all + service actions which are not resolved otherwise (for example, via Fault + indicators).” SFPs may or may not exist lower end systems, and may + exhibit different levels of sophistication in larger systems. The + following are some (not all) system implementation examples: + + + + For simple systems, there may be no SFP and no Lightpath UI, + which means everything needs to be resolved by Fault indicators. + + + + For simple systems implementing Triple-S (see + ), there may exist a simple SFP + with a simple Lightpath UI like one or more physical push-buttons. This + could be the System Error indicator with a physical button associated + with it, with the SFP being firmware underlying the button to communicate + with lower layers of firmware (for example, turn off FRU Fault indicators + as they are activated by the firmware, turn on all active FRU Faults + indicators on a button press). There may also be buttons for enabling the + lower layers of the Fault indicator hierarchy, and these buttons inform + the SFP firmware of the user’s request to display Fault indicators + on the physical indicators. In this case, the Lightpath UI is not + full-function and does not provide for enablement of the Identify + indicators. In this case, the firmware driving the Lightpath UI would use + the Lightpath UI base enablement (see + ). + + + + For intermediate systems, the Lightpath UI could be an LCD panel. + In this case, the firmware driving the Lightpath UI would use the + Lightpath UI base enablement (see + ). The Triple-S UI is also + possible (see + ). + + + + For larger systems, the Lightpath UI could be part of a more + sophisticated interface, like IBM Director. This more sophisticated + interface would use the Lightpath UI base enablement (see + ). The Triple-S UI is also + possible (see + ). + + + +
+ Lightpath UI Base Enablement Requirements + This section defines the base enablement requirements for all + Lightpath UI implementations. The Triple-S UI is one example of such a + Lightpath UI that uses the Lightpath UI Base Enablement. Other Lightpath + UIs are possible, and are not limited by this architecture. + + + + R1--1. + + For the Lightpath UI Base Enablement: + The platform must do all of the following: + + + + Implement Lightpath Mode, as defined by this architecture, + lighting FRU Fault indicators or Error Log indicator associated with a + fault. Lightpath Mode includes the implementation of Identify + indicators. + + + + If the SFP is + separate from the platform, then report to the SFP that the platform + implements the Lightpath UI Base Enablement (explicitly or implicitly). + (see implementation note, below) + + + + Whenever + possible, report all fault conditions which activate a FRU Fault + indicator or Error Log indicator, up to the SFP, with enough information + to allow determination by the SFP as to which FRU or Error Log indicators + are activated and the possible failing FRU(s). See the implementation + note, below, for the only exception cases allowed to this + requirement. + + + + Accept commands + from the Service Focal Point (SFP) to put each indicator (FRU, Enclosure, + etc.), into the Off, Fault and Identify states (that is, the SFP can + control each indicator), and not report an activation or deactivation + error to the SFP if the SFP requests putting the indicator into a state + to which the indicator is already activated. See the implementation note, + below, for the only exception cases allowed to this requirement. + + + + Prevent multiple + reports of same error, whenever possible. (see implementation note, + below) + + + + + Implementation Notes: + + + + + Requirement + allows a SFP to manage multiple + platforms that implement different Service Indicator modes. Note that + this requirement can be implemented implicitly from other information + reported to the SFP (for example, machine type/model). + + + + In Requirement + and + , acceptable reasons for not + being able to report errors to the SFP or have the SFP control the LEDs + may include: + + + + Loss of communications between the component and the SFP. + + + + A fault indicator that is entirely controlled by an OS, hardware, + or code, or an entity which is not in communications with the platform + firmware or the SFP. + + + + + + Requirement + prevents continual + “blinking” of Fault indicator and the flooding of the + SFP’s event or error log. + + + + + + + R1--2. + + For the Lightpath UI Base Enablement: + The Service Focal + Point (SFP) must exist and must do all of the following: + + + + Receive and log + fault conditions reported by the platform. (see implementation note, + below) + + + + Turn off each + Fault indicator or Error Log indicator associated with a fault condition, + as soon as possible after the fault is reported, except as required to + remain on by user request user request (for example, see Requirement + ). + + + + Accept direction from a user to show any faults on the Fault and + Error Log indicators (for example, see Requirement + ). + + + + If the SFP + contains a GUI (for example, an LCD display or a display like provided by + IBM Director), accept direction from a user to Identify a FRU or + connector for a service operation, and then turn off all activated FRU + Fault and Error Log indicators, unless otherwise directed by the user + (for example, by a check-box on the UI), and activate the FRU Identify + (blink), along with the normal FRU roll-up defined by the base Lightpath + Mode. + + + + + Implementation Notes: + + + + + Relative to Requirements + , a SFP may (but is not + required to) do additional failure analysis, or may apply policy rules, + on the failure(s) reported, and by doing so may change or re-prioritize + the list of failures, such that the most likely failure(s) is (are) + different than the fault indicator(s) that were initially turned on by + the detecting entity. In which case, when the user requests that the + indicators be reactivated, a different set may be activated than those + that were originally activated. + + + + In simpler systems, it is expected that there may only be one + push-button implemented, and that would be associated with the highest + level Fault roll-up indicator. For systems, or collection of systems that + are managed by a SFP, which consist of many enclosures, it may be useful + for an implementation to implement several levels of buttons. For + example, a SFP that manages multiple systems may (at least) implement one + button per system. + + + + + + +
+ +
+ + See/Select/Service (Triple-S) User Interface + Requirements + The Triple-S UI architecture is built on top of the Lightpath UI + Base Enablement architecture, which is in turn built on top of the + Lightpath architecture. The Triple-S architecture is basically defined as + follows (see Requirements for specifics): + + + + Do not display Fault or Error Log on the physical indicators + until user pushes a button or series of buttons. + + + + Except that the highest level roll-up for the Enclosure Fault + indicators and Error Log indicators will be activated if a lower level + one of the same type was activated. + + + + + + After seeing the highest level roll-up for Enclosure Fault or + Error Log being on, the user pushes one or more buttons (logical or + physical) associated with those, and then the user + Sees the Faults available for servicing. + + + + The user + Selects the item they want to service, by observing + the FRU Faults and selecting they want to then Service. + + + + The Selects part of Triple-S may also involve + activation of the FRU Identify indicator from the Lightpath UI. + + + + + + The user completes the Service action on that component which was + selected. + + + + + + + R1--1. + + For the Triple-S UI: The Lightpath UI Base Enablement + requirements must be met, as defined in + . + + + + + R1--2. + + For the Triple-S UI: The platform must provide one or + more push-buttons (physical button, or logical on a GUI), each associated + with a set of Fault indicators or Error Log indicators which is (are) to + be used by the user to display (“show”) or not display + (“hide”) fault conditions on those group of indicators, as + defined by Requirement + . + + + + + R1--3. + + For the Triple-S UI: + The Service Focal + Point (SFP) must accept direction from a user from a push-button + (physical or logical) press to show any fault conditions on, or hide all + fault conditions from, the physical indicators (FRU Faults and any + associated roll-up indicators for those indicators), which are associated + with the push-button (Fault or Error Log indicators). The fault + conditions must represent any open problems known by the SFP related to + the set of indicators associated with the push-button. The push of the + button must be a toggle operation, with each press either going from the + show state to the hide state or from the hide state to the show state, + based on the state prior to the push-button press. The platform must turn + off any indicators turned on by these push-button activations after a + pre-set period of time after the button activation, unless the pre-set + time is set to 0, in which case the indicators are left on until the + button is press again or until the platform determines they are no longer + needed to be on. (see implementation note, below). + + + + + R1--4. + + For the Triple-S UI: For more complex systems, and as + determined by the RAS requirements for those systems, the SFP must + implement a GUI (for example, an LCD or IBM Director display) and provide + the capability to activate the Identify indicators, as defined in + Requirement . + + + Implementation Notes: + + + + + Relative to Requirement + , a SFP may (but is not + required to) do additional failure analysis, or may apply policy rules, + on the failure(s) reported, and by doing so may change or re-prioritize + the list of failures, such that the most likely failure(s) is (are) + different than the fault indicator(s) that were initially turned on by + the detecting entity. In which case, when the user requests that the + indicators be reactivated, a different set may be activated than those + that were originally activated. + + + + Relative to Requirement + , the set of indicators + associated with a given push-button will normally be hierarchical, based + on the FRU Fault or Error Log roll-up path. For example, if a push-button + is associated with the Chassis Enclosure fault indictor, pressing that + button would toggle the show/hide state for all fault indicators within + that Chassis. Another example is pressing of a button associated with the + System Error roll-up indicator for a system, putting that system into the + “show” state could put that system basically into a Lightpath + (without Triple-S) mode, or “Lightpath Classic” mode. In this + latter example, it is not quite like previous implementations of + Lightpath because (1) service procedures may be different, (2) based on + Implementation note (a) the set of FRU Faults activated by the SFP may be + different than those activated by the entity detecting the error + originally, and (3) the Identify function can be used. + + + + + + +
+
+ +
+ +
+ Green Indicator Requirements + This chapter defines the platform requirements for green + indicators. + The usage of green indicators has been separated from the rest of + this chapter, because even though green indicators are used in some service + procedures (for example, to check for presence or absence of power on a + component or system), they are not to be used in lieu of amber FRU Fault + and Identify indicators. That is, they should supplement, not replace, the + amber indicators. + There are several exceptions to having all the green indicator + requirements in this chapter: + + + + The green indicator associated with a capacitor and pushbutton + implementation is specified in Requirement .). + + + + The capability to light all green indicators, as well as the amber + and blue indicators, for test purposes, is specified in Requirement + . + + + + Unless indicated otherwise in this chapter, the blink rate for + green indicators, when they blink, is specified in Requirement + . + + + + +
+ Green Indicator Uses and General Requirements + Green indicators generally are not used for indicating a fault + condition. + + + + R1--1. + + A green indicator must not be used in + place of an amber Fault/Identify indicator, except when use of amber + Fault/Identify indicator is not possible, and in this exceptional case, + the green must be off or blinking to indicate the error condition. + + Implementation Note: Examples where a + green indicator + might be used instead of an amber Fault/Identify indicator are: + + + + In a power supply to indicate lack of AC power (green + off). + + + + In the case where there is insufficient power to power the + component (green blinking). + + + + + + + R1--2. + + There must exist a green power indicator + for every FRU that is to participate in concurrent maintenance + (“hot plug” operation), unless that FRU does not require the + removal of power to remove or insert that FRU. + + + + +
+ +
+ Green Indicator States + This section attempts to capture the state requirements for all + usages of green indicators. If a state or usage is not specified, then + the user needs to get with the Architecture team for this architecture in + order to add or replace any state or usage of that state. + +
+ Power Supply Green Indicators + + + + R1--1. + + For power supply indicators, the + platform must implement the states defined in + for each green indicator, and + must use those states only for the usages stated in + . +   + + Power Supply Green Indicator States and Usage + + + + + + + + + + Green Indicator State + + + + + Usage + + + + + + + + Any not already covered in this table + + + Consult with the xipSIA architecture team for the proper + usage/behavior. + + + + + Off + + + For the input power indicator: no input power. + For the output power indicator: no output power. + + + + + On + + + For the input power indicator: input power good. + For the output power indicator: output power good. + + + + + Slow blink (1 Hz, 50% duty cycle) + + + Power supply (or supplies) are in the standby state. A + power supply must not blink its green output power indicator + unless that particular supply is in the standby state. + + + + +
+ + + + +
+ +
+ System Power Green Indicators + + + + R1--1. + + For system power indicators, the + platform must implement the states defined in + for each green indicator, and + must use those states only for the usages stated in + . +   + + System Power Green Indicator States and Usage + + + + + + + + + + Green Indicator State + + + + + Usage + + + + + + + + Any not already covered in this table + + + Consult with the xipSIA architecture team for the proper + usage/behavior. + + + + + Off + + + System is off (no standby power). + + + + + On + + + System is on (operational state). + + + + + Fast blink (4 Hz, 50% duty cycle) + + + A determination is being made as to whether the system + (for example, a Blade in a Blade System) has enough power + available to it, in order to power up, or a determination has + already been made that there is not enough power, and the + indicator remains in this state. + + + + + Slow blink (1 Hz, 50% duty cycle) + + + System is in the standby power state. + + + + + Fade-in/fade-out cycling of the power LED as done in + various PC and notebook manufacturers: + the period of this fade-in/fade-out cycle is 2 seconds, + gradually ranging from fully on to fully off + + + Systems that support system-level sleep states (such as + the S3 sleep state) must use this state as a way to indicate + the system is sleeping but still powered on. + + + + +
+ + + + +
+ +
+ HDD Green Indicators + + + + R1--1. + + For Hard Disk Drives (HDD) the platform + must implement the states defined in + for each green indicator, and + must use those states only for the usages stated in + . +   + + HDD Green Indicator States and Usage + + + + + + + + + + Green Indicator State + + + + + Usage + + + + + + + + Any not already covered in this table + + + Consult with the xipSIA architecture team for the proper + usage/behavior. + + + + + Off + + + Platform specific. + + + + + On + + + Platform specific. + + + + + Flickering (randomly blinking) + + + HDD activity (HDD is powered on and is being + used). + + + + +
+ + + + +
+ +
+ Other Component/FRU Green Indicators + This section attempts to capture the state requirements for usages + of green indicators that are not specifically called out as special cases + elsewhere in + . To reiterate what was + specified, above: if a state or usage is not specified, then the user + needs to get with the Architecture team for this architecture in order to + add or replace any state or usage of that state. + + + + R1--1. + + For FRUs or components other than + specific ones specified elsewhere in + , which require power + indicators, the platform must implement the states defined in + for each green indicator, and + must use those states only for the usages stated in + . +   + + Sub-Unit (Component) Green Indicator States and + Usage + + + + + + + + + + Green Indicator State + + + + + Usage + + + + + + + + Any not already covered in this table + + + Consult with the xipSIA architecture team for the proper + usage/behavior. + + + + + Off + + + Component/FRU is powered off and/or is not in + operation. + + + + + On + + + Component/FRU is powered on. + + + + + Blink 1 Hz, 50% duty cycle + + + (Optional) Component/FRU is in transition to the off + state. Note that although this is an optional state, it is + highly recommended (for Human Factors reasons) for cases where + it takes awhile to power off the component (for example, for + hardware like a Blade in a Blade System that has to be quiesced + before powering off). + + + + +
+ + + + +
+ +
+ Communication Link Green Indicators + + + + R1--1. + + For communication links, the platform + must implement the states defined in + for each green indicator, and + must use those states only for the usages stated in + . +   + + Communication Link Green Indicator States and + Usage + + + + + + + + + + Green Indicator State + + + + + Usage + + + + + + + + Any not already covered in this table + + + Consult with the xipSIA architecture team for the proper + usage/behavior. + + + + + Off + + + No link connection or link connected but no + activity. + + + + + Flickering (randomly blinking) + + + Communication link activity. + + + + +
+ + + + +
+ +
+ +
+ diff --git a/Error Handling/figures/PAPR-34.gif b/Error Handling/figures/PAPR-34.gif new file mode 100644 index 0000000..737a47d Binary files /dev/null and b/Error Handling/figures/PAPR-34.gif differ diff --git a/Error Handling/figures/PAPR-36.gif b/Error Handling/figures/PAPR-36.gif new file mode 100644 index 0000000..9242a7f Binary files /dev/null and b/Error Handling/figures/PAPR-36.gif differ diff --git a/Error Handling/figures/PAPR-37.gif b/Error Handling/figures/PAPR-37.gif new file mode 100644 index 0000000..b0e249d Binary files /dev/null and b/Error Handling/figures/PAPR-37.gif differ diff --git a/Error Handling/figures/PAPR-38.gif b/Error Handling/figures/PAPR-38.gif new file mode 100644 index 0000000..39af86f Binary files /dev/null and b/Error Handling/figures/PAPR-38.gif differ diff --git a/Error Handling/figures/PAPR-39.gif b/Error Handling/figures/PAPR-39.gif new file mode 100644 index 0000000..81f8f29 Binary files /dev/null and b/Error Handling/figures/PAPR-39.gif differ diff --git a/Error Handling/figures/PAPR-40.gif b/Error Handling/figures/PAPR-40.gif new file mode 100644 index 0000000..e38139b Binary files /dev/null and b/Error Handling/figures/PAPR-40.gif differ diff --git a/Error Handling/figures/PAPR-41.gif b/Error Handling/figures/PAPR-41.gif new file mode 100644 index 0000000..9f941b9 Binary files /dev/null and b/Error Handling/figures/PAPR-41.gif differ diff --git a/Error Handling/figures/PAPR-42.gif b/Error Handling/figures/PAPR-42.gif new file mode 100644 index 0000000..8565d97 Binary files /dev/null and b/Error Handling/figures/PAPR-42.gif differ diff --git a/Error Handling/figures/PAPR-43.gif b/Error Handling/figures/PAPR-43.gif new file mode 100644 index 0000000..2dff056 Binary files /dev/null and b/Error Handling/figures/PAPR-43.gif differ diff --git a/Error Handling/figures/PAPR-44.gif b/Error Handling/figures/PAPR-44.gif new file mode 100644 index 0000000..c2e622a Binary files /dev/null and b/Error Handling/figures/PAPR-44.gif differ diff --git a/Error Handling/figures/PAPR-45.gif b/Error Handling/figures/PAPR-45.gif new file mode 100644 index 0000000..189ae21 Binary files /dev/null and b/Error Handling/figures/PAPR-45.gif differ diff --git a/Error Handling/figures/PAPR-46.gif b/Error Handling/figures/PAPR-46.gif new file mode 100644 index 0000000..d988e67 Binary files /dev/null and b/Error Handling/figures/PAPR-46.gif differ diff --git a/Error Handling/figures/PAPR-47.gif b/Error Handling/figures/PAPR-47.gif new file mode 100644 index 0000000..f110637 Binary files /dev/null and b/Error Handling/figures/PAPR-47.gif differ diff --git a/Error Handling/figures/PAPR-48.gif b/Error Handling/figures/PAPR-48.gif new file mode 100644 index 0000000..917b1ec Binary files /dev/null and b/Error Handling/figures/PAPR-48.gif differ diff --git a/Error Handling/figures/PAPR-49.gif b/Error Handling/figures/PAPR-49.gif new file mode 100644 index 0000000..1e218f3 Binary files /dev/null and b/Error Handling/figures/PAPR-49.gif differ diff --git a/Error Handling/figures/PAPR-50.gif b/Error Handling/figures/PAPR-50.gif new file mode 100644 index 0000000..291e8f3 Binary files /dev/null and b/Error Handling/figures/PAPR-50.gif differ diff --git a/Error Handling/figures/PAPR-51.gif b/Error Handling/figures/PAPR-51.gif new file mode 100644 index 0000000..b4ddd2f Binary files /dev/null and b/Error Handling/figures/PAPR-51.gif differ diff --git a/Error Handling/figures/PAPR-52.gif b/Error Handling/figures/PAPR-52.gif new file mode 100644 index 0000000..04251e6 Binary files /dev/null and b/Error Handling/figures/PAPR-52.gif differ diff --git a/Error Handling/figures/PAPR-53.gif b/Error Handling/figures/PAPR-53.gif new file mode 100644 index 0000000..f62cf5e Binary files /dev/null and b/Error Handling/figures/PAPR-53.gif differ diff --git a/Error Handling/figures/PAPR-54.gif b/Error Handling/figures/PAPR-54.gif new file mode 100644 index 0000000..b863c9e Binary files /dev/null and b/Error Handling/figures/PAPR-54.gif differ diff --git a/Error Handling/figures/PAPR-73.gif b/Error Handling/figures/PAPR-73.gif new file mode 100644 index 0000000..be0d7a5 Binary files /dev/null and b/Error Handling/figures/PAPR-73.gif differ diff --git a/Error Handling/pom.xml b/Error Handling/pom.xml new file mode 100644 index 0000000..d20e88d --- /dev/null +++ b/Error Handling/pom.xml @@ -0,0 +1,148 @@ + + + + + org.openpowerfoundation.docs + workgroup-pom + 1.0.0-SNAPSHOT + ../pom.xml + + 4.0.0 + + + LoPAR-Error + + jar + + + LoPAR-Error + + + + + 0 + + + + + + + + + org.openpowerfoundation.docs + + openpowerdocs-maven-plugin + + + + generate-webhelp + + generate-webhelp + + generate-sources + + + ${comments.enabled} + LoPAR-Error + 1 + UA-17511903-1 + + appendix toc,title + article/appendix nop + article toc,title + book toc,title,figure,table,example,equation + book/appendix nop + book/chapter nop + chapter toc,title + chapter/section nop + section toc + part toc,title + qandadiv toc + qandaset toc + reference toc,title + set toc,title + + + 1 + 3 + 1 + + + LoPAR_Error_Handling + + + LoPAR_Error_Handling + + + + workgroupSpecification + + + + + workgroupConfidential + + + + + draft + + + + + + + + + true + . + + + bk_main.xml + + + + + ${basedir}/../glossary/glossary-terms.xml + 1 + www.openpowerfoundation.org + + + + + + diff --git a/Error Handling/sec_error_introduction.xml b/Error Handling/sec_error_introduction.xml new file mode 100644 index 0000000..20fdebb --- /dev/null +++ b/Error Handling/sec_error_introduction.xml @@ -0,0 +1,85 @@ + + +
+ + Introduction + + RTAS provides a mechanism which helps OSs avoid the need for + platform-dependent code that checks for, or recovers from, errors or + exceptional conditions. The mechanism is used to return information about + hardware errors which have occurred as well as information about non-error + events, such as environmental conditions (for example, temperature or + voltage out-of-bounds) which may need OS attention. This permits RTAS to + pass hardware event information to the OS in a way which is abstracted from + the platform hardware. This mechanism primarily presents itself to the OS + via two RTAS functions, + event-scan and + check-exception, which are described further in + . A further RTAS function, + rtas-last-error, is also provided to return + information about hardware failures detected specifically within an RTAS + call. + + The + event-scan function is called periodically to check for + the presence or past occurrence of a hardware event, such as a soft failure + or voltage condition, which did not cause a program exception or interrupt + (for example, an ECC error detected and corrected by background scrubbing + activity). The + check-exception function is called to provide further + detail on what platform event has occurred when certain exceptions or + interrupts are signaled. The events reported by these two functions are + mutually exclusive on any given platform; that is, a platform may choose to + notify the OS of a particular event type either through + event-scan or through an interrupt and + check-exception, but not both. + + Since firmware is platform-specific, it can examine hardware + registers, can often diagnose many kinds of hardware errors down to a root + cause, and may even perform some very limited kinds of error recovery on + behalf of the OS. The reporting format, described in this chapter, permits + firmware to report the type of error which has occurred, what entities in + the platform were involved in the error, and whether firmware has + successfully recovered from the error without the need for further OS + involvement. Firmware may not, in many cases, be able to determine all the + details of an error, so there are also returned values which indicate this + fact. Firmware may optionally provide extended error diagnostic + information, as described in + . + + The abstractions provided by this architecture enable the handling of + most platform errors and events without integrating platform-specific code + into each supported OS. + + Architecture Note: It is not a goal of the firmware to diagnose all + hardware failures. Most I/O device failures, for example, will be detected + and recovered by an associated device driver. Firmware attempts to + determine the cause of a problem and report what it finds, to aid the end + user (by providing meaningful diagnostic data for messages) and to prevent + the loss of error syndrome information. Firmware is never required to + correct any problem, but in some cases may attempt to do so. System vendors + who want more extensive error diagnosis may create OS error handlers which + contain specific hardware knowledge, or could use firmware to collect a + minimum set of error information which could then be used by diagnostics to + further analyze the cause of the error. + +
diff --git a/Error Handling/sec_error_reporting.xml b/Error Handling/sec_error_reporting.xml new file mode 100644 index 0000000..837388c --- /dev/null +++ b/Error Handling/sec_error_reporting.xml @@ -0,0 +1,87 @@ + + +
+ + Error and Event Reporting + + The error and event reporting RTAS calls are designed to provide an + abstract interface into hardware registers in the system that may contain + correctable or non-correctable errors and to provide an abstract interface + to certain platform events that may be of interest to the OS. Such errors + and events may be detected either by a periodic scan or by an exception trap. + + + These functions are not intended to replace the normal error handling + in the OS. Rather, they enhance the OS’s abilities by providing an + abstract interface to check for, report, and recover from errors or events + on the platform that are not necessarily known to the OS. + + The OS uses the error and event RTAS calls in two distinct ways: + + + + + Periodically, the OS calls event-scan + to have + the system firmware check for any errors or events that have occurred. + + + + + Whenever the OS receives an interrupt or exception that it cannot + fully process, it calls check-exception. + + + + + The first case covers all errors and events that do not signal their + occurrence with an interrupt or exception. The second case covers those + errors and events that do signal with an interrupt or exception. It is + platform dependent whether any specific error or event causes an interrupt + on that platform. + + + + + R1--1. + + RTAS must return the event generated by a + particular interrupt or event source by either + check-exception or event-scan, + but not both. + + + + + R1--2. + + check-exception + and event-scan , on a 64-bit capable platform, must + be able to handle platform resources that are accessed using 64-bit + addresses when instantiated in 32-bit mode. + + + + +
diff --git a/Error Handling/sec_rtas_env_epow.xml b/Error Handling/sec_rtas_env_epow.xml new file mode 100644 index 0000000..52237f2 --- /dev/null +++ b/Error Handling/sec_rtas_env_epow.xml @@ -0,0 +1,336 @@ + + +
+ + Environmental and Power Warnings + + Environmental and Power Warnings (EPOW) is an option that provides + a means for the platform to inform the OS of these types of events. The + intent is to enable the OS to provide basic information to the user about + environmental and power problems and to minimize the logical damage done + by these problems. For example, an OS might want to abort all disk I/O + operations in progress to ensure that disk sectors are not corrupted by + the loss of power. Even on platforms that provide hardware protection of + data during environmental events, EPOW notification allows discrimination + between I/O errors caused by hardware failures versus EPOW events. + + These warnings include action codes that the platform can use to + influence the OS behavior when various hardware components fail. For + example, a fan failure where the system can continue to operate in the + safe cooling range may just generate an action code of WARN_COOLING, but + a fan failure where the system cannot operate in the safe cooling range + may generate an action code of SYSTEM_HALT. + + Implementation Note: Hardware cannot assume that the OS will + process or take action on these warnings. These warnings are only + provided to the OS in order to allow the OS a chance to cleanly abort + operations in progress at the time of the warning. Hardware still assumes + responsibility for preventing hardware damage due to environmental or + power problems. + + An OS that wants to be EPOW-aware will look for the + epow-events node in the OF device tree, enable the + interrupts listed in its + “interrupts” property, and provide an + interrupt handler to call + check-exception when one of those interrupts are + received. + + When an EPOW event occurs, whether reported by + check-exception or + event-scan, RTAS will directly pass back the EPOW + sensor value as part of the Extended Error Log format as described in + , assuming the extended log is + requested. Doing so avoids the need for the OS to make an extra RTAS call + to obtain the sensor value. For critical power problems, the + check-exception function is used to immediately + report changes of state to the OS, while the + get-sensor-state function allows the OS to monitor + the condition (for example, loss of AC power) to see if the problem + corrects itself. + + + + + R1--1. + + If the platform supports Environmental and + Power Warnings by including a EPOW device tree entry, then the platform + must support the EPOW sensor for the + get-sensor-state RTAS function. + + + + + R1--2. + + The EPOW sensor, if provided, must contain + the EPOW action code (defined in + ) in the least significant 4 + bits. In cases where multiple EPOW actions are required, the action code + with the highest numerical value (where 0 is lowest and 7 is highest) + must be presented to the OS. The platform may implement any subset of + these action codes, but must operate as described in + for those it does implement. + + + + + R1--3. + + To ensure adequate response time, + platforms which implement the EPOW_MAIN_ENCLOSURE or EPOW_POWER_OFF + action codes must do so via interrupt and + check-exception notification, rather than by + event-scan notification. + (Except as modified by Requirement + ) + + + + + R1--4. + + If the platform + does not notify EPOW_MAIN_ENCLOSURE or EPOW_POWER_OFF via interrupt, then + the platform must protect data on I/O storage devices from corruption due + to the EPOW event. + + + + + R1--5. + + For interrupt-driven EPOW events, the + platform must ensure that an EPOW interrupt is not lost in the case where + a numerically higher-priority EPOW event occurs between the time when + check-exception gathers the sensor value and when it + resets the interrupt. + + + + + R1--6. + + For SYSTEM_SHUTDOWN EPOW class 3, after a + SYSTEM_SHUTDOWN EPOW commences and when the delay interval timer expires, + if an + “ibm,recoverable-epow3” + encode-null + property in the + /rtas node is present, then the OS code that manages + preserving storage must check the EPOW sensor state and the + “ibm,request-partition-shutdown” + property if present. A normal boot must only occur when the EPOW sensor state + indicates that the EPOW condition requiring a shutdown no longer exists + (EPOW 0) and the + “ibm,request-partition-shutdown” + is not present. Otherwise, the code that manages preserving storage must take + the action as identified by the property. + + + + + + Implementation Note: One way for hardware to prevent the loss of an + EPOW interrupt is by deferring the generation of a new EPOW interrupt + until the existing EPOW interrupt is reset by a call to the RTAS + check-exception function. Another way is to ignore + resets to the interrupt until all EPOW events have been reported. + + + EPOW Action Codes + + + + + + + + + Action Code + + + + + Value + + + + + Description + + + + + + + + EPOW_RESET/MESSAGE + + + 0 + + + No EPOW event is pending. This action code is the lowest + priority. + + + + + WARN_COOLING + + + 1 + + + A non-critical cooling problem exists. An EPOW-aware OS + logs the EPOW information. + + + + + WARN_POWER + + + 2 + + + A non-critical power problem exists. An EPOW-aware OS + logs the EPOW information. + + + + + SYSTEM_SHUTDOWN + + + 3 + + + The system must be shut down. An EPOW-aware OS logs the + EPOW error log information, then schedules the system to be + shut down to begin after an OS defined delay internal (default + is 10 minutes.) + + + + + SYSTEM_HALT + + + 4 + + + The system must be shut down quickly. An EPOW-aware OS + logs the EPOW error log information, then schedules the system + to be shut down in 20 seconds. + + + + + EPOW_MAIN_ENCLOSURE + + + 5 + + + The system may lose power. The hardware ensures that at + least 4 milliseconds of power within operational thresholds is + available after signalling an interrupt. An EPOW-aware OS + performs any desired functions, masks the EPOW interrupt, and + monitors the sensor to see if the condition changes. Hardware + does not clear this action code until the system resumes + operation within safe power levels. + + + + + EPOW_POWER_OFF + + + 7 + + + The system will lose power. The hardware ensures that at + least 4 milliseconds of power within operational thresholds is + available after signalling an interrupt. An EPOW-aware OS + performs any desired operations, then attempts to turn system + power off. An EPOW-aware OS does not clear the EPOW interrupt + for this action code. This action code is the highest + priority. + + + + +
+ + Software Implementation Note: A recommended OS processing method + for an EPOW_MAIN_ENCLOSURE event is as follows: + + + + + Prepare for shutdown, mask the EPOW interrupt, and wait for 50 + milliseconds. Then call get-sensor-state to read the EPOW sensor. + + + + + If the EPOW action code is unchanged, wait an additional 50 + milliseconds. + + + + + If the action code is EPOW_POWER_OFF, attempt to power off. + Otherwise, the power condition may have stabilized, so interrupts may be + enabled and normal operation resumed. + + + + + + Implementation Note: EPOW_RESET (EPOW action code 0) + may be used to indicate that a previously reported EPOW condition is no + longer present. For instance, a system might see a WARN_POWER action code + for a loss of a redundant line input power. EPOW_RESET may subsequently + be issued if the line power were restored. The same bits in the EPOW + error log that specified the type of WARN_POWER EPOW generated would be + set in the EPOW_RESET error log to indicate the specific EPOW event that + was reset. + + Systems that do not support an EPOW interrupt would generally be + unable to support the EPOW action codes 5 and 7. In those cases, there + could not be an EPOW event to indicate a loss of power. However, after + power were restored, generating the EPOW_RESET EPOW would indicate that + the system had lost power previously and the power had been restored. The + EPOW_RESET should only be used in this way if the system is unable to + generate an EPOW class 5 or class 7. + +
diff --git a/Error Handling/sec_rtas_error_indications.xml b/Error Handling/sec_rtas_error_indications.xml new file mode 100644 index 0000000..4a51bd4 --- /dev/null +++ b/Error Handling/sec_rtas_error_indications.xml @@ -0,0 +1,711 @@ + + +
+ + Internal Error Indications + + Hardware may detect a variety of problems during operation, ranging + from soft errors which have already been corrected by the time they are + reported, to hard errors of such severity that the OS (and perhaps the + hardware) cannot meaningfully continue operation. The mechanisms + described in + are used to report such errors to the + OS. This section describes the architectural sources of errors, and + describes a method that platforms can use to report the error. All OSs + need to be prepared to encounter the errors reported as they are + described here. However, in some platforms more sophisticated handling + may be introduced via RTAS, and the OS may not have to handle the error + directly. More robust error detection, reporting, and correcting are at + the option of the hardware vendor. + + + + The + primary architectural mechanism for indicating hardware errors to an OS + is the machine check interrupt. If an error condition is surfaced by + placing the system in checkstop, it precludes any immediate participation + by the OS in handling the error (that is, no error capture, logging, + recovery, analysis, or notification by the OS). For this reason, the + machine check interrupt is preferred over going to the checkstop state. + However, checkstop may be necessary in certain situations where further + processing represents an exposure to loss of data integrity. To better + handle such cases, a special hardware mechanism may be provided to gather + and store residual error data, to be analyzed when the system goes + through a subsequent successful reboot. + + Less critical internal errors may also be signaled to the OS + through a platform-specific interrupt in the “Internal + Errors” class, or by periodic polling with the + event-scan RTAS function. + + Architecture Note: The machine check interrupt will not be listed + in the OF node for the “Internal Errors” class, since it is a + standard architectural mechanism. The machine check interrupt mechanism + is enabled from software or firmware by setting the MSRME bit =1. Upon + the occurrence of a machine check interrupt, bits in SRR1 will indicate + the source of the interrupt and SRR0 will contain the address of the next + instruction that would have been executed if the interrupt had not + occurred. Depending on where the error is detected, the machine check + interrupt may be surfaced from within the processor, via logical + connection to the processor machine check interrupt pin, or via a system + bus error indicator (for example, Transfer Error Acknowledge - + TEA). + + + + + R1--1. + + OSs must set + MSRME=1 prior to the occurrence of a machine check interrupt in order to + enable machine check processing via the + check-exception RTAS function. + + + Architecture Note: Requirement + is not applicable when the FWNMI + option is used. + + + + + + R1--2. + + For + hardware-detected errors, platforms must generate error indications as + described in + , unless the error can be handled + through a less severe platform-specific interrupt, or the nature of the + error forces a checkstop condition. + + + + + R1--3. + + Platforms which detect and report the + errors described in + must provide information to the OS + via the RTAS + check-exception function, using the reporting format + described in + . + + + + + R1--4. + + To prevent error + propagation and allow for synchronization of error handling, all + processors in a multi-processor system must receive any machine check + interrupt signaled via the external machine check interrupt pin. + + + + + + + Platform Implementation Notes: + + + + + + The intent of Requirement + is to define standard error + notification mechanisms for different hardware error types. For most + hardware errors, the signaling mechanism is the machine check interrupt, + although this requirement hints at the use of a less severe + platform-specific interrupt for some errors. The important point here is + actually whether the error can be handled through that interrupt. Simply + using an external interrupt to signal the error is not sufficient. The + hardware and RTAS also need to limit the propagation of corrupted data, + prevent loss of error state data, and support the cleanup and recovery of + such an error. Since the response to an external interrupt may be + significantly slower than a machine check, and in fact may be masked, the + error should not require immediate action on the part of the OS and/or + RTAS. In addition, external interrupts (except external machine check + interrupts) are reported to only one processor, so operations by the + other processors in an MP system should not be impacted by this error + unless they specifically try to access the failing hardware element. To + summarize, platforms should not use platform-specific interrupts to + signal hardware errors unless there is a complete hardware/RTAS platform + solution for handling such errors. + + + + + The intent of Requirement + is that most hardware errors would be + signaled simultaneously to all processors, so that processors could + synchronize the error handling process; that is, one processor would be + chosen to do the call to + check-exception, while the other processors remained + idle so that they would not interfere with RTAS while it gathered machine + check error data. While this is a straightforward wiring solution for + errors signaled via the external machine check interrupt pin, that is not + the case for internal processor errors or processor bus errors. + Typically, only one processor will see such errors. An internal processor + error can be identified with just the contents of SRR1, and so can be + handled without synchronization with other processors. Processor bus + errors, however, can be more difficult, especially if the error is + propagated up to the processor bus from a lower-level bus. In general, + such propagation should be avoided, and such errors should be signaled + through the machine check interrupt pin to ensure proper error + handling. + + + + +
+ Error Indication Mechanisms + + + describes the mechanisms by + which software will be notified of the occurrence of operational failures + during the types of data transfer operations listed below. The assumption + here is that the error notification can occur only if a hardware + mechanism for error detection (for example, a parity checker) is present. + In cases where there is no specific error detection mechanism, the + resulting condition, and whether the software will eventually recognize + that condition as a failure, is undefined. +   + + Error Indications for System Operations + + + + + + + + + + + + Initiator + + + + + Target + + + + + Operation + + + + + Error Type(if detected) + + + + + Indication to Software + + + + + Comments + + + + + + + + Processor + + + N/A + + + Internal + + + Various + + + Machine check + + + Some may cause checkstop + + + + + Processor + + + Memory + + + Load + + + Invalid address + + + Machine check + + +   + + + + + System bus time-out + + + Machine check + + +   + + + + + Address parity on system bus + + + Machine check + + +   + + + + + Data parity on system bus + + + Machine check + + +   + + + + + Memory parity or uncorrectable ECC + + + Machine check + + +   + + + + + Store + + + Invalid address + + + Machine check + + +   + + + + + System bus time-out + + + Machine check + + +   + + + + + Address parity on system bus + + + Machine check + + +   + + + + + Data parity on system bus + + + Machine check + + +   + + + + + External cache load + + + Memory parity or uncorrectable ECC + + + Machine check + + + Associated with Instruction Fetch or Data Load + + + + + External cache flush + + + Cache parity or + uncorrectable ECC + + + Machine check + + +   + + + + + External cache access + + + Cache parity or + uncorrectable ECC + + + Machine check + + + Associated with Instruction Fetch or Data Transfer + + + + + Processor + + + I/O + + + Load or Store + + + Various errors between the processor and the I/O + fabric + + + Machine check + + + I/O fabrics include hubs and bridges and interconnecting + buses or links. + + + + + Processor + + + I/O bus configuration space + + + Read + + + Various, except no response from IOA + + + Firmware receives a machine check, OS receives + all=1’s data along with a + Status of -1 from the RTAS call + + + If EEH is implemented and enabled, firmware does not get + a machine check and the PE is in the EEH Stopped State on + return from the RTAS call + + + + + No response from an IOA + + + All-1’s data returned, along with a + “Success” + Status from the RTAS call + + + If EEH is implemented and enabled, the PE is not in the + EEH Stopped State on return from the RTAS call + + + + + Write + + + Various, except no response from IOA + + + Firmware receives a machine check, OS receives a + Status of -1 from the RTAS call + + + If EEH is implemented and enabled, firmware does not get + a machine check and the PE is in the EEH Stopped State on + return from the RTAS call + + + + + No response from an IOA + + + Operation ignored, OS receives a “Success” + Status from the RTAS call + + + If EEH is implemented and enabled, the PE is in the EEH + Stopped State on return from the RTAS call + + + + + Processor + + + I/O bus; + I/O Space + or + Memory Space + + + Load + + + Various, except no response from IOA + + + Machine check + + + If EEH is implemented and enabled, no machine check is + received, all-1’s data is returned, and the PE enters the + EEH Stopped State + + + + + No response from an IOA + + + All-1’s data returned + + + Invalid address, broken IOA, or configuration cycle to + non-existent IOA; if EEH is implemented and enabled, the PE + enters the EEH Stopped State + + + + + Store + + + Various, except no response from IOA + + + Machine check + + + If EEH is implemented and enabled, no machine check is + received and the PE enters the EEH Stopped State + + + + + No response from IOA + + + Ignore Store + + + Invalid address, broken IOA, or configuration cycle to + non-existent IOA; if EEH is implemented and enabled, the PE + enters the EEH Stopped State + + + + + Processor + + + Invalid address (addressing an “undefined” + address area) + + + Load or Store + + + No response from system + + + Machine check + + +   + + + + + I/O + + + Memory + + + DMA - either direction + + + Various, including but not limited to: + + + + Invalid addr accepted by a bridge + + + + TCE extent + + + + TCE Page Mapping and Control mis-match or invalid + TCE + + + + + + Machine check unless reportable directly to the IOA in a + way that allows the IOA to signal the error to its device + driver + + + If EEH is implemented and enabled, no machine check is + received and the PE enters the EEH Stopped State + + + + + I/O + + + I/O + + + DMA - either direction + + + Various + + + Machine check unless reportable to master of the transfer + in a way that allows master to recover + + +   + + + + + I/O + + + Invalid address + + + DMA - either direction + + + No response from any IOA + + + PCI IOA + master-aborts + + + Signal device driver using an external interrupt + + + + + PCI IOA + + + - + + + Any + + + Internal, indicated by SERR# or ERR_FATAL + + + SERR# or ERR_FATAL, causing machine check + + + If EEH is implemented and enabled, no machine check is + received and the PE enters the EEH Stopped State + + + + +
+ + Implementation Note: IOAs should, whenever possible, detect the + occurrence of PCI errors on DMA and report them via an external interrupt + (for possible device driver recovery) or retry the operation. Since + system state has not been lost, reporting these errors via a machine + check to the CPUs is inappropriate. Some devices or device drivers may + cause a catastrophic error. Systems which wish to recover from these + types of errors should choose devices and device drivers which are + designed to handle them correctly. + +
+ +
diff --git a/Error Handling/sec_rtas_error_reporting_introduction.xml b/Error Handling/sec_rtas_error_reporting_introduction.xml new file mode 100644 index 0000000..5aa7600 --- /dev/null +++ b/Error Handling/sec_rtas_error_reporting_introduction.xml @@ -0,0 +1,40 @@ + + +
+ + Introduction + + This section describes the data formats used to report events and + errors from RTAS to the OS. A common format is used for errors and events + to simplify software both in RTAS and in the OS. Both errors and events + may have been analyzed to some degree by RTAS, and value judgments may + have been applied to decide how serious an error is, or even how to + describe it to the OS. These judgments are made by platform providers, + since only they know enough about the hardware to decide how serious a + problem it is, whether and how to recover from it, and how to map it onto + the abstracted set of events and errors that a system is required to know + about. There will be cases with some platforms where no reasonable + mapping exists, and platform features may not be fully supported by the + OS. In such cases, error reports may also be non-specific, leaving + platform-specific details to platform-aware software. + +
\ No newline at end of file diff --git a/Error Handling/sec_rtas_error_reporting_location_codes.xml b/Error Handling/sec_rtas_error_reporting_location_codes.xml new file mode 100644 index 0000000..36bddfd --- /dev/null +++ b/Error Handling/sec_rtas_error_reporting_location_codes.xml @@ -0,0 +1,37 @@ + + +
+ + Location Codes + + This document defines an architecture extension for physical + location codes. One use of location codes is to append failing location + information to error logs returned by the + event-scan and + check-exception RTAS services. Refer to + for more information on the + format and use of location codes. For event logs with Version 6 or later, + the location code of FRU call out is contained in the Primary SRC + section, FRU call out sub-section of the Platform Event Log + format. + +
diff --git a/Error Handling/sec_rtas_error_reporting_return_format.xml b/Error Handling/sec_rtas_error_reporting_return_format.xml new file mode 100644 index 0000000..d6819e0 --- /dev/null +++ b/Error Handling/sec_rtas_error_reporting_return_format.xml @@ -0,0 +1,4055 @@ + + +
+ + RTAS Error/Event Return Format + + This section describes in detail the return value retrieved by an + RTAS call to either the + event-scan or + check-exception function. + + The return value consists of a fixed part and an optional Extended + Error Report, described in the next section, which contains full details + of the error. The fixed part is intended to allow reporting the most + common problems in a simple way, which makes error detection and recovery + simple for OSs that want to implement a very simple error handling + strategy. At the same time, the mechanism is capable of providing full + disclosure of the error syndrome information for OSs which have a more + complete error handling strategy. + + RTAS can return at most one return code per invocation. If multiple + conditions exist, RTAS returns them in descending order of severity on + successive calls. + +
+ Reporting and Recovery Philosophy, and Description of + Fields + + All firmware implementations use a common error and event reporting + scheme, as described in detail below. It is not required that error + recovery be present in firmware implementations, nor is it required that + a high degree of error recovery or survival be undertaken by OSs. If such + behavior is desired, then specific platform-dependent handlers can be + loaded into the OS. However, this section defines return result codes and + a philosophy which can be used if aggressive error handling is + implemented in firmware. This section describes the fields of the Error + Report format, and the philosophy which should be applied in generating + return values from firmware or interpreting such return codes in an + OS. + + In general, an OS would look at the Disposition field first to see + if an error has been corrected already by firmware. If not corrected to + the OS’s satisfaction, the OS would examine the Severity field. + Based on that value, and optionally on any information it can use from + the Type and other fields, the OS will make a determination of whether to + continue or to halt operations. In either case, it may choose to log + information regarding the error, using the remaining fields and optional + Extended Error Log. + + The following sections describe the field values in + . + +
+ Version + + This field is used only to distinguish among present and potential + future formats for the remainder of the error report. This value will be + incremented if extensions are made to the format described here. The + primary function of this field is for future OSs to identify whether an + error report may contain some (unknown at present) feature that was added + after the initial version of this specification. + +
+ +
+ Severity + + This field represents the value judgment of firmware of how serious + the problem being reported should be considered by the OS. + + Errors which are believed to represent a permanent hardware failure + affecting the entire system are considered “FATAL.” OSs would + not attempt to continue normal operation after receiving notice of such + an error. OSs may not even be able to perform an orderly shutdown in the + presence of a Fatal error, though they may make a policy decision to + try. + + Less serious errors, but still causing a loss of data or state, are + considered “ERRORs.” In general, continuing after such an + error is questionable, since details of what has failed may not be + available, or if available, may not map nicely onto any ongoing activity + with which the OS can associate it. However, OSs may make a policy + decision (for example, based on the error Type, the Initiator, or the + Target) to continue operation after an Error. + + There are some types of errors, such as parity errors in memory or + a parity error on a transfer between CPU and memory, which occur + synchronously with the current process execution context. Such errors are + sometimes fatal only to the current thread of execution; that is, they + affect only the current CPU state and possibly that of any memory + locations being currently referenced. If that context of execution is not + essential to the system’s operation (for example, if an error trap + mechanism is available in the OS and can be triggered to recover the OS + to a known state), recovery and continuation may be possible. Or at + least, since the memory of the machine is in an undamaged state, the + system may be able to be brought down in an orderly fashion. Such errors + are reported as having Severity “ERROR_SYNC”. It is OS + dependent whether recovery is possible after such an error, or whether + the OS will treat it as a fatal problem. + + The “WARNING” return value indicates that a + non-state-losing error, either fully recovered by firmware or not needing + recovery, has occurred. No OS action is required, and full operation is + expected to continue unhindered by the error. Examples include corrected + ECC errors or bus transfer failures which were re-tried + successfully. + + The “EVENT” return value is the mechanism firmware uses + to communicate event information to the OS. The event may have been + detected by polling using + event-scan or on the occurrence of an interrupt by + calling + check-exception. In either case, the Error Return + value indicates the event which has occurred in the Type field. See the + Type description below for a description of specific events and their + expected handling. + + The “NO_ERROR” return value indicates that no error was + present. In this case, the remainder of the Error Return fields are not + valid and should not be referenced. + +
+ +
+ RTAS Disposition + + An aggressive firmware implementation may choose to attempt + recovery for some classes of error so an OS can continue operation in the + face of recoverable errors. If firmware detects an error for which it has + recovery code, it attempts such action before it returns a value to the + OS (that is, the mechanisms are linked in RTAS and cannot be separately + accessed). Note that Disposition is nearly independent from Severity. + Severity says how serious an error was, and Disposition says, regardless + of severity, whether or not the OS has to even look at it. In general, an + OS will first examine Disposition, then Severity. + + A return value of “FULLY RECOVERED” means that RTAS was + able to completely recover the machine state after the error, and OS + operation can continue unhindered. The severity of the problem in this + case is irrelevant, though for consistency a “FATAL” error + can never be “FULLY RECOVERED.” + + A return value of “LIMITED RECOVERY” means that RTAS + was able to recover the state of the machine, but that some feature of + the machine has been disabled or lost (for example, error checking), or + performance may suffer (for example, a failing cache has been disabled). + The RTAS implementation may return further information in the extended + error log format regarding what action was done or what corrective action + failed. In general, a conservative OS will treat this return the same as + “NOT RECOVERED,” and initiate shutdown. A less conservative + OS may choose to let the user decide whether to continue or to shut + down. + + A value of “NOT RECOVERED” indicates that the RTAS + either did not attempt recovery, or that it attempted recovery but was + unsuccessful. + +
+ +
+ Optional Part Presence + + This is a single flag, valid only if the 32-bit Error Return value + is located in memory, which indicates whether or not an Extended Error + Log Length field and the Extended Error Log follows it in memory. It will + be set on an in-memory return result from RTAS if and only if the RTAS + call indicated sufficient space to return the Extended Error Log, and the + RTAS implementation supports the Extended Error Log. + +
+ +
+ Initiator + + This field indicates, to the best ability of RTAS to determine it, + the initiator of a failed transaction. (Note that in the + “Initiator” field of + , the value “I/O” + indicates one of the defined I/O buses or IOAs. This field contains + finer-grained details of which type of I/O bus failed, if known, and + “UNKNOWN” if RTAS cannot tell.) + + In many of the newer LoPAR platforms, the platform error + notification and handling flow is asynchronous to the OS and software + execution flow, therefore the context of Initiator is not applicable to + the platform firmware. In those cases, the value of “(0) Unknown or + Not Applicable” is used for Initiator. In logs created with Version + 6 or later, more detailed information about the error is provided in the + Platform Event log format. + +
+ +
+ Target + + If RTAS can determine it, this field indicates the target of a + failed transaction. + + In many of the newer LoPAR platforms, the platform error + notification and handling flow is asynchronous to the OS and software + execution flow, therefore the context of Target is not applicable to the + platform firmware. In those cases, the value of “(0) Unknown or Not + Applicable” is used for Target. In logs created with Version 6 or + later, more detailed information about the error are provided in the + Platform Event log format. + +
+ +
+ Type + + This field identifies the general type of the error or event. In + some cases (for example, INTERN_DEV_FAIL), multiple possible events are + grouped together under a common return value. In such cases, + platform-aware software may use the Extended Error Log to distinguish + them. Non-platform-aware software will generally treat all errors of a + given type the same, so it generally will not need to access the Extended + Error Log information. + + In the table, the EPOW values are associated with a Severity of + EVENT. All other values will be associated with Severity values of FATAL, + ERROR, ERROR_SYNC, or WARNING, and may or may not be corrected by + RTAS. + + EPOW is an event type which indicates the potential loss of power + or environmental conditions outside the limits of safe operation of the + platform. See + for more information. + + The “Platform Error (224)”, introduced for Version 6, + generalizes that the error is identified by the platform and the specific + details are encoded in the Platform Event log format itself. + The “ibm,io-events (225)” defines a set of event + notifications which requires special handling by the OS. For this type of + event notification, the Platform Event Log contains the “IO + Events” section which identifies additional details associated with + the event. + + The “Platform information event (226)” indicates the + return log should be logged as “Information Log”. These logs + indicate key platform events and can be used for reference + purposes. + + The “Resource deallocation event (227)” indicates an + event notification to the OS that a specific hardware resource has + experienced recurring recoverable errors with a trend toward + unrecoverable. The OS should take action to deallocate the resource from + usage to prevent unrecoverable errors. For these types of event + notification, the Platform Event Log contains the “Logical Resource + Identification” section which identifies the “Logical + Entity” by Resource Type and Resource ID, associated with the + event. + + The “Dump notification event (228)” indicates that a + dump file is present in the platform and is available for retrieval by + the OS. For this type of event notification, the Platform Event Log + contains the “Dump Locator” section which contains additional + event specific information. + + Additional Type values will be added in future revisions of the + specification. If an OS does not recognize a particular event type, it + can examine the severity first, and then choose to ignore the event if it + is not serious. + +
+ +
+ Extended Event Log Length / Change Scope + + This optional 32-bit field is present in memory following the + 32-bit Event Return value if the Optional Part Presence flag is + “PRESENT”, and it indicates the length in bytes of the + Extended Event Log information which immediately follows it in memory. + The length does not include this field or the Event Return field, so it + may be zero. The field is also present for a resource change “Hot + Plug” event, such as a PRRN event, and then represents the scope of + a resource change. + +
+ +
+ RTAS Event Return Format Fixed Part + + The summary portion of the error return is designed to fit into a + single 32-bit integer. When used as a data return format in memory, an + optional Length field and Extended Error Log data may follow the summary. + The fixed part contains a “presence” flag which identifies + whether an extended report is present. + + In the table below, the location of each field within the integer + is included in parentheses after its name. Numerical field values are + indicated in decimal unless noted otherwise. + + + RTAS Event Return Format (Fixed Part) + <emphasis>(Continued)</emphasis> + + + + + + + + Bit Field Name (bit + number(s)) + + + + + Description, Values (Described in + ) + + + + + + + + Version (0:7) + + + A distinct value used to identify the architectural + version of message. + + + + + Severity (8:10) + + + Severity level of error/event being reported: + ALREADY_REPORTED (6) + FATAL (5) + ERROR (4) + ERROR_SYNC (3) + WARNING (2) + EVENT (1) + NO_ERROR (0) + reserved for future use (7) + + + + + RTAS Disposition (11:12) + + + Degree of recovery which RTAS has performed prior to + return after an error (value is FULLY_RECOVERED if no error is + being reported): + FULLY_RECOVERED(0) + Note: Cannot be used when Severity is + “FATAL”. + LIMITED_RECOVERY(1) + NOT_RECOVERED(2) + reserved for future use (3) + + + + + Optional_Part_Presence (13) + + + Indicates if an Extended Error Log Length and Extended + Error Log follows this 32-bit quantity in memory: + PRESENT (1): The optional Extended Error Log is + present. + NOT_PRESENT (0): The optional Extended Error Log is not + present. + + + + + Reserved (14:15) + + + Reserved for future use (0:3) + + + + + Initiator (16:19) + + + Abstract entity that initiated the event or the failed + operation: + UNKNOWN (0): Unknown or Not Applicable + CPU (1): A CPU failure (in an MP system, the specific CPU + is not differentiated here) + PCI (2): PCI host bridge or PCI IOA + Reserved -- do not reuse (3) + MEMORY (4): Memory subsystem, including any caches + Reserved -- do not reuse (5) + HOT PLUG (6) + Reserved for future use (7-15) + + + + + Target (20:23) + + + Abstract entity that was apparent target of failed + operation (UNKNOWN if Not Applicable): Same values as Initiator + field + + + + + Type (24:31) + + + General event or error type being reported: +   + Internal Errors: + RETRY (1): too many tries failed, and a retry count + expired + TCE_ERR (2): range or access type error in an access + through a TCE + INTERN_DEV_FAIL (3): some RTAS-abstracted device has + failed (for example, TOD clock) + TIMEOUT (4): intended target did not respond before a + time-out occurred + DATA_PARITY (5): Parity error on data + ADDR_PARITY(6): Parity error on address + CACHE_PARITY (7): Parity error on external cache + ADDR_INVALID(8): access to reserved or undefined address, + or access of an unacceptable + type for an address + ECC_UNCORR (9): uncorrectable ECC error + ECC_CORR (10): corrected ECC error + RESERVED (11-63): Reserved for future use + Environmental and Power Warnings: + EPOW(64): See Extended Error Log for sensor value + RESERVED (65-95): Reserved for future use + Reserved -- do not reuse (96-159) +   + Platform Resource Reassignment (160) -- includes Change + Scope in bits 32-63 +   + Reserved for future use (through-223) +   + Platform Error (224) (for Version 6 or later) + ibm,io-events (225) (for Version 6 or later) + Platform information event (226) (for Version 6 or + later) + Resource deallocation event (227) (for Version 6 or + later) + Dump notification event (228) (for Version 6 or + later) +   + Vendor-specific events(229-255): Non-architected +   + Other (0): none of the above + + + + + Extended Event Log Length / Change Scope + (32:63) + + + Length in bytes of Extended Event Log information which + follows (see + ) OR the scope + parameter to be input the + ibm,update-nodes RTAS to retrieve the nodes + that were changed by selected “Hot Plug” + events. + + + + +
+ + Typically, most OSs care about, and have handlers for, only a few + specific errors. Since coding of an error is unique in the above scheme, + an OS can check for specific errors, then if nothing matches exactly, + look at more generic parts of the error message. This permits generic + error message generation for the user, providing the basic information + that RTAS delivered to the OS. Platforms may provide more complete error + diagnosis and reporting in RTAS, combined with off-line diagnostics which + take advantage of the information reported from previous failures. + +
+ +
+ +
+ Version 6 Extensions of Event Log Format + +
+ RTAS General Extended Event Log Format, Version 6 + + The following section defines new extensions to the event log + format which are identified by a Version number 0x06 in the first byte in + the returned buffer (byte 0 of the fixed-part information). The following + tables define extended error log formats for Version 6, by which the RTAS + can optionally return detailed information to the software about a + hardware error condition. Other versions will be defined in following + sections of this chapter. This format is also intended to be usable as + residual error log data in NVRAM, so that the OS could alternatively + retrieve error data after an error event which caused a reboot. + + Platforms indicate the maximum length of the error log buffer in + the + “rtas-error-log-max” RTAS property in the + OF device tree, so that the OS can allocate a buffer large enough to hold + the extended error log data when calling the RTAS + event-scan or + check-exception functions. If the allocated buffer is + not large enough to hold all the error log data, the data is truncated to + the size of the buffer. + + Requirement + and + require that four bytes of the + vendor-specific format contain a unique identifier for the company that + has defined the format. The description of the “name” string + in + provides alternatives for + defining this identifier. Examples of these unique identifiers include + stock ticker labels and Organizationally Unique Identifiers (OUIs). Since + the different options in IEEE 1275 provide different guarantees of + uniqueness and different identifier lengths, the company should use its + best judgement in selecting a unique identifier that fits the four + character field. The length of this field is limited to 4 bytes to + conserve available log data space. As an example, if Allied Information + Monitoring (a fictional name for the purposes of this example) were to + create a vendor-specific log format 12, then bytes 12-15 of such a log + may contain “AIM<NULL>”. + + This identifier is intended to apply to the company that defines + the specific format, and may be used by other companies that wish to be + compatible with that format. For example, if another company wanted to + take advantage of existing support in one of the OSs by using an + AIM-specific error log format for logs generated on their own platform, + their log would have to contain an identifier of + “AIM<NULL>”. + + + + + R1--1. + + Platforms which + support Version 6 of the Extended Event Log Format must do so by + including a 0x06 value in the first byte of the RTAS Event Return Format + (Fixed Part) and using the formats described in + (and all subsections under that + section). + + + Software Implementation Note: OSs running on + platforms which support Version 6 of the Extended Event Log Format must + ensure that the length parameter passed in the + event-scan RTAS call be at least 2 KB. + + + + + R1--2. + + If the length parameter on the RTAS + event-scan call for returning data using Version 6 of + the Extended Event Log Format is insufficient to return all the data the + platform would otherwise make available, the platform must truncate the + data by eliminating optional sections entirely rather than truncating a + section. + + + + + R1--3. + + All event logs returning a Version 6 + Platform Event Log format must include the Main-A and Main-B Sections. + Other sections are optional depending on the specific event type as + specified in Requirement + . + + + + + R1--4. + + The following + sections must be provided as indicated: + + + + For the Platform error Type, the Primary Service Reference Code + (SRC) section must be provided. + + + + For the ibm,io-events Type, the IO Events section must be + provided. + + + + For the Resource deallocation event Type, the Logical Resource + Identification section must be provided. + + + + For the Dump notification event Type, the Dump Locator section + must be provided. + + + + For the EPOW Type, the EPOW section must be provided. + + + + + + + + + + + Software Implementation Note: All fields in the + Platform Event Log marked “Platform specific information” or + “Other platform specific information sections” contain + information reserved for platform or platform Service Application use + only. That information is not defined in this document. Information in + these fields should be ignored by the OS. + + + Software Implementation and Architecture Note: All + fields currently marked “Reserved” are set to zero by RTAS + and are ignored by the OS. The reserved values in the defined fields in + the Platform Event Log may be defined in the future in this architecture + document for platform specific usage without change to this + architecture. + + + RTAS General Extended Event Log Format, Version 6 + + + + + + + + Byte + + + Bit + + + Description + + + + + + + 0 + + + 0 + + + 1 = Log Valid + + + + + 1 + + + 1 = Unrecoverable Error + + + + + 2 + + + 1 = Recoverable (correctable or successfully retried) + Error + + + + + 3 + + + 1 = Unrecoverable Error, Bypassed - Degraded operation + (e.g. CPU/memory taken off-line, bad cache bypassed, + etc.) + + + + + 4 + + + 1 = Predictive Error - Error is recoverable, but + indicates a trend toward unrecoverable failure (e.g. + correctable ECC error threshold, etc.) + + + + + 5 + + + 1 = “New” Log (always 1 for data returned + from RTAS) + + + + + 6 + + + 1 = Big-Endian + + + + + 7 + + + Reserved + + + + + 1 + + + 0:7 + + + Reserved + + + + + 2 + + + 0 + + + Set to 1 - (Indicating log is in PowerPC format) + + + + + 1:3 + + + Reserved + + + + + 4:7 + + + Log format indicator, defined format used for byte + 12-2047: + 0-13, 15 Reserved + 14: Platform Event Log + + + + + 3 + + + 0:7 + + + Reserved + + + + + 4-11 + + +   + + + Reserved + + + + + 12-15 + + +   + + + Company identifier of the company that has defined the + format for this vendor specific log type. + + + + + 16-2047 + + +   + + + Detail vendor specific log data. If byte 2, bits 4:7, + above, are a value of 14 (Platform Event Log) and bytes 12-16 + are “IBM ”, then see + for the content of + this field. + + + + +
+ +
+ +
+ Platform Event Log Format, Version 6 + + This format is used when byte 2, bits 4:7, of the RTAS General + Extended Event Log Version 6 are a value of 14 (Platform Event + Log). + + + Overview of Platform Event Log Format, Version + 6 + + + + + + + + Byte + + + Length in Bytes + + + Description + + + + + + + 12-15 + + + 4 + + + Contains ASCII characters + “IBM<NULL>”. + + + + + 16-63 + + + 48 + + + Main-A section (ID = 'PH'). Required section. See + for the + format. + + + + + 64-87 + + + 24 + + + Main-B section (ID = 'UH'). Required, always follow + Main-A section. See + for the + format. + + + + + 88-103 + + + 16 + + + Logical Resource Identification section (ID = 'LR'). + Optional, present only for Resource deallocation event + notification. If present, this section always follows Main-B + section. See + for the + format. + + + + + 104- + + + 80+ + optional FRU call out sub-section + + + Primary SRC section (ID = 'PS'). Required for + “Platform Error” event type, optional for other + event types. If present, this section always follows Main-B + section. See + for the + format. + + + + +   + + + 64 + + + Dump Locator section (ID = 'DH') Optional, present only + for dump event notification. If present, this section follows + Main-B or Primary SRC section. See + for the + format. + + + + +   + + + 20 + + + EPOW section (ID = 'EP'). Optional, present only for + “EPOW” interrupt event notification. If present, + this section follows Main-B section. See + for the + format. + + + + +   + + + Variable + + + IO Events section (ID = 'IE'). Optional, present only for + “ibm,io-events” interrupt event notification. If + present, this section follows Main-B section. See + for the + format. + + + + +   + + + 28 + + + Failing Enclosure MTMS section (ID = 'MT'). Required for + errors only. If present, this section follows Main-B section or + Primary SRC. See + for the + format. + + + + +   + + + 28 + + + Impacted partition description section (ID = 'LP''). + Required for errors only. If present, this section follows + Main-B section or Primary SRC + + + + +   + + + 40 + + + Machine Check Interrupt section (ID = 'MC'). Optional for + “Platform Error” event types with ERROR_SYNC + severity caused by a machine check interrupt. If present, this + section follows the Main-B. See + . + + + + + ...- 2047 + + + Variable + + + Other platform specific information sections. + Optional. + + + + +
+ +
+ +
+ Platform Event Log Format, Main-A Section + + + Platform Event Log Format, Version 6, Main-A + Section + + + + + + + + Offset + + + Length in Bytes + + + Description + + + + + + + 0x00 + + + 2 + + + Section ID: A two-ASCII character field which uniquely + identifies the type of section. + value = 'PH' + + + + + 0x02 + + + 2 + + + Section length: Length in bytes of the section, including + the section ID. + value = 48 + + + + + 0x04 + + + 1 + + + Section Version + + + + + 0x05 + + + 1 + + + Section sub-type + + + + + 0x06 + + + 2 + + + Creator Component ID + + + + + 0x08 + + + 4 + + + Log creation date in BCD format: YYYYMMDD, where YYYY = + year, MM = month 01 - 12, DD = day 01 - 31. + + + + + 0x0C + + + 4 + + + Log creation time in BCD format: HHMMSS00, where HH = + hour 00 - 23, MM = minutes 00 - 59, SS = s econds 00 -5 9, 00 = + hundredth of seconds 00 - 99. + + + + + 0x10 + + + 8 + + + Platform specific information + + + + + 0x18 + + + 1 + + + Creator ID -- subsystem creating the log entry + represented as a single ASCII character + 'E' = Service Processor + 'H' = Hypervisor, + 'W' = Power Control + 'L' = Partition Firmware + + + + + 0x19 + + + 2 + + + Reserved + + + + + 0x1B + + + 1 + + + Section count -- number of sections comprising log entry, + including this section + + + + + 0x1C + + + 4 + + + Reserved + + + + + 0x20 + + + 8 + + + Platform specific information + + + + + 0x28 + + + 4 + + + Platform Log ID (PLID) + Unique identifier for a single event. Note that it is + possible for multiple log entries to be made for a single + error/event. The entries are linked to the same event by using + the same PLID. + + + + + 0x2C + + + 4 + + + Platform specific information + + + + +
+ +
+ +
+ Platform Event Log Format, Main-B Section + + + Platform Event Log Format, Version 6, Main-B + Section + + + + + + + + Byte + + + Length in Bytes + + + Description + + + + + + + 0x00 + + + 2 + + + Section ID: A two-ASCII character field which uniquely + identifies the type of section. + value = 'UH' + + + + + 0x02 + + + 2 + + + Section length: Length in bytes of the section, including + the section ID. + value = 24 + + + + + 0x04 + + + 1 + + + Section Version + + + + + 0x05 + + + 1 + + + Section subtype + + + + + 0x06 + + + 2 + + + Creator Component ID + + + + + 0x08 + + + 1 + + + Subsystem ID: For error events, this is the failing + subsystem. For non-error events, this is the subsystem + associated with the event. + 0x10 - 0x1F = Processor subsystem including internal + cache + 0x20 - 0x2F = Memory subsystem including external + cache + 0x30 - 0x3F = I/O subsystem (hub, bridge, bus) + 0x40 - 0x4F = I/O adapter, device and peripheral + 0x50 - 0x5F = CEC hardware + 0x60 - 0x6F = Power/Cooling subsystem + 0x70 - 0x79 = Others subsystem + 0x7A - 0x7F = Surveillance Error + 0x80 - 0x8F = Platform Firmware + 0x90 - 0x9F = Software + 0xA0 - 0xAF = External environment + 0xB0 - 0xFF = Reserved + + + + + 0x09 + + + 1 + + + Platform specific information + + + + + 0x0A + + + 1 + + + Event/Error Severity (see additional description + following the table) + 0x00 = Informational or non- error Event. This field must + be 0x00 for non-error event. Use Event Sub-type field to + specify unique event. + 0x1X = Recovered Error + 0x10 = Recovered Error, general + 0x14 = Recovered Error, spare capacity utilized + 0x15 = Recovered Error, loss of entitled capacity + 0x2X = Predictive Error + 0x20 = Predictive Error, general + 0x21 = Predictive Error, degraded performance + 0x22 = Predictive Error, fault may be corrected after + platform re-boot + 0x23 = Predictive Error, fault may be corrected after + boot, degraded performance + 0x24 = Predictive Error, loss of redundancy + 0x4X = Unrecoverable Error + 0x40 = Unrecoverable Error, general + 0x41 = Unrecoverable Error, bypassed with degraded + performance + 0x44 = Unrecoverable Error, bypassed with loss of + redundancy + 0x45 = Unrecoverable Error, bypassed with loss of + redundancy and performance + 0x48 = Unrecoverable Error, bypassed with loss of + function + 0x6X = Error on diagnostic test + 0x60 = Error on diagnostic test, general + 0x61 = Error on diagnostic test, resource may produce + incorrect results + All other values = reserved + + + + + 0x0B + + + 1 + + + Event Sub-Type (primarily used when Event Severity = + 0x00, see additional description following the table) + 0x00 = not applicable. + 0x01 = Miscellaneous, Information Only + 0x08 = Dump Notification (Dump may also be reported on + Error event) + 0x10 = Previously reported error has been corrected by + system + 0x20 = System resources manually deconfigured by + user + 0x21 = System resources deconfigured by system due to + prior error event + 0x22 = Resource deallocation event notification + 0x30 = Customer environmental problem has returned to + normal + (e.g. input power restored, ambient temperature back + within limits) + 0x40 = Concurrent Maintenance Event + 0x60 = Capacity Upgrade Event + 0x70 = Resource Sparing Event + 0x80 = Dynamic Reconfiguration Event (generated by + RTAS) + 0xD0 = Normal system/platform shutdown or powered + off + 0xE0 = Platform powered off by user without normal + shutdown (abnormal power off) + All other values = reserved + + + + + 0x0C + + + 4 + + + Platform specific information + + + + + 0x10 + + + 2 + + + Reserved + + + + + 0x12 + + + 2 + + + Error Action Flags (see additional description following + the table) + bit 0 (0x8000) = 1, Service Action (customer + notification) Required + bit 1 (0x4000) = 1, Hidden Error - exclusive with SA + Required (bit 0) + bit 2 (0x2000) = 1, Report Externally (send to HMC and + hypervisor) + bit 3 (0x1000) = 1, Don't report to hypervisor (only + report to HMC) + (only meaningful when (bit 2) Report Externally is + set) + bit 4 (0x0800) = 1, Call Home Required + (only valid if (bit 0) SA Required is set) + bit 5 (0x0400) = 1, Error Isolation Incomplete. Further + analysis required. + bit 6 (0x0200) = 1, Deprecated. + bit 7 (0x0100) = 1, Reserved + bit 8, 9 = Platform specific information + bit 10-15 = Reserved + + + + + 0x14 + + + 4 + + + Reserved + + + + +
+ +
+ Error/Event Severity + + This field indicates the severity of the error event and the impact + of the error to the platform (if applicable). + + Non-error or Informational Event: + This value indicates an event + that is a non-error event. Informational or user action event log entries + must use this value. The Event Type field provides additional event + information. + + Recovered Error, general: + This value indicates an error event that + has been automatically recovered or corrected by the platform hardware + and/or firmware, e.g. ECC, internal spare or redundancy, cache line + delete, boot time array repair, etc. No service action is required for + this type of error. In general, when this value is used, the Error Action + Flags has the value of “Hidden Error”. An event log with this + value is used primarily for error thresholding design and code debug or + as a record to indicate error frequency or trend. + + + Recovered Error, spare capacity utilized: + This value + indicates that an error on a resource has been recovered by utilizing + another resource not currently assigned for use (spare). The failing + component is to be considered permanently in an error state. For example, + a faulty instruction on one processor may be checkpointed and loaded into + a spare processor, continuing the operations of the faulty one. In this + case the failing component is considered permanently in an error + state. + + + Recovered Error, loss of entitled capacity: + This value indicates that an error on a resource has been recovered by + utilizing another resource already in use by the system. The failing + component is to be considered permanently in an error state. This results + in a loss of capacity in the partition that receives the error. For + example, a processor already in use may take over the operations of a + faulty one. Loss of the faulty processor in the system then results in + less capacity being available to the partition receiving the error event. + Typically this event would have an event sub-type of “Resource + deallocation event notification” and the revised amount of entitled + capacity would be found in the Logical Resource Identification Section, + Entitled Capacity field. + + Predictive Error, general: + This value indicates an event that has + been automatically recovered or corrected by the platform hardware and/or + firmware. However, the frequency of the errors indicates a trend toward + (or potential) platform unrecoverable error. A deferred service or repair + action is required. The automatic platform recovery actions have no + impact to system performance (e.g. ECC, CRC, etc.), or the impact is + unknown. + + Predictive Error, degraded performance: + This value indicates an + error event that has been automatically recovered or corrected by the + platform hardware and/or firmware. However, the frequency of the errors + (i.e. over threshold) indicates a trend toward (or potential) platform + unrecoverable error. A deferred service or repair action is required. The + automatic platform recovery actions are impacting/degrading system + performance. + + Predictive Error, fault may be corrected after + platform re-boot: + This value indicates an error event that has been automatically recovered + or corrected by the platform hardware and/or firmware. However, the + frequency of the errors (i.e. over threshold) indicates a trend toward + (or potential) platform unrecoverable error. A deferred service or repair + action is required. The hardware fault may be corrected after platform + re-boot as part of the repair action. If the fault cannot be corrected + after re-boot, then a part replacement is required. The automatic + platform recovery actions have no impact to system performance (e.g. ECC, + CRC, etc.), or the impact is unknown. + + Predictive Error, fault may be corrected + after platform re-boot, degraded performance: + This value indicates an error event that has been + automatically recovered or corrected by the platform hardware and/or + firmware. However, the frequency of the errors (i.e. over threshold) + indicates a trend toward (or potential) platform unrecoverable error. A + deferred service or repair action is required. The hardware fault may be + corrected after platform re-boot as part of the repair action. If the + fault cannot be corrected after re-boot, then a part replacement is + required. The automatic platform recovery actions are impacting/degrading + the system performance. + + Predictive Error, loss of redundancy: + This value indicates an error + event that has been automatically recovered or corrected by the platform + hardware and/or firmware. However, the frequency of the errors (i.e. over + threshold) caused a loss in hardware redundancy. Future error in this + subsystem may causes platform unrecoverable error. A deferred service or + repair action is required to restore redundancy. The loss of redundancy + may or may not impact system performance. + + Unrecoverable Error, general: + This value indicates an error event + that is unrecoverable or uncorrectable by the platform hardware and/or + firmware. The hardware or platform resource with the error cannot be + deconfigured from the system. If the error is intermittent or soft, the + platform may be able to re-boot successfully and resume. A service or + repair action is required as soon as possible to correct the + error. + + Unrecoverable Error, bypassed with degraded + performance: This value + indicates an error event that is unrecoverable or uncorrectable by the + platform hardware and/or firmware. However, the hardware or platform + resource with the error has been deconfigured from the system. The + platform can be IPLed or re-IPLed with the error bypassed. System + performance is degraded due to the deconfigured platform resource(s) e.g. + processor, cache, memory, etc. A deferred service or repair action is + required. + + Unrecoverable Error, bypassed with loss + of redundancy: This value + indicates an error event that is unrecoverable or uncorrectable by the + platform hardware and/or firmware. However, the hardware or platform + resource with the error can be deconfigured from the system. The platform + can be IPLed or re-IPLed with the error bypassed. The deconfigured + platform resource(s) resulted in loss of redundancy (e.g. Redundant FSP + with static fail-over) with no loss of system performance. A deferred + service or repair action is required. + + Unrecoverable Error, bypassed with loss + of redundancy + performance: + This value indicates an error event that is unrecoverable or + uncorrectable by the platform hardware and/or firmware. However, the + hardware or platform resource with the error can be deconfigured from the + system. The platform can be IPLed or re-IPLed with the error bypassed. + The deconfigured platform resource(s) resulted in loss of redundancy and + system performance. A deferred service or repair action is + required. + + Unrecoverable Error, bypassed with loss + of function: This value + indicates an error event that is unrecoverable or uncorrectable by the + platform hardware and/or firmware. However, the hardware or platform + resource with the error can be deconfigured from the system. The platform + can be IPLed or re-IPLed with the error bypassed. The deconfigured + platform resource(s) resulted in loss of platform or system function. A + deferred service or repair action is required. + + Error on diagnostic test, general: + This value indicates an error + event that is detected during a diagnostic test. Impact to the system is + undefined or unknown. + + Error on diagnostic test, resource may + produce incorrect results: + This value indicates an error event that is detected during a diagnostic + test. The error may produce incorrect computational results (e.g. + processor floating point unit test error). + +
+ +
+ Event Sub-Type + + This field provides additional information on the non-error event + type. + + Not applicable: + This value is used when the event is associated + with an error. Error/Event Severity field and SRC section provide + additional error information. + + Miscellaneous, Information Only: + This value is used when the event + is “for information only” or the event description doesn't + fit into any other defined values in this field. + + Dump Notification: + This value is used by the hypervisor or + partition firmware as a “Dump Notification” event to the OS + that a dump file is present in the platform for retrieval by the OS. This + value is used by the HMC as a “Dump Notification” event to + the Service Application to indicate a dump file is present for + transmission to the manufacturer. + + Previously reported error has been + corrected by system: This value + is used by the platform firmware to indicate that the error event that + was previously reported has been corrected by the platform. On a + subsequent platform boot, this event type is logged to indicate that the + array was successfully repaired. + + System resources manually deconfigured + by user: This value is used + by the platform firmware to indicate that a subset of platform + resource(s) was/were deconfigured due to user's request (e.g. via + platform ASM menu). The deconfigured resource(s) is/are not associated + with error detected by the platform. The event is a reminder to the user + that the platform is running with partial capacity. + Note: The platform + provides this user option for platform performance testing + purpose. + + System resources deconfigured by + system due to prior error event: + This value is used by the platform firmware to indicate that the platform + is IPLed with resource(s) deconfigured due to error detected and reported + previously. The event is a reminder to the user that the platform + requires service. + + Resource deconfiguration notification: + This value is used by + partition firmware as an “Event Notification” to the OS that + a specified resource (e.g. processor, memory page, etc.) currently used + by the OS should be deallocated due to predictive error. A Logical + Resource Identification section is included in the event log to indicate + the Resource Type and ID. + + Customer environmental problem has + returned to normal: This value + is used by the platform firmware to indicate that a customer + environmental problem (e.g. utility power, room ambient temperature, + etc.) detected and reported previously, has returned to normal. + + Concurrent Maintenance: + This value is used by the platform firmware + to indicate any non-error event associated with concurrent maintenance + activity. + + Capacity Upgrade Event: + This value is used by the platform firmware + to indicate any non-error event associated with capacity upgrade + activity. + + Resource Sparing Event: + This value is used by the platform firmware + to indicate any non-error event associated with platform resource sparing + activity. + + Dynamic Reconfiguration Event: + This value is used by the partition + firmware to indicate any significant but non-error event associated with + dynamic reconfiguration activity. + Implementation Note: Due to limited + platform storage resource, non-error event log associated with a logical + partition will be reported to the OS but may not be stored in the + platform. + + Normal system/platform shutdown or + powered off: This value is used + by the platform firmware to indicate any non-error event associated with + normal system/platform shutdown or powered off activity initiated by the + user. + + Platform powered off by user without + normal shutdown (abnormal powered off): + This value is used by the platform firmware to indicate + that the platform is abnormally powered off by the user. + +
+ +
+ Error Action Flags + + The following are the definitions of the actions taken for the + various Error Action Flags. + + Report Externally - + This flag instructs the service processor + (error logger component) to send the error to the service application + (e.g. service focal point(s) or FNM error analyzer). If this flag is set, + the SP always sends the error: + + + + + To the “managing HMC(s)” if one (or multiple) + exists. + + + + + And to the hypervisor (unless the “Don't report to + hypervisor” flag is also set). + + + + + Service Action Required - + This flag instructs the Service + application that some service action is required by either the customer + or by the manufacturer’s service personnel. This is equivalent to + saying Customer Notification is required. Contrast this flag with the + “Call Home Required” flag. + + Call Home Required - + This flag indicates that the error requires + service and a Call Home Operation is to be performed. There are + additional policies used in combination with this flag: what subsystem + performs the Call Home, what is sent and where it is sent. + + Hidden Error - + This flag allows errors to be placed in a + partition's OS error log, but still remain hidden from the customer. This + is a legacy function and the partition firmware for must filter errors + marked “Hidden” and not forward these errors marked with this + flag to the OS. Note that this flag has no impact on the SP reporting + errors to either the HMC or hypervisor or for the hypervisor reporting + errors to partitions. + + Don't report Error to hypervisor - + While a partition is booting and + before it is functional (e.g. no OS error logging available), partition + errors may be sent through the hypervisor to the Service Processor). + These partition errors (and only partition errors) may be marked with + this flag to indicate that they need not be sent back to the hypervisor. + This is due to the error scope being limited to the failing partition and + the hypervisor has already taken the appropriate actions. + + Incomplete Information for Error + Isolation - Some errors are not + contained to a single enclosure and require error isolation from an + entity with broader system view / scope. + + Software Error - + This flag is used by the partition error logger to + indicate to the error is most likely to be caused by the software. When + both Software Error and Hardware Error flags are set, the error is caused + by either software or hardware. The Software Error and Hardware Error + flags are used to trigger the manufacturer’s support system to + automatically download software or firmware fixes. + + Hardware Error - + This flag is used by the partition error logger to + indicate to the error is most likely to be caused by the hardware. The + Software Error and Hardware Error flags are used to trigger the + manufacturer’s support system to automatically download software or + firmware fixes. + +
+ +
+ +
+ Platform Event Log Format, Logical Resource + Identification section + + + Platform Event Log Format, Version 6, Logical + Resource Identification Section + + + + + + + + Offset + + + Length in Bytes + + + Description + + + + + + + 0x00 + + + 2 + + + Section ID: A two-ASCII character field which uniquely + identifies the type of section. + value = 'LR' + + + + + 0x02 + + + 2 + + + Section length: Length in bytes of the section, including + the section ID. + value = 20 + + + + + 0x04 + + + 1 + + + Section Version + + + + + 0x05 + + + 1 + + + Section subtype + + + + + 0x06 + + + 2 + + + Creator Component ID + + + + + 0x08 + + + 1 + + + Resource Type + 0x10: Processor + 0x11: Shared processor + 0x40: Memory page + 0x41: Memory LMB + All other values = reserved + + + + + 0x09 + + + 1 + + + Reserved + + + + + 0x0A + + + 2 + + + Entitled Capacity: Hundredths of a CPU (only used for + Resource Type = Shared processor, value = 0x0000 for + others) + + + + + 0x0C + + + 4 + + + Logical CPU ID: for resource type = processor + DRC Index, for resource type = memory LMB + Memory Logical Address (bit 0-31), for resource type = + memory page + + + + + 0x10 + + + 4 + + + Memory Logical Address (bit 32-64)), for resource type = + memory page + + + + +
+ +
+ +
+ Platform Event Log Format, Primary SRC Section + + + Platform Event Log Format, Version 6, Primary SRC + Section + + + + + + + + Offset + + + Length in Bytes + + + Description + + + + + + + 0x00 + + + 2 + + + Section ID: A two-ASCII character field which uniquely + identifies the type of section. + value = 'PS' + + + + + 0x02 + + + 2 + + + Section length: Length in bytes of the section, including + the section ID. + value = 80 + optional FRU call out sub section + + + + + 0x04 + + + 1 + + + Section Version + + + + + 0x05 + + + 1 + + + Section Subtype + + + + + 0x06 + + + 2 + + + Creator component ID + + + + + 0x08 + + + 1 + + + SRC Version + + + + + 0x09 + + + 1 + + + SRC Flags + bit 0:6 = Platform specific information + bit 7 = 1: Additional/Optional sub-sections + present + + + + + 0x0A + + + 6 + + + Platform specific information + + + + + 0x10 + + + 4 + + + Extended Reference Code hex data word 2 (required) + + + + + 0x14 + + + 4 + + + Extended Reference Code hex data word 3 (optional) + + + + + 0x18 + + + 4 + + + Extended Reference Code hex data word 4 (optional) + + + + + 0x1C + + + 4 + + + Extended Reference Code hex data word 5 (optional) + + + + + 0x20 + + + 4 + + + Extended Reference Code hex data word 6 (optional) + + + + + 0x24 + + + 4 + + + Extended Reference Code hex data word 7 (optional) + + + + + 0x28 + + + 4 + + + Extended Reference Code hex data word 8 (optional) + + + + + 0x2C + + + 4 + + + Extended Reference Code hex data word 9 (optional) + + + + + 0x30 + + + 32 + + + Primary Reference Code: 32 byte ASCII character + (required) + + + + + Additional/Optional Sub section for FRU call out (present + only for “Platform Error” event type) + + + + + 0x00 + + + 1 + + + Sub section ID = C0 for FRU call out + + + + + 0x01 + + + 1 + + + Platform specific information + + + + + 0x02 + + + 2 + + + Length of sub section: expressed in # of words (4 bytes), + from Sub section ID field + + + + +   + + + FRU call out structure length + + + FRU call out 1 (see FRU call out structure format + below) + + + + +   + + +   + + + FRU call out 2 (call out 2-10 are optional) + + + + +   + + +   + + + ... + + + + +   + + +   + + + FRU call out 10 (maximum) + + + + +
+ + + Platform Event Log Format, Version 6, FRU Call-out + Structure + + + + + + + + Offset + + + Length in Bytes + + + Description + + + + + + + 0x00 + + + 1 + + + Call-out Structure length, in bytes including all fields, + including this one. + + + + + 0x01 + + + 1 + + + Call-out Type / Flags + bits 0-3: Call-out structure type + 0b0010 = this structure + bit 4 = 1 FRU Identity (ID) Substructure field included + in this FRU Call-out structure + bit 5 = 1 Other platform-only use substructure field + present following FRU ID substructure + bit 6-7 = 0b11: Other platform-only use substructure + field present following FRU ID substructure + + + + + 0x02 + + + 1 + + + FRU Replacement or Maintenance Procedure Priority + (expressed as an ASCII character, see additional description + following the table) + 'H' = High priority and mandatory call-out. + 'M' = Medium priority. + 'A' = Medium priority group A (1st group). + 'B' = Medium priority group B (2nd group). + 'C' = Medium priority group C (3rd group). + 'L' = Low priority. + + + + + 0x03 + + + 1 + + + Length of Location Code field - must be a multiple of + 4. + + + + + 0x04 + + + variable + max=80 + + + Location Code + NULL terminated ASCII string. May be up to 80 characters + including the NULL. Padded with extra NULLs to 4-byte + boundary. + + + + + FRU Identity Substructure follow: + + + + + 0x00 + + + 2 + + + Substructure Type (2 ASCII Characters) + 'ID' = FRU Identity Substructure + + + + + 0x02 + + + 1 + + + Substructure length (variable, several optional fields - + see flags below) + + + + + 0x03 + + + 1 + + + Flags + bits 0-3: Failing component Type (see additional + description following the table) + 0b0000: reserved + 0b0001: “normal” hardware FRU + 0b0010: code FRU + 0b0011: configuration error, configuration procedure + required + 0b0100: Maintenance Procedure required + 0b1001: External FRU + 0b1010: External code FRU + 0b1011: Tool FRU + 0b1100: Symbolic FRU + 0b1111: Reserved for expansion + all other values reserved + bit 4 (0x08) = 0b1: FRU Stocking Part Number supplied + (mutually exclusive with bit 6) + bit 5 (0x04) = 0b1: CCIN supplied (only valid if bit 4 = + 0b1) + bit 6 (0x02) = 0b1: Maintenance procedure call out + supplied (mutually exclusive with FRU p/n) + bit 7 (0x01) = 0b1: FRU Serial Number supplied (only + valid if bit 4 = 0b1) + + + + + 0x04 + + + 8, if present + + + FRU Stocking Part Number (VPD FN keyword) or Procedure + ID + This field is present if Flags bits 4 =0b1 or Flags bits + 6 =0b1. + It contains a NULL-terminated ASCII character + string. + If Flags bit 4 = 0b1, this field contains a 7ASCII + character part number + If Flags bit 6 = 0b1, this field contains a 5 ASCII + character procedure ID + + + + + 0x0C + + + 4, if present + + + CCIN (VPD CC keyword) (optional, only supplied if Part + Number also supplied) + This field is present if Flags bit 5 = 0b1. It contains + the CCIN of the failing FRU (VPD CC keyword), represented as 4 + ASCII characters (not a NULL-terminated string). + + + + +   + + + 12, if present + + + FRU Serial Number (VPD SE Keyword) (optional) + This field is present if Flags bit 7 = 0b1. It contains + the serial number of the failing FRU (VPD SE keyword), + represented as a 12 ASCII characters (not a NULL-terminated + string). + + + + + End of FRU Identify Substructure + + + + +   + + + variable + + + Other platform used only substructure field + + + + +
+ +
+ FRU Replacement or Maintenance Procedure + Priority + + This field defines the service priority of the specific call-out, + i.e., replacing the FRU part number or performing the maintenance + procedure ID as given in the FRU/Procedure Identity substructure. Here + are the priority descriptions: + + + + + 'H' = High priority and + mandatory call-out. Replacing the FRU (or + performing the maintenance procedure) is mandatory. If multiple call-outs + with 'H' priority are given, all must be replaced or performed as a + group. + + + + + 'M' = Medium priority. + Replacing the FRU (or performing + maintenance procedure) with 'M' priority one at a time in the order given + after all call-outs prior to this one, if present, are performed. + + + + + 'A' = Medium priority group A + (1st group). Replacing all the FRUs + with 'A' priority as a group after all call-outs prior to this group, if + present, are performed. + + + + + 'B' = Medium priority group B + (2nd group). Replacing all the FRUs + with 'B' priority as a group after all call-outs prior to this group, if + present, are performed. + + + + + 'C' = Medium priority group C + (3rd group). Replacing all the FRUs + with 'C' priority as a group after all call-outs prior to this group, if + present, are performed. + + + + + 'L' = Low priority. After + performed all the prior call-outs, if + present, and problem still persists, replacing the FRU with this priority + one at a time in the order given. + + + + + The list of FRU/Procedure call-outs in the “call-out” + subsection of the SRC structure must be in order as defined above, i.e. + High, Medium, Low. 'M' has the same medium priority level as 'A', 'B', or + 'C' and a call out with 'M' priority can precede or follow 'A', 'B' or + 'C'. A group call-out must be contiguous in the list. Within the medium + priority level, follow the call-out order in the list A list without High + or Medium priority is also valid. + +
+ +
+ Failing Component Type Description + + + + + Normal Hardware FRU: + Hardware FRU in the platform which the + platform firmware or code can positively identify, and its VPD contains + the part number and associated information. + + + + + Code FRU: + Some layer of platform firmware or OS code is + suspected. The procedure ID field provides additional information about + which code(s) is/are the potential problem. + + + + + Configuration error: + The problem may be related to how hardware + or code is configured. For example, an adapter is plugged in a slot that + cannot support it. The FRU could be a procedure or a symbolic FRU. The + reason to use one of these is if the analysis can provide more + information to the customer and service provider by giving a location + code. + + + + + Maintenance procedure required: + Further isolation of the problem + is required by performing the procedure as identified in the Procedure ID + field. Procedures are designed to help to isolate problems and guide the + service provider through identifying which FRUs to replace in which + order. + + + + + Symbolic FRU: Used for a single + FRU where the analysis code knows + exactly what the part is but there is no part number, or the part number + cannot be pulled from VPD, or when there is something special (like a + procedure) for acquiring the FRU or working with it. Examples are cables, + or FRUs without VPD (so a part number cannot be filled in). The term + “Symbolic” simply means “not an actual part + number”. + + + + + External FRU: A failing part(s) + which is/are not in the system, + e.g. attached storage sub-system, network hubs/switches, external drives + like CD/DVD boxes. + + + + + External Code: Code not running + in the platform but is the + potential source of the error. This could be something like storage + subsystem code or even another system in the same cluster. + + + + + Tool FRU: This is a special + tool that will be required by one of + the FRUs in the list. Tools are only added as FRUs when they are not part + of the CE tool kit and therefore the repair action could be delayed if + the CE did not know to bring it. Examples are Optical Cleaning Kits for + fiber channel, and special tools for torque or reach or weight + considerations. + + + + +
+ +
+ +
+ Platform Event Log Format, Dump Locator Section +   + + Platform Event Log Format, Version 6, Dump Locator + Section + + + + + + + + Offset + + + Length in Bytes + + + Description + + + + + + + 0x00 + + + 2 + + + Section ID: A two-ASCII character field which uniquely + identifies the type of section. + value = 'DH' + + + + + 0x02 + + + 2 + + + Section length: Length in bytes of the section, including + the section ID. + value = 64 + + + + + 0x04 + + + 1 + + + Section Version + + + + + 0x05 + + + 1 + + + Section Sub-Type + 0x00 = Log truncated, complete log received by another + service entity. + 0x01 = FSP Dump + 0x02 = Platform System Dump + 0x03 = Reserved + 0x04 = Power Subsystem Dump + 0x05 = Platform Event Log Entry Dump (when distinguishing + between dump types, the term “Log Dump” is + typically used) + 0x06 = Partition-initiated resource dump + 0x07 = Platform-initiated resource dump + All other values reserved + + + + + 0x0 + + + 2 + + + Creator component ID + + + + + 0x08 + + + 4 + + + Dump ID + + + + + 0x0C + + + 1 + + + Flags + bit 0 (0x80) = 0, Dump sent to partition + bit 0 = 1, Dump sent to HMC + bit 1 (0x40) = 0, File name in ASCII + bit 1 = 1, Dump file name is hex + bit 2 (0x20) = 1, Dump size field valid + + + + + 0x0D + + + 2 + + + Reserved + + + + + 0x0F + + + 1 + + + Length of OS assigned Dump ID field in bytes, must be + multiple of 4. + May be 0. + + + + + 0x10 + + + 8 + + + Dump Size + + + + + 0x18 + + + 40 + + + OS-Assigned Dump ID + As the flag field indicates, this field may either be an + ASCII string or a hex number. + When an ASCII string (AIX, Linux, HMC), this is a NULL + terminated ASCII string representing the dump file name (leaf + name only, does not include path). + Field may be up to 40 characters including the + NULL. + + + + +
+ +
+ +
+ Platform Event Log Format, EPOW Section + + + Platform Event Log Format, Version 6, EPOW + Section + + + + + + + + Offset + + + Length in Bytes + + + Description + + + + + + + 0x00 + + + 2 + + + Section ID: A two-ASCII character field which uniquely + identifies the type of section. + value = 'EP' + + + + + 0x02 + + + 2 + + + Section length: Length in bytes of the section, including + the section ID. + + + + + 0x04 + + + 1 + + + Section Version + + + + + 0x05 + + + 1 + + + Section subtype + + + + + 0x06 + + + 2 + + + Creator Component ID + + + + + 0x08 + + + 1 + + + EPOW Sensor Value (low-order 4 bits contain the action + code). + + + + + 0x09 + + + 1 + + + EPOW Event Modifier + (low-order 4 bits contain the event modifier + value) + 0x00 = Not applicable + For EPOW sensor value = 3 + 0x01 = Normal system shutdown with no additional + delay + 0x02 = Loss of utility power, system is running on + UPS/Battery + 0x03 = Loss of system critical functions, system should + be shutdown + 0x04 = Ambient temperature too high + All other values = reserved + + + + + 0x0A + + + 1 + + + Extended Modifier for Section Version 2 and higher + For EPOW Sensor Value = 3 + 0x00 System wide shutdown + 0x01 Partition specific shutdown + 0x02 - 0xFF Reserved + All other situations Reserved = 0x00 + + + + + 0x0B + + + 1 + + + Reserved + + + + + 0x0C + + + 8 + + + Platform specific reason code + + + + +
+ +
+ +
+ Platform Event Log Format, IO Events Section + + + Platform Event Log Format, Version 6, IO Events + Section + + + + + + + + Offset + + + Length in Bytes + + + Description + + + + + + + 0x00 + + + 2 + + + Section ID: A two-ASCII character field which uniquely + identifies the type of section. + value = 'IE' + + + + + 0x02 + + + 2 + + + Section length: Length in bytes of the section, including + the section ID. + + + + + 0x04 + + + 1 + + + Section Version + + + + + 0x05 + + + 1 + + + Section subtype + + + + + 0x06 + + + 2 + + + Creator Component ID + + + + + 0x08 + + + 1 + + + IO-Event Type: + 0x01 = Error Detected + 0x02 = Error Recovered + 0x03 = Event + 0x04 = RPC Pass Through + All other values = Reserved + + + + + 0x09 + + + 1 + + + Offset 0x10 Field Length: + For IO Event Type of RPC Pass Through, this field + specifies the length of the data field which begins at offset + 0x10, otherwise the value in this field is 0. Must be a + multiple of 4 to maintain 4-byte alignment. +   + + + + + 0x0A + + + 1 + + + Error/Event Scope: + 0x00 = Not Applicable (use for IO-Event type 0x02, 0x03, + 0x04) + 0x36 = Reserved + 0x37 = Reserved + 0x38 = PHB + 0x39 = Reserved + 0x3A = Reserved + 0x3B = Reserved + 0x51 = Service Processor + All other values = Reserved + + + + + 0x0B + + + 1 + + + I/O-Event Sub-Type: + 0x00 = Not Applicable (use for IO-Event type 0x01, 0x02, + 0x04) + 0x01 = Rebalance request + 0x03 = Node online + 0x04 = Node off-line + 0x05 = platform-dump-max-size change + 0x08 = Generic Notification + All other values = Reserved + + + + + 0x0C + + + 4 + + + DRC Index + + + + + 0x10 + + + 0-216 + + + For the RPC Pass Through IO Event Type: RPC data. + Variable length data. Must be padded to 4 bytes + alignment. +   + For the platform-dump-max-size change I/O-Event Sub-Type: + 8 bytes for the new value of the platform-dump-max-size system + parameter (specifying the sum (in bytes) of the maximum size of + each unique platform dump type that the + ibm,platform-dump RTAS call could + return). +   + For Generic Notification I/O Event Sub-Type: Scoped Data + Generic Notification Event Section. Must be padded to 4 bytes + alignment. + + + + +
+ +
+ +
+ Platform Event Log Format, Failing Enclosure + MTMS + + + Platform Event Log Format, Version 6, Failing + Enclosure MTMS + + + + + + + + Offset + + + Length in Bytes + + + Description + + + + + + + 0x00 + + + 2 + + + Section ID: A two-ASCII character field which uniquely + identifies the type of section. + value = 'MT' + + + + + 0x02 + + + 2 + + + Section length: Length in bytes of the section, including + the section ID. + value = 28 + + + + + 0x04 + + + 1 + + + Section Version + + + + + 0x05 + + + 1 + + + Section subtype + + + + + 0x06 + + + 2 + + + Creator Component ID + + + + + 0x08 + + + 8 + + + Machine Type and Model: 8 ASCII characters, in the form + “tttt-mmm”, + where tttt = Machine Type and mmm = Model Number + + + + + 0x10 + + + 12 + + + Serial Number: + 12 ASCII characters (If less than 12 characters are used, + string is left justified (stored in the field starting with the + lowest address) and padded with NULLs.) + + + + +
+ The Failing Enclosure Machine Type, Model, and Serial Number (MTMS) + that is associated with the error is important for service and + support. + + The source of information for the MTMS fields varies according to + the following: + + + + + For CEC errors, it is the CEC enclosure MTMS. + + + + + For errors in I/O enclosures (drawers and towers) that have their + own MTMS and are sold as separate MTMS from the CEC, we use the I/O + Drawer MTMS. + + + + + For I/O enclosures that were sold as a feature, this section + contains the Feature Code and Serial Number of the I/O enclosure. When + the Feature Code is used, it is left justified in the Machine Type and + Model field. + + + + +
+ +
+ Platform Event Log Format, Impacted Partitions + + + Platform Event Log Format, Version 6, Impacted + Partitions + + + + + + + + + + + Offset + + + Length + + + Byte 0 + + + Byte 1 + + + Byte 2 + + + Byte 3 + + + + + + + 0 + + + 8 + + + Section Header + + +   + + +   + + +   + + + + + 0x10 + + + 4 + + + Primary Partition ID + + + Length of LP name + (must be a multiple of 4) + + + Target LP Count + + +   + + + + + 0x14 + + + 4 + + + Logical Partition ID + + +   + + +   + + +   + + + + + 0x18 + + + variable + + + Primary Partition (LP) Name + Null terminated ASCII string, padded to 4-Byte + boundary + + +   + + +   + + +   + + + + +   + + + variable + + + Target LP 1 + + + Target LP 2 + and so on + (padded to a 4-Byte boundary) + + +   + + +   + + + + +
+ + This section describes partitions that are impacted by an error. + When this section is supplied, the partitions in this list (and only + these partitions) are notified of the error. + +
+ +
+ Platform Event Log Format, Failing Memory + Address + + + Platform Error Event Log Format, Version 6, Failing + Memory Address + + + + + + + + Offset + + + Length in Bytes + + + Description + + + + + + + 0x00 + + + 2 + + + Section ID: A two-ASCII character field which uniquely + identifies the type of section. + value = 'MC' + + + + + 0x02 + + + 2 + + + Section length: Length in bytes of the section, including + the section ID + value = 32 + + + + + 0x04 + + + 1 + + + Section Version + + + + + 0x05 + + + 1 + + + Section Subtype + + + + + 0x06 + + + 2 + + + Creator Component ID + + + + + 0x08 + + + 4 + + + FRU ID -- Identifies the FRU on which the machine check + interrupt occurred + + + + + 0x0C + + + 4 + + + Processor ID -- identifies the physical CPU on which the + machine check occurred + + + + + 0x10 + + + 1 + + + Type of machine check interrupt + 0x00 = Uncorrectable Memory Error (UE) + 0x01 = SLB error + 0x02 = ERAT Error + 0x04 = TLB error + 0x05 = D-Cache error + 0x07 = I-Cache error + + + + + 0x11 + + + 23 + + + Information specific to machine check interrupt type. + This section is binary zeroes if the platform does not provide + specific information for the type of interrupt. + + + + +
+ + + UE Error Information + + + + + + + + Offset + + + Length in Bytes + + + Description + + + + + + + 0x11 + + + 1 + + + Type of UE + Bit 0 = 0 Permanent UE. The UE may be cleared with a DCBZ + instruction. + Bit 0 =1 Transient UE. The UE cannot be cleared with a + DCBZ instruction. The contents of the entire logical page are + not accessible for this type of UE + 64 bit effective address is provided + Bit 1 = 0 64 bit effective address is not provided by the + log + Bit 1 = 1 64 bit effective address is provided by the + log. Offset 0x18 provides the effective address if this bit is + 1 + 64 bit logical address is provided + Bit 2 = 0 64 bit logical address of logical page is not + provided by the log + Bit 2 = 1 64 bit logical address of logical page is + provided by the log. Offset 0x20 provides the logical address + of the page if this bit is 1 + Bit3-4 Reserved + Bit5-7 Type of UE machine check interrupt. The value of + the field is 0b000 for a permanent UE + 0b000 = Platform cannot determine the processor unit that + detected the error + 0b001 = Error detected by instruction fetch unit of the + processor + 0b010 = Error during page table search for instruction + fetch + 0b011 = Error detected by load/store unit of the + processor + 0b100 = Error detected during page table search for + load/store type of instruction + All other values are reserved. + + + + + 0x12 + + + 6 + + + Reserved + + + + + 0x18 + + + 8 + + + 64 bit effective address + + + + + 0x20 + + + 8 + + + 64 bit logical address + + + + +
+ + + SLB Error Information + + + + + + + + Offset + + + Length in Bytes + + + Description + + + + + + + 0x11 + + + 1 + + + 64 bit effective address is provided + Bit 0 = 0 64 bit effective address not provided by the + log + Bit 0 =1 64 bit effective address provided by the log. + Offset 0x18 provides the effective address if bit 0 is1 + Bit1-5 Reserved + Bit 6-7 Type of SLB error + 0b00 = Parity error in the SLB array or on the access + path to the SLB + 0b01 = Multiple hit error. There are two or more entries + in the SLB that translate the same effective address + 0b10 = Multiple hit error or parity error. Platform does + not have enough information to disambiguate between the two + cases. + All other values are reserved. + + + + + 0x12 + + + 6 + + + Reserved + + + + + 0x18 + + + 8 + + + 64 bit effective address + + + + + 0x20 + + + 8 + + + Reserved + + + + +
+ + + ERAT Error Information + + + + + + + + Offset + + + Length in Bytes + + + Description + + + + + + + 0x11 + + + 1 + + + 64 bit effective address is provided + Bit 0 = 0 64 bit effective address not provided by the + log + Bit 0 =1 64 bit effective address provided by the log. + Offset 0x18 provides the effective address if bit 0 is1 + Bit 1-5 Reserved + Bit 6-7 Type of ERAT error + 0b01 = Parity error in the ERAT array + 0b10 = Multiple hit error. There are two or more entries + in the ERAT array that translate the same effective + address + 0b11 = Multiple hit error or parity error in the ERAT + array. Platform does not have enough information to + disambiguate between the two cases. + All other values are reserved. + + + + + 0x12 + + + 6 + + + Reserved + + + + + 0x18 + + + 8 + + + 64 bit effective address + + + + + 0x20 + + + 8 + + + Reserved + + + + +
+ + + TLB Error Information + + + + + + + + Offset + + + Length in Bytes + + + Description + + + + + + + 0x11 + + + 1 + + + 64 bit effective address is provided + Bit 0 = 0 64 bit effective address not provided by the + log + Bit 0 =1 64 bit effective address provided by the log. + Offset 0x18 provides the effective address if bit 0 is1 + Bit 1-5 Reserved + Bit 6-7 Type of TLB error + 0b01 = Parity error in the TLB array + 0b10 = Multiple hit error. There are two or more entries + in the TLB that translate the same effective address + 0b11= Multiple hit error or parity error in the TLB + array. Platform does not have enough information to + disambiguate between the two cases. + All other values are reserved. + + + + + 0x12 + + + 6 + + + Reserved + + + + + 0x18 + + + 8 + + + 64 bit effective address + + + + + 0x20 + + + 8 + + + Reserved + + + + +
+ + For an error log that has the machine check interrupt section + filled out, the platform is not required to provide the date and time + stamp in the main-a section. The fields will be binary zeroes if the date + and time stamp is not provided. + +
+ +
+ +
diff --git a/Error Handling/sec_rtas_hot_plug.xml b/Error Handling/sec_rtas_hot_plug.xml new file mode 100644 index 0000000..696b425 --- /dev/null +++ b/Error Handling/sec_rtas_hot_plug.xml @@ -0,0 +1,46 @@ + + +
+ + Hot Plug Events + + Hot Plug Events, when implemented, are reported through the + event-scan RTAS call. These events are surfaced through the fixed + portions of the RTAS return value. (see + ) Some parts of the system may + be modified without direct support from the OS. + + + + + R1--1. + + If FRUs can be hot plugged in the system + without OS support, the Hot Plug Event mechanism must be provided for + signaling the OS about the event. + + + + + +
diff --git a/LICENSE b/LICENSE new file mode 100644 index 0000000..68c771a --- /dev/null +++ b/LICENSE @@ -0,0 +1,176 @@ + + Apache License + Version 2.0, January 2004 + http://www.apache.org/licenses/ + + TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION + + 1. Definitions. + + "License" shall mean the terms and conditions for use, reproduction, + and distribution as defined by Sections 1 through 9 of this document. + + "Licensor" shall mean the copyright owner or entity authorized by + the copyright owner that is granting the License. + + "Legal Entity" shall mean the union of the acting entity and all + other entities that control, are controlled by, or are under common + control with that entity. For the purposes of this definition, + "control" means (i) the power, direct or indirect, to cause the + direction or management of such entity, whether by contract or + otherwise, or (ii) ownership of fifty percent (50%) or more of the + outstanding shares, or (iii) beneficial ownership of such entity. + + "You" (or "Your") shall mean an individual or Legal Entity + exercising permissions granted by this License. + + "Source" form shall mean the preferred form for making modifications, + including but not limited to software source code, documentation + source, and configuration files. + + "Object" form shall mean any form resulting from mechanical + transformation or translation of a Source form, including but + not limited to compiled object code, generated documentation, + and conversions to other media types. + + "Work" shall mean the work of authorship, whether in Source or + Object form, made available under the License, as indicated by a + copyright notice that is included in or attached to the work + (an example is provided in the Appendix below). + + "Derivative Works" shall mean any work, whether in Source or Object + form, that is based on (or derived from) the Work and for which the + editorial revisions, annotations, elaborations, or other modifications + represent, as a whole, an original work of authorship. For the purposes + of this License, Derivative Works shall not include works that remain + separable from, or merely link (or bind by name) to the interfaces of, + the Work and Derivative Works thereof. + + "Contribution" shall mean any work of authorship, including + the original version of the Work and any modifications or additions + to that Work or Derivative Works thereof, that is intentionally + submitted to Licensor for inclusion in the Work by the copyright owner + or by an individual or Legal Entity authorized to submit on behalf of + the copyright owner. For the purposes of this definition, "submitted" + means any form of electronic, verbal, or written communication sent + to the Licensor or its representatives, including but not limited to + communication on electronic mailing lists, source code control systems, + and issue tracking systems that are managed by, or on behalf of, the + Licensor for the purpose of discussing and improving the Work, but + excluding communication that is conspicuously marked or otherwise + designated in writing by the copyright owner as "Not a Contribution." + + "Contributor" shall mean Licensor and any individual or Legal Entity + on behalf of whom a Contribution has been received by Licensor and + subsequently incorporated within the Work. + + 2. Grant of Copyright License. Subject to the terms and conditions of + this License, each Contributor hereby grants to You a perpetual, + worldwide, non-exclusive, no-charge, royalty-free, irrevocable + copyright license to reproduce, prepare Derivative Works of, + publicly display, publicly perform, sublicense, and distribute the + Work and such Derivative Works in Source or Object form. + + 3. Grant of Patent License. Subject to the terms and conditions of + this License, each Contributor hereby grants to You a perpetual, + worldwide, non-exclusive, no-charge, royalty-free, irrevocable + (except as stated in this section) patent license to make, have made, + use, offer to sell, sell, import, and otherwise transfer the Work, + where such license applies only to those patent claims licensable + by such Contributor that are necessarily infringed by their + Contribution(s) alone or by combination of their Contribution(s) + with the Work to which such Contribution(s) was submitted. If You + institute patent litigation against any entity (including a + cross-claim or counterclaim in a lawsuit) alleging that the Work + or a Contribution incorporated within the Work constitutes direct + or contributory patent infringement, then any patent licenses + granted to You under this License for that Work shall terminate + as of the date such litigation is filed. + + 4. Redistribution. You may reproduce and distribute copies of the + Work or Derivative Works thereof in any medium, with or without + modifications, and in Source or Object form, provided that You + meet the following conditions: + + (a) You must give any other recipients of the Work or + Derivative Works a copy of this License; and + + (b) You must cause any modified files to carry prominent notices + stating that You changed the files; and + + (c) You must retain, in the Source form of any Derivative Works + that You distribute, all copyright, patent, trademark, and + attribution notices from the Source form of the Work, + excluding those notices that do not pertain to any part of + the Derivative Works; and + + (d) If the Work includes a "NOTICE" text file as part of its + distribution, then any Derivative Works that You distribute must + include a readable copy of the attribution notices contained + within such NOTICE file, excluding those notices that do not + pertain to any part of the Derivative Works, in at least one + of the following places: within a NOTICE text file distributed + as part of the Derivative Works; within the Source form or + documentation, if provided along with the Derivative Works; or, + within a display generated by the Derivative Works, if and + wherever such third-party notices normally appear. The contents + of the NOTICE file are for informational purposes only and + do not modify the License. You may add Your own attribution + notices within Derivative Works that You distribute, alongside + or as an addendum to the NOTICE text from the Work, provided + that such additional attribution notices cannot be construed + as modifying the License. + + You may add Your own copyright statement to Your modifications and + may provide additional or different license terms and conditions + for use, reproduction, or distribution of Your modifications, or + for any such Derivative Works as a whole, provided Your use, + reproduction, and distribution of the Work otherwise complies with + the conditions stated in this License. + + 5. Submission of Contributions. Unless You explicitly state otherwise, + any Contribution intentionally submitted for inclusion in the Work + by You to the Licensor shall be under the terms and conditions of + this License, without any additional terms or conditions. + Notwithstanding the above, nothing herein shall supersede or modify + the terms of any separate license agreement you may have executed + with Licensor regarding such Contributions. + + 6. Trademarks. This License does not grant permission to use the trade + names, trademarks, service marks, or product names of the Licensor, + except as required for reasonable and customary use in describing the + origin of the Work and reproducing the content of the NOTICE file. + + 7. Disclaimer of Warranty. Unless required by applicable law or + agreed to in writing, Licensor provides the Work (and each + Contributor provides its Contributions) on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or + implied, including, without limitation, any warranties or conditions + of TITLE, NON-INFRINGEMENT, MERCHANTABILITY, or FITNESS FOR A + PARTICULAR PURPOSE. You are solely responsible for determining the + appropriateness of using or redistributing the Work and assume any + risks associated with Your exercise of permissions under this License. + + 8. Limitation of Liability. In no event and under no legal theory, + whether in tort (including negligence), contract, or otherwise, + unless required by applicable law (such as deliberate and grossly + negligent acts) or agreed to in writing, shall any Contributor be + liable to You for damages, including any direct, indirect, special, + incidental, or consequential damages of any character arising as a + result of this License or out of the use or inability to use the + Work (including but not limited to damages for loss of goodwill, + work stoppage, computer failure or malfunction, or any and all + other commercial damages or losses), even if such Contributor + has been advised of the possibility of such damages. + + 9. Accepting Warranty or Additional Liability. While redistributing + the Work or Derivative Works thereof, You may choose to offer, + and charge a fee for, acceptance of support, warranty, indemnity, + or other liability obligations and/or rights consistent with this + License. However, in accepting such obligations, You may act only + on Your own behalf and on Your sole responsibility, not on behalf + of any other Contributor, and only if You agree to indemnify, + defend, and hold each Contributor harmless for any liability + incurred by, or claims asserted against, such Contributor by reason + of your accepting any such warranty or additional liability. + diff --git a/Platform/app_bibliography.xml b/Platform/app_bibliography.xml new file mode 100644 index 0000000..4d830bf --- /dev/null +++ b/Platform/app_bibliography.xml @@ -0,0 +1,284 @@ + + + + + Bibliography + This section lists documents which were referenced in this specification or which provide + additional information, and some useful information for obtaining these documents. Referenced + documents are listed below. When any of the following standards are superseded by an approved + revision, the revision shall apply. + + + + + + + + Linux on Power Architecture Reference: Device Tree + + + + + Linux on Power Architecture Reference: Error Recovery and Logging + + + + + Linux on Power Architecture Reference: Virtualization + + + + + Linux on Power Architecture Reference: Runtime Abstraction Services (RTAS) + + + + + Power ISA + + + + + IEEE 1275, IEEE Standard for Boot (Initialization Configuration) Firmware: + Core Requirements and Practices + IEEE part number DS02683, ISBN 1-55937-426-8 + + + + + Core Errata, IEEE P1275.7/D4 + + + + + Open Firmware Recommended Practice:OBP-TFTP + Extension + + + + + Open Firmware Recommended Practice: Device + Support Extensions + + + + + PCI Bus binding to: IEEE Std 1275-1994, Standard + for Boot (Initialization, Configuration) Firmware + + + + + Open Firmware: Recommended Practice - Interrupt + Mapping + + + + + Open Firmware: Recommended Practice - Forth Source + and FCode Image Support, Version 1.0 + + + + + Open Firmware: Recommended Practice - Interrupt + Mapping, Version 1.0 + + + + + Open Firmware: Recommended Practice - TFTP Booting + Extensions, Version 0.8 + + + + + Open Firmware: Recommended Practice - + Interposition, Version 0.2 + + + + + MS-DOS Programmer's Reference + Published by Microsoft + + + + + Peering Inside the PE: A Tour of the Win32 Portable + Executable File Format + Found in the March, 1994 issue of Microsoft Systems Journal + + + + + ISO-9660, Information processing -- Volume and + file structure of CD-ROM for information interchange + Published by International Organization for Standardization + + + + + System V Application Binary Interface, PowerPC + Processor Supplement + By Sunsoft + + + + + ISO Standard 8879:1986, Information Processing + -- Text and Office Systems -- Standard Generalized Markup Language (SGML) + + + + + IEEE 996, A Standard for an Extended Personal Computer + Back Plane Bus + + + + + PCI Local Bus Specification + All designers are responsible for assuring that they use the most current version of this document + at the time that they design conventional PCI related components or platforms. See the PCI SIG website + for the most current version of this document. + + + + + PCI-to-PCI Bridge Architecture Specification + All designers are responsible for assuring that they use the most current version of this document + at the time that they design conventional PCI related components or platforms. See the + PCI SIG website for the most current version of this document. + + + + + PCI Standard Hot-Plug Controller and Subsystem + Specification + + + + + PCI-X Protocol Addendum to the PCI Local Bus Specification + All designers are responsible for assuring that they use the most current version of this document at + the time that they design PCI-X related components or platforms. See the PCI SIG website for the most + current version of this document. + + + + + PCI Express Base Specification + All designers are responsible for assuring that they use the most current version of this document + at the time that they design PCI Express related components or platforms. See the PCI SIG website for + the most current version of this document. + + + + + PCI Express to PCI/PCI-X Bridge Specification + All designers are responsible for assuring that they use the most current version of this document at the + time that they design PCI Express related components or platforms. See the PCI SIG website for the most current + version of this document. + + + + + System Management BIOS (SMBIOS) Reference + Specification + + + + + (List Number Reserved for Compatibility) + + + + (List Number Reserved for Compatibility) + + + + (List Number Reserved for Compatibility) + + + + + IBM RS/6000® Division, Product Topology Data System, + Product Development Guide + Version 2.1 + + + + + Single Root I/O Virtualization and Sharing Specification + All designers are responsible for assuring that they use the most current version of this document at + the time that they design PCI Express SR-IOV related components or platforms. See the PCI SIG website + for the most current version of this document. + + + + + Multi-Root I/O Virtualization and Sharing Specification + All designers are responsible for assuring that they use the most current version of this document at the + time that they design PCI Express MR-IOV related components or platforms. See the PCI SIG website for the + most current version of this document. + + + + + + diff --git a/Platform/app_eeh_handling.xml b/Platform/app_eeh_handling.xml new file mode 100644 index 0000000..7bd39fb --- /dev/null +++ b/Platform/app_eeh_handling.xml @@ -0,0 +1,284 @@ + + + EEH Error Processing + + This appendix describes the architectural intent for EEH error processing. + This appendix does not attempt to illustrate all possible scenarios, and other + implementations are possible. + +
+ General Scenarios + In general, the device driver recovery consists of issuing an + ibm,read-slot-reset-state2 call prior to doing any recovery + to determine if (1) the IOA is in the MMIO Stopped and DMA Stopped state (that is, + that an error has occurred which has put it into this state), and (2) whether or + not the PE has been reset by the platform in the process of entering the MMIO + Stopped and DMA Stopped state, and then doing one of the following: + + + + Simplest approach: + + + Reset the PE + + + + Reconfigure the PE + + + + + + Most general approach (detailed more in ): + + + Release the PE for Load /Store + + + + Issue Load / Store instructions t + o get any desired state information from the IOA + + + + Call the ibm,slot-error-detail RTAS call to get the + platform error information + + + + Log the error information + + + + Reset the PE + + + + Reconfigure the PE + + + + + + Most robust (no reset unless necessary): + + + Release the PE for Load /Store + + + + Issue Load / Store instructions + to get any desired state information from the IOA + + + + Call the ibm,slot-error-detail RTAS call to get the + platform error information + + + + Log the error information + + + + Device driver does IOA cleanup + + + + Release the PE for DMA and restart operations (no reset) + + + + + + In any scenario, after several retries of a recoverable operation, the OS + may determine that further recovery efforts should cease. In such a case, + calling ibm,slot-error-detail with Function 2 + (Permanent Error), in addition to returning error information, marks that the PE is + no longer accessible due to previous errors. +
+ +
+ More Detail on the Most General Approach + The following gives a more detailed look at scenario # + in . This will be broken up into two groups of operations: + error logging and error recovery. + These scenarios assume that: + + + + The ibm,configure-pe RTAS call is implemented. + + + + The attempts at recovery stop when Max_Retries_Exceeded is true. + + + +
+ Error Logging + + + + If the device driver is going to capture internal IOA-specific information + as a part of the error logging process or if the IOA controlled by the device driver + requires a longer wait after reset than the normal PCI specified minimum wait time, + then the device driver determines whether its IOA has been reset as a result of entering + EEH Stopped State, by looking at the PE Recovery Info output of + the ibm,read-slot-reset-state2 RTAS call. + + + + The OS or device driver insures that all MMIOs to the IOA(s) in the PE are finished. + + + + If the IOA requires longer wait after reset times than the specified minimum, + and the PE was reset (see step #1) as a result of the EEH event, then wait the + additional necessary time before continuing. + + + + The OS or device driver + enables PE MMIOs by calling the ibm,set-eeh-option RTAS call + with Function 2. + + + + The OS or device driver calls the ibm,configure-pe RTAS call. + + + If the PCI fabric does not need configuring (the PE was not reset previous to the + call or was reset but was previously configured with ibm,configure-pe ), + then the call returns without doing anything, otherwise it attempts to configure + the fabric up to but not including the endpoint IOA configuration registers. + + + + If an EEH event occurs as a result of probing during the + ibm,configure-pe RTAS call that results in a + reset of the PE, the PE will be returned in the PE state of 2. Software + does not necessarily need to check this on return from the call. The case + where this occurs is expected to be rare, and probably signals a non-transient error. + In this case the software can continue on with the recovery phase of the EEH processing, + and will eventually hit the same EEH event on further processing. + + + + + + If the PE was + reset (see step #1) as a result of the EEH event, then if the device driver is + going to gather IOA-specific information for logging, it needs to finish the + configuration of the IOA PCI configuration registers, by restoring the PCI + configuration space registers of the IOA(s) in the PE (for example, BARs, + Memory Space Enable, etc.). + + + + If desired, the + device driver gathers IOA-specific information via MMIOs, by doing MMIOs to its IOA. + + + + The OS or device driver calls ibm,slot-error-detail . + Any data captured in step # is passed in the + call. Note that maximum amount of data will be captured in some cases only when the + ibm,slot-error-detail call is made with PE not in the MMIO Stopped + State (as it should be in step #). + + + If Max_Retries_Exceeded is true, then call ibm,slot-error-detail + with Function 2 (Permanent Error). + + + + If Max_Retries_Exceeded is not true, then call ibm,slot-error-detail + with Function 1(Temporary Error). + + + + + + The ibm,slot-error-detail RTAS call captures whatever + PCI config space registers it can between the configuration address passed in the call + and the system (PHB), and including at the configuration address and at the PHB, and + returns them along with the device specific data in an error log in the return information + from the call. This call may encounter another EEH event, in which case it returns what + information it can in the call, with a Status of 0 (Success). + + + + The OS or device driver logs the log entry returned from the + ibm,slot-error-detail RTAS call. + + + + If Max_Retries_Exceeded is not true, then the next step is PE Recovery, + otherwise stop and mark the IOA(s) in the PE as unusable. + + +
+ +
+ PE Recovery + + + + OS or device driver does a PE reset sequence. Note that this step is + required even if the PE was reset as a result of the initial EEH event, because + the error logging steps (for example, the ibm,configure-pe + or ibm,slot-error-detail calls) could have encountered + another EEH event. + + + The device driver or OS calls ibm,set-slot-reset with + Function 1 or 3 to activate the reset. + + + + The minimum reset active time is waited. + + + + The device driver or OS calls ibm,set-slot-reset with + Function 0 to deactivate the reset. + + + + The minimum reset inactive to first configuration cycles is waited. + If the IOA requires more than the standard PCI specified time, then wait that + longer time, instead. + + + + + + The OS or device driver calls ibm,configure-pe. + If an EEH event occurs as a result of probing + during the ibm,configure-pe RTAS call that results in a reset + of the PE, the PE will be returned in the PE state of 2. Software does not necessarily + need to check this on return from the call. The case where this occurs is expected to + be rare, and probably signals a non-transient error. In this case the software can + continue on with the recovery phase of the EEH processing, and will eventually hit + the same EEH event on further processing. + + + + + The device driver restores the PCI configuration spaces of the IOA(s) in the PE. + + + + The device driver initializes the IOA for operations. + + + +
+
+ diff --git a/Platform/app_glossary.xml b/Platform/app_glossary.xml new file mode 100644 index 0000000..0419382 --- /dev/null +++ b/Platform/app_glossary.xml @@ -0,0 +1,1289 @@ + + + + + Glossary + This glossary contains an alphabetical list of terms, phrases, and abbreviations used in this document. + + + + Term + Definition + + + + AC + Alternating current + + + + ACR + Architecture Change Request + + + + AD + Address Data line + + + + Adapter + A device which attaches a device to a bus or which converts one + bus to another; for example, an I/O Adapter (IOA), a PCI Host Bridge (PHB), + or a NUMA fabric attachment device. + + + + + addr + Address + + + + Architecture + The hardware/software interface definition or software module to + software module interface definition. + + + + ASCII + American National Standards Code for Information + Interchange + + + + ASR + Address Space Register + + + + BAT + Block Address Translation + + + + BE + Big-Endian or Branch Trace Enable bit in the + MSR (MSRBE) + + + + BIO + Bottom of Peripheral Input/Output Space + + + + BIOS + Basic Input/Output system + + + + BIST + Built in Self Test + + + + Boundedly undefined + Describes some addresses and registers which when referenced provide + one of a small set of predefined results. + + + + BPA + Bulk Power Assembly. Refers to components used for power distribution + from a central point in the rack. + + + + BPM + Bottom of Peripheral Memory + + + + BSCA + Bottom of System Control Area + + + + BSM + Bottom of System Memory + + + + BUID + Bus Unit Identifier. The high-order part of an interrupt source number + which is used for hardware routing purposes by the platform. + + + + CCIN + Custom Card Identification Number + + + + CD-ROM + Compact Disk Read-Only Memory + + + + CIS + Client Interface Service + + + + CMO + Cooperative Memory Over-commitment option. See + for more information. + + + + + + CMOS + Complimentary Metal Oxide Semiconductor + + + + Conventional PCI + Behavior or features that conform to . + + + + CPU + Central Processing Unit + + + + CR + Condition Register + + + + CTR + Count Register + + + + DABR + Data Address Breakpoint Register + + + + DAR + Data Address Register + + + + DASD + Direct Access Storage Device (a synonym for “hard disk”) + + + + DBAT + Data Block Address Translation + + + + DC + Direct current + + + + DEC + Decrementer + + + + DIMM + Dual In-line Memory Module + + + + DMA + Direct Memory Access + + + + DMA Read + A data transfer from System Memory to I/O. A DMA Read Request + is the inbound operation and the DMA Read Reply (or Read Completion) is the + outbound data coming back from a DMA Read Request. + + + + DMA Write + A data transfer to System Memory from I/O or a Message Signalled Interrupt (MSI) DMA Write. This is an inbound operation. + + + + DOS + Disk OS + + + + DR + Data Relocate bit in MSR (MSRDR) + + + + DRA + Deviation Risk Assessment + + + + DRAM + Dynamic Random Access Memory + + + + DRC + Delayed Read Completion. A transaction that has completed + on the destination bus and is now moving toward the originating bus to complete. + DR Connector. + + + + DR entity + An entity that can participate in DR operations. That is, an entity + that can be added or removed from the platform while the platform power is on and the + system remains operational. + + + + DRR + Delayed Read Request. A transaction that must complete on the destination bus before completing on the originating bus. + + + + DSISR + Data Storage Interrupt Status Register + + + + DWR + Delayed Write Request. A transaction that must complete on the destination bus before completing on the originating bus. + + + + EA + Effective Address + + + + EAR + External Access Register + + + + ECC + Error Checking and Correction + + + + EE + External interrupt Enable bit in the MSR (MSREE) + + + + EEH + Enhance I/O Error Handling + + + + EEPROM + Electrically Erasable Programmable Read Only Memory + + + + EPOW + Environment and Power Warning + + + + + Error Log indicator An amber indicator that indicates that the user needs to + look at the error log or problem determination procedures, in order to determine the cause. + Previously called System Information (Attention). + + + + FCode + A computer programming language defined by the OF standard which is semantically + similar to the Forth programming language, but is encoded as a sequence of binary byte codes + representing a defined set of Forth words. + + + + FE0 + Floating-point Exception mode 0 bit in the MSR (MSRFE0) + + + + FE1 + Floating-point Exception mode 1bit in the MSR (MSRFE1) + + + + FIR + Fault Isolation Registers + + + + FLR + Function Level Reset (see PCI Express documentation). An optional reset for PCI Express + functions that allows resetting a single function of a multi-function IOA. + + + + FP + Floating-Point available bit in the MSR (MSRFP) + + + + FPSCR + Floating-Point Status And Control Register + + + + FRU + Field Replaceable Unit + + + + FSM + Finite State Machine + + + + GB + Gigabytes - as used in this document it is 2 raised to the power of 30 + + + + HB + Host Bridge + + + + HMC + Hardware Management Console - used generically to refer to the system + component that performs platform administration function where ever physically located. + The HMC is outside of this architecture and may be implemented in multiple ways. + Examples include: a special HMC applications in another system, an external appliance, + or in an LPAR partition using the Virtual Management Channel (VMC) interface to the + hypervisor. + + + + Hz + Hertz + + + + IBAT + Instruction block address translation + + + + ID + Identification + + + + IDE + Integrated Device Electronics + + + + IDU + Interrupt Delivery Unit + + + + IEEE + Institute of Electrical and Electronics Engineers + + + + I2C + Inter Integrated-circuit Communications + + + + I/O + nput/Output + + + + I/O bus master + Any entity other than a processor, cache, + memory controller, or host bridge which supplies both address and data in + write transactions or supplies the address and is the sink for the data in + read transactions. + + + + I/O device + Generally refers to any entity that is connected + to an IOA (usually through a cable), but in some cases may refer to the IOA + itself (that is, a device in the device tree that happens to be used for I/O + operations). + + + + I/O Drawer + An enclosure in a rack that holds at least one PHB and at + least one IOA. + + + + ILE + Interrupt Little-Endian bit in MSR (MSRILE) + + + + Instr + Instruction + + + + Interrupt Number + See Interrupt Vector below. + + + + Interrupt Vector + The identifier associated with a specific interrupt source. + The identifier’s value is loaded into the source’s Interrupt Vector Register and + is read from the Interrupt Delivery Unit’s Interrupt Acknowledge Register. + + + + IOA + I/O Adapter. A device which attaches to a physical bus which is capable + of supporting I/O (a physical IOA) or logical bus (a virtual IOA). The term “IOA” + without the usage of the qualifier “physical” or “virtual” will be + used to designate a physical IOA. Virtual IOAs are defined further in + + . + In PCI terms, an IOA may be defined by a unique combination of its assigned + bus number and device number, but not necessarily including its function number. + That is, an IOA may be a single or multi-function device, unless otherwise specified by + the context of the text. In the context of a PCIe I/O Virtualized (IOV) device (not to be + confused with a virtual IOA), an IOA is a single or multiple function device (for example, a + PCIe Virtual Function (VF) or multiple VFs). An IOA function may or may not have its own set of + resources, that is may or may not be in its own Partitionable Endpoint (PE) domain + (see also + ). + + + + + IOA function + That part of an IOA that deals with a specific part of the + IOA as defined by the configuration space “Function” part of Bus/Device/Function. + For single-function IOAs, the IOA Function and the IOA are synonymous. + + + + IP + Interrupt Prefix bit in MSR (MSRIP) + + + + IPI + Interprocessor Interrupt + + + + IR + Instruction Relocate bit in MSR register (MSRIR) or infrared + + + + ISF + Interrupt 64-bit processor mode bit in the MSR (MSRISF) + + + + ISO + International Standards Organization + + + + ISR + Interrupt Source Register + + + + ISU + Interrupt Source Unit + + + + KB + Kilobytes - as used in this document it is 2 raised to the power of 10 + + + + KHz + Kilo Hertz + + + + LAN + Local Area Network + + + + LCD + Liquid Crystal Display + + + + LE + Little-Endian bit in MSR (MSRLE) or Little-Endian + + + + LED + Light Emitting Diode + + + + LMB + Logical Memory Block. The Block of logical memory addresses associated with a dynamically + reconfigurable memory node. + + + + Load + A Load Request is the outbound (from the processor) operation + and the Load Reply is the inbound data coming back from a + Load Request. When it relates to I/O operations, this is an + MMIO Load . + + + + LR + Link Register + + + + LSb + Least Significant bit + + + + LSB + Least Significant Byte + + + + LSI + Level Sensitive Interrupt + + + + LUN + Logical Unit Number + + + + L1 + Primary cache + + + + L2 + Secondary cache + + + + MB + Megabytes - as used in this document it is 2 raised to the power of 20 + + + + ME + Machine check Enable + + + + MMIO + Memory Mapped I/O. This refers to the mapping of the address space required + by an I/O device for Load or Store operations into + the system’s address space. + + + + MES + Miscellaneous Equipment Specification + + + + MFM + Modified frequency modulation + + + + MHz + Mega Hertz + + + + MOD + Address modification bit in the MSR + (MSRMOD) + + + + MP + Multiprocessor + + + + MSb + Most Significant bit + + + + MSB + Most Significant Byte + + + + MSI + Message Signalled Interrupt + + + + MSR + Machine State Register + + + + MTT + Multi-TCE-Table option. See + + + . + + + + + N/A + Not Applicable + + + + Nibble + Refers to the first or last four bits in an 8 bit byte + + + + NUMA + Non-Uniform Memory Access + + + + NUMA fabric + Mechanism and method for connecting the multiple nodes of a NUMA system + + + + NVRAM + Nonvolatile Random Access Memory + + + + OF + Open Firmware + + + + OP + Operator + + + + OS + Operating System + + + + OUI + Organizationally Unique Identifier + + + + PA + Processor Architecture + + + + PAP + Privileged Access Password + + + + LoPAR + Used within the Linux on Power Architecture + Reference documents to denote: (1) the architectural requirements specified + by the Linux on Power Architecture Reference document, (2) the Linux on Power Architecture + Reference documents themself, and (3) as an adjective to qualify an entity as being + related to this architecture. + + + + Partitionable Endpoint + This refers to the I/O granule that may be treated as one for + purposes of assignment to an OS (for example, to an LPAR partition). May be an + I/O adapter (IOA), or groups of IOAs and bridges, or portions of IOAs. PE granularity + supported by the hardware may be finer than is supported by the firmware. Grouping + of multiple PEs into one DR entity may limit assignment of a the separate PEs to different + LPAR partitions. See also DR entity. + + + + PC + Personal Computer + + + + PCI + Peripheral Component Interconnect. An all-encompassing term referring to + conventional PCI, PCI-X, and PCI Express. + + + + PCI bus + A general term referring to either the PCI Local Bus, as + specified in and + for conventional PCI and PCI-X, or a PCI Express link, as specified in + for PCI Express. + + + + PCI Express + Behavior or features that conform to + . + + + + PCI link + A PCI Express link, as specified in . + + + + PCI-X + Behavior or features that conform to . + + + + PD + Presence Detect + + + + PE + When referring to the body of the LoPAR, this refers to a Partitionable + Endpoint. + + + + + + + PEM + Partition Energy Management option. See + + + . + + + + + Peripheral I/O Space + The range of real addresses which are assigned + to the I/O Space of a Host Bridge (HB) and which are sufficient to contain all of + the Load and Store address space requirements of all the devices in the I/O Space + of the I/O bus that is generated by the HB. A keyboard controller is an example of + a device which may require Peripheral I/O Space addresses. + + + + Peripheral Memory Space + The range of real addresses which are assigned to the Memory + Space of a Host Bridge (HB) and which are sufficient to contain all of the Load and + Store address space requirements of the devices in the Memory Space of the I/O bus + that is generated by the HB. The frame buffer of a graphics adapter is an example + of a device which may require Peripheral Memory Space addresses. + + + + Peripheral Space + Refers to the physical address space which may + be accessed by a processor, but which is controlled by a host bridge. At least one + peripheral space must be present and it is referred to by the suffix 0. A host bridge + will typically provide access to at least a memory space and possibly to an I/O + space. + + + + PHB + PCI Host Bridge + + + + PIC + Programmable Interrupt Controller + + + + PIR + Processor Identification Register + + + + Platform + Refers to the hardware plus firmware portion of a system composed of hardware, + firmware, and OS. + + + + Platform firmware + Refers to all firmware on a system including the software or firmware in a + support processor. + + + + Plug-in I/O card + A card which can be plugged into an I/O + connector in a platform and which contains one or more IOAs and potentially + one or more I/O bridges or switches. + + + + Plug-in Card + An entity that plugs into a physical slot. + + + + PMW + Posted memory write. A transaction that has complete on the + originating bus before completing on the destination bus + + + + PnP + Plug and Play + + + + POP + Power On Password + + + + POST + Power-On Self Test + + + + PR + Privileged bit in the MSR (MSRPR) + + + + Processor Architecture + Used throughout this document to + mean compliance with the requirements specified in + . + + + + Processor revision number + A 16-bit number that distinguishes between various releases + of a particular processor version, for example different engineering change + levels. + + + + PVN + Processor Version Number. Uniquely determines the particular + processor and PA version. + + + + PVR + Processor Version Register. A register in each processor + that identifies its type. The contents of the PVR include the processor + version number and processor revision number. + + + + RAID + Redundant Array of Independent Disks + + + + RAM + Random Access Memory + + + + RAS + Reliability, Availability, and Serviceability + + + + Real address + A real address results from doing address + translation on an effective address when address translation is enabled. + If address translation is not enabled, the real address is the same as the + effective address. An attempt to fetch from, load from, or store to a real + address that is not physically present in the machine may result in a + machine check interrupt. + + + + Reserved + The term “reserved” is used within this + document to refer to bits in registers or areas in the address space + which should not be referenced by software except as described in this + document. + + + + Reserved for firmware use + Refers to a given location or bit which may not be used by + software, but are used by firmware. + + + + Reserved for future use + Refers to areas of address space or bits in registers which may be + used by future versions of this architecture. + + + + RI + Recoverable interrupt bit in the MSR (MSRRI) + + + + RISC + Reduced Instruction Set Computing + + + + RMA + Real Mode Area. The first block of logical memory addresses + owned by a logical partition, containing the storage that may be accessed with + translate off. + + + + ROM + Read Only Memory + + + + Root Complex + A PCI Express root complex as specified in + . + + + + RPN + Real Page Number + + + + RTAS + Run-Time Abstraction Services + + + + RTC + Real Time Clock + + + + SAE + Log Service Action Event log + + + + SCC + Serial Communications Controller + + + + SCSI + Small Computer System Interface + + + + SE + Single-step trace enabled bit in the MSR + (MSRSE) + + + + Service Focal Point + The common point of control in the system for handling all + service actions + + + + Serviceable Event + Serviceable Events are platform, + global, regional and local error events that require a service action + and possibly a call home when the serviceable event must be handled by a + service representative or at least reported to the service provider. + Activation of the Error Log indicator notifies the customer of the event + and the event indicates to the customer that there must be some intervention + to rectify the problem. The intervention may be a service action that the + customer can perform or it may require a service provider. + + + + SES + Storage Enclosure Services (can also mean SCSI Enclosure + Services in relation to SCSI storage) + + + + SF + Processor 32-bit or 64-bit processor mode bit in the MSR + (MSRSF) + + + + SFP + Service Focal Point + + + + Shrink-wrap OS + A single version of an OS that runs on all + compliant platforms. + + + + Shrink-wrap Application + A single version of an application program + that runs on all compliant platforms with the applicable OS. + + + + SMP + Symmetric multiprocessor + + + + SMS + System Management Services + + + + Snarf + An industry colloquialism for cache-to-cache + transfer. A typical scenario is as follows: (1) cache miss from cache A, + (2) line found modified in cache B, (3) cache B performs castout of modified + line, and (4) cache A allocates the modified line as it is being written back + to memory. + + + + Snoop + The act of interrogating a cache for the presence of a + line, usually in response to another party on a shared bus attempting to + allocate that line. + + + + SPRG + Special Purpose Registers for General use + + + + SR + System Registers + + + + SRC + Service Reference Code + + + + SRN + Service Request Number + + + + Store + A Store Request is an + outbound (from the processor) operation. When it relates to I/O + operations, this is an MMIO Store. + + + + System + Refers to the collection of hardware, system firmware, + and OS software which comprise a computer model. + + + + System address space + The total range of addressability as established by the + processor implementation. + + + + System Control Area + Refers to a range of addresses which + contains the system ROM(s) and an unarchitected, reserved, platform-dependent + area used by firmware and Run-Time Abstraction services for control of the + platform. The ROM areas are defined by the OF properties in the + openprom and os-rom nodes + of the OF device tree. + + + + System Information (Attention) indicator + See Error Log indicator. + + + + System firmware + Refers to the collection of all firmware on a system + including OF, RTAS and any legacy firmware. + + + + System Memory + Refers to those areas of memory which form + a coherency domain with respect to the PA processor or processors that + execute application software on a system. + + + + System software + Refers to the combination of OS software, + device driver software, and any hardware abstraction software, but + excludes the application software. + + + + TB + Time Base + + + + TCE + Translation Control Entry + + + + TLB + Translation Look-aside Buffer + + + + TOD + Time Of Day + + + + TOSM + Top of system memory + + + + TPM + Top of Peripheral Memory + Trusted Platform Module + + + + tty + Teletypewriter or ASCII character driven + terminal device + + + + UI + User Interface + + + + USB + Universal Serial Bus + + + + v + Volt + + + + VGA + Video Graphics Array + + + + VMC + Virtual Management Channel + + + + VPD + Vital Product Data + + + + VPNH + Virtual Processor Home Node option. See + + + . + + + + + + + + + + + + + + diff --git a/Platform/bk_main.xml b/Platform/bk_main.xml new file mode 100644 index 0000000..5a2b72c --- /dev/null +++ b/Platform/bk_main.xml @@ -0,0 +1,121 @@ + + + + + + + Platform + Linux on Power Architecture Reference + + + + + System Software Work Group + + syssw-chair@openpowerfoundation.org + + OpenPOWER Foundation + + + + 2016 + OpenPOWER Foundation + + + Revision 2.0_pre1 + OpenPOWER + + + + + + Copyright details are filled in by the template. + + + + + + The purpose of this document is to provide firmware and software + architectural details for the base Platform hardware associated with an OpenPOWER Systems. + The base content for this document were contributed to the OpenPOWER Foundation in the + IBM Linux on Power Architecture Platform Reference (LoPAPR) Draft + document. It had numerous contributors inside IBM. + This document is a Standard Track, Work Group Specification work product owned by the + System Software Workgroup and handled in compliance with the requirements outlined in the + OpenPOWER Foundation Work Group (WG) Process document. It was + created using the Master Template Guide version 0.9.5. Comments, + questions, etc. can be submitted to the public mailing list for this document at + TBD. + + + + + + 2016-05-04 + + + + Revision 2.0_pre1 - initial conversion from IBM document. Extracted from + Linux on Power Architecture Platform Reference (LoPAPR) version 1.1 dated March 24, + 2016 -- Chapter 1 (Introduction), Chapter 2 (System Requirements), + Chapter 3 (Address Map), Chapter 4 (I/O Bridges and Topology), + Chapter 5 (Processors and Memory), Chapter 6 (Interrupt Controller), + Chapter 8 (Non-volatile memory), Chapter 9 (I/O Devices), + Chapter 11 (The Symmetric Multiprocessor Option), Chapter 12 (Product Topology), + and Appendix H (Non-Uniform Memory Access [NUMA] Option). + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + diff --git a/Platform/ch_address_map.xml b/Platform/ch_address_map.xml new file mode 100644 index 0000000..333f6ce --- /dev/null +++ b/Platform/ch_address_map.xml @@ -0,0 +1,1132 @@ + + + 3 Address Map + + The address map of an LoPAR platform is made up of several distinct + areas. These areas are one of five basic types. Each of these types has its own + general characteristics such as coherency, alignment, size restrictions, + variability of starting address and size, the system action on access of the + area, and so on. This chapter gives details on some of those characteristics, + and other chapters define the other characteristics. The variable + characteristics of these areas are reported to the OS via properties in the OF + device tree. + +
+ Address Areas + The following is a definition of the five areas and some of their + characteristics: + + + + System Memory refers to memory + which forms a coherency domain with respect + to the PA processor(s) that execute application software on a system. See + for details on aspects of coherence. + System Memory Spaces refer to one or more pieces that + together form the System Memory. System Memory areas may be marked with a + special value of the “status” property of + “reserved” which means that this memory is not for general use by + the base OS, but may be reserved for use by OS extensions (see + ). Some System Memory areas may be + preservable across boots (see ). + + + + Peripheral Memory Space refers to a range of real addresses which + are assigned to the Memory Space of a Host Bridge (HB) or System Bus attached + IOA, and which are sufficient to contain all of the Load and Store address + space requirements of all IOAs in the Memory Space of the I/O bus that is + generated by the HB or which are encompassed by the System Bus attached IOA. + The frame buffer of a graphics IOA is an example of a device which may reside + in the Peripheral Memory Space. Due to space limitations in the address space + below 4 GB, the HBs of platforms may split this space into two pieces; one to + support the IOAs that need to have their addresses below 4 GB (because they + only support 32-bit addresses) and another to support the IOAs that can have + their addresses above 4 GB (because they support 64-bit addresses). In addition + to a Memory Space, many types of I/O buses have a separate address space called + the I/O Space. An HB which generates such I/O buses must decode another address + range, the Peripheral I/O Space.A + peripheral space may also include a “configuration” address + space. The configuration space is abstracted by a Run-Time Abstraction Service + (for example, see ). + + + + Peripheral I/O Space refers to a range of real addresses which + are assigned to the I/O Space of an HB or System Bus attached IOA and which are + sufficient to contain all of the Load and Store address space requirements of + all the IOAs in the I/O Space of the I/O bus that is generated by the HB or + which are encompassed by the System Bus IOA. A keyboard controller is an + example of an IOA which may require Peripheral I/O Space addresses. + + + + System Control Area (SCA) refers to a range of addresses which + contains all reserved addresses (architected or unarchitected) which are not + part of one of the other defined address spaces. For example, the system ROM(s), + unarchitected platform-dependent addresses used by firmware and Run-Time + Abstraction Services for control of the platform, and architected entities like + interrupt controller addresses when those addresses are not in another defined + address space. + + + + Undefined refers to areas that are not one of the above four + areas. The result of accessing one of these areas is defined in as an invalid address error. + + + + In addition to the above definitions, it is convenient, relative to + I/O op erations, to define a Partitionable Endpoint. A Partitionable + Endpoint (PE) is an I/O subtree that can be treated as a unit for + the purposes of partitioning and error recovery. A PE may be a single or + multi-function IOA, a function of a multi-function IOA, or multiple IOAs + (possibly including switch and bridge structures above the multiple IOAs). See + for more information about PEs. + In describing the characteristics of these various areas, it is + convenient to have a nomenclature for the various boundary addresses. + defines the labels which are used in this + document when describing the various address ranges. Note that + “bottom” refers to the smallest address of the range and + “top” refers to the largest address. + + + Map Legend + + + + + + + + Label + + + + + Description + + + + + + + + BIOn + + + Bottom of Peripheral I/O Space for HBn (n=0, 1, 2,...). + The OF property “ranges” + in the OF device tree for HBn contains the value of BIOn. + + + + + TIOn + + + Top of Peripheral I/O Space for HBn (n=0, 1, 2,...). The + value of TIOn can be determined by adding the size of the area as found in the + OF property “ranges” in the OF device tree + for HBn to the value of BIOn found in that same property and then subtracting + 1. + This architecture allows at most one Peripheral I/O area + per HB which may be above or below 4 GB. For any given n, BIOn to TIOn cannot + span from the first 4 GB of address space to the second. + + + + + BPMn,m + + + Bottom of Peripheral Memory Space m (m=0,1) for HBn (n=0, + 1, 2,...), as viewed from the system side of HBn. The OF property + “ranges” in the OF device tree for HBn contains the + value of BPMn,m. + + + + + BPM’n,m + + + Bottom of Peripheral Memory Space m (m=0,1) for HBn (n=0, + 1, 2,...), as viewed from the I/O side of the HBn. That is, this is the value + to which BPMn,m gets translated to as it passes through the HB. The OF property + “ranges” in the OF device tree for HBn + contains the value of BPM’n,m. BPM’n,m may be equal to BPMn,m or + may not be. + + + + + TPMn,m + + + Top of Peripheral Memory Space m (m=0,1) for HBn (n=0, 1, + 2,...) as viewed from the system side of HBn. The Peripheral Memory Space + address range is in the OF device tree, as indicated by the + “ranges” property in the node in the OF device tree + for HBn; BPMn,m to TPMn,m. The value of TPMn,m can be determined by adding the + size of the area as found in the OF property + “ranges” in the OF device tree for HBn to the value of + BPMn,m found in that same property and then subtracting 1. + This architecture allows for one or two Peripheral Memory + areas per HB (hence, m=0,1). A Peripheral Memory area may be above 4 GB or + below. For any given n, BPMn,m to TPMn,m cannot span from the first 4 GB of + address space to the second. + + + + + TPM’n,m + + + Top of Peripheral Memory Space m (m=0,1) for HBn (n=0, 1, + 2,...) as viewed from the I/O side of HBn. The value of TPM’n,m can be + calculated from the values in the“ranges” + property as was TPMn,m. In some cases TPM’n,m is required to be equal to + TPMn,m and in some cases it is not required to be equal. For any given n, + BPM’n,m to TPM’n,m cannot span from the first 4 GB of address + space to the second. + + + + + BSCAn + + + Bottom of System Control Area. Corresponding top of the + System Control Area is TSCAn. This architecture allows for one or two SCAs per + platform. The SCA below 4 GB is at the top (largest addresses) of the lower 4 + GB range. + + + + + TSCAn + + + Top of System Control Area. For any given n, BSCAn to + TSCAn cannot span from the first 4 GB of address space to the second. + + + + + BSMn + + + Bottom of System Memory Space n (n=0, 1, 2,...); BSM0 = 0. + The OF property “reg” in the OF device tree + for the Memory Controller’s node contains the value of BSMn. + + + + + TSMn + + + Top of System Memory Space n (n=0, 1, 2,...). The value of + TSMn can be determined by adding the value of BSMn as found in the Memory + Controller’s node of the OF device tree to the value of the size of that + area as found in the same property, and then subtracting 1. + + + + + BTTAn,m + + + Bottom of TCE Translatable Address space m (m=0, 1, 2,...) + for HBn (n=0, 1, 2,...) as viewed from the I/O side of HBn. This is the bottom + of an address range that is translatable by a Translation Control Entry (TCE) + table. The value of BTTAn,m is obtained from the + “ibm,dma-window” or + “ibm,my-dma-window” property in the OF device + tree. + + + + + TTTAn,m + + + Top of TCE Translatable Address space m (m=0, 1, 2,...) + for HBn (n=0, 1, 2,...) as viewed from the I/O side of HBn. This is the top of + an address range that is translatable by a TCE table. The range BTTAn,m to + TTTAn,m is not accessible by more than one PE for any given “n”. + The value of TTTAn,m can be determined by adding the size of the area as found + in the OF property “ibm,dma-window” or + “ibm,my-dma-window” in the OF device tree + for HBn to the value of BTTAn,m found in that same property and then + subtracting 1. + + + + +
+ The figures found in , show + examples of the areas referenced by the labels in . + The OS and other software should not use fixed addresses for these + various areas. A given platform may, however, make some of these addresses + unchangeable. Each of these areas is defined in the OF device tree in the node + of the appropriate controller. This gives platforms the most flexibility in + implementing the System Address Map to meet their market requirements. + + + + R2--1. + + All unavailable addresses in the Peripheral Memory and Peripheral + I/O Spaces must be conveyed in the OF device tree. + + + + A “device_type” of + “reserved” must be used to specify areas which are not + to be used by software and not otherwise reported by OF. + + + + Shadow aliases must be communicated as specified by the + appropriate OF bus binding. + + + + + + + R2--2. + + There must not be any address generated by + the system which causes the system to hang. + + + + + Hardware Implementation Note: The reason for Requirement + is to reserve address space for registers + used only by the firmware or addresses which are used only by the + hardware. +
+ +
+ Address Decoding (or Validating) and Translation + In general, different components in the hardware are going to decode + the address ranges for the various areas. In some cases the component may be + required to translate the address to a new address as it passes through the + component. The requirements, below, describe the various system address decodes + (or validating) and, where appropriate, what address transforms take place + outside of the processor. + The HB requirements in this section refer to HBs which are defined by + this architecture. Currently, there is only one HB defined by this + architecture, and that is the PHB. HBs which implement I/O buses other than + those defined by this architecture may or may not require changes to this + addressing model. + The reader may want to reference the example address maps found in + , while reading through the + requirements of this section. + +
+ <emphasis>Load</emphasis> and <emphasis>Store</emphasis> + Address Decoding and Translation + + Load and Store + operations may be targeted at System Memory or I/O. The latter is called Memory + Mapped I/O (MMIO). + + + + R2--1. + + Processor Load and Store + operations must be routed and translated as shown in . + + + + + + Processor Bus Address Space Decoding and Translation + + + + + + + + + Address Range at Processor + Bus + + + + + Route and Translation + Requirements + + + + + Other Requirements and + Comments + + + + + + + + BSCAn to TSCAn + (n=0, 1) + + + To ROM controller or to a platform dependent area. + Translation dependent on implementation. + + + Areas other than ROM are reserved for firmware use, or + have their address passed by the OF device tree. + + + + + BIOn to TIOn + (n=0,1, 2,...) + + + Send through the HB to the I/O space of the I/O bus, + translating by subtracting the value of BIO from each address in this range + (that is, translate BIO to TIO to be at 0 to (TIO - BIO) on the I/O + side). + + +   + + + + + BPMn,m to TPMn,m + (n=0, 1, 2,...) + (m=0, 1) + + + Send through HBn to the Memory Space of the I/O bus. + + + If BPMn,m < 4 GB, do not translate an address in the + BPMn,m to TPMn,m range as the transaction passes through the bridge (that is, + BPM’n,m = BPMn,m and TPM’n,m = TPMn,m). + + + + If BPMn,m is at or above 4 GB then if BPM’n,m is + to be below 4 GB (for 32-bit IOAs) then translate addresses in the BPMn,m to + TPMn,m range so that this address range becomes BPM’n,m to + TPM’n,m (where BPM’n,m and TPM’n,m are less than 4 GB) as + the transaction passes through the bridge, otherwise do not translate an + address in the BPMn,m to TPMn,m range as the transaction passes through the + bridge (for 64-bit IOAs which are configured at or above 4 GB). + + + + + Platforms that need to support both 32-bit capable and + 64-bit capable IOAs and do not want to configure the 64-bit capable IOAs below + 4 GB need to support two Peripheral Memory spaces per HB. + + + + + BSMm to TSMm + (m>0) + + + To System Memory Space m, no translation. + + + Can be at or above 4 GB, or below BSCA0. + + + + + 0 to TSM0 + + + To System Memory Space 0, no translation + + +   + + + + + All other addresses + + + See . + + + Access is to undefined space. + + + + +
+ + + + R2--2. + + There must be no architected address + spaces (Peripheral Memory, Peripheral I/O, SCA, or System Memory) which span + the (4GB - 1) to 4 GB boundary. + + + + + R2--3. + + The following are the System Control Area requirements: + + + + The platform must have at most one System Control Area below 4 GB + and at most one per platform or per NUMA node at or above 4 GB. + + + + The System Control Area must not overlap with the System Memory + Space(s), Peripheral Memory Space(s), or the Peripheral I/O Space(s) in the + platform. + + + + + + + R2--4. + + The following are the System Memory Space requirements: + + + + Each platform must have at least one System Memory Space. + + + + The System Memory Space(s) must not overlap with the Peripheral I/O + Space(s), Peripheral Memory Space(s), the System Control Area, or other System + Memory Space(s) in the platform. + + + + The first System Memory Space must start at address 0 (BSM0 = 0), + must be at least 128 MB before a second System Memory Space is added and must + be contiguous. + + + + Each of the additional (optional) System Memory Space(s) + must start on a 4 KB boundary. + + + + Each of the additional (optional) System Memory Space(s) + must be contiguous within itself. + + + + There must be at most eight System Memory Spaces below BSCA0 and + at most eight at or above 4 GB. + + + + If multiple System Memory Spaces exist below 4 GB, then they + must not have any Peripheral Memory or Peripheral I/O Spaces interspersed + between them and if multiple System Memory Spaces exist above 4 GB, then they + must not have any Peripheral Memory or Peripheral I/O Spaces interspersed + between them. + + + + + + + R2--5. + + The following are the Peripheral Memory Space requirements: + + + + The Peripheral Memory Space(s) must not overlap with the System + Memory Space(s), Peripheral I/O Space(s), the System Control Area, or other + Peripheral Memory Space(s) in the platform. + + + + The size of each + Peripheral Memory Space (TPMn,m - BPMn,m + 1) must be a power of two for sizes + up to and including 256 MB, with the minimum size being 1 MB, and an integer + multiple of 256 MB plus a power of two which is greater than or equal to 1 MB + for sizes greater than 256 MB (for example, 1 MB, 2 MB, 4 MB, 8 MB, 16 MB, 32 + MB, 64 MB, 128 MB, 256 MB, (256 + 1) MB, (256 + 2) MB,..., (512 + 1) + MB,...). + + + + The boundary alignment for each Peripheral Memory Space must be an integer multiple + of the size of the space up to and including 256 MB and must be an integer + multiple of 256 MB for sizes greater than 256 MB. + + + + There must be at most two Peripheral Memory Spaces per HB. + + + + + If the Peripheral Memory Space for a HB is below 4 GB, then the + address must not be translated as it passes through the HB from the system side + to the I/O side of the HB (see ). + + + + If the Peripheral Memory Space for a HB is above 4 GB, then the + address may or may not be translated as it passes through the HB from the + system side to the I/O side of the HB, but if it is translated, then the + translated address range must be aligned on a boundary which is an integer + multiple of the size of the Peripheral Memory Space. + + + + + + + Implementation Note: Relative to Requirement + , not all OSs can support BPM’ to + TPM’ being above 4 GB. + + + + R2--6. + + The following are the Peripheral I/O Space requirements: + + + + The Peripheral I/O Space(s) must not overlap with the System + Memory Space(s), Peripheral Memory Space(s), the System Control Area, or other + Peripheral I/O Space(s) in the platform. + + + + The size of each Peripheral I/O Space (TIOn - BIOn + 1) must be a + power of two with the minimum size being 64 KB (that is, sizes of 64 KB, 128 + KB, 256 KB, 512 KB, 1 MB, 2 MB, 4 MB, 8 MB, 16 MB, 32 MB, 64 MB, and so on, are + acceptable). + + + + The boundary alignment for each Peripheral I/O Space must be an integer multiple of the size of + the space. + + + + There must be at most one Peripheral I/O Space per + HB. + + + + + + + R2--7. + + All System Memory must be + accessible via DMA operation from all IOAs in the system, except where LPAR + requirements limit accessibility of an IOA belonging to one partition to the + System Memory of another partition. + + + + + Hardware Implementation Notes: Memory controller and memory card + designers who are designing for 64-bit platforms should be careful to consider + that the amount of I/O space below 4 GB is reduced by the amount of System + Memory space below 4 GB. Therefore it may be prudent to design the hardware to + allow minimization of the amount of System Memory below 4 GB, in order to allow + maximization of the space for 32-bit Peripheral Memory and Peripheral I/O + spaces below 4 GB. + The beginning addresses and sizes of the Peripheral I/O Space(s) + and Peripheral + Memory Space(s), are controlled by firmware. Information about the address map + is reported by the OF Device Tree or, for items that can change, through RTAS + calls (for example, for Dynamic Reconfiguration, through the + ibm,configure-connector RTAS call). + Certain System Memory addresses must be reserved in all systems for + specific uses (see and for more information). +
+
+ DMA Address Validation and Translation + is a representation of + how the validation and translation mechanism works, along with a description of + the steps which are involved. At the core of the translation mechanism is the + Translation and Control Entry (TCE) table. + +
+ PE DMA Address Validation and Translation in the Platform + + + + + + + + +
+ +
+ DMA Addressing Requirements + + + + R2--1. + + Upon receiving a DMA + transaction to the Memory Space of an I/O bus, the HB must perform the + validation and translation steps, as indicated in + and in + . + + + + + + DMA Address Decoding and Translation (I/O Bus Memory + Space) + + + + + + + + + Address Range at I/O Side of + HBn + + + + + Route and Translation + Requirements + + + + + Other Requirements and + Comments + + + + + + + + BPM’n,m to TPM’n,m + (n=0, 1, 2,...) + (m=0, 1) + (note 1) + + + HB does not respond or responds and signals an invalid + address error (See ). + + +   + + + + + BTTAn,m to TTTAn,m + (n=0, 1, 2,...) + (m=0, 1, 2,...) + (note 1) + + + If the PE that is trying to access this space is allowed + to access this space, then translate via the TCE table (as specified in ) and pass the translated address through + the HB, otherwise generate an invalid address or TCE extent error, as + appropriate (See ). + + + See Notes 2, 3 + + + + + All other addresses + + + Generate an invalid address error (See ). + + + See Note 3 + + + + + Notes: + + + n = # of HB Viewing or Receiving the Operation, m = # + of instance within the HB. + + + + After translation of the address, if the translated + address would re-access the same HB or another HB (for example, is in the + Peripheral Memory Space or Peripheral I/O Space of that HB or another HB), then + the HB generates an invalid address error (See ). + + + + If the Enhanced I/O Error Handling (EEH) option is + implemented and enabled, then on an error, the PE will enter the DMA Stopped + State (See ). + + + + + + + +
+ + + + R2--2. + + An HB must not act as a target + for operations in the I/O Space of an I/O bus. + + + +
+
+ DMA Address Translation and Control via the TCE + Mechanism + This architecture defines a Translation and Control Entry (TCE) + mechanism for translating and controlling DMA addresses. There are several + reasons for doing such translations, including: + + + + To provide a mechanism for increasing the number of addressing + bits for some IOAs. For example, IOAs which are only capable of accessing up to + 4 GB via DMA need a way to access above that limit when used in 64-bit + addressing systems and the addressing requirements go beyond 4 GB. + + + + To provide a redirection mechanism. A redirection mechanism is + needed, even for 64-bit addressing capable IOAs, in order to provide the + protection and indirection benefits provided by such a translation. + + + + The description of how the access to the TCE table occurs, for the + translation of a 32-bit address and using a 4 KB I/O page size, follows. The + most significant 20 bits of the address (for example, AD[31:12], for PCI) is + used as an offset into the TCE table for the PE to select the TCE. Thus, the + first TCE maps the addresses BTTAn to BTTAn + 0x00000FFF of the Memory Space of + the I/O bus; the second entry controls translation of addresses BTTAn + + 0x00001000 to BTTAn + 0x00001FFF, and so on. The translated real system address + is generated as follows. The Real Page Number (RPN) from the TCE replaces the + 20 most significant bits of the address from the I/O bus. The least significant + 12 bits from the I/O bus address are used as-is for the least significant 12 + bits of the new address. + Thus, the TCE table entries have a one-to-one correspondence with + the first n pages of the Memory Space of the I/O bus starting at BTTAn that + corresponds to the TCE table. The size of the Memory address space of the I/O + bus that can be mapped to the system address space for a particular HB depends + on how much System Memory is allocated to the TCE table(s) and on how much + mappable I/O bus Memory Space is unavailable due to IOAs which are mapped + there. + Each TCE also contains two control bits. These are used to identify + whether that page is mapped to the system address space, and if the page is + mapped, whether it is mapped read/write, read only, or write only. See the + for a definition of these control + bits. + The TCE table is the analogue of the system translation tables. + However, unlike the system translation tables, the dynamic page faulting of + memory during an I/O operation is not required (the page fault value, 0b00, in + the TCE Page Mapping and Control field is used for error detection; that is, + access to an invalid TCE by the I/O creates an error indication to the + software). + The size and location of the HB’s TCE table is set up and + changed only by the firmware. + + + + R2--1. + + The platform must provide the + “64-bit-addressing” and + “ibm,extended-address” OF properties in all HB nodes + of the device tree and the “ibm,extended-address” + OF property in the root node of the OF device tree. + + + + + R2--2. + + The bits of the TCE must be implemented + as defined in . + + + + + + + TCE Definition + + + + + + + + Bits + + + + + Description + + + + + + + + 0 to 51 + + + RPN: If the page mapping and control field of the TCE + indicate anything other than page fault, then these bits contain the Real Page + Number (RPN) to which the bus address is mapped in the system address space. In + certain HB implementations, all of these bits may not be required, however + enough bits must be implemented to match the largest real address in the + platform. + + + + + 52 to 61 + + + Reserved for future use. + + + + + 62 to 63 + + + Page Mapping and Control: These bits define page mapping + and read-write authority. They are coded as follows: + 00 Page fault (no access) + 01 System address space (read only) + 10 System address space (write only) + 11 System address space (read/write) + Code point 0b00 signifies that the page is not mapped. + It must be used to indicate a page fault error. Hardware must not change its + state based on the value in the remaining bits of a TCE when code point 0b00 is + set in this field of the TCE. + For accesses to system address space with an invalid + operation (write to a read-only page or read to a write-only page), the HB + generates an error. See for more information + about error handling. + + + + +
+ + + + R2--3. + + If the address that the HB would use to + access the TCE table (in order to get the TCE) would access outside of the TCE + table, then the HB must create a TCE extent error (See ). + + + + + R2--4. + + Enough bits must be implemented in the + TCE so that DMA IOAs are able to access all System Memory addresses. + + + + + R2--5. + + Each PE must have its own independent + TCE table. + + + + + R2--6. + + Any non-recoverable error while an HB + is accessing its TCE table must result in a TCE access error; the action to be + taken by the HB being defined under the TCE access error in . + + + + + R2--7. + + In implementations which cache TCEs, if + software changes a TCE, then the platform must perform the following steps: + First, if any data associated with the page represented by that TCE is in an + I/O bridge cache or buffer, the hardware must write the data, if modified, to + System Memory. Secondly, it must invalidate the data in the cache. Finally, it + must invalidate the TCE in the cache. + + + + + R2--8. + + Neither an IOA nor an HB must ever + modify a TCE. + + + + + R2--9. + + If the page mapping and control bits in + the TCE are set to 0b00, the hardware must not change its state based on the + values of the remaining bits of the TCE. + + + + + R2--10. + + The OS must initialize all its TCEs + upon receiving control from the platform. + + + +
+
+ +
+ Example Address Maps + shows how to construct a + simple address map with one PHB and with Peripheral Memory, Peripheral I/O, and + SCA spaces below 4 GB. + shows how to construct + the address map with Peripheral Memory, Peripheral I/O, and SCA spaces above 4 + GB. This configuration allows some overlap of the System Memory space and + 32-bit I/O bus memory space (with the resulting loss of the TCE table in the + overlap), while moving some of the SCA spaces above 4 GB. Several things can be + noted from this configuration: + + + + I/O bus memory areas can overlap System Memory addresses (see + memory space of PHB0). However, significant overlap of these I/O bus memory + areas and the TCE table may significantly reduce the amount of TCE table space + that is available for mapping I/O memory space to system address space (a + potential performance impact). + + + + The System Memory which is above 4GB is shown starting at 4GB. + This architecture also allows this to be pushed further up, with Peripheral + Memory, Peripheral I/O, and SCAs existing above 4 GB and below the System + Memory areas. + + + + BPM’n,m to TPM’n,m spaces for different PHBs + (different “n”) are allowed to occur at the same memory addresses + in the various memory spaces of different I/O buses, but are not required to do + so (and are not shown as the same in the figure). Implementations are likely + have BPM’n,m to TPM’n,m at the same address range for all + “n” when the BPM’n,m to TPM’n,m ranges are below 4 + GB. + + + +
+ Example Address Map: One PHB, Peripheral Memory and Peripheral + I/O Spaces below 4 GB + + + + + + + + +
+ +
+ Example Address Map: Four PHBs, all Peripheral Memory and + Peripheral I/O Spaces above 4GB + + + + + + + + +
+
+
+ diff --git a/Platform/ch_interrupt_controller.xml b/Platform/ch_interrupt_controller.xml new file mode 100644 index 0000000..788c5f6 --- /dev/null +++ b/Platform/ch_interrupt_controller.xml @@ -0,0 +1,726 @@ + + + Interrupt Controller + + This chapter specifies the requirements for the LoPAR interrupt + controller. Platforms may chose to virtualize the interrupt controller or to + provide the PowerPC External Interrupt option. + +
+ Interrupt Controller Virtualization + Virtualization of the interrupt controller is done through the + Interrupt Support hcalls. See . +
+ +
+ PowerPC External Interrupt Option + The PowerPC External Interrupt option is based upon a subset of the + PowerPC External Interrupt Architecture. The PowerPC External Interrupt + Architecture contains a register-level architectural definition of an interrupt + control structure. This architecture defines means for assigning properties + such as priority, destination, etc., to I/O and interprocessor interrupts, as + well as an interface for presenting them to processors. It supports both + specific and distributed methods for interrupt delivery. See also + A PowerPC External + Interrupt.htm#38341.--> + In NUMA platform configurations, the interrupt controllers may be + configured in disjoint domains. The firmware makes the server numbers visible + to any single OS image appear to come from a single space without duplication. + This may be done by appropriately initializing the interrupt presentation + controllers or the firmware may translate the server numbers presented to it in + RTAS calls before entering them into the interrupt controller registers. The OS + is made aware that certain interrupts are only served by certain servers by the + inclusion of the “ibm,interrupt-domain” + property in the interrupt controller nodes. + +
+ PowerPC External Interrupt Option Requirements + The following are the requirements for the PowerPC External + Interrupt option. Additional requirements and information relative to the MSI + option, when implemented with this option, are listed in . + + + + R1--1. + + For the PowerPC External + Interrupt option: Platforms must implement interrupt architectures + that are in register-level architectural compliance with + A PowerPC External + Interrupt. + + + + + R1--2. + + For the PowerPC External + Interrupt option: The platform’s OF device tree must include + one or more PowerPC External Interrupt Presentation node(s), as children of the + root node. + + + + + R1--3. + + For the PowerPC External + Interrupt option: The platform’s OF device tree must include + an “ibm,ppc-interrupt-server#s” and an + “ibm,ppc-interrupt-gserver#s” property as defined for + each processor in the processor’s /cpus/cpu + node. + + + + + R1--4. + + For the PowerPC External + Interrupt option: The various + “ibm,ppc-interrupt-server#s” property values seen by a + single OS image must be all unique. + + + + + R1--5. + + For the PowerPC External + Interrupt option: If an OS image sees multiple global interrupt + server queues, the “ibm,ppc-interrupt-gserver#s” + properties associated with the various queues must have unique values. + + + + + R1--6. + + For the PowerPC External + Interrupt option: The platform’s OF device tree must include + a PowerPC External Interrupt Source Controller node, as defined for each Bus + Unit Controller (BUC) that can generate PowerPC External Interrupt Architecture + interrupts, as a child of the platform’s root node. + + + + + R1--7. + + For the PowerPC External + Interrupt option: The platform’s OF device tree must conform + to the and + include the appropriate mapping and interrupt properties to allow the mapping + of all non-zero XISR values (interrupt#) to the + corresponding node generating the interrupt. + + + + + R1--8. + + For the PowerPC External + Interrupt option: The PowerPC External Interrupt Presentation + Controller node must not contain the + “used-by-rtas” property. + + + + + R1--9. + + For the PowerPC External + Interrupt option: The PowerPC External Interrupt Source Controller + node must contain the “used-by-rtas” + property. + + + + + R1--10. + + For the PowerPC External + Interrupt option: If the interrupt hardware is configured such that, + viewed from any given OS image, any interrupt source controller cannot direct + interrupts to any interrupt presentation controller, then the platform must + include the “ibm,interrupt-domain” property + in all interrupt source and presentation controller nodes for that OS so that + the OS can determine the servers that may be valid targets for any given + interrupt. + + + + + R1--11. + + For the PowerPC External + Interrupt option: All interrupt controller registers must be + accessed via Caching-Inhibited, Memory Coherence not required and Guarded + Storage mapping. + + + + + R1--12. + + For the PowerPC External + Interrupt option: The platform must manage the Available Processor + Mask Register so that global interrupts (server number field of the eXternal + Interrupt Vector Entry (XIVE) set to a value from + “ibm,ppc-interrupt-gserver#s”) are only sent to one + of the active processors. + + + + + R1--13. + + For the PowerPC External + Interrupt option: The platform must initialize the interrupt + priority in each XIVE to the least favored level (0xFF), enable any associated + IER bit for interrupt sources owned by the OS, and set the Current Processor + Priority Register to the Most favored level (0x00) prior to the transfer of + control to the OS so that no interrupts are signaled to a processor until the + OS has taken explicit action. + + + + + R1--14. + + For the PowerPC External + Interrupt option: Any implemented PowerPC External Interrupt + Architecture registers that are not reported in specific interrupt source or + destination controller nodes (such as the APM register) must be included in the + “reg” property of the + /reserved node. + + + + + R1--15. + + For the PowerPC External + Interrupt option: The interrupt source controller must prevent signalling new + interrupts when the XIVE interrupt priority field is set to the least favored + level. + + + + + R1--16. + + For the PowerPC External + Interrupt option: Interrupt controllers that do not implement the + behavior of Requirement , must provide + an Interrupt Enable Register (IER) which can be manipulated by RTAS, + + + + + R1--17. + + For the PowerPC External + Interrupt option: The platform must assign the Bus Unit Identifiers + (BUIDs) such that they form a compact address space. That is, while the first + BUID value is arbitrary, subsequent BUIDs should be contiguous. + + + + + R1--18. + + For the PowerPC External + Interrupt option: Platforms implementing interrupt server number + fields greater than 8 bits must include the + “ibm,interrupt-server#-size” property in the interrupt + source controller node. + + + + + R1--19. + + For the PowerPC External + Interrupt option: Platforms implementing interrupt buid number + fields greater than 9 bits must include the + “ibm,interrupt-buid-size” property in the interrupt + presentation controller node. + + + + + R1--20. + + For the PowerPC External + Interrupt option: Platforms must include the + “ibm,interrupt-server-ranges” property in the + interrupt presentation controller node. + + + + +
+ +
+ PowerPC External Interrupt Option Properties + See for property definitions. +
+ +
+ MSI Option + The Message Signaled Interrupt (MSI) or Enhanced MSI (MSI-X) + capability of PCI IOAs in many cases allows for greater flexibility in + assignment of external interrupts to IOA functions than the predecessor Level + Sensitive Interrupt (LSI) capability, and in some cases treats MSIs as a + resource pool that can be reassigned based on availability of MSIs and the need + of an IOA function for more interrupts than initially assigned. Platforms that + implement the MSI option implement the ibm,change-msi and + ibm,query-interrupt-source-number RTAS calls. These RTAS + calls manage interrupts in a platform that implements the MSI option. In + particular, these calls assign additional MSI resources to an IOA function (as + defined by its PCI configuration address: PHB_Unit_ID_Hi, + PHB_Unit_ID_Low, and config_addr), when supported by the platform. + See for more information on theses RTAS calls for + MSI management. + This architecture will refer generically to the MSI and MSI-X + capabilities as simply “MSI,” except where differentiation is + required. In this architecture, MSIs and LSIs are what the IOA function + signals, and what the software sees for that signal is ultimately the LSI or + MSI source number. The interrupt source numbers returned + by the ibm,query-interrupt-source-number RTAS call are + the numbers used to control the interrupt as in the ibm,get-xive, + ibm,set-xive, ibm,int-on, + and ibm,int-off RTAS calls. + PCI-X and PCI Express IOA functions that signal interrupts are + required by the PCI specifications to implement either the MSI or MSI-X + interrupt capabilities, or both. For PCI Express, it is expected that IOAs will + only support MSI or MSI-X (that is, no support for LSIs). When both MSI and + MSI-X are implemented by an IOA function, the MSI method will be configured by + the platform, but may be overridden by the OS or device driver, via the + ibm,change-msi RTAS call, to be MSI-X or, if assigned by + the firmware, to LSI (by removal of the MSIs assigned). + summarizes the LSI and MSI support. + + + LSI and MSI Support Requirements and Initial Assignment + + + + + + + + + + + + + IOA Type + + + + + LSI required by PCI specifications? + + + + + MSI or MSI-Xrequired by PCI specifications? + + + + + Bridge between IOA and PHB + + + + + Possible platform support + + + + + Initial interrupt assignmentAssignment means to allocate the platform + resources and to enable the interrupt in the IOA function’s + configuration space. + + + + + + If PHB does not support MSI option + (Not including PCI Express HBs) + + + If PHB supports MSI option + (Including all PCI Express HBs) + + + + + + + PCI + + + When interrupts are required + + + No + (allowed; optional) + + + - + + + LSI + + + LSI or MSI + + + LSIIf MSIs are to + be supported, the device driver must enable via the + ibm,change-msi RTAS call. + + + + + PCI-X + + + Encouraged when interrupts are required, for backward + platform compatibility + + + Yes + + + - + + + LSI + + + LSI or MSI + + + LSIIf MSIs are to + be supported, the device driver must enable via the + ibm,change-msi RTAS call. + + + + + PCI Express + + + Discouraged + (expect IOAs to not implement in most cases) + + + Yes + + + None or PCI Express switch only + + + n/a + + + MSI + + + MSIMSI as an + initial assignment means that one or more MSIs are reported as being available + for the IOA function. In addition, LSIs may also be reported but not enabled, + in which case if the device driver removes the assigned MSIs, the assigned LSI + are enabled by the platform firmware in the IOA function’s configuration + space. + + + + + Reverse bridge + (primary, PCI Express secondary) + + + LSI or not supported + If PCI Express IOA function does not support LSI, + then this combination is not supported. + + + LSI + If PCI Express + IOA function does not support LSI, then this combination is not + supported. or MSI + + + LSI + If the PCI + Express IOA function does not support LSI, then the platform will set the + initial interrupt assignment to MSI, and if the device driver does not support + MSI, then the IOA function will not be configurable (that is, conversion from + MSI to LSI through the bridge is not supported by this architecture). If LSI is + the initial assignment, then if MSIs are to be supported, device driver must + enable via the ibm,change-msi RTAS + call. + + + + +
+ + The ibm,change-msi RTAS call is used to query + the initial number of MSIs assigned to a PCI configuration address and to + request a change in the number of MSIs assigned. The MSIs interrupt source + numbers assigned to an IOA function are returned via the + ibm,query-interrupt-source-number + RTAS call. In addition, when the + ibm,query-interrupt-source-number RTAS call is + implemented, it may be used to query the LSI source numbers, also. The + ibm,query-interrupt-source-number RTAS call is called + iteratively, once for each interrupt assigned to the IOA function. When an IOA + function receives an initial assignment of an LSI, the interrupt number for + that LSI may also be obtained through the same OF device tree properties that + are used to report interrupt information when the + ibm,query-interrupt-source-number RTAS call is not + implemented. + + + + R1--1. + + The platform must implement the MSI + option if the platform contains at least one PCI Express HB. + Architecture and Software Note: The MSI + option may also be implemented in the absence of any PCI Express HBs. In that + case, the implementation of the MSI option is via the presence of the + implementation of the associated ibm,change-msi and + ibm,query-interrupt-source-number RTAS calls. + + + + + R1--2. + + For the MSI option: + The platform must implement the PowerPC External Interrupt option. + + + + + R1--3. + + For the MSI option: + The platform must implement the ibm,change-msi + and ibm,query-interrupt-source-number RTAS calls. + + + + + R1--4. + + For the MSI option: + The platform must initially assign LSI or MSIs to IOA functions as + defined in and must enable the + assigned interrupts in the IOA function’s configuration space (the + interrupts remains disabled at the PHB, and must be enabled by the device + driver though the ibm,set-xive and + ibm,int-on RTAS calls. + + + + + R1--5. + + For the MSI option: + The platform + must provide a minimum of one MSI per IOA function (that is per each unique PCI + configuration address, including the Function #) to be supported beneath the + interrupt source controller, and any given MSI and MSI source number must not + be shared between functions or within one function (even within the same + PE). + + + + + R1--6. + + For the MSI option: + The platform + must provide at least one MSI port (the address written by the MSI) per + Partitionable Endpoint (PE). + Platform Implementation Note: Requirement + in conjunction with Requirement may have certain ramifications on the + design. Depending on the implementation, a unique MSI port per IOA function may + be required, and not just a unique port per PE. + + + + + R1--7. + + For the MSI option with the + LPAR option: The platform must prevent a PE from creating an + interrupt to a partition other than those to which the PE is authorized by the + platform to interrupt. + + + + + R1--8. + + For the MSI option: + The platform must set the PCI configuration space MSI registers properly in an + IOA at all the following times: + + + + Initial boot time + + + + During the ibm,configure-connector RTAS + call + + + + During the ibm,change-msi or + ibm,query-interrupt-source-number RTAS call + + + + + + + R1--9. + + For the MSI option: + The platform must initialize any bridges necessary to appropriately route + interrupts at all the following times: + + + + At initial boot time + + + + During the ibm,configure-connector RTAS + call + + + + During the ibm,configure-bridge RTAS + call + + + + During the ibm,change-msi or + ibm,query-interrupt-source-number RTAS call + + + + + + + R1--10. + + For the MSI option: + The platform must provide the “ibm,req#msi” + property for any IOA function which is + requesting MSIs; at initial boot time and during the + ibm,configure-connector RTAS call. + + + + + R1--11. + + For the MSI option: + The platform + must remember and recover on error recovery any previously allocated and setup + interrupt information in the platform-owned hardware. + Software and Platform Implementation Note: In + Requirement , it is possible that some + interrupts may be lost as part of the error recovery, and software should be + implemented to take into consideration that possibility. + + + + +
+
+ +
+ Platform Reserved Interrupt Priority Level Option + The Platform Reserved Interrupt Priority Level option allows + platforms to reserve interrupt priority levels for internal uses. When the + platform exercises this option, it notifies the client program via the OF + device tree “ibm,plat-res-int-priorities” + property of the root node of the device tree. + + + + R1--1. + + For the Platform Reserved + Interrupt Priority Level option: The platform must include + the“ibm,plat-res-int-priorities” + property in the root node of the device tree. + + + + + R1--2. + + For the Platform Reserved + Interrupt Priority Level option: The platform must not reserve + priority levels 0x00 through 0x07 and 0xFF for internal use. + + + + +
+ diff --git a/Platform/ch_io_devices.xml b/Platform/ch_io_devices.xml new file mode 100644 index 0000000..e6df909 --- /dev/null +++ b/Platform/ch_io_devices.xml @@ -0,0 +1,989 @@ + + + I/O Devices + + This chapter describes requirements for IOAs. It adds detail to areas + of the PCI architectures (conventional PCI, PCI-X and PCI Express) that are + either unaddressed or optional. It also places some requirements on firmware + and the OS for IOA support. It provides references to specifications to which + IOAs must comply and gives design notes for IOAs that run on LoPAR systems. + + +
+ PCI IOAs + + + + + R1--1. + + All PCI IOAs must be capable of decoding and + generating either a full 32-bit address or a full 64-bit address. + + + + + R1--2. + + IOAs that implement conventional PCI must be compliant with the + most recent version of the at the + time of their design, including any approved Engineering Change Requests (ECRs) + against that document. + + + + + R1--3. + + IOAs that implement PCI-X must be compliant + with the most recent version of the + at the time of their design, including any approved Engineering Change Requests + (ECRs) against that document. + + + + + R1--4. + + IOAs that implement PCI Express must be + compliant with the most recent version of the at the time of their design, including any + approved Engineering Change Requests (ECRs) against that document + + + + + Architecture Note: Revision 2.1 and later of + the PCI Local Bus Specification requires that PCI masters + which receive a Retry target termination to unconditionally repeat the same + request until it completes. The master may perform other bus transactions, but + cannot require those to complete before repeating the original transaction + which was previously target terminated with Retry. Revision 2.1 of the + specification (page 49) also includes an example which describes how the + requirement above applies to a multi-function IOA. See page 48-49 of the 2.1 + revision of the PCI Local Bus Specification for more + detail. Revision 2.0 of the PCI Local Bus Specification + includes a definition of target termination via Retry, but did not spell out + the requirement described above for masters, as does the 2.1 revision of the + specification. Masters which are designed based on revision 2.0 of the + specification that perform other transactions following target termination with + Retry, may cause live-locks and/or deadlocks when installed in a system that + utilizes bridges (host bridge or PCI-PCI bridges) that implement Retry, delayed + transactions, and/or TCEs, when those masters require following transactions to + complete before the original transaction that was terminated with the target + Retry. This revision 2.0 to revision 2.1 compatibility problem has been + observed on several IOAs that have asked for deviations to Requirement . Wording was added to the revision 2.2 of + the PCI Local Bus Specification which makes a statement + similar to this Architecture Note. + +
+ Resource Locking + + + + R1--1. + + PCI IOAs, excepting bridges, must not depend on the PCI LOCK# + signal for correct operation nor require any other PCI IOA to assert LOCK# for + correct operation. + + + + + There are some legacy IOAs on legacy buses which require LOCK#. + Additionally, LOCK# is used in some implementations to resolve deadlocks + between bridges under a single PHB. These uses of LOCK# are permitted. +
+ +
+ PCI Expansion ROMs + + + + R1--1. + + PCI expansion ROMs must have a ROM image + with a code type of 1 for OF as provided in the . This ROM image must abide by the ROM image + format for OF as documented in the . + + + + + LoPAR systems rely on OF - not BIOS - to boot. This is why strong + requirements for OF device support are made. + Vital Product Data (VPD) is an optional feature for PCI adapters + and it is strongly recommended that VPD be included in all PCI expansion ROMs. + If it is put in the PCI expansion ROM in accordance with the , VPD will be reported in the OF device + tree. If the VPD information is formatted as defined in Revision 2.2 with the + new capabilities feature, or in any other format, firmware will not read the + VPD, and the device driver for the IOA will have to reformat any provided VPD + into an OS specified format. It is still required that the keywords and their + values must conform to those specified by either PCI 2.1 or PCI 2.2, no matter + how they are formatted. Refer to Requirement . +
+ +
+ Assignment of Interrupts to PCI IOAs + + + + R1--1. + + All PCI IOAs must use the PowerPC + interrupt controller, except when made transparent to the OS by the platform + through the architected hcall()s. + + + + + R1--2. + + PCI IOAs that do not reside in the + Peripheral Memory Space and Peripheral I/O Space of the same PHB must not share + the same LSI source. + + + + For further information on the interrupt controller refer to . + It is strongly advised that system board designers assign one + interrupt for each interrupt source. Additionally, multi-function PCI IOAs + should have multiple interrupt sources. For restrictions on sharing interrupts + with the LPAR option, see Requirement . + For restrictions on sharing MSIs, see Requirement and Requirement . +
+ +
+ PCI-PCI Bridge Devices + + + + R1--1. + + Firmware must initialize all PCI-to-PCI + bridges. See . + + + + All bridges and switches are required to comply with the bus + specification(s) of the buses to which they are attached. See Requirement . +
+ +
+ Graphics Controller and Monitor Requirements for Clients + + The graphics requirements for servers are different from those for + portable and personal systems. + + + + R1--1. + + Plug-in graphics controllers for portable + and personal platforms must provide graphics mode sets in the OF PCI expansion + ROM image in accordance with the + . + + + + + Portable and personal platforms are strongly urged to support some + mechanism which allows the platform to electronically sense the display + capabilities of monitors. + + For graphics controllers that are placed on the system board, the + graphics mode sets can be put in system ROM. The mode set software put in the + system ROM in this case would be FCode and would be largely or entirely the + same as the FCode that would be in the PCI expansion ROM if the same graphics + controller was put on a plug-in PCI card. +
+ +
+ PCI Plug-in Graphic Cards + + + + R1--1. + + (Requirement Number Reserved + For Compatibility) + + + + + R1--2. + + PCI plug-in graphics cards which are + going to be the primary display IOA during the time prior to the OS device + driver being loaded must contain an OF display driver on the IOA. + + + +
+ +
+ PCI Cache Support Protocol + The PCI architecture allows for the optional implementation of + caching of data. This architecture basically assumes that the data in I/O + memory is non-coherent. As such, platforms are not required to implement the + optional PCI Cache Support protocol using the SBO# and SDONE signals. + Therefore, IOAs used in LoPAR platforms should not count on those signals for + proper operations. + + + + R1--1. + + IOAs used in LoPAR platforms + and their device drivers must not require the use of the PCI signals SBO# and + SDONE for proper operations. + + + +
+ +
+ PCI Configuration Space for IOAs + There are several writable fields in the PCI Configuration Header. + Some of these are written by the firmware and should never be changed by the + device driver. + + + + R1--1. + + All registers and bits in the PCI Configuration Header must be + set to a platform specific value by firmware and preserved by software, except + that software is responsible for setting the configuration space as indicated + in . + + + Software Programming of PCI Configuration Header Registers + + + + + + + + Register Name + + + Bit Name + + + Software Action + + + + + + + Command + + + Bus Master + + + Must write to a 1 before the first DMA operation after a + reset. Must write to a 0 before unconfiguring device driver. + + + + + Memory Space + + + Must write to a 1 before the first MMIO operation to + IOA’s memory space (if any) after a reset. Must write to a 0 before + unconfiguring device driver. + + + + + IO Space + + + Must write to a 1 before the first MMIO operation to + IOA’s I/O space (if any) after a reset. Must write to a 0 before + unconfiguring device driver. + + + + + all other bits + + + Must restore to previous value after any reset operation + (for example, via ibm,set-slot-reset Function 1 or 3). + The ibm,configure-bridge RTAS call is available to assist + in restoring values, where appropriate. + + + + + Built in Self Test (BIST) + + + all + + + If implemented, software may use if desired. + + + + + all other PCI header registers that may be modified by + firmware after initial reset or by ibm,configure-connector for DR operations + + + all + + + Must restore to previous value after any reset operation + (for example, via ibm,set-slot-reset-state Function 1). + The ibm,configure-bridge RTAS call is available to assist + in configuring PCI bridges and switches, where appropriate. + + + + +
+ + + + + R1--2. + + All IOAs that implement PCI-X Mode 2 or PCI Express must supply + the “ibm,pci-config-space-type” property + (see ). + Implementation Note: The + “ibm,pci-config-space-type” + property in Requirement is added for platforms that support + I/O fabric and IOAs that implement PCI-X Mode 2, and PCI Express. To access the + extended configuration space provided by PCI-X Mode 2 and PCI Express, all I/O + fabric leading up to an IOA must support a 12-bit register number. In other + words, if a platform implementation has a conventional PCI bridge leading up to + an IOA that implements PCI-X Mode 2, the platform will not be able to provide + access to the extended configuration space of that IOA. The + “ibm,config-space-type” property in the IOA's OF node + is used by device drivers to determine if an IOA’s extended + configuration space can be accessed. + + + +
+ +
+ PCI IOA Use of PCI Bus Memory Space Address 0 + Some PCI IOAs will fail when given a bus address of 0. In the PC + world, address 0 would not be a good address, so some PCI IOA designs which + were designed for the PC arena will check for an address of 0, and fail the + operation if it is 0. + + + + R1--1. + + For systems that use PCI IOAs + which will fail when given a bus address of 0 for DMA operations, and when the + operations for which those IOAs are used are other than system memory dump + operations, then the OS must prevent the mapping of PCI bus address 0 for PCI + DMA operation for such IOAs. + + + + + R1--2. + + PCI IOAs used for dumping contents of + system memory must operate properly with a PCI bus address of 0 for PCI DMA + operations. + + + + + R1--3. + + The firmware must not map an IOA used for + loading a boot image to an address of 0, when loading a boot image, if that IOA + cannot accept an address of 0. + + + + Implementation Note: A reasonable + implementation of Requirement would + be to have an interface between the device driver and the kernel to allow the + device driver to indicate to the kernel that the restriction is required for + that IOA, so that all IOAs for that kernel image are not affected. +
+ +
+ PCI Express Completion Timeout + Prior to the implementation of the PCI Express additional + capability to set the Completion Timeout Value and Completion Timeout Disable + in the PCI Express Device Control 2 register of an IOA, the IOAs need + device-specific way to provide the disable capability. In addition, the + platforms need to provide a way for the OSs and device drivers to know when to + disable the completion timeout of these devices that only provide a + device-specific way of doing so. + + + + R1--1. + + PCI Express IOAs must either provide a + device-specific way to disable their DMA Completion Timeout timer or must + provide the Completion Timeout Disable or Completion Timeout Value capability + in the PCI Express Device Control 2 register, and device drivers for IOAs that + provide a device-specific way must disable their DMA Completion Timeout timer + if it is either unknown whether the IOA provides a sufficiently long timer + value for the platform, or if it is known that they do not provide a sufficient + timeout value (for example, if the + “ibm,max-completion-latency” property is not + provided). + + + + + R1--2. + + Platforms must provide the + “ibm,max-completion-latency” property in + each PCI Express PHB node of the OF Device Tree. + + + + +
+ +
+ PCI Express I/O Virtualized (IOV) Adapters + PCI Express defines I/O Virtualized (IOV) adapters, where such an + adapter has separate resources for each virtual instance, called a Virtual + Function (VF). There are two PCI specifications that exist to define such + adapters: + + + + defines the + requirements for SR-IOV adapters. + + + + defines the + requirements for MR-IOV adapters. + + + + The interface presented to an OS from an MR-IOV adapter will look + the same as an SR-IOV adapters, and therefore will not be described separately + here. + IOV adapters and/or the VFs of an IOV adapter that has IOV enabled, + are assigned to OSs as follows (see also for a full set of characteristics of these + environments): + + + + For the Legacy Dedicated environment, the + entire adapter is assigned to one LPAR, with the IOV functionality not enabled. + In this mode, the OS provides device driver(s) for the adapter Function(s). VFs + do not exist, because IOV is not enabled. The OS is given the capability to do + Hot Plug add, remove, and replace in a non-managed environment (without an + HMC), and may be given that capability in a managed environment. + + + + For the SR-IOV Non-shared environment, the + entire adapter is assigned to one LPAR, with IOV functionality enabled, but + with the Physical Function(s) (PFs) of the adapter hosted by the platform. Only + VFs are presented to the OS. The OS is given the capability to do Hot Plug add, + remove, and replace in a non-managed environment (without an HMC), and may be + given that capability in a managed environment. + + + + For the SR-IOV Shared environment, the + adapter is assigned to the platform, with IOV functionality enabled. The + platform then assigns VF(s) to OS(s). Only the managed environment applies, and + add/remove/replace operations are controlled by DLPAR operations to the OS(s) + from the management console. + + + + For all environments except the SR-IOV Shared, multiple functions + will appear as a multi-function IOA with possible sharing of a single PE. For + example, the multi-function adapters may have a shared EEH domain and shared + DMA window. + Determination of which of the above environments is supported for a + given platform and partition or OS type is beyond the scope of this + architecture. + defines the + characteristics of these environments. + + + IOV Environment Characteristics + + + + + + + + + +   + + + + + Legacy Dedicated + + + + + SR-IOV Non-shared + + + + + SR-IOV Shared + + + + + + + + Entire adapter assigned to OS, IOV not enabled + + + yes + + + n/a + + + n/a + + + + + Entire adapter assigned to OS, IOV enabled + + + n/a + + + yes + + + n/a + + + + + Adapter can be shared across multiple OSs, IOV enabled + + + n/a + + + n/a + + + yes + + + + + Function DD support + + + Plain Function only + (not VF or PF) + + + VF only + + + VF only + + + + + PFs managed by platform? + + + n/a + + + yes + + + yes + + + + + Managed environment support? + + + yes + + + yes + + + yes + + + + + Non-managed environment support? + + + yes + + + yes + + + no + + + + + OS controlled Hot Plug capable? + + + yes + + + yes + + + no + + + + + DLPAR capable? + + + yes + + + yes + + + yes + + + + + All functions under one PHB in the OF Device Tree for the adapter? + + + yes + + + yes + + + no + + + + + All functions under separate PHBs in the OF Device Tree + for the same adapterThe adapter is + physically under one PHB, but the platform creates separate + “virtual” PHBs in the OF Device Tree and virtualizes the PCI + Express configuration space for the various functions.? + + + no + + + no + + + yes + + + + + config_addr translation + (virtualization) by the platform (that is, the bus/device/function of the + config_addr does not necessarily correspond to what the + device has programmed) + + + no + + + yes + + + yes + + + + + Shared PE domain (for example, shared EEH domain, shared DMA window) + + + yes + + + yes + + + no + + + + +
+ + + + R1--1. + + PCI Express Single Root IOV (SR-IOV) + adapters must comply to the . + + + + + R1--2. + + PCI Express Multi-Root IOV (MR-IOV) + adapters must comply to the . + + + + + R1--3. + + The platform must present within the + device tree nodes for all PCI Express adapters configured to operate in IOV + mode the "ibm,is-vf" property as defined in section + . + + + +
+
+ +
+ Multi-Initiator SCSI Support + Multi-initiator SCSI support is identified in the OF device tree. + + + + R1--1. + + Platform Implementation: + Platforms must support the “scsi-initiator-id” + property as described in and . + + + +
+ +
+ Contiguous Memory + I/O devices that require contiguous memory pages (either real or via + contiguous TCEs) cannot reasonably be accommodated in LoPAR platforms. When + TCEs are turned off, that would require that real physical memory addresses be + allocated. When TCEs are on, that would require contiguous TCEs be assigned, + and although that is the first attempt by the OS’s TCE assignment + algorithm, the algorithm will assign non-contiguous ones if contiguous ones + cannot be assigned. Dynamic Reconfiguration complicates the contiguous problem + even further. + + + + R1--1. + + I/O devices and/or their device drivers used + in LoPAR platforms must implement scatter/gather capability for DMA operations + such that they do not require contiguous memory pages to be allocated for + proper operation. + + + +
+ +
+ Re-directed Serial Ports + The “ibm,vty-wrap-capable” OF + device tree property will be present in an OF device tree of a serial port node + when the OS data communication with that serial port controller can be + redirected, or wrapped, away from the physical serial port connector to an + ibm,vty device, which is often a virtual terminal session + of the Hardware Management Console (HMC). This property indicates to serial + port diagnostic programs that additional end user information should be + displayed during the serial port diagnostic test indicating that it is possible + that serial port data could be redirected away from the physical serial port + preventing the execution of wrap tests with physical wrap plugs. The end user + information should describe that initiating a virtual terminal session causes + the serial port controller's data to be wrapped away from the physical serial + port connection and that terminating a virtual terminal session causes the + serial port controller's data to be returned to the physical serial port + connection. The “ibm,vty-wrap-capable” + property is present with a value of null when this re-direction capability + exists and is absent when this capability does not exist. + + + + R1--1. + + The “ibm,vty-wrap-capable” + OF device tree property must + be present in an OF device tree of a serial port node when the OS data + communication with that serial port controller can be redirected, or wrapped, + away from the physical serial port connector to an ibm,vty device, and must not + be present if this capability does not exist. + + + +
+ +
+ System Bus IOAs + This section lists the requirements for the systems to support IOAs + connected to the system bus or main I/O expansion bus. + + + + R1--1. + + Each system bus IOA must be a bus + master. + + + + + R1--2. + + Firmware must assign unique addresses to all + system bus IOA facilities. + + + + + R1--3. + + Addresses assigned to system bus IOA + facilities must not conflict with the addresses mapped by any host bridge on + the system bus. + + + + + R1--4. + + System bus IOAs must be assigned interrupt + sources for their interrupt requirements by firmware. + + + + + R1--5. + + A system bus IOA’s OF + “interrupts” property must reflect + the interrupt source and type allocation for the device. + + + + + R1--6. + + All system bus IOA interrupts must be low + true level sensitive (referred to as level sensitive). + + + + + R1--7. + + Interrupts assigned to system bus IOAs must + not be shared with other IOAs. + + + + + R1--8. + + The OF unit address (first entry of the + “reg” property) of a system + bus IOA must stay the same from boot to boot. + + + + + R1--9. + + Each system bus IOA must have documentation + for programming the IOA and an OF binding which describes at least the + “name”, + “reg”, + “interrupts”, and + “interrupt-parent” + properties for the device. + + + + +
+ diff --git a/Platform/ch_io_topology.xml b/Platform/ch_io_topology.xml new file mode 100644 index 0000000..87fc315 --- /dev/null +++ b/Platform/ch_io_topology.xml @@ -0,0 +1,2610 @@ + + + I/O Bridges and Topologies + + There will be at least one bridge in a platform which interfaces to the + system interconnect on the processor side, and interfaces to the Peripheral + Component Interface (PCI) bus on the other. This bridge is called the + PCI Host Bridge (PHB). + The architectural requirements on the PHB, as well as other aspects of the I/O + structures, PCI bridges, and PCI Express switches are defined in this chapter. + + +
+ I/O Topologies and Endpoint Partitioning + As systems get more sophisticated, partitioning of various components + of the system will be used, in order to obtain greater Reliability, + Availability, and Serviceability (RAS). For example, Dynamic Reconfiguration + (DR) allows the removal, addition, and replacement of components from an + OS’s pool of resources, without having to stop the operation of that OS. + In addition, Logical Partitioning (LPAR) allows the isolation of resources used + by one OS from those used by another. This section will discuss aspects of the + partitioning of the I/O subsystem. Further information on DR and LPAR can be + found in . + To be useful, the granularity of assignment of I/O resources to an OS + needs to be fairly fine-grained. For example, it is not generally acceptable to + require assignment of all I/O under the same PCI Host Bridge (PHB) to the same + partition in an LPARed system, as that restricts configurability of the system, + including the capability to dynamically move resources between + partitionsDynamic LPAR or DLPAR is + defined by the Logical Resource Dynamic Reconfiguration (LRDR) option. See + for more information. Assignment of all + IOAs under the same PHB to one partition may be acceptable if that I/O is + shared via the Virtual I/O (VIO) capability defined in .. To be able to partition + I/O adapters (IOAs), groups of IOAs or portions of IOAs for DR or to different + OSs for LPAR will generally require some extra functionality in the platform + (for example, I/O bridges and firmware) in order to be able to partition the + resources of these groups, or endpoints, while at the same time preventing any + of these endpoints from affecting another endpoint or getting access to another + endpoint’s resources. These endpoints (that is, I/O subtrees) that can + be treated as a unit for the purposes of partitioning and error recovery will + be called Partitionable Endpoints (PEs)A + “Partitionable Endpoint” in this architecture is not to be + confused with what the PCI Express defines as an “endpoint.” PCI + Express defines an endpoint as “a device with a Type 0x00 Configuration + Space header.” That means PCI Express defines any entity with a unique + Bus/Dev/Func # as an endpoint. In most implementations, a PE will not exactly + correspond to this unit. and this concept will be called + Endpoint Partitioning. + A PE is defined by its Enhanced I/O Error Handling (EEH) domain and + associated resources. The resources that need to be partitioned and not overlap + with other PE domains include: + + + + The Memory Mapped I/O (MMIO) Load and + Store address space which is available to the PE. This is + accomplished by using the processor’s Page Table mechanism (through + control of the contents of the Page Table Entries) and not having any part of + two separate PEs’ MMIO address space overlap into the same 4 KB system + page. Additionally, for LPAR environments, the Page Table Entries are + controlled by the hypervisor. + + + + The DMA I/O bus address space which is available to the PE. This is + accomplished by a hardware mechanism (in a bridge in the platform) which + enforces the correct DMA addresses, and for LPAR, this hardware enforcement is + set up by the hypervisor. It is also important that a mechanism be provided for + LPAR such that the I/O bus addresses can further be limited at the system level + to not intersect; so that one PE cannot get access to a partition’s + memory to which it should not have access. The Translation Control Entry (TCE) + mechanism, when controlled by the firmware (for example, a hypervisor), is such + a mechanism. See for more information + on the TCE mechanism. + + + + The configuration address space of the PE, as it is made available + to the device driver. This is accomplished through controlling access to a + PE’s configuration spaces through Run Time Abstraction Services (RTAS) + calls, and for LPAR, these accesses are controlled by the hypervisor. + + + + The interrupts which are accessible to the PE. An interrupt cannot + be shared between two PEs. For LPAR environments, the interrupt presentation + and management is via the hypervisor. + + + + The error domains of the PE; that is, the error containment must be + such that a PE error cannot affect another PE or, for LPAR, another partition + or OS image to which the PE is not given access. This is accomplished though + the use of the Enhanced I/O Error Handling (EEH) option of this architecture. + For LPAR environments, the control of EEH is through the hypervisor via several + RTAS calls. + + + + The reset domain: A reset domain contains all the components of a + PE. The reset is provided programmatically and is intended to be implemented + via an architected (non implementation dependent) method.For example, through a Standard Hot Plug + Controller in a bridge, or through the Secondary Bus Reset bit in the Bridge + Control register of a PCI bridge or switch. Resetting a + component is sometimes necessary in order to be able to recover from some types + of errors. A PE will equate to a reset domain, such that the entire PE can be + reset by the ibm,set-slot-reset RTAS call. For LPAR, the + control of the reset from the RTAS call is through the hypervisor. + + + + In addition to the above PE requirements, there may be other + requirements on the power domains. Specifically, if a PE is going to + participate in DR, including DLPAR,To + prevent data from being transferred from one partition to another via data + remaining in an IOA’s memory, most implementations of DLPAR will require + the power cycling of the PE after removal from one partition and prior to + assigning it to another partition. then either the power + domain of the PE is required to be in a power domain which is separate from + other PEs (that is, power domain, reset domain, and PE domain all the same), or + else the control of that power domain and PCI Hot Plug (when implemented) of + the contained PEs will be via the platform or a trusted platform agent. When + the control of power for PCI Hot Plug is via the OS, then for LPAR + environments, the control is also supervised via the hypervisor. + It is possible to allow several cooperating device drivers to share a + PE. Sharing of a PE between device drivers within one OS image is supported by + the constructs in this architecture. Sharing between device drivers in + different partitions is beyond the scope of the current architecture. + A PE domain is defined by its top-most (closest to the PHB) PCI + configuration address (in the terms of the RTAS calls, the + PHB_Unit_ID_Hi, PHB_Unit_ID_Low, and config_addr ), which will be + called the PE configuration address in this architecture, + and encompasses everything below that in the I/O tree. The top-most PCI bus of + the PE will be called the PE primary bus. Determination + of the PE configuration address is made as described in . + A summary of PE support can be found in . This architecture assumes that there is a + single level of bridge within a PE if the PE is heterogeneous (some + Conventional PCI Express), and these cases are shown by the shaded cells in the + table. + + + Conventional PCI Express PE Support Summary + + + + + + + + + Function + + + + + IOA Type + + + + + PE Primary BusPCI Express  + + + + + + + + PE determination + (is EEH supported for the IOA?) + + + All + + + Use the ibm,read-slot-reset-state2 + RTAS call. + + + + + PE reset + + + All + + + PE reset is required for all PEs and is + activated/deactivated via the ibm,set-slot-reset RTAS + call. The PCI configuration address used in this call is the PE configuration + address (the reset domain is the same as the PE domain). + + + + + + ibm,get-config-addr-info2RTAS call + + + PCI + Express + + + Required to be implemented. + + + + + Top of PE domain determinationPE + configuration address is used as input to the + RTAS calls which are used for PE control, namely: + ibm,set-slot-reset, + ibm,set-eeh-option, + ibm,slot-error-detail, + ibm,configure-bridge + (How to obtain the PE configuration address) + + + PCI + Express + + + Use the ibm,get-config-addr-info2 + RTAS call to obtain PE configuration address. + + + + + Shared PE determinationIf device + driver is written for the shared PE + environment, then this may be a don’t care. + (is there more than one IOA per PE?) + + + PCI + Express + + + Use the ibm,get-config-addr-info2 + RTAS call. + + + + + PEs per PCI Hot Plug domain and PCI Hot Plug control + point + + + PCI + Express + + + May have more than one PE per PCI Hot Plug DR entity, but + a PE will be entirely encompassed by the PCI Hot Plug power domain. If more + than one PE per DR entity, then PCI Hot Plug control is via the platform or + some trusted platform agent. + + + + +
+ + + + R1--1. + + All platforms must implement the + ibm,get-config-addr-info2 RTAS call. + + + + + R1--2. + + All platforms must implement the + ibm,read-slot-reset-state2 RTAS call. + + + + + R1--3. + + For the EEH option: + The resources of one PE must not overlap the resources of another PE, + including: + + + + Error domains + + + + MMIO address ranges + + + + I/O bus DMA address ranges (when PEs are below the same PHB) + + + + Configuration space + + + + Interrupts + + + + + + + R1--4. + + For the EEH option: + All the following must be true relative to a PE: + + + + An IOA function must be totally encompassed by a PE. + + + + All PEs must be independently resetable by a reset domain. + + + Architecture Note: The partitioning of PEs + down to a single IOA function within a multi-function IOA requires a way to + reset an individual IOA function within a multi-function IOA. For PCI, the only + mechanism defined to do this is the optional PCI Express Function Level Reset + (FLR). A platform supports FLR if it supports PCI Express and the partitioning + of PEs down to a single IOA function within a multi-function IOA. When FLR is + supported, if the ibm,set-slot-reset RTAS call uses FLR + for the Function 1/Function 0 + (activate/deactivate reset) sequence for an IOA function, then the platform + provides the “ibm,pe-reset-is-flr” property + in the function’s node of the OF device tree, See + for more information. + + + + + R1--5. + + The platform must own (be + responsible for) any error recovery for errors that occur outside of all PEs + (for example in switches and bridges above defined PEs). + Implementation Note: As part of the error + recovery of Requirement , the platform + may, as part of the error handling of those errors, establish an equivalent EEH + error state in the EEH domains of all PEs below the error point, in order to + recover the hardware above those EEH domains from its error state. The platform + also returns a PE Reset State of 5 (PE is unavailable) + with a PE Unavailable Info non-zero (temporarily + unavailable) while a recovery is in progress. + + + + + R1--6. + + The platform must own (be responsible for) + fault isolation for all errors that occur in the I/O fabric (that is, down to + the IOA; including errors that occur on that part of the I/O fabric which is + within a PE’s domain). + + + + + R1--7. + + For the EEH option with the PCI + Hot Plug option: All of the following must be true: + + + + If PCI Hot Plug operations are to be controlled by the OS to which + the PE is assigned, then the PE domain for the PCI Hot Plug entity and the PCI + Hot Plug power domain must be the same. + + + + All PE domains must be totally encompassed by their respective PCI + Hot Plug power domain, regardless of the entity that controls the PCI Hot Plug + operation. + + + + + + + R1--8. + + All platforms that implement the + EEH option must enable that option by default for all PEs. + Implementation Notes: + + + See for requirements + relative to EEH requirements with LPAR. + + + + Defaulting to EEH enabled, as required by Requirement + does not imply that the platform has no + responsibility in assuring that all device drivers are EEH enabled or EEH safe + before allowing their the Bus Master, Memory Space or I/O Space bits in the PCI + configuration Command register of their IOA to be set to a 1. Furthermore, even + though a platform defaults its EEH option as enabled, as required by + Requirement does not imply that the + platform cannot disable EEH for a PE. See Requirement + for more information. + + + + + + + + + The following two figures show some examples of the concept of + Endpoint Partitioning. See also for + more information on the EEH option. + +
+ PE and DR Partitioning Examples for Conventional PCI and PCI-X HBs + + + + + + + + +
+ +
+ PE and DR Partitioning Examples for PCI Express HBs + + + + + + + + +
+
+ +
+ PCI Host Bridge (PHB) Architecture + The PHB architecture places certain requirements on PHBs. There + should be no conflict between this document and the PCI specifications, but if + there is, the PCI documentation takes precedence. The intent of this + architecture is to provide a base architectural level which supports the PCI + architecture and to provide optional constructs which allow for use of 32-bit + PCI IOAs in platforms with greater than 4 GB of system addressability. + + + + R1--1. + + All PHBs that implement + conventional PCI must be compliant with the most recent version of the + at the time of their design, including any + approved Engineering Change Requests (ECRs) against that document. + + + + + R1--2. + + All PHBs that + implement PCI-X must be compliant with the most + recent version of the at the time of + their design, including any approved Engineering Change Requests (ECRs) against + that document. + + + + + R1--3. + + All PHBs that + implement PCI Express must be compliant with the + most recent version of the at the + time of their design, including any approved Engineering Change Requests (ECRs) + against that document. + + + + + R1--4. + + All requirements + defined in for HBs must + be implemented by all PHBs in the platform. + + + + +
+ PHB Implementation Options + There are a few implementation options when it comes to + implementing a PHB. Some of these become requirements, depending on the + characteristics of the system for which the PHB is being designed. The options + affecting PHBs, include the following: + + + + The Enhanced I/O Error Handling (EEH) option enhances RAS + characteristics of the I/O and allows for smaller granularities of I/O + assignments to partitions in an LPAR environment. + + + + The Error Injection (ERRINJCT) option enhances the testing of the + I/O error recovery code. This option is required of bridges which implement the + EEH option. + + + + + + R1--1. + + All PHBs + for use in platforms which implement LPAR must support EEH, in support of virtualizations + requirements in . + + + + + R1--2. + + All PCI HBs designed for use in platforms + which will support PCI Express must support the PCI extended configuration + address space and the MSI option. + + + +
+ +
+ PCI Data Buffering and Instruction Queuing + Some PHB + implementations may include buffers or queues for DMA, + Load, and Store operations. These buffers are required to be transparent to the + software with only certain exceptions, as noted in this section. + Most + processor accesses to System Memory go through the processor data cache. When + sharing System Memory with IOAs, hardware must maintain consistency with the + processor data cache and the System Memory, as defined by the requirements in + . + + + + R1--1. + + PHB implementations which + include buffers or queues for DMA, Load, and + Store operations must make sure that these are transparent to the + software, with a few exceptions which are allowed by the PCI architecture, by + , and by . + + + + + R1--2. + + PHBs must accept up to a 128 byte MMIO + Loads, and must do so without compromising performance + of other operations. + + + + +
+ PCI <emphasis>Load</emphasis> and <emphasis>Store</emphasis> Ordering + For the platform Load and + Store ordering requirements, see + and the + appropriate PCI specifications (per Requirements + , + , and + ). Those requirements will, for most + implementations, require strong ordering (single threading) of all + Load and Store operations through the PHB, + regardless of the address space on the PCI bus to which they are targeted. + Single threading through the PHB means that processing a + Load requires that the PHB wait on the Load + response data of a Load issued on the PCI bus prior to + issuing the next Load or Store on + the PCI bus. +
+ +
+ PCI DMA Ordering + For the platform DMA ordering requirements, see the requirements in + this section, in , and the appropriate + PCI specifications (per Requirements + , + , and + ). + In general, the ordering for DMA path operations from the I/O bus + to the processor side of the PHB is independent from the + Load and Store path, with the exception stated + in Requirement . Note that in the + requirement, below, a read request is the initial request + to the PHB and the read completion is the data phase of + the transaction (that is, the data is returned). + + + + R1--1. + + (Requirement Number Reserved + For Compatibility) + + + + + R1--2. + + (Requirement Number Reserved + For Compatibility) + + + + + R1--3. + + (Requirement Number Reserved + For Compatibility) + + + + + R1--4. + + The hardware must make sure that + a DMA read request from an IOA that specifies any byte address that has been + written by a previous DMA write operation (as defined by the untranslated PCI + address) does not complete before the DMA write from the previous DMA write is + in the coherency domain. + + + + + R1--5. + + (Requirement Number Reserved + For Compatibility) + + + + + R1--6. + + The hardware must make sure that + all DMA write data buffered from an IOA, which is destined for system memory, + is in the platform’s coherency domain prior to delivering data from a + Load operation through the same PHB which has come after + the DMA write operation(s). + + + + + R1--7. + + The hardware must make sure that + all DMA write data buffered from an IOA, which is destined for system memory, + is in the platform’s coherency domain prior to delivering an MSI from + that same IOA which has come after the DMA write operation(s). + + + + + Architecture Notes: + + + + Requirement clarifies + (and may tighten up) the PCI architecture requirement that the read be to the + “just-written” data. + + + + The address comparison for determining whether the address of the + data being read is the same as the address of that being written is in the same + cache line is based on the PCI address and not a TCE-translated address. This + says that the System Memory cache line address will be the same also, since the + requirement is directed towards operations under the same PHB. However, use of + a DMA Read Request and DMA Write Request that use different PCI addresses (even + if they hit the same System Memory address) are not required to be kept in + order (see Requirement ). So, for + example, Requirement says that split + PHBs that share the same data buffers at the system end do not have to keep DMA + Read Request following a DMA Write Request in order when they do not traverse + the same PHB PCI bus (even if they get translated to the same system address) + or when they originate on the same PCI bus but have different PCI bus addresses + (even if they get translated to the same system address). + + + + Requirement is the only + case where the Load and Store paths + are coupled to the DMA data path. This requirement guarantees that the software + has a method for forcing DMA write data out of any buffers in the path during + the servicing of a completion interrupt from the IOA. Note that the IOA can + perform the flush prior to the completion interrupt, via Requirement . That is, the IOA can issue a read request + to the last word written and wait for the read completion data to return. When + the read is complete, the data will have arrived at the destination. In + addition, the use of MSIs, instead of LSIs, allows for a programming model for + IOAs where the interrupt signalling itself pushes the last DMA write to System + Memory, prior to the signalling of the interrupt to the system (see Requirement + ). + + + + A DMA read operation is allowed to be processed prior to the + completion of a previous DMA read operation, but is not required to be. + + + +
+ +
+ PCI DMA Operations and Coherence + The I/O is not aware of the setting of the coherence required bit + when performing operations to System Memory, and so the PHB needs to assume + that the coherency is required. + + + + R1--1. + + I/O transactions to System Memory through a PHB must be made with coherency required. + + + +
+ +
+ +
+ Byte Ordering Conventions + LoPAR platforms operate with either Big-Endian (BE) or + Little-Endian addressing. In Big-Endian systems, the address of a word in + memory is the address of the most significant byte (the “big” + end) of the word. Increasing memory addresses will approach the least + significant byte of the word. In Little-Endian (LE) addressing, the address of + a word in memory is the address of the least significant byte (the + “little” end) of the word. See also + . + The PCI bus itself can be thought of as not inherently having an + endianess associated with it (although its numbering convention indicates LE). + It is the IOAs on the PCI bus that can be thought of as having endianess + associated with them. Some PCI IOAs will contain a mode bit to allow them to + appear as either a BE or LE IOA. Some IOAs will even have multiple mode bits; + one for each data path (Load and Store versus DMA). In addition, some IOAs may + have multiple concurrent apertures, or address ranges, where the IOA can be + accessed as a LE IOA in one aperture and as a BE IOA in another. + + + + R1--1. + + When the + processor is operating in the Big-Endian mode, the platform design must produce the results + indicated in while issuing + Load and Store operations to various entities + with various endianess. + + + + + R1--2. + + When performing DMA operations through a + PHB, the platform must not modify the data during the transfer process; the + lowest addressed byte in System Memory being transferred to the lowest + addressed byte on the PCI bus, the second byte in System Memory being + transferred as the second byte on the PCI bus, and so on. + + + + + + + Big-Endian Mode <emphasis>Load</emphasis> and + <emphasis>Store</emphasis> Programming Considerations + + + + + + + + Destination + + + + + Transfer Operation + + + + + + + + BE scalar entity: + For example, + TCE or BE register in a PCI IOA + + + Load or Store + + + + + LE scalar entity: + For example, + LE register in a PCI IOA or + PCI Configuration Registers + + + Load or Store Reverse + + + + +
+
+
+ PCI Bus Protocols + This section details the items from the + , + , and + documents where there is + variability allowed, and therefore further specifications, requirements, or + explanations are needed. + Specifically, details + specific PCI Express options and the requirements for usage of such in LoPAR + platforms. These requirements will drive the design of PHB implementations. See + the for more information. + + + PCI Express Optional Feature Usage in LoPAR Platforms + + + + + + + + + + PCI Express Option Name + + + + + Usage + + + + + Description + + + + + + Base + + + IBM Server + + + + + + Usage Legend : + NS = Not Supported; O = Optional (see also Description); OR = Optional but + Recommended; R = Required; SD = See Description + + + + + + + + Peripheral I/O Space + + + SD + + + SD + + + Required if the platform is going to support any Legacy + I/O devices, as defined by the , + otherwise support not required. The expectation is that Legacy I/O device + support by PHBs will end soon, so platform designers should not rely on this + being there when choosing I/O devices. + + + + + 64-bit DMA addresses + + + O + + + OR + SD + + + Implementation is optional, but is expected to be needed + in some platforms, especially those with more complex PCI Express fabrics. + Although the “ibm,dma-window” property can + implement 64-bit addresses, some OSs and Device Drivers may not be able to + handle values in the “ibm,dma-window” + property that are greater than or equal to 4 GB. Therefore, it is recommended + that 64-bit DMA addresses be implemented through the Dynamic DMA Window option + (see ). + + + + + Advanced Error Reporting (AER) + + + O + + + R + SD + + + This has implications in the IOAs selected for use in + the platform, as well as the PHB and firmware implementation. See the . + + + + + PCIe Relaxed Ordering (RO) and + ID-Based Ordering (IDO) + + + NS + + + NS + + + Enabling either of these options could allow DMA + transactions that should be dropped by an EEH Stopped State, to get to the + system before the EEH Stopped State is set, and therefore these options are not + to be enabled. Specifically, either of these could allow DMA transactions that + follow a DMA transaction in error to bypass the PCI Express error message + signalling an error on a previous packet. +   + Platform Implementation Note: It is + permissible for the platform (for example, the PHB or the nest) to re-order DMA + transactions that it knows can be re-ordered -- such as DMA transactions that + come from different Requester IDs or come into different PHBs -- as long as the + ordering with respect to error signalling is met. + + + + + 5.0 GT/s signalling (Gen 2) + + + O + + + OR + + +   + + + + + 8 GT signalling (Gen 3) + + + O + + + OR + + +   + + + + + TLP Processing Hints + + + O + + + O + + + If implemented, it must be transparent to OSs. + + + + + Atomic Operations (32 and 64 bit) + + + O + + + OR + SD + + + May be required if the IOAs being supported require it. + May specifically be needed for certain classes of IOAs such as + accelerators. + + + + + Atomic Operations (128 bit) + + + O + + + OR + SD + + + When 128 bit Atomic Operations are supported, 32 and 64 + bit Atomic Operations must be also supported. + + + + + Resizable BAR + + + O + + + O + + +   + + + + + Dynamic Power Allocation (DPA) + + + NS + + + NS + + + No support currently defined in LoPAR. + + + + + Latency Tolerance Reporting (LTR) + + + NS + + + NS + + + No support currently defined in LoPAR. + + + + + Optimized Buffer Flush/Fill (OBFF) + + + NS + + + NS + + + No support currently defined in LoPAR. + + + + + PCIe Multicast + + + NS + + + NS + + + No support currently defined in LoPAR. + + + + + Alternative Routing ID Interpretation (ARI) + + + O + + + SD + + + Required when the platform will support PCI Express IOV IOAs. + + + + + Access Control Services (ACS) + + + SD + + + SD + + + It is required that peer to peer operation between IOAs + be blocked when LPAR is implemented and those IOAs are assigned to different + LPAR partitions. For switches below a PHB, when the IOA functions below the + switch may be assigned to different partitions, this blocking is provided by + ACS in the switch. This is required even in Base platforms, if the above + conditions apply. + + + + + Function Level Reset (FLR) + + + SD + + + SD + + + Required when a PE consists of something other than a + full IOA. For example, if each function of a multi-function IOA each is in its + own PE. An SR-IOV Virtual Function (VF) may be one such example. + + + + + End-to-End CRC (ECRC) + + + O + + + R + SD + + + This has implications in the IOAs selected for use in + the platform, as well as the PHB and firmware implementation. See the + . + + + + + Internal Error Reporting + + + OR + SD + + + OR + SD + + + Implement where appropriate. Platforms need to consider + this for platform switches, also. PHBs may report internal errors to firmware + using a different mechanism outside of this architecture. + + + + + Address Translation Services (ATS) + + + NS + + + NS + + + LoPAR does not support ATS, because the invalidation + and modification of the Address Translation and Protection Table (ATPT) -- + called the TCEs in LoPAR -- is a synchronous operations, whereas the ATS + invalidation requires a more asynchronous operation. + + + + + Page Request Interface (PRI) + + + NS + + + NS + + + Requires ATS, which is not supported by LoPAR. + + + + + Single Root I/O Virtualization (SR-IOV) + + + O + + + OR + + + It is likely that most server platforms will need to be + enabled to use SR-IOV IOAs. + + + + + Multi-Root I/O Virtualization (MR-IOV) + + + SD + + + SD + + + Depending on how this is implemented, an MR-IOV device + is likely to look like an SR-IOV device to an OS (with the platform hiding the + Multi-root aspects). PHBs may be MR enabled or the MR support may be through + switches external to the PHBs. + + + + +
+
+ +
+ Programming Model + Normal memory mapped Load and Store instructions are used to access + a PHB’s facilities or PCI IOAs on the I/O side of the PHB. + defines the addressing model. + Addresses of IOAs are passed by OF via the OF device tree. + + + + R1--1. + + If a PHB defines any registers that are + outside of the PCI Configuration space, then the address of those registers + must be in the Peripheral Memory Space or Peripheral I/O Space for that PHB, or + must be in the System Control Area. + + + + + PCI + master DMA transfers refer to data transfers between a PCI master IOA and + another PCI IOA, or System Memory, where the PCI master IOA supplies the + addresses and controls all aspects of the data transfer. Transfers from a PCI + master to the PCI I/O Space are essentially ignored by a PHB (except for + address parity checking). Transfers from a PCI master to PCI Memory Space are + either directed at PCI Memory Space (for peer to peer operations) or need to be + directed to the host side of the PHB. DMA transfers directed to the host side + of a PHB may be to System Memory or may be to another IOA via the Peripheral + Memory Space of another HB. Transfers that are directed to the Peripheral I/O + Space of another HB are considered to be an addressing error (see + ). For information about decoding these address spaces + and the address transforms necessary, see + . +
+ +
+ Peer-to-Peer Across Multiple PHBs + This architecture does not architect peer-to-peer traffic between + two PCI IOAs when the operation traverses multiple PHBs. + + + + R1--1. + + The platform must prevent Peer-to-Peer + operations that would cross multiple PHBs. + + + +
+ +
+ Dynamic Reconfiguration of I/O + Disconnecting or connecting an I/O subsystem while the system is + operational and then having the new configuration be operational, including any + new added subsystems, is a subset of Dynamic Reconfiguration (DR). + Some platforms may also support plugging/unplugging of PCI IOAs + while the system is operational. This is another subset of DR. + DR is an option and as such, is not required by this architecture. + Attempts to change the hardware configuration on a platform that does not + enable configuration change, whose OS does not support that configuration + change, or without the appropriate user configuration change actions may + produce unpredictable results (for example, the system may crash). + PHBs in platforms that support the PCI Hot Plug Dynamic + Reconfiguration (DR) option may have some unique design considerations. For + information about the DR options, see . +
+ +
+ Split Bridge Implementations + In some platforms the PHB may be split into two pieces, separated + by a cable or fiber optics. The piece that is connected to the system bus (or + switch) and which generates the interconnect is called the Hub. There are + several implications of such implementations and several requirements to go + along with these. + +
+ Coherency Considerations with IOA to IOA Communications + via System Memory + Bridges which are split across multiple chips may introduce a large + enough latency between the time DMA write data is accepted by the PHB and the + time that previously cached copies of the same System Memory locations are + invalidated, and this latency needs to be taken into consideration in designs, + as it can introduce the problems described below. This is not a problem if the + same PCI address is used under a single PHB by the same or multiple IOAs, but + can be a problem under any of the following conditions: + + + + The same PCI address is used by different IOAs under different + PHBs. + + + + Different PCI addresses are used which access the same System + Memory coherency block, regardless of whether the IOA(s) are under the same PHB + or not; for example: + + + Two different TCEs accessing the same System Memory coherency + block. + + + + + + An example scenario where this could be a problem is as + follows: + + + + Device 1 does a DMA read from System Memory address x using PCI + address y + + + + Device 2 (under same PHB as Device 1 -- the devices could even + be different function in the same IOA) does a DMA write to System Memory + address x using PCI address z. + + + + Device 2 attempts to read back System Memory address x before + the time that its previous DMA write is globally coherent (that is, before the + DMA write gets to the Hub and an invalidate operation on the cache line + containing that data gets back down to the PHB), and gets the data read by + Device 1 rather than what it just wrote. + + + + Another example scenario is as follows: + + + + Device 1 under PHB 1 does a DMA read from System Memory location + x. + + + + Device 2 under PHB 2 does a DMA write to System Memory location + x and signals an interrupt to the system. + + + + The interrupt bypasses the written data which is on its way to + the coherency domain. + + + + The device driver for Device 2 services the interrupt and + signals Device 1 via a Store to Device 1 that the data is there at location + x. + + + + Device 1 sees the Store before the invalidate operation on the + cache line containing the data propagates down to invalidate the previous + cached copy of x, and does a DMA read of location x using the same address as + in step (1), getting the old copy of x instead of the new copy. + + + + This last example is a little far-fetched since the propagation + times should not be longer than the interrupt service latency time, but it is + possible. In this example, the device driver should do a Load to Device 2 + during the servicing of the interrupt and wait for the Load results before + trying to signal Device 1, just the way that this device driver would to a Load + if it was a program which was going to use the data written instead of another + IOA. Note that this scenario can also be avoided if the IOA uses a PCI Message + Signalled Interrupt (MSI) rather than the PCI interrupt signals pins, in order + to signal the interrupt (in which case the Load operation + is avoided). + + + + R1--1. + + A DMA read to a PCI address + which is different than a PCI address used by a previous DMA write or which is + performed under a different PHB must not presume that a previous DMA write is + complete, even if the DMA write is to the same System Memory address, unless + one of the following is true: + + + + The IOA doing the DMA write has followed that write by a DMA read + to the address of the last byte of DMA write data to be flushed (the DMA read + request must encompass the address of the last byte written, but does not need + to be limited to just that byte) and has waited for the results to come back + before an IOA is signaled (via peer-to-peer operations or via software) to + perform a DMA read to the same System Memory address. + + + + The device driver for the IOA doing the DMA write has followed + that write by a Load to that IOA and has waited for the + results to come back before a DMA read to the same System Memory address with a + different PCI address is attempted. + + + + The IOA doing the DMA write has followed the write with a PCI + Message Signalled Interrupt (MSI) as a way to interrupt the device driver, and + the MSI message has been received by the interrupt controller. + + + + + +
+
+
+ +
+ I/O Bus to I/O Bus Bridges + The PCI bus architecture was designed to allow for bridging to other + slower speed I/O buses or to another PCI bus. The requirements when bridging + from one I/O bus to another I/O bus in the platform are defined below. + + + + R1--1. + + All bridges must comply with the + bus specification(s) of the buses to which they are attached. + + + + +
+ What Must Talk to What + Platforms are not required to support peer to peer operations + between IOAs. IOAs on the same shared bus segment will generally be able to do + peer to peer operations between themselves. Peer to peer operations in an LPAR + environment, when the operations are between IOAs that are not in the same + partition, is specifically prohibited (see Requirement + ). +
+
+ PCI to PCI Bridges + This architecture allows the use of PCI to PCI bridges and + PCI Express switches in the platform. TCEs are used with the IOAs attached to + the other side of the PCI to PCI bridge or PCI Express switch when those IOAs + are accessing something on the processor side of the PHB. After configuration, + PCI to PCI bridges and PCI Express switches are basically transparent to the + software as far as addressing is concerned (the exception is error handling). + For more information, see the appropriate PCI Express switch + specification. + + + + R1--1. + + Conventional PCI to PCI bridges used on + the base platform and plug-in cards must be compliant with the most recent + version of the at the time of the + platform design, including any approved Engineering Change Requests (ECRs) + against that document. PCI-X to PCI-X bridges used on the base platform and + plug-in cards must be compliant with the most recent version of the + at the time of the platform design, + including any approved Engineering Change Requests (ECRs) against that + document. + + + + + R1--2. + + PCI Express to PCI/PCI-X and PCI/PCI-X to + PCI Express bridges used on the base platform and plug-in cards must be + compliant with the most recent version of the + at the time of the platform design, + including any approved Engineering Change Requests (ECRs) against that + document. + + + + + R1--3. + + PCI Express switches used on the base + platform and plug-in cards must be compliant with the most recent version of + the at the time of the platform + design, including any approved Engineering Change Requests (ECRs) against that + document. + + + + + R1--4. + + Bridges + and switches used in platforms which will support PCI + Express IOAs beneath them must support pass-through of PCI configuration cycles + which access the PCI extended configuration space. + Software and Platform Implementation Notes: + + + + Bridges used on plug-in cards that do not follow Requirement + will presumably allow for the + operation of their IOAs on the plug-in card, even though not supporting the PCI + extended configuration address space, because the card was designed with the + bridges and IOAs in mind. + + + + Determination of support of the PCI configuration address space + is via the “ibm,pci-config-space-type” + property in the IOA's node. + + + + + + + R1--5. + + Bridges and switches used in platforms + which will support PCI Express IOAs beneath them must support 64-bit + addressing. + + + +
+
+ +
+ Bridge Extensions +
+ Enhanced I/O Error Handling (EEH) Option + The EEH option uses the following terminology. + PE A Partitionable Endpoint. This refers to the granule that is + treated as one for purposes of EEH recovery and for assignment to an OS image + (for example, in an LPAR environment). Note that the PE granularity supported + by the hardware may be finer than is supported by the firmware. See also + . A PE may be any one of the + following: + A single-function or multi-function IOA + A set of IOAs and some piece of I/O fabric above the IOAs that + consists of one or more bridges or switches. + EEH Stopped state The state of a PE being in both the MMIO Stopped + state and DMA Stopped state. + MMIO Stopped state The state of the PE which will discard any MMIO + Store s to that PE, and will return all-1's data for + Load s to that PE. If the PE is in the MMIO Stopped state + and EEH is disabled, then a Load will also return a + machine check to the processor that issued the Load, for + the Load that had the initial error and while the PE + remains in the MMIO Stopped state. + DMA Stopped state The state of the PE which will block any further + DMA requests from that PE (DMA completions that occur after the DMA Stopped + state is entered that correspond to DMA requests that occurred before the DMA + Stopped state is entered, may be completed). + Failure A detected error between the PE and the system (for + example, processor or memory); errors internal to the PE are not considered + failures unless the PE signals the error via a normal I/O fabric error + signalling protocol. (for example, SERR or ERR_FATAL). + The Enhanced I/O Error Handling (EEH) option is defined primarily + to enhance the system recoverability from failures that occur during + Load and Store operations. In addition, + certain failures that are normally non-recoverable during DMA are prevented + from causing a catastrophic failure to the system (for example, a conventional + PCI address parity error). + The basic concept behind the EEH option is to turn all failures + that cannot be reported to the IOA, into something that looks like a + conventional PCI Master Abort (MA) errorA conventional PCI MA error is where the + conventional PCI IOA does not respond as a target with a device select + indication (that is, the IOA does not respond by activating the DEVSEL signal + back to the master). For PCI Express, the corresponding error is Unsupported + Request (UR). on a Load or Store operation to the PE during + and after the failure; responding with all-1’s data and no error + indication on a Load instruction and ignoring + Store instructions. The MA error should be handled by a device + driver, so this approach should just be an extension to what should be the + error handling without this option implemented. + The following is the general idea behind the EEH option: + + + + On a failure that occurs in an operation between the PHB and + PE: + + + + Put the PE into the MMIO Stopped and DMA Stopped states (also + known as the EEH Stopped state). This is defined as a state where the PE is + prevented from doing any further operations that could corrupt the system; + which for the most part means blocking DMA from the PE and preventing load and + store completions to the PE. + + + + While the PE is in the MMIO Stopped state, if a + Load or Store is targeted to that PE, then + return all-1’s data with no error indication on a + Load and discard all Stores to that PE. That + is, essentially treat the Load or + Store the same way as if a MA error was received on that + operation. + + + + The device driver and OS recovers a PE by removing it from the + MMIO Stopped state (keeping it in the DMA Stopped state) and doing any + necessary loads to the PE to capture PE state, and then either doing the + necessary stores to the PE to set the appropriate state before removing the PE + from the DMA Stopped state and continuing operations, or doing a reset of the + PE and then re-initializing and restarting the PE.Most + device drivers will implement a reset and + restart in order to assure a clean restart of + operations. + + + + + + In order to make sure that there are no interactions necessary + between device drivers during recovery operations, each PE will have the + capability of being removed from its MMIO Stopped and DMA Stopped states + independent from any other PE which is in the MMIO Stopped or DMA Stopped + state. + + + + In order to take into account device drivers which do not + correctly implement MA recovery, make sure that the EEH option can be enabled + and disabled independently for each PE.LPAR + implementations limit the capability of + running with EEH disabled (see virtualization rsequirements in + ). + + + + EEH, as defined, only extends to operations between the processor + and a PE and between a PE and System Memory. It does not extend to direct IOA + to IOA peer to peer operations. + + + + Hardware changes for this option are detailed in the next section. + RTAS changes required are detailed in . + +
+ EEH Option Requirements + Although the EEH option architecture may be extended to other I/O + topologies in the future, for now this recovery architecture will be limited to + PCI. + In order to be able to test device driver additional code for the + EEH-enabled case, the EEH option also requires the Error Injection option be + implemented concurrently. + The additional requirements on the hardware for this option are as + follows. For the RTAS requirements for this option, see + . + + + + R1--1. + + For the EEH option: + A platform must implement the Error Injection option concurrently + with the EEH option, with an error injection granularity to the PE level. + + + + + R1--2. + + For the EEH option: + If a platform is going to implement the EEH option, then the I/O + topology implementing EEH must only consist of PCI components. + + + + + R1--3. + + For the EEH option: + The hardware must provide a way to independently enable and disable + the EEH option for each PE with normal processor Load + and Store + instructions, and must provide the capability of doing this while not + disturbing operations to other PEs in the platform. + + + + + R1--4. + + For the EEH option: The hardware + fault isolation register bits must be set the same way on errors when the EEH + option is enabled as they were when the EEH option is not implemented or when + it is implemented but disabled. + + + + + R1--5. + + For the EEH option: Any + detected failure to/from a PE must set both the MMIO Stopped and DMA Stopped + states for the PE, unless the error that caused the failure can be reported to + the IOA in a way that the IOA will report the error to its device driver in a + way that will avoid any data corruption. + + + + + R1--6. + + For the EEH + option: If an + I/O fabric consists of a hierarchy of components, then when a failure is + detected in the fabric, all PEs that are downstream of the failure must enter + the MMIO Stopped and DMA Stopped states if they may be affected by the + failure. + + + + + R1--7. + + For the EEH + option: While a PE has its EEH option enabled, if a failure occurs, + the platform must not propagate it to the system as any type of error (for + example, as an SERR for a PE which is a conventional PCI-to-PCI bridge). + + + + + R1--8. + + For the EEH option: + From the time that the MMIO Stopped state is entered for a PE, the + PE must be prevented from responding to Load and Store operations including the + operation that caused the PE to enter the MMIO Stopped state; a Load operation + must return all-1’s with no error indication and a Store operation must + be discarded (that is, Load and Store + operations being treated like they received a conventional PCI + Master Abort error), until one of the following is true: + + + + The ibm,set-eeh-option RTAS call is called + with function 2 (Release PE for MMIO + Load /Store operations). + + + + The ibm, set-slot-reset RTAS call is + called with function 0 (Deactivate the reset signal to + the PE). + + + + The power is cycled (off then on) to the PE. + + + + The partition or system is rebooted. + + + + + + + R1--9. + + For the EEH option: + From the time that the DMA Stopped state is entered for a PE, the + PE must be prevented from initiating a new DMA request or completing a DMA + request that caused the PE to enter the DMA Stopped state (DMA requests that + were started before the DMA Stopped State is entered may be completed), and + including MSI DMA operations, until one of the following is true: + + + + The ibm,set-eeh-option RTAS call is called + with function 3 (Release PE for DMA operations). + + + + The ibm, set-slot-reset RTAS call is + called with function 0 (Deactivate the reset signal to + the PE). + + + + The power is cycled (off then on) to the PE. + + + + The partition or system is rebooted. + + + + + + + R1--10. + + For the EEH option: + The hardware must provide the capability to the firmware to + determine, on a per-PE basis, that a failure has occurred which has caused the + PE to be put into the MMIO Stopped and DMA Stopped states and to read the + actual state information (MMIO Stopped state and DMA Stopped state). + + + + + R1--11. + + For the EEH option: + The hardware must provide the capability of separately enabling and + resetting the DMA Stopped and MMIO Stopped states for a PE without disturbing + other PEs on the platform. The hardware must provide this capability without + requiring a PE reset and must do so through normal processor + Store instructions. + + + + + R1--12. + + For the EEH option: The hardware + must provide the capability to the firmware to deactivate the reset to each PE, + independent of other PEs, and the hardware must provide the proper controls on + the reset transitions in order to prevent failures from being introduced into + the platform by the changing of the reset. + + + + + R1--13. + + For the EEH option: The hardware + must provide the capability to the firmware to activate the reset to each PE, + independent of other PEs, and the hardware must provide the proper controls on + the reset transitions in order to prevent failures from being introduced into + the platform by the changing of the reset. + + + + + R1--14. + + For the EEH option: + The hardware must provide the capability to the firmware to read + the state of the reset signal to each PE. + + + + + R1--15. + + For the EEH option: When a PE is + put into the MMIO Stopped and DMA Stopped states, it must be done in such a way + to not introduce failures that may corrupt other parts of the platform. + + + + + R1--16. + + For the EEH option: + The hardware must allow firmware access to internal bridge and I/O + fabric control registers when any or all of the PEs are in the MMIO Stopped + state. + Platform Implementation Note: It is expected + that bridge and fabric control registers will have their own PE state separate + from the PEs for IOAs. + + + + + R1--17. + + For the EEH + option: A PE that supports the EEH option must not share an + interrupt with another PE in the platform. + Hardware Implementation Notes: + + + + Requirement means that + the hardware must always update the standard PCI error/status registers in the + bus’ configuration space as defined by the bus architecture, even when + the EEH option is enabled. + + + + The type of error information trapped by the hardware when a PE + is placed into the MMIO Stopped and DMA Stopped states is implementation + dependent. It is expected that the system software will do an check-exception + or ibm,slot-error-detail RTAS call to gather the error information when a + failure is detected. + + + + A DMA operation (Read or Write) that was initiated before a Load, + Store, or DMA error, does not + necessarily need to be blocked, as it was not a result of the + Load, Store, or DMA that failed. The normal + PCI Express ordering rules require that an ERR_FATAL or ERR_NONFATAL from a + failed Store or DMA error, or a + Load Completion with error status, will reach the PHB prior to any + DMA that might have been kicked-off in error as a result of a failed + Load or Store or a Load + or Store that follows a failed Load + or Store. This means that as long as the PHB processes + an ERR_FATAL, ERR_NONFATAL, or Load Completion which + indicates a failure, prior to processing any more DMA operations or + Load Completions, and puts the PE into the MMIO and Stopped DMA + Stopped states, implementations should be able to block DMA operations that + were kicked-off after a failing DMA operation and allow DMA operations that + were kicked off before a failing DMA operation without violating the normal PCI + Express ordering rules. + + + + In reference to Requirements + , and + , PCI Express implementations may choose to + enter the MMIO Stopped and DMA Stopped states even if an error can be reported + back to the IOA. + + + + + + + R1--18. + + For the EEH option: If + the device driver(s) for any IOA(s) in a PE in the platform are EEH unaware + (that is may produce data integrity exposures due to a MMIO Stopped or DMA + Stopped state), then the firmware must prevent the IOA(s) in such a PE from + being enabled for operations (that is, do not allow the Bus Master, Memory + Space or I/O Space bits in the PCI configuration Command register from being + set to a 1) while EEH is enabled for that PE, and instead of preventing the PE + from being enabled, may instead turn off EEH when such an enable is attempted + without first an attempt by the device driver to enable EEH (by the + ibm,set-eeh-option ), providing such EEH disablement does not + violate any other requirement for EEH enablement (for example, virtualization + requirement in ). + Software Implementation Note: To be EEH + aware, a device driver does not need to be able to recover from an MMIO Stopped + or DMA Stopped state, only recognize the all-1's condition and not use data + from operations that may have occurred since the last all-1's checkpoint. In + addition, the device driver under such failure circumstances needs to turn off + interrupts (using the ibm,set-int-off RTAS call or by + resetting the PE and keeping it reset with ibm,set-slot-reset or + ibm,slot-error-detail) in order to make + sure that any (unserviceable) interrupts from the PE do not affect the system. + Note that this is the same device driver support needed to protect against an + IOA dying or against a no-DEVSEL type error (which may or may not be the result + of an IOA that has died). + + + +
+ +
+ Slot Level EEH Event Interrupt Option + Some platform implementations may allow asynchronous notification + of EEH events via an external interrupt. This is called the Slot Level EEH + Event Interrupt option. When implemented, the platform will implement the + “ibm,io-events-capable” property in the + nodes where the EEH control resides, and the ibm,set-eeh-option + RTAS call will implement function 4 to enable the + EEH interrupt for each of these nodes and function 5 to disable the EEH + interrupt for each of these nodes (individual control by node). Calling the + ibm,set-eeh-option RTAS call with function 4 or function + 5 when the node specified does not implement this capability will return a -3, + indicating invalid parameters. + The interrupt source specified in the + ibm,io-events child must be enabled (in addition to any individual + node enables) via the ibm,int-on RTAS call and the + priority for that interrupt, as set in the XIVE by the + ibm,set-xive RTAS call, must be something other than 0xFF, in order + for the external interrupt to be presented to the system. + The “ibm,io-events-capable” + property, when it exists, contains 0 to N interrupt specifiers (per the + definition of interrupt specifiers for the node's interrupt parent). When no + interrupt specifiers are specified by the “ibm,io-events-capable” + property, then the interrupt, if enabled, is signaled via the interrupt specifier given in the + ibm,io-events child node of the /events + node. + + + + R1--1. + + For the Slot Level EEH Event + Interrupt option: All of the following must be true: + + + + The platform must implement the “ibm,io-events-capable” + property in all device tree nodes which represent bridge where EEH is implemented and for which the EEH + io-event interrupt is to be signaled. + + + + The platform must implement functions 4 and 5 of the + ibm,set-eeh-option RTAS call for all PEs under nodes that contain + the “ibm,io-events-capable” property. + + + + + +
+
+ +
+ Error Injection (ERRINJCT) Option + The Error Injection (ERRINJCT) option is defined primarily to test + enhanced error recovery software. As implemented in the I/O bridge, this option + is used to test the software which implements the recovery which is enabled by + the EEH option in that bridge. Specifically, the ioa-bus-error and + ioa-bus-error-64 functions + of the ibm,errinjct RTAS call are used to inject errors + onto each PE primary bus, which in turn will cause certain actions on the bus + and certain actions by the PE, the EEH logic, and by the error recovery + software. + +
+ ERRINJCT Option Hardware Requirements + Although the ioa-bus-error and + ioa-bus-error-64 functions of the + ibm,errinjct RTAS call may be extended to other I/O buses and PEs in + the future, for now this architecture will be limited to PCI buses. + The type of errors, and the injection qualifiers, place the + following additional requirements on the hardware for this option. + + + + R1--1. + + For the + ioa-bus-error and + ioa-bus-error-64 functions of the Error Injection option: + If a platform is going to implement either of these functions of this option, then + the I/O topology must be PCI. + + + + + R1--2. + + For the + ioa-bus-error and + ioa-bus-error-64 functions of the Error Injection option: + The hardware must provide a way to inject the required errors for + each PE primary bus, and the errors must be injectable independently, without + affecting the operations on the other buses in the platform. + + + + + R1--3. + + For the + ioa-bus-error and + ioa-bus-error-64 functions of the Error Injection option: + The hardware must provide a way to set up for the injection of the + required errors without disturbing operations to other buses outside the + PE. + + + + + R1--4. + + For the + ioa-bus-error and + ioa-bus-error-64 functions of the Error Injection option: + The hardware must provide a way to the firmware to set up the + following information for the error injection operation by normal processor + Load andStore instructions: + + + + Address at which to inject the error + + + + Address mask to mask off any combination of the least significant + 24 (64 for the ioa-bus-error-64 function) bits of the + address + + + + PE primary bus number which is to receive the error + + + + Type of error to be injected + + + + + + + + R1--5. + + For the + ioa-bus-error and + ioa-bus-error-64 functions of the Error Injection option: + The platform must have the capability of selecting the errors + specified in when the bus directly + below the bridge injecting the error is a Conventional PCI or PCI-X Bus, and + the errors specified in when the bus + directly below the bridge injecting the error is a PCI Express link, and when + that error is appropriate for the platform configuration, and the platform must + limit the injection of errors which are inappropriate for the given platform + configuration. + Platform Implementation Note: As an example + of inappropriate errors to inject in Requirement + , consider the configuration where there is + an I/O bridge or switch below the bridge with the injector and that bridge + generates multiple PEs and when those PEs are assigned to different LPAR + partitions. In that case, injection of some real errors may cause the switches + or bridges to react and generate an error that affects multiple partitions, + which would be inappropriate. Therefore, to comply with Requirement + , the platform may either emulate some + errors in some configurations instead of injecting real errors on the link or + bus, or else the platform may not support injection at all to those PEs. + Another example where a particular error may be inappropriate is when there is + a heterogeneous network between the PHB and the PE (for example, a PCI Express + bridge that converts from a PCI Express PHB and a PCI-X PE). + + + Supported Errors for Conventional PCI, PCI-X Mode 1 + or PCI-X Mode 2 Error Injectors + + + + + + + + + + Operation + + + + + PCI Address Space(s) + + + + + Error (s) + + + + + Other Requirements + + + + + + + + Load + + + Memory, I/O, Config + + + Data Parity Error + + + All PCI-X adapters operating in Mode 2 and some + operating in Mode 1 utilize a double bit detecting, single bit correcting Error + Correction Code (ECC). In these cases, ensure that at least two bits are + modified to detect this error. + + + + + Address Parity Error + + + + + Store + + + Memory, I/O, Config + + + Data Parity Error + + + + + Address Parity Error + + + + + DMA read + + + Memory + + + Data Parity Error + + + All PCI-X adapters operating in Mode 2 and some + operating in Mode 1 utilize a double bit detecting, single bit correcting Error + Correction Code (ECC). In these cases, ensure that at least two bits are + modified to detect this error. + + + + + Address Parity Error + + + + + Master Abort + + +   + + + + + Target Abort + + +   + + + + + DMA write + + + Memory + + + Data Parity Error + + + All PCI-X adapters operating in Mode 2 and some + operating in Mode 1 utilize a double bit detecting, single bit correcting Error + Correction Code (ECC). In these cases, ensure that at least two bits are + modified to detect this error. + + + + + Address Parity Error + + + + + Master Abort + + +   + + + + + Target Abort + + +   + + + + +
+ + + Supported Errors for PCI Express Error Injectors + + + + + + + + + + Operation + + + + + PCI Address Space(s) + + + + + Error (s) + + + + + Other Requirements + + + + + + + + Load + + + Memory, I/O, Config + + + TLP ECRC Error + + + The TLP ECRC covers the address and data bits of a TLP. + Therefore, one cannot determine if the integrity error resides in the address + or data portion of a TLP. + + + + + Store + + + Memory, I/O, Config + + + TLP ECRC Error + + + + + DMA read + + + Memory + + + TLP ECRC Error + + + The TLP ECRC covers the address and data bits of a TLP. + Therefore, one cannot determine if the integrity error resides in the address + or data portion of a TLP. + + + + + Completer Abort or Unsupported Request + + + Inject the error that is injected on a TCE Page Fault. + + + + + DMA write + + + Memory + + + TLP ECRC Error + + + The TLP ECRC covers the address and data bits of a TLP. + Therefore, one cannot determine if the integrity error resides in the address + or data portion of a TLP. + + + + +
+ + + + + R1--6. + + For the + ioa-bus-error and + ioa-bus-error-64 functions of the Error Injection option: + The hardware must provide a way to inject the errors in + in a non-persistent manner (that is, at + most one injection for each invocation of the ibm,errinjct RTAS call). + + + + +
+ +
+ ERRINJCT Option OF Requirements + The Error Injection option will be disabled for all IOAs prior to + the OS getting control. + + + + R1--1. + + For the + ioa-bus-error and + ioa-bus-error-64 functions of the Error Injection option: + The OF must disable the ERRINJCT option for all PEs and all empty + slots on all bridges which implement this option prior to passing control to + the OS. + + + + + Hardware and Firmware Implementation Note: + The platform only needs the capability to setup the injection of one error at a + time, and therefore injection facilities can be shared. The + ibm,open-errinjct and ibm,close-errinjct are + used to make sure that only one user is using the injection facilities at a + time. +
+
+ +
+ Bridged-I/O EEH Support Option + If a platform requires multi-function I/O cards which are + constructed by placing multiple IOAs beneath a PCI to PCI bridge, then extra + support is needed to support such cards in an EEH-enabled environment. If this + option is implemented, then the ibm,configure-bridge RTAS + call will be implemented and therefore the + “ibm,configure-bridge” property will exist in the + rtas device node. + + + + R1--1. + + For the Bridged-I/O EEH + Support option: The platform must support the + ibm,configure-bridge RTAS call. + + + + + R1--2. + + For the Bridged-I/O EEH + Support option: The OS must provide the correct EEH coordination + between device drivers that control multiple IOAs that are in the same + PE. + + + +
+
+ diff --git a/Platform/ch_nonvolatile_memory.xml b/Platform/ch_nonvolatile_memory.xml new file mode 100644 index 0000000..fa3d2cc --- /dev/null +++ b/Platform/ch_nonvolatile_memory.xml @@ -0,0 +1,740 @@ + + + Non-Volatile Memory + + This chapter describes the requirements relating to Non-Volatile + Memory. Non-Volatile Memory is the repository for system information that must + be persistent across reboots and power cycles. + +
+ System Requirements + + + + R1--1. + + Platforms must implement at least 8 KB of + Non-Volatile Memory. The actual amount is platform dependent and must allow for + 4 KB for the OS. Platforms must provide an additional 4 KB for each installed + OS beyond the first. + + + + + R1--2. + + Non-Volatile Memory must maintain its + contents in the absence of system power. + + + + + R1--3. + + Firmware must reinitialize NVRAM to a + bootable state if NVRAM data corruption is detected. + + + + + R1--4. + + OSs must reinitialize their own NVRAM + partitions if NVRAM data corruption is detected. OSs may create free space from + the first corrupted NVRAM partition header to the end of NVRAM and utilize this + area to initialize their NVRAM partitions. + + + + + Hardware Implementation Note: The NVRAM terminology used in this + chapter goes back to historic implementations that have used battery-powered + RAM to implement the non-volatile memory. It should be understood that this is + not the only possible implementation. Implementers need to understand that + there are no limits on the frequency of writing to the non-volatile memory, so + certain technologies may not be applicable. Also, it should be noted that the + nvram-fetch and nvram-store RTAS + calls do not allow a “busy” Status return, and this may further + limit the implementation choices. + Software Implementation Note: Refer to + for information on accessing NVRAM. +
+ +
+ Structure + NVRAM is formatted as a set of NVRAM partitions that adhere to the + structure in . NVRAM partitions are + prefixed with a header containing signature, + checksum, length, and + name fields. The structure of the data field + is defined by the NVRAM partition creator/owner (designated by + signature and name). + + + + R1--1. + + NVRAM partitions must be structured as shown + in . + + + + + R1--2. + + All NVRAM space must be accounted for by + NVRAM partitions. + + + + + R1--3. + + All IBM-defined NVRAM partitions that are + intended to be IBM-unique must have names prefixed with the ASCII + representation of the four characters: ibm,. + + + + + Software Implementation Note: Although the data + areas of NVRAM partitions are not required to have error checking, it is + strongly recommended that the system software implement robust data structures + and error checking. Loss of NVRAM structures due to data corruption can be + catastrophic, potentially leading to OS reinstallation and/or complete system + initialization. +
+ +
+ Signatures + The signature field is used as the first level + of NVRAM partition identification. + lists all the currently defined signature types and their ownership classes. + The ownership class determines the permission of a particular system software + component to create and/or modify NVRAM partitions and/or NVRAM partition + contents. All NVRAM partitions may be read by any system software component, + but the ownership class has exclusive write permission. Global ownership gives + read/write permission to all system software components. These restrictions are + made to minimize the possibility of corruption of NVRAM during update + activities. + Hardware and Software Implementation Note: It is recommended that + NVRAM partitions be ordered on the signature field with the lowest value + signature NVRAM partition at the lowest NVRAM address (with the exception of + signature = 0x7F, free space). This will minimize the effect of NVRAM data + corruption on system operation. + + + NVRAM Structure + + + + + + + + + Field Name + + + + + Size + + + + + Description + + + + + + + + signature + + + 1 byte + + + The signature field is used to + identify the NVRAM partition type and provide some level of checking for + overall NVRAM contamination. Signature assignments are given in + . + + + + + checksum + + + 1 byte + + + The checksum field is included to + provide a check on the validity of the header. The checksum covers the + signature, length, and + name fields and is calculated (on a byte by byte or equivalent + basis) by: add, and add 1 back to the sum if a carry resulted as demonstrated + with the following program listing. + This checksum algorithm guarantees 0 to be an impossible + calculated value. A valid header cannot have a checksum of zero. + + + + + length + + + 2 bytes + + + The length field designates the + total length of the NVRAM partition, in 16-byte blocks, beginning with the + signature and ending with the last byte of the data area. A length of zero is + invalid. + Software Implementation Note: The + length field must always provide valid offsets to the + next header since an invalid length effectively causes the loss of access to + every NVRAM partition beyond it. + + + + + name + + + 12 bytes + + + The name field is a 12 byte string + (or a NULL-terminated string of less than 12 bytes) used to identify a + particular NVRAM partition within a signature group. In order to reduce the + likelihood of a naming conflict, each platform-specific or OS-specific NVRAM + partition name should be prefixed with a company name as specified under the + description of the “name” string in the + , that is, a company name string + in one of the three forms described in the reference, followed by a comma + (“,”). If the company name string is null, the name will be + interpreted as “other”. + Before assigning a new name to a NVRAM partition, software + should scan the existing NVRAM partitions and ensure that an unwanted name + conflict is not created. + + + + + data + + + length minus 16 bytes + + + The structure of the data area is + controlled by the creator/owner of the NVRAM partition. + + + + +
+ + + NVRAM Signatures + + + + + + + + + + + Signature (see note) + + + + + Signature Type + + + + + Ownership Class + + + + + # Required + + + + + Description + + + + + + + + 0x70 + + + System + + + Global + + + 1 + + + For configuration variables. + + + + + 0x7E + + + Vendor-defined + + + Global + + + 0 to n + + + “name” prefix required. + + + + + 0x7F + + + Free Space + + + Global + + + 0 to n + + + This signature is used to mark free space in the NVRAM + array. The name field of all signature 0x7F NVRAM + partitions must be set to 0x7...77. + + + + + 0xA0 + + + OS + + + Any OS + + + 0 to n + + + General OS usage. + + + + + Note: Any signature not defined above is reserved, and + signatures 0x02, 0x50, 0x51, 0x52, 0x71, and 0x72 are reserved for legacy + reasons. + + + + +
+
+ +
+ Architected NVRAM Partitions + +
+ System (0x70) + System NVRAM partitions are used for storing information + (typically, configuration variables) accessible to both OF and the OS. Refer to + for the definition of the contents of the + System NVRAM partition named common. + + + + R1--1. + + Every system NVRAM must contain a System + NVRAM partition with the NVRAM partition name = common. + + + + + R1--2. + + Data in the common + NVRAM partition must be stored as NULL-terminated strings of the form: + <name>=<string> and the + data area must be terminated with at least two NULL + characters. + + + + + R1--3. + + All names used in + the common NVRAM partition must be unique. + + + + + R1--4. + + Device and file specifications used in + the common NVRAM partition must follow IEEE Std 1275 + nomenclature conventions. + + + + +
+ System NVRAM Partition + The System NVRAM partition, with name = common, + contains information that is accessible to both OF and OSs. + The contents of this NVRAM partition are represented in the OF device tree as + properties (i.e., (name, value) + pairs) in the /options node. While OF is available, the + OS can alter the contents of these properties by using the + setprop client interface service. When OF is no longer available, + the OS can alter the contents of the System NVRAM partition itself, following + the rules below for the formats of the name and + value. Information is stored in the System NVRAM + partition as a sequence of (name, + value) pairs in the following format: + name = value + where name follows the rules defined in + and value follows the + rules defined in . The end of the + sequence of pairs is denoted by a NULL (0x00) byte. + +
+ Name + Since the data in the System NVRAM partition is an external + representation of properties of the /option node, the + name component must follow the rules for property names + as defined by Section 3.2.2.1.1 Property names of + ; i.e., a string of 1-31 printable + characters containing no uppercase characters or the characters + “/”, “\”, “:”, “[“, + “]” or “@”. In addition to these rules, a naming + convention is required for OS specific names to avoid name conflicts. Each such + name must begin with the OS vendor’s OUI followed by a + “,”; e.g., aapl,xxx or + ibm,xxx. This introduces separate name spaces for each vendor in which + it manages its own naming conventions. +
+ +
+ Value + The value component of System NVRAM partition data can contain an + arbitrary number of bytes in the range 0x01 to 0xFF, terminated by a NULL + (0x00) byte. Bytes in the range 0x01 to 0xFE represent themselves. In order to + allow arbitrary byte data to be represented, an encoding is used to represent + strings of 0x00 or 0xFF bytes. This encoding uses the 0xFF byte as an escape, + indicating that the following byte is encoded as: + bnnnnnnn + where b, the most-significant bit, is 0 to represent a sequence of + 0x00 bytes or 1 to represent a sequence of 0xFF bytes. nnnnnnn, the + least-significant 7 bits, is a binary number (in the range 0x01 to 0x7F) that + represents the number of repetitions of 0x00 or 0xFF. +
+ +
+ OF Configuration Variables + OF configuration variables control the operation of OF. In addition + to the standard configuration variables defined in + , other configuration variables are defined + in . While such variables are stored in the System + NVRAM partition as described above, they have additional rules placed on the + format of the value component. Each configuration variable is also represented + by a user interface word (of the same name) that returns stack value(s) when + that word is evaluated. Each also has a platform defined default value; the + absence of a configuration variable in the System NVRAM partition indicates + that the value is set to its default value. The format of the external + representation of configuration variables, and their stack representation, is + defined by Section 7.4.4.1 Configuration Variables of + ; the format depends upon the data type of + the configuration variable. Whereas the internal storage format is not defined + by , this architecture specifies them + as described below. The names of configuration variables are defined in , except as noted otherwise. + +
+ Boolean Configuration Variables + The value of a boolean configuration variable is represented in the + System NVRAM partition as the string “true” or + “false”. The following configuration variables are of type + boolean: + + + auto-boot? + + + diag-switch? + + + fcode-debug? + + + oem-banner? + + + oem-logo? + + + use-nvramrc? + + + little-endian? + + + real-mode? + + + menu? (see ). + + +
+ +
+ Integer Configuration Variables + The value of an integer configuration variable is represented in + the System NVRAM partition as a decimal number or a hexadecimal number preceded + by “0x”. The following configuration variables are of type + integer: + + + screen-#columns + + + screen-#rows + + + security-#badlogins + + + security-mode + + + selftest-#megs + + + real-base + + + real-size + + + virt-base + + + virt-size + + + load-base + + +
+ +
+ String Configuration Variables + The value of a string configuration variable is represented in the + System NVRAM partition as the characters of the string. Where multiple + “lines” of text are represented, each line is terminated by a + carriage-return (0x0D), a line-feed (0x0A), or carriage-return, line-feed + sequence (0x0D, 0x0A). The following configuration variables are of type + string: + + + boot-command [1] + + + boot-device [1] + + + boot-file [1] + + + diag-device [1] + + + diag-file [1] + + + input-device [1] + + + nvramrc [1] + + + oem-banner [1] + + + output-device [1] + + + security-password [1] + + + bootinfo-nnnnn [*] + + + reboot-command [*] + + +
+ +
+ Byte Configuration Variables + The value of a bytes configuration variable is represented by an + arbitrary number of bytes, using the encoding escape for values of 0x00 and + 0xFF. The following configuration variables are of type bytes: + + + oem-logo [1] + + +
+
+
+ +
+ DASD Spin-up Control + In order to reduce the boot time of platforms, a configuration + variable is defined to communicate from the platform to the OS to what extent + spin-up of hard disk drives can be overlapped. Disk drives generally draw more + current as the motors spin up to operating speed, thus the capacity of the + power supply limits the ability to spin up drives simultaneously. + The configuration variable + ibm,dasd-spin-interval indicates the minimum time, in seconds, that + must be allowed between initiating the spin-up of hard disk drives on the + platform. Presence of this variable potentially allows starting up a drive + prior to receiving completion status from a drive previously started. The + absence of this variable implies no platform knowledge regarding the capability + to overlap and, hence, the OS should wait for the appropriate device status + before proceeding to subsequent drives (no overlap). + + + + R1--1. + + If a platform wants to overlap spinning + up it's hard disk drives to improve boot performance, it must create the + ibm,dasd-spin-interval OF configuration variable in the + NVRAM signature 0x70 NVRAM partition named common and set + it equal to an integer that represents the minimum time, in seconds, that must + be allowed between initiating the spin-up of drives on the platform. + + + + + Firmware Implementation Note: The platform + should provide a user-friendly interface to this variable to allow for the + possibility of a user installing hard disks that do not conform to the original + setting of the variable. +
+
+ +
+ Free Space (0x7F) + + + + R1--1. + + All unused NVRAM space must be included + in a signature = 0x7F Free Space NVRAM partition. + + + + + R1--2. + + All Free Space NVRAM partitions must have + the name field set to 0x7...77. + + + +
+
+ +
+ NVRAM Space Management + The only NVRAM partitions whose size an OS can modify are OS and Free + Space signature NVRAM partitions. As NVRAM partitions are created and modified + by an OS, it is likely that free space will become fragmented; free space + consolidation may become necessary. + + + + R1--1. + + An OS must not move or delete any NVRAM + partition, except OS and Free Space signature NVRAM partitions. + + + + + R1--2. + + The NVRAM partition header checksum must be + calculated as shown in . + + + +
+ diff --git a/Platform/ch_numa.xml b/Platform/ch_numa.xml new file mode 100644 index 0000000..cac8904 --- /dev/null +++ b/Platform/ch_numa.xml @@ -0,0 +1,524 @@ + + + Non Uniform Memory Access (NUMA) Option + +
+ Summary of Extensions to Support NUMA + NUMA platforms to a first level approximation are simply a large + scale Symmetric Multi-Processor. However to tune system performance and to aid + in platform maintenance, the OS needs additional information and mechanisms. + These include: + + + + Associativity -- to determine the platform resource + groupings. + + + + Relative Performance Distances -- to determine the performance + between resources within different groupings. + + + + Performance Monitor -- to provide usage data on the NUMA + fabric. + + + + Dynamic Reconfiguration -- due to such causes as platform upgrade, + reallocation of resources, or a repair of a failure. + + + + There are two NUMA support options: the “NUMA” option + and its proper subset the “Associativity Information” + option. +
+ +
+ NUMA Resource Associativity + Associativity Codes represent the groupings of the various platform + resources into domains of substantially similar mean performance relative to + resources outside of that domain. Resources subsets of a given domain that + exhibit better performance relative to each other than relative to other + resources subsets, are represented as being members of a sub-grouping domain. + Such sub-domain grouping is represented to any level deemed significant by the + platform design. presents a simple + system configuration with one possible decomposition into associativity + domains. From the decomposition provided the + “ibm,associativity” value string for each resource is + enumerated. + +
+ Example NUMA configuration with + domains and corresponding <emphasis role="bold"><literal>“ibm,associativity”</literal></emphasis> + values + + + + + + + + +
+ + The OF Device Tree node for each allocable resource + (processor, memory region, and IO slot) conveys information about the resources + statically assigned to the client program; and contains the + “ibm,associativity” + property (see ). This property allows the client + program to determine the associativity between any two of it’s + resources. The greater the associativity the greater the expected performance + when using those two resources in a given operation. + The legal form of the “ibm,associativity” + property is dependent upon the setting of the + “ibm,architecture-vec-5” + property byte 5 bit 0. The bit value of zero allows the + “ibm,associativity” property string to be sequenced in + priority order; this form is being deprecated for new implementations in favor + of the form indicated by the + “ibm,architecture-vec-5” + property byte 5 bit 0 having the value of one in which the + “ibm,associativity” property string represents the + strict physical hierarchy of the platform. + When the LPAR option is also implemented, the partition virtual + resources may be mapped onto physical resources with in a very dynamic manor. + Given that the resource mapping to the associativity domain is substantially + consistent, the client program can make use of the associativity information to + on the average optimize performance. If the resource mapping to the + associativity domain is substantially inconsistent, then associativity + information for the resources is not provided to prevent erroneous operation. + If the long term mapping changes the client program can be made aware of the + new associativity information using the ibm,update-properties RTAS call (See + ). + + + + R1--1. + + For the NUMA or Associativity + Information option: The platform must include the + “ibm,associativity” in the OF device tree + memory node and the nodes of each processor, memory + region, and PCI bridge onto which IOAs may be plugged if the component is + dedicated to the partition. (The device tree node for a component that the + platform intends to virtualize should include an + “ibm,associativity” property if the associativity + domain information is substantially accurate.) + + + + + R1--2. + + For the NUMA option and SPLPAR + option: In the case that both the NUMA and SPLPAR options are + implemented, Requirement is modified + to remove processors from the list of system elements that must include the + respective properties or interfaces described by that requirement. (The + platform is encouraged to provide processor associativity information if it is + substantially accurate.) + + + + + The “ibm,associativity” + property contains one or more lists of numbers representing the + resource’s platform grouping domains. Each list, starts with a number + representing the domain number of the highest level grouping within which the + platform is capable of supporting direct access. This highest level may be a + NUMA collective or possibly a cluster of machines with direct DMA access. + Successive numbers represent sub-divisions of the previous higher level within + which the expected mean value of the performance relative to outside resources + is substantially similar. Implementations determine the number of levels that + they report, subject to Requirements + and . The lowest level always being + that of the allocable resource itself. The user of this information is + cautioned not to imply any specific physical/logical significance of the + various intermediate levels. + + + + R1--3. + + For the NUMA or Associativity + Information option: Differing levels of resource grouping represented in the + “ibm,associativity” property + must reflect statistically repeatable differences in the expected mean of + measured performance. + + + + + R1--4. + + For the NUMA or Associativity + Information option: The expected mean performance of any resource + of a given type within the same grouping domain represented in the + “ibm,associativity” property relative to + resources outside of that grouping domain must be substantially similar. + + + + The reason that the “ibm,associativity” + property may contain + multiple associativity lists is that a resource may be multiply connected into + the platform. This resource then has a different associativity characteristics + relative to its multiple connections. To determine the associativity between + any two resources, the OS scans down the two resources associativity lists in + all pair wise combinations counting how many domains are the same until the + first domain where the two list do not agree. The highest such count is the + associativity between the two resources. +
+ +
+ Relative Performance Distance + An OS applies its NUMA tuning techniques based upon associativity and + relative performance distance attributes. As a guide to relative performance + distance, RISC Platforms provide the “ibm,associativity-reference-points” + property. The information in this property represents a first order approximation to points + having associativity and relative performance distance characteristics deemed + to be of significant interest to optimizing client program performance. + The contents of the “ibm,associativity-reference-points” + property is dependent upon the setting of the + “ibm,architecture-vec-5” + property byte 5 bit 0. The bit value of zero allows the + “ibm,associativity-reference-points” property string + to indicate logical structure points; this form is being deprecated for new + implementations in favor of the form indicated by the + “ibm,architecture-vec-5” + property byte 5 bit 0 having the value of one in which the + “ibm,associativity-reference-points” property string + represents boundaries between associativity domains presented by the + “ibm,associativity” property containing + “near” and “far” resources. + + + + R1--1. + + For the NUMA or Associativity + Information option: The RTAS OF device tree node must contain the + “ibm,associativity-reference-points”. + + + + +
+ Form 0 + When the “ibm,architecture-vec-5” + property byte 5 bit 0 has the value of zero, the + “ibm,associativity-reference-points” property defines + reference points in the “ibm,associativity” + property (see ) which roughly correspond to + traditional notions of platform topology constructs. It is important for the + user to realize that these reference points are not exact and their + characteristics vary among implementations. + The first integer in the “ibm,associativity-reference-points” + property relates the 1 based ordinal in the associativity lists of the platform’s + “ibm,associativity” property associated + with the traditional notion of a symmetric multi-processor within a NUMA + platform. That is the level that represents building blocks of processors and + memory that have the following characteristics: + + + + An OS is likely to view all members having roughly uniform access + characteristics. + + + + Represents the highest level before an OS is likely to notice + major Non-Uniformity of access. + + + + The second integer in the “ibm,associativity-reference-points” + property relates the 1 based ordinal in the associativity lists of the platform’s + “ibm,associativity” property associated + with the traditional notion of a processor group which is sometimes packaged in + a multi-chip module. A processor group has similar characteristics to an SMP, + however, several processor groups get packaged densely within the same physical + enclosure forming an SMP. While the intra processor group accesses are + measurably greater than inter processor group accesses they are a second order + effect. + Subsequent ibm,associativity-reference-points entries are reserved. +
+ +
+ Form 1 + When the “ibm,architecture-vec-5” + property byte 5 bit 0 has the value of one, the + “ibm,associativity-reference-points” property + indicates boundaries between associativity domains presented by the + “ibm,associativity” property containing + “near” and “far” resources. The first such boundary + in the list represents the 1 based ordinal in the associativity lists of the + most significant boundary, with subsequent entries indicating progressively + less significant boundaries. + Note: Platforms are encouraged to report + boundaries of actual significance. Thus if a platform has only a single + significant boundary to report, the preferred form of the + “ibm,associativ¬ity-reference-points” would + contain a single entry. However, providing two or more entries that reference + the same associativity domains provides equivalent information and is a legal + representation. +
+
+ +
+ Dynamic Reconfiguration with Cross CEC I/O Drawers + Should the configuration change in such a way that the associativity + between an OS image’s resources changes, the platform notifies the OS + via an event scan log. See . + + + + R1--1. + + For the NUMA or Associativity + Information option: If the platform configuration changes in such a + way that the associativity between an OS image’s resources might have + changed, the platform must notify the OS via an event scan or check exception + log. + + + +
+ +
+ Maximum Associativity Domains + Since the number of associativity domains that a platform may exhibit + is not apparent from the associativity properties presented at boot time, the + platform provides the “ibm,max-associativity-domains” + property in the /rtas node of the device tree (see + ). + + + + R1--1. + + For the NUMA or Associativity + Information option: The platform must provide the + “ibm,max-associativity-domains” property in + the /rtas node of the device tree. + + + +
+ +
+ Platform Resource Reassignment Notification Option (PRRN) + LoPAR platforms that implement the LPAR option are allowed to + transparently reassign the platform resources that are used by a partition. For + instance, if a processor or memory unit is predicted to fail, the platform may + transparently move the processing to an equivalent unused processor or the + memory state to an equivalent unused memory unit. However, reassigning + resources across NUMA boundaries may alter the performance of the partition. + When such reassignment is necessary, the PRRN option provides mechanisms that + inform the supporting OS of changes to the affinity among its platform + resources. It is expected that handling such notifications will involve + significant OS processing, therefore, changing affinity should be avoided, and + when it is necessary to change the affinity of several of the resources owned + by a partition, a single notification after all such changes have occurred is + preferred. + The OS and platform firmware negotiate their mutual support of the + PRRN option via the ibm,client-architecture-support + interface (See ). Should a partition be + migrated from a platform that did not support the PRRN option, the target + platform does not notify the partition’s OS of any PRRN events and, when + possible avoids changing the affinity among the partition’s resources. + Partitions that are about to be migrated complete/abort any in-process affinity + change processing prior to the migration, and if the target platform does not + support the PRRN option the partition will simply see no more PRRN + events. + A PRRN event is signaled via the RTAS event-scan + mechanism, which returns a Hot Plug Event message “fixed + part” (See ) indicating “Platform + Resource Reassignment”. In response to the Hot Plug Event message, the + OS may call ibm,update-nodes to determine which resources + were reassigned, and then ibm,update-properties to obtain + the new affinity information about those resources. + The PRRN event-scan RTAS message contains only + the “fixed part” with the “Type” field set to the + value 160 and no Extended Event Log. The four (4) byte Extended Event Log + Length field is repurposed, since no Extended Event Log message is included, to + pass the “scope” parameter that causes the + ibm,update-nodes to return the nodes affected by the specific + resource reassignment. + Requirements: + + + + R1--1. + + For the PRRN Option: + The platform must support the negotiation of the Associativity Information + Option Control Platform Resource Reassignment Notification (Affinity Change) + flag via the ibm,client-architecture-support + interface. + + + + + R1--2. + + For the PRRN Option: + If the client code did not claim support for the PRRN option via the + ibm,client-architecture-support interface the platform must not + present PRRN events per section . + + + + + R1--3. + + For the combination of the PRRN + and Partition Suspension Options: To avoid firmware function + conflicts the client code must complete or abort any PRRN processing prior to + exercising the Partition Suspension option. + + + + + R1--4. + + For the PRRN Option: + The platform must inform the client code of platform resource reassignments via + the event-scan RTAS mechanism with a “fixed + part” only event return message as presented in + + + + + R1--5. + + For the PRRN Option: + The platform must support the Platform Resource Reassignment scope (negative of + the value contained in bits 32:64 of the RTAS Event Return Format (Fixed Part) + for PRRN events) input parameter to input the + ibm,update-nodes RTAS call. + + + + + + RTAS Event Return Format (Fixed Part) for PRRN events + + + + + + + + + Bit Field Name (bitnumber(s)) + + + + + Description, Values (Described in ) + + + + + + + + Version (0:7) + + + A distinct value used to identify the architectural version of message + + + + + Severity (8:10) + + + EVENT (1) + + + + + RTAS Disposition (11:12) + + + FULLY_RECOVERED(0) + + + + + Optional_Part_Presence (13) + + + NOT_PRESENT (0): The optional Extended Error Log is not present. + + + + + Reserved (14:15) + + + 0b00 + + + + + Initiator (16:19) + + + HOT PLUG (6) + + + + + Target (20:23) + + + UNKNOWN (0): Not Applicable + + + + + Type (24:31) + + + Platform Resource Reassignment (160) – includes Change Scope in bits 32:63 + + + + + Extended Event Log Length / Change Scope (32:63) + + + The scope parameter to be input the ibm,update-nodes RTAS call + to retrieve the nodes that were changed by selected “Hot Plug” + events. + + + + +
+
+ diff --git a/Platform/ch_platform_intro.xml b/Platform/ch_platform_intro.xml new file mode 100644 index 0000000..2512dc4 --- /dev/null +++ b/Platform/ch_platform_intro.xml @@ -0,0 +1,148 @@ + + + Introduction + + This architecture specification provides a comprehensive computer + system platform-to-software interface definition, combined with minimum system + requirements, that enables the development of and software porting to a range + of compatible industry-standard computer systems from workstations through + servers. These systems are based on the requirements defined in + The + term “Processor Architecture” (PA) is used throughout this + document to mean compliance with the requirements specified in + .. The definition supports + the development of both uniprocessor and multiprocessor system + implementations. + A key attribute and benefit of this architecture is the ability of + platform developers to have degrees of freedom of implementation below the + level of architected interfaces and therefore have the opportunity for adding + unique value. This flexibility is achieved through architecture facilities + including: (1) device drivers; (2) Open Firmware (OF); (3) + Run-Time Abstraction Services (RTAS); + and (4) hardware abstraction layers. The role of items 1 + and 4 are described in separate operating system (OS) documentation. The role + that items 2 and 3 play in this architecture will be described in subsequent + paragraphs and chapters. + This architecture combines leading-edge technologies to create a + superior computing platform. By design, it supports a wide range of computing + needs including personal productivity, engineering design, data management, + information analysis, education, desktop publishing, multimedia, entertainment, + and database, file, and application servers. This architecture effectively + leverages industry-standard I/O through the PCI bus. Systems based on this + architecture are expected to offer price/performance advantages and to address + the expected growth in computing performance and functionality. + Architecture Note: In modern platforms, designers may choose + between various PCI topology standards. This architecture uses the term + “PCI” as a general term to describe the most recent versions of + all forms of PCI standards including any approved Engineering Change Requests + (ECRs) against them. In cases where there are significant differences between + individual PCI standards, the following terminology is used to differentiate + between the PCI standards. + + + + The term “conventional PCI” refers to behavior or + features that conform to the most recent version of the + , including any approved ECRs against it. + + + + + The term “PCI-X” refers to behavior or features that + conform to the most recent version of the + , including any approved ECRs against it. + + + + The term “PCI Express” refers to behavior or features + that conform to the most recent version of the + including any approved ECRs against it. In + addition, the terms “bus,” “bridge” and “PCI + Host Bridge (PHB)” used in relation to “PCI” throughout + this architecture may refer to a PCI Express “link,” + “switch,” and “root complex” respectively. + + + +
+ Platform Topology + To the experienced computer designer and system manufacturer, much of + the content of this architecture will be familiar. A typical desktop topology + is shown in . This topology consists + of a single PA processor, volatile System Memory, and a single Host Bridge + providing a PCI Bus. The PCI Bus provides for connection of I/O adapters + (IOAs). See for the definition of an + IOA. + A more complex general topology is shown in + . All platforms consist of one or more PA + processors, a volatile System Memory separate from other subsystems, and a + number of IOAs, which may initiate transactions to System Memory. The + processors are linked over the primary processor bus/switch to each other, to + the System Memory, and to one or more Host Bridges. In general, IOAs do not + connect to the primary processor bus/switch. The Host Bridges connect to + secondary buses which have IOAs connected to them. In turn, one or more bus + bridges may be employed to tertiary buses (and beyond) with additional IOAs + connected to them. Typically, the bus speeds and throughput decrease and the + number of supportable loads increases as one progresses from the primary + processor bus to more remote buses. + There are variations on these topologies, which are likely to occur + and are therefore worth describing below. This architecture describes + interfaces, not implementation. The logical software model must remain the + same, even if the physical topology is different. + + + + In a smaller platform, the Host Bridge and/or the memory and/or an + IOA may be integrated into a single chip. In this case, the topology would not + look like from a chip point of view, + but instead would be integrated onto the single chip. + + + + In a larger platform, secondary buses may be implemented, with two + or more Host Bridges, as two or more parallel expansion buses for performance + reasons. Similarly, tertiary buses may be two or more parallel expansion buses + off each secondary bus. This is indicated by the ellipses near the Host Bridge + and the Bus Bridge. + + + + In a high performance platform, with multiple processors and + multiple memoriea switch may be employed to allow multiple parallel accesses + by the processors to memory. The path through the switches would be decided by + the addressing of ths, a switch may be employed to allow multiple parallel accesses + by the processors to memory. The path through the switches would be decided by + the addressing of the memory. + + + Each of the following chapters provides information necessary to + successfully implement compliant systems. It is recommended that the reader + become thoroughly familiar with the contents of these chapters and their + references prior to beginning system or software development. It is anticipated + that standard chip sets will simplify the development of compliant + implementations consistent with the topologies shown below and will be + available from third-party industry sources. +
+ Typical Desktop Topology + + + + +
+
+ General Platform Topology + + + + +
+ Note: To enable the implementation of a large number of I/O adapters in a large + system, the Host Bridge may be split into two pieces -- a Hub and a Bridge -- + with the two connected by a cable, thus enabling the I/O adapters to be housed + at a distance from the main processor enclosure. +
+ diff --git a/Platform/ch_processors_memory.xml b/Platform/ch_processors_memory.xml new file mode 100644 index 0000000..ff7d24b --- /dev/null +++ b/Platform/ch_processors_memory.xml @@ -0,0 +1,813 @@ + + + Processor and Memory + + The purpose of this chapter is to specify the processor and memory + requirements of this architecture. The processor architecture section addresses + differences between the processors in the PA family as well as their interface + variations and features of note. The memory architecture section addresses + coherency, minimum system memory requirements, memory controller requirements, + and cache requirements. + +
+ Processor Architecture + The Processor Architecture (PA) governs software compatibility at an + instruction set and environment level. However, each processor implementation + has unique characteristics which are described in its user’s manual. To + facilitate shrink-wrapped software, this architecture places some limitations + on the variability in processor implementations. Nonetheless, evolution of the + PA and implementations creates a need for both software and hardware developers + to stay current with its progress. The following material highlights areas + deserving special attention and provides pointers to the latest + information. + +
+ Processor Architecture Compliance + The PA is defined in . + + + + R1--1. + + Platforms must incorporate only processors which comply fully + with . + + + + + R1--2. + + For the Symmetric Multiprocessor option: + Multiprocessing platforms must use only processors which + implement the processor identification register. + + + + + R1--3. + + Platforms must incorporate only processors which implement + tlbie and tlbsync, and + slbie and slbia for + 64-bit implementations. + + + + + R1--4. + + Except where specifically noted otherwise + in , platforms must support all + functions specified by the PA. + + + + Hardware and Software Implementation Note: The PA and this + architecture view tlbia + as an optional performance enhancement. Processors need not + implement tlbia. Software that needs to purge the TLB should provide a sequence + of instructions that is functionally equivalent to tlbia and use the content of + the OF device tree to choose the software implementation or the hardware + instruction. See for details. +
+ +
+ PA Processor Differences + A complete understanding of processor differences may be obtained + by studying and the user’s + manuals for the various processors. + The creators of this architecture cooperate with processor + designers to maintain a list of supported differences, to be used by the OS + instead of the processor + version number (PVN), + enabling execution on future processors. OF communicates these differences via properties of the + cpu node of the OF device tree. Examples of OF device + tree properties which support these differences include “64-bit” + and “performance-monitor”. See + for a complete listing and more details. + + + + R1--1. + + The OS must use the properties of the cpu + node of the OF device tree to determine the programming model of the processor + implementation. + + + + + R1--2. + + The OS must provide an execution path + which uses the properties of the cpu node of the OF + device. The PVN + is available to the platform aware OS for exceptional cases such as performance + optimization and errata handling. + + + + + R1--3. + + The OS must + support the 64-bit page table formats defined by + . + + + + + R1--4. + + Processors which exhibit the + “64-bit” property of the + cpu node of the OF device tree must also implement the + “bridge architecture,” an option in . + + + + + + R1--5. + + Platforms must restrict their choice of processors to those whose + programming models may be described by the properties defined for the + cpu node of the OF device tree in + . + + + + + R1--6. + + Platform firmware must initialize the + second and third pages above Base correctly for the + processor in the platform prior to giving control to the OS. + + + + + R1--7. + + OS and application software must not + alter the state of the second and third pages above Base. + + + + + R1--8. + + Platforms must implement the + “ibm,platform-hardware-notification” property (see + ) and include all PVRs that the platform may + contain. + + + + +
+ 64-bit Implementations + + Some 64-bit processor implementations will not support the full + virtual address allowed by . As a + result, this architecture adds a 64-bit virtual address subset to the PA and + the corresponding cpu node property + “64-bit-virtual-address” to OF. + In order for an OS to make use of the increased addressability of + 64-bit processor implementations: + + + + The memory subsystem must support the addressing of memory + located at or beyond 4 GB, and + + + + Any system memory located at or beyond 4 GB must be reported via + the OF device tree. + + + + At an abstract level, the effort to support 64-bit architecture in + platforms is modest. The requirements follow. + + + + R1--1. + + The OS must support the 64-bit virtual + address subset, but may defer support of the full 80-bit virtual address until + such time as it is required. + + + + + R1--2. + + Firmware must report the + “64-bit-virtual-address” + property for processors which implement the 64-bit virtual address subset. + + + + + R1--3. + + RTAS must be capable of being + instantiated in either a 32-bit or 64-bit mode on a platform with addressable + memory above 4 GB. + + + + + Software Implementation Note: A 64-bit OS need not require 64-bit + client interface services in order to boot. Because of the problems that might + be introduced by dynamically switching between 32-bit and 64-bit modes in OF, + the configuration variable 64-bit-mode? is provided so + that OF can statically configure itself to the needs of the OS. +
+
+ +
+ Processor Interface Variations + Individual processor interface implementations are described in + their respective user’s manuals. +
+ +
+ PA Features Deserving Comment + Some PA features are optional, and need not be implemented in a + platform. Usage of others may be discouraged due to their potential for poor + performance. The following sections elaborate on the disposition of these + features in regard to compliance with the PA. + +
+ Multiple Scalar Operations + The PA supports multiple scalar operations. The multiple scalar + operations are Load and Store String and Load and Store Multiple. + Due to the long-term performance disadvantage associated with multiple scalar + operations, their use by software is not recommended. +
+ +
+ External Control Instructions (Optional) + The external control instructions + (eciwx and ecowx) are not supported + by this architecture. +
+
+ +
+ <emphasis role="bold"><literal>cpu</literal></emphasis> Node <emphasis role="bold"><literal>“Status”</literal></emphasis> Property + See for the values of the + “status” property of the cpu + node. +
+ +
+ Multi-Threading Processor Option + Power processors may optionally support multi-threading. + + + + R1--1. + + For the Multi-threading + Processor option: The platform must supply one entry in the + ibm,ppc-interrupt-server#s property associated with the + processor for each thread that the processor supports. + + + + Refer to for the definition of + the ibm,ppc-interrupt-server#s property. +
+
+ +
+ Memory Architecture + The Memory Architecture of an LoPAR implementation is defined by + and + , which defines what platform elements + are accessed by each real (physical) system address, as well as the sections + which follow. + The PA allows implementations to incorporate such performance + enhancing features as write-back caching, non-coherent instruction caches, + pipelining, and out-of-order and speculative execution. These features + introduce the concepts of coherency (the apparent order + of storage operations to a single memory location as observed by other + processors and DMA) and consistency (the order of storage + accesses among multiple locations). In most cases, these features are + transparent to software. However, in certain circumstances, OS software + explicitly manages the order and buffering of storage operations. By + selectively eliminating ordering options, either via storage access mode bits + or the introduction of storage barrier instructions, software can force + increasingly restrictive ordering semantics upon its storage operations. Refer + to for further details. + PA processor designs usually allow, under certain conditions, for + caching, buffering, combining, and reordering in the platform’s memory + and I/O subsystems. The platform’s memory subsystem, system + interconnect, and processors, which cooperate through a platform implementation + specific protocol to meet the PA specified memory coherence, consistency, and + caching rules, are said to be within the platform’s coherency + domain. + shows an example system. + The shaded portion is the PA coherency domain. Buses 1 through 3 lie outside + this domain. The figure shows two + I/O subsystems, each interfacing with the host system via a Host Bridge. Notice that + the domain includes portions of the Host Bridges. This symbolizes the role of + the bridge to apply PA semantics to reference streams as they enter or leave + the coherency domain, while implementing the ordering rules of the I/O bus + architecture. + Memory, other than System Memory, is not required to be coherent. + Such memory may include memory in IOAs. + +
+ Example System Diagram Showing the PA Coherency Domain + + + + + + + + +
+ + Hardware Implementation Note: Components of the platform within the + coherency domain (memory controllers and in-line caches, for example) + collectively implement the PA memory model, including the ordering of + operations. Special care should be given to configurations for which multiple + paths exist between a component that accesses memory and the memory itself, if + accesses for which ordering is required are permitted to use different paths. + +
+ System Memory + System Memory normally consists of dynamic read/write random access + memory which is used for the temporary storage of programs and data being + operated on by the processor(s). A platform usually provides for the expansion + of System Memory via plug-in memory modules and/or memory boards. + + + + R1--1. + + Platforms must provide at least 128 MB of + System Memory. (Also see for + other requirements which apply to memory within the first 32MB of System + Memory.) + + + + + R1--2. + + Platforms must support the expansion of + System Memory to 2 GB or more. + + + + + Hardware Implementation Note: These requirements are minimum + requirements. Each OS has its own recommended configuration which may be + greater. + + Software Implementation Note: System Memory will be described by + the properties of the memory node(s) of the OF + device tree. +
+ +
+ Memory Mapped I/O (MMIO) and DMA Operations + Storage operations which cross the coherency domain boundary are + referred to as Memory Mapped I/O (MMIO) operations if they are initiated within + the coherency domain, and DMA operations + if they are initiated outside the coherency domain + and target storage within it. Accesses with targets outside the coherency + domain are assumed to be made to IOAs. These accesses are considered performed + (or complete) when they complete at the IOA’s I/O bus interface. + Bus bridges translate between bus operations on the initiator and + target buses. In some cases, there may not be a one-to-one correspondence + between initiator and target bus transactions. In these cases, the bridge + selects one or a sequence of transactions which most closely matches the + meaning of the transaction on the source bus. See also + for more details and the appropriate PCI + specifications. + For MMIO Load and Store + instructions, the software needs to set up the WIMG bits + appropriately to control Load and Store caching, + Store combining, and + speculative Load execution to I/O addresses. This + architecture does not require platform support of caching of MMIO + Load and Store instructions. + See the PA for more information. + + + + R1--1. + + For MMIO Load and Store instructions, + the hardware outside of the processor must not + introduce any reordering of the MMIO instructions for a processor or processor + thread which would not be allowed by the PA for the instruction stream executed + by the processor or processor thread. + Hardware Implementation Note: Requirement + may imply that hardware outside of + the processor cannot reorder MMIO instructions from the same processor or + processor thread, but this depends on the processor implementation. For + example, some processor implementations will not allow multiple + Loads to be issued when those Loads are to + Cache Inhibited and Guarded space (as are MMIO Loads ) or + allow multiple Stores to be issued when those + Stores are to Cache Inhibited and Guarded space (as are MMIO + Stores). In this example, hardware external to the + processors could re-order Load instructions with respect + to other Load instructions or re-order + Store instructions with respect to other Store + instructions since they would not be from the same processor or thread. + However, hardware outside of the processor must still take care not to re-order + Loads with respect to Stores or + vice versa, unless the hardware has access to the entire instruction stream to + see explicit ordering instructions, like eieio. Hardware outside of the + processor includes, but is not limited to, buses, interconnects, bridges, and + switches, and includes hardware inside and outside of the coherency + domain. + + + + + R1--2. + + (Requirement Number Reserved + For Compatibility) + + + + + Apart from the ordering disciplines stated in Requirements + and, for PCI the ordering of MMIO + Load data return versus buffered DMA data, as defined by + Requirement , no other ordering + discipline is guaranteed by the system hardware for Load + and Store instructions performed by a processor to + locations outside the PA coherency domain. Any other ordering discipline, if + necessary, must be enforced by software via programming means. + The elements of a system outside its coherency domain are not + expected to issue explicit PA ordering operations. System hardware must + therefore take appropriate action to impose ordering disciplines on storage + accesses entering the coherency domain. In general, a strong-ordering rule is + enforced on an IOA’s accesses to the same location, and write operations + from the same source are completed in a sequentially consistent manner. The + exception to this rule is for the special protocol ordering modifiers that may + exist in certain I/O bus protocols. An example of such a protocol ordering + modifier is the PCI Relaxed Ordering bitThe PCI + Relaxed Ordering bit is an optional + implementation, from both the IOA and platform perspective. , + as indicated in the requirements, below. + + + + R1--3. + + Platforms must guarantee that accesses + entering the PA coherency domain that are from the same IOA and to the same + location are completed in a sequentially consistent manner, except transactions + from PCI-X and PCI Express masters may be reordered when the Relaxed Ordering + bit in the transaction is set, as specified in the + and + . + + + + + R1--4. + + Platforms must guarantee that multiple write operations entering + the PA coherency domain that are issued by the same IOA are completed in a + sequentially consistent manner, except transactions from PCI-X and PCI Express + masters may be reordered when the Relaxed Ordering bit in the transaction is + set, as specified in the + and + . + + + + + R1--5. + + Platforms must be designed to present I/O DMA writes to the coherency domain in the order required by + , except transactions from PCI-X and PCI + Express masters may be reordered when the Relaxed Ordering bit in the + transaction is set, as specified in the + and + . + + + +
+ +
+ Storage Ordering and I/O Interrupts + The conclusion of I/O operations is often communicated to + processors via interrupts. For example, at the end of a DMA operation that + deposits data in the System Memory, the IOA performing the operation might send + an interrupt to the processor. Arrival of the interrupt, however, may be no + guarantee that all the data has actually been deposited; some might be on its + way. The receiving program must not attempt to read the data from the memory + before ensuring that all the data has indeed been deposited. There may be + system and I/O subsystem specific method for guaranteeing this. See . +
+ +
+ Atomic Update Model + An update of a memory location by a processor, involving a + Load followed by a Store, can be + considered “atomic” if there are no intervening + Stores to that location from another processor or mechanism. The PA + provides primitives in the form of Load + And Reserve and Store + Conditional instructions which can be used to determine if the update was + indeed atomic. These primitives can be used to emulate operations such as + “atomic read-modify-write” and “atomic + fetch-and-add.” Operation of the atomic update primitives is based on + the concept of “Reservation,”See + Book I and II of . + which is supported in an LoPAR system via the coherence mechanism. + + + + R1--1. + + Load And Reserve and + Store Conditional instructions + must not be assumed to be supported for Write-Through storage. + Software Implementation Note: To emulate an + atomic read-modify-write operation, the instruction pair must access the same + storage location, and the location must have the Memory Coherence Required + attribute. + Hardware Implementation Note: The reservation + protocol is defined in Book II of the + for atomic updates to locations in the same coherency domain. + + + + + R1--2. + + The Load And + Reserve and Store Conditional instructions + must not be assumed to be supported for Caching-Inhibited storage. + + + +
+ +
+ Memory Controllers + A Memory Controller responds to the real (physical) addresses + produced by a processor or a host bridge for accesses to System Memory. It is + responsible for handling the translation from these addresses to the physical + memory modules within its configured domain of control. + + + + R1--1. + + Memory controller(s) must support the + accessing of System Memory as defined in . + + + + + R1--2. + + Memory controller(s) must be fully initialized and + set to full power mode prior to the transfer of control to the OS. + + + + + R1--3. + + All allocations of System Memory space + among memory controllers must have been done prior to the transfer of control + to the OS. + + + + Software Implementation Note: Memory controller(s) are described by + properties of the memory-controller node(s) of the OF device + tree. +
+ +
+ Cache Memory + + All of the PA processors include some amount of on-chip or + internal cache memory. + This architecture allows for cache memory which is external to the processor + chip, and this external + cache memory forms an extension to internal cache memory. + + + + R1--1. + + If a platform implementation elects not + to cache portions of the address map in all external levels of the cache + hierarchy, the result of not doing so must be transparent to the operation of + the software, other than as a difference in performance. + + + + + R1--2. + + All caches must be fully + initialized and enabled, and they must have + accurate state bits prior to the transfer of control to the OS. + + + + + R1--3. + + If an in-line external + cache is used, it must support one reservation as + defined for the Load And Reserve and + Store Conditional instructions. + + + + + R1--4. + + For the Symmetric + Multiprocessor option: Platforms must implement their cache + hierarchy such that all caches at a given level in the cache hierarchy can be + flushed and disabled before any caches at the next level which may cache the + same data are flushed and disabled (that is, L1 first, then L2, and so + on). + + + + + R1--5. + + For the Symmetric + Multiprocessor option: If a cache implements snarfing, + then the cache must be capable of disabling the snarfing during flushing in order to implement + the RTAS stop-self function in an atomic way. + + + + + R1--6. + + Software must not depend on being able to + change a cache from copy-back to write-through. + + + + + Software Implementation Notes: + + + + Each first level cache will be defined via properties of the + cpu node(s) of the OF device tree. Each higher level cache will be + defined via properties of the l2-cache node(s) + of the OF device tree. See for more details. + + + + To ensure proper operation, cache(s) at the same level in the + cache hierarchy should be flushed and disabled before cache(s) at the next + level (that is, L1 first, then L2, and so on). + + + +
+ +
+ Memory Status information + New OF properties are defined to support the identification and + contain the status information on good and bad system memory. + + + + R1--1. + + Firmware must implement all of the + properties for memory modules, as specified by , + and any other properties defined by this document which apply to memory modules. + + + +
+ +
+ Reserved Memory + Sections of System Memory may be reserved for usage by OS + extensions, with the restrictions detailed below. Memory nodes marked with the + special value of the “status” property of + “reserved” is not to be used or altered by the base OS. Several + different ranges of memory may be marked as “reserved”. If DLPAR + of memory is to be supported and growth is expected, then, an address range + must be unused between these areas in order to allow growth of these areas. + Each area has its own DRC Type (starting at 0, MEM, MEM-1, MEM-2, and so on). + Each area has a current and a maximum size, with the current size being the sum + of the sizes of the populated DRCs for the area and the max being the sum total + of the sizes of all the DRCs for that area. The logical address space allocated + is the size of the sum of the all the areas' maximum sizes. Starting with + logical real address 0, the address areas are allocated in the following order: + OS, DLPAR growth space for OS (if DLPAR is supported), reserved area (if any) + followed by the DLPAR growth space for that reserved area (if DLPAR is + supported), followed by the next reserved space (if any), and so on. The + current memory allocation for each area is allocated contiguously from the + beginning of the area. On a boot or reboot, including hypervisor reboot, if + there is any data to be preserved (that is, the + “ibm,preserved-storage” + property exists in the RTAS + node), then the starting logical real address of each LMB is maintained through + the reboot. The memory in each region can be independently increased or + decreased using DLPAR memory functions, when DLPAR is supported. Changes to the + current memory allocation for an area results in the addition or removal of + memory to the end of the existing memory allocation. + Implementation Note: if the shared memory + regions are not accessed by the programs, and are just used for DMA most of the + time, then the same HPFT hit rate could be achieved with a far lower ration of + HPFT entries to logical storage space. + + + + R1--1. + + For the Reserved Memory option: + Memory nodes marked with the special value of the “status” + property of “reserved” must not be used or altered by the base OS + Implementation Note: How areas get chosen to + be marked as reserved is beyond the scope of this architecture. + + + + + R1--2. + + For the Reserved Memory option + with the LRDR option: Each unique memory area that is to be changed + independently via DLPAR must have different DRC Types (for example, MEM, MEM-1, + and so on). + + + +
+ +
+ Persistent Memory + Selected regions of storage (LMBs) may be optionally preserved + across client program boot cycles. See and + "Managing Storage Preservations" in specification. +
+
+ + diff --git a/Platform/ch_product_topology.xml b/Platform/ch_product_topology.xml new file mode 100644 index 0000000..3c734c6 --- /dev/null +++ b/Platform/ch_product_topology.xml @@ -0,0 +1,4638 @@ + + + Product Topology + +
+ VPD and Location Code OF Properties + A set of OF properties is defined to facilitate asset protection and + RAS capabilities in LoPAR systems. The following properties are defined in +): + + + + “ibm,vpd” + + + + “ibm,loc-code” + + + + + + R1--1. + + Each instance of a hardware entity (FRU) has a platform unique + location code and any node in the OF device tree that describes a part of a + hardware entity must include the + “ibm,loc-code” property with a value that represents + the location code for that hardware entity. + + + + + R1--2. + + OF nodes that do not represent an instance + of a hardware entity (FRU) do not have a location code and thus these nodes, + except for the OF root node, do not include the “ibm,loc-code” property. + Architecture Note: In general, an OF node that has a unit address + corresponds to an instance of a hardware entity and a node that does not have a + unit address does not correspond to an instance of a hardware entity. The nodes + for caches are one exception to this statement. Note that the OF + openprom node is a system node and thus should have neither the + “ibm,loc-code” property nor the + “ibm,vpd” property. + + + + + R1--3. + + If a hardware entity contains unique VPD information and the + entity corresponds to a node in the OF device tree, then that device tree node + must include the “ibm,vpd” property. + + + + + R1--4. + + An instance of a hardware entity (FRU) must + have one and only one “ibm,vpd” property + element that defines the VPD keywords specified in Requirement + . + Platform Implementation Note: In general, an + instance of a hardware entity has a single “ibm,vpd” + property element that is in one of the nodes that also contains an + “ibm,loc-code” property element for that + entity. + + + + + R1--5. + + An OF device tree node that includes the + “ibm,vpd” property must also include an + “ibm,loc-code” property, where each + property has the same number of elements and the matching elements of both + properties define the same instance of a hardware entity (FRU), where matching + elements are defined as the nth string of the “ibm,loc-code” + property and the nth set of tags in + the “ibm,vpd” property for all values of + n. + + + + + R1--6. + + VPD data that is not associated with an instance of a hardware + entity (FRU) that is described by a single OF device tree node must be reported + in an appropriate OF node using the “ibm,loc-code” and + “ibm,vpd” properties. + + + + Architecture Notes: + + + + The root node is the appropriate OF node (for Requirement ) for any instance of a hardware entity that + cannot be dynamically reconfigured. Any one and only one of the OF nodes that + describe the dynamically reconfigurable entity can contain the properties for + the dynamically reconfigurable entity case. + + + + A dynamically reconfigurable entity may consist of more than one + FRU. In this case, the first element of both the “ibm,vpd” + property and the “ibm,loc-code” property for the dynamically + reconfigurable entity must define the VPD and location code for the OF device + tree node that includes those properties. + + + + A FRU can be considered dynamically reconfigurable if the hardware + is enabled for dynamic reconfiguration and full platform support might be + implemented at a later date. + + + + Platform Implementation Note: If a location + does not return VPD, the property would contain a null entry for the VPD. +
+ +
+ System Identification + provides properties in the + “OF Root Node” section called “system-id” + and“model”. + + + + R1--1. + + (Requirement Number Reserved For Compatibility) + + + + + R1--2. + + Each system enclosure (generally, a drawer), + must have the VPD SE and TM keywords (see ). + + + + + R1--3. + + The SE and TM keywords for a + master enclosure must be contained in the “ibm,vpd” + property for the master enclosure which may + also contain other keywords. A master enclosure must also have the YK keyword + if another enclosure shares the same combined SE and TM keyword values. The YK + keyword (see ) for a secondary + enclosure must be contained in the “ibm,vpd” + property for the secondary enclosure, which may also contain other + keywords. Each master enclosure with a YK keyword must have a unique YK value + that is the same as the value of the YK keyword for each of the secondary + enclosures that share the same combined SE and TM keyword values. An enclosure + is not a FRU and thus its VPD must not contain the FN, PN, SN, EC, RM or RL + keywords. + + + + + R1--4. + + The enclosure must also be + represented in the corresponding element of the “ibm,loc-code” + property with the location code of the + enclosure for a multi-enclosure platform. + Implementation Note: The location code will be + for the full enclosure. The drawer position is the u-units counting from the + bottom of the rack. Specific numbering is platform dependent. + + + + + R1--5. + + If the system contains multiple processor enclosures, firmware + must use the VPD SE field from the first or ‘marked’ processor + enclosure (see ) to + construct “system-id”. + Implementation Note: What is meant by ‘marked’ above is + that, in a system, the ‘first’ processor enclosure could become + ambiguous. In such a case, a specific processor enclosure could be marked by + the firmware or HMC as being the processor enclosure to use for identification + purposes. + + + + + R1--6. + + One or more of the MI, RM, and RL keywords + must be present for any firmware specific VPD. (with a value of + “UNKNOWN” for unknown values), and must be present based on all + of the following: + + + + The RL keyword must be provided if the platform does not support + the ibm,update-flash-64-and-reboot RTAS call. + + + + The RM keyword must be provided if the platform supports only a + single flash image updated via the ibm,update-flash-64-and-reboot + service and does not support the ibm,manage-flash-image and + ibm,validate-flash-image RTAS calls. + + + + The MI keyword must be provided if the platform supports dual + flash images via the ibm,update-flash-64-and-reboot, the + ibm,manage-flash-image, and the ibm,validate-flash-image + RTAS calls. + + + + The ML keyword must be provided if the platform supports dual + flash images via the ibm,update-flash64-and-reboot, + the ibm,manage-flash-image, and the ibm,validate-flash-image + RTAS calls. + + + + + + + R1--7. + + System firmware and service processor + firmware must have VPD that is separate from the VPD of the FRU that contains + the system firmware and service processor firmware and this VPD must have a + location code that is made by adding “/Yn” to the end of the + location code for the FRU that contains the firmware where n is a platform + dependent instance of the firmware. + + + + + R1--8. + + The description (large resource type of + 0x82) for the system firmware VPD in the “ibm,vpd” + property must be “System Firmware or + Platform Firmware”. + + + + + R1--9. + + System firmware VPD must be found in the + root node if the system supports only static VPD, + otherwise system firmware VPD must be provided via the + ibm,get-vpd RTAS call. + + + + + R1--10. + + The description (large resource type of + 0x82) for the service processor firmware VPD in the “ibm,vpd” + property must be “Service Processor + Firmware”, if the service processor firmware is a separate FRU from the + system firmware. + + + + + R1--11. + + Service processor firmware VPD must be + found in the root node if the service processor firmware is a separate FRU from + the system firmware. + + + + + R1--12. + + The VPD SE field (see ) + must be electronically stored in a manner that is not modifiable in a user + environment. + + + + + R1--13. + + There must be a property, “model”, + under the root node in the format, + “<vendor>,xxxx-yyy”, where <vendor> is replaced by + one to five letters representing the stock symbol of the company (for example, + for IBM: “IBM,xxxx-yyy”), and where xxxx-yyy is derived from the + VPD TM field (see ) of the first or + ‘marked’ processor enclosure. + + + + + R1--14. + + The values of the type/model (TM) and system serial number (SE) + (see ) must remain the same even with + service or reconfiguration of the system. + Implementation Note: A change in either TM or + SE would indicate a system replacement as opposed to a reconfiguration. + + + + + This definition of the“system-id” + property provides extensibility and ensures that uniqueness can be + maintained. The 2 byte Field Type will serve to identify the format of the + System Identifier Field which follows. + Hardware Implementation Note: It is recommended that the VPD SE field + be held in an area of the machine that is least susceptible to hardware + failure. This is to minimize the effect on software licensing when a FRU must + be changed. Another useful technique is to socket the part containing the SE + field, allowing service personnel to move the old SE to the new FRU. +
+ +
+ Hardware Location Codes + Hardware location codes are used to provide a mapping of logical + functions in a platform (or expansion sites for logical functions, such as + connectors or ports) to their specific locations within the physical structure + of the platform. The description in the following section is intended to define + a standard architecture for these location codes, which would be used in three + places: + + + + These location codes would be included as a property, + “ibm,loc-code”, under device nodes in + the OF device tree, to provide identification of where those device functions + are physically located in the platform. + + + + To make service and parts replacement easier, hardware location + codes of failing components would be appended to the standard 40-byte Extended + Error Log templates returned by the RTAS event-scan and + check-exception services. + + + + Software Note: Since the OF device tree currently only defines the + core platform devices and IOAs, OS applications such as diagnostics may need to + extend these location codes with logical addresses to point to devices such as + SCSI (Small Computer System Interface) drives or asynchronous tty + (teletypewriter) terminals. + Location Codes are globally unique within a system and are persistent + between system reboots and power cycles. + + + + R1--1. + + All platforms must implement the + Converged Location Codes option. + + + + + R1--2. + + Location codes must be globally unique + within a system, including across multiple CECs of a clustered system, and must + be persistent across multiple system reboots and power cycles. + + + + + Converged location codesThe + term “converged” is historic, based on merging (converging) + several previous versions of location codes. are strings + composed of one or more location labels separated by dashes + (“-”). Location labels are strings that begin with a location + prefix followed by a distinguishing value. For example, the location code for a + PCI (Peripheral Component Interconnect) card in a CEC (Central Electronic + Complex) might be something like this: + + + + U7879.001.1012345-P2-C3 + + + + Valid location codes consist of uppercase characters ('A' - 'Z'), + digits (0 - 9), periods ('.'), and dashes ('-'). Characters other than these + valid characters will be replaced by pound signs ('#') to protect display and + formatting routines and give a consistent indication of a problem in the data. + Periods may be used to improve readability of the location code. + The existence of the + “ibm,converged-loc-codes” property in the + root node of the device tree indicates that the platform implements + the Converged Location Codes option. + + + + + R1--3. + + For the Converged Location Codes + option: The platform must implement the “ibm,converged-loc-codes” + property in the root node of the device tree. + + + + + R1--4. + + For the Converged Location Codes + option: The location code contained in each instance of the + property “ibm,loc-code” must match the + format as described in the sections under and + . + + + + + R1--5. + + For the Converged Location Codes + option: Extended error logs reported to the OS by event-scan + orcheck-exception must have the + characters “IBM<NULL>” in bytes 12-15, and include the + location codes for the failing elements in the format as described in the + sections under and + . + + + + +
+ Converged Location Code Labels + This section describes the types of location code labels. See also + for the rules for building a location + code. + +
+ Prefix Summary Table + The prefix of a converged location code is as defined in this + section. + + + + R1--1. + + For the Converged Location + Codes option: The location code prefixes specified in + must be used in constructing location + codes. + + + + + + Converged Location Code Prefix Values + + + + + + + + Prefix + + + + + Meaning + + + + + + + + A + + + Air handler (for example: blower, fan, motor scroll + assembly, motor drive assembly). . + + + + + C + + + Card Connector (for example, connector for: IOA, + Processor Card, Riser Card, Daughter Card, DIMM, Regulator Card, MCM, L3 Cache, + Jumper Card, Passthru Interposer (for Processor Fabric when an MCM is not + installed), Pluggable Module Chips). + . + + + + + D + + + Device (for example: Diskette, DASD, Operator Panel, SES + (Storage Enclosure Services) Device). + . + + + + + E + + + Electrical (for example: Battery, Power Supply, + Charger). . + + + + + F + + + Frame. See + . + + + + + L + + + Logical Path (for example: SCSI Target, IDE Address, + ATAPI Address, Fibre Channel LUN, etc.). + . + + + + + M + + + Mechanical (Plumbing, Valves, Latches). See + . + + + + + N + + + Horizontal placement for an empty rack location. See + . + + + + + P + + + Planar (for example: Backplane, Board). + . + + + + + R + + + Resource (identifies a resource that is not a FRU, but + needs identification in the error log). See + . + + + + + S + + + SR-IOV adapter virtual function. See + . + + + + + T + + + Port (for example: Port, Connector, Cable Connector, + Jack, Interposer). + . + + + + + U + + + Unit (for example: System, CEC, Card Cage, Drawer, + Chassis (Unpopulated drawer)). + . + + + + + V + + + Virtual Planar. See . + + + + + W + + + Worldwide unique ID (for example: Fibre Channel). + . + + + + + X + + + EIA value for empty rack location. See + . + + + + + Y + + + Firmware FRU. See . + + + + +
+
+ +
+ Unit Location Label + The unit location label consists of the prefix “U” + followed by uppercase alphabetic characters, digits, and periods + (“.”). There is one and only one unit location label in a + location code and it is the first element in the location code. +
+ +
+ Planar Location Label + The planar location label consists of the prefix “P” + followed by a non-zero decimal number with no leading zeroes. Planar location + labels are present in location codes for planars and all locations on a planar. + There is at most one planar location label in a location code. When present, + the planar location label immediately follows the unit location label in the + location code. + Planars are uniquely labeled within a unit. +
+ +
+ Air Handler Location Label + An air handler location label consists of the prefix + “A” followed by a non-zero decimal number with no leading zeroes. + A location code may have zero or more air handler location labels. When + present, the air handler location label follows the location label of the + resource onto which the air handler is mounted, usually a unit or planar. + Examples of air handlers include blowers and fans. +
+ +
+ Card Connector Location Label + The card connector location label consists of the prefix + “C” followed by a non-zero decimal number with no leading zeroes. + A location code may contain zero or more card connector location labels. When + present, the card connector location label follows the location label of the + resource onto which the card is mounted, usually a planar or another + card. + Examples of cards include: Plug-in I/O cards, processor cards, + daughter cards, DIMMs, regulator cards, MCMs, L3 cache modules, jumper cards, + pass-through interposers, and pluggable module chips. +
+ +
+ Device Location Label + A device location label consists of the prefix “D” + followed by a non-zero decimal number with no leading zeroes. A location code + may have zero or more device location labels. When present, the device location + label follows the location label of the resource onto which the device is + mounted, usually a planar. + Device location labels are used for devices for which a physical + location can be determined. These are usually mounted in enclosures that have + rigid placement rules and, often, additional hardware support for location + determination, such as SES (Storage Enclosure Services) devices. +
+ +
+ Electrical Location Label + An electrical location label consists of the prefix + “E” followed by a non-zero decimal number with no leading zeroes. + A location code may have zero or more electrical location labels. When present, + the electrical location label follows the location label of the resource onto + which the electrical resource is mounted, usually a unit or planar. + Examples of electrical resources include: batteries, power + supplies, and chargers. +
+ +
+ Port Location Label + A port location label consists of the prefix “T” + followed by a non-zero decimal number with no leading zeroes. A location code + may have zero or more port location labels. When present, the port location + label follows the location label of the resource onto which the port is + mounted, usually a card or planar. + Examples of resources with a port location label include: ports, + connectors, cable connectors, jacks, and interposers. +
+ +
+ Worldwide Unique Identifier + A worldwide unique identifier location label consists of the prefix + “W” followed by a maximum of 16 uppercase hexadecimal digits with + no leading zeroes. A location code may have zero or one worldwide unique + identifier location labels. When present, the worldwide unique identifier + location label follows the location label of the resource that interfaces with + the resource having the worldwide unique identifier, usually a port. +
+ +
+ Logical Path Label + A logical path location label consists of the prefix + “L” followed by a decimal or hexadecimal number with no leading + zeros. Refer to through + to determine when decimal and hexadecimal + values are allowed. A location code may have zero or more logical path location + labels. When present, the logical path location label follows the location + label of the resource that interfaces with the resource being located, usually + a port or worldwide unique identifier. + The numeric value portion of the logical path label is a portion of + the address, appropriate to the protocol in use, which identifies the resource + to be located. +
+ +
+ Virtual Planar Location Label + A virtual planar label consists of the prefix “V” + followed by a non-zero decimal number with no leading zeroes. A location code + may have zero or one virtual planar location labels. When present, the virtual + planar location label will immediately follow the unit location label in a + location code. There is no physical label in the system or any I/O drawer + corresponding to the virtual planar location label. + Virtual planars are uniquely labeled within a system. +
+ +
+ Firmware Location Label + A firmware location label consists of the prefix “Y” + followed by a non-zero decimal number with no leading zeroes. A location code + may have zero or one firmware location labels. A firmware location code will + always contain a unit location label as its first element and a firmware + location label its last element. +
+ +
+ Horizontal Placement Location Label + The horizontal placement location label of an empty space in a rack + consists of the prefix “N” followed by a non-zero decimal number + with no leading zeroes. A location code may have zero or one horizontal + placement location labels. When present, the horizontal placement location + label immediately follows the EIA location label. +
+ +
+ EIA Location Label + The EIA location label of an empty space in a rack consists of the + prefix “X” followed by a non-zero decimal number with no leading + zeroes. A location code may have zero or one EIA location labels. When present, + the EIA location label immediately follows the frame location label. +
+ +
+ Frame Location Label + The frame location label of an empty space in a rack consists of + the prefix “F” followed by a non-zero decimal number with no + leading zeroes. A location code may have zero or more frame location labels. + When present, the frame location label immediately follows the unit location + label. +
+ +
+ Virtual Function Location Label + A virtual function label consists of the prefix “S” + followed by a zero-starting decimal number with no leading zeros. A location + code may have zero or more virtual function labels. When present, the virtual + function label is appended to the location code of the port that the virtual + function uses. +
+ +
+ Mechanical Location Label + The Mechanical location label consists of the prefix + “M” followed by a nonzero decimal number with no leading zeroes. + A location code my have zero or more Mechanical location labels. When present, + the Mechanical location label follows the location label of the resource onto + which the mechanical device is mounted. + Examples of resources with a mechanical location label include: + plumbing, valves, and latches. +
+ +
+ Resource Location Label + The Resource location label consists of the prefix + “R” followed by a nonzero decimal number with no leading zeroes. + A location code my have zero or more Resource location labels. When present, + the Resource location label follows the location label of the parent FRU. + + Resource location labels are resources, that are not FRUs, but that + need a location code label to be properly identified in the error log. An + example of a Resource is a module on the System backplane that is not a + separate FRU, but which needs to be separately identified in the system error + log for a fail in place type of service strategy. +
+
+ +
+ Converged Location Code Rules + This section describes the rules for building a location code. See + also the types of location code + labels. + +
+ Usage of Location Codes + Any reference to a FRU must reference the official location + code. + Unofficial internal forms or values of location codes which system + components may use for internal convenience are not to be presented to + customers, service personnel, etc. They are to be kept internal to those + components. +
+ +
+ Persistence of Location Codes + Physical path location codes are permanent. Physical path location + codes will not change unless there has been a change of hardware. + Logical path location codes are dependent on configuration + information and are therefore not permanent. Whenever reasonable and possible, + logical path location codes will persist across power cycles of the + system. +
+ +
+ Forming Location Codes + Location codes are formed by concatenating one or more location + labels together. Location labels start at the largest or most general resource + (the unit) and proceed to the most specific in order of containment. The + location labels are separated by dashes (“-”). +
+ +
+ Length Restrictions + Location codes are no more than 79 characters in length. The + lengths of individual location labels vary. +
+ +
+ Location Labels Content + The unit location label may contain uppercase letters, digits, and + periods. All other location labels contain only upper case letters and digits. + This will avoid problems when printing or displaying the location codes on + double byte devices. +
+ +
+ Physical Representation + In so far as it is possible, location labels must match the labels + that are present on the hardware. + Generally, there are labels visible on the hardware to identify + connectors, slots, etc. These physical labels must adhere to this specification + and must be reflected in the corresponding location codes. This will eliminate + the need for the user to translate between the location code presented in logs, + displays, reports, and instructions and the location label found on the + hardware. +
+ +
+ Multiple Function FRUs + Some FRUs (Field Replaceable Units) contain more than one logical + resource or function. The physical location code refers to the physical FRU. So + all the logical resources or functions on a FRU have the same physical location + code. Connectors on a FRU have different location codes except for the case of + multiple connectors for one port. +
+ +
+ Multiple Connectors for One Port + Some IOAs have multiple connectors (for example, a D-connector and + an RJ-45 connector) for one port. Since there is only one port involved, both + connectors have the same location code. +
+ +
+ Location Label Numbering Scope + For sequentially numbered location labels (planar, card, device, + air handler, electrical), each FRU has its own numbering space for its child + location labels. That numbering space begins with 1 and increments by 1 for + each child location label. Number is in decimal. For example, if there were two + planars in a unit, each planar having five card connectors, then each planar + would show child location labels of C1, C2, C3, C4, and C5. + This means that for each parent, the child location labels begin + with a count of one. As a further example, if there were two adapters in + adjacent PCI slots each with two port connectors, the ports on the first + adapter would have location labels T1 and T2, and the ports on the second + adapter would have location labels of T1 and T2. + Note: Model-specific modifications to this + numbering rule may be made, when similar models of a product line are housed in + the same enclosure/rack, and the equivalent slots and connectors from each + model are lined up with each other as seen by the customer. Then the location + code numbering of these equivalent slots and connectors may be the same for + each model, even though numbers may be skipped or appear to be out of order on + specific models. +
+ +
+ FRU Orientation + Locations are numbered left to right, top to bottom, back to front + with respect to the parent FRU, as viewed from the service position. However, a + location label does not change based on the orientation of a piece of hardware + within its parent hardware, for FRUs that may have more than one way of being + oriented. + If a CEC or I/O drawer is used both in standalone and rack mounted + configurations, the rack mounted configuration takes precedence in determining + location numbering. +
+ +
+ Unit Location Codes + The unit location code is the unit location label, Un, for the + unit. The unit location label is permanent. The unit location labels may not be + etched on the containing racks, since it may not be possible to determine them + during manufacture. + A system will have a unit location code composed of the machine + type, model, and serial number of the system with the components separated by + periods ('.'). For example, a system with machine type 9117, model 250, and + serial number 10-ABCDE would have a location code of: + + + + U9117.250.10ABCDE + + + + Some I/O Drawers and CECs may be assigned machine type, model, and + serial numbers (MTMS) by manufacturing. Other I/O Drawers and CECs may be + assigned feature code, count, and serial numbers by manufacturing. The same + requirements for uniqueness apply to both identification schemes. The data is + formatted in exactly the same way. And, for the purposes of location codes, the + data will be used in exactly the same way. + Drawers and CECs which have a machine type, model, and serial + number which the system can obtain will have a unit location code composed of + the machine type, model, and serial number with the components separated by + periods (“.”). For example, a drawer with machine type 5703, + model 012, and serial number 10-30490 would have a location code of: + + + + U5703.012.1030490 + + + + Drawers and CECs which have a feature code, count, and serial + number which the system can obtain will have a unit location code composed of + the feature code, count, and serial number with the components separated by + periods (‘.’), for readability. For example, a drawer with + feature code 0573, count 001, and serial number 10-40320 would have a location + code of: + + + + U0573.001.1040320 + + + + Additionally, the count portion of the location code unit label may + be modified by firmware at boot time to reflect information about the physical + location. It may be modified according to whatever scheme appropriate for the + unit's configuration -- provided all other location code rules are followed and + that the scheme generates the same value every time when no actual or relative + physical location change has been made. For example, TUn (“TU” to + indicate the Top CEC Unit, n=1,2,3, or 4 to indicate which drawer numbered top + to bottom) may be substituted for the actual count value, so an imaginary CEC + following this scheme might have a unit label of: + + U1234.TU1.5678901 + + Enclosure feature code/count must never collide with one another or + with any machine type/model. Likewise, enclosure machine type/model must never + collide with one another or any enclosure feature code/count. + Drawers for which the system cannot obtain a machine type, model, + and serial or a feature code, count, and serial number, will have a location + code of the form Uttaa. In this form, the tt is an alphabetic string + identifying the kind of drawer, for example, SSA. The aa is a string provided + by the rules of the OS to identify the instance of the drawer within the + particular system. For example: USSABKUP. The lengths of both tt and aa will + vary depending on the kind of drawer. The OS must provide mechanisms by which + the customer can ensure the uniqueness of these values. +
+ +
+ Planar Location Codes + Planar location codes are formed by appending the planar location + label, Pn, to the location code of the unit that contains the planar. The Pn + value is assigned during the engineering design and manufacturing process, is + unique within the unit, is physically displayed on the parent resource, and is + present in the VPD of the parent resource. This process is the same + irrespective of the kind of planar involved. + Note: In some implementations, a planar is + not a separate FRU but is considered to be part of the enclosure. For + consistency of the user interface, the enclosure in these cases is still + considered to have a location code consisting entirely of a unit location + label. In these cases, the planar has a location code consisting of both the + unit location label and the planar location label. This is done even though the + planar is not a separate FRU. In these cases, service related VPD and errors + will be reported with the planar location code. +
+ +
+ Card Connector Location Codes + Card connector location codes are formed by appending the card + connector location label, Cn, to the location code of the resource to which the + card is docked. The location label, Cn, assigned in the engineering and + manufacturing process, is unique within the parent resource, is physically + displayed on the parent resource, and is present in the VPD of the parent + resource. + The process is the same irrespective of the kind of card + involved. +
+ +
+ Riser Card Connector Location Codes + Riser card connector location codes are formed by appending the + card location label, Cn, of the child card to the location code of the parent + card to which it is attached. For example: + U5702.115.1031010-P3-C4-C2 +
+ +
+ Blade Daughter Card Connector Location Codes + The Blade daughter card slot can actually contain multiple + partitionable endpoints depending on the type of daughter card attached. The + PCI-E bus can be split (bifurcated) between two PHB's that are separately + DLPAR-able (just not hot-pluggable) resources. When that occurs, a -L# suffix + is required after the -C# of the daughter card slot to distinctly identify + between the two PE's. For example, when the daughter card contains two 4x PCIE + devices, the location code for the two PE's might be: + + + U78A0.001.DNWGDG0-P1-C10-L1 + + + U78A0.001.DNWGDG0-P1-C10-L2 + + + The actual daughter card device ports, in this example, will have + the -T# suffix (starting from 1) on top of those. For example, a 4-port PCI-E + Ethernet daughter card, might have location codes like: + + + U78A0.001.DNWGDG0-P1-C10-L1-T1 + + + U78A0.001.DNWGDG0-P1-C10-L1-T2 + + + U78A0.001.DNWGDG0-P1-C10-L2-T1 + + + U78A0.001.DNWGDG0-P1-C10-L2-T2 + + + If only a single PCI device is on the daughter card, then the -L# + suffix should not be used, as the -C# is sufficient to identify the PE and + device. +
+ +
+ Virtual Card Connector Location Codes + Virtual card connector location codes are formed as though there + were a virtual planar with card slots. For example, a virtual IOA would have a + location code of form: + + + U9117.150.1054321-V5-C2 + + + In the virtual card connector location code, the unit location + label specifies the system location code, not the CEC enclosure location + code. + It is recommended that the card connector location label have a + non-zero numeric part, for human factors reasons. +
+
+ Port Location Codes + Port location codes are formed by appending the port location + label, Tn, to the location code of the resource on which the port connector is + mounted. The location label, Tn, assigned in the engineering and manufacturing + process, is unique within the parent resource, is physically displayed on the + parent resource, and is present in the VPD of the parent resource. + +
+ Resources without Port VPD + If a resource without slot map VPD has port numbers physically + marked on it, the hard coded slot map will reflect the marked numbers and + letters with a “T” prefix. Any letters will be folded to + uppercase to avoid double byte display concerns. (Note: only letters 'A' - 'F' + may be used in a port location label. Other letters on the card will be ignored + and numbers will be assigned for uniqueness.) It is recognized that location + labels formed in this way may not conform to the location label rules stated in + . + If the port labels are not marked on the standalone adapter, the + hard coded slot map will specify location labels of Tn, where n is decimal and + equal to the port address (i.e. port 0 will map to T1, port 1 will map to T2, + etc.) Whenever possible, the hardware design should be such that this will lead + to the preferred left to right, top to bottom, front to back ordering. For + standalone adapters that can be installed in multiple systems, ports are + labeled beginning with the PCI connector and continuing toward the opposite + edge of the card and from tailstock forward toward the opposite edge of the + card. + If the adapter is imbedded on a FRU which does not have port + location labels marked on it and has ports for other functions, then the + numbering to the ports in the hard coded slot map must take into account the + other ports on the FRU. The hard coded slot map will comply with the left to + right, bottom to top, front to back ordering guidelines. In this case, the + first port for the imbedded adapter may be other than T0 and may not be + contiguous. +
+ +
+ Determining Port Number + If the port number cannot be determined from VPD or VPD plus + configuration or addressing information, software or firmware must infer the + port number. + + + + For SCSI IOAs with multiple PCI configuration spaces, each port + has its own configuration space. + + + + For multiport SCSI IOAs with a single PCI configuration space, + firmware or software will add n+1 to the base port's distinguishing value to + obtain the port number for the nth port. Thus port 0 (usually closest to the + PCI connector edge of the card) will have label T1, port 1 will have label T2, + etc. + + +
+ +
+ Physical Device Location Codes + Devices whose parent supports location label + VPDSES devices on SCSI backplanes contain VPD that has + a slot map. The slot map associates a SCSI LUN with a location label. Some + backplanes that do not actually have SES support have a virtual SES that + provides the same function. It is assumed that future protocols will support + equivalent function. + (that is, mounted/docked on a backplane + that supports location information for docked devices) will have physical + location codes. For example, + + + + U5734.001.10ABCDE-P3-D19 + + + + Physical device location codes are formed by appending the physical + device location label, Dn, to the location code of the resource to which the + device is docked. The location label, Dn, assigned in the engineering and + manufacturing process, is unique within the parent resource, is physically + displayed on the parent resource, and is present in the VPD of the parent + resource. + Notes: + + + AIX will use logical path location codes for SCSI devices even + in situations where a SES device is available to provide device location label + information. + + + + In some cases, a location code may need to be displayed or + logged before the information from the backplane is available to form the + physical location code. In these cases, a logical path location code will be + formed according to the applicable rules and used temporarily. Once the + information needed to form the physical device label is available, the physical + device location code will be used. + + +
+
+ +
+ SCSI Device Logical Path Location Codes -- Real and + Virtual + SCSI (Small Computer System Interface) devices whose parent does + not support location label VPD will have location codes that are composed of + the location code of the controlling SCSI port followed by the SCSI Target + (0-15) and SCSI LUN (Logical Unit Number). A SCSI logical-path example + is: + + + + U7043.150.1076543-P4-T3-L13-L0 + (Decimal L values) + + + + For virtual SCSI, a 48-bit ID is currently used (but is not limited + from moving to 64-bit) to identify the attached virtualized SCSI device. This + 48/64 bit ID is represented with a -L# in hexadecimal. There is no separate + LUN#. Examples are: + + + U7043.150.1076543-P4-T1-L830000000000 + (Hexadecimal L value) + + + or + + + U7043.150.1076543-P4-T3-W830000000000-L0 + (Hexadecimal W and L values) + + +
+ +
+ SAS Device Logical Path Location Codes + SAS (Serial SCSI) devices whose parent FRU does not support + location label VPD will have location codes that are composed of the location + code of the controlling SAS adapter followed by a series of port labels, + “-L#”, for each SAS port traversed from the adapter down to the + drive followed by the SCSI LUN (Logical Unit Number). The number value of the + “-L#” label will be the lowest phy in the outgoing SAS port with + # being a decimal value. For example: + + + U7043.150.1076543-P1-C3-L3-L1-L5-L0 + + +
+ +
+ IDE/ATAPI Device Logical Path Location Codes + The desired form of the location code is based on the physical-path + location codes obtained from VPD. For example: + + + + U5734.001.1076543-P2-D4 + + + + For an IDE device that had an older form of VPD (without physical + location codes), then its location code would have looked like: + + + + Ux-Px-(Cx)-Tx-L# + (from -L0 to -L3 where: + L0 = primary/master + L1 = primary/slave + L2 = secondary/master + L3 = secondary/slave) + + +
+ +
+ Fibre Channel Device Logical Path Location Codes -- + Real and Virtual + Fibre channel devices that are not mounted/docked on a backplane + that supports location code VPD will have location codes composed of the + location of the port on the controlling IOA followed by the worldwide unique + port identifier and LUN. The number value (#) of the “-L#” label + is a hexadecimal value. An example FC disk attached to a physical adapter + is: + + + + U787A.001.1012345-P1-C5-T2-W123456789ABCDEF0-L1A05000000000000 + + + + The same disk being accessed through virtual fibre channel would + appear like: + + + + U9111.520.1012345-V2-C4-T1-W123456789ABCDEF0-L1A05000000000000 + + +
+ +
+ Location Codes for SR-IOV Adapter Virtual + Functions + Single Root IO Virtualization allows for multiple “virtual + functions” to share the same physical port of a PCI adapter. The -S# + suffix, appended to the physical location code of the port (-T#), is used to + identify the unique virtual function using that port. The number value (#) of + the “-S#” label is a zero starting decimal value determined and + managed by the software layer that owns the physical functions of the SR-IOV + adapter. + For an SR-IOV ethernet adapter, the third virtual function for the + first ethernet port would look like: + + + + U7043.150.1076543-P1-C5-T1-S2 + + +
+ +
+ Group Labels + Group labels appear on parent FRUs to indicate groupings such as + port or DIMM pairs. Group labels are not part of the location label or location + code. Group labels may be part of slot map VPD and may be processed by software + that displays information on the corresponding FRUs. +
+ +
+ Sandwich FRU Location Label + A Sandwich FRU has a single location label to describe its location + just as any single FRU would. +
+ +
+ Sandwich FRU Child Location Labels + A Sandwich FRU is like any single FRU in that it has one numbering + space for numbering its child locations. +
+ +
+ Location Code Reported by Sensors + The location code reported by a sensor is the location code of the + FRU being monitored by the sensor. +
+ +
+ Sensor Locations + The location code of a sensor is the location code of the FRU on + which the sensor is located. +
+ +
+ Location Code Reported for Indicators + The VPD that reports an indicator will give the location label of + the resource identified by the indicator, not the location label of the + indicator itself. +
+ +
+ Indicator Locations + The location code of an indicator is the location code of the FRU + on which the indicator is located. +
+ +
+ Firmware Location Codes + The location specified for firmware is left to the platform except + that the location code must match the scope of the firmware and the location + code must follow the form specified above, beginning with a unit location label + and ending with a firmware location label. For example, firmware for port 2 (T + location label value) on planar 1 could have a location code of the form: + + + + U7879.001.1054321-P1-Y2 + + + + If the firmware is considered to be system wide, then the planar + location label would not be present and the unit location label specifies the + system location code not the CEC enclosure location code: + + + + U9117.001.1054321-Y1 + + +
+ +
+ Bulk Power Assembly (BPA) Location Codes + The unit location label for a BPA and its components consists of + the “U” prefix and the MTMS of the rack of which the BPA is a + component. + In some configurations, there are two BPAs in one rack. If they + were treated separately, the second BPA would have the same location label as + the first which would lead to location code collisions. Therefore, from the + perspective of location codes, the two BPAs will be treated as on BPA. The + planar location labels and, when necessary, other location labels within the + second BPA are incremented so that they are not the same as the labels in the + first BPA. For example, the front side BPA has a planar P1 and the back side + BPA has a planar P2 etc. +
+ +
+ Internal Battery Features Location Codes + The unit location label of an Internal Battery Feature (IBF) is the + unit location label of the BPA to which it belongs. The planar location labels + and, if necessary, other location labels within the IBF are incremented so that + they are not the same as the labels in the BPA or any other IBF belonging to + that BPA. +
+ +
+ Media Drawer Location Codes + In some configurations, there are media drawers that do not have a + MTMS. The unit location label for these media drawers is the unit location + label of the CEC to which it belongs. The planar location labels and, if + necessary, other location labels within the media are incremented so that they + are not the same as the labels in any other media drawer in the system or any + labels in the CEC. +
+ +
+ Horizontal Placement Location Labels + The horizontal placement location label begins with the prefix + “N” followed by the digit “1” for the left side of + the frame (viewed from the front) or the digit “2” for the right + side of the frame (when viewed from the front). +
+ +
+ EIA Location Label + The EIA location label begins with the prefix “X” + followed by a nonzero digit which represents the EIA location of the bottom of + the unit that is or would be in the frame at that location. +
+ +
+ Blade Chassis Location Codes + The disk storage module in a blade chassis may consist of a + backplane and a set of disks that plug into the backplane. Such a storage + module is assigned an enclosure feature code which is used to define the unit + location label (Un) of a disk in a storage module. + In some blade chassis there may be multiple identical storage + modules. All storage modules have a unit location with the same enclosure + feature code. The backplane within the left storage module has label P1, the + backplane in the next storage enclosure has label P2, and so on, to help with + disk identification. +
+ +
+ Location Codes for Hot-pluggable Devices + There are multiple occasions where devices may be added after the + system has booted and the addition did not use any dynamic reconfiguration + flows. In this situation, the O/S does not have adequate information from the + device tree's “ibm,loc-code” properties to + construct a correct physical location code. One example of this is with + IDE/SCSI drives that are hot-pluggable, where the O/S only knows the logical + location code from the IDE/SCSI bus. Firmware, however, may know the physical + location code of the drive based on the unit-address. Similarly, a USB root-hub + may have multiple down-facing ports with different physical location codes, but + the root-hub is only a single device tree node, so only a single location code + can be provided with just the “ibm,loc-code” property. + The “ibm,loc-code-map” property + contains a list of pairs (unit-address, location code), both as encoded + strings. It describes the physical location code for each potential child + node. + + + + R1--1. + + The instance of each USB root-hub in + the device tree must contain the “ibm,loc-code-map” property if the root-hub has multiple down-facing ports. This + applies to both the OHCI and EHCI interfaces of a USB adapter. Lack of this + property implies there is only a single down-facing root-hub port from that USB + interface. + + + + + R1--2. + + To determine the location code for an + end device associated with leaf open firmware node, the O/S must use the + “ibm,loc-code-map” entry with a matching + unit-address, if it exists, in preference to the parent's + “ibm,loc-code” property. + + + + + R1--3. + + The “ibm,loc-code-map” property must not contain an entry + for a port from an embedded IOA that is not externally connected, or if the + location code is undeterminable. + + + + + R1--4. + + If the unit-address architecture for + certain node types do not strictly bind a particular unit-address with a + hardware location, the “ibm,loc-code-map” + property must not exist in the parent of those nodes. + + + +
+ +
+ Location Code for USB Attached Devices + The root hub port number used determines the location code up to + the Tn suffix. There can be zero or many intervening hubs, and the intervening + “Ln” location labels are in path order. All immediate children + are of root hubs are represented by “L1”. For devices not + directly attached to the root hub, the “Ln” will correspond to + the software port number, n, of the parent hub that a device is attached to, + counting from 1. + For example, the location code for a USB device attached to an IOA + imbedded on a backplane with location label P1, using port T5, and with an + intervening hub under which the device is attached to the third port would + be: + + + + U787A.001.10ABCDE-P1-T5-L1-L3 + + +
+
+
+ +
+ Vital Product Data + +
+ Introduction + The set of all Vital Product Data (VPD) from the FRUs of a system + is the product topology information which uniquely defines that system’s + hardware and firmware elements. The system VPD describes a system in terms of + various FRUs, part numbers, serial numbers and other characterizing features. + With VPD, mechanisms may be provided for collecting information such as field + performance and failure data on any FRU in a system. Also, with the feedback + from the field into an installed system data base, the delivery of complete and + accurate Miscellaneous Equipment Specifications (MESs) to customers can be + assured. + + + + R1--1. + + FRUs used in LoPAR platforms must + provide machine-readable VPD as defined in + . + + + + + R1--2. + + LoPAR platforms must support the + collection of, and provide availability to, Vital Product Data. + + + + Platform Implementation Notes: + + + + It is the intent of this architecture that the FRUs of a system + be self describing using VPD. + + + + There are FRU’s which have VPD which is not in the format + described herein, such as JEDEC. In the case of use of these parts, the + firmware may choose to translate the FRU VPD data into the LoPAR format when + the OF device tree is being generated. For I/O adapters which have different + VPD, their device driver must perform the reading and translation. + + +
+ +
+ VPD Data Structure Description + Architecture Note: Even though only a few + large and small resource tags have been defined (see the + ), the current definition will allow all + possible tags except for (0x00). This will allow later devices with a new, + previously undefined tag, to work. + + + + R1--1. + + Vital Product Data when reported to the OS via + ibm,get-vpd or the OF device tree, must conform to the data + structures describe in the , section + 6.4The PCI 2.1 VPD keywords are PN, FN, + EC, MN, SN, LI, RL, RM, NA, DD, DG, LL, VI, FU, SI, and + Z0-ZZ, except as follows: + + + + The VPD will consist of only the following sequence of tags: + Large Resource type identifier string tag (type 2, byte 0 = 0x82) with FRU + name, Large Resource type VPD keywords tag (type 16, byte 0 = 0x90) with FRU + VPD keywords, Small Resource type end tag (type 15) with or without checksum + covering the above. + + + + Only resource tags, lengths and checksums are binary. All other + data must be in ASCII format. + + + + Architecture Note: There are three keywords + (FU, SI and VI) which allow binary data. There are no other exceptions. Also, + the length code following a large resource tag is Little-Endian. That is, the + first byte is the low order byte and the second byte is the high order byte of + the length. + Implementation Notes: + + + + Version 2.2 of the PCI Local Bus + Specification changed the format and location of VPD information. + With that change, a device with Version 2.2 VPD will result in no VPD being + detected by the firmware. In this case the selected device driver will have to + access and reformat the VPD information so that the format of the data provided + to the OS is in the format which is required by the OS. + + + + The definition of a small resource tag is where bit 7 is 0. Then + bit 6 through 3 are the type and bits 2 through 0 are the length. An end tag is + a type of 15. Thus a 0x78 is a small resource end tag of length 0 and 0x79 is a + small resource end tag of length 1. The valid end tags are 0x78 through + 0x7F. + + + + + + + R1--2. + + The end tag checksum, when provided to the OS, must cover all + resources beginning with the first byte (a resource tag) up to, but not + including, the Small Resource Type End tag. + + + + + R1--3. + + If the platform determines that the VPD that it has collected is + invalid, then the platform must discard any collected data and replace it + with: + + + + Large Resource type identifier string tag (type 2, byte 0 = 0x82) + with value ‘NOT_VALID_VPD’. + + + + Large Resource type VPD keywords tag (type 16, byte 0 = 0x90) + containing the “YL” keyword and associated location code + data. + + + + Small Resource Type End tag with or without a checksum covering + the above. + + + + + + + R1--4. + + If the device VPD is valid, all of the + device VPD must be transferred including the Small Resource Type End Tag. + + + + + R1--5. + + A “YL” keyword must be + added to the Large Resource type VPD keywords tag (type 16, byte 0 = 0x90) when + the VPD is reported to the OS via either the ibm,get-vpd + RTAS call or the OF device tree. + + + + The checksum byte after the (0x79) resource tag will cause the + binary sum of all the bytes from the first large resource tag, carries being + discarded, to result in 0x00. As noted in Requirement , the (0x79) small resource tag is not + included in this sum. +
+ +
+ Keyword Format Definition + The exact format of the VPD is vendor-specific but falls within the + specification as defined in the following subsections. + +
+ VPD fields + The fields defined in are + stored in VPD modules at the time of manufacturing. + + + + R1--1. + + LoPAR platforms and FRUs must + provide VPD fields marked as required in + and for all VPD fields provided must adhere + to the definitions specified by . + + + + + R1--2. + + Each system must have VPD that + contains the system’s SE keyword (see Requirements + , , + , and + ) and the system’s TM keyword (see + Requirements , + , , + and ). The description (large resource + type of 0x82) for this VPD in the “ibm,vpd” + property must be “System VPD”. + + + + + R1--3. + + VPD for memory FRUs must contain + the SZ keyword. + Platform Implementation Note: There are circumstances where vendor + preference or manufacturing processes may require that some fields be omitted + (for example; Serial Number). This should be treated as an exception and should + be accompanied by an appropriate level of risk assessment. In the case of an SN + exception, the SN should be omitted, not made blank, NULL, or a fixed + value. + + + + + + LoPAR VPD Fields + + + + + + + + + + + Keyword + + + + + Data Type + + + + + Data Length (Bytes) + + + + + Required?A lack of a hard requirement in this column does + not mean that the keyword is never required; only that it is not required all + the time. Keywords which are not marked as “Required” are + required when appropriate for the specific keyword. + + + + + Description + + + + + + + + A1 + + + ASCII + + + Up to 16 + + + -- + + + Storage Facility Image MTMS - Logical ID + Length (MTMS-a####). Linkage between logical entities. + Examples: Used on Disk FRU resource to link disk to array site. Used on array + site resource to link array site to array. Used on array resource to link array + to rank. Used on rank resource to link rank to segment pool. + + + + + AC + + + ASCII + + + Up to 32 + + + -- + + + Account Name + Used on HMC resource. + + + + + AD + + + ASCII + + + Up to 10 + + + -- + + + Addressing Field + + + + + AP + + + ASCII + + + Up to 16 + + + -- + + + Asset Protection Key Password + + + + + AS + + + ASCII + + + Up to 8 + + + -- + + + Reserved + + + + + AT + + + - + + + - + + + -- + + + Reserved + + + + + AX + + + ASCII + + + Up to 32 + + + -- + + + AIX name + + + + + B1 + + + ASCII + + + A multiple of 16, up to a max of 240 + + + -- + + + Contains 1 to 15 instances of the following 16 byte + definition, concatenated together. + Contains the base ethernet MAC address and an instance + count. + The count specifies the number of valid MAC addresses + starting with the base MAC address and incrementing by one for each successive + MAC address, until the specified number of MAC addresses have been + created. + The field contains the ASCII coded hexadecimal + representation of the binary value, as follows: + Bytes + 1 - 12 Base MAC address + 13 - 14 Reserved (ASCII “00”) + 15 - 16 Count + + + + + B2 + + + ASCII + + + A multiple of 32, up to a max of 224 + + + -- + + + Contains 1 to 7 instances of the following 32 byte + definition, concatenated together. + SAS WWIDs. + The Count field is the number of available WWIDs starting + from the base and incrementing by 1 for each new WWID. + The field contains the ASCII coded hexadecimal + representation of the binary value, as follows: + Bytes + 1 - 16 Base SAS WWID + 17 - 24 Reserved (ASCII “00000000”) + 25 - 32 Count + + + + + BC + + + ASCII + + + Up to 12 + + + -- + + + Bar Code + + + + + BH + + + ASCII + + + 2 + + + -- + + + BatcH code - used for vintage if no serial number + + + + + BR + + + ASCII + + + 2 + + + -- + + + Brand keyword value “xy” + Note: The following are the values + currently defined. To get other product specific values, go through the normal + LoPAR change process. + x = Type of machine + + + “B” - Reserved + + + “C” - Reserved + + + “D” - Reserved + + + “I” - Reserved + + + “N” - Reserved + + + “O” - Reserved + + + “P” - Reserved + + + “S” - IBM Power Systems™ platforms + + + “T” - OEM Power Systems platforms + + + Other values are reserved. + + + y = Specific Information + + + “0” - no specific information + + + Other values are reserved. + + + + + + + BT + + + ASCII + + + 10 + + + -- + + + Battery Replacement date in YYYY-MM-DD format. Used on + Primary Power Supply FRU in rack enclosure. + + + + + CC + + + ASCII + + + 4 + + + Required when a CCIN is required by code to configure or + service the component + + + Customer Card Identification Number (CCIN) + + + + + CE + + + ASCII + + + 1 + + + -- + + + CCIN Extender + + + + + CD + + + ASCII + + + Up to 10 + + + -- + + + Card ID + + + + + CI + + + ASCII + + + 16 + + + -- + + + CEC ID - of the CEC, that is the logical controller of + an MTMS (machine-type-model-serial #), like a drawer. + The 16 byte CI field definition is TTTT-MMM SSSSSSS where: + + + TTTT-MMM is an 8 byte field. The high order 4 bytes are + the system type, followed by a dash, followed by the 3 low order bytes which is + the model. + + + blank is a 1 byte separator character, that separates + the type-model from the serial #. + + + SSSSSSS is the 7 byte serial number. The high order 2 + bytes are the “plant of manufacture” and the low order 5 bytes + are the “sequence number”. + + + + + + + CL + + + ASCII + + + Up to 32 + + + -- + + + Code Level, LID keyword + Format: + fix pack MIF name, “space”, Load ID (8 + characters), time stamp (12 characters) + The fix pack name must be the same as the name used in + the MI keyword and is delimited by a space. + The time stamp is, hours (2 characters) + Minutes (2 + characters) + Year (4 characters) + Month (2 characters) + Day (2 characters). + The LID level reported is the current active level. + Note: There is no correlation + between the CL keyword value and which of the 3 candidate fixpack levels are + reported in the MI keyword. + + + + + CN + + + ASCII + + + Up to 7 + + + -- + + + Customer Number + + + + + CV + + + ASCII + + + Up to 4 + + + -- + + + Country Number + + + + + DC + + + ASCII + + + 2 + 1 + 12 +   +   +   +   +   +   +   +   +   +   +   +   +   +   +   +   +   +   + + + -- + + + Action Code, timestamp + blank (space) + TimeStamp: yyyymmddhhmm + Action Codes: + BD = Build Date + AM = added as MES + AB = added as bulk MES + AI = available at install + ID = field install date + AC = added with field EC + AU = added from unknown source + AR = added in repair action + AT = added temporarily in field + AH = added manually in field + Returned on history file: + RU = removed unknown (field) + RR = removed in repair action + RC = removed with EC + RT = removed temporarily / powered off (field) + RM = removed permanently (field) + RN = removed to another system + + + + + DD + + + - + + + - + + + -- + + + Reserved -- used for MicroChannel Architecture VPD + + + + + DG + + + - + + + - + + + -- + + + Reserved -- used for MicroChannel Architecture VPD + + + + + DU + + + ASCII + + + Up to 10 + + + -- + + + Drawer Unit + + + + + DL + + + ASCII + + + Up to 10 + + + -- + + + Drawer Level + + + + + DP + + + ASCII + + + Up to 255 + + + -- + + + Disk Space Characteristics + Used on Disk resource. Comma separated string. + Example (in the following, the “<“, + “>”, and text in between these would be replaced by a value + representing the quantity specified by the words between “<” + and “>”): + “VN=<Volume Serial Number>, + VD=<Vendor>, DT=<Disk Type>, DC=<Disk-Capacity>, + DR=<Disk-RPM>, DS=<Disk-Interface-Speed>, + AP=<Array-Site-Position>, ST=<Status>” + + + + + DS + + + ASCII + + + Up to 30 + + + -- + + + Displayable Message (if not defined, created by the + contents of the ID large resource (82)) + + + + + EA + + + ASCII + + + Up to 24 + + + -- + + + Electronic Message for electronic customer support (ECS) + + + + + EC + + + ASCII + + + 12 + + + Required if the part number is not changed with every modification + + + Engineering Change Level (technical features, revision level, vintage level) + + + + + ET + + + ASCII + + + 2 + + + -- + + + Enclosure Type. + This value is defined in the + . The ASCII value specified below is the + ASCII representation of the hexadecimal representation of the byte value + defined in the SMBIOS specification (for example, 0x0B becomes + “0B”). Bit 7 of the byte number is the chassis lock bit (if + present value is a 1, otherwise if either a lock is not present or it is + unknown if the enclosure has a lock, the value is a 0). If the chassis lock bit + is set, the following get changed to the corresponding ASCII representation + (for example, “01” becomes “81”, “10” + becomes “90”) + “01” Other + “02” Unknown + “03” Desktop + “04” Low Profile Desktop + “05” Pizza Box + “06” Mini Tower + “07” Tower + “08” Portable + “09” LapTop + “0A” Notebook + “0B” Hand Held + “0C” Docking Station + “0D” All in One + “0E” Sub Notebook + “0F” Space-saving + “10” Lunch Box + “11” Main Server Chassis + “12” Expansion Chassis + “13” SubChassis + “14” Bus Expansion Chassis + “15” Peripheral Chassis + “16” RAID Chassis + “17” Rack Mount Chassis + “18” Sealed-case PC + + + + + FC + + + ASCII + + + 8 + + + -- + + + The Feature Code is 8 bytes formatted as 4 characters, a + dash, and three characters. + + + + + FD + + + ASCII + + + 7 + + + -- + + + Field Bill of Material (FBM) EC level + + + + + FG + + + ASCII + + + 4 + + + -- + + + FlaG Field: The first two bytes contain a VPD flag in + the form of VS. V=V indicates that there is VPD. V=N indicates there is no VPD. + S=S indicates that the VPD contains a slot map. S=P indicates there is a port + map. S=N indicates no slot map or port map. S=B indicates both a slot map and a + port map. The right two characters contain the FRU identification + keyword. + + + + + FI + + + ASCII + + + 2 - 8 + + + -- + + + Frame ID: 2 hex byte value for SPCN or 8 character + logical frame number for DASD backplane. + + + + + FL + + + ASCII + + + Up to 16 + + + -- + + + FRU Label: This is a variable length ASCII character + data area for the FRU Label. + + + + + FN + + + ASCII + + + Up to 8 + + + Required + + + FRU Number (Board, card, or assembly Field Replacement + Unit number). + + + + + FU + + + Binary + + + Up to 10 + + + -- + + + Function Unit - This function identifies which function + in a multi-function IOA this VPD data applies to. Only one FU field can appear + per VPD tag. Data is binary encoded. + + + + + H1 + + + ASCII + + + 1 + + + -- + + + Partition HSL Pool + Used on a partition resource that is part of a storage facility image. + + + + + ID + + + ASCII + + + 2 + + + -- + + + Two ASCII characters are used to identify each system in + a Storage Facility. Valid values are 00 and 01. + + + + + IF + + + ASCII + + + Up to 16 + + + -- + + + Storage Facility MTMS - InterfaceID + Length (MTMS-####). Identifies one or more adapter I/O + interfaces in the storage facility that interconnect device adapters and + storage enclosures. Used on Device Adapter FRUs in I/O enclosure and on Storage + Enclosures. Device Adapters have two Interfaces Ids (comma separated string), + and storage enclosures have one. The number could change for future + products. + + + + +   + L1 + L2 + L3 + L4 + L5 + L6 + + + ASCII + + +   + Up to 30 + Up to 30 + Up to 30 + Up to 10 + Up to 30 + Up to 12 + + + -- + + + Location Information: + Individual or Company Name + Street Address + City, State, Country + Zip Code + Contact Name + Contact Phone Number + + + + + LA + + + ASCII + + + 32 + + + -- + + + LIC Node Alternate Bus VPD: This fixed format data field + contains 32 bytes of LIC I/O node alternate bus VPD data. + + + + + LE + + + ASCII + + + Up to 17 + + + -- + + + LIC VMRF + Example: SEA 5.1.0.0345. Used on a partition resource + that is part of a storage facility image or on an enclosure or enclosure + resource that has a firmware level. + + + + + LI + + + ASCII + + + Up to 10 + + + -- + + + Adapter Software Identification + + + + + LL + + + ASCII + + + Up to 10 + + + -- + + + Adapter Software Level + + + + + LN + + + ASCII + + + 32 + + + -- + + + LIC Node VPD: Fixed format 32 bytes of VPD data. + + + + + LO + + + ASCII + + + 2 + + + -- + + + Location (INternal/EXternal) + + + + + LP + + + ASCII + + + 32 + + + -- + + + LIC Node Primary Bus VPD: Fixed format 32 bytes of VPD data. + + + + + LS + + + ASCII + + + Up to 255 + + + -- + + + Logical Space Characteristics + Used on Storage Logical resources. + Examples: + Used on Array resource. Comma separated string. + Including: “AN=Array Serial Number, AT=Array-Type, AC=Array + Configuration, Rank Position”. + Used on Rank resource. Comma separated string. Including: + “RN=Rank Serial Number, ST=Segment-Type(FB-1G, CKD-Mod1), + SS=Segments(####), SU=Segments-Used, RG=Rank Group(#)”. + Used on Segment Pool resource. Comma separated string. + Including: “ST=Segment-Type(FB-1G, CKD-Mod1), SS=Segments(####), + SU=Segments-Used, VS=Virtual-Segments(####), + VU=Virtual-Segments-Used(####)”, RG=Rank-Group(#). + + + + + MD + + + ASCII + + + 4 + + + -- + + + Model Number: 3 characters with a leading blank. + + + + + MF + + + ASCII + + + 2 + + + -- + + + Map Format: Two hex characters identify the slot or port + map format that follows. This keyword must immediately precede the SM or PM + keyword. + + + + + MI + + + ASCII + + + Up to 40 + + + -- + + + Microcode Image + This keyword is only used to describe dual sided + alterable system firmware Image which can be altered by the OS via the + ibm,update-flash-64-and-reboot RTAS call. Both the + ibm,validate-flash-image and the + ibm,manage-flash-image RTAS calls are supported. May or may not be + able to be updated via non-OS visible means. + Format: + t side Microcode Image name, “space”, p + side Microcode Image name, “space”, booted Microcode Image + name + The Microcode Image name must be a 9 character name of + the form: + “NNSSS_FFF” + + where + “NN” is a two character name (assigned by + the GFW Firmware Distribution Coordinator) used to identify a set of + platforms; + “SSS” is a 3 character code stream + indicator; + “_” is a separation character for + readability; and, + “FFF” is a 3 character identifier of the + current microcode level. + Note: The booted fix pack level + reported may not match the current p-side or t-side level as a result of + concurrent update. The important information is what is in flash, and that is + what is being reported. The hypervisor will have to cache the value for the + booted level, and should go to FSP to check what's current on flash for the + p-side and t-side levels. + + + + + ML + + + ASCII + + + Up to 40 + + + -- + + + Microcode Level + This keyword is only used to describe dual sided + alterable system firmware images which can be altered by the OS via the + ibm,update-flash-64-and-reboot RTAS call. Both the ibm,validate-flash-image and + the ibm,manage-flash-image RTAS calls are supported. May or may not be able to + be updated via non-OS visible means. + Format: + t side Microcode Level name, “space”, p + side Microcode Level name, “space”, booted Microcode Level + name + The Microcode Image name must be a 8 character name of the form: + “FWVRE.MF” + + where + "FW" is a static prefix representing 'firmware' + “V” is Version - Power Processor Level + "R" is Revision - Typically GA number from the processor level + "E" is Extension - Typically zero. If non-zero, + designates off cycle single system release + "M" is Modification - associated Service Pack Level (0-Z) + "F" is Fix Level - Typically zero. If non-zero, designate + off cycle, targeted fixes + Note: The booted fix pack level + reported may not match the current p-side or t-side level as a result of + concurrent update. The important information is what is in flash, and that is + what is being reported. The hypervisor will have to cache the value for the + booted level, and should go to FSP to check what's current on flash for the + p-side and t-side levels. + + + + + MN + + + ASCII + + + 10 + + + -- + + + Manufacturer ID (source of device, name and location) + + + + + MP + + + ASCII + + + 3 + + + -- + + + Module Plug count. This counter keeps track of the + numbers of times a module has been plugged, so that reliability statistics can + be kept. + + + + + MS + + + ASCII + + + Up to 6 + + + -- + + + MES Number + + + + + MU + + + ASCII + + + 32 + + + -- + + + Machine Universal Unit ID (UUID). The value is the ASCII + coded hexadecimal representation of the 16 byte binary value. + + + + + N5 + + + ASCII + + + Up to 228 + + + -- + + + Processor CoD Capacity Card Info + + + + + N6 + + + ASCII + + + Up to 231 + + + -- + + + Memory CoD Capacity Card Info + + + + + N7 + + + ASCII + + + Up to 144 + + + -- + + + Processor on Demand billing data + + + + + N8 + + + ASCII + + + Up to 145 + + + -- + + + Memory on Demand billing data + + + + + NA + + + ASCII + + + Up to 16 + + + -- + + + Network Address (ASCII coded hexadecimal representation + of the binary value.) + + + + + NC + + + ASCII + + + Up to 25 + + + -- + + + This keyword is used to describe the prefix name of the + file used to install a single sided alterable system firmware or adapter/device + microcode image. When this keyword is present, the complete file name will be + described by the content of the NC keyword, concatenated with + “.”, concatenated with the content of the RM keyword. + + + + + NN + + + ASCII + + + 16 + + + -- + + + World Wide Node Name - IEEE assigned 64 bit identifier + (16 hexadecimal digits) for Storage Facility. Valid values are 0-9, A-F. + + + + + NT + + + ASCII + + + Up to 32 + + + -- + + + Sub-machine type + + + + + NV + + + ASCII + + + Up to 24 + + + -- + + + NVRAM ID, part number, location and size + + + + + NX + + + - + + + - + + + -- + + + Reserved + + + + + OS + + + ASCII + + + Up to 17 + + + -- + + + OS name and level. + The OS level is shown in the form of: V.R.M.F where V is + the version, R is the release, M is the modification, and F is the fix. + + + + + PA + + + ASCII + + + 1 + + + -- + + + Op Panel installed flag. “Y” = yes a panel + is installed, “N” = no a panel is not installed. The absence of + this keyword means, that an Op Panel is installed. + + + + + PC + + + ASCII + + + Up to 16 + + + -- + + + Processor Component Definition + + + + + PD + + + ASCII + + + Up to 8 + + + -- + + + Power dissipation/consumption + + + + + PI + + + ASCII + + + Up to 8 + + + -- + + + Processor ID or unique ID (used for licensing control) + + + + + PL + + + ASCII + + + Up to 32 + + + -- + + + Location code + + + + + PM + + + ASCII + + + Up to 16 + + + -- + + + Port Map: Contains the RIO Port Map label information. + Must be preceded by the MF keyword. + + + + + PN + + + ASCII + + + 12 + + + Required if it is different from the FRU number + (FN) + + + Part number of assembly. + + + + + PO + + + ASCII + + + Up to 16 + + + -- + + + SPCN VPD: Identification of the SPCN VPD area on the I/O + backplane. + + + + + PP + + + ASCII + + + 32 + + + -- + + + Power Parameters: SPCN field identifying Power node + parameters. + + + + + PR + + + ASCII + + + 16 + + + -- + + + Power: 16 ASCII hexadecimal characters that represent + the 8 bytes of binary information for Power Control. + + + + + R1 + + + ASCII + + + Up to 16 + + + -- + + + Rack MTMS - Rack Location + Length (MTMS-Exx). - used on storage enclosure + resources. + + + + + R2 + + + ASCII + + + 1 + + + -- + + + Rack Number + Used on Rack enclosure resources. Provides an ordered + number of racks in the storage facility. + + + + + RA + + + - + + + - + + + -- + + + Reserved + + + + + RD + + + ASCII + + + 16 + + + -- + + + Power Domain ID - is the MTMS of the BPA, that powers an + MTMS (Machine-Type-Model-Serial #), like a CEC or drawer. + The 16 byte RD field definition is: TTTT-MMM SSSSSSS where: + + + TTTT-MMM is an 8 byte field. The high order 4 bytes are + the system type, followed by a dash, followed by the 3 low order bytes which is + the model. + + + blank is a 1 byte separator character, that separates + the type-model from the serial #. + + + SSSSSSS is the 7 byte serial number. The high order 2 + bytes are the “plant of manufacture” and the low order 5 bytes + are the “sequence number”. + + + + + + + RI + + + ASCII + + + 4 + + + -- + + + Power Resource ID: A 4 byte hex field providing a unique + logical ID for the power resource. + + + + + RJ + + + ASCII + + + Up to 16 + + + -- + + + RIO-G Loop + Used on I/O enclosure resource. Identifies RIO-G loop on + the reporting system. + + + + + RK + + + ASCII + + + 16 + + + -- + + + Rack Unique ID - is the 64 bit Dallas + “1-wire” unique ROM code. The first 8 bits are a 1-Wire family + code. The next 48 bits are a unique serial number. The last 8 bits are a CRC of + the first 56 bits. + Each of the 16 4-bit nibbles are converted to 16 ASCII + characters, in the range 0-9 or A-F. + + + + + RL + + + ASCII + + + Up to 24 + + + -- + + + This keyword is only used to describe single sided + non-alterable system firmware or adapter/device microcode image which can not + be altered by any means; OS visible or non-OS visible. A single alphanumeric + character string that defines the level of the image. + ROM id, Location ID, ROM part number, FW part number, FW + level, FW code, release date, FW size. + + + + + RM + + + ASCII + + + Up to 25 + + + -- + + + This keyword is only used to describe single sided + alterable system firmware or adapter/device microcode image which can be + altered by the OS. The OS alters the system firmware image via the + ibm,update-flash-64-and-reboot RTAS call. Neither the + ibm,validate-flash-image nor the + ibm,manage-flash-image RTAS calls are supported. May or may not be + able to be updated via non-OS visible means. A single alphanumeric character + string that defines the level of the image. + ROM id, Location ID, ROM part number, FW part number, FW + level, FW code, release date, FW size + + + + + RN + + + ASCII + + + Up to 2 + + + -- + + + Rack Name + + + + + RP + + + ASCII + + + 1 + + + -- + + + RIO-G Position Offset + Used on I/O enclosure resource. Identifies the distance + in enclosures from the reporting system - first enclosure is offset 1. + + + + + RS + + + ASCII + + + Up to 128 + + + -- + + + IBM LoPAR Compliant platform unique VPD: Start of a data area. + + + + + RT + + + ASCII + + + 4 + + + -- + + + Record Type. Contains a four character Record Name that + represents a VPD Definition. The following list associates Record Names with + their VPD Definitions. + + + “VSYS” - System MTMS VPD + + + “VCEN” - Enclosure MTMS VPD + + + “VINI” - FRU VPD record + + + + + + + RW + + + - + + + - + + + -- + + + Reserved + + + + + RX + + + ASCII + + + Up to 25 + + + -- + + + This keyword is only used to describe single sided + microcode image which can not be altered by the OS, but may be updated via + non-OS visible means. A single alphanumeric character string that defines the + level of the image. + + + + + S1 + + + ASCII + + + Up to 8 + + + -- + + + Serial Number of attached machine + + + + + S3 + + + ASCII + + + 16 + + + -- + + + Storage Facility MTMS + Length (MTMS). Used on system resource, partition + resources, array-site, resources, array resources, rank resources, storage pool + resources, and enclosure resources in a storage facility to identify the + storage facility. + + + + + S4 + + + ASCII + + + Up to 16 + + + -- + + + Storage Facility Image MTMS + Length (MTMS). Used on partition, array-site, array, + rank, and storage pool, and enclosure-FRU resources, associated with a storage + facility image. + + + + + SC + + + ASCII + + + Up to 44 + + + -- + + + Specify codes + + + + + SE + + + ASCII + + + Up to 7 + + + See Requirements + , + , + , + , and + + + + Machine or Cabinet Serial Number. + + + + + SF + + + ASCII + + + Up to 8 + + + -- + + + Field Change Shipping Instruction (FCSI) number + + + + + SG + + + ASCII + + + 7 + + + -- + + + 2 high order bytes are the “plant of manufacture + code”, followed by the low order 5 bytes, which are the “unit + sequence number”. This unit sequence number must be DDDD0, ADDD0, AADD0, + AAAD0, or AAAA0 where D is a digit 0-9 and A is an alphabetic character A-Z + excluding E, I, J, O, Q, S, U. The right most character of the unit sequence + number must be set to 0. + + + + + SI + + + Binary + + + Up to 10 + + + -- + + + Subsystem Vendor ID. Data is binary encoded. + + + + + SL + + + - + + + - + + + -- + + + Reserved + + + + + SM + + + ASCII + + + Up to 16 + + + -- + + + Slot Map: Contains Slot Map information. Must be + preceded by the MF keyword. + + + + + SN + + + ASCII + + + 12 + + + Required and must be unique for each part with the same FN + + + Serial Number 12 characters. + + + + + SU + + + ASCII + + + 12 + + + See notes + + + The System Unique Identifier (SUID) is a twelve + hexadecimal character value that is unique to a given system anywhere in the + world. The number range is obtained from the Institute of Electrical and + Electronic Engineers. There are no IBM asset protection considerations + involved. + + + + + SY + + + ASCII + + + 7 + + + -- + + + System Number (only one allowed) + + + + + SZ + + + ASCII + + + Up to 10 + + + For memory FRUs, see Requirement + + + + + + Size in decimal, with no leading zeroes. For memory (for + example, cards and DIMMs), it provides the memory size in MB’s. As an + example, a 32 GB memory card would be coded as 32768. + + + + + Tl + + + ASCII + + + 8 + + + -- + + + Attached machine type-model + + + + + TM + + + ASCII + + + 8 + + + See Requirements + , + , + , + , and + + + + The high order 4 bytes are the “Machine + Type”, the next byte is a dash, followed by the 3 byte + “Model”. + + + + + TN + + + ASCII + + + 8 + + + -- + + + The high order 4 bytes are the “Machine + Type”, the next byte is a dash, followed by the 3 byte + “Model”. + + + + + U1 + + + ASCII + + + Up to 255 + + + -- + + + Logical Configuration String + Used on a partition resource that is: CKD3380=####, + CKD3390=####, SCSI512=####, SCSI520=####, SCSI Host Ports=####, SCSI LUN + Groups=####. + Used on device adapter or host adapter FRU for logical + configuration information, if any. + Used on Storage Enclosure. Comma separated string + including “BA=Base Address(xx)”. + + + + + U2 + + + ASCII + + + Up to 255 + + + -- + + + Host Inventory + Used on a partition resource that is part of a storage + facility image for storage facility image logical configuration. Comma + separated string. Including: “Host OS Type1=####, Host OS Type 2=####, . + . .”. + + + + + U3 + + + ASCII + + + Up to 255 + + + -- + + + Reserved for future use. Used on partition resource or + Storage Configuration resources. + + + + + U4 + + + ASCII + + + Up to 255 + + + -- + + + Reserved for future use. Used on partition resource or + Storage Configuration resources. + + + + + U5 + + + ASCII + + + Up to 255 + + + -- + + + Reserved for future use. Used on partition resource or + Storage Configuration resources. + + + + + U6 + + + ASCII + + + Up to 255 + + + -- + + + Reserved for future use. Used on partition resource or + Storage Configuration resources. + + + + + U7 + + + ASCII + + + Up to 255 + + + -- + + + Reserved for future use. Used on partition resource or + Storage Configuration resources. + + + + + U8 + + + ASCII + + + Up to 255 + + + -- + + + Reserved for future use. Used on partition resource or + Storage Configuration resources. + + + + + U9 + + + ASCII + + + Up to 255 + + + -- + + + Reserved for future use. Used on partition resource or + Storage Configuration resources. + + + + + VE + + + - + + + - + + + -- + + + Reserved -- used for MicroChannel Architecture VPD + + + + + VI + + + Binary + + + Up to 10 + + + -- + + + Vendor ID / Device ID + Only one VI may appear per VPD tag. + + + + + WN + + + ASCII + + + 16 + + + -- + + + Contains the ASCII coded hexadecimal World Wide Port + Name (WWPN). + + + + + YK + + + ASCII + + + 4 + + + See Requirement + + + Ties together multiple enclosures that share the same + combined SE and TM. + + + + +
+ Notes referenced in : + + + + When the + BR keyword indicates “S” or “T” for the type of + machine, this field must be present and must be non-blank. + + + Implementation Note: The following keywords + are defined in this architecture with the same or similar usage: AD, CD, DC, + DL, DS, DU, EC, FC, FN, LO, NA, P C, PI, PN, RL, RN, SN, SZ, TM, and US. +
+ +
+ Additional Fields for Product Specific use + Three fields are available for user, system or product specific + data for which no unique keyword has been defined. The first and second ranges + of fields in the list are not addressed in the PCI Specifications and are + unique to LoPAR platforms. + + + + U0 - UZ User specific + + + + N0 - NF ReservedV0 - VF Reserved + + + + Y0 - YZ System Information specific + + + + Z0 - ZZ Product specific + + + Note: If firmware/software has a specific + need for a keyword, then it must be provided by the appropriate component + VPD. + The Y? and Z? fields defined in + are specific to LoPAR platforms. As a need + for these fields is determined, they will be defined in this document. The + table contains several keywords which have been defined as place holders. + + + LoPAR Usage of Product Specific VPD Fields + + + + + + + + + + Keyword + + + + + Data Type + + + + + Data Length (Bytes) + + + + + Description + + + + + + + + N5 + + + ASCII + + + Up to 56 + + + Processor CoD Capacity Card Info per + + + + + N6 + + + ASCII + + + Up to 56 + + + Memory CoD Capacity Card Info per + + + + + U? + + + ASCII + + + Up to 128 + + + User Data:? = 0...9, A...Z + + + + + Y0 + + + ASCII + + + 64 + 2 + 2 + 24 + 24 + 12 + + + Board Repair Actions: + # times board repaired + # times board updated with code patches + Copy of system ID Y2 field + Copy of system ID TM field + Copy of system ID PI field + + + + + Y1 + + + ASCII + + + 24 + 2 + 2 +   + 8 + 12 + + + Error Descriptor: + # allowable messages + # valid messages + Messages of 20 bytes each, first, last and most recent 4 messages + Error Code + Date/Time Stamp: yyyymmddhhmm + + + + + Y2 + + + ASCII + + + 24 + 4 + 4 + 4 + 12 + + + Only in system VPD EEPROM: + Manufacturer’s Location + Machine Type + Model ID + Cabinet Serial Number + + + + + YK + + + ASCII + + + Up to 4 + + + Ties together multiple enclosures that share the same + combined SE and TM. See Requirement + . + + + + + YL + + + ASCII + + + Up to 255 + + + Hardware Location Code (see ) + + + + + Z? + + + ASCII + + + Up to 255 + + + Product Specific Information: may be keyword oriented + and ‘,’ delimited. + + + + +
+
+
+
+ diff --git a/Platform/ch_smp.xml b/Platform/ch_smp.xml new file mode 100644 index 0000000..50bf499 --- /dev/null +++ b/Platform/ch_smp.xml @@ -0,0 +1,373 @@ + + + The Symmetric Multiprocessor Option + + This architecture supports the implementation of symmetric + multiprocessor (SMP) systems as an optional feature. This Chapter provides + information concerning the design and programming of such systems. For SMP OF + binding information, see . + SMP systems differ from uniprocessors in a number of ways. These + differences are not all covered in this chapter. Other chapters that cover + SMP-related topics include: + + + + Non-processor-related initialization and other requirements: + + + + + Interrupts: + + + + Error handling: + + + + Many other general characteristics of SMPs—such as + interprocessor communication, load/store ordering, and cache + coherence—are defined in . + Requirements and recommendations for system organization and time base synchronization are + discussed here, along with SMP-specific aspects of the boot process. + SMP platforms require SMP-specific OS support. An OS supporting only + uniprocessor platforms + may not be usable on an SMP, even when an SMP platform has only a single + processor installed; conversely, an SMP-supporting OS may not be usable on a + uniprocessor. It is, however, a requirement that uniprocessor OSs be able to + run on one-processor SMPs, and that SMP-enabled OSs also run on uniprocessors. + See the next section. + +
+ SMP System Organization + This chapter only addresses SMP multiprocessor platforms. This is a + computer system in which multiple processors equally share functional and + timing access to and control over all other system components, including memory + and I/O, as defined in the requirements below. Other + multiprocessor organizations (“asymmetric + multiprocessors,” “ attached + processors,” etc.) are not included in this architecture. These might, + for example, include systems in which only one processor can perform I/O + operations; or in which processors have private memory that is not accessible + by other processors. + Requirements through + , further require that all processors + be of (nearly) equal speed, type, cache characteristics, etc. Requirements for + optional non-uniform multiprocessor platforms are found in + . + + + + R1--1. + + OSs that do not explicitly support the SMP option must support + SMP-enabled platforms, actively using only one processor. + + + + + R1--2. + + For the Symmetric Multiprocessor + option: SMP OSs must support uniprocessor platforms. + + + + + R1--3. + + For the Symmetric Multiprocessor + option: The extensions defined in + , and the SMP support section of the RTAS + specifications (see ) must be implemented. + + + + + R1--4. + + For the Symmetric Multiprocessor or Power Management + option: All processors in the configuration must have equal + functional access and “quasi-equal” + timing access to all of system memory, + including other processors’ caches, via cache coherence. + “Quasi-equal” means that the time required for processors to + access memory is sufficiently close to being equal that all software can ignore + the difference without a noticeable negative impact on system performance; and + no software is expected to profitably exploit the difference in timing. + + + + + R1--5. + + For the Symmetric Multiprocessor option: + All processors in the configuration must have equal functional and + “quasi-equal” + timing access to all I/O devices and IOAs. + “Quasi-equal” is defined as in Requirement , + above, with I/O access replacing memory access for this case. + + + + + R1--6. + + For the Symmetric Multiprocessor option: + SMP OSs must at least support SMPs with the same PVR contents and speed. The + PVR contents includes both the PVN and the revision number. + + + + + R1--7. + + For the Symmetric Multiprocessor option: + All caches at the same hierarchical level must have the same OF properties. + + + + + R1--8. + + Hardware for SMPs must provide a means for synchronizing all the + time bases of all the processors in the platform, for use by platform firmware. + See . This is for purposes of clock synchronization + at initialization and at times when the processor loses time base state. + + + + + R1--9. + + The platform must initialize and maintain the synchronization of + the time bases and timers of all platform processors such that; for any code + sequence “C”, run between any two platform processors + “A” and “B”, where the reading of the time base or + timer in processor “A” can be architecturally guaranteed to have + happened later in time than the reading of the time base or timer in processor + “B”, the value of the time base read by processor + “A” is greater than or equal to the value of the time base read + by processor “B”. + + + + + Software Implementation Notes: + + + + Requirement has + implications on the design of uniprocessor OSs, particularly regarding the + handling of interrupts. See the sections that follow, particularly + . + + + + While Requirement does + not require this, OSs are encouraged to support processors of the same type but + different PVR contents as long as their programming models are + compatible. + + + + Because of performance penalties associated with inter-processor + synchronization, the weakest synchronization primitive that produces correct + operation should be used. For example, eieio can often be + used as part of a sequence that unlocks a data structure, rather than the + higher-overhead but more general sync instruction. + + + + Hardware Implementation Notes: + + + Particularly when used as servers, SMP systems make heavy demands + on the I/O and memory subsystems. Therefore, it is strongly recommended that + the I/O and memory subsystem of an SMP platform should either be expandable as + additional processors are added, or else designed to handle the load of the + maximum system configuration. + + + + Defining an exact numeric threshold for + “quasi-equal” is not feasible because it depends on the + application, compiler, subsystem, and OS software that the system is to run. It + is highly likely that a wider range of timing differences can be absorbed in + I/O access time than in memory access time. An illustrative example that is + deliberately far from an upper bound: A 2% timing difference is certainly + quasi-equal by this definition. While significantly larger timing differences + are undoubtedly also quasi-equal, more conclusive statements must be the + province of the OS and other software. + + +
+ +
+ An SMP Boot Process + Booting + an SMP entails considerations not present when booting a + uniprocessor. This section indicates those considerations by describing a way + in which an SMP system can be booted. It does not pretend to describe + “the” way to boot an SMP, since there are a wide variety of ways + to do this, depending on engineering choices that can differ from platform to + platform. To illustrate the possibilities, several variations on the SMP + booting theme will be described after the initial description. + This section concentrates solely on SMP-related issues, and ignores a + number of other initialization issues such as hibernation and suspension. See + for a discussion of those other + issues. + +
+ SMP-Safe Boot + The basic booting process described here is called + “SMP-Safe” because it tolerates the presence of multiple + processors, but does not exploit them. This process proceeds as follows: + + + + At power on, one or more finite state machines (FSMs) built into + the system hardware initialize each processor independently. FSMs also perform + basic initialization of other system elements, such as the memory and interrupt + controllers. + + + + After the FSM initialization of each processor concludes, it + begins execution at a location in ROM that the FSM has specified. This is the + start of execution of the system firmware that eventually provides the OF + interfaces to the OS. + + + + One of the first things that firmware does is establish one of the processors as the + master: The + master is a single processor which + continues with the rest of the booting process; all the others are placed in a + stopped state. A processor in this + stopped state is out of the picture; it does nothing that affects + the state of the system and will continue to be in that state until awakened by + some outside force, such as an inter-processor interrupt (IPI).Another + characteristic of the stopped state, + defined in , is that the + processor remembers nothing of its prior life when placed in a + stopped state; this distinguishes it from the + idle state. That isn’t strictly necessary for this booting + process; idle could have been used. However, since the + non-master processor must be in the + stopped state when the OS is started, + stopped might as well be used. + One way to choose the master is to include a special register + at a fixed address in the memory controller. That special register has the + following properties: + + + + The FSM initializing the memory controller sets this + register’s contents to 0 (zero). + + + + The first time that register is read, it returns the value 0 and + then sets its own contents to non-zero. This is performed as an atomic + operation; if two or more processors attempt to read the register at the same + time, exactly one of them will get the 0 and the rest will get a non-zero + value. + + + + After the first attempt, all attempts to read that + register’s contents return a non-zero value. + + + + The master is then picked by having all the + processors read from that special register. Exactly one of them will receive a + 0 and thereby become the master. + Note that the operation of choosing the + master cannot be done using the PA memory locking instructions, + since at this point in the boot process the memory is not initialized. The + advantage to using a register in the memory controller is that system bus + serialization can be used to automatically provide the required + atomicity. + + + + The master chosen in step + then proceeds to do the remainder of the + system initialization. This includes, for example, the remainder of Power-On + Self Test, initialization of OF, discovery of devices and construction of the + OF device tree, loading the OS, starting it, and so on. Since one processor is + performing all these functions, and the rest are in a state where they are not + affecting anything, code that is at least very close to the uniprocessor code + can be used for all of this (but see + below). + + + + The OS begins execution on the single + master processor. It uses the OF Client Interface + Services to start each of the other processors, taking them out of the + stopped state and setting them loose on the SMP OS code. + This completes the example SMP boot process. Variations are + discussed beginning at . Before + discussing those variations, an element of the system initialization not + discussed above will be covered. + + + +
+ +
+ Finding the Processor Configuration + Unlike uniprocessor initialization, SMP initialization must also + discover the number and identities of the processors installed in the system. + “Identity” means the interrupt address of each processor as seen + by the interrupt controller; without that information, a processor cannot reset + interrupts directed at it. This identity is determined by board wiring: The + processor attached to the “processor 0” wire from the interrupt + controller has identity 0. For information about how this identity is used, see + . + The method used by a platform to identify its processors is + dependent upon the platform hardware design and may be based upon service + processor information, identification registers, inter-processor interrupts, or + other novel techniques. +
+ +
+ SMP-Efficient Boot + The booting + process as described so far tolerates the existence of multiple processors but + does not attempt to exploit them. It is possible that the booting process can + be sped up by actively using multiple processors simultaneously. In that case, + the pick-a-master technique must still be + used to perform sufficient initialization that other inter-processor + coordination facilities—in-memory locks and IPIs—can be used. + Once that is accomplished, normal parallel SMP programming techniques can be + used within the initialization process itself. +
+ +
+ Use of a Service Processor + A system might contain a service processor that is distinct from the processors + that form the SMP. If that service processor has suitably intimate access to + and control over each of the SMP processors, it can perform the operations of + choosing a master and discovering the SMP processor + configuration. +   +
+
+ diff --git a/Platform/ch_system_reqs.xml b/Platform/ch_system_reqs.xml new file mode 100644 index 0000000..d3f4d16 --- /dev/null +++ b/Platform/ch_system_reqs.xml @@ -0,0 +1,2624 @@ + + + System Requirements + + This chapter gives an operational overview of LoPAR systems and + introduces platform specific software and/or firmware components that are + required for OS support. This chapter also addresses some system level + requirements that are broad in nature and are fundamental to the architecture + described in later chapters. Lastly, a table of requirements is presented as a + guide for platform providers. + +
+ System Operation +
+ Control Flow + is an example of typical + phases of operation from power-on to full system operation to termination. This + section gives an overview of the processes involved in moving through these + phases of operation. This section will introduce concepts and terms that will + be explained in more detail in the following chapters. Most requirements + relating to these processes will also appear in later chapters. + The discussion in this chapter will be restricted to systems with a + single processor. Refer to for the + unique requirements relating to multiprocessor systems. + +
+ Phases of Operation (example) + + + + + + + + +
+
+ +
+ POST + + Power On Self Test (POST) is the process by which the + firmware tests those areas of the hardware that are critical to its ability to + carry out the boot process. It is not intended to be all-inclusive or to be + sophisticated in how it relates to the user. Diagnostics with these + characteristics will generally be provided as a service aid. + Platform Implementation Note: The platform + may choose to utilize a service processor to assist in the implementation of + functions during various phases of operation. The service (or support) + processor is not a requirement of this architecture, but is usually seen in the + larger systems. +
+ +
+ Boot Phase + The following sections describe the boot phase of operation. The + fundamental parts of the boot phase are: + + + + Identify and configure system components. + + + + Generate a device tree. + + + + Initialize/reset system components. + + + + Locate an OS boot image. + + + + Load the boot image into memory. + + + +
+ Identify and Configure System Components + Firmware is generally written with a hardware in mind, so some + components and their configuration data can be hardcoded. Examples of these + components are: type of processor, cache characteristics, and the use of + imbedded components on the planar. This hardcoding is not a requirement, only a + practical approach to a part of this task. + + + + R1--1. + + The firmware must, by various means, + become aware of all components in the system associated with the boot process + and configure or reset those components into a known state (components include, + for example, buses, bridges, I/O Adapters (IOAs) + See for + the definition of an IOA., + and I/O devices). + + + + + R1--2. + + The firmware must obtain certain system + information which is necessary to build the OF device tree from + “walking” the I/O buses (for example, identification of IOAs and + bridges). + + + +
+ +
+ Generate a Device Tree + + + + R1--1. + + The firmware must build a device tree + and the OS must gain access to the device tree through Client Interface + Services (CIS). + + + + + R1--2. + + Configuration information + (configuration variables) which are stored in non-volatile memory must be + stored under the partition names of-config or + common, depending on the nature of the information (see + ). + + + +
+ +
+ Initialize/Reset System Components + The OS requires devices to be in a known state at the time control + is transferred from the firmware. Firmware may gain control with the hardware + in various states depending on what has initiated the boot process. + + + + Normal boot: Initiated by a power-on sequence; all devices and + registers begin in a hardware reset state. + + + + Reboot: Device state is unpredictable at the start of a + reboot. + + + + The hardware reset state for a device is an inactive state. An + inactive state is defined as a state that allows no system level activity; + there can be no bus activity, interrupt requests, or DMA requests possible from + the IOA that is in a reset state. Since the OS may configure devices in a + manner that requires very specific control over these functions to avoid + transitory resource conflicts, these functions should be disabled at the device + and not at a central controlling agent (for example, the interrupt controller). + Devices that do not share any resources may have these resources disabled at a + system level (for example, keyboard interrupts may be disabled at the interrupt + controller in standard configurations). + + + + R1--1. + + IOAs must adhere to the reset states + given in when control of the system + is passed from firmware to an OS. + + + + IOA Reset States + + + + + + + + + Bus + + + + + IOAs Left Open by OF + + + + + Other IOAs + + + + + + + + PCI + + + Interrupts not active + No outstanding I/O operations + IOA is configured + + + The IOA is inactive: + + I/O access response disabled + Memory access response disabled + PCI master access disabled + Interrupts not active + + IOA is reset (see note) + + + + + System + + + Configured per OF device tree + + Interrupts inactive + DMA inactive + No outstanding I/O operations + + + + The IOA is in hardware reset state (see note) or inactive: + + Interrupts inactive + DMA inactive + + + + + +
+ + + + + R1--2. + + The platform must include the root node + OF device tree property “ibm,pci-full-cfg” with a + value of 1 and configure the configuration registers of all PCI IOAs and + bridges as specified by Requirement . + + + + + R1--3. + + Prior to passing control to the OS, the platform must initialize all processor registers to a value which, if + accessed, will not yield a machine check. + + + + + R1--4. + + Prior to passing control to the OS, the + platform must initialize all registers not visible to the OS to a state that is + consistent with the system view represented by the OF device tree. + + + + + R1--5. + + During boot or reboot operations and + prior to passing control to the OS, the platform must initialize the interrupt + controller. + + + + + R1--6. + + Hardware must provide a mechanism, + callable by software, to hard reset all processors and I/O subsystems in order + to facilitate the implementation of the RTAS system-reboot function. + + + + + Platform Implementation Note: The platform + is required to reset the interrupt controller to avoid inconsistency among the + states of IOAs, the interrupt controller, and software interrupt handler + routines. The reset state is shown in . + Software and Firmware Implementation Note: + The conventional PCI configuration registers are further described in the + and are copied into OF properties described + in the . PCI-X configuration registers + are further described in the . PCI + Express configuration registers are further described in the + . PCI-X IOAs and bridges and PCI Express + IOAs, bridges, and switches are treated the same as conventional PCI IOAs and + bridges for purposes of generation of OF properties. + Software and Firmware Implementation Note: In + reference to Requirement , generally + the initial value of processor registers is contained in the processor binding. + However, some processors have deviations on register usage. Also, since some + register implementation is optional, all processors are not the same. +
+ +
+ Locate an OS Boot Image + The OS boot image is located as described in + . A device and filename can be specified directly + from the command interpreter (the boot command) or OF + will locate the image through an automatic boot process controlled by + configuration variables. Once a boot image is located, the device path is set + in the device tree as the “bootpath” + property of the chosen node. + The devices searched by the automatic boot process are those + contained in the boot-device configuration variable. + Implementations may choose to limit the number of boot device entries that are + searched. The root node device tree property + “ibm,max-boot-devices” communicates the number of + boot-device entries that the platform processes. + If multi-boot (multiple bootable OSs residing on the same platform) is supported, + a configuration variable instructs the firmware to display a multi-boot menu + from which the OS and bootpath are selected. See + for information relating to the multiboot process. + + + + R1--1. + + The platform must supply in the OF root + node the “ibm,max-boot-devices” property. + + + +
+ +
+ Load the Boot Image into Memory + After locating the image, it is loaded into memory at the location + given by a configuration variable or as specified by the OS load image format. +
+ +
+ Boot Process + The boot process is described in . + Steps in the process are reviewed here, but the + authoritative and complete description of the process is included in + . is a + depiction of the boot flow showing the action of the f1, f5, and f6 function + keys. The figure should only be used as an aid in understanding the + requirements for LoPAR systems. +   +
+ Boot Process + + + + + + + + +
+ +
+ The Boot Prompt + + + + R1--1. + + After the banner step of the boot sequence, the platform display must present + a clearly visible graphical or text message (boot prompt), and + must provide a reaction window of at least 3 seconds that prompts the + user to activate various options including the f1, f5, and f6 control keys + detailed in this document. + + + + + R1--2. + + The functions provided by f1, f5 and + f6 described in this chapter must be equivalently provided by the tty numeral + keys 1, 5, and 6, respectively when a serial terminal is attached. + + + + + R1--3. + + The boot prompt must identify the + platform and communicate to the user that there are options that may be invoked + to alter the boot process. + + + +
+ +
+ The Menus + Once the boot prompt is displayed, the System Management Services + (SMS) menu can be invoked. SMS provides a user interface for utilities, + configuration, and the Multiboot Menu (as introduced in + ) for boot/install and the OF command + interpreter. + The Multiboot menu is formatted so that block devices that + currently contain boot information are most easily selected by the user. + Because of the serial nature of byte devices, they should not be opened unless + specifically included in a boot list. The user may also wish to add devices to + the boot-device and/or diag-device configuration variables (boot lists) that + currently do not contain boot information. The Multiboot menu presents these + devices in a secondary manner. + If the Multiboot Menu boot/install option is chosen, OF will + execute the bootinfo.txt<boot-script> of the + selected OS, and if the user elects to make this the default, the + boot-command variable will be set equal to the contents of + bootinfo.txt<boot-script>. + + + + R1--1. + + The SMS menu must provide a means to + display the Multiboot Menu. + + + + + R1--2. + + If, after the boot + prompt is displayed, + auto-boot? = false + and menu? = true, + the firmware must display the Multiboot Menu directly. + + + + + R1--3. + + The Multiboot Menu must present all + potential boot device options, differentiating block devices that contain + locatable bootinfo objects. + + + + + R1--4. + + Firmware must evaluate all + bootinfo objects at each invocation of the Multiboot Menu to ensure + that any modifications made by the OS will be included. + + + + + R1--5. + + The Multiboot Menu must provide a + means to enter the currently selected boot option into the desired location + within the boot-device/boot-file or + diag-device/diag-file configuration variables. + + + + + R1--6. + + The platform must provide a means to + delete individual boot options from the + boot-device/boot-file and + diag-device/diag-file configuration variables. + + + + + R1--7. + + The Multiboot Menu must provide an + option for the user to select whether or not to return to the Multiboot Menu on + each boot. + + + + + Firmware Implementation Note: Returning to the Multiboot Menu on + reboot is controlled with the auto-boot? and + menu? configuration variables. +
+ +
+ The f1 Key + The boot process is further controlled by the + auto-boot? and + menu? + OF configuration variables and the f1 key. + + + + R1--1. + + If, after the boot + prompt is displayed, function key f1 is pushed or if + auto-boot? = false and + menu? = false, the firmware must display the + System Management Services (SMS) menu. + + + + + R1--2. + + The default value for the + auto-boot? configuration variable must be + true. + + + + + R1--3. + + The default value for the + menu? configuration variable must be + false. + + + +
+ +
+ The f5 and f6 Keys + If auto-boot? = true, + the commands specified by the boot-command configuration + variable are executed. + If the boot command has no arguments, IEEE + 1275 states that the arguments are determined as follows: + + + + Normal Boot - If the + diagnostic-mode?FCode + function returns false, the boot + device is given by boot-device and the default boot + arguments are given by boot-file. + + + + Diagnostics Boot - If the diagnostic-mode? + FCode function returns true, the boot device is given by + diag-device and the default boot arguments are given by + diag-file. + + + + Platform Implementation Note: + boot-device, + boot-file, + diag-device and + diag-file + are potentially multi-entry strings. The + boot-command searches the + devices specified in boot-device/diag-device in the order + defined by the string for the boot-file/diag-file to load + into system memory. Failure occurs only if no corresponding file is + found/usable on any of the specified devices. + Platforms give the user the ability to control the boot process + further with function keys f5 and f6 (within the window described in + Requirement ). + + + + R1--1. + + If, after the boot prompt is displayed, function key f5 is pushed (and + auto-boot? = true), then + diagnostic-mode? must return true and the + default diagnostic device as defined in Requirements + and + must be used to locate bootable + media. + + + + + R1--2. + + If, after the boot prompt is displayed, function key f6 is pushed (and + auto-boot? = true), then + diagnostic-mode? must return true and + diag-device must be used to locate the boot image, else + if diag-device is empty, then its default as defined in + Requirements and + must be used to locate bootable + media. + + + + + R1--3. + + boot-command + must default to boot <with no + arguments>. + + + + + R1--4. + + boot-device and + diag-device + must default to the first devices of each type that + would be encountered by a search of the device tree. + + + + + R1--5. + + The search order for the + boot-device and + diag-device + defaults must be floppy, cdrom, tape, disk, network. + + + + + R1--6. + + boot-file must + default to <null>. + + + + + R1--7. + + diag-file must + default to diag. + + + + + Note: Requirement + provides a method to invoke stand-alone + diagnostics or to start reinstallation without going through the menus. + Requirement provides a method to boot + with on-line diagnostics. + Software Implementation Note: Pressing either f5 or f6 at the + correct time will cause the contents of diag-file to be + set into the “bootargs” property of the + chosen node of the device tree. The OS can recognize a + diagnostics boot request when it finds the “diag” + substring in “bootargs”. +
+ +
+ CDROM Boot + If the CDROM is the first bootable media found in the devices + listed in the bootlist (boot-device strings), the CDROM + should boot without having to enter optional file specification information or + using the f5 function key normally used for diagnostic boot. This is + accomplished by having the appropriate bootinfo.txt file + specification in the CDROM entry in the bootlist. + + + + R1--1. + + CDROM entries for the default OF + boot-device and + diag-device + configuration variables must include the standard block device + bootinfo.txt file specification as documented in + (\ppc\bootinfo.txt). + + + +
+ +
+ Tape Boot + Boot from tape is defined in . +
+ +
+ Network Boot + The user selects from a list of network devices on the Multiboot + Menu and then selects the boot option. The user may be prompted for network + parameters (IP addresses, etc.) which are set as arguments in + boot-device by the firmware. If the BOOTP protocol is used, the + BOOTREPLY packet contains the network parameters to be used for subsequent + transmissions (see for details of + this process). + + + + R1--1. + + If network boot is selected, firmware + must provide a means for the user to specify or override network parameters. + + + +
+ +
+ Service Processor Boot + In platforms with a service processor, the user may call for a boot + using a local/remote connection to the service processor. The particular port + used for this remote session is sent to the firmware in a status message after + the service processor finishes POST. The port is identified in the + “stdin” + and “stdout” + properties in the chosen node of the OF device tree. +
+ +
+ Console Selection + During the boot process, firmware establishes the console to be + used for displaying status and menus. The following pseudocode describes the + console selection process: + + + + + R1--1. + + If a console has been selected during + the boot process, firmware must set the “stdin” + and “stdout” properties of the + chosen node to the ihandles of this console’s input and + output devices prior to passing control to the OS. + + + +
+ +
+ Boot Retry + For boot failures related to firmware trying to access a boot + device, it is appropriate for the platform to retry the boot operation, + especially in the case of booting from a network device. However, in platforms + which have a service processor, there are several other types of detected + errors for which a reboot retry may be appropriate; for example, checkstops or + loss of communication between firmware and the service processor. To ensure + that the user policy is followed, the coordination and counting of retry + attempts need to be interlocked between the service processor and boot + firmware. The most straightforward way to implement this is to have the boot + firmware inform the service processor of all failed boot attempts, and let the + service processor initiate the system reset (as it also would for checkstops or + hangs). This way the service processor can easily manage the retry count and + initiate a service dial-out if the boot retry limit is exceeded. + + + + R1--1. + + Platform + Implementation: In platforms with service processors, retry of + failed boot operations must be coordinated between boot firmware and the + service processor, to ensure correct counting and handling of reboot retries + according to the service processor configuration reboot policies. + + + +
+ +
+ Boot Failures + Failure to boot occurs only when no corresponding file is found + which is usable on any device specified in the + boot-device, + boot-file, + diag-device, or + diag-file string being used. + + + + R1--1. + + If an error occurs in a boot device + preventing boot from that device, and after all defined retries have occurred, + the failure must be reported as a POST error. + + + + + R1--2. + + If a boot device is physically + missing or lacks a boot record (for example, if a CDROM is not present in a + CDROM drive), then a POST error must be generated for this case, must not + result in the calling out of a boot device as being defective, and must not + result in a hardware service repair action to the device. + + + + + R1--3. + + In Requirement + , if it is not possible for a device to + distinguish between an actual device error, as opposed to a missing device or + boot record, then a POST error must be generated that indicates the possible + causes of the failure to boot from the device, and this POST error must not + imply that a hardware service repair action is required for the boot + device. + + + + + Implementation Note: All device errors of the + same type may be consolidated into a single POST log entry with multiple + location codes listed if needed. This architecture anticipates remote support + center notification of hardware errors. It is the intention that only + definitive boot device errors will be reported as requiring hardware repair. + This is meant to prevent service calls for systems for non-hardware errors such + as no tape in a tape drive. +
+ +
+ Persistent Memory and Memory Preservation Boot + (Storage Preservation Option) + Selected regions of storage, or Logical Memory Blocks (LMBs), may + be optionally preserved across client program boot cycles. These LMBs are + denoted by the presence of the “ibm,preservable” + property in their OF device tree /memory node. + The client program registers the LMB with + the platform using the ibm,manage-storage-preservation + RTAS call if it wants the contents of the storage preserved across client boot + cycles (see also "Managing Storage Preservations" in + specification). The architectural intent of this + facility is to enable client programs to emulate persistent storage. This is + done by a client program registering preservable LMBs. Then, after a subsequent + boot cycle (perhaps due to error or impending power loss) the presence of the + “ibm,preserved-storage” property in the + /rtas node of the device tree indicates to the client + program that it has preserved memory. When the client program detects that it + has booted with preserved storage and that it might be necessary to preserve + the storage for long term, the client program is responsible for copying the + preserved data to long term persistent storage medium, and then clearing the + registration of the preserved LMBs to prevent potential corruption of the + persistent storage medium due to subsequent failures. + Upon reboot after such an operation, the + “ibm,request-partition-shutdown” property is provided + in the /rtas node with a value of 2, indicating that the + client program should save appropriate data and shutdown the partition. + Implementation Note: How areas get chosen to + be marked as preservable is beyond the scope of this architecture. +
+
+ +
+ +
+ Transfer Phase + The image is prepared for execution by checking it against certain + configuration variables; this may result in a reboot. + Once the OS gains control, it may use the CIS interface to learn + about the platform contents and configuration. The OS will generally build its + own version of this configuration data and may discard the OF code and device + tree in order to reclaim the space used by OF. A set of + platform-specific functions are provided by Run-Time Abstraction Services + (RTAS) which is instantiated by the OS invoking the + instantiate-rtas method of the RTAS OF device tree node. + + + + R1--1. + + If any device tree property is presented + that contains a phandle value to identify a certain node in the device tree, + the device tree node so identified must contain the + “ibm,phandle” property, and the value of the + “ibm,phandle” property must match the + phandle value in the property identifying that node. + + + + + R1--2. + + If the “ibm,phandle” + property is present in a device tree + node, the OS must use this value, and not the phandle value returned by a + client interface service, to associate this node with a device tree property + that uses a phandle value to identify this node. + + + + + R1--3. + + An OS must not assume that the + “ibm,phandle” property, if present, corresponds to the + phandle used by or returned by OF client interface services. A phandle value + passed to a client interface service as an argument must have been obtained by + use of a client interface service, and not from a device tree property + value. + + + + + Note: If the “ibm,phandle” + property exists, there are two “phandle” namespaces which must be kept separate. One is that + actually used by the OF client interface, the other is properties in the device + tree making reference to device tree nodes. These requirements are written to + maintain backward compatibility with older FW versions predating these + requirements; if the “ibm,phandle” property + is not present, the OS may assume that any device tree properties which refer + to this node will have a phandle value matching that returned by client + interface services. It will be necessary to have the OSs ready for this + requirement before the firmware implementation. +
+ +
+ Run-Time + During run-time, the OS has control of the system and will have + RTAS instantiated to provide low-level hardware-specific functions. +
+ +
+ Termination + Termination is the phase during which the OS yields control of the + system and may return control to the firmware depending on the nature of the + terminating condition. + +
+ Power Off + If the user activates the system power switch, power may be removed + from the hardware immediately (switch directly controls the power supply) or + software may be given an opportunity to bring the system down in an orderly + manner (power management control of the power switch). + If power is removed from the hardware immediately, the OS will lose + control of the system in an undetermined state. Any I/O underway will be + involuntarily aborted and there is potential for data loss or system damage. A + shut-down process prior to power removal is highly recommended. + In most power managed systems, power switch activation is fielded + as a power management interrupt and the OS (through RTAS) is able to quiesce + the system before removing power. The OS may turn off system power using the + RTAS power-off function. +
+ +
+ Reboot + The OS may cause the system to reset and reboot by calling the RTAS + system-reboot function. +
+
+ +
+ +
+ Firmware + + + + R1--1. + + Platforms must implement OF as defined in . + + + + + R1--2. + + The OF User Interface must include the + following methods as specified in , + Section 7.6:.registers, + to, + load, + go, + state-valid + and init-program. + + + + + R1--3. + + Platforms must implement the Run-Time Abstraction Services (RTAS) as described in + . + + + + + R1--4. + + OSs must use OF and the RTAS functions to be + compatible with all platforms. + + + +
+ +
+ OS Installation + Installation of OSs will be accomplished through the Multiboot Menu + as follows: + + + + The system boots or reboots normally; the user enters the + Multiboot Menu by one of the methods described herein. + + + + The Multiboot Menu presents a list of all installation + devices. + + + + The user selects “install” and an installation + device from the menu; firmware locates the bootinfo object or install image on + the selected installation device. + + + + Firmware will execute init-program and, if a + bootinfo object was found, firmware parses it, replaces the <boot-script> + entities with appropriate values and executes the script. + + + + The OS gets control and selects the target device. + + + + After the install process is determined to be successful, the OS + updates variables such as boot-device, + boot-file, + and boot-command. + + + + The OS adds the bootinfo-nnnn configuration + variable to the NVRAM common system partition. + + + + + + R1--1. + + The Multiboot Menu must provide an option for + OS installation that lists all possible installation devices. + + + + + R1--2. + + After the install process is determined to be successful, the OS + must set boot-device, + boot-file, + and boot-command. + + + + +
+ Tape Install + The OF definition of installation from tape is defined in + . +
+ +
+ Network Install + Network install follows the same process as network boot with the + exception that after installation is complete, the OS will write + boot-device with the target device information. + + + + R1--1. + + If network install is selected, firmware + must provide a means for the user to override default network parameters. + + + +
+
+ +
+ Diagnostics + IBM Power® system platforms may use IBM AIX® Kernel-based + stand-alone diagnostics as their multi-OS common diagnostics package. Since AIX + will run on other vendors’ platforms which might not have permission to + use AIX diagnostics, the “ibm,aix-diagnostics” + property indicates that AIX diagnostics are permitted (see "Root + Node Properties" in ). + + + + R1--1. + + If AIX diagnostics are supported on a + platform, then the firmware for that platform must include the property + “ibm,aix-diagnostics” in the + root node. + + + + + Software Implementation Note: Each OS may implement an OS-specific + run-time diagnostics package, but should, for purposes of consistency, adhere + to the error log formats in . +
+ +
+ Platform Class + The “ibm,model-class” OF property + is defined to classify platforms for planning, marketing, licensing, and + service purposes (see "Root Node Properties" in + ). + + + + R1--1. + + The “ibm,model-class” + property must be included in the + platform’s root node. + + + +
+ +
+ Security + Platforms will provide the user with options for a Power On Password + (POP) and a Privileged Access Password (PAP) and will have some optional + physical security features. + + + + R1--1. + + Platform + Implementation: Platforms must provide a Power On + Password (POP) capability which, when enforced, controls the + user’s ability to power-on and execute the configured boot + sequence. + + + + + R1--2. + + Platform + Implementation: Platforms must provide a Privileged + Access Password (PAP) capability which, when enforced, controls the + user’s ability to alter the boot sequence using f5/f6, and to enter SMS + and the Multiboot Menu. + + + + + R1--3. + + Platform + Implementation: If the PAP is absent or <NULL>, but the POP is + non-<NULL>, then the POP must act as the PAP. + + + + + R1--4. + + Platform + Implementation: Platforms must accept the PAP as a valid response to + a request to enter the POP. + + + + + R1--5. + + Platform Implementation: If + there is a key switch implemented with a secure position, the + system must not complete the boot process regardless of the state of POP and + PAP when the switch is in this position. + + + + + R1--6. + + Platform + Implementation: If a key switch is implemented and the switch is in + the maintenance (service) position, the POP and PAP must + not be enforced. + + + + + R1--7. + + Platform + Implementation: Platforms, except for rack mounted systems, must + provide a locking mechanism as an option which prevents the removal of the + covers. + + + + + R1--8. + + Platform Implementation: Platforms, except for rack mounted systems, must + provide a tie-down mechanism as an option which prevents the physical removal + of the system from the premises. + + + + + R1--9. + + Platform Implementation: Passwords and keyswitch positions must be + implemented in a manner that makes their values accessible to both OF and the + service processor. + + + + + R1--10. + + Platform Implementation: The OF configuration variable + security-password must be maintained to be equivalent to the + Privileged Access Password (PAP). + + + + + R1--11. + + Platform + Implementation: If the PAP and security-password + are absent or <NULL>, security-mode must be set to + “none”, otherwise security-mode + must be set to “command”. + + + + + R1--12. + + Platform Implementation: If security-mode + is set to any value other than “none” (such as + “command” or “full”), + it must be treated as security-mode=command. + Platform Implementation Notes: + + + + As defined here, the PAP and security-password are + stronger than as specified in IEEE 1275 for + security-mode = command in that + they are required for any command line operations, including + go and + boot. The PAP and + security-password are not required to boot the system with default + parameters, however, and in this sense the intent of + security-mode = command is achieved. There is currently no + implementation of + security-mode = full. + + + + If a service processor is provided, the requirements relating to + passwords are applicable in the service processor environment. Service + processor documentation refers to the POP as the General User Password and the + PAP as the Privileged User Password. + + + + + +
+ +
+ Endian Support + LoPAR platforms operate with either Big-Endian (BE) or Little-Endian + (LE) addressing. In Big-Endian systems, the address of a word in memory is the + address of the most significant byte (the “big” end) of the word. + Increasing memory addresses will approach the least significant byte of the + word. In Little-Endian (LE) addressing, the address of a word in memory is the + address of the least significant byte (the “little” end) of the + word. + All data structures used for communicating between the OS and the + platform (for example, RTAS and hypervisor calls) are Big-Endian format, unless + otherwise designated. + + + + R1--1. + + Platforms must by default operate with Big-Endian addressing. + + + + + R1--2. + + Platforms that operate with Little-Endian addressing must make + System memory appear to be in Little-Endian format to all entities in the + system that may observe that image, including I/O. + + + + + Platform Implementation Notes: + + + + Some hardware (for example, bridges, memory controllers, and + processors) may have modal bits to allow those components to be used in + platforms which operate in Little-Endian mode. In this case, the hardware or + firmware will need to set those bits appropriately. + + + + Requirement may have an + impact on the processor chosen for the platform. + + +
+ +
+ 64-Bit Addressing Support + A 64-bit-addressing-capable platform is defined as one capable of + supporting System Memory and Memory Mapped I/O (MMIO) configured above 4 GB + (greater than 32 bits of real addressing). This means that all hardware + elements in the topology down to the Host Bridges are capable of dealing with a + real address range greater than 32 bits, and all Host Bridges are capable of + providing a translation mechanism for translating 32-bit I/O bus DMA addresses. + All platforms compliant with IBM + Power Architecture Platform Requirements (PAPR) version 2.3 and beyond are required to be + 64-bit-addressing-capable. + A 64-bit-addressing-aware OS is an OS that can deal with a real + address space larger than 4GB. It must handle the 64-bit processor page table + format (required of all OSs), and must understand Host Bridge mechanisms and + Host Bridge OF methods for supporting System Memory greater than 4 GB. All OSs + compliant with IBM + Power Architecture Platform Requirements (PAPR) version 2.3 and beyond are required to be + 64-bit-addressing-aware. +
+ +
+ Minimum System Requirements + This section + summarizes the minimum hardware and functionality required for LoPAR + compliance. + The + term portable is used in this document to describe that class of systems that + is primarily battery powered and is easily carried by its user. + The term personal is used in this document to describe that class of systems that + is bound to a specific work area due to its size or power source, and whose use + is generally restricted to a single direct user or a small set of users. + The term server is used in this document to describe that class of systems that + supports a multi-user environment, providing a particular service such as file + storage, software repository, or remote processing capability. + Each of these classes may have unique requirements due to the way it + is used or which OS it generally employs and, for this reason, the requirements + in this document my have qualifiers based on the type of system being + developed. + + + + R1--1. + + (Requirement moved to + ) + + + + + R1--2. + + A means of attaching a diskette drive must be + provided (may be through a connector or over a network) and the drive must have + the following characteristics: + + + + Media sense: Implementations must allow polling of the drive up to + 100x per second to determine the presence of media in the drive. + + + + Must accept media of type: 3.5" 1.44 MB MFM + + + + + + + + R1--3. + + A means of attaching a CD-ROM drive must be + provided (may be through a connector or over a network) and the drive must have + the following characteristics: + + + + ISO9600 compliant + + + + Supports multi-session + + + + + + + + R1--4. + + When a keyboard is provided, it must be + capable of generating at least 101 scan codes. + + + + + R1--5. + + When a mouse is provided, it must have at + least two buttons. + + + + + R1--6. + + The capability to generate a tone must be provided on portable + and personal platforms, and on server platforms which are not housed in rack + enclosures. + + + + + R1--7. + + A Real Time Clock (RTC) must be + provide which must have the following characteristics: + + + + Is non-volatile + + + + Runs continuously + + + + Has a resolution of at least one second + + + + + + +
+ +
+ Options and Extensions + Options are features that are covered by this architecture, but are + not necessarily required to be present on a given platform. Platforms that + implement options are required to conform to the definitions in this + architecture, so that an aware OS environment can recognize and support them. + Some options may be required on some platforms. Refer to + for the disposition of currently defined + options, including requirements for implementation of some of these options on + some platforms. Note that in this table, “optional” does not mean + “not required;” see the description column of the table for more + information. + An extension is a feature that is added to this architecture and is + required on all platforms developed after a specified effective date. + Options and extensions will normally need to be dormant or invisible + in the presence of a non-aware OS environment. In general, this means that they + come up passively; that is, they are initialized to an inactive state and + activated by an aware OS. + + + + R1--1. + + Extensions and options must come up + passively unless otherwise specified in this architecture. + + + + + R1--2. + + Extensions and options that affect the OS + interface to the platform must be identified, when present, through some + architected means, such as OF device tree properties. + It is the responsibility of the product development teams to keep the + “usage” columns of up + to date, + + + + + + LoPAR Optional Features + + + + + + + + + + Option Name + + + + + Usage + + + + + Description + + + + + + + Base + + + + + IBM Server + + + + + + + Usage Legend : NS = + Not Supported; O = Optional (see also Description); OR = Optional but + Recommended; R = Required; SD = See Description + + + + + + + + Symmetrical Multiprocessing (SMP) + + + O + + + R + + + Required on MP platforms. + + + + + Multiboot + + + O + + + O + + + Required to support multiple versions of an OS. + + + + + PCI Hot Plug DR + + + O + + + OR + + + See for more information. + + + + + Logical Resource Dynamic Reconfiguration (LRDR) + + + O + + + OR + + + . + + + + + Enhanced I/O Error Handling (EEH) + + + OR SD + + + R + + + See and + . Requirements for platforms that implement + LPAR, regardless of the number of partitions, are contained in + . + + + + + Error Injection (ERRINJCT) + + + O + + + R + + + Required of servers which implement the EEH option. + + + + + Logical Partitioning (LPAR) + + + O + + + R + + + See . + + + + + Bridged-I/O EEH Support + + + O + + + R + + + EEH support for I/O structures which contain PCI to PCI + bridges or PCI Express switches. See . + Required if EEH is supported. + + + + + PowerPC External Interrupt + + + R + SD + + + R + SD + + + May be virtualized; See . + + + + + EXTI2C + + + O + + + O + + + See for more information on + support of I2C buses. + + + + + Firmware Assisted NMI (FWNMI) + + + R + + + R + + + . + + + + + System Parameters + + + R + + + R + + + . + + + + + Capacity on Demand (CoD) + + + O + + + O + + + . + + + + + Predictive Failure Sparing + + + O + + + O + + + . + + + + + Converged Location Codes + + + R + + + R + + + The Converged Location Codes option is required on all + platforms being developed. and + Requirement . + + + + + Shared Processor LPAR (SPLPAR) + + + O + + + O + + + . + + + + + Reliable Command/Response Transport + + + O + + + O + + + . + + + + + Logical Remote DMA (LRDMA) + + + O + + + O + + + . + + + + + Interpartition Logical LAN (ILLAN) + + + O + + + O + + + . + + + + + ILLAN Backup Trunk Adapter + + + O + + + O + + + . + + + + + ILLAN Checksum Offload Support + + + O + + + O + + + . + + + + + Checksum Offload Padded Packet Support + + + O + + + O + + + See . + + + + + Virtual SCSI (VSCSI) + + + O + + + O + + + . + + + + + Virtual FC (VFC) + + + O + + + O + + + See . + + + + + Storage Preservation + + + O + + + NS + + + and "Managing + Storage Preservations" in specification. + + + + + Client Vterm + + + O + + + R + + + Required of all platforms that support LPAR, otherwise not + implemented. Provides a virtual “Asynchronous” IOA for connecting + to a server Vterm IOA, the hypervisor, or HMC (for example, to a virtual + console). See for more + information. + + + + + Server Vterm + + + O + + + O + + + Allows a partition to serve a partner partition's client + Vterm IOA. + + + + + NUMA + Associativity Information + + + OR + + + OR + + + See . + + + + + Performance Tool Support + + + O + + + NS + + + Provides access to platform-level facilities for + performance tools running in a partition on an LPAR system. See + . + + + + + MSI (Message Signaled Interrupt) + + + SD + + + SD + + + Required for all platforms that support PCI Express. + + + + + ILLAN Buffer Size Control + + + O + + + O + + + See . + + + + + Virtual Management Channel (VMC) + + + O + + + O + + + See . + + + + + Partition Suspension + + + O + + + O + + + Requires the Logical Partitioning, LRDR, and Update OF Tree options. + + + + + Partition Hibernation + + + O + + + O + + + Allows a partition to sleep for an extended period; during + this time the partition state is stored on secondary storage for later + restoration. Requires the Partition Suspension, ILLAN, and VASI options. + + + + + Partition Migration + + + O + + + O + + + Allows the movement of a logical partition from one + platform to another; the source and destination platforms cooperate to minimize + the time that the partition is non-responsive. Requires the Partition + Suspension, ILLAN, and VASI options. + + + + + Thread Join + + + O + + + O + + + Allows the multi-threaded caller to efficiently establish + a single threaded processing environment. + + + + + Update OF Tree + + + O + + + O + + + Allows the caller to determine which device tree nodes + changed due to a massive platform reconfiguration as happens during a partition + migration or hibernation. + + + + + Virtual + Asynchronous Services Interface (VASI) + + + O + + + O + + + Allows an authorized virtual server partition (VSP) to + safely access the internal state of a specific partition. See + for more details. Requires the Reliable + Command/Response Transport option. + + + + + Virtualized Real Mode Area (VRMA) + + + O + + + O + + + Allows the OS to dynamically relocate, expand, and shrink + the Real Mode Area. + + + + + TC + + + O + + + O + + + Allows the OS to indicate that there is no need to search + secondary page table entry groups to determine a page table search has failed. + See for more details. + + + + + Configure Platform Assisted Kernel Dump + + + O + + + O + + + Allows the OS to register and unregister kernel dump + information with the platform. + + + + + I/O Super Page + + + O + + + OR + + + Allows the OS to specify I/O pages that are greater than 4 KB in length. + + + + + Subordinate CRQ (Sub-CRQ) Transport + + + O + + + O + + + Support for the Subordinate CRQs as needed by some Virtual + IOAs. See . + + + + + Cooperative Memory Over-commitment (CMO) + + + O + + + O + + + The CMO option allows for partition participation in the + over-commitment of logical memory by the platform. See + . + + + + + Partition Energy Management (PEM) + + + O + + + O + + + Allows the OS to cooperate with platform energy + management. See . + + + + + Multi-TCE-Table (MTT) + + + O + + + O + + + Support for the Multi-TCE-Table Option. See + . + + + + + Virtual Processor Home Node (VPNH) + + + O + + + O + + + Provides substantially consistent virtual processor + associativity in a shared processor LPAR environment. See + . + + + + + IBM Active Memory™ Compression + + + O + + + O + + + Allows the partition to perform active memory compression. + + + + + Virtual Network Interface Controller (VNIC) + + + O + + + O + + + See . + + + + + Expropriation Subvention Notification + + + O + + + O + + + Allows OS notification of a cooperative memory + overcommitment page fault see . + + + + + Boost Modes + + + O + + + O + + + Allows the platform to communicate and the availability of + performance boost modes along with any ability to manage the same. See + + + + + + Platform Resource Reassignment + Notification (PRRN) + + + O + + + O + + + + + + + + + + Dynamic DMA Windows (DDW) + + + O + + + O + + + Allows the creation of DMA Windows above 4 GB. See + . + + + + + Universally Unique Partition Identification Option (UUID) + + + O + + + O + + + + + + + + + + Platform Facilities Option (PFO) + + + O + + + O + + + See for more information. + + + + + Extended Cooperative Memory Overcommittment (XCMO) + + + O + + + O + + + Introduces additional cooperative memory overcommitment + functions see + + + + +
+
+ +
+ IBM LoPAR Platform Implementation Requirements + The tables in this section detail specific product requirements which + are not defined as an “option” in this architecture. The intent + is to define base requirements for these products, over and beyond what is + specified in and elsewhere in this + architecture. + In addition, any options that are unique to specific implementations + (that is, not general usage), and which do not appear in + , are listed in this section. + It is the responsibility of the product development teams to keep + these tables up to date. + +
+ IBM Server Requirements + This section talks to the requirements for IBM LoPAR Compliant + server platforms. + + + + R1--1. + + For all IBM LoPAR Compliant + Platforms: The platform must implement the options marked as + “required” in the IBM Server column of + and the additional functions as indicated + in (that is, the “Base” + column of is not sufficient). + + + + + + IBM Server Required Functions and Features + + + + + + + + + Function/Feature + + + + + Effective Date + + + + + Description + + + + + + + + All IOA device drivers EEH enabled or EEH safe + + + 6/2004 + + + Required even for systems running with just one partition. + + + + +
+ It is the responsibility of the product development teams to keep + up to date. +
+
+ +
+ Behavior for Optional and Reserved Bits and Bytes + Behavior of the OSs and platforms for bits and bytes in this + architecture that are marked as reserved or optional are defined here. + + + + R1--1. + + Bits and bytes which are marked as + “optional” by this architecture and which are not implemented by + the platform must be ignored by the platform on a Store + and must be returned as 0’s on a Load, including + the reserved or optional bits of a partially implemented field. + + + + + R1--2. + + Bits and bytes which are marked as + “reserved” by this architecture must be ignored by the platform + on a Store and must be returned as 0’s on a + Load, except that bits that are marked as + “reserved” and which were previously defined by the architecture + maybe be treated appropriately by legacy hardware (such bits in this + architecture will state the value that software must use henceforth). + + + + + R1--3. + + Bits and bytes marked as + “reserved” must be set to 0 by the OS on a + Store, except as otherwise defined by the architecture, and must be + ignored on a Load. + + + +
+ + diff --git a/Platform/figures/PAPR-10.gif b/Platform/figures/PAPR-10.gif new file mode 100644 index 0000000..7b9de73 Binary files /dev/null and b/Platform/figures/PAPR-10.gif differ diff --git a/Platform/figures/PAPR-11.gif b/Platform/figures/PAPR-11.gif new file mode 100644 index 0000000..2673bcd Binary files /dev/null and b/Platform/figures/PAPR-11.gif differ diff --git a/Platform/figures/PAPR-12.gif b/Platform/figures/PAPR-12.gif new file mode 100644 index 0000000..b9f6282 Binary files /dev/null and b/Platform/figures/PAPR-12.gif differ diff --git a/Platform/figures/PAPR-14.gif b/Platform/figures/PAPR-14.gif new file mode 100644 index 0000000..7a65a00 Binary files /dev/null and b/Platform/figures/PAPR-14.gif differ diff --git a/Platform/figures/PAPR-15.gif b/Platform/figures/PAPR-15.gif new file mode 100644 index 0000000..159b854 Binary files /dev/null and b/Platform/figures/PAPR-15.gif differ diff --git a/Platform/figures/PAPR-3.gif b/Platform/figures/PAPR-3.gif new file mode 100644 index 0000000..a9bec68 Binary files /dev/null and b/Platform/figures/PAPR-3.gif differ diff --git a/Platform/figures/PAPR-32.gif b/Platform/figures/PAPR-32.gif new file mode 100644 index 0000000..b188589 Binary files /dev/null and b/Platform/figures/PAPR-32.gif differ diff --git a/Platform/figures/PAPR-4.gif b/Platform/figures/PAPR-4.gif new file mode 100644 index 0000000..b5bd401 Binary files /dev/null and b/Platform/figures/PAPR-4.gif differ diff --git a/Platform/figures/PAPR-6.gif b/Platform/figures/PAPR-6.gif new file mode 100644 index 0000000..64e166a Binary files /dev/null and b/Platform/figures/PAPR-6.gif differ diff --git a/Platform/figures/PAPR-7.gif b/Platform/figures/PAPR-7.gif new file mode 100644 index 0000000..c030e29 Binary files /dev/null and b/Platform/figures/PAPR-7.gif differ diff --git a/Platform/figures/PAPR-8.gif b/Platform/figures/PAPR-8.gif new file mode 100644 index 0000000..65df618 Binary files /dev/null and b/Platform/figures/PAPR-8.gif differ diff --git a/Platform/pom.xml b/Platform/pom.xml new file mode 100644 index 0000000..da1ba91 --- /dev/null +++ b/Platform/pom.xml @@ -0,0 +1,148 @@ + + + + + org.openpowerfoundation.docs + workgroup-pom + 1.0.0-SNAPSHOT + ../pom.xml + + 4.0.0 + + + LoPAR-Platform + + jar + + + LoPAR-Platform + + + + + 0 + + + + + + + + + org.openpowerfoundation.docs + + openpowerdocs-maven-plugin + + + + generate-webhelp + + generate-webhelp + + generate-sources + + + ${comments.enabled} + LoPAR-Platform + 1 + UA-17511903-1 + + appendix toc,title + article/appendix nop + article toc,title + book toc,title,figure,table,example,equation + book/appendix nop + book/chapter nop + chapter toc,title + chapter/section nop + section toc + part toc,title + qandadiv toc + qandaset toc + reference toc,title + set toc,title + + + 1 + 3 + 1 + + + LoPAR_Platform + + + LoPAR_Platform + + + + workgroupSpecification + + + + + workgroupConfidential + + + + + draft + + + + + + + + + true + . + + + bk_main.xml + + + + + ${basedir}/../glossary/glossary-terms.xml + 1 + www.openpowerfoundation.org + + + + + + diff --git a/README.md b/README.md new file mode 100644 index 0000000..2905127 --- /dev/null +++ b/README.md @@ -0,0 +1,105 @@ +# Linux Architecture Reference Specification for OpenPOWER +This repository hold the source for the source for the +Linux on Power Architecture Reference documents. There are +multiple component documents as follows: + +* The Platform (../Platform/) document describes the basic +requirements to run Linux on the hardware platform. + +* The Device Tree (../DeviceTree/) document describes the +structure and bindings associated with the device tree +definitions for OpenPOWER systems. + +* The Error Handing (../ErrorHandling/) document describes +the error reporting and recommended error procedures for the system. + +* The run-time services or RTAS (../RTAS/) document describes +the firmware interfaces available to Linux running on the system +and in a VM. + +* The Virtualization (../Virtualization/) document describes the +environment by which virtualized OS images are run on the system. + +The basis for this document was the +[*Linux on Power Architecture Platform Reference (LoPAR)*](https://openpowerfoundation.org/?resource_lib=linux-on-power-architecture-platform-reference) +Version 1.1, March 2016. It was derived from an IBM document known as the *Power Architecture Platform Reference (PAPR)* Versions 2.7. While much of this +documentation may apply to the IBM PowerVM (LPAR) environment, it will serve as a good base for the OpenPOWER documentation effort as well as support the +more broad IBM Linux on Power community as well. + +To build this project, one must ensure that the Docs-Master project has +also been cloned at the same directory level as the Docs-Template project. +This can be accomplished with the following steps: + +1. Clone the master documentation project (Docs-Master) using the following command: + + ``` + $ git clone https://github.com/OpenPOWERFoundation/Docs-Master.git + ``` + +2. Clone this project (Docs-Template) using the following command: + + ``` + $ git clone https://github.com/OpenPOWERFoundation/Linux-Architecture-Reference.git + ``` + +3. Build the project with these commands: + ``` + $ cd Linux-Architecture-Reference + $ mvn clean generate-sources + ``` + +The online version of the document can be found in the OpenPOWER Foundation +Document library at [TBD](http://openpowerfoundation.org/?resource_lib=tbd) + + +## Contributions +To contribute to the OpenPOWER Foundation template document project, contact Jeff Scheel \([scheel@us.ibm.com](mailto://scheel@us.ibm.com)\) or +Jeff Brown \([jeffdb@us.ibm.com](mailto://jeffdb@us.ibm.com)\). + +Contributions to this project should conform to the `Developer Certificate +of Origin` as defined at http://elinux.org/Developer_Certificate_Of_Origin. +Commits to this project need to contain the following line to indicate +the submitter accepts the DCO: +``` +Signed-off-by: Your Name +``` +By contributing in this way, you agree to the terms as follows: +``` +Developer Certificate of Origin +Version 1.1 + +Copyright (C) 2004, 2006 The Linux Foundation and its contributors. +660 York Street, Suite 102, +San Francisco, CA 94110 USA + +Everyone is permitted to copy and distribute verbatim copies of this +license document, but changing it is not allowed. + + +Developer's Certificate of Origin 1.1 + +By making a contribution to this project, I certify that: + +(a) The contribution was created in whole or in part by me and I + have the right to submit it under the open source license + indicated in the file; or + +(b) The contribution is based upon previous work that, to the best + of my knowledge, is covered under an appropriate open source + license and I have the right under that license to submit that + work with modifications, whether created in whole or in part + by me, under the same open source license (unless I am + permitted to submit under a different license), as indicated + in the file; or + +(c) The contribution was provided directly to me by some other + person who certified (a), (b) or (c) and I have not modified + it. + +(d) I understand and agree that this project and the contribution + are public and that a record of the contribution (including all + personal information I submit with it, including my sign-off) is + maintained indefinitely and may be redistributed consistent with + this project or the open source license(s) involved. +``` + diff --git a/RTAS/app_bibliography.xml b/RTAS/app_bibliography.xml new file mode 100644 index 0000000..0c73bb3 --- /dev/null +++ b/RTAS/app_bibliography.xml @@ -0,0 +1,284 @@ + + + + + Bibliography + This section lists documents which were referenced in this specification or which provide + additional information, and some useful information for obtaining these documents. Referenced + documents are listed below. When any of the following standards are superseded by an approved + revision, the revision shall apply. + + + + + + Linux on Power Architecture Reference: Platform and Device Tree + + + + + Linux on Power Architecture Reference: Device Tree + + + + + Linux on Power Architecture Reference: Error Recovery and Logging + + + + + Linux on Power Architecture Reference: Virtualization + + + + + + + Power ISA + + + + + IEEE 1275, IEEE Standard for Boot (Initialization Configuration) Firmware: + Core Requirements and Practices + IEEE part number DS02683, ISBN 1-55937-426-8 + + + + + Core Errata, IEEE P1275.7/D4 + + + + + Open Firmware Recommended Practice:OBP-TFTP + Extension + + + + + Open Firmware Recommended Practice: Device + Support Extensions + + + + + PCI Bus binding to: IEEE Std 1275-1994, Standard + for Boot (Initialization, Configuration) Firmware + + + + + Open Firmware: Recommended Practice - Interrupt + Mapping + + + + + Open Firmware: Recommended Practice - Forth Source + and FCode Image Support, Version 1.0 + + + + + Open Firmware: Recommended Practice - Interrupt + Mapping, Version 1.0 + + + + + Open Firmware: Recommended Practice - TFTP Booting + Extensions, Version 0.8 + + + + + Open Firmware: Recommended Practice - + Interposition, Version 0.2 + + + + + MS-DOS Programmer's Reference + Published by Microsoft + + + + + Peering Inside the PE: A Tour of the Win32 Portable + Executable File Format + Found in the March, 1994 issue of Microsoft Systems Journal + + + + + ISO-9660, Information processing -- Volume and + file structure of CD-ROM for information interchange + Published by International Organization for Standardization + + + + + System V Application Binary Interface, PowerPC + Processor Supplement + By Sunsoft + + + + + ISO Standard 8879:1986, Information Processing + -- Text and Office Systems -- Standard Generalized Markup Language (SGML) + + + + + IEEE 996, A Standard for an Extended Personal Computer + Back Plane Bus + + + + + PCI Local Bus Specification + All designers are responsible for assuring that they use the most current version of this document + at the time that they design conventional PCI related components or platforms. See the PCI SIG website + for the most current version of this document. + + + + + PCI-to-PCI Bridge Architecture Specification + All designers are responsible for assuring that they use the most current version of this document + at the time that they design conventional PCI related components or platforms. See the + PCI SIG website for the most current version of this document. + + + + + PCI Standard Hot-Plug Controller and Subsystem + Specification + + + + + PCI-X Protocol Addendum to the PCI Local Bus Specification + All designers are responsible for assuring that they use the most current version of this document at + the time that they design PCI-X related components or platforms. See the PCI SIG website for the most + current version of this document. + + + + + PCI Express Base Specification + All designers are responsible for assuring that they use the most current version of this document + at the time that they design PCI Express related components or platforms. See the PCI SIG website for + the most current version of this document. + + + + + PCI Express to PCI/PCI-X Bridge Specification + All designers are responsible for assuring that they use the most current version of this document at the + time that they design PCI Express related components or platforms. See the PCI SIG website for the most current + version of this document. + + + + + System Management BIOS (SMBIOS) Reference + Specification + + + + + (List Number Reserved for Compatibility) + + + + (List Number Reserved for Compatibility) + + + + (List Number Reserved for Compatibility) + + + + + IBM RS/6000® Division, Product Topology Data System, + Product Development Guide + Version 2.1 + + + + + Single Root I/O Virtualization and Sharing Specification + All designers are responsible for assuring that they use the most current version of this document at + the time that they design PCI Express SR-IOV related components or platforms. See the PCI SIG website + for the most current version of this document. + + + + + Multi-Root I/O Virtualization and Sharing Specification + All designers are responsible for assuring that they use the most current version of this document at the + time that they design PCI Express MR-IOV related components or platforms. See the PCI SIG website for the + most current version of this document. + + + + + + diff --git a/RTAS/app_glossary.xml b/RTAS/app_glossary.xml new file mode 100644 index 0000000..a8b2d24 --- /dev/null +++ b/RTAS/app_glossary.xml @@ -0,0 +1,1290 @@ + + + + + Glossary + This glossary contains an alphabetical list of terms, phrases, and abbreviations used in this document. + + + + Term + Definition + + + + AC + Alternating current + + + + ACR + Architecture Change Request + + + + AD + Address Data line + + + + Adapter + A device which attaches a device to a bus or which converts one + bus to another; for example, an I/O Adapter (IOA), a PCI Host Bridge (PHB), + or a NUMA fabric attachment device. + + + + + addr + Address + + + + Architecture + The hardware/software interface definition or software module to + software module interface definition. + + + + ASCII + American National Standards Code for Information + Interchange + + + + ASR + Address Space Register + + + + BAT + Block Address Translation + + + + BE + Big-Endian or Branch Trace Enable bit in the + MSR (MSRBE) + + + + BIO + Bottom of Peripheral Input/Output Space + + + + BIOS + Basic Input/Output system + + + + BIST + Built in Self Test + + + + Boundedly undefined + Describes some addresses and registers which when referenced provide + one of a small set of predefined results. + + + + BPA + Bulk Power Assembly. Refers to components used for power distribution + from a central point in the rack. + + + + BPM + Bottom of Peripheral Memory + + + + BSCA + Bottom of System Control Area + + + + BSM + Bottom of System Memory + + + + BUID + Bus Unit Identifier. The high-order part of an interrupt source number + which is used for hardware routing purposes by the platform. + + + + CCIN + Custom Card Identification Number + + + + CD-ROM + Compact Disk Read-Only Memory + + + + CIS + Client Interface Service + + + + CMO + Cooperative Memory Over-commitment option. See + for more information. + + + + + + CMOS + Complimentary Metal Oxide Semiconductor + + + + Conventional PCI + Behavior or features that conform to . + + + + CPU + Central Processing Unit + + + + CR + Condition Register + + + + CTR + Count Register + + + + DABR + Data Address Breakpoint Register + + + + DAR + Data Address Register + + + + DASD + Direct Access Storage Device (a synonym for “hard disk”) + + + + DBAT + Data Block Address Translation + + + + DC + Direct current + + + + DEC + Decrementer + + + + DIMM + Dual In-line Memory Module + + + + DMA + Direct Memory Access + + + + DMA Read + A data transfer from System Memory to I/O. A DMA Read Request + is the inbound operation and the DMA Read Reply (or Read Completion) is the + outbound data coming back from a DMA Read Request. + + + + DMA Write + A data transfer to System Memory from I/O or a Message Signalled Interrupt (MSI) DMA Write. This is an inbound operation. + + + + DOS + Disk OS + + + + DR + Data Relocate bit in MSR (MSRDR) + + + + DRA + Deviation Risk Assessment + + + + DRAM + Dynamic Random Access Memory + + + + DRC + Delayed Read Completion. A transaction that has completed + on the destination bus and is now moving toward the originating bus to complete. + DR Connector. + + + + DR entity + An entity that can participate in DR operations. That is, an entity + that can be added or removed from the platform while the platform power is on and the + system remains operational. + + + + DRR + Delayed Read Request. A transaction that must complete on the destination bus before completing on the originating bus. + + + + DSISR + Data Storage Interrupt Status Register + + + + DWR + Delayed Write Request. A transaction that must complete on the destination bus before completing on the originating bus. + + + + EA + Effective Address + + + + EAR + External Access Register + + + + ECC + Error Checking and Correction + + + + EE + External interrupt Enable bit in the MSR (MSREE) + + + + EEH + Enhance I/O Error Handling + + + + EEPROM + Electrically Erasable Programmable Read Only Memory + + + + EPOW + Environment and Power Warning + + + + + Error Log indicator An amber indicator that indicates that the user needs to + look at the error log or problem determination procedures, in order to determine the cause. + Previously called System Information (Attention). + + + + FCode + A computer programming language defined by the OF standard which is semantically + similar to the Forth programming language, but is encoded as a sequence of binary byte codes + representing a defined set of Forth words. + + + + FE0 + Floating-point Exception mode 0 bit in the MSR (MSRFE0) + + + + FE1 + Floating-point Exception mode 1bit in the MSR (MSRFE1) + + + + FIR + Fault Isolation Registers + + + + FLR + Function Level Reset (see PCI Express documentation). An optional reset for PCI Express + functions that allows resetting a single function of a multi-function IOA. + + + + FP + Floating-Point available bit in the MSR (MSRFP) + + + + FPSCR + Floating-Point Status And Control Register + + + + FRU + Field Replaceable Unit + + + + FSM + Finite State Machine + + + + GB + Gigabytes - as used in this document it is 2 raised to the power of 30 + + + + HB + Host Bridge + + + + HMC + Hardware Management Console - used generically to refer to the system + component that performs platform administration function where ever physically located. + The HMC is outside of this architecture and may be implemented in multiple ways. + Examples include: a special HMC applications in another system, an external appliance, + or in an LPAR partition using the Virtual Management Channel (VMC) interface to the + hypervisor. + + + + Hz + Hertz + + + + IBAT + Instruction block address translation + + + + ID + Identification + + + + IDE + Integrated Device Electronics + + + + IDU + Interrupt Delivery Unit + + + + IEEE + Institute of Electrical and Electronics Engineers + + + + I2C + Inter Integrated-circuit Communications + + + + I/O + nput/Output + + + + I/O bus master + Any entity other than a processor, cache, + memory controller, or host bridge which supplies both address and data in + write transactions or supplies the address and is the sink for the data in + read transactions. + + + + I/O device + Generally refers to any entity that is connected + to an IOA (usually through a cable), but in some cases may refer to the IOA + itself (that is, a device in the device tree that happens to be used for I/O + operations). + + + + I/O Drawer + An enclosure in a rack that holds at least one PHB and at + least one IOA. + + + + ILE + Interrupt Little-Endian bit in MSR (MSRILE) + + + + Instr + Instruction + + + + Interrupt Number + See Interrupt Vector below. + + + + Interrupt Vector + The identifier associated with a specific interrupt source. + The identifier’s value is loaded into the source’s Interrupt Vector Register and + is read from the Interrupt Delivery Unit’s Interrupt Acknowledge Register. + + + + IOA + I/O Adapter. A device which attaches to a physical bus which is capable + of supporting I/O (a physical IOA) or logical bus (a virtual IOA). The term “IOA” + without the usage of the qualifier “physical” or “virtual” will be + used to designate a physical IOA. Virtual IOAs are defined further in + + . + In PCI terms, an IOA may be defined by a unique combination of its assigned + bus number and device number, but not necessarily including its function number. + That is, an IOA may be a single or multi-function device, unless otherwise specified by + the context of the text. In the context of a PCIe I/O Virtualized (IOV) device (not to be + confused with a virtual IOA), an IOA is a single or multiple function device (for example, a + PCIe Virtual Function (VF) or multiple VFs). An IOA function may or may not have its own set of + resources, that is may or may not be in its own Partitionable Endpoint (PE) domain + (see also + + ). + + + + + IOA function + That part of an IOA that deals with a specific part of the + IOA as defined by the configuration space “Function” part of Bus/Device/Function. + For single-function IOAs, the IOA Function and the IOA are synonymous. + + + + IP + Interrupt Prefix bit in MSR (MSRIP) + + + + IPI + Interprocessor Interrupt + + + + IR + Instruction Relocate bit in MSR register (MSR IR) or infrared + + + + ISF + Interrupt 64-bit processor mode bit in the MSR (MSRISF) + + + + ISO + International Standards Organization + + + + ISR + Interrupt Source Register + + + + ISU + Interrupt Source Unit + + + + KB + Kilobytes - as used in this document it is 2 raised to the power of 10 + + + + KHz + Kilo Hertz + + + + LAN + Local Area Network + + + + LCD + Liquid Crystal Display + + + + LE + Little-Endian bit in MSR (MSRLE) or Little-Endian + + + + LED + Light Emitting Diode + + + + LMB + Logical Memory Block. The Block of logical memory addresses associated with a dynamically + reconfigurable memory node. + + + + Load + A Load Request is the outbound (from the processor) operation + and the Load Reply is the inbound data coming back from a + Load Request. When it relates to I/O operations, this is an + MMIO Load . + + + + LR + Link Register + + + + LSb + Least Significant bit + + + + LSB + Least Significant Byte + + + + LSI + Level Sensitive Interrupt + + + + LUN + Logical Unit Number + + + + L1 + Primary cache + + + + L2 + Secondary cache + + + + MB + Megabytes - as used in this document it is 2 raised to the power of 20 + + + + ME + Machine check Enable + + + + MMIO + Memory Mapped I/O. This refers to the mapping of the address space required + by an I/O device for Load or Store operations into + the system’s address space. + + + + MES + Miscellaneous Equipment Specification + + + + MFM + Modified frequency modulation + + + + MHz + Mega Hertz + + + + MOD + Address modification bit in the MSR + (MSRMOD) + + + + MP + Multiprocessor + + + + MSb + Most Significant bit + + + + MSB + Most Significant Byte + + + + MSI + Message Signalled Interrupt + + + + MSR + Machine State Register + + + + MTT + Multi-TCE-Table option. See + + + . + + + + + N/A + Not Applicable + + + + Nibble + Refers to the first or last four bits in an 8 bit byte + + + + NUMA + Non-Uniform Memory Access + + + + NUMA fabric + Mechanism and method for connecting the multiple nodes of a NUMA system + + + + NVRAM + Nonvolatile Random Access Memory + + + + OF + Open Firmware + + + + OP + Operator + + + + OS + Operating System + + + + OUI + Organizationally Unique Identifier + + + + PA + Processor Architecture + + + + PAP + Privileged Access Password + + + + LoPAR + Used within the Linux on Power Architecture + Reference documents to denote: (1) the architectural requirements specified + by the Linux on Power Architecture Reference document, (2) the Linux on Power Architecture + Reference documents themself, and (3) as an adjective to qualify an entity as being + related to this architecture. + + + + Partitionable Endpoint + This refers to the I/O granule that may be treated as one for + purposes of assignment to an OS (for example, to an LPAR partition). May be an + I/O adapter (IOA), or groups of IOAs and bridges, or portions of IOAs. PE granularity + supported by the hardware may be finer than is supported by the firmware. Grouping + of multiple PEs into one DR entity may limit assignment of a the separate PEs to different + LPAR partitions. See also DR entity. + + + + PC + Personal Computer + + + + PCI + Peripheral Component Interconnect. An all-encompassing term referring to + conventional PCI, PCI-X, and PCI Express. + + + + PCI bus + A general term referring to either the PCI Local Bus, as + specified in and + for conventional PCI and PCI-X, or a PCI Express link, as specified in + for PCI Express. + + + + PCI Express + Behavior or features that conform to + . + + + + PCI link + A PCI Express link, as specified in . + + + + PCI-X + Behavior or features that conform to . + + + + PD + Presence Detect + + + + PE + When referring to the body of the LoPAR, this refers to a Partitionable + Endpoint. + + + + + + + PEM + Partition Energy Management option. See + + + . + + + + + Peripheral I/O Space + The range of real addresses which are assigned + to the I/O Space of a Host Bridge (HB) and which are sufficient to contain all of + the Load and Store address space requirements of all the devices in the I/O Space + of the I/O bus that is generated by the HB. A keyboard controller is an example of + a device which may require Peripheral I/O Space addresses. + + + + Peripheral Memory Space + The range of real addresses which are assigned to the Memory + Space of a Host Bridge (HB) and which are sufficient to contain all of the Load and + Store address space requirements of the devices in the Memory Space of the I/O bus + that is generated by the HB. The frame buffer of a graphics adapter is an example + of a device which may require Peripheral Memory Space addresses. + + + + Peripheral Space + Refers to the physical address space which may + be accessed by a processor, but which is controlled by a host bridge. At least one + peripheral space must be present and it is referred to by the suffix 0. A host bridge + will typically provide access to at least a memory space and possibly to an I/O + space. + + + + PHB + PCI Host Bridge + + + + PIC + Programmable Interrupt Controller + + + + PIR + Processor Identification Register + + + + Platform + Refers to the hardware plus firmware portion of a system composed of hardware, + firmware, and OS. + + + + Platform firmware + Refers to all firmware on a system including the software or firmware in a + support processor. + + + + Plug-in I/O card + A card which can be plugged into an I/O + connector in a platform and which contains one or more IOAs and potentially + one or more I/O bridges or switches. + + + + Plug-in Card + An entity that plugs into a physical slot. + + + + PMW + Posted memory write. A transaction that has complete on the + originating bus before completing on the destination bus + + + + PnP + Plug and Play + + + + POP + Power On Password + + + + POST + Power-On Self Test + + + + PR + Privileged bit in the MSR (MSRPR) + + + + Processor Architecture + Used throughout this document to + mean compliance with the requirements specified in + . + + + + Processor revision number + A 16-bit number that distinguishes between various releases + of a particular processor version, for example different engineering change + levels. + + + + PVN + Processor Version Number. Uniquely determines the particular + processor and PA version. + + + + PVR + Processor Version Register. A register in each processor + that identifies its type. The contents of the PVR include the processor + version number and processor revision number. + + + + RAID + Redundant Array of Independent Disks + + + + RAM + Random Access Memory + + + + RAS + Reliability, Availability, and Serviceability + + + + Real address + A real address results from doing address + translation on an effective address when address translation is enabled. + If address translation is not enabled, the real address is the same as the + effective address. An attempt to fetch from, load from, or store to a real + address that is not physically present in the machine may result in a + machine check interrupt. + + + + Reserved + The term “reserved” is used within this + document to refer to bits in registers or areas in the address space + which should not be referenced by software except as described in this + document. + + + + Reserved for firmware use + Refers to a given location or bit which may not be used by + software, but are used by firmware. + + + + Reserved for future use + Refers to areas of address space or bits in registers which may be + used by future versions of this architecture. + + + + RI + Recoverable interrupt bit in the MSR (MSRRI) + + + + RISC + Reduced Instruction Set Computing + + + + RMA + Real Mode Area. The first block of logical memory addresses + owned by a logical partition, containing the storage that may be accessed with + translate off. + + + + ROM + Read Only Memory + + + + Root Complex + A PCI Express root complex as specified in + . + + + + RPN + Real Page Number + + + + RTAS + Run-Time Abstraction Services + + + + RTC + Real Time Clock + + + + SAE + Log Service Action Event log + + + + SCC + Serial Communications Controller + + + + SCSI + Small Computer System Interface + + + + SE + Single-step trace enabled bit in the MSR + (MSRSE) + + + + Service Focal Point + The common point of control in the system for handling all + service actions + + + + Serviceable Event + Serviceable Events are platform, + global, regional and local error events that require a service action + and possibly a call home when the serviceable event must be handled by a + service representative or at least reported to the service provider. + Activation of the Error Log indicator notifies the customer of the event + and the event indicates to the customer that there must be some intervention + to rectify the problem. The intervention may be a service action that the + customer can perform or it may require a service provider. + + + + SES + Storage Enclosure Services (can also mean SCSI Enclosure + Services in relation to SCSI storage) + + + + SF + Processor 32-bit or 64-bit processor mode bit in the MSR + (MSRSF) + + + + SFP + Service Focal Point + + + + Shrink-wrap OS + A single version of an OS that runs on all + compliant platforms. + + + + Shrink-wrap Application + A single version of an application program + that runs on all compliant platforms with the applicable OS. + + + + SMP + Symmetric multiprocessor + + + + SMS + System Management Services + + + + Snarf + An industry colloquialism for cache-to-cache + transfer. A typical scenario is as follows: (1) cache miss from cache A, + (2) line found modified in cache B, (3) cache B performs castout of modified + line, and (4) cache A allocates the modified line as it is being written back + to memory. + + + + Snoop + The act of interrogating a cache for the presence of a + line, usually in response to another party on a shared bus attempting to + allocate that line. + + + + SPRG + Special Purpose Registers for General use + + + + SR + System Registers + + + + SRC + Service Reference Code + + + + SRN + Service Request Number + + + + Store + A Store Request is an + outbound (from the processor) operation. When it relates to I/O + operations, this is an MMIO Store. + + + + System + Refers to the collection of hardware, system firmware, + and OS software which comprise a computer model. + + + + System address space + The total range of addressability as established by the + processor implementation. + + + + System Control Area + Refers to a range of addresses which + contains the system ROM(s) and an unarchitected, reserved, platform-dependent + area used by firmware and Run-Time Abstraction services for control of the + platform. The ROM areas are defined by the OF properties in the + openprom and os-rom nodes + of the OF device tree. + + + + System Information (Attention) indicator + See Error Log indicator. + + + + System firmware + Refers to the collection of all firmware on a system + including OF, RTAS and any legacy firmware. + + + + System Memory + Refers to those areas of memory which form + a coherency domain with respect to the PA processor or processors that + execute application software on a system. + + + + System software + Refers to the combination of OS software, + device driver software, and any hardware abstraction software, but + excludes the application software. + + + + TB + Time Base + + + + TCE + Translation Control Entry + + + + TLB + Translation Look-aside Buffer + + + + TOD + Time Of Day + + + + TOSM + Top of system memory + + + + TPM + Top of Peripheral Memory + Trusted Platform Module + + + + tty + Teletypewriter or ASCII character driven + terminal device + + + + UI + User Interface + + + + USB + Universal Serial Bus + + + + v + Volt + + + + VGA + Video Graphics Array + + + + VMC + Virtual Management Channel + + + + VPD + Vital Product Data + + + + VPNH + Virtual Processor Home Node option. See + + + . + + + + + + + + + + + + + + diff --git a/RTAS/bk_main.xml b/RTAS/bk_main.xml new file mode 100644 index 0000000..df88260 --- /dev/null +++ b/RTAS/bk_main.xml @@ -0,0 +1,111 @@ + + + + + + + Runtime Abstraction Services + Linux on Power Architecture Reference + + + + + System Software Work Group + + syssw-chair@openpowerfoundation.org + + OpenPOWER Foundation + + + + 2016 + OpenPOWER Foundation + + + Revision 2.0_pre1 + OpenPOWER + + + + + + Copyright details are filled in by the template. + + + + + + The purpose of this document is to provide firmware and software + architectural details associated with Runtime Abstraction Services (firmware) on OpenPOWER Systems. + The base content for this document were contributed to the OpenPOWER Foundation in the + IBM Linux on Power Architecture Platform Reference (LoPAPR) Draft + document. It had numerous contributors inside IBM. + This document is a Standard Track, Work Group Specification work product owned by the + System Software Workgroup and handled in compliance with the requirements outlined in the + OpenPOWER Foundation Work Group (WG) Process document. It was + created using the Master Template Guide version 0.9.5. Comments, + questions, etc. can be submitted to the public mailing list for this document at + TBD. + + + + + + 2016-05-04 + + + + Revision 2.0_pre1 - initial conversion from IBM document. Extracted from + Linux on Power Architecture Platform Reference (LoPAPR) version 1.1 dated March 24, + 2016 -- Chapter 7 (Run-time Abstration Services), Appendix G (Firmware Assisted + Dump Data Format), and Appendix I (CMO Characteristics Definition). + + + + + + + + + + + + + + + + + + + + + + + + + + + + + diff --git a/RTAS/ch_cmo_def.xml b/RTAS/ch_cmo_def.xml new file mode 100644 index 0000000..3808f8b --- /dev/null +++ b/RTAS/ch_cmo_def.xml @@ -0,0 +1,173 @@ + + + + + CMO Characteristics Definitions + + This chapter defines the string that is returned by the + ibm,get-system-parameter RTAS call when the parameter + token value of 44 (CMO Characteristics) is specified on the + ibm,get-system-parameter RTAS call as per + . + +
+ CMO Terms + The LoPAR Cooperative Memory Over-commitment option (CMO) defines + terms as presented in + . + + + CMO Terms + + + + + + + Term + + + Definition + + + + + CMO Page Size + + + Page size as determined by the hypervisor. CMO page size is + expressed as the power of 2 of the page size. For example, a 4K + page size is represented by the value of 12 (4K = 2 + 12). + + + + + Primary Paging Service Partition + + + The primary paging service partition identifies the primary + VIOS which provides access to paging services and devices for + partitions participating in CMO. The primary paging service + partition value is the partition number of the VIOS. + + + + + Secondary Paging Service Partition + + + The secondary paging service partition identifies the + secondary VIOS in a redundant Paging Service Partition + configuration. If the hypervisor detects a problem with the + primary VIOS, it fails over to the secondary VIOS. The secondary + paging service partition value is the partition number of the + secondary VIOS. + + + + +
+
+ +
+ Key Words And Values + + defines the key words and the + associated legal values that will be returned in the ASCII NULL terminated + string when the parameter token value of 44 (CMO characteristics) is + specified on the + ibm,get-system-parameter RTAS call. The key word and + value is separated by an ASCII equal (“=”). Each key word, + value pair is delimited by an ASCII comma in the string. The numerical + value of the characteristic corresponding to the key word is the decimal + number that corresponds to the numeric characters in the value part of the + key word, value pair. + + + CMO Characteristics + + + + + + + + + Characteristics + + + Key Word + + + Values + + + Notes + + + + + CMO Page Size + + + CMOPageSize + + + 1 - 64 + + +   + + + + + Primary Paging Service Partition + + + PrPSP + + + -1 through N + + + Set to -1 when the partition is not in CMO mode (i.e. is a + dedicated memory partition) + + + + + Secondary Paging Service Partition + + + SecPSP + + + -1 through N + + + + +
+
+ diff --git a/RTAS/ch_error_codes.xml b/RTAS/ch_error_codes.xml new file mode 100644 index 0000000..5f74a7d --- /dev/null +++ b/RTAS/ch_error_codes.xml @@ -0,0 +1,1272 @@ + + + + + Error Codes + +
+ Displaying Codes on the Standard Operator Panels + + + + + R1--1. + + Platform Implementation: Platforms must display + firmware progress codes (4 hex digits) on the operator panel display. On + 2x16 LCD displays, the progress codes are displayed left-justified on the + first line. + + + + + R1--2. + + Platform Implementation: Platforms must display + firmware error codes (8 hex digits) on the system console (graphic or + tty), and left-justified on the first line of a 2x16 LCD operator panel + display (if available). + + + + + R1--3. + + Platform Implementation: When a platform displays + firmware error codes, associated location codes must be displayed on the + following line on the system console (graphic or tty), and left-justified + on the second line of a 2x16 LCD operator panel display (if + available). + + + + + + The following describes in more detail the standard platform usage + of operator panel LEDs or LCDs for the display of firmware progress and + error codes. + + + + + Progress codes: Progress codes + from the system firmware and + service processor firmware are 4 hex digits in the range from 0x8000 + through 0xFFFF. Codes are displayed in the 4 character positions of a 1x4 + LED, or left justified in the first line of a 2x16 LCD. Subsequent + progress codes are displayed on top of (overlaying) the previous one. If + the system “hangs”, the last displayed progress code is left + on the display. + + + + + Error codes: Error codes are 8 + hex digits, as defined in + . These codes are displayed by + either boot ROM Power On Self Test (POST) or the service processor. If a + critical error is detected which prevents a successful boot or results in + system halt condition, the error code will be displayed left justified on + the first line of a 2x16 LCD. The error code is left on the LCD until the + system is reset or powered down. Error codes are not displayed on the + operator panel of platforms with only a 4-digit LED. On all platforms, + however, POST error codes are displayed on any system console (graphic or + tty). For non-critical errors where the system can boot and operate + normally or in a degraded mode, the associated error codes are not + displayed, but are reported to the OS via the POST error log and the RTAS + event-scan service. + + + + + Location Codes: Location codes + describe the physical location of + the most probable failing part associated with an error code. When an + error code is displayed on the first line of a 2x16 LCD, the location + code, if known, is displayed left justified on the second line. The + location code will remain on the LCD along with the error code until the + system is reset or powered down. Location codes for POST errors are also + displayed on any system console (graphic or tty), on the next line below + the error code. + + + + +
+ +
+ Firmware Error Codes + + The error code is an 8-character (4-byte) hexadecimal code produced + by firmware to identify the potential failing function or FRU in a + system. It consists of 5 source code characters and 3 reason code + characters. Individual characters within the error code have specific + field definitions, as defined in the following tables. + + + + + R1--1. + + Platform Implementation: To indicate the occurrence + of a critical platform error, platforms must display (either on an + operator panel or console) an 8-digit hex error code as defined in + and + . + + + + + + + + Table 155. Service Reference Code (SRC) Field Layout + + + + + + + + + + + + + + Source Code + + + + + Reason Code + + + + + + + + + Byte 0 + + + + + Byte 1 + + + + + Byte 2 + + + + + Byte 3 + + + + + + S1 + + + S2 + + + S3 + + + S4 + + + S5 + + + R1 + + + R2 + + + R3 + + + + +
+ + + Table 156. Service Reference Code (SRC) Field + Descriptions + + + + + + + + Field + + + + + Description + + + + + + + + S1 + + + Maintenance Package Source that produced the SRN + 0: Reserved + 1: Reserved + 2: POST, Firmware + 3: BIST + 4: Service processor, base system controller, etc. + 5: Reserved (potentially for use by AIX + Diagnostics) + 8: Product-Specific Service Guide, MAPs + 9: Reserved (potentially for use by the Problem Solving + Guide) + A-F: Reserved for future extension + + + + + S2 + + + Where applicable, use the lower nibble of the + + + base class code for the IOA definition (see + ). Only 00 to 0C are + currently defined in Revision 2.1, therefore the high nibble is + always zero. (There is a potential exposure that the high + nibble will be defined in the future, but currently there are + 13 base classes defined which include every device class, with + 3 remaining characters for future extension by the PCI SIG. + Therefore the exposure is in the far future.) For non-PCI + devices, use base class 0 to extend the definition (see + ). + + + + + S3-S4 + + + Where applicable, use the + + + subclass code for IOA definition (see + ). Also, extend the + definition to include non-PCI devices where it is not fully + utilized by PCI specification (see + ). + + + + + S5 + + + Unique version of the device/FRU type for a particular + product + + + + + R1 + + + Device/FRU unique failure reason codes. + For POST: assigned by Firmware Developer. + For AIX Diagnostics (S1 = 5, not currently + supported): + 1-7: Use in combination with R2,R3 for diagnostic test + failure when maximum isolation was obtained. + 8-9: Use in combination with R2,R3 for diagnostic test + failure when maximum isolation was NOT obtained. + A: Log analysis of POST error log + B: Log analysis of machine check or checkstop error + log + C: Log analysis of AIX device driver error log + D: diagnostic detected missing resource + E-F: Reserved + For others: assigned by respective developers. + + + + + R2-R3 + + + Device/FRU unique failure reason codes. + For POST: assigned by Firmware Developer + For others: assigned by respective developers. + + + + +
+ + + Table 157. Current PCI Class Code Definition + + + + + + + + + PCI Base Class (lower + nibble)S2 + + + + + PCI Sub-ClassS3-S4 + + + + + Description + + + + + + + + 0 + + + Devices that were built before the class code field was + defined + + + + + 00 + + + All currently implemented IOAs except VGA-compatible + IOAs. + + + + + 01 + + + VGA-compatible IOAs. + + + + + 1 + + + Mass storage controller. + + + + + 00 + + + SCSI bus controller. + + + + + 01 + + + IDE controller. + + + + + 02 + + + Floppy disk controller. + + + + + 03 + + + Intelligent Peripheral Interface (IPI) bus + controller. + + + + + 04 + + + Redundant Array of Independent Disks (RAID) + controller. + + + + + 80 + + + Other mass storage controller. + + + + + 2 + + + Network controller. + + + + + 00 + + + Ethernet controller. + + + + + 01 + + + Token Ring controller. + + + + + 02 + + + FDDI controller. + + + + + 03 + + + ATM controller. + + + + + 80 + + + Other Network controller. + + + + + 3 + + + Display controller. + + + + + 00 + + + VGA-Compatible controller. + + + + + 01 + + + Extended Graphics Array (XGA) controller. + + + + + 80 + + + Other display controller. + + + + + 4 + + + Multimedia device + + + + + 00 + + + Video device + + + + + 01 + + + Audio device + + + + + 80 + + + Other multimedia device + + + + + 5 + + + Memory controller. + + + + + 00 + + + RAM + + + + + 01 + + + Flash + + + + + 80 + + + Other memory controller. + + + + + 6 + + + Bridge IOAs. + + + + + 00 + + + Host bridge + + + + + 01 + + + Reserved + + + + + 02 + + + Reserved + + + + + 03 + + + Reserved + + + + + 04 + + + PCI-to-PCI bridge + + + + + 05 + + + Reserved + + + + + 06 + + + Reserved + + + + + 07 + + + Reserved + + + + + 80 + + + Other bridge device. + + + + + 7 + + + Simple communication controllers. + + + + + 00 + + + Serial controllers. + + + + + 01 + + + Parallel port. + + + + + 80 + + + Other communication controllers. + + + + + 8 + + + Generic system peripherals + + + + + 00 + + + PIC + + + + + 01 + + + DMA Controller. + + + + + 02 + + + System timer + + + + + 03 + + + Real-Time Clock (RTC) controller + + + + + 80 + + + Other system peripherals + + + + + 9 + + + Input devices + + + + + 00 + + + Keyboard controller + + + + + 01 + + + Digitizer (pen). + + + + + 02 + + + Mouse controller + + + + + 80 + + + Other input controllers. + + + + + A + + + Docking stations + + + + + 00 + + + Generic docking station + + + + + 80 + + + Other type of docking station + + + + + B + + + Processors + + + + + 20 + + + PA compliant (PowerPC and successors) + + + + + 40 + + + Co-processor + + + + + C + + + Serial bus controllers + + + + + 03 + + + Universal Serial Bus (USB) + + + + + 04 + + + Fibre Channel + + + + +
+ + + Table 158. S2-S3-S4 Definition for Devices/FRUs not Defined in + the PCI Specification + + + + + + + + + Base ClassS2 + + + + + Sub-ClassS3-S4 + + + + + Description + + + + + + + + 0 + + + 10 + + + AC Power + + + + + 11 + + + DC Power + + + + + 20 + + + Temperature Related Problem + + + + + 21 + + + Fans + + + + + 30-3x + + + Cables + + + + + 40-4x + + + Terminators + + + + + 50 + + + Operator panels + + + + + 60-6x + + + Reserved + + + + + 70-7x + + + Reserved + + + + + 90-9x + + + Reserved + + + + + A0 + + + Boot firmware Heartbeat + + + + + B0 + + + O/S Heartbeat + + + + + D0 + + + Unknown device + + + + + E0 + + + Security + + + + + 1 + + + A0 + + + SCSI Drives (generic) + + + + + B0 + + + IDE Drives + + + + + C0 + + + RAID Drives + + + + + D0 + + + SSA Drives + + + + + E0 + + + Tapes SCSI + + + + + E1 + + + Tapes IDE + + + + + ED + + + SCSI Changer + + + + + EE + + + Other SCSI Device + + + + + EF + + + Diskette drive + + + + + F0 + + + CDROM SCSI + + + + + F1 + + + CDROM IDE + + + + + F2 + + + Read/Write Optical SCSI + + + + + F3 + + + Read/Write Optical IDE + + + + + F4-FF + + + Reserved for other media devices + + + + + 5 + + + A0 + + + L2 Cache Controller including integrated SRAM + + + + + A1 + + + L2 Cache SRAM + + + + + A8 + + + NVRAM + + + + + A9 + + + CMOS + + + + + AA + + + Quartz/EEPROM + + + + + B0-Bx + + + Memory cards + + + + + Cyy + + + Memory DIMMs (yy = memory PD bits) + + + + + 7 + + + A0 + + + I2C bus + + + + + 8 + + + A0 + + + Power Management Functions + + + + + 9 + + + A0-Ax + + + Keyboards + + + + + B0-Bx + + + Mouse(s) + + + + + C0-Cx + + + Dials + + + + + D0 + + + Tablet + + + + + D1-Dx + + + Reserved for other input devices + + + + + B + + + A0 + + + Service processor + + + + +
+ +
+ + diff --git a/RTAS/ch_firmware_dump.xml b/RTAS/ch_firmware_dump.xml new file mode 100644 index 0000000..7d2a22b --- /dev/null +++ b/RTAS/ch_firmware_dump.xml @@ -0,0 +1,4072 @@ + + + + + Firmware Assisted Dump Data Format + + This Appendix documents the dump data format, in support of the + Configure Platform Assisted Kernel Dump option in + . + +
+ Register Save Area + The register save area is an area in the partition’s memory + used to preserve the registers for the active CPUs during a firmware + assisted dump. The location and size of this area is specified by the + partition when firmware assisted dump. The minimum size will be sent to the + partition in the PFDS KDUMP node. + The register save is a semi-free format list of registers for each + CPU. Each list of registers for a CPU starts with “CPUSTRT” and + ends with “CPUEND”. + NumCpusOffset should be used to access the data to allow for + additional fields to be added without affecting compatibility. + + Notes: + + + + + Only CPUs that are online at the start of the Firmware Assisted + Dump will have their register data saved. + + + + Each group of GPRs, FPRs, and VRs will be listed in ascending + array index (and ASCII identifier) sorted order with no other interleaving + registers. Further, registers whose value spans multiple doublewords + (currently only VR and VSR array elements) will be listed in high to low + sorted order with no other interleaving values. All other registers are not + required to be in any specific order (To make debug easier they will most + likely be placed in ascending ASCII identifier order) + + + + + Register Save Area Format + + + + + + + + + + + Offset + + + + + Length (Bytes) + + + + + Name + + + + + Value + + + + + Description + + + + + + + + 0x00 + + + 0x8 + + + Magic Number + + + 0x5245475341564500 “REGSAVE” + + + Identifies this area + + + + + 0x08 + + + 0x4 + + + Version + + + 0x0 + + + Current version + + + + + 0x0C + + + 0x4 + + + NumCpusOffset + + + 0x1C + + + Offset to NumCpus field + + + + + 0x10 + + + 0xC + + + Padding + + + 0x0 + + + Must be initialized to 0 + + + + + 0x1C + + + 0x4 + + + NumCpus + + + Actual number of CPUs + + + Number of CPUs (not the number of entries) + + + + + 0x20 + + + 0x10 + + + RegEntry + + + “CPUSTRT” + + +   + + + + + 0x30 + + + 0x10 + + + RegEntry + + + <various register values> + + +   + + + + + ... + + +   + + +   + + +   + + +   + + + + + 0x?? + + + 0x10 + + + RegEntry + + + “CPUEND” + + +   + + + + + 0x?? + + + 0x10 + + + RegEntry + + + “CPUSTRT” + + +   + + + + + ... + + +   + + +   + + +   + + +   + + + + +
+   + + RegEntry Format + + + + + + + + + + + Offset + + + + + Length (Bytes) + + + + + Name + + + + + Value + + + + + Description + + + + + + + + 0x0 + + + 0x8 + + + RegIdentifier + + + See Below + + + ASCII, Padded with binary zeros + + + + + 0x08 + + + 0x8 + + + RegData + + +   + + + Register Data + + + + +
+   + + CPUSTRT and CPUEND have the following format + + + + + + + + 8 Byte Identifier + + + 4 Byte Reserved + + + 4 Byte Logical CPU ID + + + + +
+   + + 8-Byte RegEntries + + + + + + + 8 Byte Identifier + + + 8 Byte Register Value + + + + +
+   + + 4-Byte RegEntries + + + + + + + + 8 Byte Identifier + + + 4 Byte Reserved + + + 4 Byte Register Value + + + + +
+   + + Identifiers Supported in Version 0x0 of the + Table + + + + + + + + + Identifier (Hex) + + + + + Identifier (ASCII) + + + + + Description + + + + + + + + 0x4350555354525400 + + + CPUSTRT + + +   + + + + + 0x435055454E440000 + + + CPUEND + + +   + + + + + 0x41434F5000000000 + + + ACOP + + + Available Coprocessor Register + + + + + 0x414D520000000000 + + + AMR + + + Authority Mask Register + + + + + 0x4346415200000000 + + + CFAR + + + Come From Address Register + + + + + 0x4352000000000000 + + + CR + + + Condition Register + + + + + 0x4354520000000000 + + + CTR + + + Count Register + + + + + 0x4354524C00000000 + + + CTRL + + + Control Register + + + + + 0x4441425200000000 + + + DABR + + + Data Address Breakpoint Register + + + + + 0x4441425258000000 + + + DABRX + + + DABR Extended + + + + + 0x4441520000000000 + + + DAR + + + Data Address Register + + + + + 0x4445430000000000 + + + DEC + + + Decrementer + + + + + 0x4453435200000000 + + + DSCR + + + Depth Stream Control Register + + + + + 0x4453495352000000 + + + DSISR + + + Data Storage Interrupt Status Register + + + + + 0x4650523030000000 + + + FPR00 + + + Floating Point Register 0 + + + + + 0x4650523031000000 + + + FPR01 + + + Floating Point Register 1 + + + + + 0x4650523032000000 + + + FPR02 + + + Floating Point Register 2 + + + + + 0x4650523033000000 + + + FPR03 + + + Floating Point Register 3 + + + + + 0x4650523034000000 + + + FPR04 + + + Floating Point Register 4 + + + + + 0x4650523035000000 + + + FPR05 + + + Floating Point Register 5 + + + + + 0x4650523036000000 + + + FPR06 + + + Floating Point Register 6 + + + + + 0x4650523037000000 + + + FPR07 + + + Floating Point Register 7 + + + + + 0x4650523038000000 + + + FPR08 + + + Floating Point Register 8 + + + + + 0x4650523039000000 + + + FPR09 + + + Floating Point Register 9 + + + + + 0x4650523130000000 + + + FPR10 + + + Floating Point Register 10 + + + + + 0x4650523131000000 + + + FPR11 + + + Floating Point Register 11 + + + + + 0x4650523132000000 + + + FPR12 + + + Floating Point Register 12 + + + + + 0x4650523133000000 + + + FPR13 + + + Floating Point Register 13 + + + + + 0x4650523134000000 + + + FPR14 + + + Floating Point Register 14 + + + + + 0x4650523135000000 + + + FPR15 + + + Floating Point Register 15 + + + + + 0x4650523136000000 + + + FPR16 + + + Floating Point Register 16 + + + + + 0x4650523137000000 + + + FPR17 + + + Floating Point Register 17 + + + + + 0x4650523138000000 + + + FPR18 + + + Floating Point Register 18 + + + + + 0x4650523139000000 + + + FPR19 + + + Floating Point Register 19 + + + + + 0x4650523230000000 + + + FPR20 + + + Floating Point Register 20 + + + + + 0x4650523231000000 + + + FPR21 + + + Floating Point Register 21 + + + + + 0x4650523232000000 + + + FPR22 + + + Floating Point Register 22 + + + + + 0x4650523233000000 + + + FPR23 + + + Floating Point Register 23 + + + + + 0x4650523234000000 + + + FPR24 + + + Floating Point Register 24 + + + + + 0x4650523235000000 + + + FPR25 + + + Floating Point Register 25 + + + + + 0x4650523236000000 + + + FPR26 + + + Floating Point Register 26 + + + + + 0x4650523237000000 + + + FPR27 + + + Floating Point Register 27 + + + + + 0x4650523238000000 + + + FPR28 + + + Floating Point Register 28 + + + + + 0x4650523239000000 + + + FPR29 + + + Floating Point Register 29 + + + + + 0x4650523330000000 + + + FPR30 + + + Floating Point Register 30 + + + + + 0x4650523331000000 + + + FPR31 + + + Floating Point Register 31 + + + + + 0x4650534352000000 + + + FPSCR + + + Floating Point Status and Control Register + + + + + 0x4750523030000000 + + + GPR00 + + + General Purpose Register 0 + + + + + 0x4750523031000000 + + + GPR01 + + + General Purpose Register 1 + + + + + 0x4750523032000000 + + + GPR02 + + + General Purpose Register 2 + + + + + 0x4750523033000000 + + + GPR03 + + + General Purpose Register 3 + + + + + 0x4750523034000000 + + + GPR04 + + + General Purpose Register 4 + + + + + 0x4750523035000000 + + + GPR05 + + + General Purpose Register 5 + + + + + 0x4750523036000000 + + + GPR06 + + + General Purpose Register 6 + + + + + 0x4750523037000000 + + + GPR07 + + + General Purpose Register 7 + + + + + 0x4750523038000000 + + + GPR08 + + + General Purpose Register 8 + + + + + 0x4750523039000000 + + + GPR09 + + + General Purpose Register 9 + + + + + 0x4750523130000000 + + + GPR10 + + + General Purpose Register 10 + + + + + 0x4750523131000000 + + + GPR11 + + + General Purpose Register 11 + + + + + 0x4750523132000000 + + + GPR12 + + + General Purpose Register 12 + + + + + 0x4750523133000000 + + + GPR13 + + + General Purpose Register 13 + + + + + 0x4750523134000000 + + + GPR14 + + + General Purpose Register 14 + + + + + 0x4750523135000000 + + + GPR15 + + + General Purpose Register 15 + + + + + 0x4750523136000000 + + + GPR16 + + + General Purpose Register 16 + + + + + 0x4750523137000000 + + + GPR17 + + + General Purpose Register 17 + + + + + 0x4750523138000000 + + + GPR18 + + + General Purpose Register 18 + + + + + 0x4750523139000000 + + + GPR19 + + + General Purpose Register 19 + + + + + 0x4750523230000000 + + + GPR20 + + + General Purpose Register 20 + + + + + 0x4750523231000000 + + + GPR21 + + + General Purpose Register 21 + + + + + 0x4750523232000000 + + + GPR22 + + + General Purpose Register 22 + + + + + 0x4750523233000000 + + + GPR23 + + + General Purpose Register 23 + + + + + 0x4750523234000000 + + + GPR24 + + + General Purpose Register 24 + + + + + 0x4750523235000000 + + + GPR25 + + + General Purpose Register 25 + + + + + 0x4750523236000000 + + + GPR26 + + + General Purpose Register 26 + + + + + 0x4750523237000000 + + + GPR27 + + + General Purpose Register 27 + + + + + 0x4750523238000000 + + + GPR28 + + + General Purpose Register 28 + + + + + 0x4750523239000000 + + + GPR29 + + + General Purpose Register 29 + + + + + 0x4750523330000000 + + + GPR30 + + + General Purpose Register 30 + + + + + 0x4750523331000000 + + + GPR31 + + + General Purpose Register 31 + + + + + 0x4C52000000000000 + + + LR + + + Link Register + + + + + 0x4D4D435230000000 + + + MMCR0 + + + Monitor Mode Control Register 0 + + + + + 0x4D4D435231000000 + + + MMCR1 + + + Monitor Mode Control Register 1 + + + + + 0x4D4D435240000000 + + + MMCRA + + + Monitor Mode Control Register A + + + + + 0x4D53520000000000 + + + MSR + + + Machine State Register + + + + + 0x4e49410000000000 + + + NIA + + + Next Instruction Address + + + + + 0x5049440000000000 + + + PID + + + Process ID Register + + + + + 0x5049520000000000 + + + PIR + + + Processor Identification Register + + + + + 0x504D433100000000 + + + PMC1 + + + Performance Monitor Counter 1 + + + + + 0x504D433200000000 + + + PMC2 + + + Performance Monitor Counter 2 + + + + + 0x504D433300000000 + + + PMC3 + + + Performance Monitor Counter 3 + + + + + 0x504D433400000000 + + + PMC4 + + + Performance Monitor Counter 4 + + + + + 0x504D433500000000 + + + PMC5 + + + Performance Monitor Counter 5 + + + + + 0x504D433600000000 + + + PIMC6 + + + Performance Monitor Counter 6 + + + + + 0x5055525200000000 + + + PURR + + + Processor Utilization Register + + + + + 0x5056520000000000 + + + PVR + + + Processor Version Register + + + + + 0x5344415200000000 + + + SDAR + + + Sampled Data Address Register + + + + + 0x5349415200000000 + + + SIAR + + + Sampled Instruction Address Register + + + + + 0x5350524730000000 + + + SPRG0 + + + Special Purpose Register General 0 + + + + + 0x5350524731000000 + + + SPRG1 + + + Special Purpose Register General 1 + + + + + 0x5350524732000000 + + + SPRG2 + + + Special Purpose Register General 2 + + + + + 0x5350524733000000 + + + SPRG3 + + + Special Purpose Register General 3 + + + + + 0x5350555252000000 + + + SPURR + + + Scaled Processor Utilization Register + + + + + 0x5352523000000000 + + + SRR0 + + + Save Restore Register 0 + + + + + 0x5352523100000000 + + + SRR1 + + + Save Restore Register 1 + + + + + 0x5442000000000000 + + + TB + + + Time Base Register + + + + + 0x5453520000000000 + + + TSR + + + Thread Status Register + + + + + 0x55414D4F52000000 + + + UAMOR + + + User Authority Mask Override Register + + + + + 0x565230305F484900 + + + VR00_HI + + + Vector Register 0 High + + + + + 0x565230305F4C4F00 + + + VR00_LO + + + Vector Register 0 Low + + + + + 0x565230315F484900 + + + VR01_HI + + + Vector Register 1 High + + + + + 0x565230315F4C4F00 + + + VR01_LO + + + Vector Register 1 Low + + + + + 0x565230325F484900 + + + VR02_HI + + + Vector Register 2 High + + + + + 0x565230325F4C4F00 + + + VR02_LO + + + Vector Register 2 Low + + + + + 0x565230335F484900 + + + VR03_HI + + + Vector Register 3 High + + + + + 0x565230335F4C4F00 + + + VR03_LO + + + Vector Register 3 Low + + + + + 0x565230345F484900 + + + VR04_HI + + + Vector Register 4 High + + + + + 0x565230345F4C4F00 + + + VR04_LO + + + Vector Register 4 Low + + + + + 0x565230355F484900 + + + VR05_HI + + + Vector Register 5 High + + + + + 0x565230355F4C4F00 + + + VR05_LO + + + Vector Register 5 Low + + + + + 0x565230365F484900 + + + VR06_HI + + + Vector Register 6 High + + + + + 0x565230365F4C4F00 + + + VR06_LO + + + Vector Register 6 Low + + + + + 0x565230375F484900 + + + VR07_HI + + + Vector Register 7 High + + + + + 0x565230375F4C4F00 + + + VR07_LO + + + Vector Register 7 Low + + + + + 0x565230385F484900 + + + VR08_HI + + + Vector Register 8 High + + + + + 0x565230385F4C4F00 + + + VR08_LO + + + Vector Register 8 Low + + + + + 0x565230395F484900 + + + VR09_HI + + + Vector Register 9 High + + + + + 0x565230395F4C4F00 + + + VR09_LO + + + Vector Register 9 Low + + + + + 0x565231305F484900 + + + VR10_HI + + + Vector Register 10 High + + + + + 0x565231305F4C4F00 + + + VR10_LO + + + Vector Register 10 Low + + + + + 0x565231315F484900 + + + VR11_HI + + + Vector Register 11 High + + + + + 0x565231315F4C4F00 + + + VR11_LO + + + Vector Register 11 Low + + + + + 0x565231325F484900 + + + VR12_HI + + + Vector Register 12 High + + + + + 0x565231325F4C4F00 + + + VR12_LO + + + Vector Register 12 Low + + + + + 0x565231335F484900 + + + VR13_HI + + + Vector Register 13 High + + + + + 0x565231335F4C4F00 + + + VR13_LO + + + Vector Register 13 Low + + + + + 0x565231345F484900 + + + VR14_HI + + + Vector Register 14 High + + + + + 0x565231345F4C4F00 + + + VR14_LO + + + Vector Register 14 Low + + + + + 0x565231355F484900 + + + VR15_HI + + + Vector Register 15 High + + + + + 0x565231355F4C4F00 + + + VR15_LO + + + Vector Register 15 Low + + + + + 0x565231365F484900 + + + VR16_HI + + + Vector Register 16 High + + + + + 0x565231365F4C4F00 + + + VR16_LO + + + Vector Register 16 Low + + + + + 0x565231375F484900 + + + VR17_HI + + + Vector Register 17 High + + + + + 0x565231375F4C4F00 + + + VR17_LO + + + Vector Register 17 Low + + + + + 0x565231385F484900 + + + VR18_HI + + + Vector Register 18 High + + + + + 0x565231385F4C4F00 + + + VR18_LO + + + Vector Register 18 Low + + + + + 0x565231395F484900 + + + VR19_HI + + + Vector Register 19 High + + + + + 0x565231395F4C4F00 + + + VR19_LO + + + Vector Register 19 Low + + + + + 0x565232305F484900 + + + VR20_HI + + + Vector Register 20 High + + + + + 0x565232305F4C4F00 + + + VR20_LO + + + Vector Register 20 Low + + + + + 0x565232315F484900 + + + VR21_HI + + + Vector Register 21 High + + + + + 0x565232315F4C4F00 + + + VR21_LO + + + Vector Register 21 Low + + + + + 0x565232325F484900 + + + VR22_HI + + + Vector Register 22 High + + + + + 0x565232325F4C4F00 + + + VR22_LO + + + Vector Register 22 Low + + + + + 0x565232335F484900 + + + VR23_HI + + + Vector Register 23 High + + + + + 0x565232335F4C4F00 + + + VR23_LO + + + Vector Register 23 Low + + + + + 0x565232345F484900 + + + VR24_HI + + + Vector Register 24 High + + + + + 0x565232345F4C4F00 + + + VR24_LO + + + Vector Register 24 Low + + + + + 0x565232355F484900 + + + VR25_HI + + + Vector Register 25 High + + + + + 0x565232355F4C4F00 + + + VR25_LO + + + Vector Register 25 Low + + + + + 0x565232365F484900 + + + VR26_HI + + + Vector Register 26 High + + + + + 0x565232365F4C4F00 + + + VR26_LO + + + Vector Register 26 Low + + + + + 0x565232375F484900 + + + VR27_HI + + + Vector Register 27 High + + + + + 0x565232375F4C4F00 + + + VR27_LO + + + Vector Register 27 Low + + + + + 0x565232385F484900 + + + VR28_HI + + + Vector Register 28 High + + + + + 0x565232385F4C4F00 + + + VR28_LO + + + Vector Register 28 Low + + + + + 0x565232395F484900 + + + VR29_HI + + + Vector Register 29 High + + + + + 0x565232395F4C4F00 + + + VR29_LO + + + Vector Register 29 Low + + + + + 0x565233305F484900 + + + VR30_HI + + + Vector Register 30 High + + + + + 0x565233305F4C4F00 + + + VR30_LO + + + Vector Register 30 Low + + + + + 0x565233315F484900 + + + VR31_HI + + + Vector Register 31 High + + + + + 0x565233315F4C4F00 + + + VR31_LO + + + Vector Register 31 Low + + + + + 0x5652534156450000 + + + VRSAVE + + + VR Save Register + + + + + 0x5653435200000000 + + + VSCR + + + VMX Status and Condition Register + + + + + 0x56535230305F4849 + + + VSR00_HI + + + Vector Scalar Register 0 High + + + + + 0x56535230305F4C4F + + + VSR00_LO + + + Vector Scalar Register 0 Low + + + + + 0x56535230315F4849 + + + VSR01_HI + + + Vector Scalar Register 1 High + + + + + 0x56535230315F4C4F + + + VSR01_LO + + + Vector Scalar Register 1 Low + + + + + 0x56535230325F4849 + + + VSR02_HI + + + Vector Scalar Register 2 High + + + + + 0x56535230325F4C4F + + + VSR02_LO + + + Vector Scalar Register 2 Low + + + + + 0x56535230335F4849 + + + VSR03_HI + + + Vector Scalar Register 3 High + + + + + 0x56535230335F4C4F + + + VSR03_LO + + + Vector Scalar Register 3 Low + + + + + 0x56535230345F4849 + + + VSR04_HI + + + Vector Scalar Register 4 High + + + + + 0x56535230345F4C4F + + + VSR04_LO + + + Vector Scalar Register 4 Low + + + + + 0x56535230355F4849 + + + VSR05_HI + + + Vector Scalar Register 5 High + + + + + 0x56535230355F4C4F + + + VSR05_LO + + + Vector Scalar Register 5 Low + + + + + 0x56535230365F4849 + + + VSR06_HI + + + Vector Scalar Register 6 High + + + + + 0x56535230365F4C4F + + + VSR06_LO + + + Vector Scalar Register 6 Low + + + + + 0x56535230375F4849 + + + VSR07_HI + + + Vector Scalar Register 7 High + + + + + 0x56535230375F4C4F + + + VSR07_LO + + + Vector Scalar Register 7 Low + + + + + 0x56535230385F4849 + + + VSR08_HI + + + Vector Scalar Register 8 High + + + + + 0x56535230385F4C4F + + + VSR08_LO + + + Vector Scalar Register 8 Low + + + + + 0x56535230395F4849 + + + VSR09_HI + + + Vector Scalar Register 9 High + + + + + 0x56535230395F4C4F + + + VSR09_LO + + + Vector Scalar Register 9 Low + + + + + 0x56535231305F4849 + + + VSR10_HI + + + Vector Scalar Register 10 High + + + + + 0x56535231305F4C4F + + + VSR10_LO + + + Vector Scalar Register 10 Low + + + + + 0x56535231315F4849 + + + VSR11_HI + + + Vector Scalar Register 11 High + + + + + 0x56535231315F4C4F + + + VSR11_LO + + + Vector Scalar Register 11 Low + + + + + 0x56535231325F4849 + + + VSR12_HI + + + Vector Scalar Register 12 High + + + + + 0x56535231325F4C4F + + + VSR12_LO + + + Vector Scalar Register 12 Low + + + + + 0x56535231335F4849 + + + VSR13_HI + + + Vector Scalar Register 13 High + + + + + 0x56535231335F4C4F + + + VSR13_LO + + + Vector Scalar Register 13 Low + + + + + 0x56535231345F4849 + + + VSR14_HI + + + Vector Scalar Register 14 High + + + + + 0x56535231345F4C4F + + + VSR14_LO + + + Vector Scalar Register 14 Low + + + + + 0x56535231355F4849 + + + VSR15_HI + + + Vector Scalar Register 15 High + + + + + 0x56535231355F4C4F + + + VSR15_LO + + + Vector Scalar Register 15 Low + + + + + 0x56535231365F4849 + + + VSR16_HI + + + Vector Scalar Register 16 High + + + + + 0x56535231365F4C4F + + + VSR16_LO + + + Vector Scalar Register 16 Low + + + + + 0x56535231375F4849 + + + VSR17_HI + + + Vector Scalar Register 17 High + + + + + 0x56535231375F4C4F + + + VSR17_LO + + + Vector Scalar Register 17 Low + + + + + 0x56535231385F4849 + + + VSR18_HI + + + Vector Scalar Register 18 High + + + + + 0x56535231385F4C4F + + + VSR18_LO + + + Vector Scalar Register 18 Low + + + + + 0x56535231395F4849 + + + VSR19_HI + + + Vector Scalar Register 19 High + + + + + 0x56535231395F4C4F + + + VSR19_LO + + + Vector Scalar Register 19 Low + + + + + 0x56535232305F4849 + + + VSR20_HI + + + Vector Scalar Register 20 High + + + + + 0x56535232305F4C4F + + + VSR20_LO + + + Vector Scalar Register 20 Low + + + + + 0x56535232315F4849 + + + VSR21_HI + + + Vector Scalar Register 21 High + + + + + 0x56535232315F4C4F + + + VSR21_LO + + + Vector Scalar Register 21 Low + + + + + 0x56535232325F4849 + + + VSR22_HI + + + Vector Scalar Register 22 High + + + + + 0x56535232325F4C4F + + + VSR22_LO + + + Vector Scalar Register 22 Low + + + + + 0x56535232335F4849 + + + VSR23_HI + + + Vector Scalar Register 23 High + + + + + 0x56535232335F4C4F + + + VSR23_LO + + + Vector Scalar Register 23 Low + + + + + 0x56535232345F4849 + + + VSR24_HI + + + Vector Scalar Register 24 High + + + + + 0x56535232345F4C4F + + + VSR24_LO + + + Vector Scalar Register 24 Low + + + + + 0x56535232355F4849 + + + VSR25_HI + + + Vector Scalar Register 25 High + + + + + 0x56535232355F4C4F + + + VSR25_LO + + + Vector Scalar Register 25 Low + + + + + 0x56535232365F4849 + + + VSR26_HI + + + Vector Scalar Register 26 High + + + + + 0x56535232365F4C4F + + + VSR26_LO + + + Vector Scalar Register 26 Low + + + + + 0x56535232375F4849 + + + VSR27_HI + + + Vector Scalar Register 27 High + + + + + 0x56535232375F4C4F + + + VSR27_LO + + + Vector Scalar Register 27 Low + + + + + 0x56535232385F4849 + + + VSR28_HI + + + Vector Scalar Register 28 High + + + + + 0x56535232385F4C4F + + + VSR28_LO + + + Vector Scalar Register 28 Low + + + + + 0x56535232395F4849 + + + VSR29_HI + + + Vector Scalar Register 29 High + + + + + 0x56535232395F4C4F + + + VSR29_LO + + + Vector Scalar Register 29 Low + + + + + 0x56535233305F4849 + + + VSR30_HI + + + Vector Scalar Register 30 High + + + + + 0x56535233305F4C4F + + + VSR30_LO + + + Vector Scalar Register 30 Low + + + + + 0x56535233315F4849 + + + VSR31_HI + + + Vector Scalar Register 31 High + + + + + 0x56535233315F4C4F + + + VSR31_LO + + + Vector Scalar Register 31 Low + + + + + 0x56535233325F4849 + + + VSR32_HI + + + Vector Scalar Register 32 High + + + + + 0x56535233325F4C4F + + + VSR32_LO + + + Vector Scalar Register 32 Low + + + + + 0x56535233335F4849 + + + VSR33_HI + + + Vector Scalar Register 33 High + + + + + 0x56535233335F4C4F + + + VSR33_LO + + + Vector Scalar Register 33 Low + + + + + 0x56535233345F4849 + + + VSR34_HI + + + Vector Scalar Register 34 High + + + + + 0x56535233345F4C4F + + + VSR34_LO + + + Vector Scalar Register 34 Low + + + + + 0x56535233355F4849 + + + VSR35_HI + + + Vector Scalar Register 35 High + + + + + 0x56535233355F4C4F + + + VSR35_LO + + + Vector Scalar Register 35 Low + + + + + 0x56535233365F4849 + + + VSR36_HI + + + Vector Scalar Register 36 High + + + + + 0x56535233365F4C4F + + + VSR36_LO + + + Vector Scalar Register 36 Low + + + + + 0x56535233375F4849 + + + VSR37_HI + + + Vector Scalar Register 37 High + + + + + 0x56535233375F4C4F + + + VSR37_LO + + + Vector Scalar Register 37 Low + + + + + 0x56535233385F4849 + + + VSR38_HI + + + Vector Scalar Register 38 High + + + + + 0x56535233385F4C4F + + + VSR38_LO + + + Vector Scalar Register 38 Low + + + + + 0x56535233395F4849 + + + VSR39_HI + + + Vector Scalar Register 39 High + + + + + 0x56535233395F4C4F + + + VSR39_LO + + + Vector Scalar Register 39 Low + + + + + 0x56535234305F4849 + + + VSR40_HI + + + Vector Scalar Register 40 High + + + + + 0x56535234305F4C4F + + + VSR40_LO + + + Vector Scalar Register 40 Low + + + + + 0x56535234315F4849 + + + VSR41_HI + + + Vector Scalar Register 41 High + + + + + 0x56535234315F4C4F + + + VSR41_LO + + + Vector Scalar Register 41 Low + + + + + 0x56535234325F4849 + + + VSR42_HI + + + Vector Scalar Register 42 High + + + + + 0x56535234325F4C4F + + + VSR42_LO + + + Vector Scalar Register 42 Low + + + + + 0x56535234335F4849 + + + VSR43_HI + + + Vector Scalar Register 43 High + + + + + 0x56535234335F4C4F + + + VSR43_LO + + + Vector Scalar Register 43 Low + + + + + 0x56535234345F4849 + + + VSR44_HI + + + Vector Scalar Register 44 High + + + + + 0x56535234345F4C4F + + + VSR44_LO + + + Vector Scalar Register 44 Low + + + + + 0x56535234355F4849 + + + VSR45_HI + + + Vector Scalar Register 45 High + + + + + 0x56535234355F4C4F + + + VSR45_LO + + + Vector Scalar Register 45 Low + + + + + 0x56535234365F4849 + + + VSR46_HI + + + Vector Scalar Register 46 High + + + + + 0x56535234365F4C4F + + + VSR46_LO + + + Vector Scalar Register 46 Low + + + + + 0x56535234375F4849 + + + VSR47_HI + + + Vector Scalar Register 47 High + + + + + 0x56535234375F4C4F + + + VSR47_LO + + + Vector Scalar Register 47 Low + + + + + 0x56535234385F4849 + + + VSR48_HI + + + Vector Scalar Register 48 High + + + + + 0x56535234385F4C4F + + + VSR48_LO + + + Vector Scalar Register 48 Low + + + + + 0x56535234395F4849 + + + VSR49_HI + + + Vector Scalar Register 49 High + + + + + 0x56535234395F4C4F + + + VSR49_LO + + + Vector Scalar Register 49 Low + + + + + 0x56535235305F4849 + + + VSR50_HI + + + Vector Scalar Register 50 High + + + + + 0x56535235305F4C4F + + + VSR50_LO + + + Vector Scalar Register 50 Low + + + + + 0x56535235315F4849 + + + VSR51_HI + + + Vector Scalar Register 51 High + + + + + 0x56535235315F4C4F + + + VSR51_LO + + + Vector Scalar Register 51 Low + + + + + 0x56535235325F4849 + + + VSR52_HI + + + Vector Scalar Register 52 High + + + + + 0x56535235325F4C4F + + + VSR52_LO + + + Vector Scalar Register 52 Low + + + + + 0x56535235335F4849 + + + VSR53_HI + + + Vector Scalar Register 53 High + + + + + 0x56535235335F4C4F + + + VSR53_LO + + + Vector Scalar Register 53 Low + + + + + 0x56535235345F4849 + + + VSR54_HI + + + Vector Scalar Register 54 High + + + + + 0x56535235345F4C4F + + + VSR54_LO + + + Vector Scalar Register 54 Low + + + + + 0x56535235355F4849 + + + VSR55_HI + + + Vector Scalar Register 55 High + + + + + 0x56535235355F4C4F + + + VSR55_LO + + + Vector Scalar Register 55 Low + + + + + 0x56535235365F4849 + + + VSR56_HI + + + Vector Scalar Register 56 High + + + + + 0x56535235365F4C4F + + + VSR56_LO + + + Vector Scalar Register 56 Low + + + + + 0x56535235375F4849 + + + VSR57_HI + + + Vector Scalar Register 57 High + + + + + 0x56535235375F4C4F + + + VSR57_LO + + + Vector Scalar Register 57 Low + + + + + 0x56535235385F4849 + + + VSR58_HI + + + Vector Scalar Register 58 High + + + + + 0x56535235385F4C4F + + + VSR58_LO + + + Vector Scalar Register 58 Low + + + + + 0x56535235395F4849 + + + VSR59_HI + + + Vector Scalar Register 59 High + + + + + 0x56535235395F4C4F + + + VSR59_LO + + + Vector Scalar Register 59 Low + + + + + 0x56535236305F4849 + + + VSR60_HI + + + Vector Scalar Register 60 High + + + + + 0x56535236305F4C4F + + + VSR60_LO + + + Vector Scalar Register 60 Low + + + + + 0x56535236315F4849 + + + VSR61_HI + + + Vector Scalar Register 61 High + + + + + 0x56535236315F4C4F + + + VSR61_LO + + + Vector Scalar Register 61 Low + + + + + 0x56535236325F4849 + + + VSR62_HI + + + Vector Scalar Register 62 High + + + + + 0x56535236325F4C4F + + + VSR62_LO + + + Vector Scalar Register 62 Low + + + + + 0x56535236335F4849 + + + VSR63_HI + + + Vector Scalar Register 63 High + + + + + 0x56535236335F4C4F + + + VSR63_LO + + + Vector Scalar Register 63 Low + + + + + 0x5845520000000000 + + + XER + + + Fixed-Point Exception Register + + + + +
+
+
+ Hardware Page Table Entry Save Area + The hardware page table entry save area is an area in the + partition’s memory used to preserve the hardware page table entries + corresponding to the VRMA entries that are used when Open Firmware is + started. The location and size of this area is specified by the partition + when firmware assisted dump. The minimum size is reported to the partition + in the new PFDS KDUMP node. + When accessing the table the offset to NumEntries should be used to + allow for different versions of the table. Newer versions of the table will + be compatible with all previous versions. +   + + HPT Entry Save Area Format + + + + + + + + + + + Offset + + + + + Length (Bytes) + + + + + Name + + + + + Value + + + + + Description + + + + + + + + 0x00 + + + 0x8 + + + Magic Number + + + 0x4850544553415645 + “HPTESAVE” + + + Used to verify that this area contains what it + should + + + + + 0x08 + + + 0x4 + + + Version + + + 0x0 + + + Current version + + + + + 0x0C + + + 0x4 + + + NumEntriesOffset + + + 0x1C + + + Offset to number of entries + + + + + 0x10 + + + 0x8 + + + Padding + + + 0x0 + + + Must be initialized to 0 + + + + + 0x18 + + + 0x8 + + + NumEntries + + + Actual Number Of Entries + + +   + + + + + 0x20 + + + 0x18 + + + HptEntry1 + + +   + + +   + + + + + 0x38 + + + 0x18 + + + HptEntry2 + + +   + + +   + + + + + ... + + +   + + +   + + +   + + +   + + + + +
+   + + HPT Entry Format + + + + + + + + + + + Offset + + + + + Length (Bytes) + + + + + Name + + + + + Value + + + + + Description + + + + + + + + 0x0 + + + 0x8 + + + HptEntryIndex + + +   + + + Index into the HPT table for the entry + + + + + 0x08 + + + 0x8 + + + Dword0 + + +   + + + HPT Entry High + + + + + 0x10 + + + 0x8 + + + Dword1 + + +   + + + HPT Entry Low + + + + +
+ + Note:The entries are not in any particular order. It + is up to the user of the save area to sort the data. + +
+ + diff --git a/RTAS/ch_rtas_call_defn.xml b/RTAS/ch_rtas_call_defn.xml new file mode 100644 index 0000000..c0e3942 --- /dev/null +++ b/RTAS/ch_rtas_call_defn.xml @@ -0,0 +1,24715 @@ + + + + + Call Function Definition + + This section specifies the semantics of all the RTAS calls. It + specifies the RTAS function name, the contents of its argument call buffer + (its token, input parameters, and output values) and semantics. + +
+ NVRAM Access Functions + This architecture requires an area of non-volatile memory (NVRAM) + to hold OF options, RTAS information, machine configuration state, OS + state, diagnostic logs, etc. The type and size of NVRAM is specified in + the OF device tree. The format of NVRAM is detailed in + . + In order to give the OS the ability to access + NVRAM on + different platforms that may use different implementations or locations + for NVRAM, a layer of abstraction is provided to the OS. The functions in + this section provide an interface for reading and writing NVRAM with byte + level operations with no boundary requirements. + +
+ <emphasis>nvram-fetch</emphasis> + The RTAS function + nvram-fetch copies data from a given offset in NVRAM + into the user specified buffer. + + + + R1--1. + + RTAS must implement an + nvram-fetch function that returns data from NVRAM + using the argument call buffer defined by + . + + + Argument Call Buffer + <emphasis>nvram-fetch</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + nvram-fetch + + + + + + Number Inputs + + + + 3 + + + + + + Number Outputs + + + + 2 + + + + + + Index + + + + Byte offset in NVRAM + + + + + + Buffer + + + + Real address of data buffer + + + + + + Length + + + + Size of data buffer (in bytes) + + + + + Out + + + + Status + + + + 0: Success + -1: Hardware Error + -3: Parameter out of range + + + + + + Num + + + + Number of bytes successfully copied + + + + +
+ + + + +
+ +
+ <emphasis>nvram-store</emphasis> + The RTAS function + nvram-store copies data from the user specified + buffer to a given offset in NVRAM. + + + + R1--1. + + RTAS must implement an + nvram-store function that stores data in NVRAM using + the argument call buffer defined by + . + + + Argument Call Buffer + <emphasis>nvram-store</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + nvram-store + + + + + + Number Inputs + + + + 3 + + + + + + Number Outputs + + + + 2 + + + + + + Index + + + + Byte number in NVRAM + + + + + + Buffer + + + + Real address of data buffer + + + + + + Length + + + + Size of data buffer (in bytes) + + + + + Out + + + + Status + + + + 0: Success + -1: Hardware Error + -3: Parameter out of range + + + + + + Num + + + + Number of bytes successfully copied + + + + +
+ + + + + R1--2. + + If the + nvram-store operation succeeded, the contents of + NVRAM must have been updated to the user specified values. The contents + of NVRAM are undefined if the RTAS call failed. + + Platform Implementation Note: The platform may keep + the NVRAM data cached in volatile memory as long as the cache is + implemented as a store-through cache and not a store-in cache. That is, + changed data is written to NVRAM as soon as possible. Return from the + nvram-store call with a “success” + Status is permissible after placing the data into a + store-through cache and prior to the actual writing to the NVRAM. + + + + + R1--3. + + The caller of the + nvram-store RTAS call must maintain the NVRAM + partitions as specified in + . + + + + +
+ +
+ +
+ Time of Day + The minimum system requirements include a non-volatile + real time + clock which maintains the time of day even if power to the machine is + removed. Minimum requirements for this clock are described in Requirement + + . + +
+ Time of Day Inputs/Outputs + The OS maintains the clock in UTC. This allows the OS and + diagnostics to co-exist with each other and provide uniform handling of + time. + + + + R1--1. + + The date and time inputs and outputs to + the RTAS time of day function calls are specified with the year as the + actual value (for example, 1995), the month as a value in the range 1-12, + the day as a value in the range 1-31, the hour as a value in the range + 0-23, the minute as a value in the range 0-59, and the second as a value + in the range 0-59. The date must also be a valid date according to common + usage: the day range being restricted for certain months, month 2 having + 29 days in leap years, etc. + + + + + R1--2. + + OSs must account for local time, for + daylight savings time when and where appropriate, and for leap + seconds. + + + + + R1--3. + + RTAS must account for leap years. + + + + +
+ +
+ <emphasis>get-time-of-day</emphasis> + + + + R1--1. + + RTAS must implement a + get-time-of-day call using the argument call buffer + defined by + . + + + Argument Call Buffer + <emphasis>get-time-of-day</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + get-time-of-day + + + + + + Number Inputs + + + + 0 + + + + + + Number Outputs + + + + 8 + + + + + Out + + + + Status + + + + 990x: Extended Delay where x is a number 0-5 (see text + below) + 0: Success + -1: Hardware Error + -2: Clock Busy, Try again later + + + + + + Year + + + + Year + + + + + + Month + + + + 1-12 + + + + + + Day + + + + 1-31 + + + + + + Hour + + + + 0-23 + + + + + + Minute + + + + 0-59 + + + + + + Second + + + + 0-59 + + + + + + Nanoseconds + + + + 0-999999999 + + + + +
+ + Software Implementation Note: When the 990x + Status is returned, it is suggested that software + delay for 10 raised to the x milliseconds (where x is the last digit of + the 990x return code), before calling again. However, software may issue + the call again either earlier or later than this. + + + + + R1--2. + + RTAS must read the current time and set + the output values to the best resolution provided by the platform. + + + + +
+ +
+ <emphasis>set-time-of-day</emphasis> + + + + R1--1. + + RTAS must implement a + set-time-of-day call using the argument call buffer + defined by + . + + + Argument Call Buffer + <emphasis>set-time-of-day</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + set-time-of-day + + + + + + Number Inputs + + + + 7 + + + + + + Number Outputs + + + + 1 + + + + + + Year + + + + Year + + + + + + Month + + + + 1-12 + + + + + + Day + + + + 1-31 + + + + + + Hour + + + + 0-23 + + + + + + Minute + + + + 0-59 + + + + + + Second + + + + 0-59 + + + + + + Nanosecond + + + + 0-999999999 + + + + + Out + + + + Status + + + + 990x: Extended Delay where x is a number 0-5 (see text + below) + 0: Success + -1: Hardware Error + -3: Parameter Error + + + + +
+ + Software Implementation Note: When the 990x + Status is returned, it is suggested that software + delay for 10 raised to the x milliseconds (where x is the last digit of + the 990x return code), before calling again. However, software may issue + the call again either earlier or later than this. + + + + + R1--2. + + RTAS must set the time of day to the best + resolution provided by the platform. + + + + + R1--3. + + RTAS must return a + Status of -3 (Parameter Error) to the + set-time-of-day RTAS call when the specified date is + outside the range supported by the platform. + Software Implementation Note: The OS maintains the clock in UTC. + This allows the OS and diagnostics to co-exist with each other and + provide uniform handling of time. Refer to Requirement + for further details on the time + of day clock. + + + + +
+ +
+ <emphasis>set-time-for-power-on</emphasis> + Some platforms provide the ability to set a time to cause the + platform power on. The + set-time-for-power-on call provides the interface to + the OS for setting this timer. + + + + R1--1. + + RTAS must implement the + set-time-for-power-on call using the argument call + buffer defined by + . + + + Argument Call Buffer + <emphasis>set-time-for-power-on</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + set-time-for-power-on + + + + + + Number Inputs + + + + 7 + + + + + + Number Outputs + + + + 1 + + + + + + Year + + + + Year + + + + + + Month + + + + 1-12 + + + + + + Day + + + + 1-31 + + + + + + Hour + + + + 0-23 + + + + + + Minute + + + + 0-59 + + + + + + Second + + + + 0-59 + + + + + + Nanosecond + + + + 0-999999999 + + + + + Out + + + + Status + + + + 990x: Extended Delay where x is a number 0-5 (see text + below) + 0: Success + -1: Hardware Error + -2: Clock Busy, Try again later + -3: Parameter Error + + + + +
+ + Software Implementation Note: When the 990x + Status is returned, it is suggested that software + delay for 10 raised to the x milliseconds (where x is the last digit of + the 990x return code), before calling again. However, software may issue + the call again either earlier or later than this. + + + + + R1--2. + + Hardware must support power on times of + up to four weeks into the future, at a minimum. + + + + + R1--3. + + RTAS must schedule the time for power on + as close as it can approach to the desired time. + + Software Implementation Note: Hardware limitations on + the duration of the power-on timer may result in power-on sooner than + requested by software. If present in the + /rtas node, the OF property + “power-on-max-latency” gives in days the + maximum power-on duration capability of the hardware. If the property is + not present, software should expect the default of a maximum of 28 days. + A “day” is defined as 24 hour increments from the current + time. + + + + + R1--4. + + If the system is in a powered down state + at the time scheduled by + set-time-for-power-on (within the accuracy of the + clock), then power must be reapplied and the system must go through its + power on sequence. + + + + + R1--5. + + RTAS must return a + Status of -3 (Parameter Error) to the + set-time-for-power-on RTAS call when the specified + date is outside the range supported by the platform (such as before + current TOD). + + + + +
+ +
+ +
+ Error and Event Reporting + The error and event reporting RTAS calls are designed to provide an + abstract interface into hardware registers in the system that may contain + correctable or non-correctable errors and to provide an abstract + interface to certain platform events that may be of interest to the OS. + Such errors and events may be detected either by a periodic scan or by an + exception trap. + These functions are not intended to replace the normal error + handling in the OS. Rather, they enhance the OS’s abilities by + providing an abstract interface to check for, report, and recover from + errors or events on the platform that are not necessarily known to the + OS. + The OS uses the error and event RTAS calls in two distinct + ways: + + + + Periodically, the OS calls + event-scan + to have the + system firmware check for any errors or events that have occurred. + + + + Whenever the OS receives an interrupt or exception that it + cannot fully process, it calls + check-exception.. + + + + The first case covers all errors and events that do not signal + their occurrence with an interrupt or exception. The second case covers + those errors and events that do signal with an interrupt or exception. It + is platform dependent whether any specific error or event causes an + interrupt on that platform. + + + + R1--1. + + RTAS must return the event generated by a + particular interrupt or event source by either + check-exception or + event-scan, but not both. + + + + + R1--2. + + check-exception and + event-scan, on a 64-bit capable platform, must be + able to handle platform resources that are accessed using 64-bit + addresses when instantiated in 32-bit mode. + + + + +
+ <emphasis>event-scan</emphasis> + + + + R1--1. + + RTAS must implement an + event-scan + call using + the argument call buffer defined by + . + + + Argument Call Buffer + <emphasis>event-scan</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + event-scan + + + + + + Number Inputs + + + + 4 + + + + + + Number Outputs + + + + 1 + + + + + + Event Mask + + + + Mask of event classes to process + + + + + + Critical + + + + Indicates whether this call is required to complete + quickly + + + + + + Buffer + + + + Real address of error log + + + + + + Length + + + + Length of error log buffer + + + + + Out + + + + Status + + + + 1: No Errors Found + 0: New Error Log returned + -1: Hardware Error + + + + +
+ + + + + R1--2. + + The event-scan call must fill in the error log with a + single error log formatted as specified in + . If necessary, the data placed + into the error log must be truncated to + length bytes. + + + + + R1--3. + + RTAS must only check for errors or events + that are within the classes defined by the + Event mask. Event mask is a bit mask of error and + event classes. Refer to + for the definition of the bit + positions. + + + + + R1--4. + + If Critical is non-zero, then RTAS must perform only + those operations that are required for continued operation. No extended + error information is returned. + + + + + R1--5. + + The event-scan call must return the first found error or + event and clear that error or event so it is only reported once. + + + + + R1--6. + + The OS must continue to call + event-scan while a + Status of “New Error Log returned” is + returned. + + + + + R1--7. + + The event-scan call must be made at least + “rtas-event-scan-rate” + times per minute for each error and event class and + must have the + Critical parameter equal to 0 for this periodic + call. + + + + + R1--8. + + The platform must not return more than + two error logs during the first sequence of + event-scan RTAS calls after boot of an OS image, and + must not return more than one error log to that OS image during any + sequence of + event-scan RTAS calls after the first time a non-zero + Status is returned. + + + + + + Software Implementation Notes: + + + + In a multiprocessor system, each processor should call + event-scan periodically, not always the same one. The + event-scan function needs to be called a total of + “rtas-event-scan-rate” + times a minute. + + + + The maximum size of the error log is specified in the OF device + tree as the + “rtas-error-log-max” + property of the + /rtas node. + + + + This call does not log the error in NVRAM. It returns the error + log to the OS. It is the responsibility of the OS to take appropriate + action. + + + + For best system performance, the requested + “rtas-event-scan-rate” should be as low + as possible, and as a goal should not exceed 120 scans per minute. + Maximum system performance is obtained when no scans are required. + + + +
+ +
+ <emphasis>check-exception</emphasis> + + + + R1--1. + + RTAS must implement a + check-exception call using the argument call buffer + defined by + . + + + Argument Call Buffer + <emphasis>check-exception</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + check-exception + + + + + + Number Inputs + + + + 6 (without Extended Information) + 7 (with Extended Information) + + + + + + Number Outputs + + + + 1 + + + + + + Vector Offset + + + + The vector offset for the exception. See + + + . + + + + + + Additional Information + + + + Information which RTAS may need to determine the cause of + the exception, but which may be unavailable to it in hardware + registers. See + for details. + + + + + + Event Mask + + + + Mask of event classes to process + + + + + + Critical + + + + Indicates whether this call is required to complete + quickly + + + + + + Buffer + + + + Real address of error log + + + + + + Length + + + + Length of error log + + + + + + Extended Information + + + + See Requirement + . + + + + + Out + + + + Status + + + + 1: No Errors Found + 0: New Error Log returned + -1: Hardware Error + + + + +
+ + + + + R1--2. + + The OS must provide the value specified in + in the + Additional Information parameter in the call to + check-exception, with the + Number Inputs parameter set to 6. If the value (e.g., + SRR1) is too large to fit in this cell, the lower 32-bits must be + provided here, the upper 32-bits provided in the + Extended Information parameter, and the + Number Inputs parameter set to 7. + + + Additional Information Provided to + <emphasis>check-exception</emphasis> call + + + + + + + + Source of Interrupt + + + + + Value of “Additional + Information” Variable + + + + + + + + External Interrupt + + + Interrupt number + + + + + Machine check exception + + + Value of register SRR1 at entry to machine check + handler + + + + + System Reset exception + + + Value of register SRR1 at entry to system reset + handler + + + + + Other exception + + + Value of register SRR1 at entry to exception + handler + + + + +
+ + + + + R1--3. + + The check-exception call must fill in the error log with + a single error log formatted as specified in + . The data in the error log + must be truncated to + length bytes. + + + + + R1--4. + + If Critical is non-zero, then RTAS must perform only + those operations that are required for continued operation. No extended + error information is returned. + + + + + R1--5. + + The check-exception call must return the first found + error or event and clear that error or event so it is only reported + once. + + + + + R1--6. + + RTAS must only check for errors or events + that are within the classes defined by the + Event mask. Event mask is a bit mask of error and + event classes. Refer to + for the definition of the bit + positions. + + + + + Software Implementation Notes: + + + + All OS reserved exception handlers should call + check-exception to process any errors that are + unknown to the OS. + + + + The + interrupt number for external device interrupts is + provided in the OF device tree as specified in + . + + + + Software, with knowledge of the class of event it seeks, matches + the data in the Vector Offset, Additional Information, and Extended + Information with the Event Mask such that ambiguity does not + result. + + + +
+ +
+ <emphasis>rtas-last-error</emphasis> + + + + R1--1. + + RTAS must implement an + rtas-last-error call using the argument call buffer + defined in + . + + + Argument Call Buffer + <emphasis>rtas-last-error</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + rtas-last-error + + + + + + Number Inputs + + + + 2 + + + + + + Number Outputs + + + + 1 + + + + + + Buffer + + + + Real address of error log + + + + + + Length + + + + Length of error log buffer + + + + + Out + + + + Status + + + + 1: No Errors Found + 0: New Error Log Returned + -1: Hardware Error (cannot create log) + + + + +
+ + + + + R1--2. + + The rtas-last-error call must fill in the error log with + a single error log formatted as specified in + . If necessary, the data placed + into the error log must be truncated to ‘length” + bytes. + + + + + R1--3. + + RTAS must only check for hardware errors + that occurred during a prior call to some other RTAS function, resulting + in a -1 (Hardware Error) return + Status. + + + + + + Software Note: This function is intended to provide + the OS with more detailed failure information after an RTAS call returns + with a -1 (Hardware Error) + Status, and should not be called except for this + purpose. If + rtas-last-error itself returns a -1 + Status, then it could not create the error log data + because of a further error, and the OS should not try to call it + again. +
+ +
+ Platform Dump Option + + The architectural intent of the Platform Dump option is to allow a + mechanism for the platform to communicate a variety of dump data used to + debug problems within the platform firmware or hardware. + +
+ <emphasis>ibm,platform-dump</emphasis> + + This RTAS call is used to transfer dump data from the platform to + the OS. It is expected that this routine will have to be called several + times to complete the transfer of the diagnostic dump data. It is also + anticipated that multiple dumps could be in the process of completion at + the same time. Individual dumps are identified by a dump tag passed by + the OS. The OS may interleave calls to + ibm,platform-dump with different RTAS calls. Other + standard RTAS locking rules apply (for example, only one processor may + call RTAS at a time). + The OS only makes the + ibm,platform-dump RTAS call when an event scan + returns an error log with an Event Type of “Dump + Notification” as described in Version 6 or later of the RTAS + General Extended Error Log Format. + + + + R1--1. + + For the Platform Dump option: The RTAS function + ibm,platform-dump must be implemented and must + implement the argument call buffer as defined by + . + + + Argument Call Buffer + <emphasis>ibm,platform-dump</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,platform-dump + + + + + + Number of Inputs + + + + 6 + + + + + + Number of Outputs + + + + 5 + + + + + + Dump_Tag_Hi + + + + Most-significant 32 bits of a Dump_Tag representing an id + of the dump being processed + + + + + + Dump_Tag_Lo + + + + Least-significant 32 bits of a Dump_Tag representing an + id of the dump being processed + + + + + + Sequence_Hi + + + + Most-significant 32 bits of the Sequence, a value + indicating what portion of a dump to be returned by the call. + Sequence of 0 returns the beginning of the Dump. The value in + all subsequent call as needed, should be set to the value of + the Next_Sequence returned from each previous call. + + + + + + Sequence_Lo + + + + Least-significant 32 bits of the Sequence + + + + + + Buffer + + + + Address of dump buffer (NULL indicates completion of + processing) + + + + + + Length + + + + Length of the buffer in bytes (min. 1024) + + + + + Out + + + + Status + + + + -1: Hardware error + -2: Busy, try again later + -9002: Not Authorized + 0: Dump complete + 1: Continue dump + 990x: Extended Delay where x is a number 0-5 + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + Next_Sequence_Hi + + + + Most-significant 32 bits of the Next_Sequence value + indicating the portion of the dump to be retrieved on the next + call if needed. (If + Status is returned as 0, then the dump is + complete and there is no next call required. The value of + Next_Sequence in this case is undefined.) + + + + + + Next_Sequence_Lo + + + + Least-significant 32 bits of the Next_Sequence + value + + + + + + Bytes_Returned_Hi + + + + Most-significant 32 bits of the Bytes_Returned value + indicating the number of valid bytes returned in the + Buffer + + + + + + Bytes_Returned_Lo + + + + Least-significant 32 bits of the Bytes_Returned value + indicating the number of valid bytes returned in the + Buffer + + + + +
+ + Software Implementation Note: When the 990x + Status is returned, it is suggested that software + delay for 10 raised to the x milliseconds (where x is the last digit of + the 990x return code), before calling + ibm,platform-dump again. However, software may issue + the + ibm,platform-dump call again either earlier or later + than this. + + + + + R1--2. + + For the Platform Dump option: On the first call to + ibm,platform-dump of a platform dump sequence for a + given Dump_Tag, the Sequence value must be initialized to zero and on + subsequent calls for the same tag, the Dump_Sequence must be set to + Next_Sequence of the previous call made with the same Dump_Tag or else + set to zero to restart the entire dump sequence. + + + + + R1--3. + + For the Platform Dump option: The dump tag passed to + any call to ibm,platform-dump must be a value specified by the platform + and communicated to the OS by an + event-scan error log entry. + + + + + R1--4. + + For the Platform Dump option: Once a + Status of 0 (Dump complete) or -1 (Hardware + error” is returned for the + ibm,platform-dump call with a particular dump tag, + the dump is considered complete from a platform standpoint, but for the + “Dump complete” case the OS must signal to the platform that + the processing of the dump has been completed by a final call for the + Dump_Tag with the Buffer address set to NULL. + + + + + R1--5. + + For the Platform Dump option: If at any time a + partition receives a -9002, Not Authorized, return code for an + ibm,platform-dump RTAS, the partition must cease + attempting to acquire the dump information it was in process of acquiring + and discard any portion already acquired. + + Programming Note: It is expected that a platform + generally only transmits a dump to a single partition. However, the above + requirement makes provision for the platform abandoning the transmission + of a dump to a partition after it has been initiated, presumably to + re-initiate transmission to a different partition or to a Hardware + Management Console (HMC). + + + + + R1--6. + + For the Platform Dump option: The contents of dump + information returned through the sequence of calls to + ibm,platform-dump, must follow a dump directory + structure as defined in + . + + + + + R1--7. + + For the Platform Dump option: Collectively the dump + data returned from a sequence of + ibm,platform-dump calls for a given Dump_tag must + consist of one dump file directory entry as described in + followed by one or more dump + section directory entries as described in + followed by a dump data section + for each dump section directory entry earlier included. + + + + + + Programming Notes: + + + + + As required in + , the OS can determine the + maximum size of a copy of each dump that can be returned by issuing an + ibm,get-system-parameter for the + platform-dump-max-size. In addition, in the case of any change in the + value of this parameter, the platform may generate a Platform Event Log + entry announcing the change in the maximum size, and specifying the new + size in the IO Events Section. This entry, when generated, is then + returned by the + event-scan RTAS call. + + + + The Dump_Tag is taken from the Dump Locator Section of the + Platform Error/Event Log Format, Version 6 or later. Specifically, + Dump_Tag_Hi is composed of the 8 bit Dump Type as found in the Dump + Locator Section, padded with 24 bits on the left to make a 32 bit + quantity. The Dump_Tag_Lo is the Dump ID found in the Dump Locator + Section of the Error log entry. + + + + If the + ibm,platform-dump RTAS routine returns with the + Status of 1 (Continue dump), the transfer is + proceeding but had to be suspended to maintain the short execution time + requirement of RTAS routines or because more data was available than the + Buffer could contain. + + + + The Bytes_Returned value indicates how many bytes of dump data + (if any) were returned on a call and OS must be prepared to handle the + case of no bytes returned. When Continue dump + Status (1) is returned, this indicates that there is + more dump data available then was returned in the buffer. A subsequent + call with the same Dump_tag and the Sequence value being set to the + Next_Sequence returned from the previous call returns additional dump + data. + + + + When a dump has been successfully transmitted, the + Status of 0 (Dump complete) is returned. If there is + a hardware error preventing a dump from being successfully transmitted, + as + Status of -1 (Hardware error) is returned. In either + case, the Dump sequence is completed. It should be noted that the final + Next_Sequence value returned is undefined. After the sequence is + completed, the OS should make one final call for the given Dump_Tag using + a NULL buffer pointer. (The value of the Sequence parameter for this call + is undefined although it is acceptable for the platform to make the value + equal to the last Next_Sequence value returned.) This call tells the + platform that the OS has completed processing of the dump and will not + attempt to restart the sequence. + + + + If the platform used system memory to hold dump data, the + platform at this point is permitted to free the associated logical memory + blocks (LMBs) reserved for the dump. Successful return from the + ibm,platform-dump RTAS call with a NULL buffer + pointer indicates to the OS that one or more logical memory blocks (LMBs) + may now be acquired by the OS. A get-sensor-state RTAS call for these + LMBs returns with a state of “DR entity available for recovery + (4)” after the successful return from this + ibm,platform-dump RTAS call. + + + + If a platform does not receive the NULL buffer pointer call dump + for a given Dump_Tag but subsequently boots the partition, the platform + may report the presence of the dump again on an e + vent-scan after the boot. + + + +
+ +
+ Platform Dump Directory Structure + + The entire dump contents returned over a sequence of + ibm,platform-dump RTAS calls for a given Dump_Tag + follows a directory/data structure as illustrated in + and + where a dump consists of one + File Directory Entry, one or more Section Directory Entries and one data + section for each Section Directory entry. + + + Platform Dump File Directory Entry Format + + + + + + + + + + Field Name + + + + + Length + + + + + Values + + + + + Discussion + + + + + + + + Entry Header + + + 8 Bytes + + + “FILE” + + + Identifies the type of entry that follows. The value is + ASCII consisting of the characters “FILE” and 4 + ASCII blanks. + + + + + Entry Length + + + 2 Bytes + + + Number of bytes of the entire file directory entry + + + This length includes the Entry Header and Entry Length + fields. + + + + + Reserved + + + 6 Bytes + + +   + + +   + + + + + Flags + + + 4 Bytes + + + See + . + + +   + + + + + Entry Type + + + 2 Bytes + + + 0x0001 + + + 0x0001signifies a file entry. + + + + + Prefix Length + + + 2 Bytes + + + Number of bytes of the Dump File Base Name that is + considered to be a prefix. + + +   + + + + + Dump File Base Name + + + Length in bytes computed as “Entry length” - + 24, but not to exceed 46 characters including the ASCII NULL + string termination. + + + NULL terminated ASCII String consisting of ASCII + characters in the ranges of a-z, A-Z, 0-9, and the ASCII + “.” + + + Gives a base name for the dump file to be created from + the dump data. This base name is composed of a prefix followed + by additional data (e.g. dumptype.serialnumber.dumpID.timestamp + where dumptype.serialnumber is the prefix) + + + + +
+ + + Dump Section Directory Entry Format + + + + + + + + + + Field Name + + + + + Length + + + + + Values + + + + + Discussion + + + + + + + + Entry Header + + + 8 Bytes + + + “SECTION” + + + Identifies the type of entry that follows. The value is + ASCII consisting of the characters “SECTION” and 1 + ASCII blank. + + + + + Entry Length + + + 2 Bytes + + + Number of bytes of the entire section directory + entry + + + This length includes the Entry Header and Entry Length + fields. + + + + + Priority + + + 2 Bytes + + + Unsigned integer + + + See programming note after + . + + + + + Reserved + + + 4 Bytes + + +   + + +   + + + + + Flags + + + 4 Bytes + + + See + . + + +   + + + + + Entry Type + + + 2 Bytes + + + 0x0002 + + + 0x0002 signifies a section entry. + + + + + Reserved + + + 2 Bytes + + +   + + +   + + + + + Section Length + + + 8 Bytes + + + Length in bytes of the section of the dump that this + entry is the directory for + + +   + + + + + Section Name + + + Length in bytes computed as “Entry length” - + 32, but not to exceed 46 characters including the ASCII NULL + string termination. + + + NULL terminated ASCII String. + + + Gives a name to the dump section for which this entry is + a directory. + + + + +
+ The two previous tables refer to a set of flags used to describe + information related to a dump section. The options are stored in a single + 32 bit value which is the bit-wise OR'ing of each option value defined in + + . + + + Dump File Format Directory Options + + + + + + + + + + Name + + + + + Bit Position(s) of Option + + + + + Definition + + + + + Discussion + + + + + + + + last_flag + + + 0x00000001 + + + Binary value set to 1 if the last directory entry. + + + Flag is never set for the File Directory entry since at + least one Section Directory entry follows. + + + + + not_transmitted + + + 0x00000002 + + + If set to 1, indicates that the data for the block has + not been transmitted during some process of dump + transfer. + + + Platform always sets this value to 0. The bit may be set + to 1 by applications transmitting a dump. See Software + implementation note item 2: in this section below. + + + + + Reserved + + + All but bit positions shown above + + + All other values reserved + + +   + + + + +
+ + Software Implementation Notes: + + + + + Platforms supporting the + ibm,platform-dump call may have several unique dump + types. All dumps of the same type on a partition have the same + “prefix” to the name of the dump file as indicated in the + dump file directory entry in an error log. + + + + The priority in the priority field of the section directory + entries allow an application transmitting a dump to a remote support + center to decide what sections of data to transmit when the connection + bandwidth is limited. Zero is the highest priority. All sections at the + same priority shall be transmitted if any at that priority are + transmitted. It is intended that all directory entries be transmitted + with the section length set to zero and their not_transmitted Dump File + Format Directory Options flag set to a 1 if the section data cannot be + transmitted. + + + +
+ +
+ +
+ +
+ PCI Configuration Space + Device drivers and system software need access to + PCI + configuration space. + section on "Address Map" defines + system address spaces for PCI memory and PCI I/O spaces. It does not + define an address space for PCI configuration. Different PCI bridges may + implement the mechanisms for accessing PCI configuration space in + different ways. The RTAS calls in this section provide an abstract way of + reading and writing PCI configuration spaces. + The PCI access functions take a + config_addr input parameter which is similar to the + Type 1 PCI configuration space address. For conventional PCI and PCI-X + Mode 1, this address is a 24-bit quantity composed of bus, device, + function, and register numbers. This allows the configuration of up to + 256 buses (including sub-bridges), 32 IOAs per bus, 8 functions per IOA, + and 256 bytes of register space per function. PCI-X Mode 2 and PCI + Express define an extended configuration space with an additional 4-bit + quantity which specifies an extended register number allowing for 4096 + bytes of register space per function. Refer to the + or the + for more details. The + config_addr for an IOA is derived from the OF device tree, and is defined + in + . + The + ibm,read-pci-config and + ibm,write-pci-config RTAS calls allow for the + specification of the PHB Bus Unit ID, and therefore allow for up to 256 + unique + config_addr bus numbers per PHB. Note that for each + pci connector, there may be multiple PCI bus numbers, because plug-in PCI + cards may contain PCI to PCI bridges, which create other PCI + buses. + The + PCI Local Bus Specification requires that + unimplemented or reserved register space read as 0’s, and that + reads of the Vendor ID register of IOAs or functions which aren’t + present should be unambiguously reported (reading 0xFFFF is sufficient). + Writes to unimplemented or reserved register space are specified as + no-ops. Writes to IOAs or functions which aren’t present are + undefined. These operations are undefined if a bus is specified which + doesn’t exist. + + + + R1--1. + + For the RTAS PCI + configuration space and EEH functions where the parameter + config_addr is requested as input, the + config_addr parameter must be as specified by the hi + cell of the physical address in Open Firmware Working Group proposal + number 516 Ver 1.8 (see + ), with the upper register + address bits added for PCI-X Mode 2 and PCI Express, in order to access + past the first 256 bytes of configuration space. + + + Definition + <emphasis>Config_addr</emphasis> + + + + + + + + Bit + + + + + Definition + + + + + + + + 0:3 + + + Upper bits of the Register Number, when applicable, + otherwise 0. Set to 0 when the PCI extended configuration space + is not available, due to lack of support somewhere from the PHB + to the IOA. When a value of this field can be something other + than 0, the + + “ibm,pci-config-space-type” property will + exist in the IOA's node with a value indicating that the + extended space is supported. + + + + + 4:7 + + + Reserved (set to 0) + + + + + 8:15 + + + Bus Number + + + + + 16:20 + + + Device Number + + + + + 21:23 + + + Function Number, when applicable, otherwise 0 + + + + + 24:31 + + + Lower bits of the Register Number, when applicable, + otherwise 0 + + + + +
+ + + + + R1--2. + + All RTAS PCI Read/Write functions must + follow the appropriate PCI specification. + + + + + R1--3. + + RTAS must follow the rules of + when accessing PCI + configuration space. + + + + + + Software Implementation Notes: + + + + + Since PCI Configuration space is defined to be Little-Endian, + RTAS accesses this area using the byte-reversed forms of the + Load and + Store instructions. In this fashion, the values + passed are defined Big-Endian. + + + + Prior to accessing the extended configuration address space of + PCI-X Mode 2 and PCI Express devices, an IOA device driver is responsible + for checking if the + “ibm,pci-config-space-type” property (see + ) of the IOA's node exists and + is set to a non-zero value. + + + +
+ <emphasis>ibm,read-pci-config</emphasis> + + + + R1--1. + + For Platforms which may have greater than 256 PCI + Buses: RTAS must implement an + ibm,read-pci-config + call using + the argument call buffer defined by + . + + + Argument Call Buffer + <emphasis>ibm,read-pci-config</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,read-pci-config + + + + + + Number Inputs + + + + 4 + + + + + + Number Outputs + + + + 2 + + + + + + Config_addr + + + + Configuration Space Address + + + + + + PHB_Unit_ID_Hi + + + + Represents the most-significant 32-bits of the Unit ID of + the PHB that corresponds to the + config_addr + + + + + + PHB_Unit_ID_Low + + + + Represents the least-significant 32-bits of the Unit ID + of the PHB that corresponds to the + config_addr + + + + + + Size + + + + Size of Configuration Cycle in bytes, value can be 1, 2, + or 4 + + + + + Out + + + + Status + + + + 0: Success + -1: Hardware Error + -3: Parameter Error + + + + + + Value + + + + Value Read from the location specified by the PHB Unit ID + and config_addr + + + + +
+ + + + + R1--2. + + The + ibm,read-pci-config call must return the value from + the configuration register which is at the location specified by the PHB + Unit ID and + config_addr in PCI configuration space. + + + + + R1--3. + + The ibm,read-pci-config call must perform a 1-byte, + 2-byte, or 4-byte configuration space read depending on the value of the + size input argument. + + + + + R1--4. + + The config_addr must be aligned to a 2-byte boundary if + size is 2 and to a 4-byte boundary if + size is 4. + + + + + R1--5. + + The ibm,read-pci-config call + of IOAs or functions which are not present or which + are not available to the caller must return + Success with all ones as the output + value. + + + + +
+ +
+ <emphasis>ibm,write-pci-config</emphasis> + + + + R1--1. + + For Platforms which may have greater than 256 PCI + Buses: RTAS must implement an + ibm,write-pci-config + call + using the argument call buffer defined by + . + + + Argument Call Buffer + <emphasis>ibm,write-pci-config</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,write-pci-config + + + + + + Number Inputs + + + + 5 + + + + + + Number Outputs + + + + 1 + + + + + + Config_addr + + + + Configuration Space Address + + + + + + PHB_Unit_ID_Hi + + + + Represents the most-significant 32-bits of the Unit ID of + the PHB that corresponds to the + config_addr + + + + + + PHB_Unit_ID_Low + + + + Represents the least-significant 32-bits of the Unit ID + of the PHB that corresponds to the + config_addr + + + + + + Size + + + + Size of Configuration Cycle + in bytes, + can be 1, 2, or 4 + + + + + + Value + + + + Value to be written to the location specified by the PHB + Unit ID and config_addr + + + + + Out + + + + Status + + + + 0: Success + -1: Hardware Error + -3: Parameter or device enablement error + + + + +
+ + + + + R1--2. + + The + ibm,write-pci-config call must store the value to the + configuration register which is at the location specified by the PHB Unit + ID and + config_addr in PCI configuration space. + + + + + R1--3. + + The ibm,write-pci-config call must perform a 1-byte, + 2-byte, or 4-byte configuration space write depending on the value of the + size input argument. + + + + + R1--4. + + The config_addr must be aligned to a 2-byte boundary if + size is 2 and to a 4-byte boundary if + size is 4. + + + + + R1--5. + + The ibm,write-pci-config call + of IOAs or functions which are not present or which + are not available to the caller must be ignored and a + Status of 0 (Success) must be returned. + + + + + R1--6. + + For the LPAR option: The + Status of -3 (Parameter or device enablement error) + must be returned if all the following are true: + + + + The OS attempts an + ibm,write-pci-config to enable Memory or I/O for an + IOA, without first calling + ibm,set-eeh-option to enable EEH for the IOA + + + + Enabling the IOA could expose other partitions to errors from + the partition which is enabling the IOA + + + + The hypervisor is + enforcing EEH mode + + + + + Platform Implementation Note: In Requirement + + , + cross-partition errors could + be caused due to error domains which are shared between the partitions. + However, it is acceptable to share error domains when the IOA and its + device driver and the partition's OS cannot (through error or + maliciously) cause errors which affect another partition. + + + + +
+ +
+ +
+ Operator Interfaces and Platform Control + The RTAS operator interface and platform control functions provide + the OS with the ability to perform platform services in a portable + manner. The RTAS operator interface provides the ability for the OS to + notify the user about OS events during boot, to notify the user of + abnormal events, and to obtain information from the platform. The + platform control functions give the OS the ability to obtain + platform-specific information and to control platform features. + These calls are all “best effort” calls. RTAS should + make its best effort to implement the intent of the call. If the Platform + Hardware does not implement some optional feature, it is permitted for + RTAS to either return an error, or to virtualize the service in some way + and return “Operation Succeeded.” + Software Implementation Notes: + + + + For example, a keyswitch + could be virtualized by storing a keyswitch value in + NVRAM and by providing a user interface to modify this value. The RTAS + call + get-sensor-state on the + keyswitch returns the value stored in NVRAM. + + + + If these services are only called prior to the use of any of the + underlying devices by the OS, for example, during boot time, or only + after the OS has finished using the devices, for example, during a crash, + then the OS can avoid mutual exclusion and sharing concerns. Otherwise, + synchronization per + , must be performed. + + + +
+ Op Panel Display + + + + R1--1. + + Platform Implementation: + All servers must + implement an operator panel display mechanism by supporting the + display-character RTAS call. + + Implementation Note: The operator display mechanism + in Requirement + may be a physical alphanumeric + display with a special purpose LCD device marked “used by + RTAS”, or it may be some other virtualized display which is + accessible through some method not defined by this architecture. + + + + + R1--2. + + Platform Implementation: Servers which provide + display-character must provide a line length of at + least 16 characters. + + + + + + Software Implementation Notes: + + + + + There are currently four uses for the op panel display. The + first is for display of an error code, if needed, from the + Built-In-Self-Test (BIST) or Power-On-Self-Test (POST). This display is + machine dependent. (These tests are executed prior to loading the OS or + the operation of OF. Any display requirements are handled within the + hardware.) The second is for progress indication during initialization + and boot. This display is four digits and is updated as boot proceeds. + The third is for display after a failure running diagnostics. In this + case, a service request number (SRN) is displayed along with a FRU + location code list of possible devices needing service. These numbers and + locations can be longer than four characters. The SRN may be over 12 + characters and a FRU location code list is one or more items, typically + three, of 2 to 32 characters. The fourth is a crash code from the OS + which is 12 characters indicating cause and dump status. + + + + The RTAS + set-indicator call with token #6 specifies 4 hex + digits. The + display-character call requires a minimum display + size of one line of 4 characters, but a larger display may be made known + to the OS using the “ibm,” extension properties defined in + . When the message to be + displayed is larger than the OS believes the display to be, the OS should + perform appropriate truncation, scrolling, or otherwise meaningfully + display the message using the platform’s display resource. + + + + Some servers implement a display larger than the default. For + these servers, the + “ibm,display-line-length” property and + the + “ibm,display-number-of-lines” property + are set appropriately. + + + + If the OS assumes the default display, the 2X16 display still + works. It appears to be working in the bottom line and scrolling through + the top line as long as only CR and LF are issued for control. The OF + device tree properties indicate what is supported. + + + +
+ +
+ Service Processor + A service processor is not a platform requirement. Larger servers + tend to be implemented with service processors. When implemented, the + service processor is not seen directly as a device by software. All of + its services which are visible to the OS, are abstracted with RTAS. The + service processor may support the operator panel, manage sensors and + indicators, run diagnostics, monitor the platform environment and save + error logs. There is clearly an interface between RTAS and the service + processor, but that interface is not intended to be used by the + OS. + The service processor, in those platforms which choose to use one, + is key in the initialization of the platform and has interfaces with the + OF code. It is also involved with VPD collection and NVRAM access during + initialization. It can also provide a serial port for a remote service + capability. The service processor is also a significantly slower + processor than the primary PA processor. Therefore, in the implementation + of RTAS functions which use the service processor, care should be taken + to avoid interlocks with the service processor which could significantly + impair performance. + +
+ Surveillance + Platforms which include a service processor have the needed + mechanism for a surveillance function; that is, the OS and the service + processor can monitor each other. For example, if the OS crashes or + hangs, or if the service processor has failures, a failure notification + could occur. Notification could also occur if the platform fails during + the boot process, or if it cannot complete a boot successfully. The + notification can be sent to a service center or to a customer + administrator, as determined by the customer setup of configuration + parameters. The firmware provides notification to the OS by reporting + exceptions through + event-scan. The service processor can provide + dial-out notification if the OS stops, or if a boot process fails. + In the implementation of surveillance, the service processor + monitors the OS by tracking the issuance of heartbeats generated by calls + to the + event-scan RTAS service. If a service processor + time-out occurs prior to receiving another heartbeat, an action based on + user defined call out policy occurs. This action could be to reboot, call + service or power-down. The policy may be different depending on whether + the time-out occurs during a boot process or during a period of normal OS + operation. The default policy and time-out period, kept in NVRAM, can be + changed from a service processor menu or from software. The platform can + be configured such that surveillance is either enabled or disabled + immediately after boot. After boot, temporary changes to the surveillance + state can be made by issuing a + set-indicator call to indicator 9000 (see + ). + The following system parameters define the default behavior of + surveillance mode (see also, + for more information about + these parameters and for their default values). + + + + The + sp-sen system parameter defines whether the default + state of surveillance by the service processor is enabled (=on) or + disabled (=off). + + + + The + sp-sti system parameter defines the period of time + (1-255 minutes) that the service processor should wait between heartbeats + from + event-scan. If the time-out period expires without + the service processor receiving another heartbeat, the service processor + initiates recovery and reporting actions as defined by the user. + + + + The + sp-sdel system parameter defines the period of time + (1-120 minutes) that the service processor should wait before starting + surveillance after control passes to the OS. This value is set to allow + enough time for the OS to boot and initialize to the point where it can + start calling + event-scan on a regular periodic basis. + + + + + Architecture Note: Surveillance times out if the + time of the parameter, + sp-sdel, plus the time of the parameter, + sp-sti, passes prior to receiving the first + heartbeat. In effect, the first + event-scan can be considered the signal for boot + complete. + The platform may perform surveillance on the service processor + using + event-scan to trigger checking as well as for + reporting any errors found. + Software Implementation Note: + The surveillance here is for keeping + an eye on the overall functioning of the OS. If a specific process gets + hung and the OS is still functioning, it is the responsibility of the OS + to detect and not the surveillance discussed here. + OF Implementation Note: + The OS is expected to call the + event-scan RTAS service (with the internal-errors + mask bit on) at the rate defined by the property + “rtas-event-scan-rate” in the OF device + tree. If an + “rtas-event-scan-rate” + of zero (0) + is placed in the OF device tree and surveillance is initialized as + ‘active’, a surveillance time-out occurs after the time-out + period since the heartbeats are triggered by the + event-scan call. If there is reason to operate with + the rate = 0, the default state of surveillance ( + sp-sen parameter in NVRAM) should be disabled, and + the surveillance sensor and indicator should not be placed in the OF + device tree. + + + + R1--1. + + Platform Implementation: The default surveillance + policy must be defined by the + sp-sen, + sp-sti and + sp-sdel system parameters, as set by the service + processor or by software. + + + + + R1--2. + + Platform Implementation: Heartbeats to the service + processor must only be sent as the result of a call to the + event-scan RTAS service with the + internal-errors bit (bit 0) set to 1 in the call + buffer + Event Mask parameter. + + + + + R1--3. + + Platform Implementation: In platforms which implement + surveillance, the + event-scan RTAS service may be called more than once + per minute, but the heartbeat to the service processor must be sent at + the rate of at least once per minute. + + + + + R1--4. + + Platform Implementation: In platforms which implement + surveillance, the + ibm,os-term RTAS call must be implemented. + + + + + + Software Note: Requirement + provides a mechanism for the OS + to release control of the platform without being aware of the state of + surveillance. With the definition of a default platform state for + surveillance, the OS may not be aware of the function, yet surveillance + may be used. Platforms may not have a dependency on the OS to turn off + surveillance during normal shutdown (a shutdown not including immediate + reboot). +
+ +
+ Surveillance on SMP Systems + Each running processor in an SMP system should be covered by + surveillance. The following requirements assure this coverage. + + + + R1--1. + + Each processor which is running, that + is, not stopped by the stop-self RTAS call or not stopped due to BIST + testing at bring-up, must issue the event-scan RTAS call. The rate of + issue is the + “rtas-event-scan-rate” times per minute + divided by the number of processors. This is the minimum rate. + + + + + R1--2. + + The system must allow for all + processors to cycle through their event-scan calls. The timeout period + for a surveillance event, which is + sp-sti, must be greater than n time t, where n is + the number of processors and t is the + “rtas-event-scan-rate”. + + + + + R1--3. + + The surveillance event must be signaled + if after the surveillance interval, + sp-sti, one or more processors has not issued an + event-scan call. + + + + + + Implementation Note: Care is required in the + assignment of the surveillance interval and the + “rtas-event-scan-rate” such that a + surveillance event is not signaled prematurely. The default values are + not meant for a system with a large number of processors. +
+ +
+ +
+ <emphasis>display-character</emphasis> + The + display-character function allows the display of both + alphabetic and numeric information. The display for this function + requires at least one line of four (4) characters. Also specified are the + control characters carriage-return (CR) (0x0D) and line-feed (LF) + (0x0A). + The following OF properties are defined in + : + + + + “ibm,display-line-length” + + + + “ibm,display-number-of-lines” + + + + “ibm,display-truncation-length” + + + + “ibm,form-feed” + + + + + + R1--1. + + If + display-character is implemented on a platform, the + property + “ibm,display-line-length” in the + /rtas node must be provided if greater than the + required minimum default of 4 characters. + + + + + R1--2. + + If + display-character is implemented on a platform, the + property + “ibm,display-number-of-lines” in the + /rtas node must be provided if greater than the + required minimum default of 1 line. + + + + + R1--3. + + If the + “ibm,display-number-of-lines” is greater + than one, the platform must support form-feed (FF) (0x0C). + + + + + R1--4. + + If form-feed is implemented, it must + clear the display and position the display pointer to line 1 column + 1. + + + + + R1--5. + + The platform must include the property + “ibm,form-feed” + in the + /rtas node. + + + + + R1--6. + + For the + display-character RTAS call, when the truncation + length as specified in the + “ibm,display-truncation-length” property, + when it exists, is less than the length of the line being displayed on + that particular line, then the firmware must truncate the requested line + to be displayed to the length specified in the + “ibm,display-truncation-length” property + for that line. + + + + + R1--7. + + For the + display-character RTAS call, when the truncation + length as specified in the + “ibm,display-truncation-length” property, + when it exists, is greater than the length specified of the line as + specified in + “ibm,display-line-length” then the + platform must provide a platform-dependent method of displaying the line + to the user. + + + + + R1--8. + + For platforms that use converged location + codes, the platform must provide scrolling for the + display-character RTAS call, on the second line of + the display, and must provide the + “ibm,display-truncation-length” property + and specify a truncation length of no less than 80 characters for that + line. + + Platform and Software Implementation Note: In + implementing Requirements + and + , it is permissible to have a + separate buffer for any of the lines of the display and not display that + line until a button is pressed. + The RTAS call display-character can be used by the OS to display + informative messages during boot, or to display error messages when an + error has occurred and the OS cannot depend on its display drivers. This + call is intended to display the alpha-numeric characters on an LCD panel, + graphics console, or attached tty. The precise implementation is platform + vendor specific. + + + + + R1--9. + + RTAS must implement a + display-character call using + the argument call buffer defined by + to place a character on the + output device. + + + + + R1--10. + + The OS must serialize all calls to + display-character with any other use of the + rtas-display-device. + + + Argument Call Buffer + <emphasis>display-character</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + display-character + + + + + + Number Inputs + + + + 1 + + + + + + Number Outputs + + + + 1 + + + + + + Value + + + + Character to be displayed + + + + + Out + + + + Status + + + + 0: Success + -1: Hardware error + -2: Device busy, try again later + + + + +
+ + + + + R1--11. + + If a physical + output device is used for the output of the RTAS + display-character call, then it must have at least + one line and 4 characters. + + + + + R1--12. + + Certain ASCII control characters must + have their normal meanings with respect to position on output devices + which are capable of cursor positioning. In particular, ^M (0x0D) must + position the cursor at column 0 in the current line, and ^J (0x0A) must + move the cursor to the next line. If on the bottom line, move to column 0 + and scroll old data off the top. + + + + + R1--13. + + The ASCII characters which must be + displayed are generally those coded from 0x20 to 0x7E as shown in + . SP indicates a space and ND + is not defined + + + Display ASCII Characters + + + + + + + + + + + + + + + + + + Hex + + + + + Disp + + + + + Hex + + + + + Disp + + + + + Hex + + + + + Disp + + + + + Hex + + + + + Disp + + + + + Hex + + + + + Disp + + + + + Hex + + + + + Disp + + + + + + + + 20 + + + SP + + + 30 + + + 0 + + + 40 + + + @ + + + 50 + + + P + + + 60 + + + ‘ + + + 70 + + + p + + + + + 21 + + + ! + + + 31 + + + 1 + + + 41 + + + A + + + 51 + + + Q + + + 61 + + + a + + + 71 + + + q + + + + + 22 + + + “ + + + 32 + + + 2 + + + 42 + + + B + + + 52 + + + R + + + 62 + + + b + + + 72 + + + r + + + + + 23 + + + # + + + 33 + + + 3 + + + 43 + + + C + + + 53 + + + S + + + 63 + + + c + + + 73 + + + s + + + + + 24 + + + $ + + + 34 + + + 4 + + + 44 + + + D + + + 54 + + + T + + + 64 + + + d + + + 74 + + + t + + + + + 25 + + + % + + + 35 + + + 5 + + + 45 + + + E + + + 55 + + + U + + + 65 + + + e + + + 75 + + + u + + + + + 26 + + + & + + + 36 + + + 6 + + + 46 + + + F + + + 56 + + + V + + + 66 + + + f + + + 76 + + + v + + + + + 27 + + + ‘ + + + 37 + + + 7 + + + 47 + + + G + + + 57 + + + W + + + 67 + + + g + + + 77 + + + w + + + + + 28 + + + ( + + + 38 + + + 8 + + + 48 + + + H + + + 58 + + + X + + + 68 + + + h + + + 78 + + + x + + + + + 29 + + + ) + + + 39 + + + 9 + + + 49 + + + I + + + 59 + + + Y + + + 69 + + + i + + + 79 + + + y + + + + + 2A + + + * + + + 3A + + + : + + + 4A + + + J + + + 5A + + + Z + + + 6A + + + j + + + 7A + + + z + + + + + 2B + + + + + + + 3B + + + ; + + + 4B + + + K + + + 5B + + + [ + + + 6B + + + k + + + 7B + + + { + + + + + 2C + + + , + + + 3C + + + < + + + 4C + + + L + + + 5C + + + \ + + + 6C + + + l + + + 7C + + + | + + + + + 2D + + + - + + + 3D + + + = + + + 4D + + + M + + + 5D + + + ] + + + 6D + + + m + + + 7D + + + } + + + + + 2E + + + . + + + 3E + + + > + + + 4E + + + N + + + 5E + + + ^ + + + 6E + + + n + + + 7E + + + ~ + + + + + 2F + + + / + + + 3F + + + ? + + + 4F + + + O + + + 5F + + + _ + + + 6F + + + o + + + 7F + + + ND + + + + +
+ Software Implementation Note: Care should be taken in using the + full character set for all systems as some characters may not be + available or may display in a different fashion. For instance, the + currency symbol, $ (0x24), may be modified to a national currency symbol. + Other currently known differences occur for the reverse slant, \ (0x5C), + and the tilde, ~(0x7E). + + + + + R1--14. + + RTAS must not + output characters to the + rtas-display-device except for explicit calls from + the OS to the + display-character function except for the following + conditions. + + + + The rtas-display-device is marked + “used-by-rtas”. + + + + The RTAS call is + power-off, ibm,power-off-ups, set-power-level + (0,0), or + system-reboot. + + + + + + + + + Software Implementation Notes: + + + + + RTAS should try to produce output to the user. This could be to + the system console, to an attached terminal, or to some other device. It + could be implemented using a diagnostic processor or network. RTAS could + also implement this call by storing the messages in a buffer in NVRAM so + the user could determine the reason for a crash upon reboot. + + + + This call modifies the registers associated with the + rtas-display-device. The OS may also access this + device, being aware that calls to + display-character change the state of the + device. + + + +
+ +
+ <emphasis>set-indicator</emphasis> + The RTAS + set-indicator function provides the OS with an + abstraction for controlling various lights, indicators, and other + resources on a platform. If multiple indicators of a given type are + provided by the platform, this function permits addressing them + individually. + + + + R1--1. + + RTAS must implement a + set-indicator call which sets the value of the + indicator of type + Indicator and index + Indicator-index using the argument call buffer + defined by + and indicator types defined by + . + + + Argument Call Buffer + <emphasis>set-indicator</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + set-indicator + + + + + + Number Inputs + + + + 3 + + + + + + Number Outputs + + + + 1 + + + + + + Indicator + + + + Token defining the type of indicator + + + + + + Indicator-index + + + + Index of specific indicator (0, 1,...) + + + + + + State + + + + Desired new state + + + + + Out + + + + Status + + + + 990x: Extended Delay + 0: Success + -1: Hardware Error + -2: Hardware busy, try again later + -3: No such indicator implemented + -9000: Multi-level isolation error + -9001: Valid outstanding translation + + + + +
+ + + + + R1--2. + + For indicators in the + “rtas-indicators” property, the indices + for indicators must start at zero (0) and increment sequentially up to + the maximum index; that is, all of the integers and only those integers + from 0 to the maximum index are valid. + + Architecture Note: Indicator indices that are + obtained via the + ibm,get-indices RTAS call are not necessarily + contiguous (that is, any of the indices between 0 and the + maxindex, inclusive, may be missing). + + + + + R1--3. + + Of the indicator types defined by + , RTAS must implement at least + Tone Frequency and Tone Volume. + + + + + R1--4. + + The + set-indicator RTAS call must not return a busy + indication (-2 or 990x) for any indicator in + which is marked with a + “yes” in the “Fast?” column of that table. + + + + + R1--5. + + The platform may, but is not required to, + turn off a tone automatically after 5 minutes or more duration (that is, + automatically set the Tone Volume to zero), and therefore a user of the + Tone must call + set-indicator Tone Volume with a volume value of + non-zero, if a tone is to be sustained longer than 5 minutes, and if the + platform is going to automatically terminate the tone, the platform must + reset its automatic turn-off timer when it receives a + set-indicator call for the Tone Volume with a + non-zero tone volume value. + + + + + + Defined Indicators + + + + + + + + + + + + + + Indicator Name + + + + + Token Value + + + + + Defined Values + + + + + Default Value + + + + + Fast? + + + + + Required? + + + + + <vendor> + + Values in the “<vendor>” column are + used to replace the “ + <vendor>” field of the + “<vendor>,indicator-<token>” + property, when that property is + presented. See Requirement + . + + + + + + Examples/Comments + + + + + + + + Tone Frequency + + + 1 + + + Unsigned Integer + (units are Hz) + + + 1000 + + + yes + + + When tone is required. See Requirement + . + + + ibm + + + Generate an audible tone using the tone generator + hardware. RTAS selects the closest implemented audible + frequency to the requested value. + + + + + Tone Volume + + + 2 + + + 0-100 (units are percent), + 0 = OFF + + + 0 + + + yes + + + When tone is required. See Requirement + . + + + ibm + + + Set the percentage of full volume of the tone generator + output, scaled approximately logarithmically. RTAS should + select the closest implemented volume for values between zero + (off) and 100 (full on). + + + + + - + + + 3-6 + + + - + + + - + + + - + + + - + + + - + + + Reserved. + + + + + - + + + 7 + + + - + + + - + + + - + + + - + + + - + + + Reserved. Was (deprecated) Battery Warning Time. + + + + + - + + + 8 + + + - + + + - + + + - + + + - + + + - + + + Reserved. Was (deprecated) Condition Cycle + Request. + + + + + Surveillance + + + 9000 + + + 0-disabled + 1-255-timeout + + + sp-sti + + + yes + + + When the platform implements the surveillance + function. + + + ibm + + + Initialized with value from the sp-sti system + parameter. + + + + + Isolation-state + + + 9001 + + + Isolate = 0 + Unisolate = 1 + + + 1 + + + no + + + For all DR options + + + - + + + Isolate refers to the DR action to logically disconnect + from the platform and/or OS (for example, for PCI, isolate from + the bus and from the OS). See + for more + details. + + + + + DR + + + 9002 + + + Inactive = 0 + Active = 1 + Identify = 2 + Action = 3 + + + 0 if Inactive + 1 if Active + + + no + + + For all DR options + + + - + + + Indicator index may refer to a single indicator that + combines Power/Active indicator and Identify/Action indications + or just an Identify/Action indicator. Identify and Action may + map to the same visual state (for example, the same blink + rate). See + and + for more + information. + + + + + Allocation-state + + + 9003 + + + unusable (0) + usable (1) + exchange (2) + recover (3) + + +   + + + no + + + For all DR options + + + - + + + Allows an OS image to assign (usable, exchange, or + recover) resources from the firmware or, release resources from + the OS to the firmware. See + for more + details. + + + + + - + + + 9004 + + + - + + + - + + + - + + + - + + + - + + + Reserved. + + + + + Global Interrupt Queue Control + + + 9005 + + + Disable = 0 + Enable = 1 + + + 1 + + + yes + + + See Requirement + . + + + ibm + + + Enable and Disable the processor as Global Interrupt + Queue Server + + + + + Error Log + or + FRU Fault + + + 9006 + + + Normal (off) = 0 + Fault (on) = 1 + + + 0 + + + no + + + Yes + See + . + + + ibm + + + This indicator is combined with the Identify indicator + for the Primary Enclosure drawer/enclosure (that is, is the + same physical indicator). Off indicates that the system is + working normally. On indicates that the system hardware, + firmware and/or diagnostics detected a fault (failure) in the + system or a partition requires operator intervention for + another reason. The Error Log indicator is located only on the + Primary Enclosure. See + and + for more + information. + + + + + Identify (Locate) + + + 9007 + + + Normal (off) = 0 + Identify (blink) = 1 + + + 0 + + + no + + + Yes + See + . + + + ibm + + + Note that a 9002 indicator also has an Identify state, + and in the case where the 9002 indicator is implemented with + two physical indicators (one for Power and one for + Identify/Action), the same physical indicator must be used for + both a 9002 Identify/Action indicator and 9007 Identify + indicator. This architecture does not specify any mechanism for + protecting against the simultaneous use by the user of an + indicator that is both a 9002 and 9007 indicator, nor does it + protect against the use of multiple 9007 indicators + simultaneously or multiple uses of the same 9007 indicator + simultaneously. See + and + for more + information. + + + + + - + + + 9008 + + + - + + + - + + + - + + + - + + + - + + + Reserved. + + + + + - + + + 9009 + + + - + + + - + + + - + + + - + + + - + + + Reserved. + + + + + Vendor Specific + + + 9100-9999 + + +   + + +   + + +   + + +   + + + <vendor> + + The vendor specific company representation, as used on + other OF properties specified by that vendor. + + + + Indicator values reserved for platform vendor use. + + + + +
+ +
+ Indicators + + +
+ Indicator 9000 Surveillance + An indicator is defined with the token value 9000 to allow + temporary modification of the state of the surveillance function (further + described in + ). + To enable monitoring of heartbeats from the + event-scan RTAS call, the surveillance indicator is + set with a value of 1 to 255, indicating the number of minutes for the + surveillance time-out value. If monitoring is already enabled, the + time-out value can be modified by setting this indicator. To disable + monitoring, the surveillance indicator should be set to a value of zero + (0). The + set-indicator call is used to modify the state of + surveillance (overriding the default system parameter values) only for + the current session. The surveillance state returns to the default values + when the system is rebooted. + The default surveillance configuration may be modified by changing + the system parameters. For more information on these parameters, refer to + + . + + + + R1--1. + + Platforms with the surveillance + function must implement a sensor and an indicator, with the token value + of 9000, with defined state input values of on (= 1-255, which enables + surveillance with specified time-out value in minutes) and off (= 0, + which disables surveillance). + + + + + + Firmware Implementation Note: The requirement above + results in the creation of the properties + “ibm,indicator-9000” and + “ibm,sensor-9000” in the + /rtas node. + + Hardware Implementation Note: The action that the + service processor takes in the case of a timeout is determined by the + configuration setup policy in the system parameters. +
+ +
+ Indicator 9005 Global Interrupt Queue Control + The 9005 indicator controls the global interrupt server queue logic + of the interrupt presentation controllers for the processor making the + call (Available Processor Mask (APM) for the PowerPC interrupt + presentation controller). This is used when bringing a processor online + and taking a processor offline. + + + + R1--1. + + Platforms that + allow processors to be brought online or be taken offline dynamically + must implement the global interrupt queue control indicator with a value + of 9005 as specified in + . + + + + + R1--2. + + The index value for global interrupt + queue control indicator (9005) must be + (2 + ibm,interruptserver#-size) - 1 - the + gserver# of the global server to be controlled as + given in the + + “ibm,ppc-interrupt-gserver#s” property. + + + + +
+ +
+ +
+ +
+ <emphasis>get-sensor-state</emphasis> + The RTAS call + get-sensor-state is used by the OS to read the + current state of various sensors on any Platform. If multiple sensors of + a given type are provided by the platform, this function permits + addressing them individually. + + + + R1--1. + + RTAS must implement a + get-sensor-state call which + reads the value of the sensor of type + Sensor which has index + Sensor-index using the argument call buffer defined + by + and the sensor types defined by + + . + + + + + R1--2. + + If a platform tests sensor values against + limits, then RTAS must return the result of these tests using the + Status output parameter. + + + <emphasis>get-sensor-state</emphasis> Argument Call Buffer + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for get-sensor-state + + + + + + Number Inputs + + + + 2 + + + + + + Number Outputs + + + + 2 + + + + + + Sensor + + + + Token defining the sensor type + + + + + + Sensor-index + + + + Index of specific sensor (0, 1,...) + + + + + Out + + + + Status + + + + 990x: Extended Delay where x is a number 0-5 (see text + below) + 13: Sensor value >= Critical high + 12: Sensor value >= Warning high + 11: Sensor value normal + 10: Sensor value <= Warning low + 9: Sensor value <= Critical low + 0: Success + -1: Hardware Error + -2: Hardware Busy, Try again later + -3: No such sensor implemented + -9000: DR Entity isolated ( + ) + + + + +   + + + + State + + + + Current value as defined in the Defined Values column of + . + + + + +
+ + Software Implementation Note: When the 990x + Status is returned, it is suggested that software + delay for 10 raised to the x milliseconds (where x is the last digit of + the 990x return code), before calling + get-sensor-state again. However, software may issue + the + get-sensor-state call again either earlier or later + than this. + + + + + R1--3. + + For sensors in the + “rtas-sensors” property, the indices for + sensors must start at zero (0) and increment sequentially up to the + maximum index; that is, all of the integers and only those integers from + 0 to the maximum index are valid. + + Architecture Note: Sensor indices that are obtained + via the + ibm,get-indices RTAS call are not necessarily + contiguous (that is, any of the indices between 0 and the + maxindex, inclusive, may be missing). + + + + + R1--4. + + The get-sensor RTAS call must not return a busy + indication (-2 or 990x) for any indicator in + which is marked with a + “yes” in the “Fast?” column of that table. + + + + + + Hardware Implementation Note: Some platforms may + compare the value of environmental sensors (such as the Battery Voltage + or Thermal Sensor) to some limits. When the value of the sensor meets or + exceeds a limit, the platform may take some action. RTAS makes the OS + aware of the relationship of the sensor values to the limit by using the + Status code to return this information. + + Software and Hardware Implementation Notes: The + meaning of these limits is as follows: + + + + Critical High - The sensor value is greater than or equal to this + limit. The platform may take some action and may initiate an EPOW (see + ). The OS may take some action + to correct this situation or to perform an orderly shutdown. + + + + Warning High - The sensor value is greater than or equal to this + limit, but less than the critical high limit. The platform may initiate a + warning EPOW. The OS may take some action to bring this reading back into + the normal range. + + + + Normal - RTAS is aware of the limits and the value is within + these operating limits. + + + + Warning Low - The sensor value is less than or equal to this + limit, but greater than the critical low limit. The platform may initiate + a warning EPOW. The OS may take some action to bring this reading back + into the normal range. + + + + Critical Low - The sensor value is less than or equal to this + limit. The platform may take some action and may initiate an EPOW. The OS + may take some action to correct this situation or to perform an orderly + shutdown. + + Where: + + + + A ‘critical’ state is defined as a condition where + the sensor value of the measured item indicates that it is outside the + allowable operating parameters of the system, and that a failure is + imminent unless some immediate action is taken. + + + + A ‘warning’ state is defined as a condition where the + sensor value of the measured item indicates that it is outside the + expected operating parameters for normal operation, but has not yet + reached a critical state. The variance is significant enough that either + system software or an operator may want to take some action to bring the + parameter back into the normal range. + + + + + Platform Implementation Note: The existence of this + sensor state reporting capability should not be construed as a + requirement to have any limits on sensors or to always have all four + limits. + + + Defined Sensors + + + + + + + + + + + + + Sensor Name + + + + + Token Value + + + + + Defined Values + + + + + Fast? + + + + + Required? + + + + + <vendor> + + Values in the “<vendor>” column are + used to replace the “ + <vendor>” field of the + “<vendor>,sensor-<token>” + property, when that property is presented. See Requirement + . + + + + + + Description + + + + + + + + Key Switch + + + 1 + + + Off (0), + Normal (1), + Secure (2), + Maintenance (3) + + + yes + + + No + + + ibm + + + Key switch modes are tied to OS security policy. + Suggested meanings: Maintenance mode permits booting from + floppy or other external, non-secure media. Normal mode permits + boot from any attached device. Secure mode permits no manual + choice of boot device, and may restrict available functionality + which is accessed from the main operator station. Off + completely disables the system. + + + + + - + + + 2 + + + - + + + - + + + - + + + - + + + Reserved. + + + + + Thermal + + + 3 + + + Temperature + (in Degrees Celsius) + + + no + + + No + + + ibm + + + If implemented, returns the internal temperature of the + specified thermal sensor. + + + + + - + + + 4 + + + - + + + - + + + - + + + - + + + Reserved. Was (deprecated) Lid Status. + + + + + - + + + 5 + + + - + + + - + + + - + + + - + + + Reserved. + + + + + - + + + 6 + + + - + + + - + + + - + + + - + + + Reserved. Was (deprecated) Current battery output + voltage. + + + + + - + + + 7 + + + - + + + - + + + - + + + - + + + Reserved. Was (deprecated) Battery Capacity + Remaining. + + + + + - + + + 8 + + + - + + + - + + + - + + + - + + + Reserved. Was (deprecated) Battery Capacity + Percentage. + + + + + Environmental and + Power State (EPOW) + + + 9 + + + EPOW_Reset(0) + Warn_Cooling(1) + Warn_Power(2) + System_Shutdown(3) + System_Halt(4) + EPOW_Main_Enclosure(5) + EPOW_Power_Off(7) + + + yes + + + Yes + + + ibm + + + RTAS assessment of the environment and power state of the + platform. + + + + + - + + + 10 + + + - + + + - + + + - + + + - + + + Reserved. Was (deprecated) Battery Condition Cycle + State. + + + + + - + + + 11 + + + - + + + - + + + - + + + - + + + Reserved. Was (deprecated) Battery Charging State. + + + + + Surveillance + + + 9000 + + + 1-255 and 0 + + + yes + + + When the platform implements the surveillance + function + + + ibm + + + Current state of surveillance. + + + + + Fan speed + + + 9001 + + + fan - rpm + + + no + + + No + + + ibm + + +   + + + + + Voltage + + + 9002 + + + voltage - mv + + + no + + + No + + + ibm + + +   + + + + + DR-entity-sense + + + 9003 + + + DR connector empty = 0 + DR entity present = 1 + DR entity unusable (2) + DR entity available for exchange (3) + DR entity available for recovery (4) + + + no + + + For all DR options + + + - + + + Used in Dynamic Reconfiguration operations to determine + if connector is available and whether the user performed a + particular DR operation correctly. See + and + . + + + + + Power Supply + + + 9004 + + +   + + + no + + + No + + + ibm + + + Sense presence and status of power supplies. + + + + + Global Interrupt Queue Control + + + 9005 + + + Disabled = 0 + Enabled = 1 + + + yes + + + See Requirement + . + + + ibm + + + Global interrupt queue server control state. + + + + + Error Log + or + FRU Fault + + + 9006 + + + Normal (off) = 0 + Fault (on) = 1 + + + no + + + Yes + See + . + + + ibm + + + Off indicates that the system is working normally. + On indicates that the system hardware, firmware and/or + diagnostics detected a fault in the system. + + + + + Identify + + + 9007 + + + Normal (off) = 0 + Identify (blink) = 1 + + + no + + + Yes + See + . + + + ibm + + + Identify (locate) indicator (FRU, connector, or + drawer/unit). + Off is the default State. + On indicates the Identify State. + + + + + - + + + 9008 + + + - + + + - + + + - + + + ibm + + + Reserved. + + + + + - + + + 9009 + + + - + + + - + + + - + + + ibm + + + Reserved. + + + + + Vendor Specific + + + 9100-9999 + + +   + + +   + + +   + + + <vendor> + + The vendor specific company representation, as used on + other OF properties specified by that vendor. + + + + Reserved for use by platform vendors. + + + + +
+ +
+ Sensors + The current state of surveillance, as described in + , is queried with a call to + get-sensor-state with a token value of 9000. Fan + speed is queried with the token value of 9001 and an index specifying the + desired fan. Similarly, voltage is sensed with a token value of 9002 and + an index specifying the desired voltage source. + + + + R1--1. + + Platforms which implement the + surveillance function must implement a single defined RTAS sensor with + the token value of 9000, which returns values of on (= 1-255 minutes) and + off (= 0) to show the current state of surveillance during this + session. + + + + + R1--2. + + Platforms with software visible fan + speed sensors must implement them as defined RTAS sensors with the token + value of 9001, which returns a sensor value in revolutions per minute + (RPM). + + + + + R1--3. + + Platforms with software visible voltage + sensors must implement them as defined RTAS sensors with the token value + of 9002, which returns a sensor value in millivolts. + + + + + Hardware Implementation Note: + The notion of a delay, due to the + sensor data acquisition time, may make it desirable to cache sensor data + to avoid interlocking with the service processor. + Software Implementation Note: + Software should not assume that + sensor data returned is a real time reading. + +
+ Example Implementation of Sensors + An example implementation of a platform with a service processor + and four fans and four voltage sensors is represented by the paired + integers ( + token maxindex) in the OF device tree as shown in + . + + + Example - Contents of + <emphasis role="bold"><literal>“rtas-sensors”</literal></emphasis> property + + + + + + + + token + + + + + maxindex + + + + + + + + + (Any sensors withStandardSensor + Tokens)... + + + + + (Associated maxindex + values)... + + + + + + 9000 (surveillance) + + + 0000 + + + + + 9001 (fan-speed) + + + 0003 + + + + + 9002 (voltage) + + + 0003 + + + + +
+ This requires sensors such as those shown in + . + + + Example - Sensor Definitions + + + + + + + + + + sensor + + + + + token + + + + + index + + + + + value + + + + + + + + surveillance + + + 9000 + + + 0000 + + + 0 / 1-255 + + + + + fan#1 fan speed + + + 9001 + + + 0000 + + + fan rpm + + + + + fan#2 fan speed + + + 9001 + + + 0001 + + + fan rpm + + + + + fan#3 fan speed + + + 9001 + + + 0002 + + + fan rpm + + + + + fan#4 fan speed + + + 9001 + + + 0003 + + + fan rpm + + + + + voltage-level #1 + + + 9002 + + + 0000 + + + voltage - mv + + + + + voltage-level #2 + + + 9002 + + + 0001 + + + voltage - mv + + + + + voltage-level #3 + + + 9002 + + + 0002 + + + voltage - mv + + + + + voltage-level #4 + + + 9002 + + + 0003 + + + voltage - mv + + + + +
+ In addition, the properties + “ibm,sensor-9000”, + “ibm,sensor-9001” and + “ibm,sensor-9002” in the + /rtas node that each contain an array of strings. + Each entry in the array contains the location code for the matching + sensor. For example, the first entry of + “ibm,sensor-9001” contains the location + code for fan#1. Location codes are shown in + . Of course, since it is an + abstracted sensor, the entry for + “ibm,sensor-9000” is NULL. +
+ +
+ Power Supply Sensors + + + + R1--1. + + Platforms with multiple software + visible power supply sensors must implement them as defined RTAS sensors + with the token value of 9004, which returns the values defined in + . + + + + + + + Power Supply Sensor Values + + + + + + + + Value + + + + + Status + + + + + + + + 0 + + + Not present + + + + + 1 + + + Present and Not operational + + + + + 2 + + + Status unknown + + + + + 3 + + + Present and operational + + + + +
+ For static 9004 sensors, the maxindex in the + “rtas-sensors” property for the token + 9004 indicates the number of power supplies supported by the platform. In + this case, the property + “ibm,sensor-9004” in the + /rtas node contains the location code for each + index. + For dynamic 9004 sensors, the platform provides the information + about the 9004 indicators as it would for other dynamic sensors. That is, + the platform does not provide the + “ibm,sensor-9004” property and instead + provides the 9004 location code information through the + ibm,get-indices RTAS call, and if the + ibm,get-indices RTAS call returns an index of all-1's + for a 9004 indicator, then the + ibm,get-dynamic-sensor-state RTAS call is used to get + the sensor state, instead of the + get-sensor RTAS call. +
+ +
+ Environmental Sensors + + + + R1--1. + + Platforms which want to allow an + application to analyze their environmental sensors must provide the + property + “ibm,environmental-sensors” in the + /rtas node (see + ). + + + + + The values for this property is a list of integers that are the + token values (token) for the defined environmental sensors and the number + of sensors (maxindex) for that token which are implemented on the + platform. + Architecture Note: + When a sensor is in the + “ibm,environmental-sensors” property and + when the sensor token indices are obtained via the + ibm,get-indices RTAS call, the indices may not be + contiguous for that sensor token (that is, any of the indices between 0 + and the maxindex, inclusive, may be missing). +
+ +
+ Sensor 9005 Global Interrupt Queue Control + State + The 9005 sensor reports the state of the global interrupt server + queue logic of the interrupt presentation controller for the specific + processor making the call (Available Processor Mask (APM) for the PowerPC + interrupt presentation controller). This is used when varying the + processor on and off line. + + + + R1--1. + + Platforms that allow processors to be + brought online or be taken offline dynamically must implement the global + interrupt queue control sensor with a value of 9005 as specified in + . + + + + + R1--2. + + RThe index value for global interrupt + queue control state sensor (9005) must be + (2 + ibm,interrupt-server#-size) - 1- the gserver# of the + global queue to be sensed as given in the + + “ibm,ppc-interrupt-gserver#s” property. + + + + + + Note: on platforms that do not report + “ibm,interrupt-server#-size” property, + the assumed value of the size of the interrupt server number is 8. +
+ +
+ +
+ +
+ +
+ Power Control + + +
+ <emphasis>set-power-level</emphasis> + This RTAS call is used to set the power level of a power domain to + either on or off. + + + + R1--1. + + RTAS must implement the + set-power-level call using the argument call buffer + defined by + . + + + Argument Call Buffer + <emphasis>set-power-level</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + set-power-level + + + + + + Number Inputs + + + + 2 + + + + + + Number Outputs + + + + 2 + + + + + + Power_domain + + + + Token defining the power domain + + + + + + Level + + + + Token for the desired level for this domain + + + + + Out + + + + Status + + + + 0: Success + -1: Hardware Error + -2: Busy, Try again later + 990x:Extended Delay + where x is a number 0-5 (see text below) + + + + + + Actual_level + + + + The power level actually set + + + + +
+ + + + + R1--2. + + Power_domain must be a power domain identified in the + OF device tree. + + + + + R1--3. + + Level must be 100 for full power and 0 for + off. + + + + + R1--4. + + The set-power-level call + must return the power level actually set in the + Actual_level output parameter. + Software Implementation Notes: + + + + The set-power-level(0,0) call, if implemented, removes power + from the root domain, turning off power to all domains. The external + events which can turn power back on are platform specific. The RTAS + primitive power-off also removes power from the system, but permits + specifying the events which can turn power back on. + + + + The implemented values for the + Level parameter for each power domain are defined in + the OF device tree. + + + + + + + R1--5. + + The set-power-level RTAS call, when implemented, must + return either a -2 or a 990x return code if the + set-power-level operation specified in the RTAS call + is going to exceed 1 millisecond in duration (where value of x gives a + hint as to the duration of the busy; see text). + + + + + A single + set-power-level operation may require an extended + period of time for execution. Following the initiation of the hardware + operation to change the power level, if the + set-power-level call returns prior to successful + completion of the operation, the call returns either a + Status code of -2 or 990x. A + Status code of -2 indicates that RTAS may be capable + of doing useful processing immediately. A + Status code of 990x indicates that the platform + requires an extended period of time, and hints at how much time is + required. Neither the 990x nor the -2 + Status codes implies that the platform has initiated + the operation, but it is expected that the 990x + Status is used only if the operation had been + initiated. + When the 990x + Status is returned, it is suggested that software + delay for 10 raised to the x milliseconds (where x is the last digit of + the 990x return code), before calling + set-power-level with the same power domain token. + However, software may issue the + set-power-level call again either earlier or later + than this. + Software Implementation Note: + In Requirement + , a return code of -2 or 990x + may either mean that the operation was initiated but not completed, or + may mean that the operation was not initiated at all. + Firmware Implementation Notes: + + + + If the RTAS initiates and returns before successful completion + of the operation, then it needs to handle the split of a + set-power-level operation across multiple + calls. + + + + It is the firmware’s responsibility to not return a + Status of 0 (success) until the operation is + complete, and that may require performing an operation such as a delay + operation or querying the hardware for power good status. In the former + case, the firmware needs to save state between the calls to the same + power domain number, until the operation is complete. + + + + The + set-power-level RTAS call may be called to set the + power level of other power domains after the initiation to other domains + and before the operation to those other domains are complete. If + necessary, the + set-power-level call may return a -2 or 990x + Status to those calls without initiating the + operation, if multiple simultaneous operations are not feasible. + + + +
+ +
+ <emphasis>get-power-level</emphasis> + + + + R1--1. + + RTAS must implement the + get-power-level call using the argument call buffer + defined by + . + + + Argument Call Buffer + <emphasis>get-power-level</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + get-power-level + + + + + + Number Inputs + + + + 1 + + + + + + Number Outputs + + + + 2 + + + + + + Power_domain + + + + Token defining the power domain + + + + + Out + + + + Status + + + + 0: Success + -1: Hardware Error + -2: Busy, try again later + -3: Can’t determine current level + + + + + + Level + + + + The current power level for this domain + + + + +
+ + + + + R1--2. + + Power_domain must be a power domain identified in the + OF device tree. + Software Implementation Note: The + get-power-level call only returns information about + power levels whose state is readable in hardware. It does not need to + remember the last set state and return that value. + + + + +
+ +
+ <emphasis>power-off</emphasis> + This primitive turns power off on a system which is equipped to + perform a software-controlled power off function. + + + + R1--1. + + If software controlled power-off hardware is + present, the + power-off function must turn off power to the + platform, using the argument call buffer described in + . + + + <emphasis>power-off</emphasis> Argument Call Buffer + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + power-off + + + + + + Number Inputs + + + + 2 + + + + + + Number Outputs + + + + 1 + + + + + + Power_on_mask_hi + + + + Mask of events that can cause a power on event - event + mask values [0:31] (right-justified if the cell size is 64 + bits) + + + + + + Power_on_mask_lo + + + + Mask of events that can cause a power on event - event + mask values [32:63] (right-justified if the cell size is 64 + bits) + + + + + Out + + + + Status + + + + On successful operation, does not return + -1: Hardware error + + + + +
+ + + + + R1--2. + + If software controlled power-off hardware is + present, + Power_on_mask, which is passed in two parts to permit + a possible 64 events even on 32-bit implementations, + must be a bit mask of power on triggers, or if the + “power-on-triggers” property is absent + from the + /rtas node, a value of 0 must be used for + Power_on_mask_hi and + Power_on_mask_lo. + + + + + R1--3. + + Platforms must omit the + “power-on-triggers” property from the + /rtas node. + + + Implementation Note: The power on triggers, which + were removed from this architecture, are documented in the + , for legacy reasons. + + + Defined Power On Triggers + + + + + + + + Bit + + + + + Event + + + + + + + + 0 + + + Power Switch On + + + + + 2 + + + Lid Open + + + + + 5 + + + Wake Button + + + + + 8 + + + Switch to Battery + + + + + 9 + + + Switch to AC + + + + + 10 + + + Keyboard or mouse activity + + + + + 12 + + + Enclosure Closed + + + + + 13 + + + Ring Indicate + + + + + 14 + + + LAN Attention + + + + + 15 + + + Time Alarm + + + + + 16 + + + Configuration change + + + + + 17 + + + Service Processor + + + + +
+ + + + + R1--4. + + For the System Parameters option: If software + controlled power-off hardware is present, the power-off function must + prevent reboot in the event of a later external power recovery with the + platform_auto_power_restart system parameter enabled. + + + + +
+ +
+ <emphasis>ibm,power-off-ups</emphasis> + This RTAS call manages the system power-off function in systems + which may have power backed up with an Uninterruptible Power Supply + (UPS). + + + + R1--1. + + For platforms that support a platform + controlled Uninterruptible Power Supply (UPS), the + ibm,power-off-ups function must be implemented, + whether a platform controlled UPS is present or not, using the argument + call buffer described in + . + + + Argument Call Buffer + <emphasis>ibm,power-off-ups</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,power-off-ups + + + + + + Number Inputs + + + + 0 + + + + + + Number Outputs + + + + 1 + + + + + Out + + + + Status + + + + On successful operation, does not return + -1: Hardware error + + + + +
+ + + + + R1--2. + + If a platform controlled UPS is present, + then the + ibm,power-off-ups RTAS call must turn off system + power while enabling platform auto restart upon restoration of system + power, according to the platform_auto_power_restart policy described in + , and must not return, + otherwise, the call must not turn off system power and must not + return. + + + + + R1--3. + + If a platform controlled UPS is not + present, then the + ibm,power-off-ups RTAS call must turn off system + power while enabling platform auto restart upon restoration of system + power, according to the platform_auto_power_restart policy described in + , and must not return, + otherwise, the call must not turn off system power and must not + return. + + + + + + Software Implementation Notes: + + + + + Supporting + ibm,power-off-ups, allows a system to be shutdown + due to a report that the system was running under UPS power for systems + with a platform managed UPS. As opposed to + power-off, + ibm,power-off-ups, permits the operating system to + be restarted when power is restored after a loss of external + power. + + + + The report that a system needs to be shutdown due to running + under a UPS would be given by the platform as an EPOW event with EPOW + event modifier being given as, 0x02 = Loss of utility power, system is + running on UPS/Battery, as described in section + . + + + + If the RTAS + ibm,power-off-ups call is supported by the platform, + it will also allow a shutdown with a subsequent restart when power is + restored for systems running with a UPS that is not under platform + control. This presumes that the OS has some external means of recognizing + when running under UPS power to initiate the + ibm,power-off-ups call. + + + +
+ +
+ +
+ Reboot and Flash Update Calls + During execution, it may become necessary to shut down processing + and reboot the system in a new mode. For example, a different OS level + may need to be loaded, or the same OS may need to be rebooted with + different settings of System Environment Variables. + +
+ <emphasis>system-reboot</emphasis> + + + + R1--1. + + RTAS must implement a + system-reboot call which resets all processors and + all attached devices. After reset, the system must be booted with the + current settings of the System Environment Variables (refer to + for more information). + + + + + R1--2. + + The RTAS + system-reboot call must be implemented using the + argument call buffer defined by + . + + + Argument Call Buffer + <emphasis>system-reboot</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + system-reboot + + + + + + Number Inputs + + + + 0 + + + + + + Number Outputs + + + + 1 + + + + + Out + + + + Status + + + + On successful operation, does not return + -1: Hardware error + + + + +
+ + + + + Hardware Implementation Note: + The platform must be able to perform + a system reset and reboot. On a multiprocessor system, this should be a + hard reset to the processors. +
+ +
+ <emphasis>ibm,update-flash-64-and-reboot</emphasis> + The + ibm,update-flash-64-and-reboot function is described + in this section. It does not return to the OS if successful. This call + supports RTAS instantiated in 32 bit mode to access storage at addresses + above 4GB. In an exception to the LPAR Requirement + this call supports block lists + being outside of the Real Mode Area (RMA) as long as the initial block + list is at an address below the limits of the cell size of the + Block_list argument. + + + + R1--1. + + The argument call buffer for the + ibm,update-flash-64-and-reboot RTAS call must + correspond to the definition in + . + + + Argument Call Buffer + <emphasis>ibm,update-flash-64-and-reboot</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,update-flash-64-and-reboot + + + + + + Number Inputs + + + + 1 + + + + + + Number Outputs + + + + 1 + + + + + + Block_list + + + + A real pointer to a block list of 64 bit entries + + + + + Out + + + + Status + + + + -1: Hardware error + -3: Image unacceptable to update program + -4: Programming failed when partially complete, and the + flash is now corrupted - reboot may fail + -9002: Not authorized + + + + + The + Status of 0 is never returned, because this + RTAS call does not return if successful. + + + + + The -1 return is to cover the case where some condition + prevents RTAS from being able to program the flash at this + time. For example, the flash programming power supply is + disconnected, a low-level security check (for instance a switch + or jumper) fails, or a test programming probe fails for an + unknown reason or the case where the flash has been + successfully updated, but the reboot fails for some + reason. + + + + + The -3 return is to cover the case where embedded + vendor/platform specific information in the image failed to + conform to the required format or content for this platform, + such as the firmware revision number or a CRC or some other + check which was intended to ensure the integrity of the + image. + + + + + The -4 return is to cover the case where the update + failed before the image was fully updated. In this case, the OS + has the responsibility for reporting the failure. + + + + + The -9002 return code is used to indicate that the + partition at the time the call was made was not authorized to + update the flash image. + + + + +
+ + + + + R1--2. + + The RTAS + ibm,update-flash-64-and-reboot call + Block_list on platforms that do not present the + “ibm,flash-block-version” property in the + OF + /rtas node must conform to the definition shown in + . + + + Format of Block List + + + + + + Length of + Block_list in bytes + + + + + + + Address of memory area 1 + + + + + Length of memory area 1 + + + + + . . . + + + + + Address of memory area n + + + + + Length of memory area n + + + + +
+ + + + + R1--3. + + The + ibm,update-flash-64-and-reboot RTAS call + Block_list must be a sequence of 64 bit cells. + + + + + R1--4. + + Memory blocks referenced in the + ibm,update-flash-64-and-reboot RTAS call + Block_list must reside in System Memory outside that + reserved for firmware (both the RTAS data area and OF’s memory + defined by real-base and real-size). + + + + + R1--5. + + The block list referenced by the + Block_list argument to the + ibm,update-flash-64-and-reboot RTAS call must be in + System Memory below the maximum address supported by the RTAS + instantiated cell size. + + + + + R1--6. + + The addresses of memory blocks referenced + by the + ibm,update-flash-64-and-reboot RTAS call + Block_list must align tn a 4 KB boundary. + + + + + R1--7. + + A memory block, included in the + ibm,update-flash-64-and-reboot RTAS call + Block_list, must not cross a 256MB boundary. + + + + + R1--8. + + The ibm,update-flash-64-and-reboot call must test the + image to make sure it has the right format and is not damaged, update the + flash from the + Block_list and then perform a system reset and + reboot, as for the + system-reboot call. + + + + + + Hardware and Software Implementation Note: Platform + specific information should be embedded in the flash images to identify + the firmware unambiguously and to ensure that the firmware operates + correctly on the platform. Such information might include platform board + model and revision numbers covered by the firmware, manufacturer ID, and + firmware revision number used for external display. This information + should include a CRC or other check which ensures the integrity of the + data. + + Software Implementation Notes: + + + + + The execution time for this calls may be in the order of + seconds, rather than “a few tens of microseconds” as noted on + page + . + + + + The RTAS flash update programs should display progress, + completion, and error information while the flash update is underway, if + possible. + + + + The OS does not expect a return from the + ibm,update-flash-64-and-reboot call other than for + cases where the hardware cannot be accessed, the flash image is + unacceptable to the RTAS flash update program, the result of the update + corrupted the flash, or the platform could not be rebooted. + + + +
+ +
+ Flash Update with Discontiguous Block Lists + The property + “ibm,flash-block-version” (see + ) is defined to describe the + following definition and operation of the + Block_list shown in + . + + + Format of Discontiguous + <emphasis>Block_list</emphasis> + + + + + + + VER + + + Length of + Block_list in bytes + + + + + + + Address of + Block_list extension + + + + + Address of memory area 1 + + + + + Length of memory area 1 + + + + + Address of memory area 2 + + + + + Length of memory area 2 + + + + + - - - + + + + + Address of memory area n + + + + + Length of memory area n + + + + +
+ Where: + + + + VER (1 byte in length) indicates the version of the + Block_list. + + + + Length of the + Block_list in bytes indicates the size of this + Block_list, including the header cell and the cell + with the address of the + Block_list extension. + + + + Address of the + Block_list extension indicates the location of the + next + Block_list. 0x00 indicates no additional + Block_list extension. + + + + Address of memory area 1 (2 . . . n) indicates the location of + this portion of the flash image. + + + + Length of memory area 1 (2 . . . n) indicates the length of this + portion of the flash image. + + + + + + + R1--1. + + If VER is 0x01, the + Block_list must be formatted as in + . + + + + + R1--2. + + If VER is 0x01, the + Block_list parameter in the function call or the + Address of the + Block_list extension, if not 0x00, must point to a + Block_list cell containing VER and Length of the + Block_list. + + + + + R1--3. + + If VER is 0x01, the Address of the + Block_list extension parameter must be 0x00 to + indicate that there are no further extensions. + + + + + R1--4. + + The VER byte must exist in the + Block_list and in each + Block_list extension. + + + + + R1--5. + + If the platform supports the property + “ibm,flash-block-version” with value + 0x01, it must also support the default value 0x00. + + + + + The + Block_list format allows flexibility in the size and + page requirements for the block lists. Page alignment is not required for + the lists or extensions. They may run across contiguous pages with the + control being the length of each list or extension and with the end being + the 0x00 pointer. +
+ +
+ <emphasis>ibm,manage-flash-image</emphasis> + + The + ibm,manage-flash-image RTAS call supports systems + having a “temporary” and “permanent” flash image + areas. It allows the user to commit the temporary flash image by copying + it to the permanent image area. It also allows the user to reject the + temporary flash image by overwriting it with the permanent flash + image. + + + + R1--1. + + The RTAS + ibm,manage-flash-image call must be implemented using + the argument call buffer defined by + . + + + Argument Call Buffer + <emphasis>ibm,manage-flash-image</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for ibm,manage-flash-image + + + + + + Number of Inputs + + + + 1 + + + + + + Number of Outputs + + + + 1 + + + + + + Image to Commit + + + + 0: Reject “temporary” firmware image + 1: Commit “temporary” firmware image + + + + + + + + + + Out + + + + Status + + + + 0: Success + -1: Hardware Error + -2: Busy + -3: Parameter Error + -9001: Cannot Overwrite the Active Firmware Image + Error + -9002 Not Authorized + 990x: Extended Delay + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +
+ + + + + R1--2. + + The ibm,manage-flash-image RTAS call must not change the + system flash and must return a + Status of value -9001 when called with a request to + reject the temporary firmware image when not running on the permanent + firmware image. + + + + + R1--3. + + The ibm,manage-flash-image RTAS call must not change the + system flash and must return a + Status of value -9001 when called with a request to + commit the temporary firmware image when not running on the temporary + firmware image. + + + + + + Platform Implementation Note: In platforms supporting + two firmware image areas, platforms always apply updates to the temporary + image area. The RTAS call + ibm,manage-flash-image is the normal means by which a + temporary image is committed to the permanent side. However, if a + platform is running from a temporary image when an update is to be + applied, then the platform may automatically commit the current temporary + image to the permanent side to allow the new image to be updated to the + temporary image area. The + ibm,validate-flash-image RTAS call is used to + determine what would result from an attempt to update a FLASH image + taking in to account the image to be updated and the current image being + executed. +
+ +
+ <emphasis>ibm,validate-flash-image</emphasis> + + The + ibm,validate-flash-image RTAS call allows OS service + code to determine if a candidate flash image is valid, if the partition + has authority to update the flash image, and what the resulting flash + levels will be after performing the update. + + + + R1--1. + + The ibm,validate-flash-image RTAS call must be + implemented using the argument call buffer described in + . + + + Argument Call Buffer + <emphasis>ibm,validate-flash-image</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,validate-flash-image + + + + + + Number of Inputs + + + + 2 + + + + + + Number of Outputs + + + + 2 + + + + + + Buffer Ptr + + + + Real address of minimum 4 K buffer, contiguous in real + memory + + + + + + Buffer Size + + + + Size in bytes of Buffer + + + + + Out + + + + Status + + + + 990x: Extended Delay + 0: Success + -1: Hardware Error + -2: Busy + -3: Parameter Error + -9002: Not authorized + + + + + + + + + + + + + + + + + + + + + + + + + + Update Results Token + + + + Token to identify what will happen if update is attempted + with this token, described in Requirement + . + + + + +
+ + + + + R1--2. + + The + ibm,validate-flash-image RTAS call + Buffer Ptr parameter must be a real address + representing the starting address of a minimum 4 K buffer, contiguous in + real memory. + + + + + R1--3. + + On input, the + ibm,validate-flash-image RTAS call buffer pointed to + by the + Buffer Ptr parameter must contain the first 4 KB of + the candidate flash image to be validated. + + + + + R1--4. + + For the LPAR option: The + ibm,validate-flash-image RTAS call buffer described + in Requirement + must be in the partition's + RMA. + + + + + R1--5. + + On exit from the + ibm,validate-flash-image RTAS call, RTAS must place + the following data in the buffer, starting at the address in the + Buffer Ptr parameter: + + + + “MI” <sp> current-T-image <sp> + current-P-image <0x0A> + + + + “MI” <sp> new-T-image <sp> new-P-image + <0x00> + + + + “ML” <sp> current-T-image + <sp> current-P-image <0x0A> + + + + “ML” <sp> new-T-image <sp> + new-P-image <0x00> + + + + In Requirement + , current-T-image and + current-P-image are the fixpack microcode image names currently on the + Temporary and Permanent sides, respectively, and new-T-image and + new-P-image are the fixpack microcode image names that will exist in + flash after a successful flash update with the candidate image. + If the current flash image level is not known, the value provided + for current-T-image and/or current-P-image is + “UNKNOWN”. + If the flash update function would not succeed, the values of + new-T-image and new-P-image are the same as current-T-image and + current-P-image, respectively. + + + + + R1--6. + + On exit from the + ibm,validate-flash-image RTAS call, the + Update Results Token output must be updated with one + of the values in + . This list is in order; + firmware must provide the first value in the list which would be true if + an update is attempted: + + + Update Results Token Values + + + + + + + + Token + + + + + Description + + + + + + + + 1 + + + No update done, partition does not have authority to + perform flash update + + + + + 2 + + + No update done, the candidate image is not valid for this + platform + + + + + 3 + + + Current fixpack level is unknown, the new-T-image and + new-P-image identifies show what will exist in flash after + update with this image + + + + + 4 + + + Current T side will be committed to P side before being + replace with new image, and the new image is downlevel from + current image + + + + + 5 + + + Current T side will be committed to P side before being + replaced with new image + + + + + 6 + + + T side will be updated with a downlevel image + + + + + 0 + + + T side will be updated with a newer or identical + image + + + + +
+ + + + +
+ +
+ <emphasis>ibm,activate-firmware</emphasis> + + The + ibm,activate-firmware allows an OS to activate a new + version of firmware that has been updated in the platform flash memory + after the partition was started. + + + + R1--1. + + The ibm,activate-firmware RTAS call must be implemented + using the argument call buffer described in + . + + + Argument Call Buffer + <emphasis>ibm,activate-firmware</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,activate-firmware + + + + + + Number of Inputs + + + + 0 + + + + + + Number of Outputs + + + + 1 + + + + + Out + + + + Status + + + + 990x: Extended Delay + 0: Success + -1: Hardware Error + -2: Busy, try again later + -3: Parameter Error + -9001: No valid FW available to activate + + + + + + + + + + + + + + + + + + + + + + + + +
+ + + + + + Software implementation Note: The OS should expect + that a number of calls may be required to accomplish firmware activation, + with “Busy, try again later” or “Extended Delay” + return codes from all but the last call. The new version of firmware is + not in use until a “Success” return. The OS may interleave + calls to other RTAS functions between calls to this function. +
+ +
+ +
+ SMP Support + In a Symmetric Multiprocessor (SMP) system, the platform needs the + ability to synchronize the clocks on all the processors. The timebase + registers are synchronized by the platform before CPUs are given to the + OS. + + + + R1--1. + + (Merged into Requirement + ) + + + + + R1--2. + + (Merged into Requirement + ) + + + + +
+ <emphasis>stop-self</emphasis> + + The stop-self primitive causes a processor thread to stop + processing OS or user code, and to enter a state in which it is only + responsive to the + start-cpu RTAS primitive. This is referred to as the + RTAS + stopped state. + + + + R1--1. + + A stop-self RTAS call must place the calling processor + thread in the + RTAS + stopped state. This call must be implemented using + the argument call buffer defined by + . + + + + + R1--2. + + RTAS must insure that a processor thread + in the RTAS + stopped state does not checkstop or otherwise fail if + a machine check or soft reset exception occurs. Processor threads in this + state receive the exception, but must perform a null action and remain in + the RTAS + stopped state. + + + Argument Call Buffer + <emphasis>stop-self</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + stop-self + + + + + + Number Inputs + + + + 0 + + + + + + Number Outputs + + + + 1 + + + + + Out + + + + Status + + + + If successful, this call does not return + -1: Hardware Error + + + + +
+ Software Implementation Note: If this call succeeds, it does not + return. The CPU thread waits for some other processor thread to issue a + start-cpu targeted to this processor thread. + + Firmware Implementation Note: In an LPAR environment + the state of the interrupt sub-system associated with this processor on + entry to this call cannot be trusted. Although interrupts are masked as + part of the RTAS call protocol, the caller may have left the processor + configured as an interrupt server. Therefore, interrupt signals may be + pending within the processor’s interrupt management area. These + conditions need to be cleared prior to allocating this processor to + another partition. + + + + + R1--3. + + Platforms which support the enhanced + stop-self RTAS behavior must include the name only + “ibm,integrated-stop-self” OF property, + under the + /rtas node, and prior to placing a processor in the + stopped state, flush and disable any caches/memory exclusively used by + the issuing processor. + + Architecture Note: In Requirement + , an exclusively used cache + means that no other running processor currently needs the cache for + normal operation, even if the cache could potentially be shared with + other processors. An exclusively used memory means any main memory + allocated local to the processor thread and thus not accessible by other + processor threads. + + + + + R1--4. + + Execution of the + stop-self call by the last active processor thread + must cause the firmware to recover all the resources owned by the + executing OS image for use per platform policy. + + + + +
+ +
+ <emphasis>start-cpu</emphasis> + + The start-cpu primitive is used to cause a processor thread which + is currently in the RTAS + stopped state to start processing at an indicated location. + + + + R1--1. + + A start-cpu RTAS call must remove the processor thread + specified by the + CPU_id parameter from the RTAS + stopped state. This call must be implemented using + the argument call buffer defined by + . + + + + + R1--2. + + The processor thread specified by the + CPU_id parameter must be in the RTAS + stopped state entered because of a prior call by that + processor to the + stop-self primitive. + + + + + R1--3. + + When a processor thread exits the RTAS + stopped state, it must begin execution in real mode, + with the MSR in the same state as from a system reset interrupt (except + for the MSRHV bit which is on if not running under a hypervisor + and off if running under a hypervisor) at the real location indicated by + the + Start_location parameter, with register R3 set to the + value of parameter + Register_R3_contents and the MSR as defined in + . All other register contents + are indeterminate. + + + Argument Call Buffer + <emphasis>start-cpu</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + start-cpu + + + + + + Number Inputs + + + + 3 + + + + + + Number Outputs + + + + 1 + + + + + + Cpu_id + + + + Token identifying the processor thread to be started, + obtained from the value of the + + “ibm,ppc-interrupt-server#s” property for + the CPU in the OF device tree + + + + + + Start_location + + + + Real address at which the designated CPU begins + execution + + + + + + Register_R3_contents + + + + Value which is loaded into Register R3 before beginning + execution at Start_location + + + + + Out + + + + Status + + + + 0: Success + -1: Hardware Error + + + + +
+ + + + + + Note: Requirement + applies to the start-cpu RTAS + call. At the completion of start-cpu, the caches to be used by the + specified processor must have been initialized and the state bits made + accurate prior to beginning execution at the start address. + + + Machine State Register (MSR) State in Started + Processor + + + + + + + + + + + + Bit Number + + + + + Name + + + + + Initial Value upon start by + start-cpu + + + + + Bit Number + + + + + Name + + + + + Initial Value upon start by + start-cpu + + + + + + + + 0 + + + SF + + + 0 if RTAS instantiated in 32 bit mode 1 if RTAS + instantiated in 64 bit mode + + + 53 + + + SE + + + 0 + + + + + 1 + + + Reserved + + + 0 + + + 54 + + + BE + + + 0 + + + + + 2 + + + Reserved + + + 0 + + + 55 + + + FE1 + + + Implementation Dependent + + + + + 3 + + + HV + + + 0 if running under hypervisor firmware, 1 if running in + “SMP” mode + + + 56 + + + US + + + 0 + + + + + 4:46 + + + Reserved + + + 0 + + + 57 + + + Reserved + + + 0 + + + + + 47 + + + ILE + + + 0 + + + 58 + + + IR + + + 0 + + + + + 48 + + + EE + + + 0 + + + 59 + + + DR + + + 0 + + + + + 49 + + + PR + + + 0 + + + 60 + + + Reserved + + + 0 + + + + + 50 + + + FP + + + Implementation Dependent + + + 61 + + + PMM + + + 0 + + + + + 51 + + + ME + + + 1 + + + 62 + + + RI + + + 0 + + + + + 52 + + + FE0 + + + Implementation Dependent + + + 63 + + + LE + + + 0 + + + + +
+
+ +
+ <emphasis>query-cpu-stopped state</emphasis> + + The query-cpu-stopped-state primitive is used to query a different + processor thread to determine its status with respect to the RTAS stopped + state. + + + + R1--1. + + A query-cpu-stopped-state RTAS call must return the + CPU_status of the processor thread specified by the + Cpu_id parameter. This call must be implemented using + the argument call buffer defined by + . + + + Argument Call Buffer + <emphasis>query-cpu-stopped-state</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + query-cpu-stopped-state + + + + + + Number Inputs + + + + 1 + + + + + + Number Outputs + + + + 2 + + + + + + Cpu_id + + + + Token identifying the processor thread to be queried, + obtained from the value of the + + “ibm,ppc-interrupt-server#s” property for + the CPU in the OF device tree + + + + + Out + + + + Status + + + + 0: Success + -1: Hardware Error + -2: Hardware Busy, Try again later + + + + + + CPU_status + + + + 0: The processor thread is in the RTAS stopped + state + 1: + stop-self is in progress + 2: The processor thread is not in the RTAS stopped + state + + + + +
+ + + + + + Firmware Implementation Note: RTAS serialization may + be required between the + stop-self and the + query-cpu-stopped-state calls. + + Software Implementation Note: The OS performs a + stop-self on the desired processor thread, then + periodically call + s query-cpu-stopped-state on another processor thread + until the desired processor thread is stopped. Before calling + set-power-level to power off the desired processor, + or isolate the logical CPU, the platform requires that all processor + threads be in the RTAS stopped state. +
+ +
+ +
+ Miscellaneous RTAS Calls + + +
+ <emphasis>ibm,os-term</emphasis> + + This RTAS call is provided for the OS to indicate to the platform + that it has terminated normal operation. A string of information is + passed to the platform. + A call to the + ibm,os-term RTAS function implies the following to + the platform: + + + + Any platform reporting and recovery policies may now take + effect. + + + + The OS may no longer be issuing periodic + event-scan requests, so surveillance monitoring does + not continue. + + + + All devices not marked + “used-by-rtas” are released by the OS + (including, for example, native serial ports used by a service + processor). + + + + The OS no longer responds to any EPOW events, so it is up to the + platform to take any appropriate actions for such events. + + + + Due to the above implications, the platform may take actions (for + example, a service processor “call home”) that could conflict + with normal processing of further RTAS requests. However, since the OS + has entered a “live halt” state, the list of RTAS functions + that it still needs is relatively small. The list of RTAS functions that + the platform might expect to see after + ibm,os-term includes: + + + + nvram-fetch + + + + nvram-store + + + + display-character + + + + power-off + + + + ibm,power-off-ups + + + + system-reboot + + + + check-exception for machine checks (Although the OS + may still react normally to a machine check condition by calling + check-exception, it might not process a returned + error log. It is allowable for + check-exception to not return an extended log when in + this state.) + + + + If a platform has a service processor, and a policy has been + established for actions to be taken by the service processor upon + receiving notice of OS termination, the service processor may complete + those actions and a return to the CPU from this call may never occur. If + the call does return, the OS performs its own termination policy. + + When the platform supports extended + ibm,os-term behavior, the return to the RTAS will + always occur unless there is a kernel assisted dump active as initiated + by an + ibm,configure-kernel-dump call. + Platforms capable of supporting this extended + ibm,os-term behavior will so indicate by presenting + the + “ibm,extended-os-term” RTAS property in + the OF device tree. + + + + R1--1. + + RTAS must implement an + ibm,os-term call using the argument call buffer + defined by + to receive a termination string + from the OS. + + + Argument Call Buffer + <emphasis>ibm,os-term</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,os-term + + + + + + Number Inputs + + + + 1 + + + + + + Number Outputs + + + + 1 + + + + + + Pointer to String + + + + NULL terminated string + + + + + Out + + + + Status + + + + 0:success + -1:hardware error + -2:hardware busy, try again later + + + + + + + + + + + + + + +
+ + Platform Implementation Note: The string should be + maintained in an error log which could be made accessible to a service + location or saved in the platform for later remote access. + + + + + R1--2. + + The ibm,os-term call must disable surveillance. + + + + + R1--3. + + During the machine check and soft reset + handlers, the platform must support access to the + ibm,os-term RTAS function. + + + + + R1--4. + + If the + ibm,os-term call does not return to the caller, the + platform must honor the partition_auto_restart system parameter + value. + + + + + R1--5. + + For platforms supporting extended + ibm,os-term behavior, the + ibm,os-term call must always return unless there is + an active kernel assisted dump configured as specified by an + ibm,configure-kernel-dump RTAS call. + + + + + + Platform implementation note: The + ibm,os-term RTAS call allows for the case where the + OS and platform may share an I/O device such as a TTY where the OS would + have use of the device normally, and the platform use when the OS has + terminated, such as to implement an error reporting call home function + both in the OS and the platform. For proper sharing in such a case where + extended behavior is supported, when the primary partition console is + also used for the call-home by the platform, the platform should not + initiate the call home until after the partition shuts down. +
+ +
+ <emphasis>Ibm,exti2c</emphasis> + + For support of platforms which require an external + I2C bus, a special port to the service processor is + required. The EXTI2C option is designed to control specific external + devices. Designers cannot assume that an arbitrary + I2C device may be substituted. + The + ibm,exti2c call provides a single channel to the + I2C bus. Through this channel, software can read or + write up to 256 bytes from/to an addressed resource within an address + space between X’000000 and X’FFFFFF. Reference the + specification for the specific I2C device to determine what effect such operations + may have. + The Buffer Pointer argument is used to manage this channel across + multiple + ibm,exti2c RTAS calls. If the input Buffer Pointer + value on a call is zero, the state of the channel is reset and any + outstanding I2C operation is aborted. If the input Buffer Pointer + has a different value from that of the last call, a new operation is + started, with any previous operation being aborted. An input Buffer + Pointer value that is the same as that used on the previous call + indicates a continuation of the last operation, given that the + Status of the last call was not 0 (success) or -1 + (hardware error). These terminating statuses reset the channel. + Using software must manage serialization to the + ibm,exti2c channel across multiple calls for the same + I2C operation. + A single + ibm,exti2c operation may require an extended period + of processing by background hardware. During this time, RTAS returns + either a + Status code of -2 or 990x. A + Status of -2 indicates that RTAS may be capable of + doing useful processing immediately. + A + Status code of 990x indicates that the platform + requires an extended period of time to perform the operation. It is + suggested that software delay for 10 raised to the x milliseconds before + calling + ibm,exti2c with the same Buffer Pointer value, + however, software may call again earlier or later. + A + Status code of -1 indicates either a general error + associated with the local + I2C hardware (service processor) or that the channel + has been corrupted due to other error conditions not associated with the + I2C operation. If the buffer is changed, as when an + error code is returned, the RTAS + Status code is 0 (success). + + + + R1--1. + + For the EXTI2C option: RTAS must implement an + ibm,exti2c call using the argument call buffer + defined by + to allow communications with + special hardware. + + + ibm,exti2c Argument Call Buffer + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,exti2c + + + + + + Number Inputs + + + + 1 + + + + + + Number Outputs + + + + 1 + + + + + + Buffer Pointer + + + + Real Address of data buffer + + + + + Out + + + + Status + + + + 0:Success + -1:hardware error + -2:hardware busy, try again later + -3: Parameter error + 990x:Extended delay where x is a number 0-5 + + + + + + + + + + + + + + + + + + + +
+ + + + + R1--2. + + For the EXTI2C option: The Buffer Pointer must point + to a contiguous real storage area large enough to contain the + I2C command and any associated data (maximum of 261 + bytes). + + + + + R1--3. + + For the EXTI2C option: The Buffer format for the + write operation must be as defined in + . + + + EXTI2C Buffer Write Operation Format + + + + + + + + + Condition + + + + + Byte # + + + + + Content + + + + + + + + On Call + + + 0 + + + 0x00 + + + + + 1-3 + + + Address of I2C resource + + + + + 4 + + + Length of op. (1-255 with 0 specifying 256) + + + + + 5... + + + Data + + + + + On Return - I2C OK + + + 0 + + + Buffer unmodified + + + + + 1-3 + + + + + 4 + + + + + 5... + + + + + On Return - I2C error + + + 0 + + + 0x01 + + + + + 1-3 + + + Address of I2C resource + + + + + 4 + + + I2C operation error code + + + + +
+ + Firmware and Software Implementation Note: When the + ibm,exti2c RTAS call write operation returns after + the operation has been enqueued by the firmware but prior to completion + by the hardware (therefore the operation status is truly not known), the + ibm,exti2c RTAS call can return a + Status of 0 (success) with the buffer + unmodified. + + + + + R1--4. + + For the EXTI2C option: The Buffer format for a read + operation, if supported, must be as defined in + . + + + EXTI2C Buffer Read Operation Format (Optional) + + + + + + + + + Condition + + + + + Byte # + + + + + Content + + + + + + + + On Call + + + 0 + + + 0x80 + + + + + 1-3 + + + Address of I2C resource + + + + + 4 + + + Length of op. (1-255 with 0 specifying 256) + + + + + 5... + + + Data + + + + + On Return - I2C OK + + + 0 + + + 0x80 + + + + + 1-3 + + + Address of I2C resource + + + + + 4 + + + Length of op. (1-255 with 0 specifying 256) + + + + + 5... + + + Data + + + + + On Return - I2C error + + + 0 + + + 0x81 + + + + + 1-3 + + + Address of I2C resource + + + + + 4 + + + I2C operation error code + + + + +
+ + + + + R1--5. + + For the EXTI2C option: If read operations are not + supported and a read operation is attempted, then the platform must + return a + Status of -3. + + + + + R1--6. + + For the EXTI2C option: The maximum total Extended + Delay imposed by the + ibm,exti2c command for a single + I2C operation must be less than 2 seconds. + + + + + R1--7. + + For the EXTI2C option: When the + ibm,exti2c RTAS call returns an EXTI2C buffer + containing an I2C operation error code, the RTAS + Status code must be 0 (success). + + + + + + Firmware and Software Implementation Note: When the + ibm,exti2c RTAS call returns after the operation has + been enqueued by the firmware but prior to completion by the hardware + (therefore the operation status is truly not known), the + ibm,exti2c RTAS call can return a + Status of 0 (success) with the buffer + unmodified. +
+ +
+ +
+ PowerPC External Interrupt Option + The RTAS calls used to access the facilities of the PowerPC + External Interrupt option need not be serialized by the calling OS. Other + RTAS rules such as being called in real mode with interrupts disabled + still apply. + + Note: These RTAS calls make the PowerPC External + Interrupt option Logical Partition (LPAR) ready. + +
+ <emphasis>ibm,get-xive</emphasis> + + + + R1--1. + + For the PowerPC External Interrupt option: RTAS must + implement an + ibm,get-xive call using the argument call buffer + defined by + . + + + + + R1--2. + + For the PowerPC External Interrupt option: The + ibm,get-xive call must be reentrant to the number of + processors on the platform. + + + + + R1--3. + + For the PowerPC External Interrupt option: The + ibm,get-xive argument call buffer for each + simultaneous call must be physically unique. + + + + + R1--4. + + For the PowerPC External Interrupt option: The + ibm,get-xive call must return the current values of + the server number and priority fields, as set by the last + ibm,set-xive call (priority initialized to least + favored level by firmware at boot), of the External Interrupt Vector + Entry associated with the interrupt number provided as an input argument + unless prevented by Requirement + . + + + + + R1--5. + + For the PowerPC External Interrupt option: The + ibm,get-xive call must return the + Status of -3 (Argument Error) for an unimplemented + Interrupt # (not reported via an + “interrupt-ranges” property). + + + + + R1--6. + + For the PowerPC External Interrupt option combined with the + Platform Reserved Interrupt Priority Level option: The + ibm,get-xive call must return the + Status of -3 (Argument Error) for an platform + reserved interrupt priority (reported via an the + + “ibm,plat-res-int-priorities” property). + + + Argument Call Buffer + <emphasis>ibm,get-xive</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,get-xive + + + + + + Number Inputs + + + + 1 + + + + + + Number Outputs + + + + 3 + + + + + Interrupt # + + + From + + “interrupt-ranges” property + + + + + Out + + + + Status + + + + 0: Success + -1: Hardware Error + -3: Argument Error (Optional) + + + + + + Server # + + + + 0x0 - 2 + “ibm,interrupt-server#-size” + + + + + + + Priority + + + + 0x0 - 0xff + + + + +
+ + + + +
+ +
+ <emphasis>ibm,set-xive</emphasis> + + + + R1--1. + + For the PowerPC External Interrupt option: RTAS must + implement an + ibm,set-xive call using the argument call buffer + defined by + . + + + + + R1--2. + + For the PowerPC External Interrupt option: The + ibm,set-xive call must be reentrant to the number of + processors on the platform. + + + + + R1--3. + + For the PowerPC External Interrupt option: The + ibm,set-xive argument call buffer for each + simultaneous call must be physically unique. + + + + + R1--4. + + For the PowerPC External Interrupt option: The + ibm,set-xive call must set values of the server + number and priority fields of the External Interrupt Vector Entry (XIVE) + and/or firmware saved priority value (if the interrupt source controller + does not use an interrupt Enable Register and the interrupt source is + masked off, either due to a previous + ibm,int-off call or because the interrupt source was + never enabled with an + ibm,int-on call since boot), associated with the + interrupt number provided as an input argument unless prevented by + Requirement + . + + + + + R1--5. + + For the PowerPC External Interrupt option: The + ibm,set-xive call must return the + Status of -3 (Argument Error) for an unimplemented + Interrupt number. + + + + + R1--6. + + + For the PowerPC External Interrupt plus the Platform Reserved + Interrupt Priority Level option: The + ibm,set-xive call must return the + Status of -3 (Argument Error) for an reserved + Priority value (as reported via an + + “ibm,plat-res-int-priorities” property). + + + Argument Call Buffer + <emphasis>ibm,set-xive</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,set-xive + + + + + + Number Inputs + + + + 3 + + + + + + Number Outputs + + + + 1 + + + + + + Interrupt # + + + + Interrupt number from appropriate OF device tree + property + + + + + + Server # + + + + 0x00 - 2 + + “ibm,interrupt-server#-size” + + + + + + Priority + + + + 0x00 - 0xFF + + + + + Out + + + + Status + + + + 0: Success + -1: Hardware Error + -3 Argument Error (Optional) + + + + +
+ + + + +
+ +
+ <emphasis>ibm,int-off</emphasis> + + + + R1--1. + + For the PowerPC External Interrupt option: RTAS must + implement an + ibm,int-off call using the argument call buffer + defined by + . + + + + + R1--2. + + For the PowerPC External Interrupt option: The + ibm,int-off call must be reentrant to the number of + processors on the platform. + + + + + R1--3. + + For the PowerPC External Interrupt option: The + ibm,int-off argument call buffer for each + simultaneous call must be physically unique. + + + + + R1--4. + + For the PowerPC External Interrupt option: The + ibm,int-off call must disable interrupts from the + interrupt source associated with the interrupt number provided as an + input argument unless prevented by Requirement + . + + + + + R1--5. + + For the PowerPC External Interrupt option: If the + interrupt source controller uses an Interrupt Enable Register, the + ibm,int-off call must reset the mask bit associated + with the specified interrupt number; or if the interrupt source + controller does not use an interrupt Enable Register, the + ibm,int-off call must save the priority value of the + XIVE for later restoration by the + ibm,int-on call, or presentation by the + ibm,get-xive call and set the priority value of the + XIVE to the least favored priority value (0xFF), unless prevented by + Requirement + . + + + + + R1--6. + + For the PowerPC External Interrupt option: The + ibm,int-off call must return the + Status of -3 (Argument Error) for an unimplemented + Interrupt number. + + + Argument Call Buffer + <emphasis>ibm,int-off</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,int-off + + + + + + Number Inputs + + + + 1 + + + + + + Number Outputs + + + + 1 + + + + + + Interrupt # + + + + Interrupt number from appropriate OF device tree + property + + + + + Out + + + + Status + + + + 0: Success + -1: Hardware Error + -3 Argument Error (Optional) + + + + +
+ + + + +
+ +
+ <emphasis>ibm,int-on</emphasis> + + + + R1--1. + + For the PowerPC External Interrupt option: RTAS must + implement an + ibm,int-on call using the argument call buffer + defined by + . + + + + + R1--2. + + For the PowerPC External Interrupt option: The + ibm,int-on call must be reentrant to the number of + processors on the platform. + + + + + R1--3. + + For the PowerPC External Interrupt option: The + ibm,int-on argument call buffer for each simultaneous + call must be physically unique. + + + + + R1--4. + + For the PowerPC External Interrupt option: The + ibm,int-on call must enable interrupts from the + interrupt source associated with the interrupt number provided as an + input argument unless prevented by Requirement + . + + + + + R1--5. + + For the PowerPC External Interrupt option: If the + interrupt source controller uses an Interrupt Enable Register, the + ibm,int-on call must set the mask bit associated with + the specified interrupt number; or if the interrupt source controller + does not use an interrupt Enable Register, the + ibm,int-on call must restore the XIVE priority value + saved by the previous + ibm,int-off call (initialized by the firmware to the + least favored level at boot) unless prevented by Requirement + . + + + + + R1--6. + + For the PowerPC External Interrupt option: The + ibm,int-on call must return the + Status of -3 (Argument Error) for an unimplemented + Interrupt number. + + + Argument Call Buffer + <emphasis>ibm,int-on</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,int-on + + + + + + Number Inputs + + + + 1 + + + + + + Number Outputs + + + + 1 + + + + + + Interrupt # + + + + Interrupt number from appropriate OF device tree + property + + + + + Out + + + + Status + + + + 0: Success + -1: Hardware Error + -3 Argument Error (Optional) + + + + +
+ + + + +
+ +
+ MSI Support + This section describes the RTAS calls required when the MSI option + is implemented. See + for other platform requirements + for the MSI option. + The Message Signaled Interrupt (MSI) and Enhanced MSI (MSI-X) + capability of PCI IOAs in many cases allows for greater flexibility in + assignment of external interrupts to IOAs than the predecessor Level + Sensitive Interrupt (LSI) capability, and in some cases allows the + treatment of MSIs + + This architecture will refer generically to the MSI and MSI-X + capabilities as simply “MSI,” except where differentiation + is required. + as a resource pool that is reassigned based on availability of + MSIs and the need of an IOA function for more interrupts than initially + assigned. Platforms that implement the MSI option implement the + ibm,change-msi and + ibm,query-interrupt-source-number RTAS calls. + +
+ <emphasis>ibm,change-msi</emphasis> + The OS uses the + ibm,change-msi RTAS call to query the initial number + of MSIs assigned to a PCI configuration address (that is, to an IOA + function) and to request a change in the number of MSIs assigned, when + the platform allows for dynamic reassignment of MSIs for the IOA + function. The + ibm,change-msi RTAS call allows the caller to allow + the platform to select MSI or MSI-X, to specifically select MSI or MSI-X + or, if LSIs are allocated by the firmware for the IOA function, to change + to LSI (by removal of the MSIs assigned). The interrupt source numbers + assigned to an IOA function are queried via the + ibm,query-interrupt-source-number RTAS call. The + ibm,query-interrupt-source-number RTAS call is called + iteratively, once for each interrupt assigned to the IOA function. The + interrupt source numbers returned by the + ibm,query-interrupt-source-number RTAS call are the + numbers used to control the interrupt as in the + ibm,get-xive, + ibm,set-xive, + ibm,int-on, and + ibm,int-off RTAS calls. + If a device driver is willing to live with the platform-assigned + initial number of MSIs, then the device driver does not need to use the + ibm,change-msi RTAS call, and can instead use the + ibm,query-interrupt-source-number RTAS call to + determine the number of interrupts assigned to each IOA function. + An OS may abandon the effort to change the MSIs for a given + configuration address after the first call to + ibm,change-msi and prior to a call which gets a + status back indicating completion, by calling again with the same PCI + configuration address but with a + Function number of 2 (set to default number of + interrupts) and a + Sequence Number of 1. RTAS never returns a + Status of -2 or 990x when the call is made with a + Function number of 2. + If an OS successfully changes the number of interrupts, then it + should consider removing the increase when it deconfigures the IOA + function, especially if it starts with zero and wants to be backward + compatible with older device drivers that may not understand MSIs. To + remove all MSIs, set the Requested Number of Interrupts to zero. But it + should be noted, that once set to zero, there is no guarantee that on a + future request there will be any MSIs available to assign from the pool. + Adding MSIs to an IOA function which has LSIs assigned disables those + LSIs but does not remove them, and then removing the MSIs that replaced + the LSIs re-uses the same (previously removed) LSIs (mapped to the same + LSI source numbers as the previous LSI source numbers). + The presence of the + “ibm,change-msix-capable” property + specifies that the platform implements the version of this RTAS call that + allows + Number Outputs equal to 4 and + Functions 3 and 4. + If the + ibm,change-msi RTAS call is made with + Number Outputs equal to 4 or with + Function equal to 3 or 4 when the + “ibm,change-msix-capable” property does + not exist in the + /rtas node, then the call will return a + Status of -3 (Invalid Parameter). Specifying + Function 3 (MSI) also disables MSI-X for the + specified IOA function, and likewise specifying + Function 4 (MSI-X) disables MSI for the IOA function. + It is unnecessary to specify a + Requested Number of Interrupts of zero when switching + between MSI and MSI-X. Specifying the + Requested Number of Interrupts to zero for either + Function 3 or 4 removes all MSI & MSI-X + interrupts from the IOA function. It is permissible to use LSI, MSI and + MSI-X on different IOA functions. + The default (initial) assignment of interrupts is defined in + . + + + + R1--1. + + For the MSI option: The platform must implement the + ibm,change-msi call using the argument call buffer + defined by + . + + + Argument Call Buffer + <emphasis>ibm,change-msi</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,change-msi. + + + + + + Number Inputs + + + + 6 + + + + + + Number Outputs + + + + 3 or 4, when the + + “ibm,change-msix-capable” property is + present, 3 otherwise. + + + + + + Config_addr + + + + Configuration Space Address (Register field set to + 0) + + + + + + PHB_Unit_ID_Hi + + + + Represents the most-significant 32-bits of the Unit ID of + the PHB that corresponds to the + config_addr + + + + + + PHB_Unit_ID_Low + + + + Represents the least-significant 32-bits of the Unit ID + of the PHB that corresponds to the + config_addr + + + + + + Function + + + + Determines action of this call: + 0: Query only (only return actual number of MSI or MSI-X + interrupts assigned to the PCI configuration address). + 1: If + Number Outputs is equal to 3, request to + set to a new number of MSIs (including set to 0). + If the + + “ibm,change-msix-capable” property exists + and + Number Outputs is equal to 4, request is to + set to a new number of MSI or MSI-X (platform choice) + interrupts (including set to 0). + 2: Request to set back to the default number of + interrupts (also aborts a change in progress; that is, one that + has previously returned a + Status of -2 or 990x) + 3: (Only valid if + + “ibm,change-msix-capable” exists): + Request to set to a new number of MSIs (including set to + 0) + 4: (Only valid if + + “ibm,change-msix-capable” exists): + Request to set to a new number of MSI-X interrupts (including + set to 0) + + + + + + Requested Number of Interrupts + + + + The total number of MSIs being requested for the PCI + configuration address. A value of 0 is specified in order to + remove all MSIs for the PCI configuration address. This input + parameter is ignored by RTAS for + Function values other than 1, 3, or + 4. + + + + + + Sequence Number + + + + Integer representing the sequence number of the call. + First call in sequence starts with 1, following calls (if + necessary) use the + Next Sequence Number returned from the + previous call. + + + + + Out + + + + Status + + + + -3: Parameter error + -2: Call again + -1: Hardware error + 0: Success + 990x: Extended Delay + + + + + + Final Number of Interrupts + + + + Number of interrupts assigned to the PCI configuration + address at the successful completion of this call ( + Status of 0). For + Function 1, 3, or 4, if a greater number + was requested than what was previously assigned, the final + number may be less than what was requested, even though a + Status of 0 is returned. + + + + + + Next Sequence Number + + + + Integer to be returned as the + Sequence Number parameter on the next call. + This output is only valid if a + Status of -2 or 990x is returned. + + + + + + Type of Interrupts + + + + This field is only valid when the + Final Number of Interrupts is + non-zero. + 1: MSI + 2: MSI-X + + + + +
+ + + + + R1--2. + + For the MSI option: The + Final number of Interrupts and + Type of Interrupts must be valid when the platform + returns a + Status of 0 (Success), regardless of whether the + original number and final number of interrupts assigned is different and + regardless of whether or not the platform allows MSI resources to be + reassigned for the specified PCI configuration address. + + + + + R1--3. + + For the MSI option: The platform must return a + Status of -3 (Parameter error) from + ibm,change-msi, with no change in interrupt + assignments if the PCI configuration address does not support MSI and + Function 3 was requested (that is, the + “ibm,req#msi” property must exist for the + PCI configuration address in order to use + Function 3), or does not support MSI-X and + Function 4 is requested (that is, the + “ibm,req#msi-x” property must exist for + the PCI configuration address in order to use + Function 4), or if neither MSIs nor MSI-Xs are + supported and + Function 1 is requested. + + + + + R1--4. + + For the MSI option: If there are zero MSIs assigned + to the target IOA function but there is one or more LSIs assigned, then a + call to + ibm,change-msi which successfully changes the number + of MSIs assigned to non-zero must also disable the LSIs in the IOA + function’s configuration space and must keep the LSI platform + resources available to the IOA function in the case the MSIs are removed + (see Requirement + ). + + + + + R1--5. + + For the MSI option: + If there are a + non-zero number of MSIs assigned to the target IOA function and if that + IOA function originally had some LSIs assigned, then a call to + ibm,change-msi which successfully changes the number + of MSIs assigned to zero must also reassign any LSIs that were originally + assigned to that IOA function, using the same interrupt number that was + originally assigned (that is, the platform must reserve an originally + assigned LSI for a IOA function in case it needs to reassign it), and + must enable the LSIs in the IOA function’s configuration + space. + + + + + R1--6. + + For the MSI option: If the platform supports the + changing of MSIs, then it must support the reduction in the number of + interrupts by the + ibm,change-msi call, including setting the number of + MSIs to 0. + + + + + R1--7. + + For the MSI option: On the first call of + ibm,change-msi, the + Sequence Number must be a 1. + + + + + R1--8. + + For the MSI option: If + ibm,change-msi returns a + Status of -2 (Call again) or 990x (Extended Delay), + then the caller must provide on the next call to + ibm,change-msi, one of the following: + + + + All input parameters the same as the initial call except with the + Sequence Number set to the value in + Next Sequence Number returned from the previous + ibm,change-msi call. + + + + All input parameters the same as the initial call except with + Function set to 2 and the + Sequence Number set to 1, if the caller is wanting to + abort the previously started + ibm,change-msi operation. + + + + + + + R1--9. + + For the MSI option: If the + ibm,change-msi RTAS call returns something other than + 0 for the + Final Number of Interrupts, then the + ibm,query-interrupt-source-number RTAS call must be + used to get the current interrupt source numbers, even if the + ibm,change-msi call has returned the same number of + interrupts as before the call. + + + + + R1--10. + + For the MSI option: Firmware must not return a + Status of -2 or 990x when the + Requested Number of Interrupts is set to 0 or for + Function 0 (query only) or for + Function 2 (set back to default number). + + + + + R1--11. + + For the MSI option: When the + set-indicator RTAS call is made to isolate an IOA + (for both DLPAR and PCI Hot Plug operations), the platform must release + any additional MSI numbers that were obtained through the + ibm,change-msi RTAS call and make them available for + use by other + ibm,change-msi calls. + + + + + R1--12. + + For the MSI option: An OS or device driver that is + calling + ibm,change-msi for the purpose of changing the number + or type of interrupts for the IOA function must assure that the IOA + function cannot be actively performing operations that will generate + interrupts during the process of changing the number or type of + interrupts. + + + + + R1--13. + + For the MSI option: The platform must restore the + IOA’s MSI configuration space after a reset operation which occurs + following boot, to what it was previous to the reset operation, and + provide the same MSI assignments through the reset operation, unless a DR + isolate/unisolate operation has been performed (in which case the IOA's + MSI configuration space is set as it would at boot time). + + + + + + Software Implementation Notes: + + + + + Interrupt source numbers for MSIs are not necessarily be + assigned contiguously. + + + + MSIs and MSI source numbers are not shared (see Requirement + ). + + + + For a multi-function IOA, the + ibm,change-msi call is called for each function for + which the number of MSIs is to be changed. + + + + When the 990x + Status is returned, it is suggested that software + delay for 10 raised to the x milliseconds (where x is the last digit of + the 990x return code), before calling + ibm,change-msi again. However, software may issue the + + ibm,change-msi call again either earlier or later + than this. + + + + During a sequence of calls which return -2 or 990x, software may + abort at any time by setting the + Function equal to 2 and the + Sequence Number to 1. + + + + When there is a non-zero number of MSI or MSI-X interrupts + assigned, and when software attempts to change the type of interrupts + (MSI to MSI-X interrupt or MSI-X to MSI) at the same time as changing the + number of interrupts, the platform may return the same number of + interrupts as previously assigned, even though a greater number is + available. In this case a second call to + ibm,change-msi to increase the number of interrupts + may produce a greater number of interrupts. + + + +
+ +
+ <emphasis>ibm,query-interrupt-source-number</emphasis> + The + ibm,query-interrupt-source-number RTAS call is used + to query the interrupt source number and type (level sensitive for LSIs, + edge triggered for MSIs) for a specific PCI IOA function’s + interrupt, if one exists. That is, for a given PCI configuration address + ( + PHB_Unit_ID_Hi, PHB_Unit_ID_Low, and + config_addr) and function interrupt number. This + call is issued once for each interrupt of each IOA function, in order to + obtain the interrupt source number and type for that interrupt. For + example, if the + ibm,change-msi RTAS call has previously returned a + value of “n” interrupts for the IOA function, then the call + is made “n” times for that function (with a relative + interrupt number of 0 to n-1). + + + + R1--1. + + For the MSI option: The platform must implement the + ibm,query-interrupt-source-number RTAS call using the + argument call buffer defined by + + . + +   + + Argument Call Buffer + <emphasis>ibm,query-interrupt-source-number</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,query-interrupt-source-number + + + + + + Number Inputs + + + + 4 + + + + + + Number Outputs + + + + 3 + + + + + + Config_addr + + + + Configuration Space Address (Register field set to + 0) + + + + + + PHB_Unit_ID_Hi + + + + Represents the most-significant 32-bits of the Unit ID of + the PHB that corresponds to the + config_addr + + + + + + PHB_Unit_ID_Low + + + + Represents the least-significant 32-bits of the Unit ID + of the PHB that corresponds to the + config_addr + + + + + + IOA Function Interrupt Number + + + + The relative number of the interrupt within the PCI + configuration address, with a value of 0 being the first + interrupt of the PCI configuration address. + + + + + Out + + + + Status + + + + -3: Parameter error + -1: Hardware error + 0: Success + 1: No interrupt assigned for the given PCI configuration + address and + IOA Function Interrupt Number. + + + + + + Interrupt Source Number + + + + The interrupt source number corresponding to the PCI + configuration address and + IOA Function Interrupt Number, when a + Status of 0 is returned. Undefined for + other + Status values + . + + + + + + Interrupt Source Trigger + + + + The interrupt source trigger corresponding to the PCI + configuration address and + IOA Function Interrupt Number, when a + Status of 0 is returned. Undefined for + other + Status values + . + 0: Level sensitive + 1: Edge triggered + + + + +
+ + + + + R1--2. + + For the MSI option: The interrupt source numbers + returned by the + ibm,query-interrupt-source-number RTAS call must be + the numbers used to control the interrupt as in the + ibm,get-xive, + ibm,set-xive, + ibm,int-on, and + ibm,int-off RTAS calls. + + + + + R1--2. + + For the MSI option: The + ibm,query-interrupt-source-number RTAS call must + return a + Status of 1 (no interrupt assigned) if the inputs + specify a valid PCI configuration address and the PCI configuration + address does not have an interrupt assigned for the specified + IOA Function Interrupt Number. + + + + + + Software and Firmware Implementation Note: Software + may use the + ibm,query-interrupt-source-number RTAS call for all + IOA Function Interrupt Number values starting at 0 + until a + Status of 1 is returned, rather than using + ibm,change-msi Function 0 (query). That is, the + ibm,query-interrupt-source-number RTAS call works + even when the + “ibm,req#msi” property does not exist for + the IOA (that is even when the IOA is not requesting one or more MSIs), + This might be desirable, for example, if software never plans on using + the capability to change the number of MSIs, and therefore does not have + any other use for the + ibm,change-msi call. +
+ +
+ +
+ +
+ Enhanced I/O Error Handling (EEH) Option Functions + The EEH option requires several additional RTAS calls. In addition, + the Error Injection option RTAS calls are required to be implemented, in + order to be able to test device driver code that implements recovery + based on the EEH option. + See also, + , for additional information + about implementing EEH error recovery. + + + + R1--1. + + For the EEH option: The IOA bus error injection + function of the Error Injection option RTAS call must be implemented + concurrently with the EEH option (that is, the + ioa-bus-error token must exist in the + “ibm,errinjct-tokens” property). + + + + + R1--2. + + For the EEH option: If the EEH option is implemented + for the specified PE configuration address, then calls to the + + ibm,set-eeh-option, ibm,set-slot-reset, and + ibm,slot-error-detail RTAS calls must be governed by + , otherwise if one of the + invalid transitions in + is attempted, then return a + Status as defined by + . + + + + + R1--3. + + If the EEH option is not implemented for + the specified PE configuration address and a call is made to one of the + ibm,set-eeh-option, ibm,set-slot-reset, or + ibm,slot-error-detail RTAS calls, then return a + Status of -3 (parameter error). + + Software Implementation Note: Some transitions in + are made asynchronously to the + OS by the platform (in exceptional cases; see table for details). If + software receives a + Status of -7 (Unexpected state change) on an RTAS + call which is attempting to change state in + , then software should read the + state again via the + ibm,read-slot-reset-state2 RTAS call, in order to + obtain the current state. Some legacy implementations may return a -1 + instead of a -7. + + + + + R1--4. + + For the EEH option: + If the platform + activates the reset to a PE (for example, as part of a recovery action + above the PE), including the case where the platform has temporarily + deactivated and then reactivated the reset, then the platform must hide + such PE state transition(s) from the OS by returning a + Status of 5 (PE is unavailable) with + PE Unavailable Info indicating a non-zero value + (temporarily unavailable) for the + ibm,read-slot-reset-state2 RTAS call, until which + time the required minimum reset active hold time for the hardware within + the PE has been met. + + Software Implementation Note: Relative to the + platform automatically resetting the PE as part of error recovery, as + mentioned in Requirement + , the + PE Recovery Info output of the + ibm,read-slot-reset-state2 RTAS call is provided to + enable the software to determine that such a reset has occurred. + + + + + R1--5. + + For the EEH option: + If the platform + deactivates the reset to a PE, except in the case where the OS has + instructed it to do so with the + ibm,set-slot-reset Function 0, then the platform must + do all the following: + + + + Hide such a deactivation from the OS during the time that the PE + reset is deactivated by returning a + Status of 5 (PE is unavailable) with + PE Unavailable Info indicating a non-zero value + (temporarily unavailable) for the + ibm,read-slot-reset-state2 RTAS call. + + + + Force OS MMIO accesses to the PE during the deactivation time to + look like the PE is reset. + + + + Prevent the PE from introducing errors into the system (for + example, from DMA or due to the reset being deactivated prior to the + proper active hold time). + + + + Reactivate the reset, hiding the reset active hold time as + required by Requirement + , or force the PE into the + permanently unavailable state (return a + Status of 5 (PE is unavailable) with + PE Unavailable Info indicating a zero value for the + ibm,read-slot-reset-state2 RTAS call). + + + + + + + R1--6. + + For the EEH option: The Bridged-I/O EEH option must + be implemented concurrently with the EEH option. + + + + + R1--7. + + For the EEH option: The 64 bit IOA bus error + injection function of the Error Injection option RTAS call must be + implemented concurrently with the EEH option (that is, the + ioa-bus-error-64 token must exist in the + “ibm,errinjct-tokens” property). + + + + + R1--8. + + For the EEH option: The platform must implement the + ibm,configure-pe RTAS call. + + + + + + PE State Transition Table + + + + + + + + + + + + + + Initial PE State + + The state as would be returned from + ibm,read-slot-reset-state2, when no + asynchronous platform transition has occurred. + + + + + + + + Final PE State + + + + + + + + + + 0 + Not Reset + + Load/ + Store Allowed + + Load/ Store allowed means + the Loads or Stores channel is + open to the PE, and not necessarily that the PE itself has its MMIO space + enabled. The components within the PE also contain enable/disable bits + (for example, the PCI configuration space Memory Space and IO Space + enable bits in the PCI header Device Control register). + + + DMA Allowed + + DMA allowed means the DMA channel is open to the PE, if the PE + itself has its DMA enabled. The components within the PE also contain + enable/disable bits (for example, the PCI configuration space Bus Master + enable bit in the PCI header Device Control register). + + + (Normal Operations) + + + + 1 + Reset + + Reset may mean that the PE is being held in the reset state by + a reset signal or Hot Reset (PCI Express), or that it may have been + put into this state by the platform via a PCI Express Function Level + Reset (FLR) in response to the ibm,set-slot-reset + RTAS call. In the case of FLR, the platform makes the pulse of the FLR + look like the Hot Reset case to the OS in terms of the Reset state + (See for more information). + Note that the platform does not monitor writes to the FLR bit of an + IOA, and so OS or Device Driver writes directly to the FLR bit on an + IOA will not affect the PE State as shown in + . + + + + Load/ + Store Disabled + + Load/ Store disabled + means that either the PE is in the MMIO Stopped state or that the PE + is reset, the latter giving the appearance of being MMIO Stopped. + + + DMA Disabled + + DMA disabled means that either the PE is in the DMA + Stopped state or that the PE is reset, the latter giving + the appearance of being DMA Stopped. + + + + + + 2 + Not Reset + + Although the current state is “Not Reset”, + the PE may have been reset by the platform in the process of + getting to this state. The PE Recovery Info + output of the ibm,read-slot-reset-state2 + RTAS call will indicate if the platform has done such a reset. + + + + Load/ + Store Disabled + + In the MMIO Stopped state. + + + DMA Disabled + + In the DMA Stopped state. + + + + + + 4 + Not Reset + + Load/ + Store Allowed + + + DMA Disabled + + + + + + 5 + Temporarily + Unavailable + + Temporarily unavailable is signaled by a non-zero value r + eturned in the PE Unavailable Info of the + ibm,read-slot-reset-state2 RTAS calls. + + + + + + 5 + Permanently Unavailable + + Permanently unavailable is signaled by a zero value + returned in the PE Unavailable Info + of the ibm,read-slot-reset-state2 RTAS calls. + + + + + + + + + + 0 + Not Reset + + Load/ + Store Allowed + + + DMA Allowed + + + (Normal Operations) + + +   + + + + ibm,set-slot-reset + + + Function 1 or 3, or via a hardware + initiated action + + The hardware would not normally initiate this + transition; such implementation would only exist where the + platform only implements EEH Stopped State via a reset + (always) of the PE (that is, only implements states 0, 1, and + 5 of this table), which is not applicable for LoPAR + Compliant platforms. + + + + Hardware causes this state transition when EEH is enabled + and an error occurs or firmware may cause due to higher level + error recovery action + + + Not a valid + transition + + + Platform initiated action + + + + ibm,slot-error-detail + + + Function 2, or platform detected permanent + error + + + + + 1 + Reset + + Load/ + Store Disabled + DMA Disabled + + + + + + ibm,set-slot-reset + + + Function 0 + + The platform also removes the PE from the EEH Stopped + state, if applicable, on the transition from state 1 to state + 0. + + + + + ibm,set-slot-reset + + + Function 1 or 3 + + + Not a valid + transition + + + Not a valid + transition + + + Platform initiated action + + + + ibm,slot-error-detail + + + Function 2, or platform detected permanent + error + + + + + 2 + Not Reset + + Load/ + Store Disabled + + + DMA Disabled + + + + + Not a valid + transition + Must go through + state 4 or state 1 + + + + ibm,set-slot-reset + + + Function 1 or 3, or via a hardware + initiated action + + + + + +   + + + + ibm,set-eeh-option + + + Function 2 + + + Platform initiated action + + + + ibm,slot-error-detail + + + Function 2, or hardware detected permanent + error + + + + + 4 + Not Reset + + Load/ + Store Allowed + + + DMA Disabled + + + + + + ibm,set-eeh-option + + + Function 3 + See Requirement + + + + + + + ibm,set-slot-reset + + + Function 1 or 3, or via a hardware + initiated action + + + + + + Hardware causes this state transition when EEH is enabled + and an error occurs or firmware may cause due to higher level + error recovery action + + +   + + + Platform initiated action + + + + ibm,slot-error-detail + + + Function 2, or platform detected permanent + error + + + + + 5 + Temporarily + Unavailable + + + + + Not a valid + transition + + + Platform initiated action + + + Platform initiated action + + This transition cannot occur if the PE was in the reset + state prior to the platform transition to the temporarily + unavailable state. See Requirement . + . + + + Not a valid + transition + + +   + + + + ibm,slot-error-detail + + + Function 2, or platform detected permanent + error + + + + + 5 + Permanently Unavailable + + + + + Power cycle, + Partition reboot, + or DLPAR + re-assignment + + + Not a valid + transition + + + Not a valid + transition + + + Not a valid + transition + + + Not a valid transition + + +   + + + + +
+ + depicts the four main functions + for controlling a PE’s state: + + + + ibm,set-eeh-option Function 2 for releasing a PE from + the MMIO Stopped State, when the PE is in State 2 (MMIO Stopped State and + DMA Stopped State both active). + + + + ibm,set-eeh-option Function 3 for releasing a PE from + the DMA Stopped State, when the PE is in State 3 (MMIO Stopped State not + active and DMA Stopped State active). + + + + ibm,set-slot-reset Function 0 for releasing a + PE’s reset. + + + + ibm,set-slot-reset Function 1for activating a + PE’s reset. + + + + + Implementation Note: In the last two bullets, above, + for the case of the platform’s use of FLR for resetting the PE, the + meaning of “activating” and “deactivating” the + PE’s reset has slightly different meaning, but the platform makes + the EEH recovery model transparent. See + for more details. + + is a summary of the expected + results of the above four operations. The -7 + Status returns generally will occur for the cases + where the PE state has been changed asynchronously to the OS by the + platform. In these cases, software should read the state again (via the + ibm,read-slot-reset-state2 RTAS call) in order to + determine the current hardware state. + + + PE State Control + + + + + + + + + + + + + + RTAS Call + + + Function + + + Result and Status + + + + + Initial PE State + + The state as would be returned from + ibm,read-slot-reset-state2, when no + asynchronous platform transition has occurred. + + + + + + + + + 0 + Not Reset + + Load/ + Store Allowed + + Load/ Store allowed means + the Loads or Stores channel is + open to the PE, and not necessarily that the PE itself has its MMIO space + enabled. The components within the PE also contain enable/disable bits + (for example, the PCI configuration space Memory Space and IO Space + enable bits in the PCI header Device Control register). + + + DMA Allowed + + DMA allowed means the DMA channel is open to the PE, if the PE + itself has its DMA enabled. The components within the PE also contain + enable/disable bits (for example, the PCI configuration space Bus Master + enable bit in the PCI header Device Control register). + + + (Normal Operations) + + + + 1 + Reset + + Reset may mean that the PE is being held in the reset state by + a reset signal or Hot Reset (PCI Express), or that it may have been + put into this state by the platform via a PCI Express Function Level + Reset (FLR) in response to the ibm,set-slot-reset + RTAS call. In the case of FLR, the platform makes the pulse of the FLR + look like the Hot Reset case to the OS in terms of the Reset state + (See for more information). + Note that the platform does not monitor writes to the FLR bit of an + IOA, and so OS or Device Driver writes directly to the FLR bit on an + IOA will not affect the PE State as shown in + . + + + + Load/ + Store Disabled + + Load/ Store disabled + means that either the PE is in the MMIO Stopped state or that the PE + is reset, the latter giving the appearance of being MMIO Stopped. + + + DMA Disabled + + DMA disabled means that either the PE is in the DMA + Stopped state or that the PE is reset, the latter giving + the appearance of being DMA Stopped. + + + + + + 2 + Not Reset + + Load/ + Store Disabled + + In the MMIO Stopped state. + + + DMA Disabled + + + + 4 + Not Reset + + Load/ + Store Allowed + + + DMA Disabled + + In the DMA Stopped state. + + + + + + 5 + Temporarily + Unavailable + + Temporarily unavailable is signaled by a non-zero value + returned in the PE Unavailable Info of the + ibm,read-slot-reset-state2 RTAS calls. + + + + + + 5 + Permanently Unavailable + + Permanently unavailable is signaled by a zero value + returned in the PE Unavailable Info + of the ibm,read-slot-reset-state2 RTAS calls. + + + + + + + + + + ibm,set-eeh-option + + + + + Function 2 + Release PE for + + Load/Store + + + + Result + + + no-op + + + no-op + + + Transition from state 2 to 4 + + + no-op + + + no-op + + + no-op + + + + + + Status + + A + Status of -3 is returned instead of 0 + or -7 if an invalid PCI configuration address is used. An + invalid PCI configuration address is generally one which is + not a PE address or which is not assigned to the OS. + However, some platforms may allow resetting within the PE + or outside the PE, providing this does not violate other + requirements defined by this architecture. Also, some + legacy implementations may return a -1 or -3 instead of a + -7, but all implementations are required to implement the + -7 + Status, where appropriate. + + + + + -3 + + + -7 + + + 0 + + + -3 + + + -7 + + + -7 + + + + + + Function 3 + Release PE for + DMA + + + Result + + + no-op + + + no-op + + + no-op + + + Transition from state 4 to 0 + + + no-op + + + no-op + + + + + + Status + + + + + + + -3 + + + -7 + + + -7 + + + 0 + + + -7 + + + -7 + + + + + + ibm,set-slot-reset + + + + + Function 0 + Deactivate the + reset to the PE + + In the case of the use of FLR by the platform to reset + the PE, the “activate” and + “deactivate” of the reset has a different meaning + than for the Hot Reset case. For FLR, the platform makes the + pulse of the FLR look like the Hot Reset case to the OS in + terms of the Reset state (See + for more + information). + + + + Result + + + no-op + + + Transition from state 1 to 0 + + The platform also removes the PE from the EEH Stopped + state, if applicable, on the transition from state 1 to state + 0. + + + + no-op + + + no-op + + + no-op + + + no-op + + + + + + Status + + + + + + + + 0 + + + 0 + + + -7 + + + -3 + + + -7 + + + -7 + + + + + + Function 1 or 3 + Activate the + reset to the PE + + + Result + + + + + + Transition from state 0 to 1 + + + no-op + + + Transition from state 2 to 1 + + + Transition from state 4 to 1 + + + no-op + + + no-op + + + + + + Status + + , + + For + Function 3, if + Function 3 is not implemented, then a + Status of -3 is returned. For + Function 3, if implemented in the RTAS + call, but not implemented for the specified PCI + configuration address, then a + Status of -8 is returned. In either of + these cases, the PE state is not changed. If + Function 3 is implemented, then the + platform indicates this by the + + “ibm,reset-capabilities” property in + the OF device tree. + + + + + 0 + + + 0 + + + 0 + + + 0 + + + -7 + + + -7 + + + + +
+ + The PE configuration address ( + PHB_Unit_ID_Hi, PHB_Unit_ID_Low, and config_addr) + for the domain is the PCI configuration address for the PE primary bus + and is the same format as used for the ibm,read-pci-config and + ibm,write-pci-config calls (see Requirement + ), except that the Register + field is set to 0. The PE configuration address is obtained as indicated + in + . + +
+ <emphasis>ibm,set-eeh-option</emphasis> + + This call is used to enable and disable the EEH domain of a PE, to + remove a PE from the MMIO Stopped state to continue + Load and + Store operations to the domain, and to remove a PE + from the DMA Stopped state to continue DMA operations to the domain. The + PE configuration address ( + PHB_Unit_ID_Hi, PHB_Unit_ID_Low, and config_addr) + for the PE is obtained as defined in + . + + + + R1--1. + + For the EEH option: RTAS must implement an + ibm,set-eeh-option call + using the argument call buffer defined by + . + + + Argument Call Buffer + <emphasis>ibm,set-eeh-option</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,set-eeh-option + + + + + + Number Inputs + + + + 4 + + + + + + Number Outputs + + + + 1 + + + + + + Config_addr + + + + PE configuration address (Register fields set to + 0) + + + + + + PHB_Unit_ID_Hi + + + + Represents the most-significant 32-bits of the Unit ID of + the PHB that corresponds to the + config_addr + + + + + + PHB_Unit_ID_Low + + + + Represents the least-significant 32-bits of the Unit ID + of the PHB that corresponds to the + config_addr + + + + + + Function + + + + 0: Disable EEH option for the PE (no-op for PEs with PCI + Express IOAs) + 1: Enable EEH option for the PE + 2: Release the PE for + Load/ + Store operations + 3: Release the PE for DMA operations + 4: Enable EEH io-event interrupt for this PE + 5: Disable EEH io-event interrupt for this PE + + + + + Out + + + + Status + + + + 0: Success + -1: Hardware Error + -3: Parameter Error + -7 Unexpected state change + + + + +
+ + Software and Platform Implementation Note: For + platforms that enable EEH by default, + ibm,set-eeh-option Function 0 (disable EEH) is a + no-op. However, + ibm,set-eeh-option Function 1 (enable EEH) is still + required as a signalling method from the device driver to the platform + that the device driver is at least EEH aware (see Requirement + ). + + + + + R1--2. + + For the EEH option: Software must use the + ibm,get-config-addr-info2 RTAS call, when supported, + to get the EEH domain span of the PE, otherwise software must use the + ibm,read-slot-reset-state2 RTAS call in order to + determine the span, and then software should attempt to perform all + ibm,set-slot-reset + and + + ibm,set-eeh-option + RTAS calls appropriately, based on the EEH + capabilities and as governed by + . + + + + + R1--3. + + For the EEH option: If the EEH option is implemented + for the specified PE configuration address, on a call to the + + ibm,set-eeh-option + with a + + Function + of 0 (disable EEH) the platform must do one of the + following: + + + + If any IOA in the PE is enabled (if any of the Bus Master, Memory + Space or I/O Space bits in the Command Register of the IOA’s + configuration space are 1), then do nothing and return a + Status of 0 (Success). + + + + If the platform allows disabling of EEH and the disabling of EEH + for the PE violates another requirement relative to LPAR, then the + platform must not disable the EEH option for the specified PE + configuration address and must return a -7 (unexpected state change) or a + -1 (hardware error), with -7 preferred. + + + + If the platform allows disabling of EEH and the disabling of EEH + for the PE does not violate the other requirements relative to LPAR, then + clear the MMIO Stopped State and DMA Stopped State, and disable the EEH + option, for the specified PE configuration address. + + + + If the default for the platform is EEH enabled, then do nothing + and return a + Status of 0 (Success). + + + + + + + R1--4. + + For the EEH option: + If the OS allows + the DMA to be enabled for a PE that is in the DMA Stopped state without + the use of a reset operation (that is, the use of the + ibm,set-eeh-option with a + Function of 3), the device driver must first do all + necessary cleanup of its IOA to prevent the IOA from doing anything + destructive when it starts DMA again. + + + + + R1--5. + + For the EEH option: If a device driver is going to + enable EEH and the platform has not defaulted to EEH enabled, then it + must do so before it does any operations with its IOA, including any + configuration cycles or + Load or + Store operations. + + + + + R1--6. + + For the EEH option: If an EEH domain is enabled for a + PE via the ibm,set-eeh-option RTAS call and if there are multiple IOAs or + one or more multi-function IOAs in that PE, and if these functions are + supported by multiple device drivers, then all of the device drivers for + all the functions in that PE must be EEH enabled and be capable of + coordinating EEH recovery procedures. + + Software implementation Note: Protection against + startup errors (configuration cycles, etc.), are every bit as important + as protection against errors during normal operations. Although the + quantity of operations is not as great, there is more of a chance of + latent errors showing up during the startup phase. + + + + + R1--7. + + For the EEH option: If the Slot Level EEH Event + Interrupt option is not implemented for the PE, then return a + Status of -3 if + Function 4 or 5 is attempted. + + + + + R1--8. + + For the EEH with the Slot Level EEH Event Interrupt + option: + Function 4 and 5 must be implemented for all PE under + nodes that contain the + “ibm,io-events-capable” property. + + + + +
+ +
+ <emphasis>ibm,set-slot-reset</emphasis> + + This call is used to reset a PE. The PE configuration address ( + PHB_Unit_ID_Hi, PHB_Unit_ID_Low, and config_addr) + for the PE is obtained as defined in + . All PEs have the capability + of being reset independently. Resets outside or within the PE are not + architected, but may be allowed by the platform implementation, providing + that it does not violate other requirements of this architecture. + The platform may use one of two methods to reset a PCI Express PE, + when the + ibm,set-slot-reset RTAS call is made with the + Function 1/ + Function 0 (activate the reset/deactivate the + reset). + + + + If the PE is a single function of a multi-function IOA, then the + Function Level Reset (FLR) option is required to be implemented by the + function, and the platform uses FLR to reset the function. When the + platform uses FLR instead of Hot Reset to reset a PCI Express PE, the + platform provides the + “ibm,pe-reset-is-flr” property in the + function’s OF Device Tree node, and provides the same EEH recovery + model to the software, as in the Hot Reset case, and as defined by + . The property is provided in + the case where there may be slightly different device-specific reset + recoveries by the software for the FLR case. + + Software Implementation Note: The platform does not + monitor writes to the FLR bit of an IOA, and so OS or Device Driver + writes directly to the FLR bit on an IOA will not affect the PE State as + shown in + . + + + + Otherwise, a PCI Express Hot Reset is used. + + + + + + R1--1. + + For the EEH option: The + ibm,set-slot-reset call must be implemented using the + argument call buffer defined by + . + + + + Argument Call Buffer + <emphasis>ibm,set-slot-reset</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,set-slot-reset + + + + + + Number Inputs + + + + 4 + + + + + + Number Outputs + + + + 1 + + + + + + Config_addr + + + + PE configuration address (Register fields set to + 0) + + + + + + PHB_Unit_ID_Hi + + + + Represents the most-significant 32-bits of the Unit ID of + the PHB that corresponds to the + config_addr + + + + + + PHB_Unit_ID_Low + + + + Represents the least-significant 32-bits of the Unit ID + of the PHB that corresponds to the + config_addr + + + + + + Function + + + + 0: Deactivate the reset to the PE + 1: Activate the reset to the PE (for PCI Express, if the + platform uses FLR to reset the PE, the platform provides the + “ibm,pe-reset-is-flr” property + in the function’s OF Device Tree node) + 3: (optional) Activate the reset to the PE, using a PCI + Express Fundamental Reset + + + + + Out + + + + Status + + + + 0: Success + -1: Hardware Error + -3: Parameter Error + -7: Unexpected state change + -8: Fundamental Reset not defined for this configuration + address + + + + +
+ + + + + R1--2. + + For the EEH option: After activation of the reset ( + Function 1 or 3), software must delay the + deactivation of the reset ( + Function 0) to that PE via the + ibm,set-slot-reset call, + until the minimum reset signal active time has elapsed, as designated by + the bus specifications for the particular type bus or buses involved (100 + millisecond for PCI). + + Software Implementation Notes: + + + + + The device driver is responsible for any additional clean up + required beyond that provided by a reset to the IOA. For PCI Express, the + clean up may be slightly different based on whether the platform used FLR + or Hot Reset to reset the PE. When FLR is used, the platform provides the + “ibm,pe-reset-is-flr” property in the + function’s OF Device Tree node. + + + + The software is responsible for quiescing (stopping) any MMIO + Load and + Store activities to the PE prior to resetting the + PE. + + + + If the platform uses FLR to implement the PE reset, software may + need to understand that this is a pulse and not a solid level, such that + the adapter is not held at reset during the time from the call with + Function 1 and the call with + Function 0. + + + + + + + R1--3. + + For the EEH option: After deactivation of the reset ( + Function 0), software must delay access to that PE + until the minimum time after reset that is required for the PE to be come + stable has elapsed, as designated by the bus specifications for the + particular type bus or buses involved (for example, 1.5 seconds for PCI + Express). + + Software Implementation Notes: + + + + + Different implementations of PCI Express may require different + amounts of delay in order to traverse the I/O fabric since individual + component delays are plug-in card specific. + + + + The ibm,read-slot-reset-state2 RTAS call returns a + PE Reset State of 5 (PE is unavailable) while any + reset delay time is happening for hardware outside the PE. + + + + + + + R1--4. + + For the EEH option: If the + ibm,set-slot-reset call is called with a + Function of 0 (deactivate) and any reset to the reset + domain specified by the + PE configuration address is active, then the RTAS + call must de-activate all resets to that PE configuration address. + + + + + R1--5. + + For the EEH option: If the + ibm,set-slot-reset call is called with a + Function of 0 (deactivate) and there is no operation + to be performed (for example, the reset to the reset domain specified by + the PE configuration address is not active), then the RTAS call must + return a + Status of 0 (success). + + + + + R1--6. + + For the EEH option: When the + ibm,set-slot-reset call is called with a + Function of 1 or 3 (activate) with a valid PHB Unit + ID and config_addr and it is the case that FLR is not being used by the + platform to reset the PE, then the RTAS call must activate the reset to + the reset domain as designated by the PE configuration address, if not + already activated. + + + + + R1--7. + + For the EEH option: When the + ibm,set-slot-reset RTAS call implements + Function 3, the platform must also provide the + “ibm,reset-capabilities” property in the + RTAS node of the OF device tree. + + + + + R1--8. + + For the EEH option: When the + ibm,set-slot-reset call is called with a + Function of 0 (deactivate) with a valid PHB Unit ID + and config_addr and if the corresponding PE is in the MMIO Stopped or DMA + Stopped state, then the RTAS call must bring that PE as designated by the + PE configuration address out of the MMIO Stopped and DMA Stopped states + and clear any applicable platform EEH status state. + + + + + R1--9. + + For the EEH option: When the platform uses FLR to + reset a PCI Express PE ( + ibm,set-slot-reset call with a + Function of 1(activate) followed by a call with + Function 0 (deactivate)), then the platform must + provide the + “ibm,pe-reset-is-flr” property in the + function’s OF Device Tree node, and the platform must always use + FLR to reset a PE which contains this property in the OF Device + Tree. + + + + + R1--10. + + For the EEH option: + For a PCI Express + PE, the platform must provide the EEH recovery model to the software, as + defined by + , regardless of whether Hot + Reset or FLR is used to reset the PE. + + + + +
+ +
+ <emphasis>ibm,read-slot-reset-state2</emphasis> + This call queries the state of a PE, and dynamically determines + whether a PCI configuration address corresponds to a PE primary bus (that + is, if it is the PE configuration address). In addition, when the + PE Reset State parameter is a 5 (PE is unavailable), + then the + PE Unavailable Info indicates an approximate amount + of time for which the PE might be unavailable. The PE configuration + address ( + PHB_Unit_ID_Hi, PHB_Unit_ID_Low, and config_addr) + for the PE is obtained as defined in + . + When the + ibm,get-config-addr-info2 RTAS call is implemented, + that call can be used instead of this one to determine the PE + configuration address. See + and + . + + + + R1--1. + + ibm,read-slot-reset-state2 call + must be implemented using the argument call buffer defined by + . + + + Argument Call Buffer + <emphasis>ibm,read-slot-reset-state2</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,read-slot-reset-state2 (see Firmware + Implementation note, below) + + + + + + Number Inputs + + + + 3 + + + + + + Number Outputs + + + + 4: Always allowed. + 5: May be allowed, depending on the value of the + + “ibm,read-slot-reset-state-functions” property + in the + RTAS node of the device tree ( + ). + + + + + + Config_addr + + + + Configuration Space Address (Register fields set to + 0) + + + + + + PHB_Unit_ID_Hi + + + + Represents the most-significant 32-bits of the Unit ID of + the PHB that corresponds to the + config_addr + + + + + + PHB_Unit_ID_Low + + + + Represents the least-significant 32-bits of the Unit ID + of the PHB that corresponds to the + config_addr + + + + + Out + + + + Status + + + + 0: Success + -3: Parameter Error + + + + + + PE Reset State + + + + Except for a + PE Reset State of 5, this output is not + valid unless the + Config_addr Capabilities output is a 1 and + the + Status is a 0. + 0: Reset deactivated and the PE is not in the MMIO + Stopped or DMA Stopped state + 1: Reset activated and the PE is not in the MMIO Stopped + or DMA Stopped states + 2: The PE is in the MMIO Stopped and DMA Stopped states + with the reset deactivated and the + Load/ + Store path is disabled + 4: The PE is in the DMA Stopped state with the reset + deactivated and the + Load/ + Store path is enabled + 5: PE is unavailable + + + + + + Config_addr Capabilities + + + + This output is not valid if the + PE Reset State is a 5. + 0: EEH not supported for the + Config_addr + 1: EEH supported for the + Config_addr + + + + + + PE Unavailable Info + + + + This output is not valid unless the + Config_addr Capabilities output is a 1 and + the + PE Reset State is a 5 and the + Status is a 0, in which case the value of + this parameter is a 0 if the PE is permanently unavailable, and + non-zero if a recovery is in progress and there is an expected + availability after the recovery; the non-0 value in this case + is the number of milliseconds that the recovery is expected to + take. + + + + + PE Recovery Info + + + This output is only valid if the + + “ibm,read-slot-reset-state-functions” property + in the + RTAS node of the device tree indicates that + it is implemented and the call is made with a + Number Outputs of at least 5 and the + PE Reset State is a value of 2. This is a + 32-bit field with bit significance, as follows: +   + Bits 0:27 - Reserved +   + Bits 28:29 - PE platform reset type. Only valid when bit + 31 of this field is a value of 1. + Bits 28:29 = 0b00: Firmware does not implement these + bits. Reset type is most likely a Hot Reset. + Bits 28:29 = 0b01: Platform used a Hot Reset to reset the + PE. + Bits 28:29 = 0b10: Platform used a Fundamental Reset to + reset the PE. + Bits 28:29 = 0b11: Platform used an FLR to reset the + PE. +   + Bit 30 - Retry Count Hint + Bit 30 = 0: Either the PE associated with the + Config_addr was the source of this PE + entering the + PE Reset State of 2, or the platform has + not determined whether this PE was the source or not. + Bit 30 = 1: The platform has determined that the PE + associated with the + Config_addr was not the source of this PE + entering the + PE Reset State of 2. That is, setting this + bit indicates that this PE entered the + PE Reset State of 2 as a side-effect of + some error outside of this PE’s domain. Software may use + this hint to not count this occurrence of the + PE Reset State of 2 as part of any EEH + error recovery retry count that it might be keeping for this + PE. +   + Bit 31 - Reset Status + Bit 31 = 0: PE was not reset as a result of the platform + transition to + PE Reset State of 2. + Bit 31 = 1: PE was reset as a result of the platform + transition to + PE Reset State of 2. If the PE is not below + a node marked with the special value of the + “status” property of + “reserved”, then after + deactivation of the platform-initiated PE reset, the platform + is required to delay access to that PE until the minimum time + after reset that is required for the PE to be come stable has + elapsed, as designated by the bus specifications for the + particular type bus or buses involved (for example, 1.5 seconds + for PCI Express), by returning + PE Reset State of 5 with + PE Unavailability Info non-zero + (temporarily unavailable) until that time has elapsed). If the + PE is below a node marked with the special value of the + “status” property of + “reserved”, then after + deactivation of the platform-initiated PE reset, the firmware + immediately (without delay) transitions the PE to the + PE Reset State of 2, and it is the + controlling software that is required to do the bus-specific + delays. + + + + +
+ + Firmware Implementation Note: The argument call + buffer structure and requirements for this call are the same as for the + old (removed from this architecture) + ibm,read-slot-reset-state call, except for the last + output parameter. Therefore, it is possible for platforms that still + require the old + ibm,read-slot-reset-state RTAS call to implement the + ibm,read-slot-reset-state and + ibm,read-slot-reset-state2 calls with the same RTAS + token and use the number of output parameters to determine whether or not + to implement the PE + Unavailable Info parameter. + + Platform Implementation Notes: + + + + + The ibm,read-slot-reset-state2 RTAS call only returns a + PE Reset State of 1 (Reset activated and the PE is + not in the MMIO Stopped or DMA Stopped state) when the reset may be + removed by software; that is, if the error is potentially recoverable. If + the firmware has detected a hardware error that is such that the reset to + the device cannot be removed or is not safe to remove, the + ibm,read-slot-reset-state2 does not return a + PE Reset State of 1, but instead returns a + PE Reset State of 5 (PE is unavailable) along with PE + Unavailable Info of 0 (PE is permanently + unavailable). + + + + The ibm,read-slot-reset-state2 RTAS call should never + return a -1 (hardware error), but should instead return a + PE Reset State of 5 (PE is unavailable) with a + PE Unavailable Info of 0 (PE is permanently + unavailable). + + + + + + + R1--2. + + The ibm,read-slot-reset-state2 RTAS call must return a + Reset State value of 5 (PE is unavailable) under any + of the following conditions: + + + + Firmware has + determined that communications with the PE is not available or the path + to the PE cannot be traversed at the current time + + + + The ibm,slot-error-detail RTAS call has been called with + a + Function of 2, and none of the resetting conditions + specified in Requirement + have been met. + + + + + Software Implementation Notes: + + + + + The condition under Requirement + + may be temporary, with a + recovery time in the range of seconds (for example, as little as 3 + seconds or up to couple of minutes). Software may chose to delay the time + indicated in the + PE Unavailable Info and issue the + ibm,read-slot-reset-state2 call again when a + temporary condition exists. The condition may also be clearable with a + power cycle of the PE, in which case the firmware may return a + Status of 990x to the + set-power-level RTAS call, to delay long enough to + clear the temporary condition. + + + + Config_addr Capabilities may be indeterminate when + the PE Reset State of 5 (PE is unavailable) is returned. + Software should ignore the + Config_addr Capabilities return when the + PE Reset State of 5 is returned. + + + + + + + R1--3. + + If the + ibm,read-slot-reset-state2 RTAS call must return a + PE Reset State value of 5 (PE is unavailable) then it + must indicate in the + PE Unavailable Info parameter one of the + following: + + + + A value of zero, if there is no error recovery in progress that + makes the PE available in any predictable amount of time (that is, the PE + is “permanently” unavailable; for example, until a power + cycle or until a repair action). + + + + A non-zero value, indicating the approximate time in + milliseconds after which the path to the PE is expected to become + available again. + + + + + + + R1--4. + + The + ibm,read-slot-reset-state2 RTAS call must return a + Config_addr Capabilities of 1 (EEH supported for the + Config_addr) for every + Config_addr within a PE and for the PE configuration + address. + + + + + R1--5. + + The + ibm,read-slot-reset-state2 RTAS call must comply with + the state transitions defined in + . + + + + +
+ +
+ <emphasis>ibm,get-config-addr-info2</emphasis> + + This call is used obtain information about fabric configuration + addresses, given the PCI configuration address. See + for more information on PEs and + determining PE configuration addresses. + The PCI configuration address ( + PHB_Unit_ID_Hi, PHB_Unit_ID_Low, and config_addr) + for the call is defined by + . + + + + R1--1. + + The + ibm,get-config-addr-info2 call + must be implemented using the argument call buffer defined by + . + + + Argument Call Buffer + <emphasis>ibm,get-config-addr-info2</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,get-config-addr-info2 (see Firmware + Implementation note, below) + + + + + + Number Inputs + + + + 4 + + + + + + Number Outputs + + + + 2 + + + + + + Config_addr + + + + Configuration Space Address (Register fields set to + 0) + + + + + + PHB_Unit_ID_Hi + + + + Represents the most-significant 32-bits of the Unit ID of + the PHB that corresponds to the + config_addr + + + + + + PHB_Unit_ID_Low + + + + Represents the least-significant 32-bits of the Unit ID + of the PHB that corresponds to the + config_addr + + + + + + Function + + + + See + for available + functions. + + + + + Out + + + + Status + + + + 0: Success + -3: Parameter Error + + + + + + Info + + + + See + for values. + + + + +
+ + + + + R1--2. + + The + ibm,get-config-addr-info2 RTAS call must return the + Data output as per + . + + + Input and + <emphasis>ibm,get-config-addr-info2 Function</emphasis> + <emphasis>Info</emphasis> Output + + + + + + + + + + Function Input + + + + + Definition + + + + + + Info Output + + + + + + + + 0 + + + Get PE configuration address + + + PE configuration address (as defined by + ). Result returned in + + Info output is: + Equal to the + Config_addr input if there is no bridge or + switch between the IOA function (endpoint) and the PE primary + bus. + Equal to the + Config_addr of the PE primary bus if there + is a bridge or switch between the IOA function and the PE + primary bus. + Undefined if + Config_addr is not in a PE (query for PE + state by using + Function 1 first or by + ibm,read-slot-reset-state2 RTAS call). A + Status of -3 (Parameter Error) is returned + in this case, also. + + + + + 1 + + + Query shared PE state + + + 0: + Config_addr is not in a PE (EEH not + supported for the + Config_addr). + 1: Not shared (Only one IOA function in the PE). + 2: Shared (More than one IOA function in the PE). + + + + +
+ + + + +
+ +
+ <emphasis>ibm,slot-error-detail</emphasis> + + This call combines device driver information, as gathered by the + device driver prior to this call, with information derived by firmware + from the platforms I/O infrastructure to create a detailed event log + concerning a recoverable EEH event. In this way, both OS and platform + maintenance applications have access to all the information about a given + event. In addition, the OS can mark a PE configuration address as being + in an unavailable state due to excessive errors. + The caller supplies the device driver information, referenced by + the + Device_Driver_Error_Buffer argument. The + Returned_Error_Buffer argument points to a buffer + that this call fills with valid error log data as defined in the error + log format section. Different platforms log using different versions of + the error logging format. The error log data may include platform + specific data as well as device driver data passed in the + Device_Driver_Error_Buffer. Regardless of the error + log version used, the data in the + Returned_Error_Buffer is in an extended log format as + defined in + . When the call returns data + for version 6 or greater, the device driver error buffer data is included + as the last User Data section. The device driver data in the return + buffer may be truncated from what is passed by the device driver or + completely eliminated as necessary to ensure that the returned buffer + length is not exceeded. + The + Config_addr supplied is the PE configuration address + ( + PHB_Unit_ID_Hi, PHB_Unit_ID_Low, and config_addr) + for the PE, obtained as defined in + , or a configuration address + within the PE. The I/O fabric information that is captured by the + platform consists of useful PCI configuration state at and above the + supplied + Config_addr. + This RTAS call supports both plug-in PCI cards and built-in PCI + IOAs. + In this section, the term unavailable, when applied to a PE, means + that + ibm,read-slot-reset-state2 would return a PE Reset + State of 5 (PE is unavailable) at the current time. + + + + R1--1. + + For the EEH option: The + argument call buffer for the + ibm,slot-error-detail call must correspond to the + definition given in + . + + + Argument Call Buffer + <emphasis>ibm,slot-error-detail</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,slot-error-detail + + + + + + Number Inputs + + + + 8 + + + + + + Number Outputs + + + + 1 + + + + + + Config_addr + + + + Configuration address (Register numbers set to 0) + + + + + + PHB_Unit_ID_Hi + + + + Represents the most-significant 32-bits of the Unit ID of + the PHB that corresponds to the + config_addr + + + + + + PHB_Unit_ID_Low + + + + Represents the least-significant 32-bits of the Unit ID + of the PHB that corresponds to the + config_addr + + + + + + Device_Driver_Error_Buffer + + + + Real address of an error log buffer containing device + driver debug data. This data is integrated into the final error + log + + + + + + Device_Driver_Error_Buffer_Length + + + + Length of the + Device_Driver_Error_Buffer + + + + + + Returned_Error_Buffer + + + + Real address of an error log buffer to contain a + compliant error log entry composed by the RTAS + + + + + + Returned_Error_Buffer_Length + + + + Length of the + Returned_Error_Buffer + + + + + + Function + + + + 1: Temporary Error + 2: Permanent Error + + + + + Out + + + + Status + + + + 1: No Error Log Returned + 0: Success + -1: Hardware Error (cannot create log) + + + + +
+ + + + + R1--2. + + The + Returned_Error_Buffer format must be the same as + implemented by + event-scan on the platform. + + + + + R1--3. + + To prevent standard error log record + truncation, the + Returned_Error_Buffer_Length must equal the value of + the OF device tree property + “rtas-error-log-max”. + + + + + R1--4. + + If the PE corresponding to the + Config_addr is in the MMIO Stopped or DMA Stopped + state, then the + ibm,slot-error-detail RTAS call must return a + Status of 0 and an error log that defines the FRU or + FRUs to which the error is isolated. + + + + + R1--5. + + If the communications with the + Config_addr is not available, the path to the + Config_addr cannot be traversed at the current time, + or this call has previously made with a + Function of 2 and none of the conditions that reset + this state have been met (that is the PE is unavailable), then the + ibm,slot-error-detail RTAS call must return a + Status of 0 and an error log that defines the FRU or + FRUs to which the error is isolated. + + + + + R1--6. + + If the conditions in Requirements + and + are not met, then the + ibm,slot-error-detail RTAS call must return a + Status of 1, no error found, with no error log entry + returned. + + Software and Platform Implementation Note: In some + cases, the platform may return an information-only error log to meet + Requirements + and + . For example, in some + implementations this might be appropriate if the actual error was already + logged via another RTAS call or this call was previously made with a + Function of 2 and none of the conditions that reset + this state have been met. + + + + + R1--7. + + Once a PE is unavailable and in the + absence of any state-resetting action by the OS that clears the + corresponding PE configuration address EEH error (for example, reset or + power cycle), the platform must return an error log in response to the + ibm,slot-error-detail RTAS call. + + + + + R1--8. + + Once a PE has experienced a + state-resetting action by the OS that clears the corresponding PE + configuration address EEH error (for example, reset or power cycle), that + makes the PE available, the platform must return a + Status of 1, no error found, with no error log entry + in response to the + ibm,slot-error-detail RTAS call. + + + + + R1--9. + + If the ibm,slot-error-detail RTAS call + Device_Driver_Error_Buffer_Length argument is + non-zero, indicating the existence of optional device driver error data, + the referenced buffer must contain an extended event log as defined in + . + + + + + R1--10. + + (Requirement Number Reserved For + Compatibility) + + + + + R1--11. + + When the + ibm,slot-error-detail RTAS call returns an extended + log debug record in the buffer specified by the + Returned_Error_Buffer argument as mandated by + Requirements + and + it must truncate the record at + the length specified by the + Returned_Error_Buffer_Length argument. + + + + + R1--12. + + If a Function of 2 is passed to the + ibm,slot-error-detail RTAS call, RTAS must + unconditionally set the state of the PE corresponding to the + Config_addr to permanently unavailable; that is, any + subsequent calls to + ibm,read-slot-reset-state2 return a PE Reset State of + 5 (PE is unavailable) with the + PE Unavailable Info argument set to zero. + + + + + R1--13. + + RTAS must not change a PE Reset state + of permanently unavailable unless one of the following occur: + + + + A PCI Hot Plug condition for the slot is encountered (as + determined by the power being turned off and then on for the slot) + + + + The power domain is power cycled for another reason (for + example, a power down of the OS image that owns the IOA) + + + + The state is cleared by a partition reboot or a dynamic LPAR + reassignment of the PCI configuration address. + + + + + + + R1--14. + + After a PE enters the MMIO and DMA + Stopped States due to an error, the platform must keep cached error + information relative to that error, for reporting via the + ibm,slot-error-detail RTAS call, until any one of the + following events occurs: + + + + The ibm,slot-error-detail RTAS call is called and the + error information is returned. + + + + The reset to the PE is activated via the + ibm,set-slot-reset RTAS call. + + + + The removal of the PE from the DMA Stopped State via + Function 3 of the + ibm,set-eeh-option RTAS call. + + + + The start of a DR operation as signalled by the calling of + set-indicator with + isolation-state set to isolate. + + + + + + + R1--15. + + Prior to calling the + ibm,slot-error-detail RTAS call, the PE which + includes the + Config_addr must not be in the MMIO Stopped State, if + the maximum amount of useful information is to be captured, as defined by + Requirement + . + + + + + R1--16. + + The firmware implementing the + ibm,slot-error-detail is responsible for gathering + the PCI fabric configuration space registers, including those at the + specified + Config_addr, and also any other non-PCI I/O fabric + registers that might be useful for debug purposes (for example, internal + PHB registers), with the suggested appropriate minimum set of PCI + configuration registers captured for each PCI device being as indicated + in + . + + + Suggested Minimum PCI Configuration Registers to + Capture for + <emphasis>ibm,slot-error-detail</emphasis> + + + + + + + + + + Data Structure + + + + + Offset within the Data + Structure + + + + + Register + + + + + + + + Base PCI Configuration Space Header + (for all PCI devices) + + + 0x00 + + + Vendor ID + + + + + 0x02 + + + Device ID + + + + + 0x04 + + + Command + + + + + 0x06 + + + Status + + + + + 0x08 + + + Revision ID + + + + + 0x09 + + + Class Code + + + + + Type 0 Configuration Space Header + (for non-PCI bridges only) + + + 0x2C + + + Subsystem Vendor ID + + + + + 0x2E + + + Subsystem ID + + + + + Type 1 Configuration Space Header + (for PCI bridges only) + + + 0x1E + + + Secondary Status + + + + + PCI-X Capabilities List + (for all PCI-X devices) + + + 0x02 + + + PCI-X Command (Type 0 Configuration Header) + PCI-X Secondary Status (Type 1 Configuration + Header) + + + + + 0x04 + + + PCI-X Status (Type 0 Configuration Header) + PCI-X Bridge Status (Type 1 Configuration Header) + + + + + PCI Express Capabilities Structure + (for all PCI Express devices) + + + 0x02 + + + PCI Express Capabilities + + + + + 0x04 + + + Device Capabilities + + + + + 0x08 + + + Device Control + + + + + 0x0A + + + Device Status + + + + + 0x0C + + + Link Capabilities + + + + + 0x10 + + + Link Control + + + + + 0x12 + + + Link Status + + + + + 0x14 + + + Slot Capabilities + + + + + 0x18 + + + Slot Control + + + + + 0x1A + + + Slot Status + + + + + 0x1C + + + Root Control + + + + + 0x1E + + + Root Capabilities + + + + + 0x20 + + + Root Status + + + + + Advanced Error Reporting Capability + (for all devices implementing AER) + + + 0x00 + + + PCI Express Enhanced Capability Header + + + + + 0x04 + + + Uncorrectable Error Status + + + + + 0x08 + + + Uncorrectable Error Mask + + + + + 0x0C + + + Uncorrectable Error Severity + + + + + 0x10 + + + Correctable Error Status + + + + + 0x14 + + + Correctable Error Mask + + + + + 0x18 + + + Advanced Error Capabilities and Control + + + + + 0x1C + + + Header Log + + + + + 0x2C + + + Root Error Command (Root Ports only) + + + + + 0x30 + + + Root Error Status (Root Ports only) + + + + + 0x34 + + + Correctable Error Source Identification (Root Ports + only) + + + + + 0x36 + + + Error Source Identification (Root Ports only) + + + + +
+ + + + + R1--17. + + If the + ibm,slot-error-detail RTAS call is made with the PE + in the PE state of 2 (as defined by + ), then the platform must not + remove the PE from that state in order to probe the PCI fabric. + + + + + R1--18. + + If the ibm,slot-error-detail RTAS call is made with the PE + in the PE state of 4 (as defined by + ), then the + ibm,slot-error-detail RTAS call must return with the + PE in the PE state of 4, except that if an error occurs in the course of + probing the PCI fabric that requires a reset of the PE by the platform, + then discontinue probing, return a Status of 0 or 1 (as appropriate), and + return the PE in the PE state of 2. + + Software and Platform Implementation Notes: + + + + + In Requirement + , it is possible, as a part of + the firmware probing the fabric, that the PE will transition temporarily + to a PE state of 2, in the case where another EEH event occurs as part of + the firmware probing the fabric. If the EEH event does not require a + reset of the PE for these subsequent EEH events, then the firmware may + transition the PE back to the PE state of 4, to continue probing. Several + of these PE state 4->2->4 events may occur as a result of probing + the fabric. + + + + In Requirement + if an EEH event occurs as a + result of probing that fabric that results in a reset of the PE, the + returned PE state of 2 does not necessarily need to be checked for by the + software on return from the call. The case where this occurs is expected + to be rare, and probably signals a non-transient error. In this case the + software can continue on with the recovery phase of the EEH processing, + and will eventually hit the same event on further processing. + + + + + + +
+ +
+ +
+ Bridged-I/O EEH Support Option + + The Bridged-I/O EEH Support Option provides RTAS calls for + restoring the boot time configuration of EEH error domains that contain + multiple IOAs or multi-function IOAs (for example, mult-function I/O + cards which are constructed by placing multiple IOAs beneath a PCI to PCI + bridge or PCI Express switch). During EEH recovery, the IOA is subject to + a full hardware reset. These calls recreate any configuration changes, + from full hardware reset, that the firmware normally makes during + platform boot prior to turning the IOA over to the client program plus + any subsequent changes made via ibm,change-msi. Once these calls restore + the IOA initial configuration plus interrupts changes, it is the + responsibility of the device driver, as part of its EEH recover + procedure, to finish the configuration restoration with any non + interrupts changes it makes to the IOA. + Bridge types supported by these calls include PCI to PCI bridges + (for example, a PCI to PCI bridge on an I/O plug-in card) and PCI Express + bridges and switches. + This option does not address the initialization of bridges and + switches which are outside of all PEs. Those are the platform’s + responsibility. + If there is no supported bridge or switch at the PE configuration + address specified by the input parameters, then these calls return a + “success” without configuring anything, and therefore these + calls can be made for all EEH recovery events, regardless of the type of + I/O present. The PE configuration address ( + PHB_Unit_ID_Hi, PHB_Unit_ID_Low, and config_addr) + for the PE is obtained as defined in + . + + Software Implementation Note: Neither + ibm,configure-bridge nor + ibm,configure-pe restores changes to an IOA’s + post boot configuration registers except as made through the + ibm,change-msi RTAS call (for example, to the point + of being able to issue PCI memory space MMIO operations to the IOA, or + perform DMA operations from the IOA). It is the software’s + responsibility to restore any post boot non interrupt changes it made to + the IOA’s PCI configuration space registers after calling one of + these two RTAS calls. + +
+ <emphasis>ibm,configure-bridge</emphasis> + + + + R1--1. + + For the Bridged-I/O EEH Support option: The + ibm,configure-bridge call + must implement the argument call buffer defined by + . + + + Argument Call Buffer + <emphasis>ibm,configure-bridge</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,configure-bridge + + + + + + Number Inputs + + + + 3 + + + + + + Number Outputs + + + + 1 + + + + + + Config_addr + + + + PE configuration address (Register fields set to + 0) + + + + + + PHB_Unit_ID_Hi + + + + Represents the most-significant 32-bits of the Unit ID of + the PHB that corresponds to the + config_addr + + + + + + PHB_Unit_ID_Low + + + + Represents the least-significant 32-bits of the Unit ID + of the PHB that corresponds to the + config_addr + + + + + Out + + + + Status + + + + 990x: Extended delay where x is a number 0-5 (see + Software Implementation note below) + 0: Success + -3: Parameter Error + + + + +
+ + Software Implementation Note: When the 990x + Status is returned, it is suggested that software + delay for 10 raised to the x milliseconds (where x is the last digit of + the 990x return code), before calling + ibm,configure-bridge again. However, software may + issue the + ibm,configure-bridge call again either earlier or + later than this. + + Firmware Implementation Note: + + + + + This call needs to limit the long busy to 9900-9902 with at most + a total of 1/5 second before the + ibm,configure-bridge succeeds. Any longer delays may + cause subsequent hardware or application failures. + + + + For hardware errors, return a + Status of 0 (Success). Hardware errors are + subsequently discovered by further accesses to the PE and additional EEH + events. + + + + + + + R1--2. + + The caller of + ibm,configure-bridge must + provide the PE configuration address, otherwise the RTAS call returns a + -3, “Parameter Error”. + + + + + R1--3. + + The ibm,configure-bridge call + must set up all the PCI to PCI bridges, PCI Express bridges, and PCI + Express switches within the PE, the way they were delivered at boot time + with any modifications made to it via RTAS calls after boot, and must do + so with a single sequence of calls to + ibm,configure-bridge. + + + + + R1--4. + + The ibm,configure-bridge call + must only return a + Status of 990x if one of the following conditions is + true: + + + + The operation was not started. + + + + Firmware is able to restart the same call for this PE even when + other intervening calls to + ibm,configure-bridge have occurred (That is, OSs are + not required to serialize calls to + ibm,configure-bridge). + + + + + + + R1--5. + + Software must + complete all MMIO operations to the IOAs within a PE prior to calling the + ibm,configure-bridge RTAS call for a PE and must not + issue new MMIO operations to the IOAs within the specified PE until after + the RTAS call is complete. + + + + + R1--6. + + On return from the + ibm,configure-bridge RTAS call, the platform must + have the PE in the same EEH state (as defined by + ) as when the call was made, + except that if an error occurs in the course of probing the PCI fabric + that requires a reset of the PE by the platform, then discontinue + probing, return a + Status of 0 or 1 (as appropriate), and return the PE + in the PE state of 2. + + + + + + Software and Platform Implementation Note: + + + + + Given Requirements + and + , it is permissible for the + platform to temporarily transition the PE from a PE state of 2 to PE + state of 4, if the call is made with a PE state of 2 but the hardware + requires a PE state of 4 to get access to the PCI fabric. It is also + permissible for the platform to go through several of these state changes + during the execution of the call if there are errors that occur during + the course of probing the PCI fabric that put the PE back into the PE + state of 4. + + + + In Requirement + if an EEH event occurs as a + result of probing that fabric that results in a reset of the PE, the + returned PE state of 2 does not necessarily need to be checked for by the + software on return from the call. The case where this occurs is expected + to be rare, and probably signals a non-transient error. In this case the + software can continue on with the recovery phase of the EEH processing, + and will eventually hit the same event on further processing. + + + +
+ +
+ <emphasis>ibm,configure-pe</emphasis> + This call has about the same semantics as the + ibm,configure-bridge RTAS call, except that + it: + + + + Has the additional semantics of bypassing the configuration + process if the PE has previously not been reset by the platform as a + result of entering the EEH Stopped State. + + + + Configures all the configurations spaces within the PE, + including those of the endpoint devices within the PE (see Requirement + ). + + + + Thus, this RTAS call can be made at the beginning of any EEH + processing. + + + + R1--1. + + For the Bridged-I/O EEH Support option: The + ibm,configure-pe call must implement the argument + call buffer defined by + . + + + Argument Call Buffer + <emphasis>ibm,configure-pe</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,configure-pe + + + + + + Number Inputs + + + + 3 + + + + + + Number Outputs + + + + 1 + + + + + + Config_addr + + + + PE configuration address (Register fields set to + 0) + + + + + + PHB_Unit_ID_Hi + + + + Represents the most-significant 32-bits of the Unit ID of + the PHB that corresponds to the + config_addr + + + + + + PHB_Unit_ID_Low + + + + Represents the least-significant 32-bits of the Unit ID + of the PHB that corresponds to the + config_addr + + + + + Out + + + + Status + + + + 990x: Extended delay where x is a number 0-5 (see + Software Implementation note below) + 0: Success + -3: Parameter Error + + + + +
+ + Software Implementation Note: When the 990x + Status is returned, it is suggested that software + delay for 10 raised to the x milliseconds (where x is the last digit of + the 990x return code), before calling + ibm,configure-pe again. However, software may issue + the + ibm,configure-pe call again either earlier or later + than this. + + Firmware Implementation Note: + + + + + This call needs to limit the long busy to 9900-9902 with at most + a total of 1/5 second before the + ibm,configure-pe succeeds. Any longer delays may + cause subsequent hardware or application failures. + + + + For hardware errors, return a + Status of 0 (Success). Hardware errors are + subsequently discovered by further accesses to the PE and additional EEH + events. + + + + + + + R1--2. + + The caller of + ibm,configure-pe must provide the PE configuration + address, otherwise the RTAS call returns a -3, “Parameter + Error”. + + + + + R1--3. + + If the specified + PE has been configured after the last platform or OS initiated reset to + the specified PE with + ibm,configure-connector, + ibm,configure-bridge, or + ibm,configure-pe, then the call must return with a + Status of 0 (Success) without doing any bridge or + switch configuration, otherwise the call must set up the configuration + spaces of all the PCI to PCI bridges, PCI Express bridges, PCI Express + switches, and endpoint functions within the PE, the way they were + delivered at boot time except with all sticky error bits left intact, any + changes made by calls to ibm,change-msi retained, and must do so with a + single sequence of calls to + ibm,configure-pe. + + Software Implementation Notes: + + + + + The configuration of endpoint functions (the “and endpoint + functions” part) in Requirement + was added to the architecture + after the firmware without that functionality in the + ibm,configure-pe RTAS call was shipping. Therefore, + any device driver that might run legacy implementations needs to be + prepared to restore all endpoint function config spaces, since the + ibm,configure-pe RTAS call might not. + + + + The ibm,configure-pe RTAS call does not restore + non-interrupts configuration space changes that were made after boot + (that is, under direction of the device driver or OS). Therefore, use of + the + ibm,configure-pe RTAS call does not absolve the + device driver or OS from the restoration of non-interrupts the PCI + configuration space for changes that were made to the configuration space + after boot (see Requirement + ). + + + + + + + R1--4. + + The ibm,configure-pe call must only return a + Status of 990x if one of the following conditions is + true: + + + + The operation was not started. + + + + Firmware is able to restart the same call for this PE even when + other intervening calls to + ibm,configure-pe have occurred (That is, OSs are not + required to serialize calls to + ibm,configure-pe). + + + + + + + R1--5. + + Software must + complete all MMIO operations to the IOAs within a PE prior to calling the + ibm,configure-pe RTAS call for a PE and must not + issue new MMIO operations to the IOAs within the specified PE until after + the RTAS call is complete. + + + + + R1--6. + + On return from the + ibm,configure-pe RTAS call, the platform must have + the PE in the same EEH state (as defined by + ) as when the call was made, + except that if an error occurs in the course of probing the PCI fabric + that requires a reset of the PE by the platform, then discontinue + probing, return a + Status of 0 or 1 (as appropriate), and return the PE + in the PE state of 2. + + + + + + Software and Platform Implementation Note: + + + + + Given Requirements + and + , it is permissible for the + platform to temporarily transition the PE from a PE state of 2 to PE + state of 4, if the call is made with a PE state of 2 but the hardware + requires a PE state of 4 to get access to the PCI fabric. It is also + permissible for the platform to go through several of these state changes + during the execution of the call if there are errors that occur during + the course of probing the PCI fabric that put the PE back into the PE + state of 2. + + + + In Requirement + if an EEH event occurs as a + result of probing that fabric that results in a reset of the PE, the + returned PE state of 2 does not necessarily need to be checked for by the + software on return from the call. The case where this occurs is expected + to be rare, and probably signals a non-transient error. In this case the + software can continue on with the recovery phase of the EEH processing, + and will eventually hit the same event on further processing. + + + +
+ +
+ +
+ Error Injection Option + + The Error Injection option (ERRINJCT) allows testing software to + check out the OS’s error paths. This architecture defines the + following abstract error categories: + Fatal: Platform Architectural state has been corrupted to an + unknown extent. Further valid processing is not possible. + Recovered Random Event: The Central Electronics Complex (CEC) + experienced an anomaly. However, platform architectural state has been + preserved/restored. The OS should log the event and continue + processing. + Recovered Special Event: The CEC has experienced a statistically + significant anomaly. While platform architectural state has been + preserved/restored, the OS should log the event and discontinue the use + of this processor as soon as possible to avoid a fatal situation. + Corrupted Page: The System Memory page (Up to 4 KB) contains + uncorrectable errors. The OS should log the event and avoid accessing + this page in the future. The OS recovery is possible given that it can + either recover the page from backing storage or isolate the error from + unaffected processes. + Corrupted SLB: The processor’s Segment Look-aside Buffer is + corrupted. The OS should log the event and can recover if it can + repopulate the SLB from internal tables. + Translator Failure: The processor’s virtual to real + translation hardware has failed. The processor’s architectural + state has been preserved in System Memory. The OS may be able to continue + the failed processor’s program and log the event on an alternate + processor in the future. + IOA Bus Error An error has occurred on the I/O bus on which an I/O + Adapter (IOA) is attached. IOA or Device driver recovery from the error + is possible if the error is such that it is reported to the IOA. Device + driver recovery of the IOA’s operations is possible when the error + is not reported to the IOA, if the EEH option is implemented and + enabled. + The ERRINJCT option RTAS call performs a platform dependent + accurate simulation of the abstract error requested. In some cases, the + platform hardware actually injects an error into the hardware. In others + cases, the platform may simply report the anomaly without generating an + error. Additionally, the ERRINJCT option provides access to platform + specific error injection logic for the benefit of platform aware test + software. + + + + R1--1. + + For the ERRINJCT option: RTAS must implement the + ibm,open-errinjct call + using the argument buffer defined by + . + + + Argument Call Buffer + <emphasis>ibm,open-errinjct</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,open-errinjct + + + + + + Number Inputs + + + + 0 + + + + + + Number Outputs + + + + 2 + + + + + Out + + + + Open Token + + + + If + Status is 0, then use this Open Token for + corresponding + ibm,errinjct and + ibm,close-errinjct calls + + + + + + Status + + + + 990x: Extended delay, where x is a number 0-5 (see + text) + 0: Success + -1: Hardware Error + -2: Busy, try again later + -4: Already open + -5: PCI Error Injection is not enabled (not + available) + + + + +
+ When the 990x + Status is returned, it is suggested that software + delay for 10 raised to the x milliseconds (where x is the last digit of + the 990x return code), before calling with the same parameters. However, + software may issue the call again either earlier or later than + this. + + Architecture Note: The output buffer is intentionally + reversed from what it should be, according to Requirement + (that is, + Status not first output), due to code that was + implemented and shipped as defined, above. + + + + + R1--2. + + For the ERRINJCT option: On successful completion of + the + ibm,open-errinjct call, Firmware must return an Open + Token which uniquely identifies the caller on following + ibm,close-errinjct and + ibm,errinjct calls (Firmware may also need to keep + around other information about the caller that uniquely identifies the + caller when correlated with the Open Token) and must allocate the + ERRINJCT facilities to this caller until this same user calls + ibm,close-errinjct. + + + + + R1--3. + + For the ERRINJCT option: If the ERRINJCT facility has + been previously opened, a call to + ibm,open-errinjct call, must return a -4. + + + + + R1--4. + + For the ERRINJCT option: RTAS must implement the + ibm,close-errinjct call + using the argument buffer defined by + . + + + Argument Call Buffer + <emphasis>ibm,close-errinjct</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,close-errinjct + + + + + + Number Inputs + + + + 1 + + + + + + Number Outputs + + + + 1 + + + + + + Open Token + + + + Open Token that was returned on the corresponding + ibm,open-errinjct calls + + + + + Out + + + + Status + + + + 990x: Extended delay where x is a number 0-5 (see + text) + 0: Success + -1: Hardware Error + -2: Busy, try again later + -4: Close Error (User is not the one that opened the + ERRINJCT facility or facility not open) + + + + +
+ When the 990x + Status is returned, it is suggested that software + delay for 10 raised to the x milliseconds (where x is the last digit of + the 990x return code), before calling with the same parameters. However, + software may issue the call again either earlier or later than + this. + + + + + R1--5. + + For the ERRINJCT option: If the ERRINJCT facility is + not open or was not previously allocated to the user via an + ibm,open-errinjct call (that is, the Open Token along + with any other pertinent data does not correspond with the user that + opened the facility via the + ibm,open-errinjct call), then a call to + ibm,close-errinjct call, must return a -4 and the + facility must remain open for use by the user that originally opened the + facility. + + + + + R1--6. + + For the ERRINJCT option: RTAS must implement the + ibm,errinjct call + using the argument buffer defined by + . + + + Argument Call Buffer + <emphasis>ibm,errinjct</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,errinjct + + + + + + Number Inputs + + + + 3 + + + + + + Number Outputs + + + + 1 + + + + + + Errinjct Token + + + + Token for the specific error injection class see + Requirement + + + + + + + Open Token + + + + The Open Token that was returned on the corresponding + ibm,open-errinjct call + + + + + + Working Buffer + + + + Real address of a 1 KB buffer on a 1 KB boundary + + + + + Out + + + + Status + + + + 990x: Extended delay where x is a number 0-5 + 0: Success + -1: Hardware Error + -2: Busy, try again later + -3 Argument Error (Optional) + -4: Call Error (User is not the one that opened the + ERRINJCT facility or facility not open) + + + + +
+ When the 990x + Status is returned, it is suggested that software + delay for 10 raised to the x milliseconds (where x is the last digit of + the 990x return code), before calling with the same parameters. However, + software may issue the call again either earlier or later than + this. + + + + + R1--7. + + For the ERRINJCT option: If the ERRINJCT facility is + not open or was not previously allocated to the user via an + ibm,open-errinjct call (that is, the Open Token along + with any other pertinent data does not correspond with the user that + opened the facility via the + ibm,open-errinjct call), then a call to + ibm,errinjct call, must return a -4 and the facility + must remain open for use by the user that originally opened the + facility. + + + + + R1--8. + + For the ERRINJCT option: + The platform must include the + “ibm,errinjct-tokens” property as defined + below in the + /rtas node (see + ) of the OF device tree with a + specification for each implemented error injection class. + + + + + R1--9. + + For the ERRINJCT option: The errinjct-token-names + must be taken from the list provided in + . + + + Errinjct-token-names + + + + + + + + Errinjct-token-name + + + + + Errinjct function + + + + + + + + fatal + + + Simulate a platform fatal error. + + + + + recovered-random-event + + + Simulate a recovered random event + + + + + recovered-special-event + + + Simulate a recovered special (statistically significant) + event + + + + + corrupted-page + + + Corrupt the specified location (and potentially + surrounding locations up to the containing page) + + + + + corrupted-slb + + + Corrupt the SLB entry associated with a specific + effective address. + + + + + translator-failure + + + Simulate a translator failure. + + + + + ioa-bus-error + + + Simulate an error on an IOA bus - 32 bit address + specification only. + + + + + ioa-bus-error-64 + + + Simulate an error on an IOA bus - 64 bit address + specification. + + + + + platform-specific + + + Request the firmware perform a platform specific error + injection. + + + + + corrupted-dcache-start + + + Start causing a L1 data cache error + + + + + corrupted-dcache-end + + + Stop causing a L1 data cache error + + + + + corrupted-icache-start + + + Start causing an instruction cache error + + + + + corrupted-icache-end + + + Stop causing an instruction cache error + + + + + corrupted-tlb-start + + + Start corrupting TLB + + + + + corrupted-tlb-end + + + Stop corrupting TLB + + + + + upstream-IO-error + + + Inject I/O error above the IOA + + + + +
+ + + + + R1--10. + + For the ERRINJCT option: For the errinjct-tokens + implemented RTAS must use the work buffer format specified in + . + + + Errinjct Work Buffer Formats + + + + + + + + Errinjct-token-name + + + + + Errinjct work buffer format + + + + + + + + fatal + + + Undefined + + + + + recovered-random-event + + + Undefined + + + + + recovered-special-event + + + “1” for a non-persistent cpu recoverable + error + “2” for a persistent CPU recoverable + error + + + + + corrupted-page + + + The first cell contains the upper 32 bits of the real + address to corrupt. The second cell contains the lower 32 bits + of the real address to corrupt. + + + + + corrupted-slb + + + The first cell contains the effective address associated + with the SLB entry to corrupt + + + + + translator-failure + + + Undefined + + + + + ioa-bus-error + + + The first word contains I/O bus address, word aligned, at + which to inject the error. The second word is a mask used to + mask off up to 24 of the least significant bits of the address + which are not to be used in the comparison of address for error + injection (a 0 in a bit position masks off the bit, a 1 in the + bit position enables the bit to be used in the compare). The + third word is the config_addr on the bus which is to receive + the injected error. The fourth word is the + PHB_Unit_ID_Hi of the PHB that corresponds + to the + config_addr. The fifth word is the + PHB_Unit_ID_Low of the PHB that corresponds + to the + config_addr. The sixth word defines the + specifics of when and what to inject, as follows: + + See + for values 0 through + 19. + 20: (Optional) Disable PCI error injection for the + specified bus + 21: Obtain current error inject values. When RTAS returns + SUCCESS in the + Status field the work buffer field values + are populated with the current error injected. + + + + + ioa-bus-error-64 + + + The first and second words contain the I/O bus address, + double word aligned, at which to inject the error. The third + and fourth words are a mask used to mask off up to 64 of the + least significant bits of the address which are not to be used + in the comparison of address for error injection (a 0 in a bit + position masks off the bit, a 1 in the bit position enables the + bit to be used in the compare). The fifth word is the + config_addr of an IOA on the bus which is to receive the + injected error. The sixth word is the + PHB_Unit_ID_Hi of the PHB that corresponds + to the + config_addr. The seventh word is the + PHB_Unit_ID_Low of the PHB that corresponds + to the + config_addr. The eighth word defines the + specifics of when and what to inject, as follows: + + See + for values 0 through + 19. + 20: (Optional) Disable PCI error injection for the + specified bus + 21: Obtain current error inject values. When RTAS returns + SUCCESS in the + Status field the work buffer field values + are populated with the current error injected. + + + + + + platform-specific + + + See platform firmware documentation (RTAS component + specifications) for working buffer format for any particular + platform. + + + + + corrupted-dcache-start + corrupted-dcache-end + + + The first cell defines the specific action to + take: + 0: Parity error + 1: D-ERAT parity error + 2: tag parity error + The second cell defines the nature of the error: + 0: single + 1: solid + 2: hang + Supported injection modes are hardware specific and all + modes may not be supported on all hardware. The first supported + injection mode in the above list will be used if an unsupported + mode is specified (that is, first single, then solid, then + hang-pulse). If none of the above modes are available, then the + injection option most similar to single in functionality will + be used. + + + + + + + + + + + + + + + + + + + + corrupted-icache-start + corrupted-icache-end + + + The first cell defines the specific action to + take: + 0: parity error + 1: I-ERAT parity error + 2: cache directory 0 parity error + 3: cache directory 1 parity error + The second cell defines the nature of the error: + 0: single + 1: solid + 2: hang + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + corrupted-tlb-start + corrupted-tlb-end + + + The first cell defines the nature of the error: + 0: single + 1: solid + 2: hang + Supported injection modes are hardware specific and all + modes may not be supported on all hardware. The first supported + injection mode in the above list will be used if an unsupported + mode is specified (that is, first single, then solid, then + hang-pulse). If none of the above modes are available, then the + injection option most similar to single in functionality will + be used. + + + + +
+ + Programming Note: Options having a + “-start” and corresponding “-end” must be called + in pairs on the same processor. The corresponding “-end” + option should be called after the injected error has been noticed and + processed by the caller. On the same processor, other error inject + options should not be called between a “-start” and + “-end” sequence. However, it is possible to inject the same + type of error multiple times by calling “-start” on that CPU + as long as the “nature of error” is “single”. The + buffer contents should be the same for a “-start” and + corresponding “-end”. While not recommended -end can be + replaced with a call to + ibm,close-errinjct, but improper cleanup the machine + may result, with the machine left in an unknown state. + + + + + R1--11. + + For the ERRINJCT option: If the platform + notifies the OS of a specific CEC error using the machine check interrupt in + response to an + ibm,errinjct RTAS call, the platform must do so only + when the processor’s MSRRI bit is active, unless said error is fatal or + involves accessing a storage location that has itself been corrupted or + is accessed through a corrupted SLB entry. + + + + + R1--12. + + For the ERRINJCT option with the LPAR + option: Hypervisor RTAS must allow a partition to only corrupt + its own memory pages. + + + + + R1--13. + + For the ERRINJCT option with the LPAR + option: Hypervisor RTAS must allow a partition to inject IOA + bus errors only if all of the following are true: + + + + The IOA bus is not shared with other partitions. + + + + The EEH option is implemented and enabled for the bus on which + the error injection is requested. + + + + + + + R1--14. + + For the ERRINJCT option with the LPAR option: The + platform must allow at most one partition to issue platform-specific + errinjct calls. + + + + + R1--15. + + For the SPLPAR option: The platform must either + implement actual hardware error injection with these interfaces, or must + fabricate appropriate partition behavior (machine check, error logs, + etc.) as if the hardware error had happened. + + + + + R1--16. + + For the Multi-threading Processor + option: All threads + on the processor on which the error is injected must be prepared to + handle the error. + + + + + R1--17. + + For the Error Injection option: The software using + the + ibm,errinjct call must be prepared to receive a -3 + for non-implemented errinjct work buffer formats. + + + + + R1--18. + + For the + ioa-bus-error + and + ioa-bus-error-64 + functions of the ERRINJCT option: For each + ibm,errinjct RTAS call invocation, the platform must + inject the error specified in the + working buffer at most once. + + + Semantics for + <emphasis>ioa-bus-error</emphasis> + <emphasis>ioa-bus-error</emphasis> Sixth Word and + <emphasis>ioa-bus-error-64</emphasis> Eighth Word Values 0-19 + + + + + + + + + + + Operation + + + + + Address Space + + + + + Cell Value + + + + + Conventional PCIPCI-X Mode 1PCI-X Mode + 2 + + + + + PCI Express + + + + + + + + + Load + + + + PCI Memory + + + 0 + + + Inject an Address Parity Error + + + Inject a TLP ECRC Error + + For PHB implementations that do not allow injection of + a TLP ECRC error into the request, or for the case where the + injection would be in violation of Requirement + due to the hardware + configuration, the platform should emulate the error by + setting the appropriate error state in the PHB when EEH is + enabled. + + + + + + 1 + + + Inject a Data Parity Error + + + + + PCI I/O + + + 2 + + + Inject an Address Parity Error + + + + + 3 + + + Inject a Data Parity Error + + + + + PCI Configuration + + + 4 + + + Inject an Address Parity Error + + + + + 5 + + + Inject a Data Parity Error + + + + + + Store + + + + PCI Memory + + + 6 + + + Inject an Address Parity Error + + + Inject a TLP ECRC Error (optional) + + + + + 7 + + + Inject a Data Parity Error + + + + + PCI I/O + + + 8 + + + Inject an Address Parity Error + + + + + 9 + + + Inject a Data Parity Error + + + + + PCI Configuration + + + 10 + + + Inject an Address Parity Error + + + + + 11 + + + Inject a Data Parity Error + + + + + DMA read + + + PCI Memory + + + 12 + + + Inject an Address Parity Error + + + Inject a TLP ECRC Error + + + + + 13 + + + Inject a Data Parity Error + + + + + 14 + + + Inject a Master Abort (no response to IOA) Error + + + -- + + + + + 15 + + + Inject a Target Abort + + + Inject a Completer Abort or Unsupported Request + + Inject the error that is injected on a TCE Page + Fault. + + + + + + DMA write + + + PCI Memory + + + 16 + + + Inject an Address Parity Error + + + Inject a TLP ECRC Error + + + + + 17 + + + Inject a Data Parity Error + + + + + 18 + + + Inject a Master Abort (no response to IOA) Error + + + -- + + + + + 19 + + + Inject a Target Abort + + + Not Applicable + + + + +
+ + + + + + + Platform Implementation Notes: + + + + + Platforms that implement LPAR normally do not allow any partition + to be configured to perform platform-specific errinjct calls since they + are capable of crashing the entire complex. However, the should provide + special hidden overrides for laboratory testing purposes. + + + + + Software and Firmware Implementation Notes: + + + + + When a call to + ibm,errinjct results in an error injected into a + processor, then the error is injected on the same processor as the one + that called the + ibm,errinjct RTAS call, not the processor that called + the + ibm,open-errinjct. The OS could call + ibm,open-errinjct, + ibm,errinjct, and + ibm,close-errinjct from three different + processors. + + + + For usability reasons, the + ibm,close-errinjct RTAS call should do a reasonable + amount of cleanup; turning off error injection where it can. However, + since the ERRINJCT option is intended for internal use (that is, not + intended to be productized) and since software is allowed to basically + set unlimited error injections between the calls to + ibm,open-errinjct and + ibm,close-errinjct, the firmware may vary by + implementation as to what is cleaned up and what is not. An example of + something that might be very difficult to clean up is injection of memory + errors. Something that might be easier is to turn off the error injection + in all bridges to which the caller has access. Users of the ERRINJCT + option should consult the implementation documentation for a particular + platform to learn about the level of cleanup that is done in the + ibm,close-errinjct call for that implementation. In + the severe case, a reboot may even be necessary after the + ibm,close-errinjct in order to clear the error. In + other cases it may be possible for the caller to partially disable an + error that it has set by setting a benign error (for example, in the PCI + error injection case, by setting the error injection for a bus that was + previously set to inject an error to an address that will never occur to + that IOA). + + + + Test developers are encouraged not to extensively use the + platform-specific option to this function. In general, platform-specific + implementation options are not carried forward to new platforms. + + + +
+ +
+ Firmware Assisted Non-Maskable Interrupts Option + (FWNMI) + + The FWNMI option provides firmware support for System Reset + interrupts and platform dependent error recovery for recoverable machine + checks. The firmware gets control on a non-maskable interrupt (NMI), + analyses the condition, and, if the processor was not running inside the + hypervisor, reports its findings to the OS. The OS registers system reset + and machine check handlers by issuing either the + ibm,nmi- register or + ibm,nmi- register-2 RTAS call. In addition, with + these calls the OS permanently relinquishes to firmware the Machine State + Register’s Machine Check Enable bit, the two hundred fifty six + (256) bytes of the System Reset Interrupt vector starting at real + location 0x100, the two hundred fifty six (256) bytes of the Machine + Check Interrupt vector starting at real location 0x200, as well as the + storage page starting at real location 0x7000. The RTAS firmware records + the entry points of the OS notification routines to call to report the + results of the firmware’s analysis and any attempted recovery + should the hardware signal a machine check or system reset interrupt. The + results of an error analysis are reported via a standard error log + structure as defined in + . The storage containing the + error log structure is subsequently released back to firmware use by the + OS after it has completed its event handling by the issuance, from the + interrupted processor, of the + ibm,nmi-interlock RTAS call. Multiple processors of + the same OS image may experience fatal events at, or about, the same + time. The first processor to enter the machine check handling firmware + reports the fatal error. Subsequent processors serialize waiting for the + first processor to issue the + ibm,nmi-interlock call. These subsequent processors + report “fatal error previously reported”. If, after the + firmware makes a Machine Check call back, and before the OS issues the + ibm,nmi-interlock call, the same processor that is + currently holding the storage containing the error log structure receives + another Machine Check NMI, the firmware has no choice but to declare the + condition fatal, log the result and execute the partition’s reboot + policy. + When the OS gets control after a machine check, at its registered + machine check notification routine, all architected processor registers + have been restored to the values they contained when the firmware was + notified of the interrupt, except for register R3 which contains a real + address that points to a 16 byte structure. The first 8 bytes of this + area contains the original contents of R3 and the second 8 bytes contains + the fixed portion of the standard error log structure. If firmware is + able to immediately make a repair determination, the fixed portion + indicates that an additional variable part is present and follows the + fixed part per the standard error log structure. For some other errors, + the determination of the repair action is delayed, and the firmware + reports these determinations asynchronously to handling the machine + check. The repair action log is queued in the NVRAM and is reported + either in a subsequent + event-scan if the OS image remains operational, or on + a subsequent boot. In no case, does the OS call + check-exception in its machine check notification + routine. + The difference between + ibm,nmi- register and + ibm,nmi- register-2 is that + ibm,nmi- register allocates the error reporting + structure in RTAS space while + ibm,nmi- register-2 places the error reporting + structure in real page 7. New OS designs should use + ibm,nmi- register since support for + ibm,nmi- register-2 will be terminated at some future + date. + As with all first level interrupt service routines, the SPRG-2 + register is used to save the state of one general purpose register while + the processor computes the location of its state save area. + + Implementation Note: An acceptable non-LPAR firmware + implementation for the NMI check handlers saves one register in an + SPRG-2. Then, using the processor number register, determines an offset + into a page 7 table of addresses to the start of a per processor RTAS + save area (only need a single register saved per processor), and acquires + a lock located in page 7 to serialize the use of the RTAS state save area + among potentially competing processors. The MSRME + bit then prevents single processor Machine Check + stacking in the interval between the Machine Check call back and the + ibm,nmi-interlock call. LPAR implementations should + minimize potential effects to innocent partitions due to Machine Check + Interrupts affecting other partitions. + If the NMI was taken inside the hypervisor, then, if the firmware + determines that the condition is recoverable, the hypervisor recovery + routine is invoked. If the condition is not recoverable, hypervisor clean + up routines establish a safe state and mark the hypervisor return routine + to invoke the proper OS registered NMI routine rather than doing the + standard hypervisor return. + + + + R1--1. + + All platforms must implement the FWNMI + option. + + + + + R1--2. + + For the FWNMI option: + The platform must include the + “ibm,nmi-register” + RTAS function property name in the OF + /rtas node. + + + + + R1--3. + + For the FWNMI option: + The platform must include the + “ibm,nmi-register-2” + RTAS function property name in the OF + /rtas node if the platform requires support from + interim OS versions. + + + + + R1--4. + + For the FWNMI option: RTAS must implement the + ibm,nmi-register and/or + ibm,nmi-register-2, calls as appropriate per + Requirements + and + using the argument buffer + defined by + . + + + Argument Call Buffer + <emphasis>ibm,nmi-register or ibm,nmi-register-2</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,nmi-register or nmi-register-2 + + + + + + Number of Inputs + + + + 2 + + + + + + Number of Outputs + + + + 1 + + + + + + System Reset Notification Routine + + + + Real/Logical address of OS routine to call on a System + Reset (in the first 32 MB of memory). + + + + + + Machine Check a + + + Notification Routine + + + + Real/Logical address of OS routine to call on a Machine + Check (in the first 32 MB of memory). + + + + + Out + + + + Status + + + + 0: Success + -1: Hardware Error + -3: Parameter Error + + + + +
+ + + + + R1--5. + + For the FWNMI option: Once the + OS has registered for + NMI notification, it must not change the contents of the two hundred + fifty six (256) bytes of the NMI interrupt vectors at real locations + 0x100 or 0x200 or the memory page starting at real location + 0x7000. + + + + + R1--6. + + For the FWNMI option: + The Real/Logical + address of the registered OS Machine Check and System Reset routines must + be in the first 32 MB of the OS’s memory address space. + + Software Implementation Note: Requirement + ensures that the registered OS + Machine Check and System Reset routines are within the code’s + RMA. + + + + + R1--7. + + For the FWNMI option: If the OS registered with + ibm,nmi-register, firmware must not store the state + of the processor at the time of interrupt in interrupt vectors at + locations 0x100 or 0x200 or the memory page starting at real location + 0x7000. Firmware may use RTAS space to store such state data. + + + + + R1--8. + + For the FWNMI option: Once the OS has registered for + NMI notification, the platform firmware must intercept all System Reset + Interrupts on all of the OS’s processors. + + + + + R1--9. + + For the FWNMI option: The + platform firmware, for + those intercepted System Reset interrupts which platform policy dictate + are to be forwarded to the OS, must invoke the OS registered System Reset + Interrupt notification point with translate off and all other architected + processor registers restored to their state at the time of the System + Reset. + + + + + R1--10. + + For the FWNMI option: Once the OS has registered for + NMI notification, the platform firmware must intercept all Machine Check + Interrupts on all of the OS’s processors. + + + + + R1--11. + + or the FWNMI option: The platform must provide a + mechanism for the firmware to signal a non-maskable interrupt to each + processor in a partition. + + + + + R1--12. + + For the FWNMI option: The platform firmware must + analyze all intercepted Machine Check Interrupts, determine if the OS may + safely continue using the platform, attempt to recover any corrupted + architectural state, and report the results of the recovery attempt to + the OS. + + + + + R1--13. + + For the FWNMI option: If the platform firmware, on + analyzing an intercepted Machine Check Interrupt, determines that the OS + may safely continue using the platform, it must invoke the OS registered + Machine Check Interrupt notification point with translate off but all + other architected processor registers restored to their state at the time + of the Machine Check except that General Purpose Register (GPR) R3 + contains the real address of a 16 byte memory buffer containing the + original contents of GPR R3 in the first 8 bytes and the RTAS Error Log + (fixed part) (per + ) in the second 8 bytes. + + + + + R1--14. + + For the FWNMI option: The maximum time for the + platform’s processing of a non-fatal machine check interrupt must + be on the order of that taken by the + check-exception critical call. + + + + + R1--15. + + For the FWNMI option: Once the firmware has reported + a “fatal” machine check event to an OS image it must only + report “fatal error previously reported” (see + ) in response to machine checks + on any processor belonging to that image. + + + + + R1--16. + + For the FWNMI option: If the platform firmware, on + analyzing an intercepted Machine Check Interrupt, determines that the OS + may not safely continue using the processor (for example a check stop + will certainly result), it must select one of the implementation options + given in + . + + + Unsafe Processor Recovery Options + + + + + + + + Option Number + + + + + Implementation Option for handling an + unsafe processor. + + + + + + + + 1 + + + Invoke the registered Machine Check Interrupt + notification point on a spare processor which platform firmware + substitutes for the offending processor. + + Note: Firmware must adjust all interrupt + XIVT entries and APM registers, etc., so that the OS need not + be aware of the processor substitution. The VPD of the new and + old processors are different, the dynamic VPD collection RTAS + call can be used to determine the new values. Since the results + of this substitution are indicated as a non-fatal error to the + OS, the substitution may take no more than 10 times the length + of time of a critical check exception process. The firmware + makes a best effort to load the decrementer with a value that + represents the value in the failed processor at + the time of the machine check minus a value that + represents the time taken by the substitution process. + + + + + 2 + + + Mark the processor unsafe, do not return to the OS on + that processor and notify the OS to at the next event scan time + with a fatal return message. + Note: This action + may cause the OS to “hang” + due to locks held by the failing processor etc. that may cause + a surveillance time out. The NVRAM firmware error log retains a + trail of this condition for reading and logging at the + subsequent OS boot. However, in those cases where a hang does + not happen, the OS can select some other processor to pick up + the thread of execution. + + + + +
+ + + + + R1--17. + + For the FWNMI option: RTAS must implement the + ibm,nmi-interlock call using the Argument buffer + defined in + which causes the release of the + machine check work and reporting area in page 7. + + + Argument Call Buffer + <emphasis>ibm,nmi-interlock</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,nmi-interlock + + + + + + Number of Inputs + + + + 0 + + + + + + Number of Outputs + + + + 1 + + + + + Out + + + + Status + + + + 0: Success + -1: Hardware Error + + + + +
+ + + + + R1--18. + + For the FWNMI option: The + + ibm,nmi-interlock RTAS call must not require + serialization with respect to any other RTAS or hypervisor calls. + + + + + R1--19. + + For the FWNMI option: The + processor receiving the nmi signal must, after it + has processed the buffer pointed to by its R3 register, call the + ibm,nmi-interlock RTAS call. + + + + +
+ +
+ Memory Statistics + + Depending upon the platform configuration, various portions of + installed platform memory are in one of several states. Some memory may + be mapped out of the address space due to an error in one or more + locations. Other memory is used by the platform firmware. What is left is + allocated to one or more logical partitions or held in reserve. The usage + of memory is a first order platform management parameter, and is needed + by platform managers. However, it may also become a covert channel + between logical partitions. Therefore, the memory usage information that + is surfaced to an OS image by firmware is restricted to total platform + memory installed, plus three sub-divisions which total to the total + memory installed. These three sub-divisions are the total memory the + platform mapped out due to hardware failure, total memory reserved for + platform firmware and other partitions, and the memory allocated to the + calling OS image. LPAR machines can provide a more detailed memory usage + report via their Hardware Management Console. The total memory allocated + to the calling OS image is obtained through the device tree (potentially + modified by post boot dynamic reconfiguration). +
+ +
+ System Parameters Option + + The system parameters which are defined are shown in + . + + + Defined Parameters + + + + + + + + + + + Parameter token + + + + + Parameter + + + + + Description + + + + + Values + + + + + Notes + + + + + + + + 0 + + + HMC 0 + + +   + + +   + + +   + + + + + 1 + + + HMC 1 + + +   + + +   + + +   + + + + + 2 thru 15 + + + HMC 2 thru 15 + + +   + + +   + + +   + + + + + 16 + + + Reserved + + +   + + +   + + +   + + + + + 17 + + + Reserved + + +   + + +   + + +   + + + + + + 18 + + + Processor CoD Capacity Card Info + + + + + + + +   + + + 1 + + + + + 19 + + + Memory CoD Capacity Card Info + + + + + + + +   + + + 1 + + + + + 20 + + + SPLPAR Characteristics + + + Opaque ASCII NULL terminated string + + +   + + + 1, 2 + + + + + 21 + + + partition_auto_restart + + + + + + + +   + + +   + + + + + 22 + + + platform_auto_power_restart + + + + + + + +   + + +   + + + + + 23 + + + sp-remote-pon + + + Remote Power On + (see + ) + + + One byte decimal + 0 (for off) + 1 (for on) + Default 0 + + +   + + + + + 24 + + + sp-rb4-pon + + + Number of rings until power on + (see + ) + + + One byte decimal + + +   + + + + + 25 + + + sp-snoop-str + + + Snoop sequence string + (see + ) + + +   + + +   + + + + + 26 + + + sp-serial-snoop + + + Serial snoop enable/disable + (see + ) + + + 0 (for off) + 1 (for on) + Default 0 + + +   + + + + + 27 + + + sp-sen + + + Surveillance enable/disable + (see + ) + + + 0 (for off) + 1 (for 0n) + Default 0 + + +   + + + + + 28 + + + sp-sti + + + Surveillance time interval in minutes + (see + ) + + + 1-255 + Default 5 + + +   + + + + + 29 + + + sp-sdel + + + Surveillance delay in minutes + (see + ) + + + 1-120 + Default 10 + + +   + + + + + 30 + + + sp-call-home + + + + + + + +   + + +   + + + + + 31 + + + sp-current-flash-image + + + + + + + + 0 (for perm) + 1 (for temp) + + +   + + + + + 32 + + + platform-dump-max-size + + + + + + + + 64-bit integer + + + The value consists of a 32-bit high value followed by a + 32-bit low value. The resulting 64-bit value is + unsigned. + + + + + 33 + + + epow3-quiesce-time + + + + + + + + 0-65535 seconds + Default 0 + + +   + + + + + 34 + + + memory-preservation-boot-time + + + + + + + + 0-65535 seconds + Default 0 + + +   + + + + + 35 + + + SCSI Initiator Identifier + + + + + + + +   + + +   + + + + + 36 + + + AIX support + + +   + + +   + + +   + + + + + 37 + + + Enhanced Processor CoD Capacity information + + + + + + + +   + + + 1 + + + + + 38 + + + Enhanced Memory CoD Capacity information + + +   + + + 1 + + + + + 39 + + + CoD options + + + See + . + + +   + + + 1 + + + + + 40 + + + Platform Error Classification + + + See + . + + +   + + +   + + + + + 41 + + + Firmware Boot Options + + + See + . + + +   + + +   + + + + + 42 + + + platform-processor-diagnostics-run-mode + + + + + + + + One byte decimal + 0=disabled + 1=staggered + 2=immediate + 3=periodic + + +   + + + + + 43 + + + Processor Module Information + + + See + . + + +   + + + 1 + + + + + 44 + + + Cooperative Memory Over-commitment Definitions + + + Opaque ASCII NULL terminated string + + +   + + + 1, 3 + + + + + 45 + + + Cede Latency Settings Information + + + + + + + +   + + +   + + + + + 46 + + + Target Active Memory Compression Factor + + + + + + + + Field length: 2 bytes + Format: binary + Range: 100 -- 1000 + + +   + + + + + 47 + + + Performance boost modes vector + + + See + . + + + From + ibm,get-system-parameter the field length + is 96 bytes consisting of 3 32 byte bit vectors. To + ibm,set-system-parameter the field is a + single 32 byte bit vector + + +   + + + + + 48 + + + UUID + + + 16 Byte String + + + + + + + +   + + + + + >48 + + + Reserved + + +   + + +   + + +   + + + + +
+ + Notes: + + + + + These system parameters are defined for the + ibm,get-system-parameter RTAS call only. An attempt + to set them using the + ibm,set-system-parameter RTAS call results in a + return + Status of -9002 (Setting not + allowed/authorized). + + + + The format of the SPLPAR string is beyond the scope of this + architecture. See also, + . + + + + See . + Further parameters will be defined as required. + + + + + + + R1--1. + + All platforms must support the System + Parameters option. + + + + + R1--2. + + (Requirement Number Reserved For + Compatibility) + + + + + R1--3. + + For the System Parameters option: If the length of + the data for a parameter in + is less than what is specified + in the requirements for a parameter or if the data value in an + ibm,set-system-parameter RTAS call is other than what + is allowed by the requirements for the parameter, the platform must + return a -9999 indicating a parameter error. + + + + + R1--4. + + For the System Parameters option: + The default values + defined for parameters sp-sen, sp-sti and sp-sdel in the + must apply to the platform + prior to any + ibm,set-system-parameter RTAS call. + + + + + R1--5. + + For the System Parameters option: The + ibm,get-system-parameter RTAS call must implement the + argument call buffer defined by + . If the + ibm,set-system-parameter RTAS call is implemented, it + must use the argument call buffer defined by + . + + + + + R1--6. + + For the System Parameters option: If the platform + implements the + ibm,set-system-parameter RTAS call it must also + implement the + ibm,get-system-parameter RTAS call. + + + + + R1--7. + + For the System Parameters option: A system parameter, + which is not supported by the system, must return a + Status of -3 (System parameter not supported) from + the RTAS call. + + + + + R1--8. + + For the System Parameters option: A system parameter + for which access is not authorized, must return a + Status of -9002 (Not authorized) from the RTAS + call. + + + + + R1--9. + + For the System Parameters option: When a platform + implements a system parameter, it must meet the definition in + including applicable + descriptions and notes. + + + + + R1--10. + + For the System Parameters option: An + ibm,get-system-parameter RTAS call with a buffer + length of zero (0) must return a + Status of + 0 (success) if the parameter is supported and + authorized, a + Status of -3 if not supported, or a + Status of-9002 if not authorized. + + + + + R1--11. + + For the System Parameters option: An + ibm,set-system-parameter RTAS call with a parameter + length of zero (0) must return a + Status of + 0 (success) if the parameter is supported and + authorized, a + Status of -3 if not supported, or a + Status of -9002 if not authorized. + + Programming Note: A partition may lose or gain + authority for an + ibm,get-system-parameter or + ibm,set-system-parameter call dynamically. For + instance, three consecutive calls with the same parameters could return + Status of success, not authorized, and + success. + + + + + R1--12. + + For the System Parameters option: The + platform must + enforce the length of system parameter strings as follows: input strings + to ibm,set-system-parameters not to exceed 1024 bytes in length else the + platform returns a Status of -9999 (parameter error) from the RTAS call; + output strings from ibm,get-system-parameters not to exceed 4000 + bytes. + + + + + R1--13. + + For the System Parameter option with the SPLPAR + option: The Platform must implement parameter token 20 as + defined in + for + ibm,get-system-parameter. + + Implementation Note: Of course the OS is allowed to + provide and specify a buffer that is larger than the maximum system + parameter length. + + + + +
+ <emphasis>ibm,get-system-parameter</emphasis> + + + Argument Call Buffer + <emphasis>ibm,get-system-parameter</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,get-system-parameter + + + + + + Number Inputs + + + + 3 + + + + + + Number Outputs + + + + 1 + + + + + + Parameter + + + + Token of system parameter to retrieve + + + + + + buffer + + + + Real address of data buffer + + + + + + length + + + + length of data buffer + + + + + Out + + + + Status + + + + 0: Success + -1: Hardware Error + -2: Busy, Try again later + -3: System parameter not supported + -9002: Not authorized + -9999: Parameter Error + 990x: Extended delay where x is a number 0-5 (see text + below) + + + + + + + + + +
+ The + ibm,get-system-parameter RTAS call fetches the data + for the selected parameter and places it at the address specified in the + buffer operand. The first two (2) bytes of the data in the buffer are the + length of the returned data, not counting these first two (2) bytes. The + length of string data includes the length of the NULL but excludes the + length field. If the buffer length is less than the returned data length, + the data is truncated at the end of the buffer. The maximum length of the + input parameter data string for + ibm,set-system-parameter is architecturally limited + to 1024 bytes of data and 2 bytes of length, totaling 1026 bytes. The + maximum length of the output parameter data string for + ibm,get-system-parameter is architecturally limited to 4000 bytes of data + and 2 bytes of length, totaling 4002 bytes. The only currently valid + parameters are as specified in + . + When the 990x + Status is returned, it is suggested that software + delay for 10 raised to the x milliseconds (where x is the last digit of + the 990x return code), before calling + ibm,get-system-parameter with the same parameter + index. However, software may issue the + ibm,get-system-parameter call again either earlier or + later than this. +
+ +
+ <emphasis>ibm,set-system-parameter</emphasis> + + + Argument Call Buffer + <emphasis>ibm,set-system-parameter</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,set-system-parameter + + + + + + Number Inputs + + + + 2 + + + + + + Number Outputs + + + + 1 + + + + + + Parameter + + + + Token number of the target system parameter + + + + + + buffer + + + + Real address of data buffer + + + + + Out + + + + Status + + + + 0: Success + -1: Hardware Error + -2: Busy, Try again later + -3: System parameter not supported + -9002: Setting not allowed/authorized + -9999: Parameter Error + 990x:Extended delay where x is a number 0-5 (see text + below) + + + + + + + + + +
+ The + ibm,set-system-parameter RTAS call fetches the data + from the address specified in the buffer operand and sets it into the + system parameter specified by the + Parameter operand. The first two (2) bytes of the + data in the buffer are the length of the data, not counting these first + two (2) bytes. The length of string data includes the length of the NULL + but excludes the length field. The only currently valid parameters are as + specified in + . + When the 990x + Status is returned, it is suggested that software + delay for 10 raised to the x milliseconds (where x is the last digit of + the 990x return code), before calling + ibm,set-system-parameter with the same parameter + index. However, software may issue the + ibm,set-system-parameter call again either earlier or + later than this. +
+ +
+ HMC Parameter + The full HMC parameter data string is returned when the + ibm,get-system-parameter RTAS call is issued. + HMC parameter contents are: + length - two byte binary length of data string associated with the + HMC. + System Parameter Data - string of semicolon delimited ASCII + data. + The + ibm,set-system-parameter is not required to support + the HMC parameter since the HMC parameter data is set only by the HMC + through an out-of-band path. The + ibm,get-system-parameter RTAS call is provided for + reading the parameter data. The RTAS call is available in both LPAR mode + and non-LPAR mode. + + + + R1--1. + + For the HMC Parameter: If the + ibm,set-system-parameter RTAS call is provided, the + use of the HMC parameters, 0-15, must always return not authorized + Status, -9002. + + + + + R1--2. + + For the HMC Parameter: The + format of each HMC system + parameter supported by this system must consist of a two byte binary + length field describing the full length of the parameter data, followed + by a series of variables where each variable is of the form + “keyword” followed by “=” followed by + “value” and terminated by “;”. The order of the + variables is undefined and the total number of variables is undefined. + The platform must provide the “HscIPAddr” keyword + + The acronym “HSC” was replaced by “HMC” + but this keyword was retained with “Hsc” so as to not + invalidate code already created using the keyword. + , and the “RMCKey” keyword. The data after the + equal sign (=) may or may not have content. The value of the + “HscIPAddr” keyword is the IP address of that HMC. The value + of the “RMCKey” keyword is either null or is the RMC key for + that system or partition. The value of a keyword is null if there is + nothing between the “=” and the “;”. The update + state of keyword values of an HMC system parameter are uncertain when the + HMC stops talking to the managed system. + + + + + R1--3. + + For the HMC Parameter: All + HMC system parameter data + must be printable ASCII characters, excluding the two byte binary length + field. + + + + + R1--4. + + For the HMC Parameter: The + lowest valued HMC system + parameter which returns a -3 + Status must have no higher valued HMC system + parameter which is supported. That is, a scan of HMC system parameters + from 0 until the first -3 + Status must indicate all supported HMC system + parameters. + + + + + R1--5. + + For the HMC Parameter: If + there is no HMC control of + this platform, the platform must return a null response, zero length + data, to requests for all supported HMC system parameters. + + Implementation Note: Since the system is not + necessarily to be HMC controlled, it is shipped with the HMC parameter + set to the zero (0) length. If the system is HMC controlled, the HMC + passes the parameter values to the system at boot time so that the + ibm,get-system-parameters RTAS call indicates HMC + control. If there is deconfigured the HMC can write the zero (0) length + data to the system. If that is not done, the system can write the + parameter to zero length on a hard reset and the HMC, if present, then + initializes the data. + + + + + R1--6. + + For the HMC Parameter: The + platform must truncate the + HMC system parameter data at the buffer length if the buffer length is + less than the data length plus 2. + + + + +
+ +
+ Capacity on Demand (CoD) Option + + Platforms may optionally provide mechanisms for securely licensing + a subset of the platform’s physically installed resources for use. + The CoD option includes system parameters relating to the CoD Capacity + “smart card” which is used to securely store and validate the + license information. Dynamically adding memory and cpu resources to + running partitions requires the CoD option combined with the Logical + Resource Dynamic Reconfiguration option. + Additionally platforms may provide a provisional CoD activation + mode known as “Trial CoD”. This mode provides immediate + availability of resources while the permanent license is on order. The + CoD resources are made available for a platform dependent period of power + on hours. + If the platform implements the CoD sparing option and the platform + predicts the failure of a CoD resource, given that there is spare + capacity of that resource, the platform makes available a spare resource + so that the OS can migrate work off the failing resource and return the + failing resource to the OS. If the OS takes advantage of this sparing, by + actually using the available resource the OS is using resources in excess + of the permanently licensed entitlement until the failing CoD resource is + returned to the platform. + + + + R1--1. + + For the CoD option: The + platform must support the System Parameter option + (ibm,get-system-parameter) + along with Parameter tokens 18 + and 19 as described in + . + + + + +
+ CoD Capacity Card Info + + + Software Note: System parameters 18 and 19 present + only permanently activated capacity. These parameters will be removed at + some point in the future. OSs should begin using the enhanced CoD + Capacity parameters. + These two read only system parameters (one for memory and another + for processors) are ASCII hexadecimal strings representing the current + licensed entitlement of CoD resources of their respective types. These + strings contains 9 packed fields as presented in + . + + + CoD Capacity Card Info String Packed Fields + + + + + + + + Field Number + + + + + Definition + + + + + + + + 1 + + + System type (4 ASCII characters) (4 bytes) + + + + + 2 + + + System serial number (8 ASCII characters: pp-sssss) (8 + bytes) + + + + + 3 + + + CoD capacity card Custom Card Identification Number + (CCIN) (4 ASCII characters) (4 bytes) + + + + + 4 + + + CoD capacity card serial number (10 ASCII characters: + pp-sssssss) (10 bytes) + + + + + 5 + + + CoD capacity card unique ID (16 ASCII characters) (16 + bytes) + + + + + 6 + + + CoD resource identifier (4 ASCII characters) (4 + bytes) + + + + + 7 + + + Quantity of Activated CoD resource (4 characters ASCII) + (4 bytes) + + + + + 8 + + + CoD sequence number (4 numeric ASCII characters) (4 + bytes) + + + + + 9 + + + CoD activation code entry check (1 byte hex check sum, + two ASCII characters - based on EBCDIC representation of items: + 1, 2, 3, 4, 5, 6, 7, and 8) (2 bytes) + + + + +
+ + + + R1--1. + + For the CoD option: The platform’s + ibm-get-system-parameter RTAS call, specifying the + CoD Capacity Card Info, must, upon successful completion, return the + ASCII representation of the information defined in + for the managed CoD resource + type specified by the system parameter token. + + + + + R1--2. + + For the CoD option: The platform’s + ibm,set-system-parameter RTAS call specifying the CoD + Capacity Card Info, must not return a + Status of 0 (success); the expected return is a + Status of -9002 (Setting not allowed/authorized), + however, under special cases a + Status of -1 (Hardware error), or one of the Busy or + Extended Delay return + Status return values is allowed. + + + + +
+ +
+ Predictive Failure Sparing with Free Resources + + A platform may optionally provide an unused resource to a partition + that is notified of a predictive failure. This allows the + partition’s OS to transparently substitute the spare resource for + the failing one in some situations. To take advantage of this situation, + the partition’s OS queries the free DR slot(s) of the resource type + to determine if a spare resource is available, and if so uses the other + DR RTAS calls to acquire the resource. In some cases resources are free + because they have not been assigned to partitions. + A platform may optionally provide an unused CoD resource to a + partition as a predictive failure spare. In such cases, the result of an + get-sensor-state (entity-sense) for the DR slot + returns the state of “exchange”. Between the time that the OS + takes ownership, via + set-indicator (allocation-state, exchange), of the + spare CoD resource available and the OS gives up the failing resource, + the platform exceeds the licensed entitlement for that resource. + + + + R1--1. + + For the Predictive Failure Sparing option: + The platform, upon provisionally making available a spare CoD resource in + response to a predictive failure, must set the CoD Resource Provisional + Activation timer, to time out the use of the provisionally activated + excess resources. + + + + +
+ +
+ Enhanced CoD Capacity Info + + These two read only system parameters (one for processor and one + for memory) return ASCII hexadecimal strings representing the current + licensed CoD resources. + The strings are constructed with a fixed “base” section + followed by zero or more optional sections. The definitions below show + all optional sections. The caller should not expect the presence or order + of all optional sections. Each optional section starts with the following + 3 members: + + + + Offset to next section (zero for last section) + + + + Size in bytes of the section (including these three + members) + + + + Name of the section + + + + The specific meaning of the members of each section is beyond the + scope of this architecture; refer to the specific platform design + documents. + All data in these tables are composed of printable ASCII + characters. There are no NULLs or other non-printable characters. + + Programming Note: On a platform where the base + processor capacity is a fraction of a full processor, the data in the + BaseProc section below is rounded up to the next larger whole + number. + + + + R1--1. + + For the CoD option: The platform's + ibm,get-system-parameter RTAS call, specifying the + Enhanced CoD Processor Capacity Info, must, upon successful completion, + return the ASCII representation of the information defined in + for managed CoD processor + resources. + + + Enhanced CoD Processor Capacity Info, Version + 1 + + + + + + + + + + + Offset + + + + + Size in Bytes + + + + + Section + + + + + Description + + + + + Format + + + + + + + + 0 + + + 4 + + + Meta + + + Table version indicator + + + 4 ASCII characters “V1 “ + + + + + 4 + + + 4 + + + Meta + + + Decimal number of optional sections + + + 4 ASCII numeric characters + + + + + 8 + + + 4 + + + Base + + + Decimal offset in bytes from the start of this section to + the start of the next section (that is, the offset from the + first byte of this member to the first byte of the next + section). Zero if the last section + + + 4 ASCII numeric characters + + + + + 12 + + + 4 + + + Base + + + Section Length -- The length of this section in bytes + (including offset member above) + + + 4 ASCII numeric characters “78 “ + + + + + 16 + + + 8 + + + Base + + + Section Name + + + 8 ASCII characters “BASE “ + + + + + 24 + + + 4 + + + Base + + + system type + + + 4 ASCII characters + + + + + 28 + + + 10 + + + Base + + + System serial number + + + 10 ASCII characters: “pp-ssssss “ + + + + + 38 + + + 4 + + + Base + + + CoD capacity card CCIN + + + 4 ASCII characters + + + + + 42 + + + 10 + + + Base + + + CoD capacity card serial number + + + 10 ASCII characters “hh-hssssss” + + + + + 52 + + + 16 + + + Base + + + CoD capacity card unique ID + + + 16 ASCII characters + + + + + 68 + + + 4 + + + Base + + + CoD resource identifier + + + 4 ASCII characters + + + + + 72 + + + 4 + + + Base + + + Quantity of permanently activated resources + + + 4 ASCII characters + + + + + 76 + + + 4 + + + Base + + + CoD sequence number + + + 4 numeric ASCII characters + + + + + 80 + + + 2 + + + Base + + + CoD activation code entry check + + + 1 byte hex check sum, 2 ASCII characters -- based on + EBCDIC representation of previous 8 entries. + + + + + 82 + + + 4 + + + Base + + + Total CoD resources installed in system + + + 4 numeric ASCII characters + + + + + On/Off Processor Resources + + + + + 0 + + + 4 + + + OnOffPrc + + + Decimal offset in bytes from the start of this section to + the start of the next section (that is, the offset from the + first byte of this member to the first byte of the next + section). Zero if the last section. + + + 4 ASCII numeric characters + + + + + 4 + + + 4 + + + OnOffPrc + + + Section Length -- The length of this section in bytes + (including offset member above) + + + 4 ASCII numeric characters “66 “ + + + + + 8 + + + 8 + + + OnOffPrc + + + Section Name + + + 8 ASCII characters “ONOFFPRC” + + + + + 16 + + + 1 + + + OnOffPrc + + + On/Off CoD enabled + + + 1 ASCII character '0' or '1' + + + + + 17 + + + 1 + + + OnOffPrc + + + On/Off CoD active + + + 1 ASCII character '0' or '1' + + + + + 18 + + + 4 + + + OnOffPrc + + + On/Off CoD feature + + + 4 ASCII characters + + + + + 22 + + + 4 + + + OnOffPrc + + + On/Off CoD activated resources + + + 4 ASCII numeric characters + + + + + 26 + + + 4 + + + OnOffPrc + + + On/Off CoD sequence number + + + 4 ASCII numeric characters + + + + + 30 + + + 2 + + + OnOffPrc + + + On/Off CoD checksum + + + 2 ASCII characters + + + + + 32 + + + 4 + + + OnOffPrc + + + On/Off CoD resources requested + + + 4 ASCII numeric characters + + + + + 36 + + + 4 + + + OnOffPrc + + + On/Off CoD days requested + + + 4 ASCII numeric characters + + + + + 40 + + + 4 + + + OnOffPrc + + + On/Off CoD resource days expired + + + 4 ASCII numeric characters + + + + + 44 + + + 4 + + + OnOffPrc + + + On/Off CoD resource days remaining + + + 4 ASCII numeric characters + + + + + 48 + + + 4 + + + OnOffPrc + + + On/Off CoD counter + + + 4 ASCII numeric characters + + + + + 52 + + + 4 + + + OnOffPrc + + + On/Off standby resources available + + + 4 ASCII numeric characters + + + + + 56 + + + 1 + + + OnOffPrc + + + On/Off reserved byte + + + 1 ASCII blank + + + + + 57 + + + 4 + + + OnOffPrc + + + On/Off history of requested resource days + + + 4 ASCII characters + + + + + 61 + + + 1 + + + OnOffPrc + + + On/Off reserved byte + + + 1 ASCII blank + + + + + 62 + + + 4 + + + OnOffPrc + + + On/Off history of unreturned resource days + + + 4 ASCII characters + + + + + Debit Processor Resources + + + + + 0 + + + 4 + + + DebitPrc + + + Decimal offset in bytes from the start of this section to + the start of the next section (that is, the offset from the + first byte of this member to the first byte of the next + section). Zero if the last section. + + + 4 ASCII numeric characters + + + + + 4 + + + 4 + + + DebitPrc + + + Section Length -- The length of this section in bytes + (including offset member above) + + + 4 ASCII numeric characters “82 “ + + + + + 8 + + + 8 + + + DebitPrc + + + Section Name + + + 8 ASCII characters “DEBITPRC” + + + + + 16 + + + 1 + + + DebitPrc + + + Debit CoD enabled + + + 1 ASCII character '0' or '1' + + + + + 17 + + + 1 + + + DebitPrc + + + Debit CoD active + + + 1 ASCII character '0' or '1' + + + + + 18 + + + 4 + + + DebitPrc + + + Debit CoD feature + + + 4 ASCII characters + + + + + 22 + + + 4 + + + DebitPrc + + + Debit CoD activated resources + + + 4 ASCII numeric characters + + + + + 26 + + + 4 + + + DebitPrc + + + Debit CoD sequence number + + + 4 ASCII numeric characters + + + + + 30 + + + 2 + + + DebitPrc + + + Debit CoD checksum + + + 2 ASCII characters + + + + + 32 + + + 4 + + + DebitPrc + + + Debit CoD resources requested + + + 4 ASCII numeric characters + + + + + 36 + + + 12 + + + DebitPrc + + + Debit Reserved + + + 12 ASCII blanks + + + + + 48 + + + 4 + + + DebitPrc + + + Debit counter + + + 4 ASCII characters + + + + + 52 + + + 4 + + + DebitPrc + + + Debit standby resources available + + + 4 ASCII numeric characters + + + + + 56 + + + 1 + + + DebitPrc + + + Debit reserved byte + + + 1 ASCII blank + + + + + 57 + + + 4 + + + DebitPrc + + + Debit history of expired resource days + + + 4 ASCII numeric characters + + + + + 61 + + + 1 + + + DebitPrc + + + Debit reserved byte + + + 1 ASCII blank + + + + + 62 + + + 4 + + + DebitPrc + + + Debit history of unreturned resource days + + + 4 ASCII characters + + + + + 66 + + + 8 + + + DebitPrc + + + Extended total history of requested On/Off Processor + days + + + 8 ASCII characters + + + + + 74 + + + 8 + + + DebitPrc + + + Extended total history of unreturned On/Off Processor + days + + + 8 ASCII characters + + + + + Trial Processor Resources + + + + + 0 + + + 4 + + + TrialPrc + + + Decimal offset in bytes from the start of this section to + the start of the next section (that is, the offset from the + first byte of this member to the first byte of the next + section). Zero if the last section. + + + 4 ASCII numeric characters + + + + + 4 + + + 4 + + + TrialPrc + + + Section Length -- The length of this section in bytes + (including offset member above) + + + 4 ASCII numeric characters “66 “ + + + + + 8 + + + 8 + + + TrialPrc + + + Section Name + + + 8 ASCII characters “TRIALPRC” + + + + + 16 + + + 1 + + + TrialPrc + + + Trial CoD enabled + + + 1 ASCII character '0' or '1' + + + + + 17 + + + 1 + + + TrialPrc + + + Trial reserved + + + 1 ASCII blank + + + + + 18 + + + 4 + + + TrialPrc + + + Trial CoD feature + + + 4 ASCII characters + + + + + 22 + + + 4 + + + TrialPrc + + + Trial CoD activated resources + + + 4 ASCII numeric characters + + + + + 26 + + + 4 + + + TrialPrc + + + Trial CoD sequence number + + + 4 ASCII numeric characters + + + + + 30 + + + 2 + + + TrialPrc + + + Trial CoD checksum + + + 2 ASCII characters + + + + + 32 + + + 8 + + + TrialPrc + + + Trial reserved bytes + + + 8 ASCII blanks + + + + + 40 + + + 4 + + + TrialPrc + + + Trial days expired + + + 4 ASCII numeric characters + + + + + 44 + + + 4 + + + TrialPrc + + + Trial days remaining + + + 4 ASCII numeric characters + + + + + 48 + + + 14 + + + TrialPrc + + + Trial reserved bytes + + + 14 ASCII blanks + + + + + 62 + + + 4 + + + TrialPrc + + + Trial unreturned resources + + + 4 ASCII numeric characters + + + + + Base Processor Resources + + + + + 0 + + + 4 + + + BaseProc + + + Decimal offset in bytes from the start of this section to + the start of the next section (that is, the offset from the + first byte of this member to the first byte of the next + section). Zero if the last section. + + + 4 ASCII numeric characters + + + + + 4 + + + 4 + + + BaseProc + + + Section Length -- The length of this section in bytes + (including offset member above) + + + 4 ASCII numeric characters “20 “ + + + + + 8 + + + 8 + + + BaseProc + + + Section Name + + + 8 ASCII characters “BASEPROC” + + + + + 16 + + + 4 + + + BaseProc + + + Number of Non-CoD “Base” processors on this + system. NOTE: If this section is not present, there are no + “base” processors and all processors are CoD + activated. + + + 4 ASCII numeric characters + + + + +
+ + + + + R1--2. + + For the CoD option: The platform's + ibm,get-system-parameter RTAS call, specifying the + Enhanced CoD Memory Capacity Info, must, upon successful completion, + return the ASCII representation of the information defined in + for the managed CoD memory + resources. + + + Enhanced CoD Memory Capacity Info, Version 1 + + + + + + + + + + + Offset + + + + + Size in Bytes + + + + + Section + + + + + Description + + + + + Format + + + + + + + + 0 + + + 4 + + + Meta + + + Table version indicator + + + 4 ASCII characters “V1 ” + + + + + 4 + + + 4 + + + Meta + + + Decimal number of optional sections + + + 4 ASCII numeric characters + + + + + 8 + + + 4 + + + Base + + + Decimal offset in bytes from the start of this section to + the start of the next section (that is, the offset from the + first byte of this member to the first byte of the next + section). Zero if the last section. + + + 4 ASCII numeric characters + + + + + 12 + + + 4 + + + Base + + + Section Length -- The length of this section in bytes + (including offset member above) + + + 4 ASCII numeric characters “78 ” + + + + + 16 + + + 8 + + + Base + + + Section Name + + + 8 ASCII characters “BASE ” + + + + + 24 + + + 4 + + + Base + + + system type + + + 4 ASCII characters + + + + + 28 + + + 10 + + + Base + + + System serial number + + + 10 ASCII characters: “pp-ssssss ” + + + + + 38 + + + 4 + + + Base + + + CoD capacity card CCIN + + + 4 ASCII characters + + + + + 42 + + + 10 + + + Base + + + CoD capacity card serial number + + + 10 ASCII characters “hh-hssssss” + + + + + 52 + + + 16 + + + Base + + + CoD capacity card unique ID + + + 16 ASCII characters + + + + + 68 + + + 4 + + + Base + + + CoD resource identifier + + + 4 ASCII characters + + + + + 72 + + + 4 + + + Base + + + Quantity of permanently activated resources + + + 4 ASCII characters + + + + + 76 + + + 4 + + + Base + + + CoD sequence number + + + 4 numeric ASCII characters + + + + + 80 + + + 2 + + + Base + + + CoD activation code entry check + + + 1 byte hex check sum, 2 ASCII characters -- based on + EBCDIC representation of previous 8 entries. + + + + + 82 + + + 4 + + + Base + + + Total CoD resources installed in system + + + 4 numeric ASCII characters + + + + + On/Off Memory Resources + + + + + 0 + + + 4 + + + OnOffMem + + + Decimal offset in bytes from the start of this section to + the start of the next section (that is, the offset from the + first byte of this member to the first byte of the next + section). Zero if the last section. + + + 4 ASCII numeric characters + + + + + 4 + + + 4 + + + OnOffMem + + + Section Length -- The length of this section in bytes + (including offset member above) + + + 4 ASCII numeric characters “67 “ + + + + + 8 + + + 8 + + + OnOffMem + + + Section Name + + + 8 ASCII characters “ONOFFMEM” + + + + + 16 + + + 1 + + + OnOffMem + + + On/Off CoD enabled + + + 1 ASCII character '0' or '1' + + + + + 17 + + + 1 + + + OnOffMem + + + On/Off CoD active + + + 1 ASCII character '0' or '1' + + + + + 18 + + + 4 + + + OnOffMem + + + On/Off CoD feature + + + 4 ASCII characters + + + + + 22 + + + 4 + + + OnOffMem + + + On/Off CoD activated resources + + + 4 ASCII numeric characters + + + + + 26 + + + 4 + + + OnOffMem + + + On/Off CoD sequence number + + + 4 ASCII numeric characters + + + + + 30 + + + 2 + + + OnOffMem + + + On/Off CoD checksum + + + 2 ASCII characters + + + + + 32 + + + 4 + + + OnOffMem + + + On/Off CoD resources requested + + + 4 ASCII numeric characters + + + + + 36 + + + 4 + + + OnOffMem + + + On/Off CoD days requested + + + 4 ASCII numeric characters + + + + + 40 + + + 4 + + + OnOffMem + + + On/Off CoD resource days expired + + + 4 ASCII numeric characters + + + + + 44 + + + 4 + + + OnOffMem + + + On/Off CoD resource days remaining + + + 4 ASCII numeric characters + + + + + 48 + + + 4 + + + OnOffMem + + + On/Off CoD counter + + + 4 ASCII numeric characters + + + + + 52 + + + 4 + + + OnOffMem + + + On/Off standby resources available + + + 4 ASCII numeric characters + + + + + 56 + + + 1 + + + OnOffMem + + + On/Off reserved byte + + + 1 ASCII blank + + + + + 57 + + + 4 + + + OnOffMem + + + On/Off history of requested resource days + + + 4 ASCII characters + + + + + 61 + + + 1 + + + OnOffMem + + + On/Off reserved byte + + + 1 ASCII blank + + + + + 62 + + + 4 + + + OnOffMem + + + On/Off history of unreturned resource days + + + 4 ASCII characters + + + + + 66 + + + 1 + + + OnOffMem + + + On/Off Memory Multiplier + + + 1 ASCII numeric characters + + + + + Debit Memory Resources + + + + + 0 + + + 4 + + + DebitMem + + + Decimal offset in bytes from the start of this section to + the start of the next section (that is, the offset from the + first byte of this member to the first byte of the next + section). Zero if the last section. + + + 4 ASCII numeric characters + + + + + 4 + + + 4 + + + DebitMem + + + Section Length -- The length of this section in bytes + (including offset member above) + + + 4 ASCII numeric characters “83 “ + + + + + 8 + + + 8 + + + DebitMem + + + Section Name + + + 8 ASCII characters “DEBITMEM” + + + + + 16 + + + 1 + + + DebitMem + + + Debit CoD enabled + + + 1 ASCII character '0' or '1' + + + + + 17 + + + 1 + + + DebitMem + + + Debit CoD active + + + 1 ASCII character '0' or '1' + + + + + 18 + + + 4 + + + DebitMem + + + Debit CoD feature + + + 4 ASCII characters + + + + + 22 + + + 4 + + + DebitMem + + + Debit CoD activated resources + + + 4 ASCII numeric characters + + + + + 26 + + + 4 + + + DebitMem + + + Debit CoD sequence number + + + 4 ASCII numeric characters + + + + + 30 + + + 2 + + + DebitMem + + + Debit CoD checksum + + + 2 ASCII characters + + + + + 32 + + + 4 + + + DebitMem + + + Debit CoD resources requested + + + 4 ASCII numeric characters + + + + + 36 + + + 12 + + + DebitMem + + + Debit Reserved + + + 12 ASCII blanks + + + + + 48 + + + 4 + + + DebitMem + + + Debit counter + + + 4 ASCII characters + + + + + 52 + + + 4 + + + DebitMem + + + Debit standby resources available + + + 4 ASCII numeric characters + + + + + 56 + + + 1 + + + DebitMem + + + Debit reserved byte + + + 1 ASCII blank + + + + + 57 + + + 4 + + + DebitMem + + + Debit history of expired resource days + + + 4 ASCII numeric characters + + + + + 61 + + + 1 + + + DebitMem + + + Debit reserved byte + + + 1 ASCII blank + + + + + 62 + + + 4 + + + DebitMem + + + Debit history of unreturned resource days + + + 4 ASCII characters + + + + + 66 + + + 8 + + + DebitMem + + + Extended total history of requested On/Off Memory GB + days + + + 8 ASCII characters + + + + + 74 + + + 8 + + + DebitMem + + + Extended total history of unreturned On/Off Memory GB + days + + + 8 ASCII characters + + + + + 82 + + + 1 + + + DebitMem + + + Debit reserved byte + + + 1 ASCII blank + + + + + Trial Memory Resources + + + + + 0 + + + 4 + + + TrialMem + + + Decimal offset in bytes from the start of this section to + the start of the next section (that is, the offset from the + first byte of this member to the first byte of the next + section). Zero if the last section. + + + 4 ASCII numeric characters + + + + + 4 + + + 4 + + + TrialMem + + + Section Length -- The length of this section in bytes + (including offset member above) + + + 4 ASCII numeric characters “67 ” + + + + + 8 + + + 8 + + + TrialMem + + + Section Name + + + 8 ASCII characters “TRIALMEM” + + + + + 16 + + + 1 + + + TrialMem + + + Trial CoD enabled + + + 1 ASCII character '0' or '1' + + + + + 17 + + + 1 + + + TrialMem + + + Trial reserved + + + 1 ASCII blank + + + + + 18 + + + 4 + + + TrialMem + + + Trial CoD feature + + + 4 ASCII characters + + + + + 22 + + + 4 + + + TrialMem + + + Trial CoD activated resources + + + 4 ASCII numeric characters + + + + + 26 + + + 4 + + + TrialMem + + + Trial CoD sequence number + + + 4 ASCII numeric characters + + + + + 30 + + + 2 + + + TrialMem + + + Trial CoD checksum + + + 2 ASCII characters + + + + + 32 + + + 8 + + + TrialMem + + + Trial reserved bytes + + + 8 ASCII blanks + + + + + 40 + + + 4 + + + TrialMem + + + Trial days expired + + + 4 ASCII numeric characters + + + + + 44 + + + 4 + + + TrialMem + + + Trial days remaining + + + 4 ASCII numeric characters + + + + + 48 + + + 14 + + + TrialMem + + + Trial reserved bytes + + + 14 ASCII blanks + + + + + 62 + + + 4 + + + TrialMem + + + Trial unreturned resources + + + 4 ASCII numeric characters + + + + + 66 + + + 1 + + + TrialMem + + + Trial reserved byte + + + 1 ASCII blank + + + + +
+ + + + + R1--3. + + For the CoD option: The platform's + ibm,set-system-parameter RTAS call specifying the + Enhanced CoD Capacity Info, must not return a + Status of 0 (Success); the expected return is a + Status of -9002 (setting not allowed/authorized), + however, under special cases a + Status of -1 (Hardware Error) or one of the Busy or + Extended Delay return + Status values is allowed. + + + + +
+ +
+ +
+ <emphasis>Restart Parameters</emphasis> + + This section and its subsections describe parameters that govern + the actions that the platform firmware takes upon a restart (that is, + reboot) after an unintended termination. + +
+ partition_auto_restart Parameter + + The partition_auto_restart parameter governs whether or not + platform firmware attempts to restart a partition after an error which + causes an abnormal partition termination. Neither a loss of external + power without a UPS, nor a loss of external power and battery power with + a UPS are examples of an error which causes abnormal partition + termination. For terminations that involve only a specific partition (for + example, a machine check), the partition_auto_restart parameter governs + whether the partition restarts. For terminations that span the entire + platform (for example, a checkstop), the platform may separately govern + whether or not the entire platform restarts. If the platform does + restart, however, partition_auto_restart determines whether or not an + individual partition restarts. + + + + R1--1. + + For the LPAR option with the System Parameters + option: If the platform supports the partition_auto_restart + system parameter, the platform must establish and maintain across boot + (unless explicitly altered by a user) for each partition the one (1) byte + parameter, the initial value (depending upon platform policy) is one of + the following binary values: + 0 - Do not automatically restart the partition + 1 - Automatically restart the partition + + + + + R1--2. + + For the SMP option (non-LPAR) with the System Parameters + option: If the platform supports the partition_auto_restart + system parameter, the platform must establish and maintain across boot + (unless explicitly altered by a user) one and only one (1) byte + parameter, the initial value (depending upon platform policy) is one of + the following binary values: + 0 - Do not automatically restart the OS + 1 - Automatically restart the OS + + + + +
+ +
+ platform_auto_power_restart Parameter + + The platform_auto_power_restart parameter governs whether or not + platform firmware attempts to restart after power is restored following a + power outage. + + + + R1--1. + + For the System Parameters option: If + the platform + supports the platform_auto_power_restart system parameter, the platform + must maintain across boot (unless explicitly altered by a user) one and + only one platform wide value of the one (1) byte parameter having one of + the following binary values: + 0 - Do not automatically restart + 1 - Automatically restart partitions that were active when external + power was lost. + + + + + R1--2. + + For the LPAR option with the System Parameters + option: If the platform supports the + platform_auto_power_restart system parameter, the platform must provide + the authority to set and read the platform_auto_power_restart system + parameter to, at most, one partition at a time. + + + + +
+ +
+ +
+ Remote Serial Port System Management Parameters + + + + R1--1. + + For the LPAR option with the System Parameters + option: If the platform supports any of the following system + parameters: sp-remote-pon, sp-rb4-pon, sp-snoop-str, and sp-serial-snoop; + the platform must grant authority to set and read the single platform + wide values of the respective system parameters to only the partition + owning the resource required to implement the function, such as a serial + port, where the valid data for the parameters are specified in + . + + + + + R1--2. + + For the System Parameters option: The + platform must + support the sp-rb4-pon system parameter if and only if the sp-remote-pon + system parameter is supported and implemented by using “Ring + Indicate” of a serial port. + + + + + R1--3. + + For the LPAR option with the System Parameters + option: Platforms that supports the sp-snoop-str system + parameter must maintain one and only one platform wide NULL terminated + ASCII string value of the parameter; granting authority to set and read + the sp-snoop-str system parameter to, at most, one partition at a + time. + + + + + R1--4. + + For the System Parameters option: To prevent return + data truncation of the returned sp-snoop-str system parameter from the + ibm,get-system-parameter RTAS call the caller must + supply a buffer length sufficient to contain the two string length bytes + plus the ASCII string and the terminating ASCII NULL. + + + + + R1--5. + + For the System Parameters option: The + caller of the + ibm,get-system-parameter RTAS call must supply a + buffer length sufficient to contain the two string length bytes plus the + ASCII string and the terminating ASCII NULL to prevent return data + truncation of the returned sp-snoop-str system parameter. + + + + + R1--6. + + For the System Parameters option: The + platform must + supports both the sp-snoop-str and sp-serial-snoop system parameters if + it supports either. + + + + +
+ +
+ Surveillance Parameters + + For the definition of the sp-sen, sp-sti, and sp-del parameters, + see + . + + + + R1--1. + + For the LPAR option + with the System Parameters option: If the platform + supports any of the following system parameters: sp-sen, sp-sti, or + sp-del; the platform must grant authority to set and read the single + platform wide one (1) byte values, where the decimal representation is + defined in + , of the respective system + parameters to only one partition at a time. + + + + + R1--2. + + For the System Parameters option: If the platform + supports any of the sp-sen, sp-sti or sp-del system parameters, it must + support then all. + + + + +
+ +
+ Call Home Parameter + + This parameter is used to provide input concerning certain call + home values used when a call home function is provided. The data for the + parameter is an ASCII string which provides additional information + + + + R1--1. + + For the LPAR option with the System Parameters + option: If the platform supports the sp-call-home parameter, + platform must grant authority to set and read the single platform wide + value of the system parameter at any time to only one partition; where + the data for the parameter is an ASCII string in the form + <String_name1>=<string><ASCII + NULL><String_name2>=<string><ASCII + NULL>....<String_nameN>=<string><ASCII + NULL><ASCII NULL> with string names defined as per + . + + + + + R1--2. + + For the System Parameters option: The + caller of the + ibm,get-system-parameter RTAS call must supply a + buffer length sufficient to contain the maximum possible ASCII string + returned, including the two ASCII NULLs where + indicates the maximum length of + the data for each substring that comprises the sp-call-home data, to + prevent return data truncation of the returned sp-call-home system + parameter. + + + + + R1--3. + + For the System Parameters + option: If the platform + supports the sp-call-home parameter, the platform must provide the + sp-call-home parameter value defaults listed in + prior to any + ibm,set-system-parameter RTAS call. + + + sp-call-home Strings + + + + + + + + + + + String_Name + + + + + Default + + + + + Range + + + + + Maximum Characters in String + Data + + + + + Description + + + + + + + + sp-rt-s<N> + + + NULL + + +   + + + 20 + + + Retry string for serial port <N> + + + + + sp-ic-s<N> + + + NULL + + +   + + + 12 + + + Protocol interdata block delay (*IC) for serial port + <N> + + + + + sp-to-s<N> + + + NULL + + +   + + + 12 + + + Protocol time out (*DT) for serial port <N> + + + + + sp-cd-s<N> + + + NULL + + +   + + + 12 + + + Call Delay (*CD) for serial port <N> + + + + + sp-connect-s<N> + + + NULL + + +   + + + 12 + + + Connect (*CX) for serial port <N> + + + + + sp-disconnect-s<N> + + + NULL + + +   + + + 12 + + + Disconnect (*DX) for serial port <N> + + + + + sp-condout-s<N> + + + NULL + + +   + + + 12 + + + Call-out condition (*C0) for serial port <N> + + + + + sp-condwait-s<N> + + + NULL + + +   + + + 12 + + + Call-wait (*C0) for serial port <N> + + + + + sp-condin-s<N> + + + NULL + + +   + + + 12 + + + Call-in condition (*C1) for serial port <N> + + + + + sp-waitcall-s<N> + + + NULL + + +   + + + 12 + + + Wait call (*WC) for serial port <N> + + + + + sp-page-s<N> + + + NULL + + +   + + + 20 + + + Describes how to Page a beeper for serial port + <N> + + + + + sp-diok-s<N> + + + off + + + on,off + + + 4 + + + Serial Port <N> Call-in (Dial in authorized on the + port) + + + + + sp-dook-s<N> + + + off + + + on,off + + + 4 + + + Serial Port <N> Call-out (Dial out authorized on + the port) + + + + + sp-dookc + + + off + + + on,off + + + 4 + + + Call-out before restart (Dial out for system crash using + authorized serial port) + + + + + sp-ls-s<N> + + + 9600 + + + 300, 600, 1200, 2000, 2400, 3600, 4800, 7200, 9600, + 19200, 38400 + + + 6 + + + S<N> line speed + + + + + sp-modemf-s<N> + + + NULL + + +   + + + 120 + + + Filename of the last modem file used to configure modem + parameters + + + + + sp-phsvc + + + 20 blank characters + + + 20 characters max + + + 20 + + + Service Center Telephone Number (*PS) + + + + + sp-phadm + + + 20 blank characters + + + 20 characters max + + + 20 + + + Customer Administration Center Telephone Number + (*PH) + + + + + sp-pager + + + 20 blank characters + + + 20 characters max + + + 20 + + + Digital Pager Telephone Number + + + + + sp-phsys + + + 20 blank characters + + + 20 characters max + + + 20 + + + Customer System Telephone number (*PY) + + + + + sp-vox + + + 20 blank characters + + + 20 characters max + + + 20 + + + Customer Voice telephone number (*PO) + + + + + sp-acct + + + 12 blank characters + + + 12 characters max + + + 12 + + + Customer Account Number (*CA) + + + + + sp-cop + + + first + + + first, all + + + 6 + + + Call-out policy (first/all) - numbers to call in case of + failure + + + + + sp-retlogid + + + 12 blank characters + + + 12 characters max + + + 12 + + + Customer RETAIN Login Userid (*LI) + + + + + sp-retpw + + + 16 blank characters + + + 16 characters max + + + 12 + + + Customer RETAIN Login password (*PW) + + + + + sp-rto + + + 120 + + + >1 + + + 12 + + + Remote Timeout (in seconds) (*RT) + + + + + sp-rlat + + + 2 + + + > 1 + + + 12 + + + Remote Latency (in seconds) (*RL) + + + + + sp-rn + + + 2 + + + 0 or any positive number + + + 12 + + + Number of retries (while busy (*RN)) + + + + + sp-sysname + + + 15 blank characters + + + 15 characters max + + + 15 + + + System Name (system administrator aid) + + + + +
+ + Notes: + + + + + <N> is substituted with a modem number, i.e. 1 or + 2. + + + + NULL as a default indicates that the string is given a name, but + no value, e.g. sp-modemf-s= + + + + + + +
+ +
+ Current Flash Image Parameter + + In systems with storage for more than one Flash image, the + sp-current-flash-image parameter indicates which Flash image is currently + being used by the service processor. This is typically the Flash image + used at the last boot. + + + + R1--1. + + For the LPAR option + with the System Parameters option: Platforms that + supports the sp-current-flash-image system parameter, must authorize all + partitions to get the single platform wide one (1) byte value of the + system parameter, whose decimal representation is defined in + . + + + + + R1--2. + + For the System Parameters option: Platforms that + supports the sp-current-flash-image system parameter must support the + ibm,manage-flash-image RTAS call. + + + + +
+ +
+ Platform Dump Max Size Parameter + + This parameter indicates the size (in bytes) needed for dumps + returned from the + ibm,platform-dump RTAS function. + + + + R1--1. + + For the Platform Dump option: If the + ibm,platform-dump RTAS call is authorized for the + partition, the platform must authorize the partition to get the + platform-dump-max-size system parameter; where the value returned must + indicate the sum (in bytes) of the maximum size of each unique platform + dump type that the + ibm,platform-dump RTAS call could return. + + + + + + Programming Note: The intent of + platform-dump-max-size is for the platform to specify, in advance, the + sum of the maximum sizes of all the unique dump types that it can + generate. This is to allow the OS to reserve space for one log of each + type. In the case of any change in the value of this parameter, the + platform may generate a Platform Event Log entry announcing the change in + the maximum size, and specifying the new size in the IO Events Section. + This entry, when generated, is then returned by the + event-scan RTAS call. +
+ +
+ Storage Preservation Option System Parameters + + The epow3-quiesce-time system parameter contains the time granted + to the current instance of a client program to perform quiesce activities + in preparation for a memory preservation boot. This quiesce time is the + time used by the client program to do such things as quiesce and power + off I/O not needed for memory preservation boot processing, in order to + conserve batteries. A client program utilizing the Storage Preservation + option, upon completion of quiesce activities, requests a reboot. The + platform, upon seeing an EPOW class 3 condition, and if both the + memory-preservation-boot-time and epow3-quiesce-time system parameters + are non-zero, starts a timer with an initial value equal to the + epow3-quiesce-time. If the timer expires before the client program + performs a reboot, the platform forces a reboot of the client + program. + The memory-preservation-boot-time system parameter contains the + time granted to the rebooted instance of the partition to perform the + saving of preserved memory. The client program, upon completion of the + saving of preserved memory, requests a shutdown. The platform, upon + initiation of a memory preservation boot starts a timer with an initial + value equal to the memory-preservation-boot-time, providing the value of + the memory-preservation-boot-time parameter is non-zero. If the timer + expires before the client program performs a shutdown, the platform + forces a shutdown of the client program. + Thus, the platform uses the memory-preservation-boot-time system + parameter as a policy attribute. If the client program has set the value + of this parameter to a non-zero value, then the memory preservation boot + timers are enabled. If the memory-preservation-boot-time parameter is + zero (independent of the epow3-quiesce-time setting), the platform does + not initiate the memory preservation boot timers. + To use the memory preservation boot timers, the client program + registers its LMBs for preservation and sets the + memory-preservation-boot-time via the + ibm,set-system-parameter RTAS call. If an EPOW class + 3 is sent to a client program and the client program has set its + memory-preservation-boot-time parameter, then the platform starts the + timer for epow3-quiesce-time. The client program on reboot uses the + get-sensor RTAS call (to detect EPOW condition) and + the + “ibm,preserved-storage” property in the + device tree to drive memory preservation processing as necessary. The + values of memory-preservation-boot-time and epow3-quiesce-time prior to + being set for a client program are 0. These system parameters are + persisted, as are all system parameters. + + + + R1--1. + + For the Storage Preservation option: The platform + must implement the memory-preservation-boot-time and epow3-quiesce-time + system parameters and must set their initial values to 0. + + + + + R1--2. + + For the Storage Preservation option: If the + memory-preservation-boot-time system parameter is non-zero for a client + program and if the platform delivers an EPOW class 3 indication to the + client program, the platform must do all of the following: + + + Upon delivering the EPOW class 3 to the client program, if the + epow3-quiesce-time system parameter is non-zero, then set a timer based + on the client program’s epow3-quiesce-time system parameter and + force a reboot of the client program on timer expiration, if the client + program does not request a reboot itself before the timer expires. + + + + Upon initiation of the memory preservation boot, set a timer + based on the client program’s memory-preservation-boot-time system + parameter and on timer expiration, force a shutdown of the client program + if the client program does not request a shutdown itself before the timer + expires. + + + + + + +
+ +
+ SCSI Initiator Identifier System Parameters + + Certain physical SCSI IOAs maintain their previous settings for + SCSI initiator identifier, while others require that the platform set + this value during I/O adapter initialization. Since the initialization of + I/O adapters in the boot path is done by firmware, a method is required + for the OS to inform the platform firmware of such settings. Given that + an OS owns a slot, and that slot contains a supported SCSI I/O adapter, + the OS may use the + ibm,set-system-parameter RTAS call specifying SCSI + Initiator Identifier system parameters to instruct the firmware how to + initialize the I/O adapter to ensure that it does not conflict with other + SCSI initiators on the same bus. The + ibm,get-system-parameter RTAS call is used to verify + the SCSI Initiator Identifier system parameters value for any OS owned + slot. + When + ibm,set-system-parameter is called specifying SCSI + Initiator Identifier system parameters, the buffer contains the standard + two byte length field plus two NULL terminated strings. The first string + contains the location code of an I/O Adapter's SCSI bus connector, and + the second string contains one of the decimal values 0-15 representing + the value of the SCSI Initiator Identifier that the platform's firmware + is to use to initialize the SCSI controller for that bus. + When + ibm,get-system-parameter is called specifying SCSI + Initiator Identifier system parameters, the buffer contains the standard + two byte length field plus a NULL terminated string that contains the + location code of an I/O Adapter's SCSI bus connector. Upon successful + return, the buffer contains the standard two byte length field plus two + NULL terminated strings. The first string contains the location code of + the I/O Adapter's SCSI bus connector, and the second string contains one + of the decimal values 0-15 representing the value of the SCSI Initiator + Identifier that the platform's firmware is to use to initialize the SCSI + controller for that bus. + + Implementation Note: For IOAs that have multiple + connectors per bus, the location code specifies the connector for the + external bus. + Interaction between SCSI Initiator Identifier system parameters and + DR operations produce unique situations. The platform maintains only the + latest SCSI Initiator Identifier set for any given location code. On DR + operations, the value is normally retained until the IOA owner explicitly + changes it. If a DR operation replaces the original IOA with a different + type of IOA, such that the previously set SCSI Initiator Identifier + system parameters no longer make sense (IOA is not a supported SCSI + adapter or the connector location codes do not match), the platform + firmware clears the SCSI Initiator Identifier system parameters for the + location code and performs the platform default IOA + initialization. + + + + R1--1. + + For the SCSI Initiator Identifier System Parameters + option: + When ibm,set-system-parameter is called specifying SCSI + Initiator Identifier system parameters, RTAS must return + Status of -3 (Parameter error) on any of the + following conditions: + + + + The binary value of the first two bytes in the buffer, plus 2, + is greater than the buffer length parameter. + + + + The buffer length parameter is greater than 1026. + + + + The N bytes of buffer contents (N being the binary value of the + first two buffer bytes) does not contain two NULL terminated + strings. + + + + The contents of the first NULL terminated buffer string does not + match the format of a valid platform location code. + + + + The contents of the second NULL terminated buffer string does + not contain a decimal value in the range of 0 to 15. + + + + + + + R1--2. + + For the SCSI Initiator Identifier System Parameters + option: + When ibm,set-system-parameter is called specifying SCSI + Initiator Identifier system parameters, and the request successfully + passes the Requirements of + , the first NULL terminated + buffer string must contain a valid formatted platform location code for a + currently installed slot owned by the calling OS, or the platform must + return “Not authorized” + Status. + + + + + R1--3. + + For the SCSI Initiator Identifier System Parameters + option: + When ibm,set-system-parameter is called specifying SCSI + Initiator Identifier system parameters, and the request successfully + passes the Requirements of + , the first NULL terminated + buffer string must contain a valid formatted platform location code for a + SCSI bus connector of a supported SCSI I/O adapter currently installed in + a slot owned by the calling OS, or the platform must return + “Parameter Error” + Status. + + + + + R1--4. + + For the SCSI Initiator Identifier System Parameters + option: When + ibm,set-system-parameter is called specifying SCSI + Initiator Identifier system parameters, and the request successfully + passes the Requirements of + , the firmware must record the + value supplied in the second NULL terminated buffer string for use in + initializing the SCSI initiator identifier of the SCSI I/O adapter + contained in the slot specified by the first NULL terminated buffer + string and return a + Status of 0 (success) (except in the case of hardware + errors or busy conditions). + + + + + R1--5. + + For the SCSI Initiator Identifier System Parameters + option: + When ibm,get-system-parameter is called specifying SCSI + Initiator Identifier system parameters, RTAS must return a + Status of -3 (Parameter error) on any of the + following conditions: + + + + The binary value of the first two bytes in the buffer, plus 2, + is greater than the buffer length parameter. + + + + The buffer length parameter is greater than 1026. + + + + The N bytes of buffer contents (N being the binary value of the + first two buffer bytes) does not contain one NULL terminated + string. + + + + The contents of the NULL terminated buffer string does not match + the format of a valid platform location code. + + + + + + + R1--6. + + For the SCSI Initiator Identifier System Parameters + option: + When ibm,get-system-parameter is called specifying SCSI + Initiator Identifier system parameters, and the request successfully + passes the Requirements of + , the NULL terminated buffer + string must contain a valid formatted platform location code for a + currently installed slot owned by the calling OS, or the platform must + return “Not authorized” + Status. + + + + + R1--7. + + For the SCSI Initiator Identifier System Parameters + option: + When ibm,get-system-parameter is called specifying SCSI + Initiator Identifier system parameters, and the request successfully + passes the Requirements of + , the NULL terminated buffer + string must contain a valid formatted platform location code for a SCSI + bus connector of a supported SCSI I/O adapter currently installed in a + slot owned by the calling OS, or the platform must return a + Status of -3 (parameter error). + + + + + R1--8. + + For the SCSI Initiator Identifier System Parameters + option: When + ibm,get-system-parameter is called specifying SCSI + Initiator Identifier system parameters, and the request successfully + passes the Requirements of + , the firmware must: + + + + Increase the value contained in the first two bytes of the + buffer to cover both the length of the location code NULL terminated + string and a NULL terminated string representing the decimal value that + the platform uses to initialize the SCSI initiator identifier of the SCSI + I/O adapter contained in the slot specified by the first NULL terminated + buffer string. + + + + If there is room in the buffer, append the NULL terminated + string representing the decimal value that the platform uses to + initialize the SCSI initiator identifier of the SCSI I/O adapter + contained in the slot specified by the first NULL terminated buffer + string. + + + + Return a Status of 0 (success) (except in the + case of hardware errors or busy conditions). + + + + + + + R1--9. + + For the SCSI Initiator Identifier System Parameters + option: When the platform firmware initializes an IOA and a + SCSI Initiator Identifier system parameter is set for that IOA's slot + location code, and the SCSI Initiator Identifier system parameter is + incompatible with the currently installed IOA (IOA is not a supported + SCSI adapter or the connector location codes do not match a SCSI bus + connector for that IOA), the platform must clear the incompatible SCSI + Initiator Identifier system parameter and proceed to initialize the IOA + using platform default behaviors. + + + + +
+ +
+ CoD Options + + The CoD Options system parameter allows specification of various + CoD options. + + + + R1--1. + + ibm,get-system-parameter is called + specifying the CoD Options system parameter, the first + two bytes of the value returned must + contain the full length of the parameter data, including the length of + the NULL. The two byte binary length field is followed by a variable of + the form “keyword” followed by “=” followed by + “value” and terminated by a semicolon (“;”), + where the contents of “value” must be an ASCII printable + character string. + + + + + R1--2. + + The corresponding keyword and values + for the CoD Options parameter are defined in + . + + + CoD Options System Parameter Keyword and + Values + + + + + + + + + Keyword + + + + + Permitted Values + + + + + Definition + + + + + + + + LPoptions + + + yes, no + + + no: The platform does not support the Low Priced adapters + and devices. + yes: The platform supports the Low Priced adapters and + devices. + Absence of the keyword is the same as the keyword with + the value of “yes”. + + + + +
+ + + + +
+ +
+ Platform Error Classification + + The Platform Error Classification system parameter specifies + whether the OS should process platform reported errors as informational + errors as opposed to service actionable events. + + + + R1--1. + + When + ibm,get-system-parameter is called specifying the + Platform Error Classification system parameter, the platform must return + a value of + “1” if all errors returned in + event-scan, + check-exception, + rtas-last-error and + ibm,slot-error-detail calls should be treated as + informational errors in the sense that they not be reported by service + applications as service actionable events and otherwise must return a + value of + “0”. + + + + + + Programming Note: Service applications within an + operating system may obtain information about platform errors and take + service actions (such as reporting the errors to a call center or other + error aggregation point) based on errors logged. Service applications + running in multiple partitions, each receiving platform error events, may + all report the same error to an aggregation point causing duplicated + error reports. To eliminate this duplication, a platform might choose to + log errors to only one partition in a system. That, however, would leave + an incomplete error record in individual partition and eliminate + notifications that each partition OS should be aware of (such as EPOW + events). + To allow platform errors to be reported to an OS, but prevent the + forwarding of the errors as service actionable events to an error + aggregation point, the Platform Error Classification system parameter may + be set to a value of 1. + The OS should not change how it logs an error based on this + parameter, nor should the OS change any error severity associated with + the log based on the parameter. Rather it is left to service applications + to query the system parameter and take actions based on it. +
+ +
+ Firmware Boot Options + + The Firmware Boot Options system parameter allows specification of + various firmware boot settings. + + + + R1--1. + + When ibm,get-system-parameter is called specifying the + Firmware Boot Options system parameter, the first two bytes of the value + returned must be binary and must contain the full length of the parameter + data, including the length of the NULL, and the field following length + field must be a variable of the form: “keyword” followed by + “=” followed by “value” and terminated by a + semicolon (“;”), where the contents of “value” + must be an ASCII printable character string. + + + + + R1--2. + + When ibm,set-system-parameter is + called specifying the + Firmware Boot Options system parameter, the first two bytes of the buffer + must be binary and must contain the full length of the parameter data, + including the length of the NULL, and the field following length field + must be a variable of the form: “keyword” followed by + “=” followed by “value” and terminated by a + semicolon (“;”), where the contents of “value” + must be an ASCII printable character string, and if the caller is not + authorized to adjust at least one of the specified keywords, the call + must return with a status of -9002. + + + + + R1--3. + + Keyword and values for the Firmware + Boot Options parameter must be as defined in + . + + + Firmware Boot Options System Parameter Keywords and + Values + + + + + + + + + Keyword + + + + + Permitted Values + + + + + Definition + + + + + + + + PlatformBootSpeed + + + fast, slow + + + fast: The platform will perform a minimal set of hardware + tests before loading the OS. + slow: The platform will perform a comprehensive set of + hardware tests before loading the OS. + Absence of the keyword implies the platform does not + support an alterable boot speed. + + + + +
+ + + + +
+ +
+ Platform Processor Diagnostics Options + + The platform-processor-diagnostics-run-mode system parameter allows + the operating system to query or control how platform run-time processor + diagnostics are executed by the platform. Provision is made by this + parameter for the platform to execute run-time diagnostic tests to verify + various processor functions. These diagnostics tests typically would be + performed by the hypervisor against each processor in the system. + + + + R1--1. + + When + ibm,get-system-parameter is called with the + platform-processor-diagnostics-run-mode token, the platform must return a + one-byte parameter indicating the current run-mode of platform processor + diagnostics as one of the following: + + + + 0 = disabled: indicates that the platform will not run processor + run-time diagnostics. + + + + 1 = staggered: indicates that the platform is set to run + processor diagnostics on each processor on a periodic basis, but not + attempt to schedule the tests for all processors at the same time. The + frequency at which the tests will run are defined by the platform. + + + + 2 = immediate: indicates that the platform is currently in the + processor of running diagnostics against the processors in a system on a + non-staggered basis, either as a result of an “immediate” or + “periodic” setting. + + + + 3 = periodic: indicates that the platform is scheduled to run + diagnostics against all the processors in the system at a specific time + scheduled by the platform. + + + + + + + R1--2. + + When + ibm,set-system-parameter is called specifying the + platform-processor-diagnostics-run-mode token, the one-byte parameter + passed must indicate the run-mode of platform periodic diagnostics + desired as one of the following: + + + + 0 = disabled: indicates that the platform should not run any + processor run-time diagnostics. Any currently running diagnostics will be + terminated. + + + + 1 = staggered: indicates that the platform should run + diagnostics periodically against each processor in the system, but not + attempt to schedule the tests for all processors at the same time. The + frequency at which the tests will run are defined by the platform. + + + + 2 = immediate: indicates that the platform should immediately + begin the process of running processor diagnostics on all of the + processors in the system, This setting only temporarily overrides the + setting of “disabled”, “staggered” or + “periodic” and the platform will revert to the last setting + of “disabled”, “staggered” or + “periodic” once the immediately run diagnostics are + complete. + + + + + + + + Implementation Notes: To prevent conflicts in the + setting of the run-mode, the platform should only support this parameter + for one partition in a running system. The options may also be set by the + platform. The last value set will take precedent over any previous + settings. +
+ +
+ Processor Module Information + + The Processor Module Information system parameter allows + transferring of certain processor module information from the platform to + the OS. The information in the parameter is global for the platform and + encompasses all resources on the platform, not just those available to + the partition, and the + ibm,get-system-parameter will never return a + Status of -9002 (Not Authorized). This parameter is + read-only. + + + + R1--1. + + For the LPAR option with the System Parameters + option: If the platform supports the Processor Module + Information system parameter, then it must provide the following + information in the parameter, and the information returned for every + partition must be the same, with all the resources of the platform + encompassed: + 2 byte binary number (N) of module types followed by N module + specifiers of the form: + 2 byte binary number (M) of sockets of this module type + 2 byte binary number (L) of chips per this module type + 2 byte binary number (K) of cores per chip in this module + type. + + + + + R1--2. + + For the LPAR option with the System Parameters + option: For the Processor Module Information system parameter, + the + ibm,get-system-parameter RTAS call must never return + a + Status of -9002 (Not Authorized), and the + ibm,set-system-parameter RTAS call must always return + a Status of -9002 (Setting not allowed/authorized). + + + + +
+ +
+ Cede Latency Settings Information + + The Cede Latency Settings Information system parameter informs the + OS of the maximum latency to wake up from the various platform supported + processor sleep states that it might employ for idle processors. The + information in the parameter is global for the platform and encompasses + all processors on the platform, and the + ibm,get-system-parameter will never return a + Status of -9002 (Not Authorized). This parameter is + read-only. As the architecture evolves, the number of fields per record + are likely to increase, calling software should be written to handle + fewer fields (should it find itself running on a platform supporting an + older version of the architecture) and ignore additional fields (should + it find itself running on a platform supporting a newer version of the + architecture). Due to partition migration, the support for the cede + latency setting system parameter, the number of supported cede latency + settings (and thus the number of reported records) and the number of + fields reported per record might change from call to call; calling + software should be written to handle this variability + + + + R1--1. + + For the PEM option with the System Parameters + option: If the platform supports the cede latency settings + information system parameter it must provide the following information in + the NULL terminated parameter string: + + + + The first byte is the binary length “N” of each cede + latency setting record minus one (zero indicates a length of 1 + byte) + + + + For each supported cede latency setting a cede latency setting + record consisting of: The first “N” bytes of + . + + + + + Byte definitions within a cede latency setting + record + + + + + + + + + + Order of fields within a + record + + + + + Field Length + + + + + Values + + + + + Comments + + + + + + + + Cede Latency Specifier Value + + + 1 + + + Binary Values 0-255 + + + Records in ascending cede latency specifier value order + with no holes. + + + + + Maximum wakeup latency in time base ticks + + + 8 + + + 0x0000000000000000 - 0xFFFFFFFFFFFFFFFF + + +   + + + + + Responsive to external interrupts + + + 1 + + + Binary True/False + + +   + + + + +
+ + + + + R1--2. + + For the PEM option with the System Parameters + option: For the cede latency specifier system parameter, the + ibm,get-system-parameter RTAS call must never return + a + Status of -9002 (Not Authorized), and the + ibm,set-system-parameter RTAS call must always return + a + Status of -9002 (Setting not + allowed/authorized). + + + + +
+ +
+ Target Active Memory Compression Factor + + The target active memory compression factor system parameter + informs the OS of the target memory capacity increase the customer + expects to achieve due to active memory compression. The factor is + expressed in whole percentage with the minimum value of 100 and the + maximum value of 1000. + The + ibm,get-system-parameter for parameter token 46 will + never return a + Status of -9002 (Not Authorized). This parameter is + read-only. + + + + R1--1. + + For the Active Memory Compression option with the System + Parameters option: For the Target Active Memory Compression + Factor system parameter, the + ibm,get-system-parameter RTAS call must never return + a Status of -9002 (Not Authorized). + + + + + R1--2. + + For the Active Memory Compression option with the System + Parameters option: If the Active Memory Compression option is + enabled for the partition, the platform must provide in response to the + ibm,get-system-parameter for parameter token 46 the + two byte target active memory compression factor in binary format in the + range (0x0064 -- 0x03E8) (equivalent to 100 -- 1000 decimal). + + + + + R1--3. + + For the Active Memory Compression option with the System + Parameters option: If the Active Memory Compression option is + disabled for the system/partition, the platform must provide in response + to the + ibm,get-system-parameter for parameter token 46 the + two byte value 0x0000. + + + + + R1--4. + + For the Active Memory Compression option with the System + Parameters option: For the target active memory compression + factor system parameter, the + ibm,set-system-parameter RTAS call must always return + a Status of -9002 (Setting not allowed/authorized). + + + + +
+ +
+ Performance Boost Modes Vector + + A variety of platform dependent configuration modes might result in + a boost in platform computational capacity. The + ibm,get-system-parameter through the performance + boost modes vector system parameter communicates to the client program + which of these modes are available on the specific platform, which of + these modes the client program may enable/disable, and which ones are + active. + The performance boost mode vectors are 32 bytes (256 bits) long. + Each bit position within the performance boost mode vector corresponds to + a specific function as specified in + . The first defined boost mode + is assigned to the highest order bit position. As new boost modes are + defined, they are assigned to sequential lower order vector bit + positions. + Given that the second version of the vector from the + ibm,get-system-parameter RTAS call (specifying which + modes may be enabled/disabled by the client program) is non-zero, the + platform supports calling the + ibm,set-system-parameter RTAS call specifying the + performance boost modes vector token. The + ibm,set-system-parameter RTAS call specifying the + performance boost modes vector token takes a single vector as + input. + + + Performance Boost Modes Vector Bits + Definitions + + + + + + + + Bit Position (1 based + ordinal) + + + + + Definition + + + + + + + + 1 + + + Extended Cache Option + + + + + 2-- 256 + + + Reserved + + + + +
+ + + + R1--1. + + For the Performance Boost Modes option: The platform + must implement the System Parameters option. + + + + + R1--2. + + For the Performance Boost Modes option: The 96 byte + report returned by + ibm,get-system-parameter for parameter token 47 must + consist of three 32 byte bit vectors as defined by + . + + + + + R1--3. + + For the Performance Boost Modes option: The first 32 + byte bit vector returned by + ibm,get-system-parameter for parameter token 47 must + contain 1s in the bit positions define by + for the performance boost modes + that are both supported by the platform and authorized for the caller (by + means outside of the scope of LoPAR). + + + + + R1--4. + + For the Performance Boost Modes option: The second 32 + byte bit vector returned by + ibm,get-system-parameter for parameter token 47 must + contain 1s in the bit positions define by + for the performance boost modes + that are both represented in the first vector and may be enabled/disabled + by the caller through the + ibm,set-system-parameter using parameter token + 47. + + + + + R1--5. + + For the Performance Boost Modes option: The third 32 + byte bit vector returned by + ibm,get-system-parameter for parameter token 47 must + contain 1s in the bit positions define by + for the performance boost modes + that are both represented in the first vector and are enabled either by + default or by the caller through the + ibm,set-system-parameter using parameter token + 47. + + + + + R1--6. + + For the Performance Boost Modes option: If the + ibm,get-system-parameter for parameter token 47 + communicated that the client program has the ability to enable/disable + one or more of the boost modes, then the platform must support the + performance boost modes vector token for ibm,set-system-parameter. + + + + + R1--7. + + For the Performance Boost Modes option: If no boost + modes can be enabled/disabled then a call to ibm,set-system-parameter + specifying the boost modes vector token must return either: + + + + “System parameter not supported” as indeed the + implementation need not code support for the token if no mode setting is + supported. + + + + “Setting not allowed/authorized” if the + implementation supports setting boost modes but the caller is not + authorized to do so. + + + + + + + R1--8. + + For the Performance Boost Modes option: If any input + vector to the + ibm,set-system-parameter RTAS for parameter token 47 + is a one and does not correspond to a bit that is a one in the second + version of the vector returned by the + ibm,get-system-parameter RTAS for parameter token 47 + the ibm,set-system-parameter RTAS must return parameter error. + + + + + R1--9. + + For the Performance Boost Modes option: If the + corresponding bit that was a one in the second version of the vector + returned by the + ibm,get-system-parameter RTAS for parameter token 47 + is a one in the input vector to the + ibm,set-system-parameter RTAS for parameter token 47 + then upon successful return that corresponding boost mode must be + enabled. + + + + + R1--10. + + For the Performance Boost Modes option: If the + corresponding bit that was a one in the second version of the vector + returned by the + ibm,get-system-parameter RTAS for parameter token 47 + is a zero in the input vector to the + ibm,set-system-parameter RTAS for parameter token 47 + then upon successful return that corresponding boost mode must be + disabled. + + + + + R1--11. + + For the Performance Boost Modes option: To properly + awake from partition suspension and handle dynamic reconfiguration, the + client program must be prepared to handle changes in the bit settings + within the bit vectors reported by the + ibm,get-system-parameter RTAS for parameter token + 47. + + + + + R1--12. + + For the Performance Boost Modes option: Since it is + expected that bit positions define by + will expand over time, to avoid + firmware level compatibility issues, the client program must ignore bit + settings within the bit vectors reported by the + ibm,get-system-parameter RTAS for parameter token 47 + beyond those defined when the client pr gram was designed. + + + + +
+ +
+ Universally Unique IDentifier + + The Universally Unique IDentifier (UUID) option provides each + partition with a Universally Unique Identifier that is persisted by the + platform across partition reboots, reconfigurations, OS reinstalls, + partition migration, hibernation etc. The UUID is a 16 byte string of + format fields and random bits as defined in + . The random bits are generated + in an implementation dependent manner to achieve a projected probability + of collision of not greater than one in 2**60. + + + UUID Format + + + + + + + + + + Field + + + + + Byte:Bit + + + + + Size (Bits) + + + + + Values + + + + + + + + Version + + + 0:0 + + + 1 + + + 0: Initial Version + 1: Reserved + + + + + Random Bits + + + 0:1 thru 5:7 + + + 47 + + + Random Bits + + + + + Generation Method + + + 6:0-3 + + + 4 + + + 0b0000 Never Used + 0b0100 Random Generated + All other values are reserved + + + + + Random Bits + + + 6:4 - 7:7 + + + 12 + + + Random Bits + + + + + Variant + + + 8:0-1 + + + 2 + + + 0b10 DCE Variant UUID + All other values are reserved + + + + + Random Bits + + + 8:2 - 15:7 + + + 62 + + + Random Bits + + + + +
+ + + + R1--1. + + For the UUID option with the System Parameters + option: For the UUID system parameter, the + ibm,get-system-parameter RTAS call must never return + a Status of -9002 (Not Authorized). + + + + + R1--2. + + For the UUID option with the System Parameters + option: If the UUID option is enabled for the partition, the + platform must provide in response to the + ibm,getsystem-parameter for parameter token 48 the + calling partition unique 16 byte sting as described in + . + + + + + R1--3. + + For the UUID option with the System Parameters + option: If the UUID option is disabled for the + system/partition, the platform must provide in response to the + ibm,get-system-parameter for parameter token 48 the + two byte value 0x0000. + + + + + R1--4. + + For the UUID option with the System Parameters + option: For the UUID system parameter, the + ibm,set-system-parameter RTAS call must always return + a Status of -9002 (Setting not allowed/authorized). + + + + +
+ +
+ + + + diff --git a/RTAS/ch_rtas_environment.xml b/RTAS/ch_rtas_environment.xml new file mode 100644 index 0000000..aea5dc0 --- /dev/null +++ b/RTAS/ch_rtas_environment.xml @@ -0,0 +1,2560 @@ + + + + + Environment + + RTAS provides an interface definition between the OS and the firmware + provided by the platform. This chapter defines the calling conventions used + by both the OS and the platform’s RTAS firmware. + RTAS runs with instruction and data relocate as well as processing + exceptions disabled. To not interfere with the OS, RTAS may not cause any + exceptions, nor can it depend on any particular virtual memory + mappings. + All RTAS functions are invoked from the OS by calling the + rtas-call function. The address of this + function is obtained from OF when + RTAS is instantiated. See Requirement + for more details. RTAS determines + what function to invoke based on the data passed into the + rtas-call function. This section describes the + mechanisms used to invoke the rtas-call function, + the machine state, register usage, resource + allocation, and the invocation requirements. + If the LPAR option is enabled, multiple partitions may exist, each + with its own OS instance. This requires some changes to the RTAS + environment. These changes are discussed in + . + +
+ Machine State + When RTAS functions are invoked, the calling processor shall have + address translations, floating point, and most other exceptions disabled + and it shall be running in privileged state. + + + + R1--1. + + RTAS must be called in “real + mode,” that is, all address translation must be disabled. Bits MSRIR and + MSRDR of the MSR register must be zero. + + + + + R1--2. + + RTAS must be called in privileged mode, and + the MSRPR bit must be set to 0. + + + + + R1--3. + + RTAS must be called with external + interrupts disabled, and the MSREE bit must be set to 0. + + + + + R1--4. + + RTAS must be called with trace disabled, + and the MSRSE and + MSRBE bits must be set to 0. + + + + + R1--5. + + RTAS must be + called with floating point disabled, and the + MSRFE0, + MSRFE1, and + MSRFP bits must be set to 0. + + + + + R1--6. + + RTAS must be called with the MSRSF, + (MSRISF, and ASRV + bits if applicable on the specific processor) set + to match the mode used to instantiate RTAS (0 for + instantiate-rtas or 1 for + instantiate-rtas-64) and the + LE bit set to 0. + + + + + R1--7. + + With the exception of the MSRDR and + MSRRI bits, RTAS must not change the state of the + machine by modifying the MSR. + + + + + R1--8. + + rtas-call is entered + in a non-recoverable mode, indicated by having the + MSRRI bit set equal to 0, then RTAS must not enter a + recoverable mode by setting the MSRRI bit to 1. + + + + + R1--9. + + If called with MSRRI equal to 1, + then RTAS must protect its own + critical regions from recursion by setting the MSRRI + bit to 0 when in the critical regions. + + + + + Software Implementation Notes: + + + + If the MSRME bit is left enabled, the OS’s exception + handler must be aware that RTAS might have been running and that various + processor registers might not be in the expected state for an interrupted + OS, which precludes recoverability but permit logging machine + checks. + + + + There are some provisions for recursive calls to RTAS error + handling functions. Therefore, RTAS should set the MSRRI + bit to 0 if SRR0/SRR1 or any other RTAS resource + is in a state where information could be lost and prohibit + recovery. + + + + Requirement + implies that RTAS must be able + to be instantiated in 64-bit mode on platforms that can support 64-bit + execution. + + + +
+ +
+ Register Usage + + + + R1--1. + + Except as + required by a specific function, registers SPRG2, R0, R3 through R12, + CTR, XER, LR, and fields CR2-CR4 of the CR, RTAS must preserve all OS + visible register state. + + + + + R1--2. + + RTAS must not modify the DEC and registers SPRG0, SPRG1, and SPRG3. + + + + + Software Implementation Notes: + + + + RTAS is entered in real mode + (with address translation turned off). In this mode, all data accesses + are assumed to be cached in copy back mode with memory coherence + required. Since these settings may not be appropriate for all accesses, + RTAS is free to transparently use the processor specific facilities + required to access platform hardware resources. The OS machine check + handler can only depend on those registers that are required to be + unchanged (see Requirement + ). + + + + RTAS must not change the preserved registers, or must first save + them and restore the original contents before returning to the OS. + + + + The SRR0-SRR1, LR, CTR, XER registers, as well as any + reservations made via the load and reserve instructions, need not be + preserved. + + + +
+ +
+ RTAS Critical Regions + + The OS, when using RTAS, is responsible for protecting RTAS and + devices used by RTAS from any simultaneous accesses that could corrupt + memory or device registers. Such corruption could be caused by + simultaneous execution of RTAS code, or by a device driver accessing a + control register that is also modified by RTAS. In a single processor + system, since the MSREE bit is 0 when entering RTAS, a call to RTAS while + it is in execution is prevented except for the machine check handler. + This handler may need to call various RTAS services such as + check-exception or + system-reboot even if the error was detected while in + an RTAS service + . + The OS and RTAS must co-exist on the same platform. RTAS must not + change device registers that are used by the OS, nor may the OS change + device registers on devices used by RTAS. With the advent of more and + more integration into common super parts, some of these registers may + physically reside on the same component. In this section, device implies + the collection of common registers that together perform a function. Each + device must be represented in the OF device tree. + + + + R1--1. + + Except as noted in Requirement + and + , the OS must ensure that RTAS + is not called while RTAS is in execution and that RTAS is not + simultaneously called from different processors in a multi-processor + system. + + + + + R1--2. + + Any RTAS access to device or I/O registers + specified in this document must be made in such a way as to be + transparent to the OS. + + + + + R1--3. + + Any device that + is used to implement the RTAS abstracted services must have the property + “used-by-rtas” in the OF device tree. + However, if the device is only used by the + power-off, and + system-reboot calls, the property should not be set. + The + rtas-display-device must be marked with the property + “used-by-rtas” if it is a specialized + device only to be accessed via the RTAS + display-character call and not otherwise shared with + the OS + + + Software Implementation Note: + clarifies when a device should + be marked with the + “used-by-rtas” property, based on whether + it has any interaction with RTAS and/or the OS (with the exception of the + calls listed in Requirement + ). + + + Use of + <emphasis role="bold"><literal>“used-by-rtas”</literal></emphasis> + + + + + + + + +   + + + + + Normal Device (1) + + + + + rtas-display-device + + + + + + + + Only used by OS + + + not marked + + + N/A (2) + + + + + Only used by RTAS + + + marked + + + marked + + + + + OS and RTAS shared + + + marked (3) + + + not marked (4) + + + + + Virtual + + + N/A + + + N/A + + + + +
+ + + + A device which is not normally to be used by the OS must meet + one of the following rules. + + + + It must not be included in the OF device tree. + + + + It must be defined as a “reserved” device + node. + + + + It must be marked with the + “used-by-rtas” property in the OF device + tree. + + + + + + It is assumed that an + rtas-display-device is used by RTAS. + + + + It is assumed that there are no devices other than the + rtas-display-device which are used by both RTAS and + an “unaware” OS. To allow an aware OS to share a device with + RTAS, the device should be marked. + + + + It is assumed that the + rtas-display-device is used by both RTAS and the OS + (as coordinated by the OS via display-character) unless it is marked. See + also Requirement + . + + + + + + + + R1--4. + + Platforms must be designed such that + accesses to devices that are marked + “used-by-rtas” + have no side effects on other registers in the system. + + + + + R1--5. + + Any OS access to devices specified as + “used-by-rtas” + must be made in such a way as to be transparent to RTAS. + + + + + R1--6. + + RTAS must not generate any exceptions (for + example, no alignment exceptions, page table walk exceptions, + etc.). + + + + + R1--7. + + The OS machine check and soft reset handlers must be + able to call the RTAS services: + + + + nvram-fetch + + + + nvram-store + + + + check-exception + + + + display-character + + + + system-reboot + + + + set-power-level(0,0) + + + + power-off + + + + ibm,set-eeh-option + + + + ibm,set-slot-reset + + + + ibm,read-slot-reset-state2 + + + + + + + R1--8. + + The stop-self + service need only be serialized with calls to the + stop-self, + start-cpu, and + set-power-level services. The OS must be able to call + RTAS services on other processors while a processor is stopped or being + stopped. + + + + + Software Implementation Notes: + + + + While RTAS must not generate any exceptions, it is still + possible that a machine check interrupt may occur during the execution of + an RTAS function. In this case, the machine check handler may be entered + prior to the normal termination of the RTAS function. + + + + It is permissible for the OS exception handler to make an RTAS + call as long as Requirements + and + are met. In particular, it is + expected that the RTAS + check-exception is called from the OS exception + handler. + + + +
+ +
+ Resource Allocation and Use + During execution, RTAS requires memory for both code and data. This + memory may be in RAM, in a private memory area only known by the system + firmware, or in memory allocated by the OS for RTAS use. RTAS should use + this memory for its stack and any state savings. This memory is + subsequently called the “RTAS private data area.” + + + + R1--1. + + The OS must allocate + “rtas-size” + bytes of contiguous real memory as RTAS + private + data area. This memory must be aligned on a 4096 byte boundary and may + not cross a 256 MB boundary. + + + + + R1--2. + + The RTAS private data area must not be accessed by the OS. + + + + + R1--3. + + Except for the RTAS private data area, the + argument buffer, System Memory pointed to by any reference parameter in + the argument buffer, and any other System Memory areas explicitly + permitted in this chapter, RTAS must not modify any System Memory. RTAS + may, however, modify System Memory during error recovery provided that + such modifications are transparent to the OS. + + + + + R1--4. + + RTAS calls may + not sleep in any fashion nor busy wait for more than a very short period + of time, except for + power-off, ibm,power-off-ups, set-power-level (0,0), + system-reboot, ibm,update-flash-64-and-reboot, and + ibm,os-term. + + Software + Implementation Note: An RTAS call should take the same amount of time to + perform a service that it would take the OS to perform the same function. + A specific goal is that RTAS primitives should take less than a few tens + of microseconds. + + + + + R1--5. + + For RTAS calls which do not allow the + Status of -2 (Busy), there may be “rare” + instances where an anomaly may occur and the call may take longer than a + “very short period of time.” In these cases, the call must + complete within 250 microseconds. Otherwise, a hardware error response + must be given. + + + + +
+ +
+ Instantiating RTAS + RTAS is instantiated by an explicit client interface service call + into OF. The OF device tree contains a property + (“rtas-size”, under + the + /rtas node) which defines how much real memory RTAS + requires from the OS. The OS allocates + “rtas-size” + bytes of real memory, and + then invokes the + instantiate-rtas or + instantiate-rtas-64 method of the + /rtas node, passing the real address of the private + data area (or zero, if + “rtas-size” is zero) as the + rtas-base-address input argument. Firmware binds RTAS + to that address, binds the addresses of devices that RTAS uses, performs + any RTAS initialization, and returns the address of the + rtas-call + function + that is appropriate. + + + + R1--1. + + The instantiate-rtas or + instantiate-rtas-64 + OF method + must have the arguments specified in + . + + + <emphasis role="bold"><literal>instantiate-rtas</literal></emphasis> + <emphasis role="bold"><literal>instantiate-rtas-64</literal></emphasis> + Argument Call Buffer + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + rtas-base-address + + + + Real Address of RTAS area or zero, if + “rtas-size” is zero + + + + + Out + + + + rtas-call + + + + Real address used to invoke RTAS functions + + + + +
+ + + + + R1--2. + + The RTAS code bound and initialized by the + instantiate-rtas method on a 64-bit capable platform, + must be able to handle platform resources that are accessed using 64-bit + addresses. + + + + +
+ +
+ RTAS Device Tree Properties + The OF device tree contains a + /rtas device node that describes the implemented RTAS + features and the output device supported by RTAS. Within this device node + are properties that describe the RTAS functions implemented by the + firmware. For every implemented RTAS function, the + /rtas node contains an OF property whose name is the + same as the RTAS function. The value of this property is the token + argument passed into the + rtas-call + function + when making that specific RTAS call. Note that some + RTAS functions are optional and some are required. This is defined in + . + + + + R1--1. + + The OF device tree must contain a device + node named + /rtas which describes the RTAS implementation. + + + + + R1--2. + + The /rtas device node must have a property for each + implemented RTAS function in + . The value of this property is + a token that is passed into the + rtas-call + function to + indicate which RTAS function to invoke. + + RTAS Tokens for Functions + + + + + + + + + RTAS property/function + + + + + Required? + + + + + Notes + + + + + + + + + “nvram-fetch” + + + + + + + Required + + + Execution time proportional to amount of data + + + + + + “nvram-store” + + + + + + + Required + + + Execution time proportional to amount of data + + + + + + “get-time-of-day” + + + + + + + Required + + +   + + + + + + “set-time-of-day” + + + + + + + Required + + +   + + + + + + “set-time-for-power-on” + + + + + + +   + + +   + + + + + + “event-scan” + + + + + + + Required + + +   + + + + + + “check-exception” + + + + + + + Required + + +   + + + + + + “rtas-last-error” + + + + + + + Required + + +   + + + + + + “ibm,platform-dump” + + + + + + + If the Platform Dump option is implemented + + +   + + + + + + “ibm,read-pci-config” + + + + + + + Required + + +   + + + + + + “ibm,write-pci-config” + + + + + + + + + + “display-character” + + + + + + +   + + +   + + + + + + “set-indicator” + + + + + + + Required + + + Some specific indicators are required, and some are + optional + + + + + + “get-sensor-state” + + + + + + +   + + +   + + + + + + “ibm,set-system-parameter” + + + + + + +   + + +   + + + + + + “ibm,get-system-parameter” + + + + + + +   + + +   + + + + + + “set-power-level” + + + + + + + Required for DR operations (see + ) + + +   + + + + + + “get-power-level” + + + + + + +   + + + + + + “power-off” + + + + + + +   + + + Provided for platforms with software controlled power off + capability + + + + + + “ibm,power-off-ups” + + + + + + + If there may be a platform controlled UPS. + + + For power off control in a platform which may have power + backed up with an Uninterruptible Power Supply (UPS). + + + + + + “system-reboot” + + + + + + + Required + + +   + + + + + + “ibm,update-flash-64-and-reboot” + + + + + + +   + + +   + + + + + + “ibm,manage-flash-image” + + + + + + +   + + +   + + + + + + “ibm,validate-flash-image” + + + + + + +   + + +   + + + + + + “ibm,activate-firmware” + + + + + + +   + + +   + + + + + + “stop-self” + + + + + + + See Note + + +   + + + + + + “start-cpu” + + + + + + +   + + + + + + “query-cpu-stopped-state” + + + + + + +   + + + + + + “ibm,os-term” + + + + + + +   + + +   + + + + + + “ibm,exti2c” + + + + + + +   + + +   + + + + + + “ibm,get-xive” + + + + + + + Required for the PowerPC External Interrupt option + + +   + + + + + + “ibm,set-xive” + + + + + + +   + + + + + + “ibm,int-off” + + + + + + +   + + + + + + “ibm,int-on” + + + + + + +   + + + + + + “ibm,configure-connector” + + + + + + + Required for all DR options + + + See + . + + + + + + “ibm,set-eeh-option” + + + + + + + Required for EEH option + + +   + + + + + + “ibm,set-slot-reset” + + + + + + +   + + + + + + “ibm,read-slot-reset-state” + + + + Being replaced by + + ibm,read-slot-reset-state2 + + + + See + . + + + + + + “ibm,read-slot-reset-state2” + + + + + + + Required for all platforms + + +   + + + + + + “ibm,get-config-addr-info2” + + + + + + + Required on all platforms + + +   + + + + + + “ibm,slot-error-detail” + + + + + + + Required for the EEH option + + +   + + + + + + “ibm,open-errinjct” + + + + + + + Required for ERRINJCT option + + +   + + + + + + “ibm,errinjct” + + + + + + +   + + + + + + “ibm,close-errinjct” + + + + + + +   + + + + + + “ibm,nmi-register” + + + + + + + Required for FWNMI option + + +   + + + + + + “ibm,nmi-interlock” + + + + + + +   + + + + + + “ibm,configure-bridge” + + + + + + + Required for the EEH option + + +   + + + + + + “ibm,configure-pe” + + + + + + + Required for the EEH option + + +   + + + + + + “ibm,get-indices” + + + + + + + Sometimes (see + ) + + +   + + + + + + “ibm,get-vpd” + + + + + + + Required for the Dynamic VPD option + + +   + + + + + + “ibm,manage-storage-preservation” + + + + + + + Required for the Storage Preservation option + + +   + + + + + + “ibm,get-dynamic-sensor-state” + + + + + + + See Requirement + . + + +   + + + + + + “ibm,set-dynamic-indicator” + + + + + + + See Requirement + . + + +   + + + + + + “ibm,change-msi” + + + + + + + Required for the MSI option. Required if any PCI Express + HB in the platform. + + +   + + + + + + “ibm,suspend-me” + + + + + + + Required for the Partition Suspension option + + +   + + + + + + “ibm,update-nodes” + + + + + + + Required for the Update OF Tree option + + +   + + + + + + “ibm,update-properties” + + + + + + + Required for the Update OF Tree option + + +   + + + + + + “ibm,configure-kernel-dump” + + + + + + + Required for the Configure Platform Assisted Kernel Dump + option + + +   + + + + + + “ibm,query-pe-dma-window” + + + + + + + Required for the Dynamic DMA Window (DDW) option + + +   + + + + + + “ibm,create-pe-dma-window” + + + + + + +   + + + + + + “ibm,remove-pe-dma-window” + + + + + + +   + + + + + + “ibm,reset-pe-dma-windows” + + + + + + + Required for the LoPAR version l of the Dynamic DMA + Window (DDW) option + + +   + + + + +
+ + Note: These commands are required in SMP platforms if + dynamic reconfiguration is required of the processors. Similarly, a + degraded mode may need these, or similar commands in the case of + detection of excessive errors. In the case of a processor deconfigured by + dynamic reconfiguration or due to excessive errors, the returned + CPU_status from the + query-cpu-stopped-state RTAS call is 2 (The processor + thread is not in the RTAS stopped state) since the deconfigured processor + cannot be started. + + + + + R1--3. + + The OF properties listed in + must be in the + /rtas device tree node prior to booting the + OS. + + + OF Device Tree Properties + + + + + + + + name + + + + + value + + + + + + + + + “rtas-size” + + + + integer size of RTAS private data area or zero if + allocation is not required + + + + + + “rtas-version” + + + + An integer encoding of the RTAS interface version. This + document describes version 1. + + + + + + “rtas-event-scan-rate” + + + + The rate, in calls per minute, at which rtas-event-scan + should be called by the OS. See + . + + + + + + “rtas-display-device” + + + + The + phandle of the device node used by the RTAS + call, + display-character. + + + + + + “rtas-error-log-max” + + + + The maximum size of an extended error log. + + + + +
+ + + + + R1--4. + + All RTAS functions listed as + “Required” in + must be implemented in + RTAS. + + + + + R1--5. + + For the Symmetric Multiprocessor option: The + functions listed as “Required in SMP Platforms” in + must be implemented in + RTAS. + + + + + Software Implementation Notes: + + + + It is permitted for RTAS not to implement those optional + functions that are not appropriate or not needed on a particular + platform. + + + + Vendors may introduce private RTAS calls of their own. If they + do, the property names should be of the form + “vendor,property” where + vendor is a company name string as defined by OF. + Future versions of this architecture will not choose RTAS property names + that include a comma. + + + +
+ RTAS Device Tree Properties for Indicators and + Sensors + Indicators and sensors may be static or dynamic. Each indicator or + sensor type is identified by its token; a number which is associated with + the functionality of the indicator or sensor. A specific indicator token + is static in a particular platform if the number of indicators of that + type do not change with Dynamic Reconfiguration (DR) operations, and + dynamic otherwise. Certain sensors and indicators associated with DR + + DR indicators include isolation-state (9001), DR indicator + (9002), and allocation-state (9003). DR sensors include dr-entity-sense + (9003). DR indicators and sensors are required to be there based on the + DR entity being supported. Their indices are specified by the DR index + for the DR entity. See + and + for more information. + are static since they represent the base hardware, others are + dynamic coming and going with extensions to the base hardware. Indices + for DR indicators and sensors are obtained from the DRC index for the DRC + connector. Information about static non-DR indicators and sensors (like + indices and location codes) are specified in the OF device tree at boot + time and do not change. Information about non-DR dynamic indicators and + sensors, needs to be gathered via the + ibm,get-indices RTAS call (see + ), and sensors, instead of + being represented in the device tree. + Indicators and sensors within a platform generally have location + codes associated with them. Location code information for static + indicators and sensors, except DR indicators and sensors, are placed in + the + “<vendor>,indicator-<token>” and + “<vendor>,sensor-<token>” + properties, respectively, in the + /rtas node, where “<vendor>” is + defined in the column marked “<vendor>” in + and + , respectively. Location code + information for dynamic indicators and sensors, except DR indicators and + sensors, for the most part come in via the + ibm,get-indices call. + Information (index, location code) about a particular indicator or + sensor token, except DR indicators and sensors, are in the + /rtas node properties or are available via the + ibm,get-indices call, but not both. When indices are + provided via the + “rtas-sensors” or + “rtas-indicators” properties, it is + expected that there exists a sensor/indicator for each index between 0 + and + maxindex. When indices are provided via the + ibm,get-indices call, the indices may not be + contiguous, and any of the indices between 0 and + maxindex may be missing. + The formats for location codes are defined in + . For indicators and sensors, + these location codes are for the location of the device being manipulated + or measured, not the location of the specific controller or sensor. The + location code for an abstracted indicator or sensor is a NULL + string. + +
+ Indicators + For static indicators, except DR indicators, OF provides for paired + integers ( + token maxindex) for each indicator token under the + property + “rtas-indicators” + in the + /rtas node. With this information, the OS can + determine which types of indicators, and the maximum number ( + maxindex) of each type, that the platform + provides. + For static indicators, except DR indicators, the extension + property, + “<vendor>,indicator-<token>” + (see ), provides an array of strings + containing the FRU location codes associated with each indicator. See + . Here, “ + <vendor>” corresponds to the + “<vendor>” column of + + + and “ + <token>” corresponds to the token of the + + “rtas-indicators” + type. + The index of a specific indicator token is used to index into the array + up to + maxindex. + Indices and location codes for dynamic indicators are obtained via + the + ibm,get-indices RTAS call and do not appear in the + static properties in the + /rtas node. + Indices for DR indicators 9001, 9002, and 9003 are obtained from + the DRC index for the DRC connector. See Requirement + . + + + + R1--1. + + For all static + indicators, except DR indicators 9001, 9002, and 9003, OF must provide + the extension property, + “<vendor>,indicator-<token>”, + in the + /rtas node, unless the indicator is part of an + extension which has its own set of appropriate properties for the + indicator, where “ + <vendor>” must be as defined in the + column labeled “<vendor>” in + for the specific indicator + token value. + + + + + R1--2. + + For all static indicators for which + there is an associated + “<vendor>,indicator-<token>” + property and for which there is not a + physical realization, the location code string must be NULL. + + + + + R1--3. + + Indices and location codes for any + indicator token, except DR indicators 9001, 9002, and 9003, for which the + number of such indicators in the platform may change dynamically, must be + obtained via the + ibm,get-indices RTAS call and the indicator token + must not appear in the + “<vendor>,indicator-<token>” + or “rtas-indicators” in the + /rtas node. + + + + + R1--4. + + The indicator token of 4 must not exist + in a platform when a Error Log (token 9006) is implemented. + + + + +
+ +
+ Sensors + For static sensors, except DR sensors, OF currently provides for + paired integers ( + token maxindex) for each sensor token under the + property + “rtas-sensors” + in the + /rtas node. With this information, the OS can + determine which types of sensors, and how many of each type, that the + platform provides. + For static sensors, except DR sensors, the extension property, + “<vendor>,sensor-<token>” + (see ), provides an array of strings + containing the FRU location codes associated with each sensor. See + . Here, “ + <vendor>” corresponds to the + “<vendor>” column of + + + and “ + <token>” corresponds to the token in the + + “rtas-sensors” property. The index of a + specific sensor is used to index into the array up to + maxindex. + Indices and location codes for dynamic sensors, except DR sensors, + are obtained via the + ibm,get-indices RTAS call and do not appear in the + static properties in the + /rtas node. + Indices for DR sensors 9003 are obtained from the DRC index for the + DRC connector. See Requirement + . + + + + R1--1. + + For all static + sensors, except DR sensor 9003, OF must provide the extension property, + “<vendor>,sensor-<token>”, in the + /rtas node, unless the sensor is part of an extension + which has its own set of appropriate properties for the sensor, where + “ + <vendor>” must be as defined in the + column labeled “<vendor>” in + for the specific sensor token + value. + + + + + R1--2. + + For all static sensors for which there + is an associated + “<vendor>,sensor-<token>” + property and for which there is not a + physical realization, the location code string must be NULL. + + + + + R1--3. + + Indices and location codes for any + sensor token, except DR sensor 9003, for which the number of such sensors + in the platform may change dynamically, must be obtained via the + ibm,get-indices RTAS call and the sensor token must + not appear in the + “<vendor>,sensor-<token>” + or “rtas-sensors” in the + /rtas node. + + + + + R1--4. + + The following sensor tokens must not be + implemented if the number of them may be changed by a DR operation (that + is, they can only be used when static): 3, 9001, and 9002. + + + + +
+ +
+ +
+ +
+ Calling Mechanism and Conventions + + RTAS is + called through a mechanism similar to the OF client interface service. An + argument buffer is constructed which describes the desired RTAS call. + This description includes an indication of the RTAS call that is being + invoked, the number and value of the input parameters, the number of + result values, and space for each of the result values. + + + + R1--1. + + In order to make an RTAS call, the OS must + construct an argument call buffer aligned on an eight byte boundary in + physically contiguous real memory as described by + . + + + RTAS Argument Call Buffer + + + + + + + + Cell Number + + + + + Use + + + + + + + + 1 + + + Token Specifying which RTAS Call + + + + + 2 + + + Number of Input Parameters + + + + + 3 + + + Number of Output Parameters + + + + + 4 + + + First Input Parameter + + + + + ... + + + + Other Input Parameters + + + + + 4 + Number of Inputs -1 + + + Last Input Parameter + + + + + 4 + Number of Inputs + + + First Output Parameter + + + + + ... + + + + Other Output Parameters + + + + + 4 + Number of Inputs + + Number of Outputs -1 + + + Last Output Parameter + + + + +
+ + + + + R1--2. + + If the system is + a 32-bit system, or if RTAS was instantiated by + instantiate-rtas, then all + cells in + the RTAS argument buffer must be 32-bit sign extended values that are + aligned to 4 byte boundaries. + + + + + R1--3. + + If the system is + a 64 bit system and if RTAS was instantiated by + instantiate-rtas-64, then all + cells in the RTAS argument buffer must be 64-bit sign extended values + that are aligned to 8 byte boundaries. + + + + + R1--4. + + RTAS functions must be invoked by branching + to the + rtas-call address which is returned by the + + instantiate-rtas + or + + instantiate-rtas-64 + OF method (see + ). + + + + + R1--5. + + Register R3 must contain the argument + buffer’s real address when + rtas-call is invoked. + + + + + R1--6. + + Register R4 must contain the real address + of the RTAS private data area when + rtas-call is invoked (see Requirement + ). + + + + + R1--7. + + The Link Register must contain the return + address when + rtas-call is invoked. + + + + + Software Implementation Notes: + + + + RTAS is not required to perform sanity checking of its input + parameters. Using invalid values for any parameter in an RTAS argument + buffer gives undefined results. However, when such checks are made, the + appropriate return code for invalid parameters is -3. + + + + The token that specifies the RTAS call is obtained by looking up + the desired call from the + /rtas node of the OF device tree. + + + + The OS must be aware that the effective address range for RTAS + is 4 GB when instantiated in 32-bit mode and the OS should not pass RTAS + addresses or blocks of data which might fall outside of this + range. + + + +
+ +
+ Return Codes + + + + R1--1. + + The first output + value of all the RTAS functions must be a + Status word which denotes the result of the call. The + + Status word takes on one of the values in + . Non-negative values indicate + success. + + + RTAS + <emphasis>Status</emphasis> Word Values + + + + + + + + Values + + + + + + Status Word Meanings + + + + + + + + 0 + + + RTAS function call succeeded. + + + + + -1 + + + RTAS function call encountered a hardware error. + + + + + -2 + + + A necessary hardware device was busy, and the requested + function could not be performed. The operation should be + retried at a later time. + + + + + -3 + + + Parameter Error. + In some cases, specific parameter errors are enumerated. + However, other parameter errors may be reported using this + return code in addition to those enumerated. + + + + + -7 + + + Unexpected state change. + + + + + 9000-9899 + + + Reserved for vendor specific success codes. + + + + + 990x + + + Extended delay - where x is a number in the range of + 0-5 + + + + + -9000 + + + Multi-level isolation error (see + ). + + + + + -9004 - (-9999) + + + Reserved for vendor specific error codes. + + + + + Additional Negative Numbers + + + An error was encountered. The meaning of this error is + specific to the RTAS function that was invoked. + + + + + Additional Positive Numbers + + + The function succeeded. The meaning of the + Status word is specific to the RTAS + function that was invoked. + + + + +
+ + + + + + indicates a summation of all + possible + Status word values. A given RTAS function cannot + yield all of the possible + Status words. For the specific + Status words which apply to a specific RTAS function, + see the semantics for that function. + Software Implementation Notes: + + + + A return code of -2 or 990x may either mean that the operation + was initiated but not completed, or may mean that the operation was not + initiated at all. + + + + When the extended delay (990x) is returned, it is suggested that + software delay for 10 raised to the x milliseconds, where x is the last + digit of the 990x return code, before calling the function again. + + + +
+ + + diff --git a/RTAS/ch_rtas_introduction.xml b/RTAS/ch_rtas_introduction.xml new file mode 100644 index 0000000..c93e06a --- /dev/null +++ b/RTAS/ch_rtas_introduction.xml @@ -0,0 +1,76 @@ + + + + + Introduction + + The Run-Time Abstraction Service (RTAS) functions are provided by + LoPAR platforms to insulate the OS from having to know about and + manipulate a number of key platform hardware functions which ordinarily + require platform-dependent code. The OS calls RTAS functions rather than + manipulating hardware registers directly, reducing the need for platform + tailoring by the OS. This method of abstracting access to these platform + functions also permits hardware designers considerable flexibility in + hardware implementation. Since RTAS is provided by the platform developer, + this approach places the responsibility for supporting the platform + hardware design with the platform developer, not the OS developer. This + permits a degree of independence between the schedules of hardware and + software and reduces the release and test requirements for the OS, since it + can be tested to conform to the RTAS interface and not to every specific + hardware implementation. See + + for a list of all RTAS calls, and + which ones are required based on which LoPAR options that are implemented + in the platform. + + In order for platforms to achieve this separation of OS code from + hardware implementation dependencies, RTAS defines an interface between the + platform and the OS that provides control of some of the common devices + found on all platforms. RTAS is a system programming interface that is + realized, on a specific platform, by an RTAS implementation. The RTAS + implementation provides the platform specific processing of the common + components. RTAS limits itself to the run-time control of non-I/O, + typically system board-resident, hardware features. Traditionally, features + such as these have been implemented differently on different platforms. The + different implementations have required much effort and platform-dependent + code in the OS. RTAS permits the OS to operate over a much wider range of + platforms without specialized code for each platform. + + In general, the OS should not access RTAS resources directly. It + should call RTAS to control the resource. + + OS drivers are necessary to provide device specific processing for + IOAs. + + The role of RTAS versus OF is very important to understand. OF and + RTAS are both platform-specific software, and both are tailored by the + platform developer to manipulate the specific platform hardware. However, + RTAS is intended to be present during the execution of the OS, and to be + called by the OS to access platform hardware features on behalf of the OS, + whereas OF need not be present when the OS is running. This frees + OF’s memory to be used by applications. RTAS is small enough to + painlessly coexist with the OS and applications. + + This document uses the term RTAS to refer both to the architected RTAS + interface and to an RTAS implementation. + + diff --git a/RTAS/pom.xml b/RTAS/pom.xml new file mode 100644 index 0000000..d9775dd --- /dev/null +++ b/RTAS/pom.xml @@ -0,0 +1,148 @@ + + + + + org.openpowerfoundation.docs + workgroup-pom + 1.0.0-SNAPSHOT + ../pom.xml + + 4.0.0 + + + LoPAR-RTAS + + jar + + + LoPAR-RTAS + + + + + 0 + + + + + + + + + org.openpowerfoundation.docs + + openpowerdocs-maven-plugin + + + + generate-webhelp + + generate-webhelp + + generate-sources + + + ${comments.enabled} + LoPAR-RTAS + 1 + UA-17511903-1 + + appendix toc,title + article/appendix nop + article toc,title + book toc,title,figure,table,example,equation + book/appendix nop + book/chapter nop + chapter toc,title + chapter/section nop + section toc + part toc,title + qandadiv toc + qandaset toc + reference toc,title + set toc,title + + + 1 + 3 + 1 + + + LoPAR_RTAS + + + LoPAR_RTAS + + + + workgroupSpecification + + + + + workgroupConfidential + + + + + draft + + + + + + + + + true + . + + + bk_main.xml + + + + + ${basedir}/../glossary/glossary-terms.xml + 1 + www.openpowerfoundation.org + + + + + + diff --git a/RTAS/sec_rtas_get_indices.xml b/RTAS/sec_rtas_get_indices.xml new file mode 100644 index 0000000..fdbe42c --- /dev/null +++ b/RTAS/sec_rtas_get_indices.xml @@ -0,0 +1,5952 @@ + + +
+ + <emphasis>ibm,get-indices</emphasis> Call + + The RTAS function + ibm,get-indices is used to obtain the indices and + location codes for a specified indicator or sensor token. It allows for + obtaining the list of indicators and sensors dynamically and therefore + assists in any Dynamic Reconfiguration operation that involves indicators + and sensors being added or deleted from the platform (unlike the + /rtas node + “<vendor>,indicator-<token>”, + “<vendor>,sensor-<token>”, + and “ibm,environmental-sensor” properties). + This call also allows discontiguous indices for a particular indicator or + sensor type (unlike the + “rtas-indicators”, + “rtas-sensors”, and + + “ibm,environmental-sensor” properties). + This RTAS call is not used for DR indicators (9001, 9002, and 9003) + or DR sensors (9003). See the following sections in the DR chapter for more + information: + and + . + It may require several calls to the + ibm,get-indices RTAS routine to get the entire list of + indicators or sensors of a particular type. Each call may specify a + different work area. + The OS may not interleave calls to + ibm,get-indices for different indicator or sensor + types. Other standard RTAS locking rules apply. + + + + R1--1. + + For all DR options: The RTAS function + ibm,get-indices must implement the argument call buffer + defined by + . + + + Argument Call Buffer + <emphasis>ibm,get-indices</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,get-indices + + + + + + Number Inputs + + + + 5 + + + + + + Number Outputs + + + + 2 + + + + + + Indicator or Sensor + + + + 0: indicator of given type + 1: sensor of given type + + + + + + Indicator Type + + + + Indicator or sensor type (for example, 9006, 9007) + + + + + + Work Area Address + + + + Address of work area + + + + + + Work Area Size + + + + Size of work area + + + + + + Starting Number + + + + Integer representing first indicator number to + return + + + + + Out + + + + Status + + + + -1: Hardware error + -3: Indicator type not supported + -4: Optional: Indicator list changed, start again + 0: Success + 1: More data available; call again + 990x:Extended Delay where x is a number 0-5 (see text + below) + + + + + + Next Starting Number + + + + Integer to use as the Starting Number parameter on the next + call, or 1 if no more calls are required + + + + +
+ When the 990x + Status is returned, it is suggested that software delay + for 10 raised to the x milliseconds (where x is the last digit of the 990x + return code), before calling + ibm,get-indices with the same Starting Number and + Indicator Type. However, software may issue the + ibm,get-indices call again either earlier or later than + this. + + + + + R1--2. + + The OS must not interleave calls to + ibm,get-indices for different indicator or sensor + types. + + + + + R1--3. + + On the first call to get a particular + Indicator Type, the caller must provide a Starting + Number of 1 (32-bit integer) + + + + + R1--4. + + When + ibm,get-indices is called with a Starting Number of 1, + firmware must refresh any stale data in previously cached firmware buffers + for that indicator (for example, data made stale by a Dynamic + Reconfiguration operation). + + + + + R1--5. + + When calling + ibm,get-indices with a Starting Number of 1, a + previously returned + Next Starting Number value must be discarded. + + + + + R1--6. + + Optionally, if firmware detects a change in + the indicator list before the entire list is returned, the + ibm,get-indices call must return a -4 and the caller + must start again with a Starting Number of 1. + + + + + R1--7. + + The return data format in the work area for + all sensors and indicators must be as follows: + + + + Number Returned: 32-bit integer representing the number of + indicator indices returned on this call + + + + Sets of (32-bit integer index, 32-bit integer length of location + code including NULLs, location code string (NULL terminated and padded to + nearest 4 byte boundary)), one set per indicator or sensor, with the number + of sets indicated by the first integer in this work buffer + + + + + + + R1--8. + + If the + Status returned is 1 (more data available, call again), + then the caller must call + ibm,get-indices again with the + Starting Number parameter set to the Next Starting + Number integer from the previously returned buffer. + + + + + R1--9. + + The ibm,get-indices RTAS call must return the + Status value of -3 for the following conditions: + + + + Indicator type not supported + + + + No indicators of specified Indicator Type available to + caller + + + + + + + R1--10. + + If the ibm,get-indices RTAS call returns a + Status of anything other than 0 or 1 is returned, the + caller must consider that the contents of the work area is not + defined. + + + + + R1--11. + + The work area specified in the + ibm,get-indices RTAS call argument buffer must be + contiguous in logical real memory and must reside below 4GB. + + + + + R1--12. + + The ibm,get-indices RTAS call must only return the + indicator or sensor indices to which the caller has authorized access at + the time of the call. + + + + + R1--13. + + The ibm,get-indices RTAS call must make no assumptions + about the contents of the work area on the beginning of the call. + + + + + R1--14. + + When the platform supports the + ibm,get-indices RTAS call, the device tree must include + the + “ibm,get-indicator-indices-types” property + in the + /rtas node if the call is to be used for getting + indicator information and must include the + “ibm,get-sensor-indices-types” property in + the + /rtas node if the call is to be used for getting sensor + information. + + + + + R1--15. + + When an indicator token is provided in the + “ibm,get-indicator-indices-types” property, + it must not be included in the + “<vendor>,indicator-<token>” + property and must not be included in the + “rtas-indicators” property. + + + + + R1--16. + + When a sensor token is provided in the + “ibm,get-sensor-indices-types” property, it + must not be included in the + “<vendor>,sensor-<token>” + property and must not be included in the + “rtas-sensors” property. + + + + + R1--17. + + When an environmental sensor token is + provided in the + “ibm,get-sensor-indices-types” property, + users of data in the + “ibm,environmental-sensors” property for + that sensor token must not assume that the indices are contiguous for that + sensor token (that is, any of the indices between 0 and the maxindex, + inclusive, may be missing). + + + + + R1--18. + + When the value of + any index returned is 0xFFFFFFFF, the OS must use the + ibm,get-dynamic-sensor-state and + ibm,set-dynamic-indicator RTAS functions for this + sensor or indicator, using the location code to identify the sensor or + indicator. + + + + + R1--19. + + The OS must not call + get-sensor-state or + get-indicator with an index value of 0xFFFFFFFF. + + + + +
+ RTAS Call <emphasis>ibm,set-dynamic-indicator</emphasis> + + This RTAS call behaves as the RTAS + set-indicator call, except that the instance of the + indicator is identified by a location code instead of a index. + + + + R1--1. + + Platforms that + implement any indicators that are identified by location code instead of + index (see Requirement + ) must implement the + ibm,set-dynamic-indicator RTAS function. + + + + + R1--2. + + The RTAS function + ibm,set-dynamic-indicator must implement the argument + call buffer defined by + . + + + Argument Call Buffer + <emphasis>ibm,set-dynamic-indicator</emphasis> + + + + + + + + + Parameter Type + + + + + + Name + + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,set-dynamic-indicator + + + + + + Number Inputs + + + + 3 + + + + + + Number Outputs + + + + 1 + + + + + + Indicator + + + + Token defining the indicator + 9006: Error Log + 9007: Identify Indicator + + + + + + State + + + + Desired new state; see + . + + + + + + Location Code Address + + + + Real or Logical address of a location code string, in the + format defined by Requirement + + + + + + Out + + + + Status + + + + -1: Hardware error + -2: Busy, try again later + -3: No such indicator + 0: Success + 990x: Extended delay, where x is a number between 0 and + 5, as described below + + + + +
+ When 990x + Status is returned, it is suggested that software + delay for 10 raised to the power + x milliseconds (where + x is the last digit of the 990x return code), before + calling + ibm,set-dynamic-indicator with the same indicator + type and location code. However, software may call + ibm,set-dynamic-indicator again either earlier or + later than this. + + + + + R1--3. + + The OS must not call + ibm,set-dynamic-indicator with a different indicator + until a non-busy return + Status has been received from the previous + ibm,set-dynamic-indicator call. + + + + + R1--4. + + The location code string referenced by the + Location Code Address argument in the + ibm,set-dynamic-indicator argument call buffer must + reside in contiguous in real memory below an address of 4GB. + + + + + R1--5. + + The input data + format in the work area must be as follows: + + + + 32-bit integer length of the location code string, including + NULL + + + + Location code string, NULL terminated, identifying the sensor to + be set. + + + + + + + R1--6. + + The platform must not modify the location + code string. + + + + + R1--7. + + The OS must only use this call for + indicators which have been provided by the + ibm,get-indices RTAS call with an index value of + 0xFFFFFFFF. + + + + + R1--8. + + Platforms must identify all indicators + except types 9006 and 9007 by index. + + + + + R1--9. + + The ibm,set-dynamic-indicator RTAS call must return A + Status of -3 for the following conditions: + + + + Indicator type not supported + + + + The specified location code does not identify a valid + indicator + + + + + + +
+ +
+ RTAS Call <emphasis>ibm,get-dynamic-sensor-state</emphasis> + This RTAS call behaves as the RTAS + get-sensor-state call, except that the instance of + the sensor is identified by a location code instead of a index. + + + + R1--1. + + Platforms that + implement any sensors that are identified by location code instead of + index (see Requirement + ) must implement the + ibm,get-dynamic-sensor-state RTAS function. + + + + + R1--2. + + The RTAS function + ibm,get-dynamic-sensor-state must implement the + argument call buffer defined by + . +   + + Argument Call Buffer + <emphasis>ibm,get-dynamic-sensor-state</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,get-dynamic-sensor-state + + + + +   + + + + Number Inputs + + + + 2 + + + + +   + + + + Number Outputs + + + + 2 + + + + +   + + + + Sensor + + + + Token defining the sensor + + + + +   + + + + Location Code Address + + + + Real or Logical address of a location code string, in the + format defined by Requirement + + + + + + Out + + + + Status + + + + -1: Hardware error + -2: Busy, try again later + -3: No such indicator + 0: Success + 990x: Extended delay, where x is a number between 0 and + 5, as described below + + + + +   + + + + State + + + + Current state of the sensor as defined in the + Defined Values column of + . + + + + +
+ When 990x + Status is returned, it is suggested that software + delay for 10 raised to the power + x milliseconds (where + x is the last digit of the 990x return code), before + calling + ibm,get-dynamic-sensor-state with the same indicator + type and location code. However, software may call + ibm,get-dynamic-sensor-state again either earlier or + later than this. + + + + + R1--3. + + The OS must not call + ibm,get-dynamic-sensor-state with a different sensor + until a non-busy return + Status has been received from the previous + ibm,get-dynamic-sensor-state call. + + + + + R1--4. + + The work area must be contiguous in real + memory and must reside below 4GB. + + + + + R1--5. + + The input data + format in the work area must be as follows: + + + + 32-bit integer length of the location code string, including + NULL + + + + Location code string, NULL terminated, identifying the sensor to + be set. + + + + + + + R1--6. + + The platform must not modify the location + code string. + + + + + R1--7. + + The OS must only use this call with sensors + which have been provided by the + ibm,get-indices RTAS call with an index value of + 0xFFFFFFFF. + + + + + R1--8. + + The platform must use the + ibm,get-dynamic-sensor-state RTAS call only for + dynamic sensor types of 9004, 9006 and 9007. + + + + + R1--9. + + A Status of -3 must be returned for the following + conditions: + + + + Sensor type not supported + + + + The specified location code does not identify a valid + sensor + + + + + + +
+ +
+ RTAS Call <emphasis>ibm,get-vpd</emphasis> + This RTAS call allows for collection of VPD that changes after OS + boot time (after the initial reporting in the OF device tree). When this + call is implemented, there is no overlap between what is reported in the + device tree and what is reported with this RTAS call. Also, when this + RTAS call is implemented, all VPD, except PCI and I/O device VPD, which + is dynamically changed during OS run time is reported with this call and + not via the + “ibm,vpd” property in the OF device + tree. + + + + R1--1. + + For all Dynamic Reconfiguration options + except PCI Hot Plug, when the platform VPD can change dynamically due to + a Dynamic Reconfiguration operation, the platform must implement the + ibm,get-vpd RTAS call. + + + + + R1--2. + + The RTAS function + ibm,get-vpd must implement the argument call buffer + defined by + . + + + Argument Call Buffer + <emphasis>ibm,get-vpd</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,get-vpd + + + + + + Number Inputs + + + + 4 + + + + + + Number Outputs + + + + 3 + + + + + + Pointer to Location Code + + + + Real address of NULL-terminated string, contiguous in + real memory and below 4GB, which is the location code of the + FRU for which to obtain the VPD. When this parameter references + a NULL string the VPD for all location codes is + returned. + + + + + + Work Area Address + + + + Address of work area + + + + + + Work Area Size + + + + Size of work area + + + + + + Sequence Number + + + + Integer representing the sequence number of the call. + First call in sequence starts with 1, following calls (if + necessary) use the + Next Sequence Number returned from the + previous call. + + + + + Out + + + + Status + + + + -1: Hardware error + -3: Parameter error + -4: Optional: VPD changed, start again + 0: Success + 1: More data available; call again + 990x: Extended Delay where x is a number 0-5 (see text + below) + + + + + + Next Sequence Number + + + + Return this integer as the + Sequence Number parameter on the next call + to continue the sequence, or 1 if no more calls are + required + + + + + + Bytes Returned + + + + Integer representing the number of valid bytes returned + in the work area. + + + + +
+ When the 990x + Status is returned, it is suggested that software + delay for 10 raised to the x milliseconds (where x is the last digit of + the 990x return code), before calling + ibm,get-vpd with the same input parameters. However, + software may issue the + ibm,get-vpd call again either earlier or later than + this. + + + + + R1--3. + + On the first call to + ibm,get-vpd for a particular VPD gathering operation, + the caller must provide a + Sequence Number of 1 (32-bit integer) + + + + + R1--4. + + Upon calling + ibm,get-vpd with a + Sequence Number of 1, a previously returned + Next Sequence Number must be discarded. This means + that multiple calls to + ibm,get-vpd cannot be interleaved by multiple + processors, and if processor “B” starts a new + ibm,get-vpd sequence while processor “A” + has a call sequence in process (that is, the function on processor + “A” has returned a + Status of 1, and the subsequent call has not yet been + made) then the call sequence on processor “A” is + abandoned. + + + + + R1--5. + + Optionally, if firmware detects a change in + the VPD being requested before the entire VPD is returned, the + ibm,get-vpd call must return a + Status of -4 and the caller must start again with a + Starting Number of 1. + + Implementation Note: The platform should not impede + forward progress by continuously returning a + Status of -4. + + + + + R1--6. + + The return data format in the work area + must be such that after returning all the data and concatenating all data + together in the order received, that the data is the same as is obtained + from the + “ibm,vpd” property of the OF device + tree. + + + + + R1--7. + + Each stanza of the returned data must + include the YL (location code) keyword. + + + + + R1--8. + + If the + ibm,get-vpd RTAS call is implemented, then the + platform must not provide the + “ibm,vpd” or + “ibm,loc-code” properties in the OF + device tree + root node. + + + + + R1--9. + + If the + ibm,get-vpd RTAS call is implemented, then any VPD + which may change after OS boot must be reported via the + ibm,get-vpd RTAS call. + + + + + R1--10. + + If the + Status returned is 1 (more data available, call + again), then the caller must call + ibm,get-vpd again with the + Sequence Number parameter set to the + Next Sequence Number integer from the previously + returned call. + + + + + R1--11. + + If a + Status of anything other than 0 or 1 is returned, the + contents of the work area is not defined. + + + + + R1--12. + + The work area must be contiguous in real + memory and must reside below 4GB. + + + + + R1--13. + + Firmware cannot count on the contents of + the work area at the beginning of any call to + ibm,get-vpd (regardless of the value of the + Sequence Number). + + + + + R1--14. + + The location code referenced by the + Pointer to Location Code parameter must reside in + contiguous real memory below an address of 4GB. + + + + + R1--15. + + If the + ibm,get-vpd RTAS call is implemented, then firmware + must supply the + “ibm,vpd-size” property in the + /rtas node, the value of which is a single cell, + encoded as with + encode-int, which is the estimated maximum size in + bytes of the VPD that is returned if the + Pointer to Location Code parameter to the + ibm,get-vpd RTAS function is NULL (that is, all + system VPD). This size should take in to account possible concurrent + addition of new platform elements after the partition is started. If + firmware is unable to estimate this size, it may return a value of 0x0 to + indicate that no estimate is available. + + Software Implementation Notes: + + + + + An OS should be prepared for older versions of firmware where + the + “ibm,vpd-size” property is not + provided. + + + + Each stanza of the returned data must include the YL (location + code) keyword. + + + + + + +
+ +
+ Managing Storage Preservation + + Platforms may optionally preserve selected regions of storage + (LMBs) across client program boot cycles. + for more information. + + + + R1--1. + + For the Storage Preservation option: The platform + must implement the + ibm,manage-storage-preservation RTAS argument call + buffer as defined by + . + + + <emphasis>ibm,manage-storage-preservation</emphasis> Argument Call + Buffer + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,manage-storage-preservation + + + + + + Number Inputs + + + + 3 + + + + + + Number Outputs + + + + 2 + + + + + + Subfunction + + + + 0 = unused (return -3) + 1 = Register specified LMB for preservation + 2 = Query preservation state of specified LMB + 3 = Deregister for preservation Specific LMB + 4 = Deregister for preservation all caller’s + LMBs. + All other values reserved (return -3) + + + + + + Reg High + + + + The high order 32 bits of the LMB's + “reg” property (Subfunctions + 1-3) + + + + + + Reg Low + + + + The low order 32 bits of the LMB's + “reg” property (Subfunctions + 1-3) + + + + + Out + + + + Status + + + + -1: Hardware error + -2: Busy + -3: Parameter error (Subfunction or Reg invalid; or Reg + for a non-preservable LMB) + 0: Success + 990x: Extended delay where x is a number 0-5 + + + + + + Preservation state + + + + If + Status= Success, the current preservation + state of specified LMB (Subfunctions 1-3) + + + + +
+ + + + + R1--2. + + For the Storage Preservation option: The platform + must include the + “ibm,preservable” property in the + /memory nodes of its OF device tree, containing a + value which reflects the platform's ability to preserve the specific + LMB. + + + + + R1--3. + + For the Storage Preservation option: The value of the + “ibm,preservable” property for the first + LMB must be 0 (cannot be preserved). + + + + + R1--4. + + For the Storage Preservation option: The platform + must not preserve the first LMB, thus must indicate a value of 0 for the + “ibm,preservable” property for the first + LMB. + + + + + R1--5. + + For the Storage Preservation option: The platform + must include the + “ibm,preserved” property in the + /memory nodes of its OF device tree, valued to + reflect the platform's preservation state of the specific LMB. + + + + + R1--6. + + For the Storage Preservation option: The platform, on + a reboot, must include in the OF + /rtas node the + “ibm,preserved-storage” property if the + previous client program registered one or more of its LMBs for + preservation. + + + + + R1--7. + + For the Storage Preservation option: If the client + program registered an LMB for preservation, the platform must preserve + the LMB's storage state across client program reboots. + + + + + R1--8. + + For the Storage Preservation option: The platform, on + a reboot, must include in the OF + /rtas node the + “ibm,request-partition-shutdown” property + which reflects the value of the partition shutdown configuration + variable, and if this property is not present, a value of 0 must be + assumed by the OS. + + + + +
+ +
+ <emphasis>ibm,lpar-perftools</emphasis> RTAS Call + + This RTAS call provides access to platform-level facilities for + performance tools running in a partition on an LPAR system. Platforms may + require platform-specific tools, beyond the scope of this architecture, + to make this call available. + + + + R1--1. + + For the Performance Tool Support option: The platform + must implement the LPAR option. + + + + + R1--2. + + For the Performance Tool Support option: RTAS must + implement the + ibm,lpar-perftools call using the argument call + buffer defined by + . + + + Argument Call Buffer + <emphasis>ibm,lpar-perftools</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,lpar-perftools + + + + + + Number Inputs + + + + 5 + + + + + + Number Outputs + + + + 2 + + + + + + Subfunction + + + + 1: Convert hypervisor IAR value to method name. + + + + + + Work Area Address High + + + + Most significant 32 bits of real address of work + area + + + + + + Work Area Address Low + + + + Least significant 32 bits of real address of work + area + + + + + + Work Area Size + + + + Size of work area in bytes + + + + + + Sequence Number + + + + Integer representing the sequence number of this call. + First call in sequence starts with 1, following calls (if + necessary) use the + Next Sequence Number returned from the + previous call. + + + + + Out + + + + Status + + + + -1: Hardware Error + -2: Busy + -3: Parameter Error (Subfunction invalid, invalid work + area address, invalid work area size) + -9002: Partition does not have authority to perform this + function + -5: Buffer was too small to supply requested data + 0: Success + 990x: Extended delay + + + + + + Next Sequence Number + + + + Return this integer as the + Sequence Number parameter on the next call, + or 1 if no more calls are required. + + + + +
+ When 990x + Status is returned, it is suggested that software + delay for 10 raised to the x milliseconds (where x is the last digit of + the 990x return code), before calling the + ibm,lpar-perftools call with the same input + parameters. However, software may issue the + ibm,lpar-perftools call again earlier or later than + this. + + + + + R1--3. + + For the Performance Tool Support option: For + subfunction value 1, on input the first 8 bytes of + the work area must contain the hypervisor IAR address to be converted. On + output, the first 8 bytes of the work area contain the offset of this + address from the start of the hypervisor function, method or module, + followed by a NULL-terminated text string containing the name of the + hypervisor function, method or module. If the address is not a valid + address in the hypervisor, on output the buffer must contain 0x0 (8 + bytes) followed by a NULL-terminated text string indicating that the + address was not valid. + + + + + R1--4. + + For the Performance Tool support option: The work + area must reside in contiguous memory. + + + + + R1--5. + + For the Performance Tool Support option: If a + Status of anything other than 0 is returned, the + contents of the work area are not defined. + + + + + R1--6. + + For the Performance Tool Support option: A partition + must have at most one call to this function in process at a given time. + This means that if one processor in the partition initiates this call, + receives a Busy or Extended Delay return, and then another processor + calls this function with a sequence number of 1, a subsequent call using + the + Next Sequence Number returned to the first processor + results in a Parameter Error return code. + + + + +
+ +
+ RTAS Call <emphasis>ibm,suspend-me</emphasis> + The + ibm,suspend-me RTAS call provides the calling OS the + ability to suspend processing. Suspension of processing is required as + part of OS hibernation or migration to another platform. This RTAS call + is made by the last active processor thread of a partition. The OS uses + the H_JOIN hcall() (see + ) to deactivate other + processing threads. Processing treads may exit H_JOIN due to an + unmaskable interrupt; if a thread has exited H_JOIN, + ibm,suspend-me fails with a status of “multiple + processor threads active”. The wake up from suspension is triggered + by partition state change (see + sections on "Partition Migration" + and "Partition Hibernation"). The + ibm,suspend-me RTAS call returns only on the calling + virtual processor. Other virtual processors that were inactive when + ibm,suspend-me was called remain so until they are + proded by the OS. + While the logical configuration of a suspended partition remains + static, the physical properties may change; the OS may wish to issue + ibm,update-nodes (see + + ) to determine if any device + tree nodes changed, and then refresh its view of the device + tree physical properties using + ibm,update-properties (see + ) and/or + ibm,configure-connector (see + ). Also during suspension, some + system parameters may have changed. See + , for details. The OS may want + to re-scan selected system parameters. + + + + R1--1. + + For the Partition Suspension option: The platform + must implement the Logical Partitioning option (see + ) + . + + + + + R1--2. + + For the Partition Suspension option: RTAS must + implement the + ibm,suspend-me call within a logical partition using + the argument call buffer defined by + . + + + Argument Call Buffer + <emphasis>ibm,suspend-me</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,suspend-me + + + + + + Number Inputs + + + + 0 + + + + + + Number Outputs + + + + 1 + + + + + Out + + + + Status + + + + 9000: Suspension Aborted + 0: Success -- expected return on function resume + -1: Hardware Error +   + -9004: Partition not suspendable + -9005: Multiple processor threads active + -9006: Outstanding COP Operations + + + + +
+ + + + + R1--3. + + For the Partition Suspension option: The + ibm,suspend-me RTAS call must determine that the + calling partition is in the “suspendable state”, else return + a status of -9004 “Partition not suspendable”. + + + + + R1--4. + + For the Partition Suspension option: The + ibm,suspend-me RTAS call must determine that the + calling partition has no other active processor thread, else return a + status of -9005 “Multiple processor threads active”. + + + + + R1--5. + + For the Partition Suspension option: The platform + must implement the Thread Join option (see + ). + + + + + R1--6. + + For the Partition Suspension option: The platform + must restore all partition state as of the time of the call to + ibm,suspend-me prior to returning from the + ibm,suspend-me RTAS call, except for the values of + those Open Firmware Device tree properties as reported using the Update + OF Tree option, and the system parameters given in + . + + + + + R1--7. + + For the Partition Suspension option: The platform + must be prepared to respond to OS requests for updated device tree + information immediately after returning from the + ibm,suspend-me RTAS call. + + + + + R1--8. + + For the Partition Suspension option: The platform + must support the “update OF tree” option. + + + + + R1--9. + + For the Partition Suspension option: The platform + must support the “Partner partition suspended” CRQ Transport + Event (See + ). + + + + + R1--10. + + For the Partition Suspension option: The + ibm,suspend-me RTAS call must cause the platform to + deliver “Partner partition suspended” CRQ Transport Events to + both CRQs of all CRQ connections associated with the partition calling + ibm,suspend-me. + Note: The transport events are visible to the partition calling + ibm,suspend-me after the subsequent resume from + suspension, while the transport events are immediately visible to the + partner partitions of the caller at the time of the suspend. + + + + + R1--11. + + For the Partition Suspension option: The + ibm,suspend-me RTAS call must cause the platform to + set the state of all of the caller’s CRQs to disabled. + + + + + R1--12. + + For the Partition Suspension option: The platform + must implement the H_ENABLE_CRQ hcall() using the syntax and semantics + described in + . + + + + + R1--13. + + For platforms that implement the Partition Suspension and VSCSI + options: The + “compatible” property of the + platform’s + v-scsi and + v-scsi-host nodes must include + “IBM,v-scsi-2” and + “IBM,v-scsi-host-2” respectively + indicating the platform supports the “Partner partition + suspended” CRQ Transport Event. + + + + + R1--14. + + For the Partition Suspension option: If the OS is + participating in OS surveillance, to avoid a surveillance time out, the + OS must disable surveillance (see + ) prior to calling + ibm,suspend-me. + + + + + R1--15. + + For the Partition Suspension option: The platform + must implement the LRDR option (See + ). + + + + + R1--16. + + For the Partition Suspension option: The logical + configuration of a partition, including its view of the + rtas-display-device, and rtas tone facility must not + change while a partition is suspended. + + + + + R1--17. + + For the Partition Suspension option: The platform + must not change the support for a system parameter during + suspension. + + NOTE: If RTAS returns a status of -3 (System + parameter not supported) prior to suspension, it returns a Status of -3 + for accesses to that same system parameter after suspension. Similarly if + RTAS does not return a Status of -3 prior to suspension for a given + system parameter, it does not do so after suspension. + + + + + R1--18. + + For the Partition Suspension option: The platform + must limit the system parameters that change values during suspension to + those specified in + (all system parameters not + specified are preserved). + + + + + R1--19. + + For the Partition Suspension option: The platform + must preserve up to the first 32 SLB entries for each partition processor + during the suspension. Other SLB entries are subject to loss. + + + + + R1--20. + + For the Partition Suspension option with the Platform + Facilities Option: The + ibm,suspend-me RTAS call must determine that the + calling partition has no outstanding coprocessor operations else return a + status of -9005 “Outstanding COP Operations”. + + + System Parameters that May Change During Partition + Migration and Hibernation + + + + + + + + + System Parameter Token + + + + + Name + + + + +   + + + + + + + + 0-15 + + + HMC + + +   + + + + + 18-19 + + + Legacy processor CoD + + +   + + + + + 20 +   + + + SPLPAR characteristics + + + Only specified SPLPAR keywords may change value + + + + +   + + + DesiredEntitledCapacity + + +   + + + + + DesiredMemory + + +   + + + + + DesiredNumberOfProcessors + + +   + + + + + DesiredVariableCapacityWeight + + +   + + + + + DispatchWheelRotationPeriod + + +   + + + + + MinimumEntitledCapacityPerVP + + + Platform prevents migration where current Entitled + Capacity/VCPU ratio would be below the target's minimum. + + + + + MaximumPlatformProcessors + + +   + + + + + 22 + + + platform_auto_power_restart + + +   + + + + + 23 + + + sp-remote-pon + + +   + + + + + 24 + + + sp-rb4-pon + + +   + + + + + 25 + + + sp-snoop-str + + +   + + + + + 30 + + + sp-call-home + + +   + + + + + 31 + + + sp-current-flash-image + + +   + + + + + 33 + + + epow3-quiesce-time + + +   + + + + + 34 + + + memory-preservation-boot-time + + +   + + + + + 35 + + + SCSI initiator identifier + + +   + + + + + 36 + + + AIX support + + + The keyword “support” may not change to the + value “no” for an AIX client. + + + + + 37 + + + enhanced processor CoD + + +   + + + + + 38 + + + enhanced memory CoD + + +   + + + + + 39 + + + CoD Options + + +   + + + + + 41 + + + firmware boot options + + +   + + + + + 43 + + + processor module information + + +   + + + + +
+ + + + +
+ +
+ RTAS Call <emphasis>ibm,update-nodes</emphasis> + + This RTAS call is used to determine which device tree nodes have + changed due to a massive platform reconfiguration such as when the + partition is migrated between machines. Differing platform + reconfigurations are expected to potentially result in different sets of + nodes being updated; the “scope” argument communicates what + set of changes are to be reported. The work area is a 4 KB naturally + aligned area of storage below the first 4 GB; as such, it may not be + large enough to contain the reports of all changed nodes. The status + value of 1 is used to inform the caller that there are more updates to + report and that it will have to call the + ibm,update-nodes RTAS again to receive them. On + subsequent calls the state variable, which is set to zero on the first + call, is set to the value returned on the previous call, to supply RTAS + with the information it needs to continue from where the previous call + ended. + Upon return, the work area contains, in addition to the state + variable, zero or more operation lists, and logically ends with a + terminator (4 byte word naturally aligned containing 0x00000000). An + operation list consists of an operator (4 bytes naturally aligned) and + zero or more (up to a the maximum number of 4 byte locations remaining in + the work area) operands, each 4 bytes long. An operator consists of a + single byte opcode followed by 3 bytes encoded with the binary value of + the number of operands that follow. An operator with an operand length + field of zero performs no operation, and the opcode of zero is reserved + for the terminator -- thus the terminator can be considered a special + encoding of a no-op operator. + + + + The opcode of 0x01 is used for deleted nodes -- the operands are + the + phandle values for the deleted nodes. + + + + The opcode of 0x02 is used for updated nodes -- the operands are + the + phandle values for the updated nodes. The updated + properties are obtained using the + ibm,update-properties RTAS call. + + + + The opcode of 0x03 is used for adding nodes -- the operands are + pairs of + phandle and + ibm,drc-index values; the + phandle value denotes the parent node of the node to + be added and the + ibm,drc-index value is passed with the + ibm,configure-connector RTAS call to obtain the + contents of the added node. + + + + To make processing of device tree updates simpler, all opcode 0x01 + (delete) operations (if any) are presented prior to all opcode 0x02 + (update) operations (if any), and finally any 0x03 (addition) operations + are presented. The + phandle operand values are the same + phandle values as reported by the + “ibm,phandle” property. + + + + R1--1. + + For the Update OF Tree option: The platform must + include the + “ibm,phandle” property in all OF nodes + specified in + . + + + + + R1--2. + + For the Update OF Tree option: The platform must + implement the + ibm,update-nodes RTAS call using the argument call + buffer defined by + . + + + Argument Call Buffer + <emphasis>ibm,update-nodes</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,update-nodes + + + + + + Number Inputs + + + + 2 + + + + + + Number Outputs + + + + 1 + + + + + + Work Area Address + + + + 32 bit real address of work area + + + + + + Scope + + + + Values per + . + + + + + Out + + + + Status + + + + -1: Hardware Error + -2: Busy + -3: Parameter Error (Purpose does not match the current + partition state) + 0: Success + 1: More nodes updated -- call again + + + + +
+ + + + + R1--3. + + ibm,update-nodes RTAS call work area must be 4 KB + long aligned on a 4 KB boundary that is accessible with MSR[DR] = 0, else + RTAS may return -3 “Parameter Error”. + + + + + R1--4. + + ibm,update-nodes RTAS for a given value of “ + Scope” must be formatted as specified in + , else RTAS may return -3 + “Parameter Error”. + + + Initial Format of Work Area for + <emphasis>ibm,update-nodes</emphasis> + + + + + + 0x00000000 (State Variable indicates Initial call for + specified + Scope) + + + + + + + 12 bytes of 0x00 (reserved) + + + + + Don’t Care . . . + + + + +
+ + + + + R1--5. + + Upon successful return (non-negative status + value) from + ibm,update-nodes the work area must by formatted as + defined in + . (Note each entry in + is 4 bytes long.) + + + Format of Work Area for + <emphasis>ibm,update-nodes</emphasis> + + + + + + State Variable (4 Bytes) + + + + + 12 bytes of 0x00 (reserved) + + + + + 0 or more operation lists + + + + + . . . + + + + + Terminator (0x00000000) + + + + +
+ + + + + R1--6. + + ibm,update-nodes RTAS call operation list for the + ibm,update-nodes RTAS call must contain an operator + (4 bytes naturally aligned) and zero or more 4 byte operands up to the + end of the work area. + + + + + R1--7. + + An operator in an + ibm,update-nodes RTAS call operation list must be + formatted with, starting at the high order byte, a single byte opcode + followed by 3 bytes encoded with the binary value of the number of + operands that follow. + + + + + R1--8. + + An operator in an + ibm,update-nodes RTAS call operation list with an + operand length field of zero must be considered to perform no + operation. + + + + + R1--9. + + The opcode of 0x01 in an + ibm,update-nodes RTAS call operation list must be + used to denote node deletions. + + + + + R1--10. + + The operands for opcode 0x01 in an + ibm,update-nodes RTAS call operation list must be the + + phandle values for the deleted nodes. + + + + + R1--11. + + The opcode of 0x02 in an + ibm,update-nodes RTAS call operation list must be + used to denote updated nodes. + + + + + R1--12. + + The operands for opcode 0x02 in an + ibm,update-nodes RTAS call operation list must be the + phandle values for the updated nodes that may be used + as the + ibm,update-properties RTAS call argument to obtain + the changed properties of the updated node. + + + + + R1--13. + + The opcode of 0x03 in an + ibm,update-nodes RTAS call operation list must used + for the added nodes. + + + + + R1--14. + + The operands for opcode of 0x03 in an + ibm,update-nodes RTAS call operation list must be + phandle and + ibm,drc-index value pairs (each value being 4 bytes + on a natural boundary totalling 8 bytes for the pair) denoting the parent + node of the added node and the + ibm,configure-connector RTAS call argument to obtain + the contents of the added node respectively. + + + + + R1--15. + + All opcode 0x01 (delete) in an + ibm,update-nodes RTAS call operation list (if any) + must be presented prior to any opcode 0x02 (update) operations (if + any). + + + + + R1--16. + + All opcode 0x02 (update) in an + ibm,update-nodes RTAS call operation list (if any) + must be presented prior to any opcode 0x03 (add) operations (if + any). + + + + + R1--17. + + The work area on subsequent call(s) to + ibm,update-nodes RTAS for the same value of the + “Scope” must be formatted as specified in + , else RTAS may return -3 + “Parameter Error”. + + + Format of Work Area for Subsequent Calls to + <emphasis>ibm,update-nodes</emphasis> + + + + + + Value of the 1st 16 bytes of the returned work area from + last call to + ibm,update-nodes RTAS that returned status + of 1. + + + + + + + Don’t Care . . . + + + + +
+ + + + + R1--18. + + The “Scope” argument for the + ibm,update-nodes RTAS call must be one of the values + specified in the scope value column of + , else RTAS may return -3 + “Parameter Error”. + + + + + R1--19. + + For the + ibm,update-nodes RTAS call, the platform must + restrict its reported node updates to those specified in + for the value of the specified + “Scope” argument. + + + Nodes That May be Reported by + <emphasis>ibm,update-nodes</emphasis> for a Given Value of the “ + <emphasis>Scope</emphasis>” Argument + + + + + + + + Scope Value + + + Reportable node types (value of + “name” or + “device_type” property) + + + Supported Opcodes + + + + + + + Negative values: Platform Resource Reassignment events as + from + event-scan RTAS + + + cpu + + + 0x02 + + + + + memory + + + 0x02 + + + + + ibm,dynamic-reconfiguration-memory + + + 0x02 + + + + + + ibm,plaform-facilities + + + + 0x01-0x03 + + + + + + ibm,random-v# + + + + 0x01-0x03 + + + + + + ibm,compression-v# + + + + 0x01-0x03 + + + + + + ibm,encryption-v# + + + + 0x01-0x03 + + + + + 1 Partition Migration / Hibernation + + + + root + + + + 0x02 + + + + + + openprom + + + + 0x02 + + + + + + rtas + + + + 0x02 + + + + + + vdevice + + + + 0x02 + + + + + + cpu + + + + 0x02 + + + + + + cache + + + + 0x01-0x03 + + + + + + options + + + + 0x02 + + + + + + memory + + + + 0x02 + + + + + ibm,dynamic-reconfiguration-memory + + + <all> + + + + + ibm,platform-facilities + + + 0x01-0x03 + + + + + + ibm,random-v# + + + + 0x01-0x03 + + + + + + ibm,compression-v# + + + + 0x01-0x03 + + + + + + ibm,encryption-v# + + + + 0x01-0x03 + + + + + 2 Activate Firmware + + + + rtas + + + + 0x02 + + + + +
+ + + + +
+ +
+ TAS Call <emphasis>ibm,update-properties</emphasis> + + This RTAS call is used to report updates to the properties changed + due to a massive platform reconfiguration such as when the partition is + migrated between machines. This RTAS call reports changes in the node + specified by the phandle value in the work area passed using the Work + Area Address argument. The phandle value may be that of a critical node + that the caller is interested in or one reported by + ibm,update-nodes RTAS call. These changes may include + any combination of new values, deleted and added properties. Updates for + a given node are retained until the platform is subsequently + reconfigured, and remain available to subsequent calls to + ibm,update-nodes. + There may be more changes than can be reported in a single 4 K work + area. In this case, the RTAS call returns with a status of 1 “More + properties updated -- call again”. On the first call, the second + word of the work area contains the value 0 specifying that the RTAS call + is to start with the first changed property for the specified updated + node. On a call with a status value of 1, the first sixteen (16) bytes of + the work area contain values that, when subsequently supplied in the work + area of another call to + ibm,update-properties RTAS, specify that the call + returns the updated property data for properties after those reported in + the previous call. + A single updated property value string may exceed the capacity of a + single 4 K work area. In that case, the updated property value descriptor + for the property appears in the work area of multiple sequential calls to + + ibm,update-properties RTAS. When the updated property + value descriptor contains the final data for the property value, the + property string length field of the updated property value descriptor is + a positive number. When the updated property value descriptor contains + either the initial or interim data for the property value, the updated + property string length field is a negative number denoting the twos + complement of the length of the updated property string contained in the + work area. The data value strings for a given property name are + concatenated until the final updated property value descriptor is + processed. + The first value returned, with an updated property name string of + NULL, is always the node’s name (for example: full path || + name property value || @ unit address) even if there + has been no change. + + + + R1--1. + + For the Update OF Tree option: The platform must + implement the + ibm,update-properties RTAS call using the argument + call buffer defined by + . + + + Argument Call Buffer + <emphasis>ibm,update-properties</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,update-properties + + + + + + Number Inputs + + + + 2 + + + + + + Number Outputs + + + + 1 + + + + + + Work Area Address + + + + 32 bit real address of work area + + + + + + Scope + + + + Values per + . + + + + + Out + + + + Status + + + + -1: Hardware Error + -2: Busy + -3: Parameter Error (Purpose does not match the current + partition state) + 0: Success + 1: More properties updated -- call again + + + + +
+ + + + + R1--2. + + ibm,update-properties RTAS call must be 4 KB long + aligned on a 4 KB boundary that is accessible with MSR[DR] = 0, else RTAS + may return -3 “Parameter Error”. + + + + + R1--3. + + The work area on the first call to + ibm,update-properties RTAS for a given updated node + must be formatted as specified in + , else RTAS may return -3 + “Parameter Error”. + + + Initial Format of Work Area for + <emphasis>ibm,update-properties</emphasis> + + + + + + + phandle of updated node containing updated + properties to be reported (4 bytes) + + + + + + + 0x00000000 (Indicates Initial call for specified + phandle) + + + + + 8 bytes of 0x00 (reserved) + + + + + Don’t Care . . . + + + + +
+ + + + + R1--4. + + Upon successful return (non-negative status + value) from + ibm,update-properties the work area must by formatted + as defined in + . + + + Return Format of Work Area for + <emphasis>ibm,update-properties</emphasis> + + + + + + + + Description + + + + Comments + + + + + + + + phandle of updated node containing updated + properties to be reported. + + + 4 Bytes + + + + + State Variable + (to be returned if status argument value = 1) + + + 4 Bytes + + + + + Reserved + + + 8 bytes + + + + + Number of properties reported in the work area + + + 4 Bytes + The number (N) of updated property value descriptors that + follow -- see below + + + + + N updated property value descriptors + + + Each updated property value descriptor is formatted + as: +   + Null terminated string indicating the name of the updated + property. + followed by: + Value Descriptor -- 4 Bytes decoded as +   + 0x00000000 Name only property ( + “encode-null”) no value + follows +   + 0x80000000 The property is to be deleted no value + follows +   + Other positive values are the length (M) of the + immediately following property value string that completes the + update of the property value. +   + Other negative values are the twos complement of the + length (M) of the immediately following property value string + that either starts or continues the update of the property + value with the remainder in the work area of subsequent call(s) + to + ibm,update-properties. +   + Followed by: + 0-M bytes of property value string. + + + + +
+ + + + + R1--5. + + Upon successful return (non-negative status + value) from + ibm,update-properties when the State Variable had + been 0x00000000, the first updated property descriptor must describe the + fully qualified path name of the node specified by the phandle argument + in the work buffer; the three fields of this updated property descriptor + are: + + + + Property name string is as from + encode-null + + + + Value descriptor is the 4 byte binary length of the value + string + + + + Value string is the fully qualified path name as from the node + name string returned by the open firmware + package-to-path client interface call. + + + + + + + R1--6. + + The work area on subsequent call(s) to + ibm,update-properties RTAS for a given updated node + must be formatted as specified in + , else RTAS may return -3 + “Parameter Error”. + + + Format of Work Area for Subsequent Calls to + <emphasis>ibm,update-properties</emphasis> + + + + + + + phandle of updated node containing updated + properties to be reported (4 Bytes) + + + + + + + Value from last call to + ibm,update-properties RTAS that returned + status of 1 (12 bytes). + + + + + Don’t Care . . . + + + + +
+ + + + + R1--7. + + ibm,update-properties RTAS call, the platform must + restrict its reported property updates to those specified in + for the value of the specified + “Scope” argument. + + + + + R1--8. + + For the + ibm,update-properties RTAS call, the platform must + return a + Status of -3 (Parameter Error) for an unrecognized + value of the “Scope” argument. + + + Properties of the Nodes That May Be Reported by + <emphasis>ibm,update-properties</emphasis> for a “ + <emphasis>Scope</emphasis>” + + + + + + + + Scope Value + + + Reportable node types (value of + “name” or + “device_type” property) + + + Property Name + + + + + + + All negative values: Resource Reassignment events as from + event-scan RTAS + + + /memory + + + “ibm,associativity” + + + + + ibm,dynamic-reconfiguration-memory + + + “ibm,dynamic-memory” + + + + + cpu + + + “ibm,associativity” + + + + + + ibm,random-v# + + + + <all> + + + + + + ibm,compression-v# + + + + <all> + + + + + + ibm,encryption-v# + + + + <all> + + + + + 1 Partition Migration / Hibernation + + + + root + + + + + “ibm,model-class” + + + + + + + “clock-frequency” + + + + + + + + “ibm,extended-clock-frequency” + + + + + + + “model” + + + + + + + “compatible” + + + + + + + “name” + + + + + + + “system-id” + + + + + + + “ibm,partition-no” + + + + + + + “ibm,drc-indexes” + + + + + + + “ibm,drc-names” + + + + + + + “ibm,drc-power-domains” + + + + + + + “ibm,drc-types” + + + + + + + “ibm,aix-diagnostics” + + + + + + + “ibm,diagnostic-lic” + + + + + + + + “ibm,platform-hardware-notification” + + + + + + + + “ibm,ignore-hp-po-fails-for-dlpar” + + + + + + + “ibm,managed-address-types” + + + + + + + “ibm,service-indicator-mode” + + + + + + + openprom + + + + + “model” + + + + + + + rtas + + + + + “power-on-max-latency” + + + + + + + + “ibm,associativity-reference-points” + + + + + + + + “ibm,max-associativity-domains” + + + + + + + “ibm,configure-kernel-dump” + + + + + + + + “ibm,configure-kernel-dump-sizes” + + + + + + + + “ibm,configure-kernel-dump-version” + + + + + + + + “ibm,read-slot-reset-state-functions” + + + + + + + “ibm,configure-pe” + + + + + + + “ibm,change-msix-capable” + + + + + + + vdevice + + + + + “ibm,drc-names” + + + + + + children of the + vdevice node + + + + “ibm,loc-code” + + + + + + 1 Partition Migration / Hibernation +   + + + + cpu + + + + + “name” + + + + + + + “d-cache-sets” + + + + + + + “d-cache-size” + + + + + + + “i-cache-sets” + + + + + + + “i-cache-size” + + + + + + + “bus-frequency” + + + + + + + “ibm,extended-bus-frequency” + + + + + + + + “ibm,extended-clock-frequency” + + + + + + + “clock-frequency” + + + + + + + “timebase-frequency” + + + + + + + “l2-cache” + + + + + + + “performance-monitor” + + + + + + + “ibm,associativity” + + + + + + TLB properties (See + ) + + + + + + “slb-size” + + + + + + + “ibm,tbu40-offset” + + + + + + + “ibm,pi-features” + + + + + + + “ibm,spurr” + + + + + + + “ibm,pa-optimizations” + + + + + + + “ibm,dfp” (sign bit + only) + + + + + + "ibm,sub-processors" + + + + + + + cache + + + + + “d-cache-sets” + + + + + + + “d-cache-size” + + + + + + + “i-cache-sets” + + + + + + + “i-cache-size” + + + + + + + l2-cache + + + + + + + options + + + + + “ibm,dasd-spin-interval” + + + + + + + memory + + + + + “ibm,associativity” + + + + + + + ibm,dynamic-reconfiguration-memory + + + + “ibm,associativity-lookup-arrays” + + + + + “ibm,dynamic-memory” + only the associativity list index fields + + + + + “ibm,memory-preservation-time” + + + + + + /chosen + + + + + “ibm,architecture-vec-5” + + byte 3 (I/O Super Page Option support parameters) + + + + + 1 Partition Migration / Hibernation +   + + + + ibm,random-v# + + + + <all> + + + + + + ibm,compression-v# + + + + <all> + + + + + + ibm,encryption-v# + + + + <all> + + + + + 2 Activate Firmware + + + + rtas + + + + + + Any + /rtas node property as defined per LoPAR + remains invariant. + + + + Any + /rtas node property or definition + extension, except for the value of a function token property*, + may change (provided that the client program has indicated + support for such property or definition extension) including + the following: + + “ibm,read-slot-reset-state-functions” + “ibm,configure-pe” + + + + *NOTE: This exception mandates that if an RTAS function + token property survives a firmware activation, the token value + of that RTAS function call does not change. + + + + +
+ + + + + +
+ +
+ RTAS call <emphasis>ibm,configure-kernel-dump</emphasis> + + This RTAS call is used to register and unregister with the platform + a data structure describing kernel dump information. This dump + information is preserved as needed by the platform in support of a + platform assisted kernel dump option. + + + + R1--1. + + For the Configure Platform Assisted Kernel Dump + option: The platform must implement the + ibm,configure-kernel-dump RTAS call using the + argument call buffer defined by + . + + + Argument Call Buffer + <emphasis>ibm,configure-kernel-dump</emphasis> + + + + + + + + Parameter Type + + + Name + + + Values + + + + + In + + + + Token + + + + Token for + ibm,configure-kernel-dump + + + + + + Number Inputs + + + + 3 + + + + + + Number Outputs + + + + 1 + + + + + + Command + + + + 1: Register for future kernel dump + 2: Unregister for future kernel dump + 3: Complete/Invalidate current kernel dump + + + + + + Work_buffer_address + + + + When command is 1: Register for future kernel dump, + points to a structure as defined in + . + + + + + + Work_buffer_length + + + + Length of Kernel Dump Memory Structure when defined + above + + + + + Out + + + + Status + + + + 0: Success + -1: Hardware Error + -2: Busy + -3: Parameter Error + -9: Dump Already Registered + -10: Dump Active + 990x:Extended Delay + + + + +
+ + + + + R1--2. + + For the Configure Platform Assisted Kernel Dump + option: The work-buffer address and work-buffer-length for the + ibm,configure-kernel-dump RTAS call must point to an + RMR-memory buffer that contains the structures described in + , whenever the command is 1, + register for future kernel dump; otherwise the call may return -3, + “Parameter Error.” + The Dump Memory Structure specified in + is passed by the operating + system during a + ibm,configure-kernel-dump RTAS call. It is also + reported by the platform using the + ibm,kernel-dump RTAS property after a dump has been + initiated. + + + Kernel Assisted Dump Memory Structure + + + + + + + + + + + Header + + + + + + + + Offset + + + Number of Bytes + + + Value + + + + + 0x0 + + + 4 + + + Dump Format Version = 0x00000001 + + + + + 0x4 + + + 2 + + + Number of Kernel Dump Sections + + + + + 0x6 + + + 2 + + + Dump Status Flags + A bit mask with value + 0x8000 = Dump performed (Set to 0 by caller of the + ibm,configure-kernel-dump call) + 0x4000 = Dump was triggered by the previous system boot + (set by platform) + 0x2000 = Dump error occurred (set by platform) + All other bits reserved + + + + + 0x8 + + + 4 + + + Offset to first Kernel Dump Section, offset from the + beginning of the Structure + + + + + 0xc + + + 4 + + + Number of bytes in a block of the dump-disk, if data to + be written to a dump-disk, If not, should be set to 0 + (indicating the no disk dump option.) + + + + + 0x10 + + + 8 + + + Starting block# offset on dump-disk (set to 0 for the no + disk dump option) + + + + + 0x18 + + + 8 + + + Number of blocks on dump-disk usable for dump (set to 0 + for the no disk dump option) + + + + + 0x20 + + + 4 + + + Offset from start of structure to a Null-terminated + Dump-disk path string (set to 0 for the no disk dump + option) + + + + + 0x24 + + + 4 + + + Maximum time allowed (milliseconds) after + Non-Maskable-Interrupt for the OS to call + ibm,configure-kernel-dump + Function 2 (unregister) to prevent an + automatic dump-reboot (set to 0 to disable the automatic + dump-reboot function) + + + + + + Dump-disk Path String + + + + + + Offset specified above + + + Varies + + + Null-terminated Dump-disk path string specifying the + dump-disk. If no disk dump option is indicated, this section is + not included. + + + + + + First Kernel Dump Section + + + + + + Offset specified above + + + 4 + + + Dump Request Flags: + A bit-mask + Bit 0x00000001 When set, firmware to copy source data to + partition memory. This option must be selected if no disk dump + option is indicated. + All other bit values reserved + + + + + Section Start+4 + + + 2 + + + Source Data type, describes section of dump memory being + described + 0x0001 = CPU State Data + 0x0002 = Hardware Page Table for Real Mode Region + 0x0011 = Real Mode Region + 0x0012 = Dump OS identified string (identifies that the + dump is for a particular OS type and version) + 0x0100 - 0xFFFF OS defined source types + All Other values reserved + + + + + Section Start+6 + + + 2 + + + Dump Error Flags (set by platform) + Bit mask + 0x8000 = Invalid section data type + 0x4000 = Invalid source address + 0x2000 = Requested section length exceeds source + 0x1000 = Invalid partition destination address + 0x0800 = Partition memory destination too small + + + + + Section Start+8 + + + 8 + + + Source address (logical address if section came from + partition memory, or byte offset if section is platform + memory) + + + + + Section Start+16 + + + 8 + + + Requested data length, represents number of bytes to + dump + + + + + Section Start+24 + + + 8 + + + Actual data length, number of bytes dumped + + + + + Section Start+32 + + + 8 + + + Destination address, logical address used for sections + not written to disk by the platform, always required for a Real + mode region section and for all sections when the no disk dump + option is used. + + + + + + Subsequent Sections + + + + + + Previous Section Start+40 + + + Start of Next Section + + + A total of up to nine additional 40 bytes sections with + values as described in the First Section may be specified so + long as the entire structure does not exceed 512 bytes for + version 1. + + + + +
+ + + + + R1--3. + + ibm,os-term RTAS call, or on a system reset without + an + ibm,nmi-interlock RTAS call, if the platform has a + dump structure registered through the + ibm,configure-kernel-dump call, the platform must + process each registered kernel dump section as required and, when + available, present the dump structure information to the operating system + through the + “ibm,kernel-dump” property, updated with + status for each dump section, until the dump has been invalidated through + the + ibm,configure-kernel-dump RTAS call. + + + + + R1--4. + + If ibm.comfigure-kernel-dump RTAS call is made to + register or unregister for a dump while a dump is currently active, the + platform must return a + Status of -9, “Dump Active” indicating + that a dump has been copied by the platform and a call must be made to + complete/invalidate the active dump before another call to register or + unregister a dump can be completed successfully. + + + + + R1--5. + + If ibm.comfigure-kernel-dump RTAS call is made to + register a dump after a dump has already been registered by a call, the + platform must return a + Status of -8, “Dump Already Registered” + unless an intervening call was made to invalidate the previously + registered dump. + + + + + R1--6. + + For the Configure Platform Assisted Kernel Dump + Option: Partition memory not specifically mentioned in the call + structure must be preserved by the platform at the same location as + existed prior to the os termination or platform reboot. + + + + + R1--7. + + For the Configure Platform Assisted Kernel Dump + Option: The platform must present the RTAS property, + “ibm,configure-kernel-dump-sizes” in the + OF device tree, which describes how much space is required to store dump + data for the firmware provided dump sections, where the firmware defined + dump sections are: + + + + 0x0001 = CPU State Data + + + + 0x0002 = Hardware Page Table for Real Mode Region + + + + + + + R1--8. + + For the Configure Platform Assisted Kernel Dump + Option: The platform must present the RTAS property, + “ibm-configure-kernel-dump-version” in + the OF device tree. + + + + + R1--9. + + For the Configure Platform Assisted Kernel Dump + Option: After a dump registration is disabled (for example, by + a partition migration operation), calls to + ibm,os-term must return to the OS as though a dump + was not registered. + + Programming Note: The intended flow of interactions + that utilize this call is as follows: + + + + The OS registers sections of memory for dump preservation during + OS initialization + + + + The OS terminates abnormally + + + + The Platform moves registered sections of memory as instructed + during dump registration. + + + + The Partition reboots and provides the prior registration data + in the device tree. + + + + The OS writes the preserved memory regions to disk before using + those memory regions for regular use + + + + The OS completes/invalidates current dump status. + + + + + + +
+ +
+ DMA Window Manipulation Calls + + DMA windows for a PE can be changed by the OS when the platform + implements the Dynamic DMA Windows (DDW) option for a PE. The occurrence + of the + “ibm,ddw-applicable” property in any node + of the OF Device Tree indicates that the platform implements the DDW + option, but that property is required to be in the bridge above a PE in + order for the DDW RTAS call to be applicable for the PE. That is, DDW may + be applicable to some PEs in a platform and not for others. + The platform may implement the DDW RTAS calls even when the OS does + not support these, because they are not required to be used by the OS, + because there is always a default window initially allocated below 4 GB, + as specified by the + “ibm,dma-window” property. During + partition migration, these RTAS calls may come and go, but so will the + “ibm,ddw-applicable” property as the + nodes in which those are supported come or go. + The following is an example of how an OS may grab all DMA window + resources allocated for a PE: + + + + If the default window (as specified by the + “ibm,dma-window” property for the PE) is + not needed, then call + ibm,remove-pe-dma-window for the PE, specifying the + default window LIOBN, to make the maximum resources available for the + ibm,create-pe-dma-window RTAS call. + + + + Call + ibm,query-pe-dma-window for the PE to get the + Windows Available and + PE TCEs available for the PE. If the + Windows Available field indicates 1 or more and the + PE TCEs field is non-zero, then continue. + + + + Call ibm,create-pe-dma-window for the PE, specifying the + size based on the + PE TCEs field obtained from the + ibm,query-pe-dma-window RTAS call in step + and on the I/O page size being + specified. + + + + If the Windows Available field indicated 2 or more in step + , then go back to step + and repeat, otherwise + finished. + + + + Software Implementation Note: The general expectation + is that if the + “ibm,ddw-applicable” property exists for + a PE, that the OS will be able to generate one or more windows whose + total size is larger than what is available via the default window. This + requires either additional TCEs being available or that I/O page sizes + other than 4 KB are available and the PE can use the largest I/O page + size (the default window using only the 4 KB I/O page size). If not, then + removing the default window would only allow re-allocation of the same + size window at a different bus address (that is, same number of TCEs and + same I/O page size). However, it may be possible for this to happen, in + which case the platform may indicate that DDW is available to a PE, but + removal of the default window will only allow creation of the same size + window. An example is when a larger I/O page size is available but only + the TCEs in the default window are available, and the PE cannot make use + of the larger page size. + + + + R1--1. + + For the Dynamic DMA Windows (DDW) option: The + platform must implement all of the following RTAS calls: + ibm,query-dma-window, + ibm,create-dma-window, and + ibm,remove-dma-window. + + + + + R1--2. + + For the Dynamic DMA Windows (DDW) option: The + platform must provide the + “ibm,ddw-applicable” property in the OF + Device Tree in the bridge above each PE for which the DDW option is + supported. + + + + + R1--3. + + For the Dynamic DMA Windows (DDW) option: The + software must not call the + ibm,query-dma-window, + ibm,create-dma-window, or + ibm,remove-dma-window RTAS calls in the absence of + the + “ibm,ddw-applicable” property for the PE, + otherwise the call returns a + Status of -3 (Parameter error), and when the property + does exist, software must use the token values specified in the + “ibm,ddw-applicable” property for these + RTAS calls. + + + + + R1--4. + + For the Dynamic DMA Windows (DDW) option: The + platform must provide a default DMA window for each PE, and all of the + following must be true: + + + + The window is defined by the + “ibm,dma-window” property in the OF + device tree. + + + + The window is defined with 4 KB I/O pages. + + + + The window is located entirely below 4 GB. + + + + + + + R1--5. + + For the Dynamic DMA Windows (DDW) option: + The platform must remove any DMA windows created by the + ibm,create-pe-dma-window RTAS call for a PE and must + restore the default DMA window (if it was removed) for the PE, as + originally defined by the + “ibm,dma-window” properties for the PE, + in each of the following cases: + + + + On a reboot of the partition + + + + On a DR isolate operation that encompasses the PE + + + + + + + R1--6. + + For the Dynamic DMA Windows (DDW) option: + In Requirement + , the platform must provide the + same LIOBN, location, and size as specified in the + “ibm,dma-window” property in the OF + Device Tree for the device. + + + + +
+ <emphasis>ibm,query-pe-dma-window</emphasis> + + This RTAS call allows for the discovery of the resources necessary + to make a successful subsequent call to + ibm,create-dma-window. + + + + R1--1. + + RTAS must implement a + ibm,query-pe-dma-window call using the argument call + buffer defined by + . + + + Argument Call Buffer + <emphasis>ibm,query-pe-dma-window</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,query-pe-dma-window + + + + + + Number Inputs + + + + 3 + + + + + + Number Outputs + + + + 5 + + + + + + Config_addr + + + + PE configuration address (Register fields set to + 0) + + + + + + PHB_Unit_ID_Hi + + + + Represents the most-significant 32-bits of the Unit ID of + the PHB that corresponds to the + config_addr + + + + + + PHB_Unit_ID_Low + + + + Represents the least-significant 32-bits of the Unit ID + of the PHB that corresponds to the + config_addr + + + + + Out + + + + Status + + + + 0: Success + -1: Hardware Error + -3: Parameter error + + + + + Windows Available + + + Number of additional DMA windows that can be created for + this PE. If the value is 0 and the default window (as specified + by the + “ibm,dma-window” property for + the PE) has not been yet removed via the + ibm,remove-pe-dma-window RTAS call for that + window, and if the default window is not needed, then removal + of the default window makes at least one window + available. + + + + + PE TCEs + + + Largest contiguous block of TCEs allocated specifically + for (that is, are reserved for) this PE. See also Requirement + . + + + + + IO Page Sizes + + + I/O Page Size Support. I/O page sizes supported for this + PE. This is a bit significant field, defined as follows: + Bits 0 - 23 reserved + 24 = 16 GB page size supported + 25 = 256 MB page size supported + 26 = 128 MB pages supported + 27 = 64 MB page size supported + 28 = 32 MB page size supported + 29 = 16 MB page size supported + 30 = 64 KB page size supported + 31 = 4 KB page size supported + + + + + Migration Capable + + + H_MIGRATE_DMA Mask. Mask to indicate for which page sizes + (as specified in the I/O Page Size Support field), that + H_MIGRATE_DMA is supported (for this PE). This is a bit + significant field, with the bits defined to align to the bits + in the I/O Page Size Support field. + + + + +
+ + + + + R1--2. + + For the Dynamic DMA Windows (DDW) option: + TCE resources returned in the + PE TCEs parameter of the + ibm,query-dma-window RTAS call must be allocated to + the PE specified by the PE configuration address specified in the call, + and must be available to a subsequent + ibm,create-dma-window RTAS call for that PE. + + + + +
+ +
+ <emphasis>ibm,create-pe-dma-window</emphasis> + + This call allows the creation of a new DMA window, given the size + of the DMA window, I/O page size, and the PE to which it is associated. + The return from the call includes the LIOBN of the new DMA window, the + starting I/O address of the DMA window, and size. + + Software Implementation Note: Software is expected to + not attempt to create a DMA window that is larger than possible, or + create more DMA windows than is possible, otherwise the + ibm,create-pe-dma-window will return a + Status of -3 (Parameter Error). Thus, the OS is + expected to use the + ibm,query-pe-dma-window first and not ask to create a + window that consumes more resources than those that are available to the + PE. + + + + R1--1. + + For the Dynamic DMA Windows (DDW) option: RTAS must + implement the + ibm,create-dma-window call using the argument call + buffer defined by + . + + + Argument Call Buffer + <emphasis>ibm,create-pe-dma-window</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,create-pe-dma-window + + + + + + Number Inputs + + + + 5 + + + + + + Number Outputs + + + + 4 + + + + + + Config_addr + + + + PE configuration address (Register fields set to + 0) + + + + + + PHB_Unit_ID_Hi + + + + Represents the most-significant 32-bits of the Unit ID of + the PHB that corresponds to the + config_addr + + + + + + PHB_Unit_ID_Low + + + + Represents the least-significant 32-bits of the Unit ID + of the PHB that corresponds to the + config_addr + + + + + I/O Page Size + + + The value n, where 2 + n is the requested I/O page size. Only page + sizes obtained from the + ibm,query-pe-dma-window RTAS call for the + PE are allowed. Values of n from 0-11 are invalid. + + + + + Requested Window Size + + + The value n, where 2 + n is the requested DMA window size. + + + + + Out + + + + Status + + + + 990x: Extended delay, where x is a number 0-5 (see + text) + 0: Success (window created) + -1: Hardware Error + -2: Busy, try again later + -3: Parameter Error + + + + + + LIOBN + + + + LIOBN of the DMA window created by this call, if any. If + no DMA window was created (that is, if the + Status is not 0), then this field is + present but not used. + + + + + I/O Starting Address Hi + + + Represents the most-significant 32-bits of the starting + address on the I/O bus for the DMA window created by this call, + if any. If no DMA window was created (that is, if the + Status is not 0), then this field is + present but not used. + + + + + I/O Starting Address Low + + + Represents the least-significant 32-bits of the starting + address on the I/O bus for the DMA window created by this call, + if any. If no DMA window was created (that is, if the + Status is not 0), then this field is + present but not used. + + + + +
+ + + + + R1--2. + + For the Dynamic DMA Windows (DDW) option: The + ibm,create-pe-dma-window RTAS call must return a + Status of 0 (Success) only if a window with the + requested attributes is created, and must not create a new window if a + non-0 + Status is returned. + + + + +
+ +
+ <emphasis>ibm,remove-pe-dma-window</emphasis> + + This RTAS call allows for the removal of PE DMA windows, including + those created with the + ibm,create-pe-dma-window RTAS call as well as the + default window specified by the + “ibm,dma-window” property for the PE. All + created DMA windows will be removed by the platform, and the default DMA + window restored, on a partition reboot, on a DR isolate operation (see + Requirement + and + ), or if the last remaining DMA + window for the PE is removed and that window is not the default DMA + window (see Requirements + and + ). After removal of a DMA + window, software needs to use the + ibm,query-pe-dma-window RTAS call to find out what + resources are available to the PE for subsequent + ibm,create-pe-dma-window RTAS call. + + + + R1--1. + + For the Dynamic DMA Windows (DDW) option: RTAS must + implement the + ibm,remove-dma-window call using the argument call + buffer defined by + . + + + Argument Call Buffer + <emphasis>ibm,remove-pe-dma-window</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,remove-pe-dma-window + + + + + + Number Inputs + + + + 1 + + + + + + Number Outputs + + + + 1 + + + + + + LIOBN + + + + LIOBN of the DMA window to be removed. + + + + + Out + + + + Status + + + + 0: Success + -1: Hardware Error + -3: Parameter error + + + + +
+ + + + + R1--2. + + For the Dynamic DMA Windows (DDW) option: The caller + of the + ibm,remove-pe-dma-window RTAS call must assure that + the TCE table specified by the + LIOBN field does not contain any valid mappings at + the time of the call (that is, that the window is not being used). + + + + + R1--3. + + For the Dynamic DMA Windows (DDW) option: + The platform must + restore the default DMA window for the PE on a call to the + ibm,remove-pe-dma-window RTAS call when all of the + following are true: + + + + The call removes the last DMA window remaining for the + PE. + + + + The DMA window being removed is not the default window. + + + + + + + R1--4. + + For the Dynamic DMA Windows (DDW) option: + In Requirement + , the platform must provide the + same LIOBN, location, and size as specified in the + “ibm,dma-window” property in the OF + Device Tree for the PE. + + + + +
+ +
+ Extensions to Dynamic DMA Windows + + Platforms supporting the DDW option implement extensions described + in this section. These extensions include: adding the + “ibm,ddw-extensions” property see + to those nodes that include the + “ibm,ddw-applicable” property, and + implementing the functional extensions specified for the architectural + level in + . The + “ibm,ddw-extensions” property value is a + list of integers the first integer indicates the number of extensions + implemented and subsequent integers, one per extension, provide a value + associated with that extension. Thus the property value is designed to + grow over time in such a way as to enable earlier client programs to + ignore later firmware extensions and later client programs to operate on + back level firmware. For this level of compatibility to work, the client + code needs to ignore extensions beyond what were defined when the client + code was written, and be prepared to operate on back level platforms t at + do not implement all the extensions that were defined when the client + code was written. + + + DDW Option Extensions + + + + + + + + + DDW Option LoPAR or PAPR Level + + + + + + “ibm,ddw-extensions” list + index + + + + + Value Definition + + + + + + + + 2.7 + + + 2 + + + Token of the i + bm,reset-pe-dma-windows RTAS Call + + + + +
+ + + + R1--1. + + For compatibility with changing extensions to the Dynamic DMA + Windows (DDW) option: The client program must ignore extensions + as represented by + “ibm,ddw-extensions” value list integers + beyond those defined when the client code was written. + + + + + R1--2. + + For compatibility with changing extensions to the Dynamic DMA + Windows (DDW) option: The client program must be prepared to + operate on back level platforms that do not implement all the extensions + that were defined when the client code was written, including no + extensions at all. + + + + + +
+ <emphasis>ibm,reset-pe-dma-windows</emphasis> + The + ibm,reset-dma-windows call resets the TCE table + allocation for the PE to its boot time value as communicated in the + “ibm,dma-window” OF Device Tree property + in the for the PE. + + + + R1--1. + + For the Dynamic DMA Windows (DDW) option starting with + IBM Power Architecture Platform Requirements (PAPR) + level 2.7: RTAS must implement the + ibm,reset-dma-windows call using the argument call + buffer defined by + . + + + Argument Call Buffer + <emphasis>ibm,reset-pe-dma-windows</emphasis> + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + + + + + + + Number Inputs + + + + 3 + + + + + + Number Outputs + + + + 1 + + + + + + config_addr + + + + PE configuration address + + + + + PHB_Unit_ID_HI + + + Represents the most-significant 32-bits of the Unit ID of + the PHB that corresponds to the config_addr + + + + + PHB_Unit_ID_Low + + + Represents the least-significant 32-bits of the Unit ID + of the PHB that corresponds to the config_addr + + + + + Out + + + + Status + + + + 0: Success + -1: Hardware Error + -2: Busy, Try again later + -3: Parameter error + + + + +
+ + + + + R1--2. + + For the Dynamic DMA Windows (DDW) option starting with + IBM Power Architecture Platform Requirements (PAPR) + level 2.7: The caller of the + ibm,reset-pe-dma-windows RTAS call must assure that + the TCE table(s) assigned to the PE specified by the + config_addr field contain no valid mappings at the + time of the call (that is, that the window(s) is not being used). + + + + + R1--3. + + For the Dynamic DMA Windows (DDW) option starting with + IBM Power Architecture Platform Requirements (PAPR) + level 2.7: On a call to + ibm,restore-pe-dma-windows, the platform must + restore the default DMA window per the values provided in the + “ibm,dma-window” Tree property + in the for the PE (same LIOBN, location, and size). + + + + + +
+ +
+ +
+ +
diff --git a/Virtualization/app_bibliography.xml b/Virtualization/app_bibliography.xml new file mode 100644 index 0000000..e0bed27 --- /dev/null +++ b/Virtualization/app_bibliography.xml @@ -0,0 +1,284 @@ + + + + + Bibliography + This section lists documents which were referenced in this specification or which provide + additional information, and some useful information for obtaining these documents. Referenced + documents are listed below. When any of the following standards are superseded by an approved + revision, the revision shall apply. + + + + + + Linux on Power Architecture Reference: Platform and Device Tree + + + + + Linux on Power Architecture Reference: Device Tree + + + + + Linux on Power Architecture Reference: Error Recovery and Logging + + + + + + + Linux on Power Architecture Reference: Runtime Abstraction Services (RTAS) + + + + + Power ISA + + + + + IEEE 1275, IEEE Standard for Boot (Initialization Configuration) Firmware: + Core Requirements and Practices + IEEE part number DS02683, ISBN 1-55937-426-8 + + + + + Core Errata, IEEE P1275.7/D4 + + + + + Open Firmware Recommended Practice:OBP-TFTP + Extension + + + + + Open Firmware Recommended Practice: Device + Support Extensions + + + + + PCI Bus binding to: IEEE Std 1275-1994, Standard + for Boot (Initialization, Configuration) Firmware + + + + + Open Firmware: Recommended Practice - Interrupt + Mapping + + + + + Open Firmware: Recommended Practice - Forth Source + and FCode Image Support, Version 1.0 + + + + + Open Firmware: Recommended Practice - Interrupt + Mapping, Version 1.0 + + + + + Open Firmware: Recommended Practice - TFTP Booting + Extensions, Version 0.8 + + + + + Open Firmware: Recommended Practice - + Interposition, Version 0.2 + + + + + MS-DOS Programmer's Reference + Published by Microsoft + + + + + Peering Inside the PE: A Tour of the Win32 Portable + Executable File Format + Found in the March, 1994 issue of Microsoft Systems Journal + + + + + ISO-9660, Information processing -- Volume and + file structure of CD-ROM for information interchange + Published by International Organization for Standardization + + + + + System V Application Binary Interface, PowerPC + Processor Supplement + By Sunsoft + + + + + ISO Standard 8879:1986, Information Processing + -- Text and Office Systems -- Standard Generalized Markup Language (SGML) + + + + + IEEE 996, A Standard for an Extended Personal Computer + Back Plane Bus + + + + + PCI Local Bus Specification + All designers are responsible for assuring that they use the most current version of this document + at the time that they design conventional PCI related components or platforms. See the PCI SIG website + for the most current version of this document. + + + + + PCI-to-PCI Bridge Architecture Specification + All designers are responsible for assuring that they use the most current version of this document + at the time that they design conventional PCI related components or platforms. See the + PCI SIG website for the most current version of this document. + + + + + PCI Standard Hot-Plug Controller and Subsystem + Specification + + + + + PCI-X Protocol Addendum to the PCI Local Bus Specification + All designers are responsible for assuring that they use the most current version of this document at + the time that they design PCI-X related components or platforms. See the PCI SIG website for the most + current version of this document. + + + + + PCI Express Base Specification + All designers are responsible for assuring that they use the most current version of this document + at the time that they design PCI Express related components or platforms. See the PCI SIG website for + the most current version of this document. + + + + + PCI Express to PCI/PCI-X Bridge Specification + All designers are responsible for assuring that they use the most current version of this document at the + time that they design PCI Express related components or platforms. See the PCI SIG website for the most current + version of this document. + + + + + System Management BIOS (SMBIOS) Reference + Specification + + + + + (List Number Reserved for Compatibility) + + + + (List Number Reserved for Compatibility) + + + + (List Number Reserved for Compatibility) + + + + + IBM RS/6000® Division, Product Topology Data System, + Product Development Guide + Version 2.1 + + + + + Single Root I/O Virtualization and Sharing Specification + All designers are responsible for assuring that they use the most current version of this document at + the time that they design PCI Express SR-IOV related components or platforms. See the PCI SIG website + for the most current version of this document. + + + + + Multi-Root I/O Virtualization and Sharing Specification + All designers are responsible for assuring that they use the most current version of this document at the + time that they design PCI Express MR-IOV related components or platforms. See the PCI SIG website for the + most current version of this document. + + + + + + diff --git a/Virtualization/app_glossary.xml b/Virtualization/app_glossary.xml new file mode 100644 index 0000000..a662dda --- /dev/null +++ b/Virtualization/app_glossary.xml @@ -0,0 +1,1282 @@ + + + + + Glossary + This glossary contains an alphabetical list of terms, phrases, and abbreviations used in this document. + + + + Term + Definition + + + + AC + Alternating current + + + + ACR + Architecture Change Request + + + + AD + Address Data line + + + + Adapter + A device which attaches a device to a bus or which converts one + bus to another; for example, an I/O Adapter (IOA), a PCI Host Bridge (PHB), + or a NUMA fabric attachment device. + + + + + addr + Address + + + + Architecture + The hardware/software interface definition or software module to + software module interface definition. + + + + ASCII + American National Standards Code for Information + Interchange + + + + ASR + Address Space Register + + + + BAT + Block Address Translation + + + + BE + Big-Endian or Branch Trace Enable bit in the + MSR (MSRBE) + + + + BIO + Bottom of Peripheral Input/Output Space + + + + BIOS + Basic Input/Output system + + + + BIST + Built in Self Test + + + + Boundedly undefined + Describes some addresses and registers which when referenced provide + one of a small set of predefined results. + + + + BPA + Bulk Power Assembly. Refers to components used for power distribution + from a central point in the rack. + + + + BPM + Bottom of Peripheral Memory + + + + BSCA + Bottom of System Control Area + + + + BSM + Bottom of System Memory + + + + BUID + Bus Unit Identifier. The high-order part of an interrupt source number + which is used for hardware routing purposes by the platform. + + + + CCIN + Custom Card Identification Number + + + + CD-ROM + Compact Disk Read-Only Memory + + + + CIS + Client Interface Service + + + + CMO + Cooperative Memory Over-commitment option. See + for more information. + + + + + CMOS + Complimentary Metal Oxide Semiconductor + + + + Conventional PCI + Behavior or features that conform to . + + + + CPU + Central Processing Unit + + + + CR + Condition Register + + + + CTR + Count Register + + + + DABR + Data Address Breakpoint Register + + + + DAR + Data Address Register + + + + DASD + Direct Access Storage Device (a synonym for “hard disk”) + + + + DBAT + Data Block Address Translation + + + + DC + Direct current + + + + DEC + Decrementer + + + + DIMM + Dual In-line Memory Module + + + + DMA + Direct Memory Access + + + + DMA Read + A data transfer from System Memory to I/O. A DMA Read Request + is the inbound operation and the DMA Read Reply (or Read Completion) is the + outbound data coming back from a DMA Read Request. + + + + DMA Write + A data transfer to System Memory from I/O or a Message Signalled Interrupt (MSI) DMA Write. This is an inbound operation. + + + + DOS + Disk OS + + + + DR + Data Relocate bit in MSR (MSRDR) + + + + DRA + Deviation Risk Assessment + + + + DRAM + Dynamic Random Access Memory + + + + DRC + Delayed Read Completion. A transaction that has completed + on the destination bus and is now moving toward the originating bus to complete. + DR Connector. + + + + DR entity + An entity that can participate in DR operations. That is, an entity + that can be added or removed from the platform while the platform power is on and the + system remains operational. + + + + DRR + Delayed Read Request. A transaction that must complete on the destination bus before completing on the originating bus. + + + + DSISR + Data Storage Interrupt Status Register + + + + DWR + Delayed Write Request. A transaction that must complete on the destination bus before completing on the originating bus. + + + + EA + Effective Address + + + + EAR + External Access Register + + + + ECC + Error Checking and Correction + + + + EE + External interrupt Enable bit in the MSR (MSREE) + + + + EEH + Enhance I/O Error Handling + + + + EEPROM + Electrically Erasable Programmable Read Only Memory + + + + EPOW + Environment and Power Warning + + + + + Error Log indicator An amber indicator that indicates that the user needs to + look at the error log or problem determination procedures, in order to determine the cause. + Previously called System Information (Attention). + + + + FCode + A computer programming language defined by the OF standard which is semantically + similar to the Forth programming language, but is encoded as a sequence of binary byte codes + representing a defined set of Forth words. + + + + FE0 + Floating-point Exception mode 0 bit in the MSR (MSRFE0) + + + + FE1 + Floating-point Exception mode 1bit in the MSR (MSRFE1) + + + + FIR + Fault Isolation Registers + + + + FLR + Function Level Reset (see PCI Express documentation). An optional reset for PCI Express + functions that allows resetting a single function of a multi-function IOA. + + + + FP + Floating-Point available bit in the MSR (MSRFP) + + + + FPSCR + Floating-Point Status And Control Register + + + + FRU + Field Replaceable Unit + + + + FSM + Finite State Machine + + + + GB + Gigabytes - as used in this document it is 2 raised to the power of 30 + + + + HB + Host Bridge + + + + HMC + Hardware Management Console - used generically to refer to the system + component that performs platform administration function where ever physically located. + The HMC is outside of this architecture and may be implemented in multiple ways. + Examples include: a special HMC applications in another system, an external appliance, + or in an LPAR partition using the Virtual Management Channel (VMC) interface to the + hypervisor. + + + + Hz + Hertz + + + + IBAT + Instruction block address translation + + + + ID + Identification + + + + IDE + Integrated Device Electronics + + + + IDU + Interrupt Delivery Unit + + + + IEEE + Institute of Electrical and Electronics Engineers + + + + I2C + Inter Integrated-circuit Communications + + + + I/O + nput/Output + + + + I/O bus master + Any entity other than a processor, cache, + memory controller, or host bridge which supplies both address and data in + write transactions or supplies the address and is the sink for the data in + read transactions. + + + + I/O device + Generally refers to any entity that is connected + to an IOA (usually through a cable), but in some cases may refer to the IOA + itself (that is, a device in the device tree that happens to be used for I/O + operations). + + + + I/O Drawer + An enclosure in a rack that holds at least one PHB and at + least one IOA. + + + + ILE + Interrupt Little-Endian bit in MSR (MSRILE) + + + + Instr + Instruction + + + + Interrupt Number + See Interrupt Vector below. + + + + Interrupt Vector + The identifier associated with a specific interrupt source. + The identifier’s value is loaded into the source’s Interrupt Vector Register and + is read from the Interrupt Delivery Unit’s Interrupt Acknowledge Register. + + + + IOA + I/O Adapter. A device which attaches to a physical bus which is capable + of supporting I/O (a physical IOA) or logical bus (a virtual IOA). The term “IOA” + without the usage of the qualifier “physical” or “virtual” will be + used to designate a physical IOA. Virtual IOAs are defined further in + . + In PCI terms, an IOA may be defined by a unique combination of its assigned + bus number and device number, but not necessarily including its function number. + That is, an IOA may be a single or multi-function device, unless otherwise specified by + the context of the text. In the context of a PCIe I/O Virtualized (IOV) device (not to be + confused with a virtual IOA), an IOA is a single or multiple function device (for example, a + PCIe Virtual Function (VF) or multiple VFs). An IOA function may or may not have its own set of + resources, that is may or may not be in its own Partitionable Endpoint (PE) domain + (see also + ). + + + + + IOA function + That part of an IOA that deals with a specific part of the + IOA as defined by the configuration space “Function” part of Bus/Device/Function. + For single-function IOAs, the IOA Function and the IOA are synonymous. + + + + IP + Interrupt Prefix bit in MSR (MSRIP) + + + + IPI + Interprocessor Interrupt + + + + IR + Instruction Relocate bit in MSR register (MSRIR) or infrared + + + + ISF + Interrupt 64-bit processor mode bit in the MSR (MSRISF) + + + + ISO + International Standards Organization + + + + ISR + Interrupt Source Register + + + + ISU + Interrupt Source Unit + + + + KB + Kilobytes - as used in this document it is 2 raised to the power of 10 + + + + KHz + Kilo Hertz + + + + LAN + Local Area Network + + + + LCD + Liquid Crystal Display + + + + LE + Little-Endian bit in MSR (MSRLE) or Little-Endian + + + + LED + Light Emitting Diode + + + + LMB + Logical Memory Block. The Block of logical memory addresses associated with a dynamically + reconfigurable memory node. + + + + Load + A Load Request is the outbound (from the processor) operation + and the Load Reply is the inbound data coming back from a + Load Request. When it relates to I/O operations, this is an + MMIO Load . + + + + LR + Link Register + + + + LSb + Least Significant bit + + + + LSB + Least Significant Byte + + + + LSI + Level Sensitive Interrupt + + + + LUN + Logical Unit Number + + + + L1 + Primary cache + + + + L2 + Secondary cache + + + + MB + Megabytes - as used in this document it is 2 raised to the power of 20 + + + + ME + Machine check Enable + + + + MMIO + Memory Mapped I/O. This refers to the mapping of the address space required + by an I/O device for Load or Store operations into + the system’s address space. + + + + MES + Miscellaneous Equipment Specification + + + + MFM + Modified frequency modulation + + + + MHz + Mega Hertz + + + + MOD + Address modification bit in the MSR + (MSRMOD) + + + + MP + Multiprocessor + + + + MSb + Most Significant bit + + + + MSB + Most Significant Byte + + + + MSI + Message Signalled Interrupt + + + + MSR + Machine State Register + + + + MTT + Multi-TCE-Table option. See + . + + + + + N/A + Not Applicable + + + + Nibble + Refers to the first or last four bits in an 8 bit byte + + + + NUMA + Non-Uniform Memory Access + + + + NUMA fabric + Mechanism and method for connecting the multiple nodes of a NUMA system + + + + NVRAM + Nonvolatile Random Access Memory + + + + OF + Open Firmware + + + + OP + Operator + + + + OS + Operating System + + + + OUI + Organizationally Unique Identifier + + + + PA + Processor Architecture + + + + PAP + Privileged Access Password + + + + LoPAR + Used within the Linux on Power Architecture + Reference documents to denote: (1) the architectural requirements specified + by the Linux on Power Architecture Reference document, (2) the Linux on Power Architecture + Reference documents themself, and (3) as an adjective to qualify an entity as being + related to this architecture. + + + + Partitionable Endpoint + This refers to the I/O granule that may be treated as one for + purposes of assignment to an OS (for example, to an LPAR partition). May be an + I/O adapter (IOA), or groups of IOAs and bridges, or portions of IOAs. PE granularity + supported by the hardware may be finer than is supported by the firmware. Grouping + of multiple PEs into one DR entity may limit assignment of a the separate PEs to different + LPAR partitions. See also DR entity. + + + + PC + Personal Computer + + + + PCI + Peripheral Component Interconnect. An all-encompassing term referring to + conventional PCI, PCI-X, and PCI Express. + + + + PCI bus + A general term referring to either the PCI Local Bus, as + specified in and + for conventional PCI and PCI-X, or a PCI Express link, as specified in + for PCI Express. + + + + PCI Express + Behavior or features that conform to + . + + + + PCI link + A PCI Express link, as specified in . + + + + PCI-X + Behavior or features that conform to . + + + + PD + Presence Detect + + + + PE + When referring to the body of the LoPAR, this refers to a Partitionable + Endpoint. + + PE has a different meaning relative to device tree bindings + + (see + for that definition). + + + + + PEM + Partition Energy Management option. See + + . + + + + + Peripheral I/O Space + The range of real addresses which are assigned + to the I/O Space of a Host Bridge (HB) and which are sufficient to contain all of + the Load and Store address space requirements of all the devices in the I/O Space + of the I/O bus that is generated by the HB. A keyboard controller is an example of + a device which may require Peripheral I/O Space addresses. + + + + Peripheral Memory Space + The range of real addresses which are assigned to the Memory + Space of a Host Bridge (HB) and which are sufficient to contain all of the Load and + Store address space requirements of the devices in the Memory Space of the I/O bus + that is generated by the HB. The frame buffer of a graphics adapter is an example + of a device which may require Peripheral Memory Space addresses. + + + + Peripheral Space + Refers to the physical address space which may + be accessed by a processor, but which is controlled by a host bridge. At least one + peripheral space must be present and it is referred to by the suffix 0. A host bridge + will typically provide access to at least a memory space and possibly to an I/O + space. + + + + PHB + PCI Host Bridge + + + + PIC + Programmable Interrupt Controller + + + + PIR + Processor Identification Register + + + + Platform + Refers to the hardware plus firmware portion of a system composed of hardware, + firmware, and OS. + + + + Platform firmware + Refers to all firmware on a system including the software or firmware in a + support processor. + + + + Plug-in I/O card + A card which can be plugged into an I/O + connector in a platform and which contains one or more IOAs and potentially + one or more I/O bridges or switches. + + + + Plug-in Card + An entity that plugs into a physical slot. + + + + PMW + Posted memory write. A transaction that has complete on the + originating bus before completing on the destination bus + + + + PnP + Plug and Play + + + + POP + Power On Password + + + + POST + Power-On Self Test + + + + PR + Privileged bit in the MSR (MSRPR) + + + + Processor Architecture + Used throughout this document to + mean compliance with the requirements specified in + . + + + + Processor revision number + A 16-bit number that distinguishes between various releases + of a particular processor version, for example different engineering change + levels. + + + + PVN + Processor Version Number. Uniquely determines the particular + processor and PA version. + + + + PVR + Processor Version Register. A register in each processor + that identifies its type. The contents of the PVR include the processor + version number and processor revision number. + + + + RAID + Redundant Array of Independent Disks + + + + RAM + Random Access Memory + + + + RAS + Reliability, Availability, and Serviceability + + + + Real address + A real address results from doing address + translation on an effective address when address translation is enabled. + If address translation is not enabled, the real address is the same as the + effective address. An attempt to fetch from, load from, or store to a real + address that is not physically present in the machine may result in a + machine check interrupt. + + + + Reserved + The term “reserved” is used within this + document to refer to bits in registers or areas in the address space + which should not be referenced by software except as described in this + document. + + + + Reserved for firmware use + Refers to a given location or bit which may not be used by + software, but are used by firmware. + + + + Reserved for future use + Refers to areas of address space or bits in registers which may be + used by future versions of this architecture. + + + + RI + Recoverable interrupt bit in the MSR (MSRRI) + + + + RISC + Reduced Instruction Set Computing + + + + RMA + Real Mode Area. The first block of logical memory addresses + owned by a logical partition, containing the storage that may be accessed with + translate off. + + + + ROM + Read Only Memory + + + + Root Complex + A PCI Express root complex as specified in + . + + + + RPN + Real Page Number + + + + RTAS + Run-Time Abstraction Services + + + + RTC + Real Time Clock + + + + SAE + Log Service Action Event log + + + + SCC + Serial Communications Controller + + + + SCSI + Small Computer System Interface + + + + SE + Single-step trace enabled bit in the MSR + (MSRSE) + + + + Service Focal Point + The common point of control in the system for handling all + service actions + + + + Serviceable Event + Serviceable Events are platform, + global, regional and local error events that require a service action + and possibly a call home when the serviceable event must be handled by a + service representative or at least reported to the service provider. + Activation of the Error Log indicator notifies the customer of the event + and the event indicates to the customer that there must be some intervention + to rectify the problem. The intervention may be a service action that the + customer can perform or it may require a service provider. + + + + SES + Storage Enclosure Services (can also mean SCSI Enclosure + Services in relation to SCSI storage) + + + + SF + Processor 32-bit or 64-bit processor mode bit in the MSR + (MSRSF) + + + + SFP + Service Focal Point + + + + Shrink-wrap OS + A single version of an OS that runs on all + compliant platforms. + + + + Shrink-wrap Application + A single version of an application program + that runs on all compliant platforms with the applicable OS. + + + + SMP + Symmetric multiprocessor + + + + SMS + System Management Services + + + + Snarf + An industry colloquialism for cache-to-cache + transfer. A typical scenario is as follows: (1) cache miss from cache A, + (2) line found modified in cache B, (3) cache B performs castout of modified + line, and (4) cache A allocates the modified line as it is being written back + to memory. + + + + Snoop + The act of interrogating a cache for the presence of a + line, usually in response to another party on a shared bus attempting to + allocate that line. + + + + SPRG + Special Purpose Registers for General use + + + + SR + System Registers + + + + SRC + Service Reference Code + + + + SRN + Service Request Number + + + + Store + A Store Request is an + outbound (from the processor) operation. When it relates to I/O + operations, this is an MMIO Store. + + + + System + Refers to the collection of hardware, system firmware, + and OS software which comprise a computer model. + + + + System address space + The total range of addressability as established by the + processor implementation. + + + + System Control Area + Refers to a range of addresses which + contains the system ROM(s) and an unarchitected, reserved, platform-dependent + area used by firmware and Run-Time Abstraction services for control of the + platform. The ROM areas are defined by the OF properties in the + openprom and os-rom nodes + of the OF device tree. + + + + System Information (Attention) indicator + See Error Log indicator. + + + + System firmware + Refers to the collection of all firmware on a system + including OF, RTAS and any legacy firmware. + + + + System Memory + Refers to those areas of memory which form + a coherency domain with respect to the PA processor or processors that + execute application software on a system. + + + + System software + Refers to the combination of OS software, + device driver software, and any hardware abstraction software, but + excludes the application software. + + + + TB + Time Base + + + + TCE + Translation Control Entry + + + + TLB + Translation Look-aside Buffer + + + + TOD + Time Of Day + + + + TOSM + Top of system memory + + + + TPM + Top of Peripheral Memory + Trusted Platform Module + + + + tty + Teletypewriter or ASCII character driven + terminal device + + + + UI + User Interface + + + + USB + Universal Serial Bus + + + + v + Volt + + + + VGA + Video Graphics Array + + + + VMC + Virtual Management Channel + + + + VPD + Vital Product Data + + + + VPNH + Virtual Processor Home Node option. See + . + + + + + + + + + + + + + + diff --git a/Virtualization/bk_main.xml b/Virtualization/bk_main.xml new file mode 100644 index 0000000..c8b35f0 --- /dev/null +++ b/Virtualization/bk_main.xml @@ -0,0 +1,117 @@ + + + + + + + Virtualization + Linux on Power Architecture Reference + + + + + System Software Work Group + + syssw-chair@openpowerfoundation.org + + OpenPOWER Foundation + + + + 2016 + OpenPOWER Foundation + + + Revision 2.0_pre1 + OpenPOWER + + + + + + Copyright details are filled in by the template. + + + + + + The purpose of this document is to provide firmware and software + architectural details for the base Platform hardware associated with an OpenPOWER Systems. + The base content for this document were contributed to the OpenPOWER Foundation in the + IBM Linux on Power Architecture Platform Reference (LoPAPR) Draft + document. It had numerous contributors inside IBM. + This document is a Standard Track, Work Group Specification work product owned by the + System Software Workgroup and handled in compliance with the requirements outlined in the + OpenPOWER Foundation Work Group (WG) Process document. It was + created using the Master Template Guide version 0.9.5. Comments, + questions, etc. can be submitted to the public mailing list for this document at + TBD. + + + + + + 2017-05-18 + + + + Revision 2.0_pre1 - initial conversion from IBM document. Extracted from + Linux on Power Architecture Platform Reference (LoPAPR) version 1.1 dated March 24, + 2016 -- Chapter 14 (Logical Partitioning Option), Chapter 13 (Dynamic Reconfiguration + Option), Chapter 17 (Virtualized Input/Output), Appendix A (SPLPAR Characteristics + Definitions), Appendix D (A Protocol for a Virtual TTY Interface), Appendix E + (A Protocol for VSCSI Communications), Appendix F (A Protocol for VMC Communications), + Appendix J (Platform Dependent hcalls), and Appendix K (A Protocol for VNIC Communications) + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + diff --git a/Virtualization/ch_dynamic_reconfig.xml b/Virtualization/ch_dynamic_reconfig.xml new file mode 100644 index 0000000..6f950f0 --- /dev/null +++ b/Virtualization/ch_dynamic_reconfig.xml @@ -0,0 +1,4314 @@ + + Dynamic Reconfiguration (DR) Architecture + + Dynamic Reconfiguration (DR) is the capability of a system to adapt to + changes in the hardware/firmware physical or logical configuration, and to be + able to use the new configuration, all without having to turn the platform + power off or restart the OS. This section will define the requirements for + systems that support DR operations. + +
+ DR Architecture Structure + + shows the relationship of the DR + architecture with LoPAR and the relationship of the individual DR pieces + with the base DR architecture. Each specific DR option (for example, PCI + Hot Plug) will have a piece that sits on top of the base DR option. The + base DR option is the set of requirements that will be implemented by all + DR platforms and that will be utilized by the OS that supports any of the + specific DR options. The specific DR options will call out the base DR + option requirements as being required. Therefore, in the figure, any + specific DR option is really that specific DR option piece plus the base DR + option. The base DR option is not a stand-alone option; a platform which + supports the base DR option without one or more of the specific DR option + pieces that sit on top of it, has not implemented the DR architecture to a + level that will provide any DR function to the user. Likewise, a DR entity + will meet the requirements of at least one of the specific DR options, or + else software is not required to support it as a DR entity. Thus, the base + DR option is the common building block and structure upon which all other + specific DR options are built. + DR operations can be physical or logical. Currently the only physical + DR entities are PCI Hot Plug. That is, the OS only has control over the + physical DR operations on PCI IOAs. The current direction for hot plug of + other DR entities is to do the physical hot plug (power up/down, control of + service indicators, etc.) via the HMC and to bring the entity into usage by + an OS via logical DR operations (Logical Resource DR -- LRDR). The PCI Hot + Plug DR option can be found in + . The Logical Resource Dynamic + Reconfiguration option can be found in + . It is expected that as time + goes on, the base DR option may be expanded upon by addition of other DR + options. + +
+ DR Architecture Structure + + + + + + + + +
+
+ +
+ Definitions Used in DR + + + DR Definitions + + + + + + + + Term + + + + + Definition + + + + + + + + Base Dynamic Reconfiguration (DR) option + + + The base on which all of the specific DR options are built. + Specific DR options include, for example, the PCI Hot Plug DR + option, processor card DR option, etc. These specific DR options + each include the requirement that all the base DR option + requirements be met. See + for more information + about the structure of the DR architecture pieces. + + + + + Dynamic Reconfiguration (DR) + + + The capability of a system to adapt to changes in the + hardware/firmware configuration with the power on and the OS + operating, and to be able to use the new configuration. This is a + piece of the High Availability puzzle, but only one of the + pieces. + + Addition, removal, and replacement may, in general, be done + with the power on or off on the connector into which the entity + is being added or removed. For the PCI Hot Plug option, the power + to the slot is turned off and the logic signals are electrically + isolated from the connector during the plug or unplug + operation. + + + + + Depth First + + + Refers to a method where a tree structure (for example, a + set of PCI buses connected by PCI to PCI bridges) is traversed + from the top to the bottom before all the siblings at any + particular level are acted upon. + + + + + DR Connector (DRC) + + + The term “DR connector” will be used here to + define the plug-in point for the entity that is participating in + DR. For example, a ‘slot’ into which a PCI IOA is + inserted is a DRC. + + + + + DR Entity + + + An entity that can participate in DR operations. That is, + an entity that can be added or removed from the platform while + the platform power is on and the system remains operational. See + also the definitions of logical and physical DR entities. + + + + + DR Operation + + + The act of removing, adding or replacing a DR + Entity. + + + + + Entity + + + One or more I/O devices, IOAs, Processor cards, etc., that + are treated as one unit. + + + + + High Availability (HA) System + + + A system that gives the customer “close” to + continuous availability, but allows for some system down-time. + Besides DR, other factors that need to be considered in the + design of an HA system include system partitioning, clustering, + redundancy, error recovery, failure prediction, Error Detection + and Fault Isolation (EDFI), software failure detection/recovery, + etc. + + + + + I/O Adapter (IOA) + + + A device which attaches to a physical bus which is capable + of supporting I/O (a physical IOA) or logical bus (a virtual IOA) + and which has its own separate set of resources is referred to as + an IOA. The term “IOA” without the usage of the + qualifier “physical” or “virtual” will be + used to designate a physical IOA. Virtual IOAs are defined + further in + . Resources which must + have the capability of being separate (from other devices) + include: MMIO Load/Store address spaces, configuration address + spaces, DMA address spaces, power domains, error domains, + interrupt domains, and reset domains. Note that the hardware of + an IOA may allow for separation of these resources but the + platform or system implementation may limit the separation (for + example, shared error domains). In PCI terms, an IOA may be + defined by a unique combination of its assigned bus number and + device number, but not including its function number; an IOA may + be a single or multi-function device, unless otherwise specified + by the context of the text. Examples include LAN and SCSI IOAs. A + PCI IOA may exist as multiple device nodes in the OF device tree; + that is, the OF may treat separate “functions” in an + IOA as separate OF device tree nodes. + + + + + IOA: built-in + + + An IOA that is not pluggable by the user. Sometimes called + integrated I/O. As opposed to an IOA that may be removed as part + of a plug-in card removal (see definition for a plug-in card, + below). + + + + + I/O Bus + + + A hardware interface onto which an IOA can be plugged on a + platform. I/O buses discussed here include: + + + + + I/O Bus: PCI + + + The term “PCI” refers to one of: conventional + PCI, PCI-X, or PCI Express. The term “bus” in the + case of PCI Express refers to a PCI Express link. + + + + + I/O Bus: System Bus + + + The system bus in a platform is normally used only to + attach CPUs, memory controllers, and Host Bridges to bridge to + I/O buses. A platform’s system bus may, in certain + circumstances, be used to attach very high speed IOAs. DR of + system bus-attached entities is not considered here. + + + + + I/O Device + + + An entity that is connected to an IOA (usually through a + cable). A SCSI-attached DASD device is an example. Some I/O + devices and their connection points to the IOAs are designed to + be plugged while the connection point is operational to the other + I/O devices connected to the same IOA, and some are not. For + example, while the SCSI bus was not initially designed to have + devices added and removed while the SCSI bus was operational, + different vendors have found ways to do so. For example, + SCSI-attached DASD is pluggable and unpluggable from the SCSI bus + in some platforms. + + + + + Live Insertion + + + A DR operation where the power remains on at the DR + connector. Live insertion entities are always powered unless the + machine power is shut off or unless a subsystem containing those + entities is shut off. + + + + + Logical DR entity + + + A DR entity which does not have to be physically plugged or + unplugged during a DR operation on that entity. See + for a list of the supported + Logical DR types. + + + + + Logical Resource DR + + + The name of the option for support of DR of logical + entities. See + . + + + + + PCI Hot Plug + + + DR for PCI plug-in cards where there is a separate power + domain for each PCI Hot Plug slot. Platforms which do not provide + individual control of power and isolation for each PCI slot but + which do provide power and isolation control for groups of PCI + slots (that is, multiple slots per power domain), do not provide + “PCI Hot Plug,” but can support PCI DR. + + + + + Physical DR entity + + + A DR entity which may need to be physically plugged or + unplugged during a DR operation on that entity. See + for a list of the supported + physical DR types. + + + + + Plug-in card + + + A card which can be plugged into an I/O connector in a + platform and which contains one or more IOAs and potentially one + or more I/O bridges or switches. + + + + + Subsystem + + + One or more I/O devices, IOAs, Processor cards, etc., that + are treated as one unit, for purposes of + removal/insertion. + + + + +
+
+
+ Architectural Limitations + The DR architecture places a few limitations on the implementations. + Current architectural limitations include: + + + + DR operations will be user initiated at the software level before + any physical plugging or unplugging of hardware is performed. This + architecture will be flexible enough to add additional methods for invoking + the process in the future, but for the initial architecture it will be + assumed that the operation is invoked by the user via a software method + (for example, invoking an OS DR services program). It is expected that some + technologies which will be added in the future will allow + plugging/unplugging without the user first informing the software (for + example, P1394 and USB). + + + + Critical system resources cannot be removed via a DR operation. + Which system resources are critical will not be defined by this + architecture; it is expected that this determination will be made by the OS + implementation and/or architecture. Loss of a critical resource would stop + the system from operating. + + + + Many of the RTAS calls will need to work properly, independent of + what is powered-off (for example, NVRAM access must work during DR + operations). This is partially encompassed by the last bullet. For more + information, see + . + + + + Any special requirements relative to redundant power supplies or + cooling are not addressed here. + + + + Moving of a DR entity from one location to another in a platform is + supported through a “remove and add” methodology rather than a + specific architecture which defines the constructs necessary to allow + moving of pieces of the platform around. + + + + Note: The current AIX implementation does a “remove and + add” sequence even when the overall DR operation is a replacement. + That is, first the old entity is removed, and then the new entity is + added. +
+
+ Dynamic Reconfiguration State Transitions + + shows the states and transitions + for the dynamic reconfiguration entities (DR Entities). The transition + between states is initiated by a program action (RTAS functions) provided + the conditions for the transition are met. + + Note: Relative to + , physical DRC types are brought + in to the “owned by the OS” states either: (1) by the Device + Tree at boot time, or (2) by a DLPAR operation, which brings in the logical + DRC “above” the physical DRC first, and drags the physical in + as part of transferring from state 3 to state 4. Therefore no states appear + in the “owned by platform” section under Hot Plug DR in the + figure. So, for example, the DLPAR assignment of a PCI physical slot to an + OS is done by assigning the logical SLOT DRC above the physical PCI slot, + thus giving the following state transitions: state 1, to state 2, to state + 3, to state 4, at which time the OS sees the physical slot, sees an IOA in + the physical slot (via + get-sensor-state (dr-entity-sense) of the physical DRC + returning “present”), and then proceeds with the state + transitions of: state 5, to state 6, to state 7, to state 8. The reverse of + this (DLPAR removal of the PCI slot) is: state 8, to state 6, to state 5, + to state 4, to state 2, to state 1. + +
+ Dynamic Reconfiguration State Transition Diagrams + + + + + + + + +
+ Notes: + + + In State 5, if empty status is returned from the + get-sensor-state dr-entity-sense call, then do not attempt to power-on + + + Transitions from State 8 to 6 or from State 6 to 5 may fail + (set-indicator isolation-state isolate, and get-sensor-state + dr-entity-sense) if the hardware cannot be accessed to control + these operations. In this case, the OS may ignore + those errors if the operation is a DLPAR to remove the + hardware. See also the “ibm,ignore-hp-po-fails-for-dlpar” + property in . + + + +
+
+ Base DR Option + +
+ For All DR Options - Platform Requirements + + This section contains the extra requirements placed on + the platform for all of the various DR configurations. + At this time, there are no provisions made in the DR architecture + for unexpected removal of hardware or insertion of hardware into a DR + connector. Therefore the user is expected to interact with the DR + software prior to changing the hardware configuration. For example, it is + expected that most systems will require a keyboard action prior to the + hardware configuration change. Future architecture might allow for other + possibilities. For example, a push-button switch at the DR connector may + be provided which causes an interrupt to the OS to signal that an + operation is about to take place on the connector + The push-button method is one that has been mentioned as a + possible enhancement for systems that are produced for telephone + company applications. + . + As mentioned in + , the requirements in this + section are not stand-alone requirements; the platform will also need to + implement one or more of the specific DR options. + + + + R1--1. + + For all DR options: If the + “ibm,configure-connector” + property exists in the + /rtas node of the OF device tree, then the platform + must meet all of the requirements for the Base DR option (that is, all of + the requirements labeled “For all DR options”), and must also + meet all the requirements for at least one of the specific DR + options. + + + + + R1--2. + + For all DR options: The platform and + OS must adhere to the design and usage restrictions on RTAS routines + defined in + , and any RTAS calls not + specified in + must comply with + Note + and + . + + + RTAS Call Operation During DR Operations + + + + + + + + + + + + RTAS Call Name + + + + + + Reference to + Note + Numbers + + + + +   + + + + + + RTAS Call Name + + + + + + Reference to + Note + Numbers + + + + + + + + + rtas-last-error + + + + 1 + + +   + + + + ibm,read-pci-config + + + + 4 + + + + + + check-exception + + + + 1, 2 + + + + + ibm,write-pci-config + + + + 4,7 + + + + + + display-character + + + + 1 + + + + + restart-rtas + + + + 1 + + + + + + event-scan + + + + 1, 2 + + + + + set-indicator + + + + 3, 4, 5 + + + + + + query-cpu-stopped-state + + + + 4 + + + + + set-power-level + + + + 3, 4, 5 + + + + + + get-power-level + + + + 4 + + + + + set-time-for-power-on + + + + 1 + + + + + + get-sensor-state + + + + 3, 4 + + + + + set-time-of-day + + + + 1 + + + + + + get-time-of-day + + + + 1 + + + + + start-cpu + + + + 4 + + + + + + ibm,configure-connector + + + + 7 + + + + + stop-self + + + + 7 + + + + + + ibm,exti2c + + + + 1 + + + + + system-reboot + + + + 1 + + + + + + ibm,os-term + + + + 1 + + + + + nvram-store + + + + 1 + + + + + + nvram-fetch + + + + 1 + + + + + power-off + + + + 1, 6 + + + + + + ibm,power-off-ups + + + +   + + + +   + + +   + + + + +
+ + Notes: + + + + + These RTAS calls + function as specified in this architecture, regardless of the power state + of any DR entity in the platform (providing the call is + implemented). + + + + These RTAS calls + do not cause errors nor return an error status by accessing hardware + which is isolated, unusable and/or powered down. + + + + These RTAS calls function properly when dealing with a DR + connector, when the parent of that DR connector is powered and + configured, regardless of the state of the child of the parent (for + set-indicator, the isolation-state and dr-indicator names, and for + get-sensor-state, the dr-entity-sense sensor name). + + + + The results of the OS issuing these RTAS calls to hardware when + the access to that hardware is through hardware which is isolated, + unusable, powered off, or incompletely configured, are + indeterminate. + + + + The results of the OS changing the power or isolation state of a + Dynamic Reconfigure connector while there is an uncompleted + ibm,configure-connector operation in progress against + that connector are indeterminate. + + + + Power domains which were defined within sub-trees which have + been subsequently isolated may remain un-modified by this call; their + state will be platform dependent. + + + + The results of the OS issuing these RTAS calls to hardware which + is isolated and/or powered off are indeterminate. + + + + + + + + R1--3. + + For all DR options: If there is Forth code associated + with a DR entity, it must not modify the OF device tree properties or + methods unless modifications can be hidden by the + ibm,configure-connector RTAS call (that is, where + this RTAS routine recognizes the entity and creates the appropriate OF + device tree characteristics that would have been created by the Forth + code). + + + + + R1--4. + + For all DR options: The hardware must protect against + any physical damage to components if the DR entity is removed or inserted + while power is on at the DR connector. + + + + + R1--5. + + For all DR options: During a DR operation (including + resetting and removing the reset from the entity, powering up and + powering down the entity, unisolating and isolating the entity, and + physically inserting and removing the entity), the platform must prevent + the introduction of unrecoverable errors on the bus or interconnect into + which the DR entity is being inserted or removed. + + + + + R1--6. + + For all DR options: During a DR operation (including + resetting and removing the reset from the entity, powering up and + powering down the entity, unisolating and isolating the entity, and + physically inserting and removing the entity), the platform must prevent + damage to the DR entity and the planar due to any electrical + transitions. + + + + + R1--7. + + For all DR options: If there are any + live insertion DR entities in a platform and if those entities or the + rest of the platform cannot tolerate the power being turned off to those + entities during DR operations on other DR entities, then they must not be + placed in the same power domain as the DR entities that will be powered + off. + + + + + R1--8. + + For all DR options: A separate visual + indicator must be provided for each physical DR connector which can be + used for insertion of a DR Entity or which contains a DR entity that can + be removed, and the indicator must be individually controllable via the + set-indicator RTAS call, and must have the capability + to be set to the states as indicated in + and + . + + + + + R1--9. + + For all DR options: + If a platform provides a separate indicator to indicate the state of the power for the + DR connector, then that LED must be turned on by the platform when the + platform turns the power on to the DR connector and must be turned off by + the platform when the platform turns the power off to the DR + connector. + + + + + R1--10. + + For all DR options: If a DR entity requires power to + be turned off prior to the physical removal of the DR entity from the + platform, then the hardware must provide a green power indicator to + indicate the power state of the DR entity + + + + + R1--11. + + For all DR options: The platform must provide any + necessary power sequencing between voltages within a power domain during + DR operations (for example, during the + set-power-level RTAS call). + + + + + R1--12. + + For all DR options: If a platform supports DR, then + all DR entities must support the full on to off and the off to full on + power transitions. + + Architecture Note: Requirement + is necessary so that the OS can + count on the availability of certain RTAS facilities and so that the OS + does not use other RTAS facilities when they are not available. This may + put certain hardware restrictions on what can and cannot be shut + down. + + Hardware Implementation Notes: + + + + + Requirement + requires careful planning of + hardware design and platform structure to assure that no resources + critical to RTAS are put into power domains that are powered down as part + of a DR operation. In addition, the platform is required to provide the + facilities (registers and bits in registers readable by firmware, etc.) + so that RTAS can query the state of the hardware and determine if + something is powered off before actually accessing the powered-off + hardware. + + + + Requirement + indicates that there cannot be + any sharing of indicators between DR connectors. + + + + In some large systems (for example, systems with many racks of + equipment) it may not be possible or convenient to view the individual DR + visual indicators without opening cabinet doors, etc. In such cases, the + designers of such systems could consider putting a “summary” + visual indicator where the user could readily see it, which is basically + a logical “or” of the visual indicators which are out of + sight. For example, in a rack-based system, the drawers might have an + indicator on the front of the drawer that indicates if any indicators on + the back of the drawer are flashing. This summary indicator will not be + accessed by the software (that is, will be transparent to the software) + but it is permissible for the indicator to have firmware + dependencies. + + + + + + +
+ +
+ For All DR Options - OF Requirements + This section describes the OF properties added for DR and any + additional requirements placed on OF due to DR. + This section defines a number of new DR properties which are + arrays. All properties for a specific DR connector under a node are at + the same offset into each array. Also, when the descriptive text states + “the first connector” this does not imply any physical + position or numbering, but rather a logical “first” connector + beneath a particular node in the OF device tree. + +
+ General Requirements + + + + R1--1. + + For all DR options: When the firmware passes control + to the OS, the DR hardware must be initialized such that all of the DR + connectors which would return “DR entity present” to a + get-sensor-state dr-entity-sense) are fully powered + and operational and any DR visual indicators are set to the appropriate + state (on or off) as indicated by + . + + + + + R1--2. + + For all DR options: After the firmware has passed + control to the OS, the state of the DR visual indicators must not change + except under the following conditions: + + + + As directed to do so by the + set-indicator RTAS call. + + + + Under the condition of a power-fault, in which case the hardware + may change the state of the visual indicator to the “off” + state if it turns the power off to the slot. + + + + + + + R1--3. + + For all DR options: The platforms which have + hierarchical power domains must provide the + “power-domains-tree” property in the OF + device tree. + + + + +
+ +
+ Property + <emphasis role="bold"><literal>“ibm,drc-indexes”</literal></emphasis> + This property is added for the DR option to specify for each DR + connector an index to be passed between the OS and RTAS to identify the + DR connector to be operated upon. This property is in the parent node of + the DR connector to which the property applies. See + for the definition of this + property. + + + + R1--1. + + For all DR options: For each OF device tree node + which supports DR operations on its children, the OF must provide an + “ibm,drc-indexes” property for that + node. + + + +
+ +
+ Property + <emphasis role="bold"><literal>“ibm,my-drc-index”</literal></emphasis> + This property is added for the DR option to specify for each node + which has a DR connector between it and its parent, the value of the + entry in the + “ibm,drc-indexes” property for that + connector. This property is used for correlation purposes. See + for the definition of this + property. + + + + R1--1. + + For all DR options: For each OF device tree node + which has a DR connector between it and its parent, the OF must provide an + “ibm,my-drc-index” property for that + node. + + + +
+ +
+ Property + <emphasis role="bold"><literal>“ibm,drc-names”</literal></emphasis> + This property is added for the DR option to specify for each DR + connector a user-readable location code for the connector. See + for the definition of this + property. + + + + R1--1. + + For all DR options: For each OF device tree node + which supports DR operations on its children, the OF must provide an + “ibm,drc-names” property for that + node. + + + + + R1--2. + + For all DR options: The content of the + “ibm,drc-names” property must be of the + format defined in + . + + + + + + <emphasis role="bold"><literal>“ibm,drc-names”</literal></emphasis> Property Format + + + + + + + + + DRC Type + + + + + DRC Name + + + + + + + + 1-8, 11-30 (PCI Hot Plug) + + + Location code + + + + + SLOT + + + Location code (built-in has port suffix) + + + + + PORT + + + Port x + + + + + CPU + + + CPU x + where “x” is a decimal number with one or + more digits and no leading zeroes + + + + + MEM or MEM-n + + + LMB x + where “x” is a decimal number with one or + more digits and no leading zeroes + + + + + PHB + + + PHB x + where “x” is a decimal number with one or + more digits and no leading zeroes + + + + +
+
+ +
+ <emphasis role="bold"><literal>“ibm,drc-power-domains”</literal></emphasis> Property + This property is added for the DR option to specify for each DR + connector the power domain in which the connector resides. See + for the definition of this + property. + + + + R1--1. + + For all DR options: + For each OF device tree node which supports DR operations on its children, the OF + must provide an + “ibm,drc-power-domains” property for that + node. + Software Implementation Notes: + + + + Software will not call the + set-power-level RTAS call with an invalid power + domain number, and for purposes of this call, a power domain number of -1 + (a live insert connector) is considered invalid. + + + + For the case where the power domain is -1 (the live insert case), + this does not imply that the connector does not need isolating before the + DR operation, only that it does not need to be powered off. + + + + + + + +
+ +
+ Property + <emphasis role="bold"><literal>“ibm,drc-types”</literal></emphasis> + This property is added for the DR option to specify for each DR + connector a user-readable connector type for the connector. See + for the definition of this + property. + + Architecture Note: The logical connectors (CPU, MEM + etc.) represent DR boundaries that may not have physical DR connectors + associated with them. If a physical DR boundaries were present they would + be represented by a different DR connector type. It is possible that a + given boundary may be represented by both a physical and a logical + connector. In that case, logical assignment would be managed with the + logical connector and physical add/remove would be managed by specifying + the physical DR connector. + + + + R1--1. + + For all DR options: For each OF device tree node + which supports DR operations on its children, the OF must provide an + “ibm,drc-types” property for that + node. + + + +
+ +
+ Property + <emphasis role="bold"><literal>“ibm,phandle”</literal></emphasis> + This property is added for the DR option to specify the phandle for + each OF device tree node returned by ibm,configure-connector. See + for the definition of this + property. + + + + R1--1. + + For all DR options: The + ibm,configure-connector RTAS call will include the + “ibm,phandle” property in each OF device + tree node that it returns. This phandle must be unique and consistent + with any phandle visible to an OF client program or any other information + returned by + ibm,configure-connector. + + + +
+
+ +
+ For All DR Options - RTAS Requirements + For platforms that implement DR, there is one new RTAS call and + some changes (new requirements) placed on existing ones. + +
+ General Requirements + The following are the general requirements for RTAS for all DR + options. + + + + R1--1. + + For all DR options: + If there is Forth + code associated with a DR entity and that Forth code would normally + modify the OF device tree properties or methods, then if that entity is + to be supported as a DR entity on a particular platform, the + ibm,configure-connector RTAS call on that platform + must recognize that entity and create the appropriate OF device tree + characteristics that would have been created by the Forth code. + + + + +
+ +
+ <emphasis>set-power-level</emphasis> + This RTAS call is defined in + . Several additional requirements are placed + on this call when the platform implements DR along with PM. + This RTAS call is used in DR to power up or power down a DR + connector, if necessary (that is, if there is a non-zero power domain + listed for the DR connector in the + “ibm,drc-power-domains” property). The + input is the power domain and the output is the power level that is + actually to be set for that domain; for purposes of DR, only two of the + current power levels are of interest: “full on” and + “off.” + For sequencing requirements between this RTAS routine and others, + see Requirements + and + . + + + + R1--1. + + For all DR options: the + set-power-level RTAS call must be implemented as + specified in + and the further requirements of this DR + option. + + + + + R1--2. + + For all DR options: The + set-power-level RTAS call must initiate the operation + and return “busy” status for each call until the operation is + actually complete. + + + + + R1--3. + + For all DR options: + If a DR operation + involves the user inserting a DR entity, then if the firmware can + determine that the inserted entity would cause a system disturbance, then + the + set-power-level RTAS call must not power up the + entity and must return an error status which is unique to that particular + type of error, as indicated in + . + + + + + + + <emphasis>set-power-level</emphasis> Error Status for specific DR + options + + + + + + + + + + Parameter Type + + + + + Name + + + + + Option Name + + + + + Values + + + + + + + + Out + + + Status + + + PCI Hot Plug DR option + + + -9000: Powering entity would create change of frequency + on the bus and would disturb the operation of other PCI IOAs on + the bus, therefore entity not powered up. + + + + +
+ Hardware Implementation Notes: + + + + For any DR operation, the firmware could optionally not allow + powering up of a DR entity, if the powering up would cause a platform + over-power condition (the firmware would have to be provided with the DR + Entities’ power requirements and the platform’s power + capability by a method which is not architected by the DR + architecture). + + + + If PM is not implemented in the platform, then only the + “full on” and “off” states need to be implemented + for DR and only those two states will be used. + + + + + Software Implementation Note: The operation of the + set-power-level call is not complete at the time of + the return from the call if the “busy” status is returned. If + it is necessary to know when the operation is complete, the routine + should be called with the same parameters until a non-busy status is + returned. +
+ +
+ <emphasis>get-sensor-state</emphasis> + This RTAS call is defined in + . This RTAS call will be used + in DR to determine if there is something connected to the DR + connector. + The + “rtas-sensors” and + “ibm,sensor-<token>” + OF properties are not applicable to DR + sensors defined in + . + + + + R1--1. + + For all DR options: RTAS must implement the + get-sensor-state RTAS call. + + + + + R1--2. + + For all DR options: The sensor values specified in + must be implemented as + specified in that table. + + + <emphasis>get-sensor-state</emphasis> Defined Sensors for All DR + Options + + + + + + + + + + Sensor Name + + + + + Token Value + + + + + Defined Sensor Values + + + + + Description + + + + + + + + dr-entity-sense + + + 9003 + + + DR connector empty (0) + + + Returned for physical DR entities if the connector is + available (empty) for an add operation. The DR connector must + be allocated to the OS to return this value, otherwise a status + of -3, no such sensor implemented, will be returned from the + get-sensor-state RTAS call. + + + + + DR entity present (1) + + + Returned for logical and physical DR entities when the DR + connector is allocated to the OS and the DR entity is present. + For physical DR entities, this indicates that the DR connector + actually has a DR entity plugged into it. For DR connectors of + physical DR entities, the DR connector must be allocated to the + OS to return this value, otherwise a status of -3, no such + sensor implemented, will be returned from the + get-sensor-state RTAS call. For DR + connectors of logical DR entities, the DR connector must be + allocated to the OS to return this value, otherwise a sensor + value of 2 or 3 will be returned. + + + + + DR entity unusable (2) + + + Returned for logical DR entities when the DR entity is + not currently available to the OS, but may possibly be made + available to the OS by calling + set-indicator with the allocation-state + indicator, setting that indicator to usable. + + + + + DR entity available for exchange (3) + + + Returned for logical DR entities when the DR entity is + available for exchange in a sparing type operation, in which + case the OS can claim that resource by doing a + set-indicator RTAS call with + allocation-state set to exchange. + + + + + DR entity available for recovery (4) + + + Returned for logical DR entities when the DR entity can + be recovered by the platform and used by the partition + performing a + set-indicator RTAS call with + allocation-state set to recover. + + + + +
+ + + + + R1--3. + + For all DR options except the PCI Hot Plug and LRDR + options: + If the + get-sensor-state call with the dr-entity-sense sensor + requires the DR entity to be powered up and/or unisolated to sense the + presence of the DR entity, then the + get-sensor-state call must return the error code of + -9000 or -9001, as defined in + , if the DR entity is powered + down or is isolated when the call is made. + + + <emphasis>get-sensor-state</emphasis> Error Status for All DR + Options + + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + Out + + + Status + + + -9000: Need DR entity to be powered up and unisolated + before RTAS call + -9001: Need DR entity to be powered up, but not + unisolated, before RTAS call + -9002: (see architecture note, directly below) + + + + +
+ + Architecture Note: The -9002 return code should not + be implemented. For legacy implementations if it is returned, then it + should be treated by the caller the same as a return value of 2 (DR + entity unusable). + + + + + R1--4. + + For all DR options: + The value used + for the sensor-index input to the + get-sensor-state RTAS call for the sensors in + must be the index for the + connector, as passed in the + “ibm,drc-indexes” property. + + Hardware and Software Implementation Note: The status + introduced in Requirement + is not valid for + get-sensor-state calls when trying to sense insertion + status for PCI slots (see Requirement + ). + + Architecture Note: DR entity available for recovery + state is intended to allow a platform to temporary allocate to itself + resources on a reboot and then allow the OS to subsequently recover those + resources when no longer needed by the platform. An example of use would + be the platform temporarily reserving some LMBs to itself during a reboot + to store dump data, and then making the LMBs available to a OS partition + by marking them with the state of “available for recovery” + after the dump data has been transferred to the OS. + + + + +
+ +
+ <emphasis>set-indicator</emphasis> + This RTAS call is defined as shown in + . This RTAS call is used in DR to transition + between isolation states, allocation states, and control DR indicators. + In some cases, a state transition fails due to various conditions, + however, a null transition (commanding that the new state be what it + already is) always succeeds. As a consequence, this RTAS call is used in + all DR sequences to logically (and if necessary physically) isolate and + unisolate the connection between a DR entity and the platform. If + physical isolation is indeed required for the DR entity, this RTAS call + determines the necessity for isolation, not the calling program. + The + set-indicator allocation-state and + set-indicator isolation-state are linked. Before + calling + set-indicator with isolation-state set to unisolate, + the DR entity being unisolated will first need to be allocated to the OS. + If the + get-sensor-state call would return a value of DR + entity unusable or if it would return an error like -3 for the DR entity, + then the + set-indicator isolation-state to unisolate would fail + for that DR entity. + For sequencing requirements between this RTAS routine and others, + see Requirements + and + . + A single + set-indicator operation for indicator type 9001 may + require an extended period of time for execution. Following the + initiation of the hardware operation, if the + set-indicator call returns prior to successful + completion of the operation, the call will return either a status code of + -2 or 990x. A status code of -2 indicates that RTAS may be capable of + doing useful processing immediately. A status code of 990x indicates that + the platform requires an extended period of time, and hints at how much + time will be required before completion status can be obtained. Neither + the 990x nor the -2 status codes imply that the platform has initiated + the operation, but it is expected that the 990x status would only be used + if the operation had been initiated. + The following are the requirements for the base DR option. Other DR + options may put additional requirements on this RTAS call. + + indicates which DR indicators + are used with which DR connector types. + The + “rtas-indicators” and + “ibm,indicator-<token>” + OF properties are not applicable to DR + indicators defined in + . + + + + R1--1. + + For all DR options: The indicator state values + specified in + must be implemented as + specified in that table. + + + <emphasis>set-indicator</emphasis> Defined Indicators for all DR + Options + + + + + + + + + + + Indicator Name + + + + + Token Value + + + + + Defined State Values + + + + + Default Value + + + + + Examples/Comments + + + + + + + + isolation-state + + + 9001 + + + Isolate (0), + Unisolate (1) + + + Unisolated + + + This indicator must be implemented for DR connectors for + both physical and logical DR entities. Isolate refers to the DR + action to logically disconnect the DR entity from the platform. + An isolate operation makes the DR entity available to the + firmware, and in the case of a physical DR entity like a PCI + IOA, logically disconnects the DR entity from the platform (for + example, from the PCI bus). Unisolate refers to the DR action + to logically connect the entity. Before + set-indicator isolation-state to unisolate, + the DR entity being unisolated must first be allocated to the + OS. If the + get-sensor-state call with the + dr-entity-sense token would return a value of DR entity + unusable or if it would return an error like -3 for the DR + entity, then the + set-indicator isolation-state to unisolate + must fail for that DR entity. + + + + + dr-indicator + + + 9002 + + + Inactive (0), + Active (1), + Identify (2) + Action (3) + + + 0 if Inactive + 1 if Active + + + This indicator must be implemented for DR connectors for + physical DR entities. If the DR indicators exist for the DR + connector, then they are used to indicate the state of the DR + connector to the user. Usage of these states are as defined in + and + . + + + + + allocation-state + + + 9003 + + + unusable (0) + usable (1) + exchange (2) + recover (3) + + + NA + + + This indicator must be implemented for DR connectors for + logical DR entities. Used to allocate and deallocate entities + to the OS. The initial allocation state of a connector is + established based upon the initial allocation of resources to + the OS image. Subsequently, an OS may request a change of + allocation state by use of the + set-indicator with allocation-state token. + If the transition to the usable state is not possible the -3 + (no such indicator implemented) status is returned. + + + + +
+ + + + + R1--2. + + For all DR options: + The value used for the indicator-index input to the + set-indicator RTAS call for the indicators in + must be the index for the + connector, as passed in the + “ibm,drc-indexes” property. + + + + + R1--3. + + For all DR options: The + set-indicator call must return a -2 status, or + optionally for indicator type 9001 the 990x status, for each call until + the operation is complete; where the 990x status is defined in + . + + + + + R1--4. + + For all DR options: If this is a DR operation that + involves the user inserting a DR entity, then if the firmware can + determine that the inserted entity would cause a system disturbance, then + the + set-indicator RTAS call must not unisolate the entity + and must return an error status which is unique to the particular + error. + + + + + R1--5. + + For all DR options: If the + set-indicator index refers to a connector that would + return a “DR entity unusable” status (2) to the + get-sensor dr-entity-sense token, the + set-indicator RTAS return code must be “No such + indicator implemented” (-3), except in response to a successful + set-indicator allocation state usable. + + + + + R1--6. + + For all DR options combined with the LPAR option: The + RTAS + set-indicator specifying unusable allocation-state of + a DR connector must unmap the resource from the partition’s Page + Frame Table(s) and, as appropriate, its Translation Control Entry + tables. + + + + + R1--7. + + For all DR options combined with the LPAR option: The + successful completion of the RTAS + set-indicator specifying usable allocation-state of a + DR connector must allow subsequent mapping of the resource as appropriate + within the partition’s Page Frame Table(s) and/or its Translation + Control Entry tables. + + Software Implementation Note: The operation of the + set-indicator call is not complete at the time of the + return from the call if the “busy” status is returned. If it + is necessary to know when the operation is complete, the routine should + be called with the same parameters until a non-busy status is + returned. + + Hardware and Software Implementation Note: The + set-indicator (isolation-state) call is used to clear + RTAS internal tables regarding this device. The + ibm,configure-connector RTAS routine will need to be + called before using the entities below this connector, even if power was + never removed from an entity while it was in the isolated state. + + + +
+ +
+ <emphasis>ibm,configure-connector</emphasis> RTAS Call + The RTAS function + ibm,configure-connector is a new RTAS call introduced + by DR and is used to configure a DR entity after it has been added by + either an add or replace operation. It is expected that the + ibm,configure-connector RTAS routine will have to be + called several times to complete the configuration of a dynamic + reconfiguration connector, due to the time required to complete the + entire configuration process. The work area contains the intermediate + state that RTAS needs to retain between calls. The work area consists of + 4096 byte pages of real storage on 4096 byte boundaries which can be + increased by one page on each call. The OS may interleave calls to + ibm,configure-connector for different dynamic + reconfiguration connectors, however, a separate work area will be + associated with each dynamic reconfiguration connector which is actively + being configured. Other standard RTAS locking rules apply. + The properties generated by the + ibm,configure-connector call are dependent on the + type of DR entities. For a list of properties generated, see the RTAS + Requirements section for each specific DR option. For example, for a list + of properties generated for PCI Hot Plug, see + . + For sequencing requirements between this RTAS routine and others, + see Requirement + . + + + + R1--1. + + For all DR options: The RTAS function + ibm,configure-connector must be implemented and must + implement the argument call buffer defined by + . + + + <emphasis>ibm,configure-connector</emphasis> Argument Call Buffer + + + + + + + + + Parameter Type + + + + + Name + + + + + Values + + + + + + + + In + + + + Token + + + + Token for + ibm,configure-connector + + + + + + Number Inputs + + + + 2 + + + + + + Number Outputs + + + + 1 + + + + + + Work area + + + + Address of work area + + + + + + Memory extent + + + + 0 or address of additional page + + + + + Out + + + + Status + + + + -9003: Cannot configure - Logical DR connector unusable, + available for exchange, or available for recovery. + -9002: Cannot configure - DR Entity cannot be supported + in this connector + -9001 Cannot configure - DR Entity cannot be supported in + this system + -2: Call again + -1: Hardware error + 0: Configuration complete + 1: Next sibling + 2: Next child + 3: Next property + 4: Previous parent + 5: Need more memory + 990X: Extended Delay + + + + +
+ + + + + R1--2. + + For all DR options: On the first call of a dynamic + reconfiguration sequence, the one page work area must be initialized by + the OS as in + . + + + Initial Work Area Initialization + + + + + + + + + Entry Offset + + + + + Value + + + + + + + + 0 + + + entry from the + “ibm,drc-indexes” property for + the connector to configure + + + + + 1 + + + 0 + + + + +
+ + Architecture Note: The entry offset in + is either four bytes or eight + bytes depending on whether RTAS was instantiated in 32-bit or 64-bit + mode, respectively. + + + + + R1--3. + + For all DR options: On all subsequent calls of the + sequence, the work area must be returned unmodified from its state at the + last return from RTAS. + + + + + R1--4. + + For all DR options: The + ibm,configure-connector RTAS call must update any + necessary RTAS configuration state based upon the configuration changes + effected through the specified DR connector. + + + + + The sequence ends when either RTAS returns a “hardware + error” or “configuration complete” status code, at + which time the contents of the work area are undefined. If the OS no + longer wishes to continue configuring the connector, the OS may recycle + the work area and never recall RTAS with that work area. Unless the + sequence ends with Configuration Complete, the OS will assume that any + reported devices remain unconfigured and unusable. RTAS internal data + structures (outside of the work area) are not updated until the call + which returns “configuration complete” status. A subsequent + sequence of calls to + ibm,configure-connector with the same entry from the + “ibm,drc-indexes” property will restart + the configuration of devices which were not completely configured. + If the index from + “ibm,drc-indexes” refers to a connector + that would return an “DR entity unusable” status (2) to the + get-sensor RTAS call with dr-entity-sense token, the + ibm,configure-connector RTAS call for that index + immediately returns “-9003: Cannot configure - Logical DR connector + unusable” on the first call without any configuration action taken + on the DR connector. + A dynamic reconfiguration connector may attach several sibling OF + device tree architected devices. Each such device may be the parent of + one or more device sub-trees. The + ibm,configure-connector RTAS routine configures and + reports the entire sub-tree of devices rooted in previously unconfigured + architected devices found below the connector whose index is specified in + the first entry of the work area, except those that are associated with + an empty or unowned dynamic reconfiguration connector; where unowned + refers to a DR connector that would return a DR entity unusable, a DR + entity available for exchange, or a DR entity available for entity + available for recovery value, for a + get-sensor dr-entity-sense sensor. Configuration + proceeds in a depth first order. + If the + ibm,configure-connector RTAS routine returns with the + “call again” or 990x status, configuration is proceeding but + had to be suspended to maintain the short execution time requirement of + RTAS routines. No results are available. The OS should call the + ibm,configure-connector RTAS routine passing back the + work area unmodified at a later time to continue the configuration + process. + If the + ibm,configure-connector RTAS routine returns with a + “Cannot configure - DR Entity cannot be supported in this + connector”, then there is a lack of one or more resources at this + connector for this DR Entity and there is at least one DR connector in + the system into which this DR Entity can be configured. In this case, the + DR program should indicate to the user that they need to consult the + appropriate system documentation relative to the DR Entity that they are + trying to insert into the system. + The “need more memory” status code, is similar in + semantics to the “call again” status. However, on the next + ibm,configure-connector call, the OS will supply, via + the + Memory extent parameter, the address of another page + of memory for RTAS to add to the work area in order for configuration to + continue. On all other calls to + ibm,configure-connector the contents of the + Memory extent parameter should be 0. It is the + responsibility of the OS to recover all work area memory after a sequence + of + ibm,configure-connector calls is completed. + + Software Implementation Note: The OS may allocate the + work area from contiguous virtual space and pass individual discontiguous + real pages to + ibm,configure-connector as needed. + If the + ibm,configure-connector RTAS routine returns either + the “next sibling” or “next child” status codes, + configuration has detected an architected OF device tree device, and is + returning its OF device tree node-name. Work Area offset 2 contains an + offset within the first page of the work area to a NULL terminated string + containing the node-name. Note, if the caller needs to preserve this or + any other returned parameters between the various calls of a + configuration sequence it will copy the value to its own area. Also, the + first call returning configuration data will have a “next + child” status code. + The “next property” status code indicates that a + subsequent property is being returned for the device. Work Area entry + offset 2 contains an offset within the first page of the work area to a + NULL terminated string containing the property name. Work Area entry + offset 3 contains the length of the property value in bytes. Work Area + entry offset 4 contains an offset within the first page of the work area + to the value of the property. + + Architecture Note: The + ibm,configure-connector RTAS routine returns those + applicable properties that can be determined without interpreting any + FCode ROM which is associated with the IOA. Additionally, it is + permissible for this RTAS call to be aware of various specific IOAs and + emulate the action of any FCode associated with the IOA. + If the + ibm,configure-connector RTAS routine returns the + “previous parent” status code, it has come to the end of the + string of siblings, and will back up the tree one level following its + depth first order algorithm. The 2nd through 4th work area entries are + undefined for this status code. + + Software Implementation Notes: + + + + Any attempts to configure an already configured connector or one + in progress of being configured will produce unpredictable + results. + + + + The software will put the DR entity in the full on power state + before issuing the + ibm,configure-connector RTAS call to configure the DR + entity. + + + +
+
+ +
+ For All DR Options - OS Requirements + + +
+ Visual Indicator States + DR Visual indicator usage will be as indicated in the following + requirement, in order to provide for a consistent user interface across + platforms. Information on implementation dependent aspects of the DR + indicators can be found in + . + + + + R1--1. + + For all DR options: The visual indicators must be + used as defined in + . + + + + + + Visual Indicator Usage + + + + + + + + + State of indicator + + + + + Usage + + + + + + + + Inactive + + + The DR connector is inactive and entity may be removed or + added without system disruption. For DR entities that require + power off at the connector, then the caller of + set-indicator must turn power off prior to + setting the indicator to this state. See also + . + + + + + Identify (Locate) + + + This indicator state is used to allow the user to + identify the physical location of the DR connector. This state + may map to the same visual state (for example, blink rate) as + the Action state, or may map to a different state. See also + . + + + + + Action + + + Used to indicate to the user the DR connector on which + the user is to perform the current DR operation. This state may + map to the same visual state (for example, blink rate) as the + Identify state, or may map to a different state. See also + . + + + + + Active + + + The DR connector is active and entity removal may disrupt + system operation. See also + . + + + + +
+
+ +
+ Other Requirements + + + + R1--1. + + For all DR options: The OS must detect hierarchical + power domains (as specified in the + “power-domains-tree” property) and must + handle those properly during a DR operation. + + + + + R1--2. + + For all DR options: + When bringing a + DR entity online, the OS must issue the following RTAS calls in the + following order: + + + + + If the power domain is not 0, then call + set-power-level + + + + set-indicator (with the isolation-state token and a + state value of unisolate) + + + + ibm,configure-connector + + + + + + + R1--3. + + For all DR options: + When taking a DR + entity offline, the OS must issue the following RTAS calls in the + following order: + + + + set-indicator with the isolation-state token and a + state value of isolate) + + + + If the power domain is not 0, then call + set-power-level + + + + + + + R1--4. + + When bringing a DR entity online that + utilizes TCEs (see + ), the OS must initialize the DR + entity's TCEs. + + + + +
+
+
+ +
+ PCI Hot Plug DR Option + This section will develop the requirements over and beyond the base + DR option requirements, that are unique to being able to perform DR + operations on PCI plug-in cards that do not share power domains with other + PCI plug-in cards. + +
+ PCI Hot Plug DR - Platform Requirements + A method will be provided to isolate the plug-in card (power and + logic signals) and to physically remove the plug-in card from the + machine. The physical removal may pose an interesting mechanical + challenge, due to the position of the card edge connector relative to the + desired direction of insertion of the card from the outside of the + machine. In addition, PCI plug-in cards may have internal cables and may + span multiple slots. Such mechanical issues are not addressed by this + architecture. + This section describes the requirements for the platform when a + platform implements the PCI Hot Plug DR option. + + + + R1--1. + + For the PCI Hot Plug DR option: All platform + requirements of the base DR option architecture must be met ( + ). + + + + + R1--2. + + For the PCI Hot Plug DR option: All PCI requirements + must be met (for example, timing rules, power slew rates, etc.) as + specified in the appropriate PCI specifications, and in the + . + + + + + R1--3. + + For the PCI Hot Plug DR option: + The hardware must + provide two indicators per PCI Hot Plug slot, and all the following must + be true: + + + One indicator must be green and the platform must use the + indicator to indicate the power state of the PCI Hot Plug slot, turning + on the indicator when the slot power is turned on and turning off the + indicator when the slot power is turned off. + + + + The other indicator must be amber and must be controllable by + RTAS, separately from all other indicators, and must be used as a slot + Identify indicator, as defined in + . + + + + + + + + R1--4. + + For the PCI Hot Plug DR option: + The hardware must + provide a separate power domain for each PCI Hot Plug slot, controllable + by RTAS, and that power domain must not be used by any other DR connector + in the platform. + + + + + R1--5. + + For the PCI Hot Plug DR option: + The hardware must + provide the capability to RTAS to be able to read the insertion state of + each PCI Hot Plug slot individually and must provide the capability of + reading this information independent of the power and isolation status of + the plug-in card. + + + + + R1--6. + + For the PCI Hot Plug DR option: + The hardware must + provide individually controllable electrical isolation (disconnect) from + the PCI bus for each PCI Hot Plug slot, controllable by RTAS and this + isolation when set to the isolation mode must protect against errors + being introduced on the bus, and damage to the plug-in cards or planars + during the plug-in card power up, power down, insertion, and + removal. + + + + + R1--7. + + For the PCI Hot Plug option: + A platform must + prevent the change in frequency of a bus segment (for example, on the + insertion or removal of an plug-in card) while that change of frequency + would result in improper operation of the system. + + + + + R1--8. + + For the PCI Hot Plug option: For each PCI Hot Plug + slot which will accept only 32-bit (data width) plug-in cards, the + platform must: + + + Accommodate plug-in cards requiring up to 64 MB of PCI Memory + Space and 64 KB of PCI I/O space + + + + For TCE-mapped DMA address space, must provide the capability to + map simultaneously and at all times at least 128 MB of PCI Memory space + for the slot. + + + + + + + + R1--9. + + For the PCI Hot Plug option: Each PCI Hot Plug slot + which will accept 64-bit (data width) plug-in cards, the platform + must: + + + Accommodate plug-in cards requiring up to 128 MB of PCI Memory + Space and 64 KB of PCI I/O space + + + + For TCE-mapped DMA address space, must provide the capability to + map simultaneously and at all times at least 256 MB of PCI Memory space + for the slot. + + + + + + + + R1--10. + + For the PCI Hot Plug option with PCI Express: The + power and isolation controls must be implemented by use of the PCI + Standard Hot-Plug Controller (see + ). + + + + + R1--11. + + For the PCI Hot Plug option with PCI Express: If a + PCI Hot Plug DRC contains multiple PEs, then that DRC must be owned by + the platform or a trusted platform agent. + + Hardware implementation Notes: + + + + Surge current protection on the planar is one way to provide the + required protection against damage to components if an entity is removed + from or inserted into a connector with the power still applied to the + connector. + + + + Removal of an entity without the proper quiescing operation may + result in a system crash. + + + + In order for hot plugging of PCI plug-in cards with the system + operational to be useful, a mechanical means is needed in order to be + able to remove or insert PCI plug-in cards without shutting off system + power and without removing the covers above the plug-in cards (which in + general, would require powering-down the system). + + + + It is recommended that the control of the indicators required by + Requirement + be via the PCI Standard Hot + Plug Controller (see + ). + + + + + + + +
+ +
+ PCI Hot Plug DR - Boot Time Firmware Requirements + + + + R1--1. + + For the PCI Hot Plug DR option: All OF requirements + of the base DR option architecture must be met ( + ). + + + + + R1--2. + + For the PCI Hot Plug DR option: The OF must only + generate the + “clock-frequency” OF property for PCI + bridge nodes which cannot change bus clock frequency during a PCI Hot + Plug operation. + + + + + R1--3. + + For the PCI Hot Plug DR option: The OF must set the + PCI configuration register bits and fields appropriately. + + + + + + Hardware Implementation Note: The OF should leave + sufficient gaps in the bus numbers when configuring bridges and switches + such that plug-in cards with bridges and switches which are to be + supported by the platform’s DR operations can be plugged into every + slot in the platform in which those plug-in cards are supported. That is, + insertion of an plug-in card that contains a bridge or switch into a + platform, requires that there be sufficient available bus numbers + allocated to that PCI bus such that new bus numbers can be assigned to + the buses generated by the bridges and switches on the plug-in + cards. +
+ +
+ PCI Hot Plug DR - Run Time Firmware Requirements + + + + R1--1. + + For the PCI Hot Plug DR option: All RTAS requirements + of the base DR option architecture must be met ( + ). + + + + + R1--2. + + For the PCI Hot Plug DR option: The + set-indicator RTAS call with a indicator type of + isolation-state and a state value of unisolate (1) must not return a + “success” status until any IOA on a plug-in card inserted + into the PCI slot is ready to accept configuration cycles, and must + return a “success” status if the PCI slot is empty. + + + + + R1--3. + + For the PCI Hot Plug DR option: The + ibm,configure-connector RTAS call must initialize the + PCI configuration registers and platform to the same values as at boot + time. + + Architecture Note: During a DR replace operation, the + replacement PCI IOA may not get placed back at the same addresses, etc., + as the original DR entity by the firmware (although it has to be placed + back into the same DR connector, or it is not a DR replace operation). On + a replace operation, the configuration information cannot reliably be + read from the IOA being replaced (the IOA might be broken), so the + firmware cannot read the configuration information from the old IOA and + replace the configuration information into the new IOA. + PCI I/O sub-systems architecturally consist of two classes of + devices, bus bridges (Processor Host Bridges (PHBs), PCI to PCI Bridges, + and PCI Express switches and bridges) and IOAs. The support that + ibm,configure-connector provides for these two + classes is different. + For Bus Bridges, firmware will totally configure the bridge so that + it can probe down the depth of the tree. For this reason, the firmware + must include support for all bridges the platform supports. This includes + interrupt controllers as well as miscellaneous unarchitected devices that + do not appear in the OF device tree. The properties supported and + reported are the same as provided by the boot time firmware. + For PCI plug-in cards, the support is significantly less; it is + essentially the functionality specified in section 2.5 FCode Evaluation + Semantics of the + . However, the configuration + proceeds as if all devices do not have an expansion ROM since the RTAS + code does not attempt to determine if an FCode ROM is present nor + attempts to execute it. This may, in some cases, generate different + device node properties, values and methods than would happen had the IOA + been configured during boot. If the IOA’s device driver or + configuration support cannot deal with such differences, then the IOA is + not dynamically reconfigurable. The other properties generated are + dependent upon the IOA’s configuration header from the following + list. If the property is not on this list the reader should assume that + RTAS + ibm,configure-connector will not generate it. + + shows what PCI OF properties + can be expected to be returned from the + ibm,configure-connector call for PCI Hot Plug + operations and + shows some which can be + expected to not be returned. + + + + + R1--4. + + For the PCI Hot Plug DR option: The + ibm,configure-connector RTAS call when used for PCI + IOAs must return the properties named in + except as indicated in the + Present?/Source column. + + + PCI Property Names which will be Generated by + <emphasis>ibm,configure-connector</emphasis> + + + + + + + + Property Name + + + + + Present?/Source + + + + + + + + + “name” + + + + Always present. + + + + + + “vendor-id” + + + + Always present. From PCI header. + + + + + + “device-id” + + + + Always present. From PCI header. + + + + + + “revision-id” + + + + Always present. From PCI header. + + + + + + “class-code” + + + + Always present. From PCI header. + + + + + + “interrupts” + + + + Only present if Interrupt Pin register not 0. + + + + + + “min-grant” + + + + Present unless Header Type is 0x01. + + + + + + “max-latency” + + + + Present unless Header Type is 0x01. + + + + + + “devsel-speed” + + + + Only present for conventional PCI and PCI-X. + + + + + + “compatible” + + + + Always present. Constructed from the PCI header + information for the IOA or bridge. + + + + + + “fast-back-to-back” + + + + Only present for conventional PCI and PCI-X when Status + Register bit 7 is set. + + + + + + “subsystem-id” + + + + Only present if “Subsystem ID” register not + 0. + + + + + + “subsystem-vendor-id” + + + + Only present if “Subsystem vendor ID” + register not 0. + + + + + + “66mhz-capable” + + + + Only present for conventional PCI and PCI-X when Status + Register bit 5 is set. + + + + + + “133mhz-capable” + + + + Only present for PCI-X when PCI-X Status Register bit 17 + is set. + + + + + + “266mhz-capable” + + + + Only present for PCI-X when PCI-X Status Register bit 30 + is set. + + + + + + “533mhz-capable” + + + + Only present for PCI-X when PCI-X Status Register bit 31 + is set. + + + + + + “reg” + + + + Always present. Specifies address requirements. + + + + + + “assigned-addresses” + + + + Always present. Specifies address assignment. + + + + + + “ibm,loc-code” + + + + Always present. RTAS will have to remember the location + codes associated with all DR connectors so that it can build + this property. + + + + + + “ibm,my-drc-index” + + + + Always present. + + + + + + “ibm,vpd” + + + + Always present for sub-systems and for PCI IOAs which + follow the PCI VPD proposed standard. See + + and note to see the effect of + using different PCI versions. + + + + + + “device_type” + + + + For bridges, always present with a value of + “PCI” otherwise not + present. + + + + + + “ibm,req#msi” + + + + Present for all PCI Express IOA nodes which are + requesting MSI support, when the platform supports MSIs. + + + + +
+ + is a non-exhaustive list of + common properties that may not be generated by RTAS + ibm,configure connector for a PCI IOA. Also, the + concept of a phandle does not apply to nodes reported by + ibm,configure-connector. + + + Non-exhaustive list of PCI properties that may not be + generated by + <emphasis>ibm,configure connector</emphasis> + + + + + + + + + Property Name + + + + + Present?/Source + + + + + + + + + “ibm,connector-type” + + + + Never present -- only for built-in entries not for + pluggable ones. + + + + + + “ibm,wrap-plug-pn” + + + + Never present -- only for built-in entries not for + pluggable ones. + + + + + + “alternate-reg” + + + + Never present -- needs FCode. + + + + + + “fcode-rom-offset” + + + + Never present -- RTAS does not look for this. + + + + + + “wide” + + + + Never present -- needs FCode. + + + + + + “model” + + + + Never present -- needs FCode. + + + + + + “supported-network-types” + + + + Never present -- needs FCode. + + + + + + “address-bits” + + + + Never present -- needs FCode. + + + + + + “max-frame-size” + + + + Never present -- needs FCode. + + + + + + “local-mac-address” + + + + Never present -- needs FCode. + + + + + + “mac-address” + + + + Never present -- needs FCode. + + + + + + “built-in” + + + + Not present for a PCI Hot Plug connectors. + + + + +
+ + Architecture Note: Without + “device_type” and other properties, the + OS cannot append an IOA added via DR to the boot list for use during the + next boot. + + + + + R1--5. + + For the PCI Hot Plug option: When + ibm,configure-connector RTAS call returns to the + caller, if the device driver(s) for any IOA(s) configured as part of the + call are EEH unaware (that is may produce data integrity exposures due to + an EEH stopped state) or if they may be EEH unaware, then the + ibm,configure-connector call must disable EEH prior + to returning to the caller. + + Software Implementation Note: To be EEH aware, a + device driver does not need to be able to recover from an EEH stopped + state, only recognize the all-1's condition and not use data from + operations that may have occurred since the last all-1's checkpoint. In + addition, the device driver under such failure circumstances needs to + turn off interrupts (using the + ibm,set-int-off RTAS call) in order to make sure that + any (unserviceable) interrupts from the IOA do not affect the system. + Note that this is the same device driver support needed to protect + against an IOA dying or against a no-DEVSEL type error (which may or may + not be the result of an IOA that has died). Note that if all-1’s + data may be valid, the + ibm,read-slot-reset-state2 RTAS call should be used + to discover the true EEH state of the device. + + + +
+ +
+ PCI Hot Plug DR - OS Requirements + + + + R1--1. + + For the PCI Hot Plug DR option: All OS requirements + of the base DR option architecture must be met ( + ). + + + + +
+
+ +
+ Logical Resource Dynamic Reconfiguration (LRDR) + The Logical Resource Dynamic Reconfiguration option allows a platform + to make available and recover platform resources such as CPUs, Memory + Regions, Processor Host Bridges, and I/O slots to/from its operating OS + image(s). The Logical Resource Dynamic Reconfiguration option provides the + means for providing capacity on demand to the running OS and provides the + capability for the platform to make available spare parts (for example, + CPUs) to replace failing ones (called + sparing operations). Combined with the LPAR option, + platforms can move resources between partitions without rebooting the + partitions’ OS images. + The Logical Resource Dynamic Reconfiguration (LRDR) option deals with + logical rather than physical resources. These logical resources are already + physically installed (dynamic installation/removal of these resources, if + supported, is managed via the Hardware Management Console (HMC) or Service + Focal Point (SFP)). As such, the OS does not manage either connector power + or DR visual indicators. Logical connector power domains are specified as + “hot pluggable” (value -1) and DR visual indicators are not + defined for logical connectors. + The device tree contains logical resource DR connectors for the + maximum number of resources that the platform can allocate to the specific + OS. In some cases such as for processors and PHBs, this may be the maximum + number of these resources that the platform supports even if there are + fewer than that currently installed. In other cases, such as memory regions + in a LPARed system, the number may be limited to the amount of memory that + can be supported without resizing the cpu page frame table. The OS may use + the + get-sensor-state RTAS call with the dr-entity-sense + token to determine if a given drc-index refers to a connector that is + currently usable for DR operations. If the connector is not currently + usable the return state is “DR entity unusable” (2). A + set-indicator (isolation state) RTAS call to an + unusable connector or (dr-indicator) to any logical resource connector + results in a “No such indicator implemented” return + status. + Two allocation models are supported. In the first, resources are + specifically assigned to one and only one partition at a time by the HMC. + In this model, a DR entity state is changed from unusable to usable only by + firmware in response to HMC requests to explicitly move the allocation of + the resource between partitions. In the second model, certain resources may + “float” between cooperating partitions, a partition issues a + set-indicator (allocation state usable) RTAS call and + if the resource is free, the firmware assigns the resource to the + requesting partition and returns the success status. + Set-indicator returns the code + “no-such-indicator” if either the resource is not free, or the + platform is operating in the first model. To return a resource to the + platform firmware, the OS issues a + set-indicator (allocation state unusable) RTAS call for + the resource’s DR connector. + +
+ Platform Requirements for LRDR + The following requirements apply to the hardware and/or firmware as + a result of implementing LRDR on a platform. + + + + R1--1. + + For the LRDR option: The hardware must provide the + capability to power-cycle any hardware that is going to be switched + between partitions as part of LRDR, if that hardware requires + power-cycling to put the hardware into a known state (for example, PCI + IOAs). + + Architecture Note: Except for PCI Express IOAs that + implement the Function Level Reset (FLR) option, since the PCI + architecture is not specific as to the state of the IOA when the IOAs + reset is activated and deactivated, either the platform designer will + need to guarantee that all logic in all IOAs (including any internal + storage associated with the IOA) is cleared to a known state by use of + the IOAs' reset, or else the platform will need to provide the capability + to power-cycle those IOAs, including the integrated ones (that is, + including the non-pluggable ones). Also note that hardware which requires + power-cycling to initialize may impact the capability to reliably reboot + an OS, independent of whether or not LRDR is implemented. + + + + + R1--2. + + For the LRDR option: + Any power-cycling + of the hardware which is done by the platform during an LRDR operation + (for example, as part of an ibm,configure-connector operation), must be + functionally transparent to the software, except that PCI plug-in cards + that are plugged into a PCI Hot Plug DR connector do not need to be + powered on before the + ibm,configure-connector call for a logical SLOT DR + connector returns to the caller. + + Architecture Note: PCI plug-in cards that are plugged + into a DR connector will not be configured as part of an + ibm,configure-connector operation on a logical DR connector of type SLOT + above the plug-in card (see section 17.6.3.3 ibm,configure-connector). + However, Requirement + does require a PCI IOA which is + not plugged in to a PCI Hot Plug DR connector (for example, soldered on + the planar) be powered up and configured as a result of an + ibm,configure-connector operation on a logical DR connector of type SLOT + above such an IOA, and requires this powering up to be functionally + transparent to the caller of ibm,configure-connector operation (a longer + busy time is not considered to be a violation of the functional + transparency requirement). + + + +
+ +
+ DR Properties for Logical Resources + Logical resource dynamic reconfiguration is a special case of + general DR, therefore, certain DR properties take on special + values. + + DR Property Values for Logical Resources + + + + + + + + Property Name + + + + + Property Value + + + + + + + + + “ibm,drc-indexes” + + + + As defined in + . + + + + + + “ibm,my-drc-index” + + + + As defined in + . + + + + + + “ibm,drc-names” + + + + As defined in + . + Note: + This name + allows for correlation between the OS and HMC user + interfaces. + + + + + + “ibm,drc-power-domains” + + + + Logical Resource connectors are defined to be “hot + pluggable” having a domain value of -1 per definition in + . + + + + + + “ibm,drc-types” + + + + Shall be one of the values “CPU”, + “MEM”, “PHB”, or “SLOT” as + defined in + . + + + + +
+ + + + R1--1. + + For the LRDR option: All platform requirements of the + base DR option architecture must be met ( + ). + + + + + R1--2. + + For the LRDR option: The + /cpus OF device tree node must include + “ibm,drc-types” (of type CPU), + “ibm,drc-power-domains” + (of value -1), + “ibm,drc-names”, and + “ibm,drc-indexes” + properties with entries for each potentially + supported dynamically reconfigurable processor. + + + + + R1--3. + + For the LRDR option: The root node of the OF device + tree must include + “ibm,drc-types” + (of type MEM), + “ibm,drc-power-domains” + (of value -1), + “ibm,drc-names”, and + “ibm,drc-indexes” + properties with entries for each potentially + supported dynamically reconfigurable memory region. + + + + + R1--4. + + For the LRDR option: The root node of the OF device + tree must not include any drc properties ( + “ibm,drc-*”) for the base memory region + (reg value 0). + + + + + R1--5. + + For the LRDR option: The root node of the OF device + tree must include + “ibm,drc-types” + (of type PHB), + “ibm,drc-power-domains” + (of value -1), + “ibm,drc-names”, and + “ibm,drc-indexes” + properties with entries for each potentially + supported dynamically reconfigurable PHB. + + + + + R1--6. + + For the LRDR option: The + /pci OF device tree node representing a PHB must + include + “ibm,drc-types” + (of type SLOT), + “ibm,drc-power-domains” + (of value -1), + “ibm,drc-names”, and + “ibm,drc-indexes” + properties with entries for each potentially + supported dynamically reconfigurable PCI SLOT. + + + + + R1--7. + + For the LRDR option: platforms must implement the + allocation-state indicator 9003, as defined in + . + + + + + R1--8. + + For the LRDR option: For memory LRDR, the + “ibm,lrdr-capacity” property must be + included in the + /rtas node of the partition device tree (see + ). + + + +
+ +
+ Architectural Intent -- Logical DR Sequences: + This architecture is designed to support the logical DR sequences + specified in the following sections. See also + . + +
+ Acquire Logical Resource from Resource Pool + + + + The OS responds to some stimuli (command, workload manager, HMC, + etc.) to acquire the resource, perhaps using the + “ibm,drc-names” value as a reference if a + human interface is involved. + + + + The OS determines + if the resource is usable: + + + + OS uses + get-sensor-state (dr-entity-sense) to determine the + state of the DR connector + + + + If the state is “unusable” the OS issues + set-indicator (allocation-state, usable) to attempt + to allocate the resource. Similarly, if the state is “available for + exchange” the OS issues + set-indicator (allocation-state, exchange) to attempt + to allocate the resource, and if the state is “available for + recovery” the OS issues + set-indicator (allocation-state, recover) to attempt + to allocate the resource. + + + + If successful, continue, else return error status to the + requester. If successful, this is the point where the resource is + allocated to the OS. + + + + + + Continue with DR operation. + + + + The OS unisolates the resource via + set-indicator (isolation-state, unisolate). This is + the point where the OS takes ownership of the resource from the platform + firmware and the firmware removes the resource from its resource + pool. + + + + The OS configures the resource using + ibm,configure-connector RTAS. + + + + The OS incorporates the resource into its resource pool. + + + + If the resource is a processor, the OS must use the + start-cpu RTAS call to move the processor from the + stopped state (at the end of the + ibm,configure-connector) to the running + state. + + + + + + The OS returns status of operation to the requester. + + + + + + The OS notifies requesting entity of the OS state relative to + the resource acquisition. + + +
+ +
+ Release Logical Resource + + + + Some entity (System administrator commanding from the HMC, a + workload manager, etc.) requests the OS to release the resource using the + “ibm,drc-names” value as a + reference. + + + + The OS attempts to stop using logical resource. + + + + If the resource is a processor, the OS calls the + stop-self RTAS call then waits for the processor to + enter the stopped state using the RTAS + query-cpu-stopped-state call. + + + + The OS isolates the resource via + set-indicator (isolation-state, isolate). + + + + Unless the isolated resource was the partition’s last + processor, the OS deallocates the resource via + set-indicator (allocation-state, unusable). This is + the point where the platform firmware takes ownership of the resource + from the OS. That is, the OS removes the resource from its resource pool + and the firmware adds it to the firmware resource pool. + + + + + + The OS returns status of operation to the requester. + + + + + + The OS unallocates the resource by + set-indicator (allocation-state, unusable). + + + + The system administrator may command the HMC to allocate the + logical resource to another partition (LPAR) or reserved pool + (COD). + + + + Any needed hardware removal is handled by HMC/SPC. + + +
+
+ +
+ RTAS Call Semantics/Restrictions + This section describes the unique application of DR RTAS functions + to the dynamic reconfiguration of logical resources. + +
+ <emphasis>set-indicator</emphasis> (isolation-state, isolate) + Dynamic reconfiguration of logical resources introduces special + meaning and restrictions to the DR connector isolation function depending + upon the logical resource being isolated. + +
+ Isolation of CPUs + The isolation of a CPU, in all cases, is preceded by the + stop-self RTAS function for all processor threads, + and the OS insures that all the CPU’s threads are in the RTAS + stopped state prior to isolating the CPU. Isolation of a processor that + is not stopped produces unpredictable results. The stopping of the last + processor thread of a LPAR partition effectively kills the partition, and + at that point, ownership of all partition resources reverts to the + platform firmware. + + + + R1--1. + + For the LRDR option: Prior to issuing the RTAS + set-indicator specifying isolate isolation-state of a + CPU DR connector type, all the CPU threads must be in the RTAS stopped + state. + + + + + R1--2. + + For the LRDR option: Stopping of the last processor + thread of a LPAR partition with the + stop-self RTAS function, must kill the partition, + with ownership of all partition resources reverting to the platform + firmware. + + + +
+ +
+ Isolation of MEM Regions + Isolation of a MEM region creates a paradox if the MEM region being + isolated contains the calling program (there being no program left for + the firmware to return). + + Note: The base memory region (starting at address + zero) is not associated with a MEM DR connector. This means that the base + memory region cannot be isolated. This restriction avoids two fatal + conditions, attempts to isolate the region containing RTAS, and attempts + to isolate the region containing the interrupt vectors. + It is the responsibility of the OS to unmap the addresses of the + MEM region being isolated from both PFT and the TCE tables. When the LRDR + option is combined with the LPAR option, the hypervisor ensures that the + addresses of the MEM region being isolated are unmapped from both the PFT + and TCE tables before successfully completing the isolation of the MEM + region. If any valid mappings are found, the RTAS + set-indicator (isolation-state) does not change the + isolation-state and returns with a + Status-9001 (Valid outstanding translation). + + + + R1--1. + + For the LRDR option: The caller of the RTAS + set-indicator specifying isolate isolation-state of a + MEM DR connector type must not be within the region being + isolated. + + + + + R1--2. + + For the LRDR option combined with the LPAR option: + The RTAS set-indicator specifying isolate isolation-state of a + MEM DR connector type must check that the region is unmapped from both + the partition’s Page Frame Table(s) and any Translation Control + Entries that would reference the memory, else the RTAS routine must + return with a status of + Status-9001 (Valid outstanding translation) and the + isolation-state is not changed. + + + + + + Implementation Note: The algorithm chosen for + implementing Requirement + depends upon the expected + frequency of isolation events. For RAS reasons, they should be seldom. + For load balancing, they may be far more frequent. These methods are + briefly described here: + + + + First pull the corresponding logical address from the + partition’s valid space so setting new translations to the logical + address are not possible. Then wait for any current in flight translation + additions to complete. Followed by either scanning the entire PFT and TCE + tables looking for valid translations or checking a use count for the + particular logical address range. The PFT/TCE table search may be long, + however, it is only done at isolation time. + + + + The use count method must be maintained for each add and remove + of an address translation with the corresponding accessing of a use count + based upon the physical real address of the memory block. + + +
+ +
+ Isolation of PHBs and Slots + An isolation of a PHB naturally disconnects the OS image from any + of the DR connectors downstream of the PHB (specifically any I/O slots + and PCI Hot Plug connectors associated with the PHB). To avoid the + complexity of gracefully managing multi-level isolation, isolation is + restricted to only “leaf” DR connectors, that is connectors + that have no unisolated or usable DR connectors below them. That is, for + logical DR connectors below the connector being isolated, a + get-sensor-state dr-entity-sense needs to return an + unusable (2) and for physical DR connectors below the connector being + isolated, the DR entity needs to be isolated first via + set-indicator (isolation-state, isolate). The OS is + responsible for removing all virtual address mappings to the address + range associated with a logical I/O SLOT before making the RTAS + set-indicator (isolation-state) call that isolates + the SLOT. When the LRDR option is combined with the LPAR option, the + hypervisor ensures that the addresses associated with the logical SLOT + being isolated are unmapped from both the PFT and TCE tables before + successfully completing the isolation of the SLOT connector. If any valid + mappings are found, the RTAS + set-indicator (isolation-state) does not change the + isolation-state and returns with a + Status-9001 (Valid outstanding translation). + + + + R1--1. + + For all LRDR options: If a request to + set-indicator (isolation-state, isolate) would result + in the isolation of one or more other DR connectors which are currently + unisolated or usable, then the + set-indicator RTAS must fail with a return code of + “Multi-level isolation error” (-9000). + + + + + R1--2. + + For the LRDR option combined with the LPAR + option: The RTAS + set-indicator specifying isolate isolation-state of a + SLOT DR connector type must check that the IOA address range associated + with the slot is unmapped from both the partition’s Page Frame + Table(s) and any Translation Control Entries that would reference those + locations, else the RTAS routine must return with a + Status-9001 (Valid outstanding translation) and the + isolation-state is not changed. + + + +
+
+
+ +
+ <emphasis>set-indicator</emphasis> (dr-indicator) + Logical connectors do not have associated dr-indicators (token + value 9002). An attempt to set the state of such an indicator results in + a “No such indicator implemented” return status. + + + + + R1--1. + + For all LRDR options: The calling of + set-indicator with a token value of 9002 + (dr-indicator) and an index representing a logical connector must fail + with a return code of “No such indicator implemented” + (-3). + + + +
+ +
+ <emphasis>ibm,configure-connector</emphasis> + The + ibm,configure-connector RTAS call is used to return + to the OS the device tree nodes and properties associated with the newly + un-isolated logical resources and configure them for use. + The + ibm,configure-connector RTAS call used against a + logical DR connector can encounter other logical DR connectors or + physical DR connectors below it in the tree. If a logical connector is + encountered below a logical connector that is being configured, the + ibm,configure-connector RTAS call will not configure + the sub-tree, if it is not owned by the OS (where owned refers to a DR + connector that would return a DR entity usable, for a + get-sensor dr-entity-sense sensor). If a physical + connector is encountered, then the sub-tree below the physical connector + may or may not be configured, depending on the implementation. + + Architecture Note: The requirements of this section + specify the minimum sub-tree contents returned for various connector + types. Implementations may optionally return other valid previously + reported nodes that represent the current configuration of the device + tree. Previously reported nodes may not have any changes from their + previously reported state. A node that was removed from the configuration + due to a DR operation and returns due to a subsequent DR operation is not + considered to have been previously reported. It is the caller's + responsibility to recognize previously reported nodes. + + + + R1--1. + + For all LRDR options: If a request to + ibm,configure-connector specifies a connector that is + isolated, + ibm,configure-connector must immediately return + configuration complete. + + + + + R1--2. + + For all LRDR options: If the connector index refers + to a connector that would return a “DR entity unusable” + status (2), “DR entity available for exchange” status (3), or + “DR entity available for recovery” status (4) to the + get-sensor dr-entity-sense token, the + ibm,configure-connector RTAS call must return + “-9003: Cannot configure - Logical DR connector unusable, available + for exchange, or available for recovery” on the first call without + any configuration action taken on the DR connector. + + + + + R1--3. + + For all LRDR options: If a request to + ibm,configure-connector specifies a connector of type + CPU, + the returned sub-tree must consist of the specific + cpu-node, its children, and any referenced nodes that had not been + previously reported (such as L2 and L3 caches etc.) all containing the + properties as would be contained in those nodes had they been available + at boot time. + + Implementation Note: Future platforms that support + concurrent maintenance of caches, will require that high level cache + nodes (L2, L3 etc.) are added by + ibm,configure-connector such that their properties + can change as new/repaired hardware is added to the platform. Therefore, + it is the OS's responsibility when isolating a CPU to purge any + information it may have regarding an orphaned high level cache node. The + OS may use the + “ibm,phandle” property to selectively + remove caches when a processor is removed. The platform considers any + high level cache that is newly referenced (reference count for this + partition goes from 0 to 1) to have been previously unreported. + + + + + R1--4. + + For all LRDR options: If a request to + ibm,configure-connector specifies a connector of type + MEM, + the returned sub-tree must consist of the specific + ibm,memory-region node containing the properties as + would be contained in that node had it been available at boot + time. + + + + + R1--5. + + For all LRDR options: If a request to + ibm,configure-connector specifies a connector of type + PHB or SLOT, then all of the following must be true: + + + The returned values must represent the sub-tree for the specific + I/O sub-system represented by the connector, except for entities below + any DR connectors (logical or physical) which are below the connector + which is the target of the ibm,configure-connector operation (that is, + the ibm,configure-connector operation stops at any DR connector). + + + + The sub-tree must consist of the specific node and its children + all containing the properties as would be contained in those nodes had + they been available at boot time, including (if they exist) built-in PCI + IOAs. + + + + + + + + R1--6. + + For all LRDR options: If a request to + ibm,configure-connector specifies a connector of type + SLOT, + the returned values must represent the sub-tree for + the specific I/O sub-system represented by the SLOT connector, and the + sub-tree must consist of the specific + /pci node and its children all containing the + properties as would be contained in those nodes had they been available + at boot time, except for the PCI IOA nodes assigned to the OS image that + contain the same properties as they would following a PCI hot plug + operation (see + ). + + + + + R1--7. + + For all LRDR options: If a platform implementation + powers-up and configures physical DR entities in the sub-tree under a + logical DR connector, then a request to + ibm,configure-connector of the logical DR connector + must use the return status of 990x from the + ibm,configure-connector call, as necessary, during + the DR entity power-up sequence(s) and must control any power-up and + sequencing requirements, as would be done by the platform during platform + power-up. + + + + +
+
+ diff --git a/Virtualization/ch_lpar_option.xml b/Virtualization/ch_lpar_option.xml new file mode 100644 index 0000000..019471f --- /dev/null +++ b/Virtualization/ch_lpar_option.xml @@ -0,0 +1,18584 @@ + + Logical Partitioning Option + +
+ Overview + The Logical PARtitioning option (LPAR) simultaneously runs one or + more copies of a single OS or multiple heterogeneous LoPAR compliant OSs + on a single LoPAR platform. A partition, within which an OS image runs, is + assigned a non-overlapping sub-set of the platform’s resources. These + platform-allocatable resources include one or more architecturally distinct + processors with their interrupt management area, regions of system memory, + and I/O adapter bus slots. Partition firmware loaded into each partition + generates an OF device tree to represent the resources of the partition to + the OS image. Allocatable resources are directly controlled by an OS. This + architecture restricts the sharing of allocatable resources between + partitions; to do so requires the use of optional facilities presented in + . Platform resources, other than + allocatable resources mentioned above, that are represented by OF nodes in + the device tree of more than one partition (for example, memory controllers + and processor host bridges) are marked ‘used-by-rtas’. + Since one of the main purposes of partitioning is isolation of the + OSs, the ability to manage real system resources that are common to all + partitions is modified for the LPAR option. This means that partition use + of RTAS functions which ostensibly use real system resources such as power + and time-of-day clocks are buffered from actual manipulation of those + resources. The RTAS is modified for LPAR, and has hypervisor support, to + virtualize real resources for the partitions. Operational management of the + platform moves to a Hardware Management Console (HMC) which is an + application, either local or remote, that manages platform resources with + messages to the hypervisor rather than being under direct control of a + partition’s OS. + Platforms supporting LPAR, contain Power PC processors that support + the hypervisor addressing mode, in which the physical address is equal to + the effective address and all processor resources are available. The + “Real Mode” addressing mode, in these processors, is redefined + to translate and limit the physical addresses that the processor can access + and to restrict access to certain address translation controlling processor + resources. The virtual addressing mode is unchanged. See the + (level 2.0 and beyond) for the + architecture extensions required for the processor. + The I/O subsystems of these platforms contain I/O bridges that + restrict the bus addresses that I/O adapters can access. These restricted + bus addresses are subsequently translated through the Translation Control + Entry (TCE) mechanism to restrict Direct Memory Accesses (DMAs) by I/O + devices. This restriction is to system memory allocated to a partition and + managed by the OS image owning the device. The interrupt subsystem of these + platforms is enhanced with multiple (one per partition) global interrupt + queues to direct interrupts to any processor assigned to the I/O + adapter’s owning OS image. + Logical Partitioning platforms employ a unique firmware component + called the hypervisor (that runs in hypervisor mode) to manage the address + mapping and common platform hardware facilities, thereby ensuring isolation + between partitions. The OS uses new hypervisor interfaces to manage the + partition’s page frame and TCE tables. The platform firmware utilizes + implementation dependent interfaces to platform hardware common to all + partitions. Thus, a system with LPAR has different OS support than a system + without LPAR. + In addition to generating per partition device trees, the OF + component of a logically partitioned platform manages the initial booting + and any subsequent booting of the specific OS image associated with each + partition. + The NVRAM of a platform contains configuration variables, policy + options, and working storage that is protected from accesses that might + adversely affect one or more partitions and their OS images. The hypervisor + firmware component restricts an OS image’s access to NVRAM to a + region assigned to its partition. This may restrict the number of + partitions. + Most system management on systems without LPAR is performed by OS + based applications that are given access to modify the platform’s + configuration variables, policy options and firmware flash. For various + Reliability Availability and Serviceability (RAS) reasons, LoPAR Logical + Partitioning platforms do not restrict platform operational management + functions to applications running on a preferred partition or OS image. + Access to these Operational Management facilities is provided via a Support + Processor communication port that is connected to an HMC and/or through a + communications port that is connected through a PCI adapter in a partition. + The HMC is a set of applications running in a separate stand-alone platform + or in one of the platform’s partitions. These HMC applications are + required to establish the platform’s LPAR configuration, however, the + configuration is stored in the platform and, therefore, the HMC is not + required to boot or operate the platform in a pre-configured non-error + condition. + +
+ Real Mode Accesses + When the OS controlling an LPAR runs with address translation + turned off (MSRDR or MSRIR + bit(s) =0) (real mode) the LPAR hardware + translates the memory addresses to an LPAR unique area known as the Real + Mode Area (RMA). When control is initially passed to the OS from the + platform, the RMA starts at the LPAR's logical address 0 and is the first + logical memory block reported in the LPAR’s device tree. In + general, the RMA is a subset of the LPAR's logical address space. + Attempting a non relocated access beyond the bounds of the RMA results in + an storage interrupt (ISI/DSI depending upon instruction or data + reference). The RMA hardware translation scheme is platform dependent. + The options are given below. + +
+ Offset and Limit Registers + The Offset RMA architecture checks the LPAR effective address + against the contents of an RMOL register allowing the access, after + adding an LPAR specific offset to form the real address, if the effective + address is less, else signaling a protection exception. +
+ +
+ Reserved Virtual Addresses + The platform may map the RMA through the hashed paged table via a + reserved range of virtual addresses. This mapping from the effective + address is done by setting the high order virtual address bits + corresponding to the VSID to the 0b00 || 0x001FFFFFF 1 TB VSID value. + This virtual address is then translated as other virtual addresses. If + the effective address is outside the bounds of the RMA, the storage + interrupt signals a PTEG miss. The platform firmware prepopulates the + LPAR's page frame table with “bolted” entries representing + the real storage blocks that make up the RMA. Note, this method allows + for the RMA to be discontiguous in real address space. The Virtualized + Real Mode Area (VRMA) option gives the OS the ability to dynamically + relocate, expand, and shrink the RMA. See + for more details. +
+
+ +
+ General LPAR Reservations and Conventions + This section documents general LPAR reserved facilities and + conventions. Other sections document reserved facilities and conventions + specific to the function they describe. + + + + R1--1. + + For the LPAR option: To avoid conflict with the + platform’s reserved addresses, the OS must not use the 1 TB (SLB + and PTE B field equal to one) 0b00 || 0x001FFFFFF VSID for purposes other + than virtualizing the RMA. + + + + + R1--2. + + For the LPAR option: In order to avoid a storage + exception, the OS must not remove PTEs marked with the + “bolted” indicator (PTE bit 59 = 1) unless the virtual + address space can be referenced by another PTE or the OS does not intend + to access the virtual address space. + + + + + R1--3. + + For the LPAR option: To avoid conflict with the + platform’s hypervisor, the OS must be prepared to share use of + SPRG2 as the interrupt scratch register whenever an hcall() is made, or a + machine check or reset interrupt is taken. + + + + + R1--4. + + For the LPAR option: If the platform virtualizes the + RMA, prior to transferring control to the OS, the platform must select a + page size for the RMA such that the platform uses only one page table + entry per page table entry group to virtualize the RMA. + + + + + R1--5. + + For the LPAR option: If the platform virtualizes the + RMA, prior to transferring control to the OS, the platform must use only + the last page table entry of a page table entry group to virtualize the + RMA. + + + + +
+
+ +
+ Processor Requirements + + + + R1--1. + + For the LPAR option: The platform processors must + support the Logical Partitioning (LPAR) facilities as defined in + (Version 2.0 or later). + + + + +
+ +
+ I/O Sub-System Requirements + The platform divides the I/O subsystem up into Partitionable + Endpoints (PEs). See + for more information on PEs. Each PE has + its own (separate) error, addressing, and interrupt domains which allows + the assignment of separate PEs to different LPAR partitions. + The following are the requirements for I/O subsystems when the + platform implements LPAR. + + + + R1--1. + + For the LPAR option: The platform must provide methods + and mechanisms to isolate IOA and I/O bus errors from one PE from affecting + another PE, from affecting a partition to which the PE is not given access + authority by the platform, and from affecting system resources such as the + service processor which are shared between partitions, and must do so with + the EEH option programming model. + + + + + R1--2. + + For the LPAR option: + The platform must enable the EEH option for all PEs by default. + Software and Firmware Implementation Notes: For the + platform (versus the OS or device driver) to enable EEH, there must be some + assurance that the device drivers are EEH aware, if not EEH enabled. For + example, the device driver or OS may signal its awareness by using + ibm,set-eeh-option RTAS call to enable EEH prior to a + configuration cycle via the + ibm,write-pci-config RTAS call which enables the Memory + Space or IO Space enable bits in the PCI Command register, and firmware can + ignore the + ibm,write-pci-config RTAS call which enables the Memory + Space or IO Space enable bits for an IOA if EEH for that IOA has not been + enabled first. To be EEH aware, a device driver does not need to be able to + recover from an MMIO Stopped and DMA Stopped state, only recognize the + all-1's condition (from a + Load from its IOA or on a PCI configuration read from + its IOA) and not use data from operations that may have occurred since the + last all-1's checkpoint. In addition, the device driver under such failure + circumstances needs to turn off interrupts (using the + ibm,set-int-off RTAS call, or for conventional PCI and + PCI-X infrastructures only: by resetting the IOA and keeping it reset with + ibm,set-slot-reset or + ibm,slot-error-detail) to make sure that any + (unserviceable) interrupts from the IOA do not affect the system (MSIs are + blocked by the EEH DMA Stopped State, but LSIs are not). Note that if + all-1’s data may be valid, the + ibm,read-slot-reset-state2 RTAS call should be used to + discover the true EEH state of the device. + + + + + R1--3. + + For the LPAR option: The platform must assign a PE to + one and only one partition at a time. + + + + + R1--4. + + For the LPAR option: + The platform must limit the DMA addresses accessible to a PE to the address ranges assigned + to the partition to which the PE is allocated, and, if the PE is used to + implement a VIO device, then also to any allowed redirected DMA address + ranges. + + Architecture and Implementation Notes: + + + Platforms which do not implement either Requirement + or Requirement + require PE granularity of + everything below the PHB, resulting in poor LPAR partition I/O assignment + granularity. + + + + Requirement + has implications in preventing access to both to I/O address + ranges and system memory address ranges. That is, Requirement + + + requires prevention of peer to peer operations from one IOA to + another IOA when those IOA addresses are not owned by the same partition, + as well as to providing an access protection mechanism to protect system + memory. Note that relative to peer to peer operations, some bridges or + switches may not provide the capabilities to limit peer to peer, and the + use of such bridges or switches require the limitation that all IOAs under + such bridges or switches be assigned to the same partition. + + + + + + + + R1--5. + + For the LPAR option: The platform must + provide a PE the capability of accessing all of the System Memory addresses + assigned to the partition to which the PE is allocated. + + + + + R1--6. + + For the LPAR option: If TCEs are used to satisfy + Requirements + , and + , then the platform must provide + the capability to map simultaneously and at all times at least 256 MB for + each PE. + + + + + R1--7. + + For the LPAR option: If TCEs are used to satisfy + Requirements + , and + , then the platform must prevent + any DMA operations to System Memory addresses which are not translated by + TCEs. + + + + + R1--8. + + For the LPAR option: The DMA address range accessible + to a PCI IOA on its I/O bus must be defined by the + “ibm,dma-window” property in its + parent’s OF device tree node. + Platform Implementation Note: To maximize the ability to migrate + memory pages underneath active DMA operations, when ever possible, a bridge + should create a bus for a single IOA and either its representing bridge + node should include the + “ibm,dma-window” property specific for the + IOA for conventional PCI or PCI-X IOAs or the IOA function nodes should + contain the + “ibm,my-dma-window” property specific for + the IOA function for PCI Express IOAs. When the configuration of a bus + precludes memory migration, the platform may combine the DMA address for + multiple IOAs that share a bus into a single + “ibm,dma-window” property housed in the + bridge node representing the bridge that creates the shared bus. + + + + +
+ +
+ Interrupt Sub-System Requirements + + + + R1--1. + + For the LPAR option: The platform must + not assign the same interrupt (LSI or MSI) or same interrupt source number + to different PEs (interrupts cannot be shared between partitions). + + + + + R1--2. + + For the LPAR option: The interrupt presentation layer + must support at least one global interrupt queue per platform supported + partition. + + + + + R1--3. + + For the LPAR option: The interrupt presentation layer + must separate the per processor interrupt management areas into a separate + 4 K pages per processor so that they can each be individually protected by + the PTE mechanism and assigned to their respective assigned + partitions. + + + + + R1--4. + + For the LPAR option: The platform must restrict the + processors that service a global queue to those assigned to a single + partition. + + + + + R1--5. + + For the LPAR option: If the interrupt source layer + supports message signaled interrupts, the platform must isolate the PCI + Message interrupt Input Port (PMIP) in its own 4 K page of the + platform’s address space. + + + + + R1--6. + + For the LPAR option: If the interrupt source layer + supports message signaled interrupts, the hardware must ignore all writes + to the PMIP’s 4 K page except those to the PMIP itself. + + + + + R1--7. + + For the LPAR option: If the interrupt source layer + supports message signaled interrupts, the hardware must return all ones on + reads of the PMIP’s 4 K page except those to the PMIP itself. + Signalling a machine check interrupt to the affected processor on a read + that returns all 1s as above is optional. + + + + + R1--8. + + For the LPAR option: The interrupt source layer must + support a means in addition to the inter-processor interrupt mechanism for + the hypervisor to signal an interrupt to any processor assigned to a + partition. + + Software Note: While firmware takes all reasonable + steps to prevent it, it may be possible, on some hardware implementations, + for an OS to erroneously direct an individual IOA’s interrupt to + another partition’s processor. An OS supporting LPAR should ignore + such “Phantom” interrupts. + + + + +
+ +
+ Hypervisor Requirements + The purpose of the hypervisor is to virtualize the facilities of + platforms, with LPAR, such that multiple copies of a LoPAR compliant OS + may simultaneously run protected from each other in different logical + partitions of the platform. That is, the various OS images may, without + explicit knowledge of each other, boot, run applications, handle exceptions + and events and terminate without affecting each other. + The hypervisor is entered by way of three interrupts: the System + Reset Interrupt, the Machine Check Interrupt and System (hypervisor) Call + Interrupt. These use hypervisor interrupt vectors 0x0100, 0x0200, and + 0x0C00 respectively. In addition, a processor implementation dependent + interrupt, at its assigned address may cause the hypervisor to be entered. + The return from the hypervisor to the OS is via the rfid (Return from + Interrupt Doubleword) instruction. The target of the rfid (instruction at + the address contained in SRR0) is either a firmware glue routine (in the + case of System Reset or Machine Check) or the instruction immediately + following the invoking hypervisor call. The reason for the firmware glue + routines is that the OS must do its own processing because of the + asynchronous nature of System Reset or Machine Check interruptions. The + firmware glue routine calls an OS registered recovery routine for the + System Reset or Machine Check condition for further details see (reference + to recoverable machine check ACR material to be added when available). The + glue routines are registered by the partition’s OS through RTAS. + Until the glue routines are registered, the OS does not receive direct + reports of either System Reset or Machine Check interrupts but is simply + re-booted by the hypervisor. The glue routines contain a register buffer + area that the hypervisor fills with register values that the glue routine + must pass to the OS when calling the interrupt handler. The last element in + this buffer is a lock word. The lock word is set with the value of the + using processor, and reset by the glue routine just before calling the OS + interrupt handler. This way only one buffer is needed per partition rather + than one per processor. + At the invocation of the hypervisor, footprint records are generated + for recovery conditions. Machine Check and Check Stop conditions are, in + some cases, isolatable to the affected partition(s). In these cases, the + hypervisor can then prove that it was not executing changes to the global + system tables on the offending processor when the error occurred. If this + cannot be proven, the global state of the complex is in doubt and the error + cannot be contained. It is anticipated that check stops that only corrupt + the internal state of the affected processor, stop that processor only. + When the service processor subsequently notices the stopped processor it + notifies one of the other processors in the partition through a simulated + recoverable machine check. The hypervisor running on the notified processor + then takes appropriate action to log out and restart the partition, or if + there is an alternate cpu capability, then continue execution with a + substitute for the stopped processor. + The following table presents the functions supplied by the + hypervisor. + Architecture Note: Some functions performed by partition firmware (OF + and RTAS) require hypervisor assist, but those firmware implementation + dependent interfaces do not appear in this document. + + + Architected hcall()s + <emphasis>(Continued)</emphasis> + + + + + + + + Function Name/Section + + + + + Comments + + + + + + + + + / + + + + Removes a PTE from the partition’s node Page Frame + Table + + + + + + / + + + + Removes up to four (4) PTEs from the partition’s node + Page Frame Table + + + + + + / + + + + Inserts a PTE into the partition’s node Page Frame + Table + + + + + + / + + + + Reads the specified PTE from the partition’s node + Page Frame Table + + + + + + / + + + + Clears the Modified bit in the specified PTE in the + partition’s node Page Frame Table + + + + + + / + + + + Clears the Referenced bit in the specified PTE in the + partition’s node Page Frame Table + + + + + + / + + + + Sets the Page Protection and Storage Key bits in the + specified PTE in the partition’s node Page Frame + Table + + + + + + / + + + + Returns the value of the specified DMA Translation Control + Entry + + + + + + / + + + + Inserts the specified value into the specified DMA + Translation Control Entry + + + + + + / + + + + Inserts the specified value into multiple DMA Translation + Control Entries + + + + + + / + + + + Inserts a list of values into the specified range of DMA + Translation Control Entries + + + + + + / + + + + SPRG0 is architecturally a hypervisor resource. This call + allows the OS to write the register. + + + + + + / + + + + DABR is architecturally a hypervisor resource. This call + allows the OS to write the register. + + + + + + / + + + + Initializes pages in real mode either to zero or to the + copied contents of another page. + + + + + + / + + + + Manage the Extended DABR facility. + + + + + + / + + + + Returns the value contained in a cache inhibited logical + address + + + + + + / + + + + Stores a value into a cache inhibited logical + address + + + + + + / + + + + Returns up to 16 bytes of virtualized console terminal + data. + + + + + + / + + + + Sends up to 16 bytes of data to a virtualized console + terminal. + + + + + + / + + + + Gets a list of possible client Vterm IOA + connections. + + + + + + / + + + + Associates server Vterm IOA to client Vterm IOA. + + + + + + / + + + + Breaks association between server Vterm IOA and client + Vterm IOA. + + + + + + / + + + + Returns internal hypervisor work areas for code + maintenance. + + + + + + / + + + + Generates and End Of Interrupt + + + + + + / + + + + Sets the Processor’s Current Interrupt + Priority + + + + + + / + + + + Generates an Inter-processor Interrupt + + + + + + / + + + + Polls for pending interrupt + + + + + + / + + + + Accepts pending interrupt + + + + + + / + + + + Migrates the page underneath an active DMA + operation. + + + + + + / + + + + Manages the performance monitor facility. + + + + + + / + + + + Registers the virtual processor area that contains the + virtual processor dispatch count + + + + + + / + + + + Makes processor virtual processor cycles available for + other uses (called when an OS image is idle) + + + + + + / + + + + Causes a virtual processor’s cycles to be transferred + to a specified processor. (Called by a blocked OS image to allow + a lock holder to use virtual processor cycles rather than waiting + for the block to clear.) + + + + + + / + + + + Awakens a virtual processor that has ceded its + cycles. + + + + + + / + + + + Returns the partition’s virtual processor performance + parameters. + + + + + + / + + + + Sets the partition’s virtual processor performance + parameters (within constraints). + + + + + + / + + + + Returns the value of the virtual processor utilization + register. + + + + + + / + + + + Polls the hypervisor for the existence of pending work to + dispatch on the calling processor. + + + + + + / + + + + Returns the summation of the physical processor + pool’s idle cycles. + + + + + + / + + + + Register Command/Response Queue + + + + + + / + + + + Frees the memory associated with the Command/Response + Queue + + + + + + / + + + + Controls the virtual interrupt signaling of virtual + IOAs + + + + + + / + + + + Sends a message on the Command/Response Queue + + + + + + / + + + + Loads a Redirected Remote DMA Remote Translation Control + Entry + + + + + + / + + + + Loads a list of Redirected Remote DMA Remote Translation + Control Entries + + + + + + / + + + + Unmaps a redirected TCE that was previously built with + H_PUT_RTCE or H_PUT_RTCE_INDIRECT + + + + + + / + + + + Allows modification of LIOBN Attributes. + + + + + + / + + + + Copies data between partitions as if by TCE mapped + DMA. + + + + + + / + + + + Write parameter data to remote DMA buffer. + + + + + + / + + + + Read data from remote DMA buffer to return + registers. + + + + + + / + + + + Registers the partition’s logical LAN control + structures with the hypervisor + + + + + + / + + + + Releases the partition’s logical LAN control + structures + + + + + + / + + + + Adds receive buffers to the logical LAN receive buffer + pool + + + + + + / + + + + Sends a logical LAN message + + + + + + / + + + + Controls the reception and filtering of non-broadcast + multicast packets. + + + + + + / + + + + Changes the MAC address for an ILLAN virtual IOA. + + + + + + / + + + + Allows modifications of ILLAN Attributes. + + + + + + + + / + + + + Constructs a cookie, specific to the intended client, + representing a shared resource. + + + + + + / + + + + Invalidates a cookie representing a shared resource. + + + + + + / + + + + Maps a shared resource into the client’s logical + address space + + + + + + / + + + + Removes a shared resource from a client’s logical + address space. + + + + + + / + + + + Removes receive buffers of specified size from the logical + LAN receive buffer pool. + + + + + + / + + + + Allows the partition to manipulate or query certain virtual + IOA behaviors. + + + + + + / + + + + Join active threads and return H_CONTINUE to final calling + thread + + + + + + + / + + + + Reactivate a suspended CRQ. + + + + + + / + + + + Change the page mapping characteristics of the Virtualized + Real Mode Area. + + + + + + / + + + + Returns Virtual Partition Memory pool statistics + + + + + + / + + + + Set Memory Performance Parameters + + + + + + / + + + + Get Memory Performance Parameters + + + + + + / + + + + Determine Memory Overcommit Performance + + + + + + / + + + + Register a Sub-CRQ. + + + + + + / + + + + Free a Sub-CRQ. + + + + + + / + + + + Send a message to a Sub-CRQ. + + + + + + / + + + + Send a list of messages to a Sub-CRQ. + + + + + + / + + + + Report the home node associativity for a given virtual + processor + + + + + + / + + + + Get the partition energy management parameters + + + + + + / + + + + Returns hints for activating/releasing resource instances + to achieve the best energy efficiency. + + + + + + / + + + + Registers Subvention Notification Structure + + + + + + / + + + + Get a random number + + + + + + / + + + + Initiate a co-processor operation + + + + + + / + + + + Stop a co-processor operation + + + + + + / + + + + Get Extended Memory Performance Parameters + + + + + + / + + + + Set Processing resource mode + + + + + + / + + + + Search TCE table for entries within a specified + range + + + + +
+ +
+ System Reset Interrupt + Hypervisor code saves all processor state by saving the contents of + one register in SPRG2 (SPRG1 if + ibm,nmi-register-2 was used) (Multiplexing the use of + this resource with the OS). The processor’s stack and data area are + found by processing the Processor Identification Register. + + + + R1--1. + + For the LPAR option: The platform must support + signalling system reset interrupts to all processors assigned to a + partition. + + + + + R1--2. + + For the LPAR option: The platform must support + signalling system reset interrupts individually as well as collectively + to all supported partitions. + + + + + R1--3. + + For the LPAR option: The system reset interrupts + signaled to one partition must not affect operations of another + partition. + + + + + R1--4. + + For the LPAR option: The hypervisor must intercept + all system reset interrupts. + + + + + R1--5. + + For the LPAR option: The platform must implement the + FWNMI option. + + + + + R1--6. + + For the LPAR option: The hypervisor must maintain a + count, reset when the partition’s OS, through RTAS, registers for + system reset interrupt notification, of system reset interrupts signaled + to a partition’s processor. + + + + + R1--7. + + For the LPAR option: Once the partition’s OS + has registered for system reset interrupt notification, the hypervisor + must forward the first and second system reset interrupts signaled to a + partition’s processor. + + + + + R1--8. + + For the LPAR option: The hypervisor must on the third + and all subsequent system reset interrupts signaled to a + partition’s processor invoke OF to initiate the partition’s + reboot policy. + + + + + R1--9. + + For the LPAR option: + The hypervisor must have the capability to receive and handle the system reset + interrupts simultaneously on multiple processors in the same or different + partitions up to the number of processors in the system. + + + + +
+ +
+ Machine Check Interrupt + Hypervisor code saves all processor state by saving the contents of + one register in SPRG2 (SPRG1 if + ibm,nmi-register-2 was used) (Multiplexing the use of + this resource with the OS). The processor’s stack and data area are + found by processing the Processor Identification Register. + The hypervisor investigates the cause of the machine check. The + cause is either a recoverable event on the current processor, or a + non-recoverable event either on the current processor or one of the other + processors in the logical partition. Also the hypervisor must determine + if the machine check may have corrupted its own internal state (by + looking at the footprints, if any, that were left in the per processor + data area of the errant processor. + + + + R1--1. + + For the LPAR option: The hypervisor must have the + capability to receive and handle the machine check interrupts + simultaneously on multiple processors in the same or different partitions + up to the number of processors in the system. + + + + +
+ +
+ Hypervisor Call Interrupt + The hypervisor call (hcall) interrupt is a special variety of the + system call instruction. The parameters to the hcall() are passed in + registers using the PA ABI definitions (Reg 3-12 for parameters). In + contrast to the PA ABI, pass by reference parameters are avoided to or + from hcall(). This minimizes the address translation problem pointer + parameters cause. Some input parameters are indexes. Output parameters, + when generated, are passed in registers 4 through 12 and require special + in-line assembler code on the part of the caller. The first parameter to + hcall() is the function token. + specifies the valid hcall() + function names and token values. Some of the hcall() functions are + optional, to indicate if the platform is in LPAR mode, and which + functions are available on a given platform, the OF property + “ibm,hypertas-functions” is provided in + the /rtas node of the partition’s device tree. The + property is present if the platform is in LPAR mode while its value + specifies which function sets are implemented by a given implementation. + If platform implements any hcall() of a function set it implements the + entire function set. Additionally, certain values of the + “ibm,hypertas-functions” property + indicate that the platform supports a given architecture extension to a + standard hcall(). + The floating point registers along with the FPSCR are in general + preserved across hcall() functions, unless the “Maintain + FPRs” field of the VPA =0, see + . The general purpose registers + r0 and r3-r12, the CTR and XER registers are volatile along with the + condition register fields 0 and 1 plus 5-7. Specific hcall()s may specify + a more restricted “kill set”, refer to the specific hcall() + specification below. + + + + R1--1. + + For the LPAR option: The platform’s + /rtas node must contain an + “ibm,hypertas-functions” property as + defined below. + + + + + R1--2. + + For the LPAR option: If a platform reports in its + “ibm,hypertas-functions” property (see + ) that it supports a function set, then it + must support all hcall()s of that function set as defined in + . + + + + + + Hypervisor Call Function Table + + + + + + + + + + + Hypervisor Call Function + Name/Section + + + + + Hypervisor Call Function + Token + + + + + Hypervisor Call Performance + Class + + + + + Function Mandatory? + + + + + Function Set + + + + + + + + UNUSED + + + 0x0 + + +   + + +   + + +   + + + + + + / + + + + 0x4 + + + Critical + + + Yes + + + hcall-pft + + + + + + / + + + + 0x8 + + + Critical + + + Yes + + + hcall-pft + + + + + + / + + + + 0xC + + + Critical + + + Yes + + + hcall-pft + + + + + + / + + + + 0x10 + + + Critical + + + Yes + + + hcall-pft + + + + + + / + + + + 0x14 + + + Critical + + + Yes + + + hcall-pft + + + + + + / + + + + 0x18 + + + Critical + + + Yes + + + hcall-pft + + + + + + / + + + + 0x1C + + + Critical + + + Yes + + + hcall-tce + + + + + + / + + + + 0x20 + + + Critical + + + Yes + + + hcall-tce + + + + + + / + + + + 0x24 + + + Critical + + + Yes + + + hcall-sprg0 + + + + + + / + + + + 0x28 + + + Critical + + + Yes - if DABR exists + + + hcall-dabr + + + + + + / + + + + 0x2C + + + Critical + + + Yes + + + hcall-copy + + + + + + / + + + + 0x3C + + + Normal + + + Yes + + + hcall-debug + + + + + + / + + + + 0x40 + + + Normal + + + Yes + + + hcall-debug + + + + + + / + + + + 0x54 + + + Critical + + + Yes + + + hcall-term + + + + + + / + + + + 0x58 + + + Critical + + + Yes + + + hcall-term + + + + + + / + + + + 0x60 + + + Normal + + + Yes if enabled by HMC (default disabled) + + + hcall-dump + + + + + + / + + + + 0x64 + + + Critical + + + Yes + + + hcall-interrupt + + + + + + / + + + + 0x68 + + + Critical + + + Yes + + + hcall-interrupt + + + + + + / + + + + 0x6C + + + Critical + + + Yes + + + hcall-interrupt + + + + + + / + + + + 0x70 + + + Critical + + + Yes + + + hcall-interrupt + + + + + + H_XIRR / + + + + 0x74 + + + Critical + + + Yes + + + hcall-interrupt + + + + + + H_XIRR-X / + + + + 0x2FC + + + Critical + + + Yes + + + hcall-interrupt + + + + + + / + + + + 0x78 + + + Normal + + + If LRDR option is implemented + + + hcall-migrate + + + + + + / + + + + 0x7C + + + Normal + + + If performance monitor is implemented + + + hcall-perfmon + + + + + Reserved + + + 0x80 - 0xD8 + + +   + + +   + + +   + + + + + + / + + + + 0xDC + + + Normal + + + If SPLPAR or SLB Shadow Buffer option is + implemented + + + hcall-splpar + SLB-Buffer + + + + + + / + + + + 0xE0 + + + Critical + + + If SPLPAR option is implemented + + + hcall-splpar + + + + + + / + + + + 0xE4 + + + Critical + + + If SPLPAR option is implemented + + + hcall-splpar + + + + + + / + + + + 0xE8 + + + Critical + + + If SPLPAR option is implemented + + + hcall-splpar + + + + + + / + + + + 0xEC + + + Normal + + + If SPLPAR option is implemented + + + hcall-splpar + + + + + + / + + + + 0xF0 + + + Normal + + + If SPLPAR option is implemented + + + hcall-splpar + + + + + + / + + + + 0xF4 + + + Critical + + + If SPLPAR option is implemented + + + hcall-splpar + + + + + + / + + + + 0xF8 + + + Normal + + + If SPLPAR option is implemented + + + hcall-pic + + + + + + / + + + + 0xFC + + + Normal + + + If VSCSI option is implemented + + + hcall-crq + + + + + + / + + + + 0x100 + + + Normal + + + If VSCSI option is implemented + + + hcall-crq + + + + + + / + + + + 0x104 + + + Critical + + + If either the VSCSI or logical LAN option is + implemented + + + hcall-vio + + + + + + / + + + + 0x108 + + + Critical + + + If VSCSI option is implemented + + + hcall-crq + + + + + + / + + + + 0x10C + + + Critical + + + If VSCSI option is implemented + + + hcall-rdma + + + + + + / + + + + 0x110 + + + Critical + + + If VSCSI option is implemented + + + hcall-rdma + + + + + + / + + + + 0x114 + + + Normal + + + If logical LAN option is implemented + + + hcall-lLAN + + + + + + / + + + + 0x118 + + + Normal + + + If logical LAN option is implemented + + + hcall-lLAN + + + + + + / + + + + 0x11C + + + Critical + + + If logical LAN option is implemented + + + hcall-lLAN + + + + + + / + + + + 0x120 + + + Critical + + + If logical LAN option is implemented + + + hcall-lLAN + + + + + + / + + + + 0x124 + + + Critical + + + New designs as of 01/01/2003 + + + hcall-bulk + + + + + + / + + + + 0x128 + + + Critical + + + If VSCSI option is implemented + + + hcall-rdma + + + + + + / + + + + 0x12C + + + Critical + + + If VSCSI option is implemented + + + hcall-rdma + + + + + + / + + + + 0x130 + + + Critical + + + If logical LAN option is implemented + + + hcall-lLAN + + + + + + / + + + + 0x134 + + + Normal + + + If Extended DABR option is implemented + + + hcall-xdabr + + + + + + / + + + + 0x138 + + + Critical + + +   + + + hcall-multi-tce + + + + + + / + + + + 0x13C + + + Critical + + +   + + + hcall-multi-tce + + + + + + / + + + + 0x140 + + + Critical + + +   + + + hcall-multi-tce + + + + + Reserved + + + 0x144 + + +   + + +   + + +   + + + + + Reserved + + + 0x148 + + +   + + +   + + +   + + + + + + / + + + + 0x14C + + + Normal + + + If Logical LAN option is implemented + + + hcall-ILAN + + + + + + / + + + + 0x150 + + + Normal + + + If the Server Vterm option is implemented + + + hcall-vty + + + + + + / + + + + 0x154 + + + Normal + + + If the Server Vterm option is implemented + + + hcall-vty + + + + + + / + + + + 0x158 + + + Normal + + + If the Server Vterm option is implemented + + + hcall-vty + + + + + + / + + + + 0x1C4 + + + Normal + + + If Shared Logical Resource option is Implemented + + + hcall-slr + + + + + + / + + + + 0x1C8 + + + Normal + + + If Shared Logical Resource option is Implemented + + + hcall-slr + + + + + + / + + + + 0x1CC + + + Normal + + + If Shared Logical Resource option is Implemented + + + hcall-slr + + + + + + / + + + + 0x1D0 + + + Normal + + + If Shared Logical Resource option is Implemented + + + hcall-slr + + + + + + / + + + + 0x1D4 + + + Critical + + + If logical LAN option is implemented + + + hcall-lLAN + + + + + + / + + + + 0x1D8 + + + Critical + + + If SPLPAR option is implemented + + + hcall-poll-pending + + + + + Reserved + + + 0x1DC - 0x1E0 + + + Varies + + +   + + +   + + + + + Reserved + + + 0x1E8 - 0x1EC + + +   + + +   + + +   + + + + + Reserved + + + 0x1F0 - 0x23C + + + Varies + + +   + + +   + + + + + + / + + + + 0x240 + + + Normal + + + If LIOBN Attributes are implemented + + + hcall-liobn-attributes + + + + + + / + + + + 0x244 + + + Normal + + + If ILLAN Checksum Offload Support is implemented + If ILLAN Backup Trunk Adapter option is + implemented + + + hcall-illan-options + + + + + Reserved + + + 0x248 + + +   + + +   + + +   + + + + + + / + + + + 0x24C + + + Critical + + + If H_PUT_RTCE is implemented + + + hcall-rdma + + + + + Reserved + + + 0x27C + + +   + + +   + + +   + + + + + Reserved + + + 0x280 + + +   + + +   + + +   + + + + + Reserved + + + 0x28C-0x294 + + +   + + +   + + +   + + + + + + / + + + + 0x298 + + + Normal + + + If Thread Join option is implemented + + + hcall-join + + + + + + + / + + + + 0x2A8 + + + Normal + + + If any virtual I/O options are implemented + + + hcall-vioctl + + + + + + / + + + + 0x2AC + + + Normal + + + If the VRMA option is implemented. + + + hcall-vrma + + + + + + / + + + + 0x2B0 + + + Continued + + + If partition suspension option is implemented + + + hcall-suspend + + + + + Reserved + + + 0x2B4 + + +   + + +   + + +   + + + + + + / + + + + 0x2B8 + + + Normal + + + If the Partition Energy Management Option is + implemented + + + hcall-get-emparm + + + + + + / + + + + 0x2BC + + + Normal + + + If the Cooperative Memory Over-commitment Option is + implemented + + + hcall-cmo + + + + + + / + + + + 0x2D0 + + + Normal + + + If the Cooperative Memory Over-commitment Option is + implemented + + + hcall-cmo + + + + + + / + + + + 0x2D4 + + + Normal + + + If the Cooperative Memory Over-commitment Option is + implemented + + + hcall-cmo + + + + + + / + + + + 0x2D8 + + + Normal + + + If the Cooperative Memory Over-commitment Option is + implemented and the calling partition is authorized. + + + hcall-cmo + + + + + + / + + + + 0x2DC + + + Normal + + + If the Subordinate CRQ Option is implemented + + + hcall-sub-crq + + + + + + / + + + + 0x2E0 + + + Normal + + + If the Subordinate CRQ Option is implemented + + + hcall-sub-crq + + + + + + / + + + + 0x2E4 + + + Normal + + + If the Subordinate CRQ Option is implemented + + + hcall-sub-crq + + + + + + / + + + + 0x2E8 + + + Normal + + + If the Subordinate CRQ Option is implemented + + + hcall-sub-crq + + + + + + / + + + + 0x2EC + + + Normal + + + If the VPHN Option is implemented + + + hcall-vphn + + + + + Reserved + + + 0x2F0 + + +   + + +   + + +   + + + + + + / + + + + 0x2F4 + + + Normal + + + If the Partition Energy Management Option is + implemented + + + hcall-best-energy-1<list> + The <list> suffix for hcall-best-energy indicates + an optional dash delimited series (may be null) of supported + resource codes encoded as ASCII decimal values in addition to + the minimal support value of 1 for processors, other values + are define in + . + + + + + + + / + + + + 0x2F8 + + + Normal + + + If the Expropriation Subvention Notification Option is + implemented + + + hcall-esn + + + + + + X_XIRR-X / + + + + 0x2FC + + + Critical + + + Yes + + + hcall-interrupt + + + + + + / + + + + 0x300 + + + Normal + + + If a random number generator Platform Facilities Option + is implemented + + + hcall-random + + + + + Reserved + + + 0x310 + + +   + + +   + + +   + + + + + + / + + + + 0x304 + + + Normal + + + If one or more Coprocessor Platform Facilities Options + are implemented + + + hcall-cop + + + + + + / + + + + 0x308 + + + Normal + + + If one or more Coprocessor Platform Facilities Options + are implemented + + + hcall-cop + + + + + + / + + + + 0x314 + + + Normal + + + If the Extended Cooperative Memory Overcommittment Option + is implemented + + + hcall-cmo-x + + + + + + / + + + + 0x31C + + + Normal + + + If the platform supports POWER ISA version 2.07 or + higher + + + hcall-set-mode + + + + + Reserved + + + 0x320 + + +   + + +   + + +   + + + + + + / + + + + 0x324 + + + normal + + + If the plaform implements the LRDR option at LoPAR + Version 2.7 or higher + + + hcall-xlates-limited + + + + + Reserved for platform-dependent hcall()s / + + + + 0xF000 - 0xFFFC + + +   + + +   + + +   + + + + + ILLEGAL + + + Any token value having a one in either of the low order + two bits + + +   + + +   + + +   + + + + + Reserved + + + 0x328 - 0xEFFC and 0x10000 - 0xFFFFFFFF-FFFFFFFC: RTAS + implementations may assigns values in these ranges to their own + internal interfaces, as long as they are prepared for the + growth of architected functions into this range. + + +   + + +   + + +   + + + + +
+ Firmware Implementation Note: The assignment of function tokens is + designed such that a single mask operation can validate that the value is + within the range of a reasonable size branch table. Entries within the + branch table can handle unimplemented code points. + The hypervisor routines are optimized for execution speed. In some + rare cases, locks are taken, and specific hardware designs require short + wait loops. However, if a needed resource is truly busy, or processing is + required by an agent, the hypervisor returns to the caller, either to + have the function retried or continued at a later time. The Performance + Class establishes specific performance requirements against each specific + hcall() function as defined below. + Hypervisor Call Performance Classes: + Critical Must make continuous forward progress, encountering any + busy resource must cause the function to back out and return with a + “hardware busy” return code. When subsequently called, the + operation begins again. Short loops for larwx and stwcx to acquire an + apparently unheld lock are allowed. These functions may not include wait + loops for slow hardware access. + Normal Similar to critical, however, wait loops for slow hardware + access are allowed. These functions may not include wait loops for an + agent such as an external micro-processor or message transmission + device. + Continued This class of functions is expected to serialize on the + use of external agents. If the external agent is busy the function + returns “hardware busy”. If the interface to the external + agent is not busy, the interface is marked busy and used to start the + function. The function returns one of the “function in + progress” return codes. Later, the caller may check on the + completion of the function by issuing the “check” Hcall + function with the “function in progress” parameter code. If + the function completed properly, the hypervisor maintains no status and + the “check” Hcall returns success. If the operation is still + in process, the same “function in progress” code is returned. + If the function completed in error, the completion error code is + returned. The hypervisor maintains room for at least one outstanding + error status per external agent interface per processor. If there is no + room to record the error status, the hypervisor returns “hardware + busy” and does not start the function. + Terminal This class of functions is used to manage a partition when + the OS is not in regular operation. These events include postmortems and + extensive recoveries. + The hypervisor performance classes are ordered in decreasing + restriction. + + + + R1--3. + + For the LPAR option: The caller must perform properly + given that the hypervisor meets the performance class specified. + + + + + R1--4. + + For the LPAR option: The hypervisor implementation + must meet the specified performance class or higher. + + + + + R1--5. + + For the LPAR option: Platform hardware designs must + take the allowable performance classes into account when choosing the + hardware access technology for the various facilities. + + + + + R1--6. + + For the LPAR option: The hypervisor must have the + capability to receive and handle the hypervisor call interrupts + simultaneously on multiple processors in the same or different partitions + up to the number of processors in the system. + + + + + R1--7. + + For the LPAR option: The hypervisor must check the + state of the MSR register bits that are not set to a specific value by + the processor hardware during the invoking interrupt per + . + + + + + + MSR State on Entrance to Hypervisor + + + + + + + + + + MSR Bit + + + + + Required State + + + + + Error-Code + + + + + + + + HV - Hypervisor + + + 1 + + + None + + + + + Bits 2,4:46, 57, and 60 Reserved + + + Set to 0 by Hardware + + + None + + + + + ILE - Interrupt Little Endian + + + As Last set by the hypervisor + + + None + + + + + ME - Machine check Enable + + + As last set by the hypervisor + + + None + + + + + LE Little-Endian Mode + + + 0 forced by ILE + + + None + + + + +
+ + + + R1--8. + + For the LPAR option: The Hcall() flags field must + meet the definition in: + ; the hypervisor may safely + ignore flag field values not explicitly defined by the specific hcall() + semantic. + + + + + R1--9. + + For the LPAR option: The platform must ensure that + flag field values not defined for a specific hcall() do not compromise + partitioning integrity. + + + + + R1--10. + + For the LPAR option: Implementations that normally + choose to ignore invalid flag field values must provide a “debug + mode” that does check for invalid flag field values and returns + H_Parameter when any are found. + + Architecture Note: The method for invocation of a + platform’s “debug mode” is beyond the scope of this + architecture. + + + + + + Page Frame Table Access flags field + definition + + + + + + + + + + + + + + Bit + + + + + Function + + + + + Bit + + + + + Function + + + + + Bit + + + + + Function + + + + + Bit + + + + + Function + + + + + + + + 0-15 + + + NUMA CEC Cookie + + + 16-23 + + + Subfunction Codes + + + 32 + + + AVPN + + + 48 + + + Zero Page + + + + + 33 + + + andcond + + + 49 + + + Copy Page + + + + + 34-39 + + + Reserved + + + 50-54 + + + key0-key4 + Bits 50-54 (key0 - key4) shall be treated as reserved + on platforms that either do not contain an + “ibm,processor-storage-keys” property, + or contain an + “ibm,processor-storage-keys” property + with the value of zero in both cells. + + + + + + 55 + + + pp0 + Bit 55 (pp0) shall be treated as reserved on platforms + that do not have the “Support for the “110” + value of the Page Protection (PP) bits” bit set to a + value of 1 in the + “ibm,pa-features” property. + + + + + + 24 + + + Exact + + + 40 + + + I-Cache-Invalidate + + + 56 + + + Compression + + + + + 25 + + + R-XLATE + + + 41 + + + I-Cache-Synchronize + + + 57 + + + Checksum + + + + + 26 + + + READ-4 + + + 42 + + + CC (Coalesce Candidate) + + + 58-60 + + + Reserved + + + + + 27 + + + Reserved + + + 43-47 + + + Reserved + + + + + 28-31 + + + CMO Option Flags + + + + + 61 + + + N + + + + + 62 + + + pp1 + + + + + 63 + + + pp2 + + + + +
+ + + + R1--11. + + For the LPAR option: The caller of Hcall must be in + privileged mode (MSRPR = 0) or the hypervisor immediately returns an + H_Privilege return code. See + for this and other architected + return codes. + + + + + R1--12. + + For the LPAR option: The caller of hcall() must be + prepared for a return code of H_Hardware from all functions. + + + + + R1--13. + + For the LPAR option: + In order for the platform to return H_Hardware, the error must not have resulted in an + undetectable state/data corruption nor will continued operation propagate + an undetectable state/data corruption as a result of the original + error. + Notes: + + + A detectable corruption, when accessed, results in either a + H_Hardware return code, machine check or check stop per platform + policy. + + + + Among other implications of Requirement + are: the effective state of the + partition appears to not change due to the failed hcall() -- (any partial + changes to persistent state/data are backed out); and the recovery of + platform resources that held lost state/data does not hide the state/data + loss to subsequent users of that state/data. + + + + The operating system is not expected to log a serviceable event + due to an H_Hardware return code from an hcall(), and treats the hcall() + as failing due to nonspecific hardware reasons. Any logging of a + serviceable event in response to the underlying cause is handled by + separate platform initiated operations. + + + + + + + + + Hypervisor Call Return Code Table + + + + + + + + + Hypervisor Call Return Code Values + (R3) + + + + + Meaning + + + + + + + + 0x0100000 - 0x0FFFFFFF + + + Function in Progress + + + + + 9905 + + + H_LongBusyOrder100sec - Similar to LongBusyOrder1msec, + but the hint is 100 second wait this time. + + + + + 9904 + + + H_LongBusyOrder10sec - Similar to LongBusyOrder1msec, but + the hint is 10 second wait this time. + + + + + 9903 + + + H_LongBusyOrder1Sec - Similar to LongBusyOrder1msec, but + the hint is 1 second wait this time. + + + + + 9902 + + + H_LongBusyOrder100mSec - Similar to LongBusyOrder1msec, + but the hint is 100mSec wait this time. + + + + + 9901 + + + H_LongBusyOrder10mSec - Similar to LongBusyOrder1msec, + but the hint is 10mSec wait this time. + + + + + 9900 + + + H_LongBusyOrder1msec - This return code is identical to + H_Busy, but with the added bonus of a hint to the partition OS. + If the partition OS can delay for 1 millisecond, the hcall will + likely succeed on a new hcall with no further busy return + codes. If the partition OS cannot handle a delay, they are + certainly free to immediately turn around and try again. + + + + + 18 + + + H_CONTINUE + + + + + 17 + + + H_PENDING + + + + + 16 + + + H_PARTIAL_STORE + + + + + 15 + + + H_PAGE_REGISTERED + + + + + 14 + + + H_IN_PROGRESS + + + + + 13 + + + Sensor value >= Critical high + + + + + 12 + + + Sensor value >= Warning high + + + + + 11 + + + Sensor value normal + + + + + 10 + + + Sensor value <= Warning low + + + + + 9 + + + Sensor value <= Critical low + + + + + 5 + + + H_PARTIAL (The request completed only partially + successful. Parameters were valid but some specific hcall + function condition prevented fully completing the architected + function, see the specific hcall definition for possible + reasons.) + + + + + 4 + + + H_Constrained (The request called for resources in excess + of the maximum allowed. The resultant allocation was + constrained to maximum allowed) + + + + + 3 + + + H_NOT_AVAILABLE + + + + + 2 + + + H_Closed (virtual I/O connection is closed) + + + + + 1 + + + H_Busy + Hardware Busy -- Retry Later + + + + + 0 + + + H_Success + + + + + -1 + + + H_Hardware (Error) + + + + + -2 + + + H_Function (Not Supported) + + + + + -3 + + + H_Privilege (Caller not in privileged mode). + + + + + -4 + + + H_Parameter (Outside Valid Range for Partition or + conflicting) + + + + + -5 + + + bad_mode (Illegal MSR value) + + + + + -6 + + + H_PTEG_FULL (The requested pteg was full) + + + + + -7 + + + H_Not_Found (The requested entity was not found) + + + + + -8 + + + H_RESERVED_DABR (The requested address is reserved by the + hypervisor on this processor) + + + + + -9 + + + H_NOMEM + + + + + -10 + + + H_AUTHORITY (The caller did not have authority to perform + the function) + + + + + -11 + + + H_Permission (The mapping specified by the request does + not allow for the requested transfer) + + + + + -12 + + + H_Dropped (One or more packets could not be delivered to + their requested destinations) + + + + + -13 + + + H_S_Parm (The source parameter is illegal) + + + + + -14 + + + H_D_Parm (The destination parameter is illegal) + + + + + -15 + + + H_R_Parm (The remote TCE mapping is illegal) + + + + + -16 + + + H_Resource (One or more required resources are in + use) + + + + + -17 + + + H_ADAPTER_PARM (invalid adapter) + + + + + -18 + + + H_RH_PARM (resource not valid or logical partition + conflicting) + + + + + -19 + + + H_RCQ_PARM (RCQ not valid or logical partition + conflicting) + + + + + -20 + + + H_SCQ_PARM (SCQ not valid or logical partition + conflicting) + + + + + -21 + + + H_EQ_PARM (EQ not valid or logical partition + conflicting) + + + + + -22 + + + H_RT_PARM (invalid resource type) + + + + + -23 + + + H_ST_PARM (invalid service type) + + + + + -24 + + + H_SIGT_PARM (invalid signalling type) + + + + + -25 + + + H_TOKEN_PARM (invalid token) + + + + + -27 + + + H_MLENGTH_PARM (invalid memory length) + + + + + -28 + + + H_MEM_PARM (invalid memory I/O virtual address) + + + + + -29 + + + H_MEM_ACCESS_PARM (invalid memory access control) + + + + + -30 + + + H_ATTR_PARM (invalid attribute value) + + + + + -31 + + + H_PORT_PARM (invalid port number) + + + + + -32 + + + H_MCG_PARM (invalid multicast group) + + + + + -33 + + + H_VL_PARM (invalid virtual lane) + + + + + -34 + + + H_TSIZE_PARM (invalid trace size) + + + + + -35 + + + H_TRACE_PARM (invalid trace buffer) + + + + + -36 + + + H_TRACE_PARM (invalid trace buffer) + + + + + -37 + + + H_MASK_PARM (invalid mask value) + + + + + -38 + + + H_MCG_FULL (multicast attachments exceeded) + + + + + -39 + + + H_ALIAS_EXIST (alias QP already defined) + + + + + -40 + + + H_P_COUNTER (invalid counter specification) + + + + + -41 + + + H_TABLE_FULL (resource page table full) + + + + + -42 + + + H_ALT_TABLE (alternate table already exists / alternate + page table not available) + + + + + -43 + + + H_MR_CONDITION (invalid memory region condition) + + + + + -44 + + + H_NOT_ENOUGH_RESOURCES (insufficient resources) + + + + + -45 + + + H_R_STATE (invalid resource state condition or sequencing + error) + + + + + -46 + + + H_RESCINDED + + + + + -54 + + + H_Aborted + + + + + -55 + + + H_P2 + + + + + -56 + + + H_P3 + + + + + -57 + + + H_P4 + + + + + -58 + + + H_P5 + + + + + -59 + + + H_P6 + + + + + -60 + + + H_P7 + + + + + -61 + + + H_P8 + + + + + -62 + + + H_P9 + + + + + -63 + + + H_NOOP + + + + + -64 + + + H_TOO_BIG + + + + + -65 + + + Reserved + + + + + -66 + + + Reserved + + + + + -67 + + + H_UNSUPPORTED (Parameter value outside of the range + supported by this implementation) + + + + + -68 + + + H_OVERLAP (unsupported overlap among passed buffer + areas) + + + + + -69 + + + H_INTERRUPT (Interrupt specification is invalid) + + + + + -70 + + + H_BAD_DATA (uncorrectable data error) + + + + + -71 + + + H_NOT_ACTIVE (Not associated with an active + operation) + + + + + -72 + + + H_SG_LIST (A scatter/gather list element is + invalid) + + + + + -73 + + + H_OP_MODE (There is a conflict between + the subcommand and the requested operation + notification) + + + + + -74 + + + H_COP_HW (co-processor hardware error) + + + + + -75 + + + H_STATE (invalid state) + + + + + -76 + + + H_RESERVED (a reserved value was specified) + + + + + -77 : -255 + + + Reserved + + + + + -256 -- -511 + + + H_UNSUPPORTED_FLAG (An unsupported binary flag bit was + specified. The returned value is -256 - the bit position of the + unsupported flag bit [high order flag bit is 0 etc.]) + + + + +
+
+ +
+ Hypervisor Call Functions + + +
+ Page Frame Table Access + All hypervisor Page Frame Table (PFT) access routines are called + using 64 bit linkage conventions and apply to all page sizes that the + platform supports as specified by the + “ibm,processor-page-sizes” property (See + for more details). The hypervisor PFT + access functions carefully update a given Page Table Entry (PTE) with at + least 64 bit store operations since an invalid update sequence could + result in machine checks. To guard against multiple conflicting + allocations of a PTE that could result in a check stop condition, the + hypervisor PTE allocation routine (H_ENTER) reserves the first two (high + order) software PTE bits for use as PTE locks while the low order two + software PTE bits are reserved for OS use (not used by firmware). If a + firmware PTE bit is on, the OS is to assume that the PTE is in use, just + as if the V bit were on. The hypervisor PFT access routines often execute + the tlbie instruction, on certain platforms, this instruction may only be + executed by one processor in a partition at a time, the hypervisor uses + locks to assure this. The tlbie instruction flushes a specific translate + lookaside buffer (TLB) entry from all processors participating in the + protocol. All the processors participating in the tlbie protocol are + defined as a translation domain. All processors of a given partition that + are in a given translation domain share the same hardware PFT. Book III + of the PA specifies the codes sequences needed to safely access the PFT, + in its chapter titled “Storage Control Instructions and Table + Updates”. These code sequences are part of this specification by + reference. The hypervisor PFT access routines are in the critical + performance path of the machine, therefore, extraordinary care must be + given to their performance, including machine dependent coding, minimal + run time checking, and code path length optimization. For performance + reasons, all parameter linkage is through registers, and no indirect + parameter linkage is allowed. This requires special glue code on the part + of the caller to pick up the return parameters. The hypervisor PFT access + routines modify the calling processor’s partition PFT on the + calling node. On NUMA systems, if an LPAR partition spans multiple + Central Electronics Complexes (CECs), the partition’s processors + may be in separate translation domains. Each platform translation domain + has a separate PFT. Therefore, the partition’s OS must modify each + PFT individually. This is done either by making hcall() accesses + specifying the NUMA CEC Cookie (which identifies the translation domain) + in the high order 16 bits of the flags parameter (H_ENTER and H_READ + only) or by issuing the hcall() from a processor within the translation + domain as identified by the processor’s NUMA CEC Cookie field of + the + “ibm,pft-size” property. + The PFT is preallocated based upon the value of the + partition’s PFT_size configuration variable. This configuration + variable is initialized to 4 PTEs per node local page frame and 2 PTEs + per remote node page frame. The size of the PFT per node is communicated + to the partition’s OS image via the + “ibm,pft-size” property of the + node. + The value of the configuration variable + PFT_size consists of two comma separated integers, + the first is the number of hardware PFT entries to allocate per CEC local + page, and the second is the number of hardware PFT entries to allocate + per remote CEC page (if NUMA configured). These allocations are made at + partition boot time based upon the initial partition memory allocation, + based upon specific situations (such as low page table usage or future + need for dynamic memory addition) the OS may wish to override the + platform default values. + + + + R1--1. + + For the LPAR option: The platform must allocate the + partition’s page frame table. The size of this table is determined + by the PFT_size configuration variable in the OS image’s + “common” NVRAM partition. + + + + + R1--2. + + For the LPAR option: The platform must provide the + “ibm,pft-size” property in the processor + nodes of the device tree (children of type + cpu of the + /cpus node). + Register Linkage (For hcall() tokens 0x04 - 0x18) + + + + + + On Call: + + R3 function call token + R4 flags (see ) + R5 Page Table Entry Index (PTEX) + R6 Page Table Entry High word (PTEH) (on H_ENTER only) + R7 Page Table Entry Low word (PTEL) (on H_ENTER only) + + + On Return: + + R3 Status Word + R4 chosen PTEX (from H_ENTER) / High Order Half of old PTE + R5 Low Order Half of old PTE + R6 + + + + + Semantics checks for all hypervisor PTE access routines: + + + + Hypervisor checks that the caller was in privileged mode or + H_Privilege return code. + + + + On NUMA platforms for the H_ENTER and H_READ calls only, the + hypervisor checks that the NUMA CEC Cookie is within the range of values + assigned to the partition else return H_Parameter. + + + + Hypervisor checks that the PTEX is zero or greater and less than + the partition maximum, else H_Parameter return code. + + + + Hypervisor checks the logical address contained in any PTE to be + entered into the PFT to insure that it is valid and then translates the + logical address into the assigned physical address. + + + + When hypervisor returns the contents of a PTE, the contents of + the RPN are usually architecturally undefined. It is expected that + hypervisor implementations leave the contents of this field as it was + read from the PTE since it cannot be used by the OS to directly access + real memory. The exception to this rule is when the R-XLATE flag is + specified to the H_READ hcall(), then the RPN in the PTE is reverse + translated into the LPN prior to return. + + + + Logical addressing: + LPAR adds another level of virtual address translation managed by + the hypervisor. The OS is never allowed to use the physical address of + its memory this includes System Memory, MMIO space, NVRAM etc. The OS + sees System Memory as N regions of contiguous logical memory. Each + logical region is mapped by the hypervisor into a corresponding block of + contiguous physical memory on a specific node. All regions on a specific + system are the same size though different systems with different amount + of memory may have different region sizes since they are the quantum of + memory allocation to partitions. That is, partitions are granted memory + in region size chunks and if a partition’s OS gives up memory, it + is in units of a full region. On NUMA platforms, groups of regions may be + associated with groups of processors forming logical CECs for allocation + and migration purposes. + Logical addresses are divided into two fields, the logical region + identifier and the region offset. The region offset is the low order bits + needed to represent the region size. The logical region identifier are + the remaining high order bits. + + + + Logical addresses start at zero. When control is initially passed + to the OS from the platform, the first region is the single RMA. The + first region has logical region identifier of zero. This first region is + specified by the first address - length pair of the + “reg” property of the + /memory node of the OF device tree. Subsequent + regions each have their own address - length pair. At initial program + load time, the logical region identifiers are sequential starting at zero + but over time, with dynamic memory reconfiguration, holes may appear in + the partition’s address space. + + + + Logical to physical translation: This translation is based upon a + simple indexed table per partition of the physical addresses associated + with the start of each region (in logical region identifier order). At + least two special values are recognized: + + + + The invalid value for those regions that do not have a physical + mapping (so that there can be holes in the logical address map for + various reasons such as memory expansion). + + + + The I/O region value, that calls for further checking against + partition I/O address range allocations. + + + + + + + The logical region identifier is checked for being less than the + maximum size, and then used to index the logical to physical translation + table. + + + + If the physical region identifier is valid (certain values are + reserved say 0 and all F’s) then it replaces the logical region + identifier in the PTE and the PTE access function continues. + + + + If the physical region identifier is the I/O region, then proceed + to the I/O translation algorithm (implementation dependent based upon + platform characteristics). + + + + If the physical region identifier is invalid, return + H_Parameter + + + + + + R1--3. + + For the LPAR option: The OS must make no assumptions + about the logical to physical mapping other than the low order + bits. + + + + + R1--4. + + For the LPAR option: Each logical region must have + its own address - length pair in the + “reg” property of the OF + /memory node. + + + + + R1--5. + + For the LPAR option: When control is initially passed + to the OS from the platform, the first logical region (having logical + region identifier 0) must be the region accessed when the OS operates + with translate off. + + + + + R1--6. + + For the LPAR option: When control is initially passed + to the OS from the platform, the size of the logical region must be equal + to a real mode length size supported by the platform. + + + + + R1--7. + + For the LPAR option: + Each logical region must start and end on a boundary of the largest page size that the + logical region supports (see + “ibm,dynamic-memory” and + “ibm,lmb-page-sizes” in + as well as + for more details). + + + + + R1--8. + + For the LPAR option: The pages that contain the + platform’s per processor interrupt management areas or any other + device marked + “used-by-rtas” must not be mapped into + the partition virtual address space. + + + + + R1--9. + + For the LPAR option: + Each logical region must support all page sizes presented in the + “ibm,processor-page-sizes” property in + that are less than or equal to the + size of the logical region as specified by either the OF standard + “reg” property of the logical + region’s OF + /memory node, or the + “ibm,lmb-size” property of the logical + region’s + /ibm,dynamic-reconfiguration-memory node in + . + + Implementation Note: 32 bit versions of AIX only support 36 bit + logical address memory spaces. Providing such a partition with a larger + logical memory address space may cause OS failures. + + Implementation Note: Requirement + may be met by ensuring that all + logical regions start and end on a boundary of the largest page size + supported by the platform. + + + + +
+ H_REMOVE + This hcall is for invalidating an entry in the page table. The PTEX + identifies a specific page table entry. If the PFO option is implemented + an optional flag causes the hypervisor to compress the page contents to + one or more data blocks after invalidating the page table entry given + that a compression coprocessor is available and the page is small enough + to be synchronously compressed. If the compression coprocessor is busy, + or the page is too large, the compression can be subsequently performed + using the H_COP_OP hcall() see + . If the page contents are + compressed, then a checksum may be appended by setting the checksum flag + - if the compression flag is not set the checksum flag is + ignored. + + + Syntax: + + + + + + + Parameters: + + + flags: AVPN, andcond, and for the CMO option: CMO Option flags as + defined in + and for the PFO option the + compression and checksum flags. + + + + PTEX (index of the PTE in the page table to be used) + + + + AVPN: Optional “Abbreviated Virtual Page Number” -- + used as a check for the correct PTE + + + + When the AVPN flag is set, the contents of the AVPN parameter are + compared to the first double word of the PTE (after bits 57-63 of the PTE + have been masked). Note, the low order 7 bits are undefined and should be + zero otherwise the likely result is a return code of H_Not_Found. + + + + When the andcond flag is set, the contents of the AVPN parameter + are bit anded with the first double word of the PTE. If the result is + non-zero the return code is H_Not_Found. + + + + + + out: For the PFO option, the output data block logical real + address when the compression flag bit is on. + + + + outlen: For the PFO option, the length of the compression data + block or compression data block descriptor list when the compression flag + bit is on. + + + + + + Semantics: + + + Check that the PTEX accesses within the PFT else return + H_Parameter + + + + If the AVPN flag is set, and the AVPN parameter bits 0-56 do not + match that of the specified PTE then return H_Not_Found. + + + + If the andcond flag is set, the AVPN parameter is bit anded with + the first double word of the specified PTE, if the result is non-zero, + then return H_Not_Found. + + + + The hypervisor Synchronizes the PTE specified by the PTEX and + returns its value + + + + Use the architected “Deleting a Page Table Entry” + sequence such that the first double word of the resultant PFT entry is + all 0s. + + + + Use the proper tlbie instruction for the page size within a + critical section protected by the proper lock (per large page bit in the + specified PTE). + + + + The synchronized value of the old PTE value ends up in R4 and R5 + for return to the caller. + + + + For the CMO option: set the page usage state per the CMO Option + flags field of the flags parameter as defined in + . + + + + + + For the PFO option: If the Compression flag is on: + + + + Check that the calling partition is authorized to use the + compression co-processor else return H_Function. + + + + If the page is not “main store memory” then return + H_UNSUPPORTED_FLAG TBD (value - 312) + + + + Check that the page size is <= the compression value in + “ibm,max-sync-cop” else return + H_Constrained. + + + + Build CRB for compression of the page size indicated in the + PTE + + + + If the checksum flag is on command that a checksum be + built + + + + Verify that the “out” parameter represents a valid + logical real address within the caller’s partition else return + H_P3 + + + + If the “outlen” parameter is non-negative verify that + the logical real address of (out + outlen) is a valid logical real + address within the same 4K page as the “out” parameter else + return H_P4. + + + + If the “outlen” parameter is negative: + + + + Verify that the absolute value of outlen meet all of the follow + else return H_P4: + + + + Is <= the value of + “ibm,max-sg-len” + + + + Is an even multiple of 16 + + + + That out + the absolute value of outlen represents a valid + logical real address within the same 4K page as the out parameter. + + + + + + Verify that each 16 byte scatter gather list entry meets all of + the following else return H_SG_LIST: + + + + Verify that the first 8 bytes represents a valid logical real + address within the caller’s partition. + + + + Verify that the logical real address represented by the sum of + the first 8 bytes and the second 8 bytes is a valid logical real address + within the same 4K page as the first 8 bytes. + + + + + + + + For the Shared Logical Resource Option if any of the memory + represented by the out/outlen parameters have been rescinded then return + H_RESCINDED. + + + + Fill in the destination DDE list from the converted the + out/outlen parameters. + + + + Issue icswx instruction to execute CRB + + + + Check coprocessor busy - retry / return H_PARTIAL if + execution time expired / return H_COP_HW if compressor is broken + + + + Wait for coprocessor to complete + + + + If compressor hardware error return H_COP_HW + + + + Check that the compressor had enough room to house the compressed + image else return H_TOO_BIG + + + + Save compression block size in R6 + + + + + + Return H_Success + + + + +
+ +
+ H_ENTER + This hcall adds an entry into the page frame table. PTEH and PTEL + contain the new entry. PTEX identifies either the page table entry group + or the specific PTE where the entry is to be added, depending upon the + setting of the Exact flag. If the Exact flag is off, the hypervisor + selects the first free (invalid) PTE in the page table entry group. For + pages with sizes less than or equal to 64 K, Flags further provide the + option to zero the page, and provide two levels of programmed I-Cache + coherence management before activating the page table mapping. This hcall + returns the PTE index of the entered mapping. If the PFO option is + implemented an optional compression flag causes the hypervisor to + initialize the page from one or more compressed data blocks and + optionally (checksum flag) check the end to end block data integrity + prior to adding the entry to the page table. If the compression flag is + not set the checksum flag is ignored. + + + + + Parameters: + + + + Flags + + + + CEC Cookie + + + + Zero Page: Zero the System Memory page in real mode before + placing its mapping into the PTE. This flag is ignored for memory mapped + I/O space pages; as an attempt to zero missing memory might result in a + machine check or worse. This function should use a processor dependent + algorithm optimized for maximum performance on the specific hardware. + This usually is a sequence of dcbz instructions. Setting this flag for a + page with a size larger than 64 K will result in return code of + H_TOO_BIG. + + + + I-Cache-Invalidate: Issue an icbi etc. instruction sequence to + manage the I-Cache coherency of the cachable page. This flag is ignored + for memory mapped I/O pages. For use when the D-Cache is known to be + clean, before placing its mapping into the PTE. Setting this flag for a + page with a size larger than 64 K will result in return code of + H_TOO_BIG. + + + + I-Cache-Synchronize: Issue dcbst and icbi, etc., instruction + sequence to manage the I-Cache coherency of the cachable page. This flag + is ignored for memory mapped I/O pages. For use when the D-Cache may + contain modified data, before placing its mapping into the PTE. Setting + this flag for a page with a size larger than 64 K will result in return + code of H_TOO_BIG. + + + + Exact: Place the entry in the exact PTE specified by PTEX if it + is empty else return H_PTEG_FULL. + + + + For the CMO option: CMO Option flags as defined in + . + + + + For the PFO option: the compression flag initializes the page + content from a compression buffer and the checksum flag checks for end to + end compression buffer data integrity. + + + + + + PTEX (index of the first PTE in the page table entry group to be + used for the PTE insertion) + + + + PTEH -- the high order 8 bytes of the page table entry. + + + + PTEL -- the low order 8 bytes of the page table entry. + + + + + + + Semantics: + + + + The hypervisor checks that the logical page number is within the + bounds of partition allocated memory resources, else returns + H_Parameter. + + + + If the Shared Logical Resource option is implemented and the + logical page number represents a page that has been rescinded by the + owner, return H_RESCINDED. + + + + + + The hypervisor checks that the address boundary matches the + setting of the input PTE’s large page bits; else return + H_Parameter. + + + + The hypervisor checks that the page size described by the setting + of the input PTE’s page size bits is less than or equal to the + largest page size supported by the logical region that is being mapped; + else return H_Parameter. + + + + The hypervisor checks that the WIMG bits within the PTE are + appropriate for the physical page number else H_Parameter return. (For + System Memory pages WIMG=0010, or, 1110 if the SAO option is enabled, and + for IO pages WIMG=01**.) + + + + For pages with sizes greater than 64 K, the hypervisor checks + that the Zero Page, I-Cache-Invalidate, and I-Cache_Synchronize bits of + the Flags parameter are not set; else return H_TOO_BIG. + + + + Force off RS mode reserved PTEL bits (1 + In addition, bits 52 and 53 are forced off on platforms that + either do not contain an + “ibm,processor-storage-keys” property, + or contain an + “ibm,processor-storage-keys” property + with the value of zero in both cells. Bit 0 is forced off on platforms + that do not have the “Support for the “110” value of + the Page Protection (PP) bits” bit set to a value of 1 in the + “ibm,pa-features” property. + ) as well as hypervisor reserved software bits (57 and 58) in + PTEH. + + + + If the Exact flag is off, set the low order 3 bits of the PTEX to + zero (insures that the algorithm stays inside partition’s PFT and + is faster than a check and error code response). + + + + If the Zero Page flag is set, use optimized routine to clear page + (usually series of dcbz instructions). + + + + For the PFO option: if the compression flag is on then + + + + Check that the calling partition is authorized to use the + compression co-processor else return H_Function. + + + + If the page is not “main store memory” then return + H_UNSUPPORTED_FLAG. + + + + Build CRB for decompression + + + + If the checksum flag is on command that a checksum be + verified. + + + + + Validate the inlen/in parameters and build the source DDE + + + + Verify that the “in” parameter represents a valid + logical real address within the caller’s partition else return + H_P4 + + + + If the “inlen” parameter is non-negative verify that + the logical real address of (in + inlen) is a valid logical real address + within the same 4K page as the “in” parameter else return + H_P5. + + + + If the “inlen” parameter is negative: Verify that the + absolute value of inlen meet all of the follow else return H_P5: + + + + Is <= the value of + “ibm,max-sg-len” + + + + Is an even multiple of 16 + + + + That in + the absolute value of inlen represents a valid logical + real address within the same 4K page as the in parameter. + + + + + + Verify that each 16 byte scatter gather list entry meets all of + the following else return H_SG_LIST: + + + + Verify that the first 8 bytes represents a valid logical real + address within the caller’s partition. + + + + Verify that the logical real address represented by the sum of + the first 8 bytes and the second 8 bytes is a valid logical real address + within the same 4K page as the first 8 bytes. + + + + + + Verify that the sum of all the scatter gather length fields + (second 8 bytes of each 16 byte entry) is <= the decompression value + in + “ibm,max-sync-cop” else return + H_TOO_BIG. + + + + + + For the Shared Logical Resource Option if any of the memory + represented by the in/inlen parameters have been rescinded then return + H_RESCINDED. + + + + Fill in the source DDE list from the converted the in/inlen + parameters. + + + + Build the destination DDE referencing the start of the PTE page + with the length of the PTE page size. + + + + Issue icswx instruction to execute CRB + + + + Check coprocessor busy - retry / return H_Busy if execution + time exhausted / return H_Hardware if compressor is broken + + + + Wait for coprocessor to complete + + + + If compressor ran out of destination space return + H_TOO_BIG + + + + Check that the decompression filled the full page else return + H_Aborted + + + + If the checksum flag is on check that the data is valid else + return H_BAD_DATA + + + + If hardware error return H_Hardware + + + + + + If the I-Cache-Invalidate flag is set, issue icbi instructions + for all of the page’s cache lines + + + + If the Cache-Synchronize flag is set, issue dcbst and icbi + instructions for all of the page’s cache lines. Implementations may + need to issue a sync instruction to complete the coherency management of + the I-Cache. + + + + The hypervisor selects a PTE within the page table entry group + using the following. + + + + + + + Algorithm: + + + + if Exact flag is on then set t to 0 else set t to 7 + + + + for i=0;i<= t; i++ + + + + Combine page table base, PTEX and offset base on (i) into + R3 + + + + R8 <- ldarx PTEH(R3) /* prepare to take a lock on the PTE + */ + + + + if PTE is valid (R8 (bit 63) is set) then continue + + + + if PTE is locked (R8 (bit 57) is set) then continue + + + + set R8 (bit 57) /* prepare to lock PTE */ + + + + PTEH(R3) <- stdcx R8 /* attempt to take lock */ + + + + if stdcx failed continue + + + + goto insert + + + + + + return H_PTEG_FULL + + + + insert: use code sequence from PA Book III + + + + construct return PTEX (R4 <- (R3 - PFTbase) shifted down 4 + places) + + + + For the CMO option: set the page usage state per the CMO Option + flags field of the flags parameter as defined in + . + + + + return H_Success + + + + +
+ +
+ H_READ + This hcall returns the contents of a specific PTE in registers R4 + and R5. + + + + + Parameters: + + + + + flags: + + + + CEC Cookie: Cross CEC PFT access + + + + READ_4: Return 4 PTEs + + + + R-XLATE: Include a valid logical page number in the PTE if the + valid bit is set, else the contents of the logical page number field is + undefined. + + + + For the CMO option: CMO Option flags as defined in + . + + + + + + PTEX (index of the PTE in the page table to be used -- if the + READ_4 flag is set the low order two bits of the PTEX are forced to zero + by the hypervisor to insure that they are in the range of the PTEG and it + is faster than checking.) + + + + + + + Semantics: + + + + Checks that the PTEX is within the defined range of the + partition’s PFT else return H_Parmaeter + + + + If the READ_4 bit is clear Then load the specified PTE into R4 + and R5 + + + + If R-XLATE flag is set, then reverse translate the RPN field into + the logical page number. + + + + + + Else + + + + clear the two low order bits of the PTEX (faster than checking + them) + + + + load the 4 PTEs starting at PTEX into R4 through R11. + + + + If R-XLATE flag is set, then reverse translate the RPN fields + into the logical page number. + + + + + + + + For the CMO option: set the page usage state per the CMO Option + flags field of the flags parameter as defined in + . + + + + Set H_Success in R3 and return + + + + +
+ +
+ H_CLEAR_MOD + + This hcall clears the modified bit in the specific PTE. The second + double word of the old PTE is returned in R4. + + + + + Parameters: + + + + flags: For the CMO option: CMO Option flags as defined in + . + + + + PTEX (index of the PTE in the page table to be used) + + + + + + Semantics: + + + + Check that the PTEX accesses within the PFT, else returns + H_Parameter + + + + Check that the “V” bit is one, else return + H_Not_Found. + + + + Fetch the low order double word of the PTE into R4. If the + “C” bit is zero, then return H_Success. + + + + The hypervisor synchronizes the PTE specified by the PTEX, clears + the mod bit, and returns its old value: + + + + Use the architected “Modifying a Page Table Entry General + Case” sequence from PA Book III. + + + + Only PTE bits to be modified are: + + + + In double word 0 SW bit 57 and the V bit (63) + + + + In double word 1, C bit (56). + + + + + + Use the proper tlbie instruction for the page size (per large + page flag within PTE) within a critical section protected by the proper + lock. + + + + The second double word of the old PTE value ends up in R4. + + + + At the point where the new values are to be activated, use the + old values with the “C” bit cleared. + + + + For the CMO option: set the page usage state per the CMO Option + flags field of the flags parameter as defined in + . + + + + Return H_Success + + + + + + +
+ +
+ H_CLEAR_REF + This hcall clears the reference bit in the specific PTE. The second + double word of the old PTE is returned in R4. + + + + + Parameters: + + + + flags: For the CMO option: CMO Option flags as defined in + . + + + + PTEX (index of the PTE in the page table to be used) + + + + + + Semantics: + + + + Check that the PTEX accesses within the PFT, else return + H_Parameter. + + + + Check that the “V” bit is one, else return + H_Not_Found. + + + + Only PTE bits to be modified are: + + + + In double word 1 the R bit (55) + + + + + + Use the architected “Resetting the Reference Bit” + sequence from PA Book III with the original second double word of the PTE + ending up in R4. + + + + For the CMO option: set the page usage state per the CMO Option + flags field of the flags parameter as defined in + . + + + + Return H_Success + + + + +
+ +
+ H_PROTECT + This hcall sets the page protect bits in the specific PTE. + + + + + Parameters: + + + + flags: AVPN, pp0 + The pp0 portion of the flags parameter is ignored on platforms + that do not have the “Support for the “110” value of + the Page Protection (PP) bits” bit set to a value of 1 in the + “ibm,pa-features” property. + , pp1, pp2, key0-key4 + The key0-key4 portion of the flags parameter is ignored on + platforms that either do not contain an + “ibm,processor-storage-keys” property, + or contain an + “ibm,processor-storage-keys” property + with the value of zero in both cells. + , n, and for the CMO option: CMO Option flags as defined in + . + + + + PTEX (index of the PTE in the page table to be used) + + + + AVPN: Optional “Abbreviated Virtual Page Number” -- + used as a check for the correct PTE when the AVPN flag is set. + + + + + + + Semantics: + + + + Check that the PTEX accesses within the PFT, else return + H_Parameter + + + + Check that the “V” bit is one, else return + H_Not_Found. + + + + If the AVPN flag is set, and the AVPN parameter bits 0-56 do not + match that of the specified PTE, then return H_Not_Found. + + + + The hypervisor synchronizes the PTE specified by the PTEX, sets + the pp0 + The pp0 bit is not modified on platforms that do not have the + “Support for the “110” value of the Page Protection + (PP) bits” bit set to a value of 1 in the + “ibm,pa-features” property. + , pp1, pp2, key0-key4 + The key0 - key4 bits are not modified on platforms that either + do not contain an “ibm,processor-storage-keys” + property, or contain an + “ibm,processor-storage-keys” property + with the value of zero in both cells. + , and n bits per the flags parameter. + + + + Only PTE bits to be modified are: + + + + In double word 0 SW bit 57 and the V bit (63) + + + + In double word 1 pp0, pp1, pp2, + key0-key4, and n + + + + + + Use the architected “Modifying a Page Table Entry General + Case” sequence. + + + + Use the proper tlbie instruction for the page size (per value in + PTE) within a critical section protected by the proper lock. + + + + At the point where the new values are to be activated use the old + values with the “R” bit cleared and the + pp0, + pp1, pp2, key0-key4, + and n bits set as specified in + the flags parameter. + + + + For the CMO option: set the page usage state per the CMO Option + flags field of the flags parameter as defined in + . + + + + Return H_Success + + + + + + +
+ +
+ H_BULK_REMOVE + This hcall is for invalidating up to four entries in the page + table. The PTEX in the translation specifier high parameters identifies + the specific page table entries. + Prototype: + + + + Translation specifiers: + Each is 16 bytes long made up of two 8 byte double words; a + translation specifier high and a translation specifier low. + + + + Translation Specifier High double word: + + + + First byte (0) is a control/status byte: + + + + High order two bits (0 and 1) are type code: + + + + 00 Unused -- if found stop processing and return + H_PARAMETER + + + + 01 Request -- Processes As per H_REMOVE as modified by low order + two control bits. + + + + 10 Response -- written by hypervisor as a return status from + processing individual “request” translation specifier + + + + 11 End of String -- if found stop processing and return + H_Success. + + + + + + Next two bits (2 and 3) are response code (in response to + processing an individual “request” translation specifier + (type code modified to 10)): + + + + 00 Success -- the specified translation was removed as per + H_REMOVE with the PTE's RC bits in the next two status bits. + + + + 01 Not found -- the specified translation was not found as per + H_REMOVE. + + + + 10 H_PARM -- one or more of the parameters of the specified + translation were invalid per H_REMOVE -- processing of the bulk entries + stops at this point and the hypervisor returns H_PARAMETER. + + + + 11 H_HW -- The hardware experienced an uncorrected error + processing this translation specifier -- processing of the bulk entries + stops at this point and the hypervisor returns H_HARDWARE. + + + + + + Next two bits (4 and 5) are the Reference/Change bits from the + removed PTE (These bits are only valid if bits 0-3 are 1000): + + + + Low order two bits (6 and 7) are request modification + flags: + + + + 00 absolute -- remove the specified PTEX entry + unconditionally + + + + 01 andcond -- remove the specified PTEX entry as with the andcond + flag of H_REMOVE + + + + 10 AVPN -- remove the specified PTEX entry as with the AVPN flag + of H_REMOVE + + + + 11 not used -- if found stop processing and return + H_PARAMETER. + + + + + + + + Bytes 1 through 7 are the PTEX (PFT byte offset divided by + 16) + + + + + + Translation Specifier Low double word: + + + + Bytes 0 through 7 are the AVPN as per H_REMOVE + + + + + +
+ + Semantics: + + + + For each translation specifier, while the translation specifier + is not “end of string”: + + + + Check that the PTEX accesses within the PFT else set H_PARM + response status in the specific translation specifier high register and + return H_Parameter + + + + If the AVPN flag is set, and the AVPN parameter bits 0-56 do not + match that of the specified PTE then set response status Not found in the + specific translation specifier high register, Continue. + + + + If the andcond flag is set, the AVPN parameter is bit anded with + the first double word of the specified PTE (after bits 57-63 of the PTE + have been masked), if the result is non-zero, then set response status + Not found in the specific translation specifier high register, Continue. + (Note the low order 7 bits of the AVPN parameter should be zero otherwise + the likely result is a response status of Not found). + + + + The hypervisor Synchronizes the PTE specified by the PTEX. + + + + Use the architected “Deleting a Page Table Entry” + sequence. + + + + Use the proper tlbie instruction for the page size within a + critical section protected by the proper lock (per large page bit in the + specified PTE). + + + + The synchronized value of the old PTE RC bits ends up in bits 4 + and 5 of the individual translation specifier high register along with + success response status. + + + + + + return H_Success + + + + +
+ +
+ Translation Control Entry Access + The Translation Control Entry (TCE) access hcall()s take as a + parameters the Logical I/O Bus Number (LIOBN) that is the logical bus + number value derived from the + “ibm,dma-window” property associated with + the particular IOA. For the format of the + “ibm,dma-window” property, reference + . + +
+ H_GET_TCE + This hcall() returns the contents of a specified Translation + Control Entry. + + + Syntax: + + + + + + + Parameters: + + + + LIOBN (Logical I/O Bus Number for TCE table to be + accessed) + + + + IOBA (I/O Bus Address for indexing into the TCE table) + + + + + + Semantics: + + + + If the LIOBN, or IOBA are outside of the range of calling + partition assigned values return H_PARAMETER. + + + + If the Shared Logical Resource option is implemented and the + LIOBN, or IOBA represents a logical resource that has been rescinded by + the owner, return H_RESCINDED. + + + + + + Load R4 with the specified TCE contents. + + + + If specified TCE’s Page Mapping and Control bits (see + ) specify “Page Fault” then + return H_Success + + + + Reverse translate the TCE’s RPN field into its logical page + number + + + + If the logical page number is owned by the calling partition then + replace the RPN field of R4 with the logical page number and return + H_Success. + + + + Logically OR the contents of R4 with 0xFFFFFFFFFFFFF000 placing + the result into R4. + + + + Return H_PARTIAL. + + + + +
+ +
+ H_PUT_TCE + This hcall() enters the mapping of a single 4 K page into the + specified Translation Control Entry. + + + Syntax: + + + + + + + Semantics: + + + + If the LIOBN or IOBA parameters are outside of the range of + calling partition assigned values return H_PARAMETER. + + + + If the Shared Logical Resource option is implemented and the + LIOBN, or IOBA represents a logical resource that has been rescinded by + the owner, return H_RESCINDED. + + + + + + If the Page Mapping and Control field of the TCE is not + “Page Fault” (see + ) + + + + Then if the logical address within the TCE parameter is outside + of the range of calling partition assigned values + + + + Then return H_PARAMETER. + + + + Else translate the logical address within the TCE parameter into + the corresponding physical real address. + + + + + + + + The hypervisor stores the TCE resultant value in the TCE table + specified by the LIOBN and IOBA parameters; returning H_Success. (In the + “Page Fault” case the RPN remains untranslated.) + + Software Note: The PA requires the OS to issue a sync instruction + to proceed the signalling of an IOA to start an IO operation involving + DMA to guarantee the global visibility of both DMA and TCE data. This + hcall() does not include a sync instruction to guarantee global + visibility of TCE data and in no way diminishes the requirement for the + OS to issue it. + + + + +
+ +
+ H_STUFF_TCE + This hcall() duplicates the mapping of a single 4 K page through + out a contiguous range of Translation Control Entries. Thus, in + initializing and/or invalidating many entries. To retain interrupt + responsiveness this hcall() should be called with a count parameter of no + more than 512, LoPAR architecture provides enforcement for this + restriction to aid in client code debug. + + + Syntax: + + + + + + + Semantics: + + + + If the LIOBN, or IOBA, are outside of the range of calling + partition assigned values return H_PARAMETER. + + + + If the Shared Logical Resource option is implemented and the + LIOBN, or IOBA represents a logical resource that has been rescinded by + the owner, return H_RESCINDED. + + + + + + If the count parameter is greater than 512 then return + H_P4 + + + + If the count parameter added to the TCE index specified by IOBA + is outside of the range of the calling partition assigned values return + H_PARAMETER. + + + + If the Page Mapping and Control field of the TCE is not + “Page Fault” (see + ) + + + + Then if the logical address within the TCE parameter is outside + of the range of calling partition assigned values + + + + Then return H_PARAMETER. + + + + If the Shared Logical Resource option is implemented and the + logical address’s page number represents a page that has been + rescinded by the owner, return H_RESCINDED. + + + + + + Else translate the logical address within the TCE parameter into + the corresponding physical real address. + + + + + + + + The hypervisor stores the TCE resultant value in the TCE table + entries specified by the LIOBN, IOBA and count parameters; returning + H_Success. (In the “Page Fault” case the RPN remains + untranslated.) + + + + Implementation Note: The PA requires the OS to issue a sync + instruction to proceed the signaling of an IOA to start an IO operation + involving DMA to guarantee the global visibility of both DMA and TCE + data. This hcall() does not include a sync instruction to guarantee + global visibility of TCE data and in no way diminishes the requirement + for the OS to issue it. + +
+ +
+ H_PUT_TCE_INDIRECT + This hcall() enters the mapping of up to 512 4 K pages into the + specified Translation Control Entry. The LIOBN parameter if positive is + the cookie (LIOBN) of the specific TCE table to load. For the Multi-TCE + Table (MTT) option, if the LIOBN parameter is negative, CNT = the + absolute value of LIOBN (up to 128), and the first CNT 8 byte entries of + the buffer referenced by the TCE parameter contains the TCE table cookies + (LIOBNs) for the various TCE tables to load (up to a maximum of 128 TCE + tables). + + Note: Users of the MTT option that are subject to + partition migration should be prepared for the loss of support for the + MTT option after partition migration. + + + Syntax: + + + + + + Semantics: + /* Validate the input parameters */ + + + + If the LIOBN parameter is non-negative then do + + + + If the count parameter is > 512 then return + H_Parameter. + + + + If the Shared Logical Resource option is implemented and the + LIOBN parameter represents a TCE table that has been rescinded by the + owner, return H_RESCINDED. + + + + If the LIOBN parameter represents a TCE table that is not valid + for the calling partition, return H_Parameter. + + + + Liobns[0] = the LIOBN parameter. + + + + If the Shared Logical Resource option is implemented and any of + the I/O bus address range represented the IOBA parameter plus count pages + within the TCE table represented by the LIOBN parameter represents + rescinded resource, return H_RESCINDED. + + + + If any of the I/O bus address range represented the IOBA + parameter plus count pages within the TCE table represented by the LIOBN + parameter is not valid for the calling partition then return + H_Parameter. + + + + end + + + + + + Else do + + + + If the MTT Option is not enabled return H_Function. + + + + If the LIOBN parameter < -128 then return H_Parameter. + + + + If the sum of the count parameter plus |LIOBN| is > 512 then + return H_Parameter. + + + + end + + + + + + If the Shared Logical Resource option is implemented and the TCE + parameter represents a logical page address of a page that has been + rescinded by the owner, return H_RESCINDED. + + + + If the TCE parameter represents the logical page address of a + page that is not valid for the calling partition, return + H_Parameter. + + + + Copy the contents of the page referenced by the TCE table to a + temporary hypervisor page (Temp) for validation without the potential for + caller manipulation. + + + + + + /* Validate the indirect parameters */ + + + + VAL= 0 + + + + If the LIOBN parameter is negative then do + + + + For CNT = 1,|LIOBN|,1 + + + + T = 8 byte entry Temp [VAL] + + + + If the Shared Logical Resource option is implemented and T as an + LIOBN represents a TCE table that has been rescinded by the owner, return + H_RESCINDED. + + + + If T as an LIOBN represents a TCE table that is not valid for the + calling partition, return H_Parameter. + + + + Liobns[VAL+] = T. + + + + If the Shared Logical Resource option is implemented and any of + the I/O bus address range represented the IOBA parameter plus count pages + within the TCE table represented by “T” as an LIOBN + represents a rescinded resource, return H_RESCINDED. + + + + If any of the I/O bus address range represented the IOBA + parameter plus count pages within the TCE table represented by + “T” as an LIOBN is not valid for the calling partition then + return H_Parameter. + + + + loop + + + + + + end + + + + + + + + /* Translate the logical pages addresses to physical*/ + + + + for CNT = 1,count,1 + + + + T = 8 byte entry Temp [VAL+] + + + + If the Page Mapping and Control field of the 8 byte entry + “T” is not “Page Fault” (see + ) then do + + + + If the Shared Logical Resource option is implemented and the + value of “T” as a logical address represents a page that has + been rescinded by the owner, then return H_RESCINDED. + + + + If “T” as a logical address is outside of the range + of calling partition assigned values then return H_PARAMETER. + + + + Translate the logical address within the TCE buffer entry into + the corresponding physical real address. + + + + Temp[CNT - 1] = translated physical real address. + + + + end + + + + + + loop + + + + + + + + /* Fill the TCE table(s) */ + + + + If LIOBN parameter is negative then VAL = |LIOBN| else VAL = + 1. + + + + For TABS = 1, VAL, 1 + + + + The TCE table to fill is that referenced by Liobns[VAL] as an + LIOBN. + + + + INDEX = the page index within the TCE table represented by the + IOBA parameter. + + + + For CNT = 1, count, 1 + + + + TCE_TABLE [Liobns[VAL], INDEX+] = Temp [CNT-1] + + + + Loop + + + + + + Loop + + + + + + Return H_Success. + + + + Implementation Note: The PA requires the OS to issue a sync + instruction to proceed the signaling of an IOA to start an IO operation + involving DMA to guarantee the global visibility of both DMA and TCE + data. This hcall() does not include a sync instruction to guarantee + global visibility of TCE data and in no way diminishes the requirement + for the OS to issue it. + +
+ +
+ +
+ Processor Register Hypervisor Resource Access + Certain processor registers are architecturally hypervisor + resources, in the following cases the hypervisor provides controlled + write access services. + +
+ H_SET_SPRG0 + + + + + Parameters: + + + + value: The value to be written into SPRG0. No parameter checking + is done against this value. + + + +
+ +
+ H_SET_DABR + Note: Implementations reporting compatibility to ISA versions less + than 2.07 are required to implement this interface; however, this + interface is being deprecated in favor of + for newer + implementations. + + + + + Semantics: + + + + If the platform does not implement the extended DABR facility + then: + + + + Validate the value parameter else return H_RESERVED_DABR and the + value in the DABR is not changed: + + + + The DABR BT bit (Breakpoint Translation) is checked for a value + of 1. + + + + + + + + Else (The platform does implement the extended DABR + facility): + + + + Load the DABRX register with 0b0011. + + + + place the value parameter into the DABR. + + + + + + Return H_Success. + + + + +
+ +
+ H_PAGE_INIT + + + + + Parameters: + + + + flags: zero, copy, I-Cache-Invalidate, I-Cache-Synchronize, and + for the CMO option: CMO Option flags as defined in + . + + + + destination: The logical address of the start of the page to be + initialized + + + + source: The logical address of the start of the page use as the + source on a page copy initialization. This parameter is only checked and + used if the copy flag is set. + + + + + + + Semantics: + + + + The logical addresses are checked, they must both point to the + start of a 4 K system memory page associated with the partition or return + H_Parameter. + + + + If the Shared Logical Resource option is implemented and the + source/destination logical page number represents a page that has been + rescinded by the owner, return H_RESCINDED. + + + + + + If the zero flag is set, clear the destination page using a + platform specific routine (usually a series of dcbz instructions). + + + + If the copy flag is set, execute a platform specific optimized + copy of the full 4 K page from the source to the destination. + + + + If I-Cache-Invalidate flag is set, issue icbi instructions for + all of the page’s cache lines + + + + If I-Cache-Synchronize flag is set, issue dcbst and icbi + instructions for all of the page’s cache lines. Implementations may + need to issue a sync instruction to complete the coherency management of + the I-Cache. + + + + For the CMO option: set the page usage state per the CMO Option + flags field of the flags parameter as defined in + . + + + + Return H_Success + + + + Note: For the CMO option, the CMO option flags may be + used to notify the platform of the page usage state of a page without + regard to its hardware page table entry or lack there of independent of + any other option flags. + +
+ +
+ H_SET_XDABR + Note: Implementations reporting compatibility to ISA versions less + than 2.07 are required to implement this interface; however, this + interface is being deprecated in favor of + for newer + implementations. + This hcall() provides support for the extended Data Address + Breakpoint facility. It sets the contents of the Data Address Breakpoint + Register (DABR) and its companion Data Address Breakpoint Register + Extension (DABRX). A principal advantage of the extended DABR facility is + that it allows setting breakpoints for LPAR addresses that the hypervisor + had to preclude using the previous facility. + + + + + Semantics: + + + Validates the extended parameter else return H_Parameter: + + + + Reserved Bits (0-59) are zero. + + + + The HYP bit (61) is off. + + + + The rest of the PRIVM field (Bits 62-63) is one of those + supported: + + + + 0b01 Problem State + + + + 0b10 Privileged non-hypervisor + + + + 0b11 Privileged or Problem State + + + + (Specifying neither Problem or Privileged state is not + supported) + + + + + + + Load the validated extended parameter into the DABRX + + + Load the value parameter into the DABR + + + Return H_Success. + + + +
+ +
+ H_SET_MODE + This hcall() is used to set hypervisor processing resource mode + registers such as breakpoints and watchpoints. The modes supported by the + hardware processor are a function of the processor architectural level as + reported in the + “cpu-version” property. + presents the valid parameter + ranges for the architectural level reported in the + “cpu-version” property. + Setting breakpoints: A breakpoint is set for a hardware tread. + Should the hardware thread complete an instruction who's effective + address matches that of the set breakpoint a trace interrupt is signaled. + When setting the breakpoint resource, the mflags and value2 parameters + are zero. The value1 parameter is the effective address of the breakpoint + to be set. + Setting watchpoints: A watchpoint is set for a hardware tread. + Should the hardware thread attempt to access within the specified double + word range of the effective address specified by the value1 parameter as + qualified by the conditions specified in the value2 parameter a Data + Storage type interrupt is signaled. When setting the watchpoint resource, + the mflags parameter is zero. The value1 parameter is the effective + double word address of the watchpoint to be set. The value2 parameter + specifies the qualifying conditions for the access, these are a subset of + the POWER ISA conditions that are relevant within the context of a + logical partition. This subset includes the MRD field, DW, DR, WT, WTI, + PNH, and PRO bits. All other value2 fields are zero. + Setting Interrupt Vector Location Modes: The Alternate Interrupt + Location (AIL) Mode for the calling partition is set. Since this function + has partition wide scope, it may take longer for the hypervisor to + perform the function on all processors than is permissible during a + synchronous call; therefore, the call might return long busy. In that + case the caller should repeat the call with the same parameters after the + specified time period until the H_SUCCESS return code is received. A call + with different parameters indicates the beginning of a new partition wide + mode setting. The desired AIL mode is encoded in the two low order mflags + bits (all other mflags bits are 0) while both value1 and value2 + parameters are zero. + + + + + Semantics: + switch (resource) { + case 0: /* not used / + return H_P2; + break; + case 1: /* Completed Instruction Address Breakpoint Register + */ + if value2 <> 0 the return H_P4; + if mflags <> 0 then return H_UNSUPPORTED_FLAG; + If low order two bits of value1 are 0b11 then return H_P3; /* not + hypervisor instruction address */ + move value 1 into CIABR; /* note the value2 parameter is not used + for this resource */ + break; + case2: /* Watch point 0 registers */ + if mflags <> 0 then return H_UNSUPPORTED_FLAG; + If value2 bit 61 == 0b1 then return H_P4; /* not hypervisor + addresses */ + move value1 into DAWR0; + move value2 into DAWRX0; + break; + case3: / * Address Translation Mode on Interrupt * / + if value1 < > 0 then return H_P3; + if value2 < > 0 then return H_P4; + switch (mflags) { + case 0: / * IR = DR = 0 * / + Set LPCR AIL field of calling partition processors to 0b00; + break; + case 1: / * reserved * / + return H_UNSUPPORTED_FLAG ( - 318); + break; + case 2: / * IR = DR = 1 interrupt vectors at E.A. 0X18000 * + / + Set LPCR AIL field of calling partition processors to 0b10; + break; + case 3: / * IR = DR = 1 interrupt vectors at E.A. 0XC000 0000 0000 + 4000 * / + Set LPCR AIL field of calling partition processors to 0b11; + break; + default: return H_UNSUPPORTED_FLAG (value based on most + convenient + unsupported bit); + break; + default: + return H_P2; + break; } + + + H_SET_MODE Parameters per ISA Level + + + + + + + + + + + + + ISA level + + + + + Supported Resource Values + + + + + Values Supported mflags + + + + + Value 1 + + + + + Value 2 + + + + + Comments  + + + + + + + + 2.07 + + + 1 + + + None + + + Breakpoint Address + + + None + + +   + + + + + 2 + + + None + + + Watchpoint Double Word Address + + + Watchpoint Qualifying Conditions + + +   + + + + + 3 + + + 0 + + + None + + + None + + + IR=DR=0 No offset + + + + + 1 + + + None + + + None + + + Reserved + + + + + 2 + + + None + + + None + + + IR=DR=1 offset 0x18000 + + + + + 3 + + + None + + + None + + + IR=DR=1 offset 0xC000 0000 0000 4000 + + + + + All Others + + + All Others + + + All Others + + + Reserved + + + + + All Others + + + All Others + + + All Others + + + All Others + + + Reserved + + + + +
+ + + + R1--1. + + For implementations supporting POWER + ISA level 2.07 and beyond: the platform must implement the H_SET_MODE + hcall() per the syntax and semantics of section + . + + + + + +
+
+ +
+ Debugger Support hcall()s + The real mode debugger needs to be able to get to its async port + and beyond the real mode limit register without turning on virtual + address translation. The following hcall()s provide that + capability. + +
+ H_LOGICAL_CI_LOAD + + + + + Parameters: + + + + size: The size of the cache inhibited load: + + + + byte = 1 + + + + half = 2 + + + + full = 4 + + + + double=8 + + + + All other size values are illegal and returns H_Parameter + + + + + + addr: The logical address of the cache inhibited location to be + read. The hypervisor checks that the address is within the range of + addresses valid for the partition, on a boundary equal to the requested + length, is not to the location BA+4 within an interrupt management area, + and mapped as cache inhibited (cache paradoxes are to be avoided)-- Else + H_Parameter. + + + + On successful return (H_Success), the read value is low order + justified in register R4. + + + + +
+ +
+ H_LOGICAL_CI_STORE + + + + + Parameters: + + + + size: The size of the cache inhibited store: + + + + byte = 1 + + + + half = 2 + + + + full = 4 + + + + double=8 + + + + All other size values are illegal and returns H_Parameter + + + + + + addr: The logical address of the cache inhibited location to be + written. The hypervisor checks that the address is within the range of + addresses valid for the partition, on a boundary equal to the requested + length, is not to the location BA+4 within an interrupt management area, + and mapped as cache inhibited (cache paradoxes are to be avoided). + + + + value The value to be written is low order justified in register + R6. + + + + +
+
+ +
+ Virtual Terminal Support + This section has been moved to + . + + Architecture and Implementation Note: The requirement + to provide the + “ibm,termno” property in the + /rtas node, has been removed (it is now necessary to + look for + vty nodes and use their unit address from the + “reg” property to get the same + information). The + “ibm,termno” property called for + sequential terminal numbers, but with the use of unit addresses from the + “reg” property, such is not the + case. +
+ +
+ Dump Support hcall()s + To allow the OS to dump hypervisor data areas in support of field + problem diagnosis the hcall-dump support function set contains the + H_HYPERVISOR_DATA hcall(). This hcall() is enabled or disabled (default + disabled) via the Hardware Management Console. If the hcall-dump function + set is disabled an attempt to make a H_HYPERVISOR_DATA hcall() returns + H_Function. When the function is enabled, the hcall-dump function set is + specified in the + “ibm,hypertas-functions” property. The + requester calls repeatedly starting with a control value of zero getting + back 64 bytes per call and setting the control parameter on the next call + to the previous call’s return code until the hcall() returns + H_Parameter indicating that all hypervisor data has been dumped. The + precise meaning of the sequence of data is implementation dependent. The + H_HYPERVISOR_DATA hcall() need only return data in the firmware working + storage that is not contained in the PFT or TCE tables since the contents + of these tables are available to the OS. + +
+ H_HYPERVISOR_DATA + + + + + Parameters: + + + + control: A value passed to establish the progress of the + dump. + + + + + + Semantics: + + + + If the control value is zero, the data returned is the first + segment of the hypervisor’s working storage, with a non-negative + return code. + + + + If the control value is equal to the return code of the last + H_HYPERVISOR_DATA call, and the return code is non-negative, the data + returned in R4 through R11 is the next sequential segment of the + hypervisor’s working storage. The contents of R4 through R11 are + undefined if the return code is negative. + + + + Implementation Note: It is expected that the control + value is be used by the H_HYPERVISOR_DATA routine as an offset into the + hypervisor’s data area. For the expected implementation, hypervisor + checks the value of the control parameter to insure that the resultant + pointer is within hypervisor’s data area else it returns + H_Parameter. + +
+
+ +
+ Interrupt Support hcall()s + Injudicious values written to the interrupt source controller may + affect innocent partitions. The following hcall()s monitor the + architected functions. + +
+ H_EOI + + Software Implementation Note: Issuing more H_EOI + calls than actual interrupts may cause undesirable behavior, including + but not limited to lost interrupts, and excessive phantom + interrupts. + + + + + Parameters: + + + + xirr: The low order 32 bits is the value to be written into the + calling processor’s interrupt management area’s external + interrupt request register (xirr). + + + + + + Semantics: + + + + If the platform implements the Platform Reserved Interrupt + Priority Level Option, and the priority field of the xirr parameter + matches one of the reserved interrupt priorities then return + H_Resource. + + + + If the value of the xirr parameter is such that the low order 3 + bytes (xisr) is one of the interrupt source values assigned to the + partition, and the high order byte xirr byte (cppr) is equal or less + favored than the current cppr contents, then the value is written into + the calling processor’s xirr causing the interrupt source + controller to signal an “end of interrupt” (EOI) to the + specified interrupt source logic, then hypervisor returns H_Success or + H_Hardware (if an unrecoverable hardware error occurred). If the xirr + value is not legal, hypervisor returns H_Parameter. + + + + If the Shared Logical Resource option is implemented and the xirr + parameter represents a shared logical resource location that has been + rescinded by the owner, return H_RESCINDED. + + + + + +
+ +
+ H_CPPR + + + + + Parameters: + + + + cppr: The low order byte is the value to be written into the + calling processor’s interrupt management area’s current + processor priority register (cppr). + + + + + + Semantics: + + + + If the platform implements the Platform Reserved Interrupt + Priority Level Option, and the priority field of the xirr parameter + matches one of the reserved interrupt priorities then return + H_Resource. + + + + The value of the cppr parameter is written into the calling + processor’s cppr causing the interrupt source controller to reject + any interrupt of equal or less favored priority. Then hypervisor returns + H_Success or H_Hardware (if an unrecoverable hardware error + occurred). + + + +
+ +
+ H_IPI + + + + + Parameters: + + + + server#: The server number gotten from the + “ibm,ppc-interrupt-server#s” + property associated with the processor and/or thread + to be interrupted. + + + + mfrr: The priority value the inter-processor interrupt to be + signaled. + + + + + + Semantics: + + + + If the platform implements the Platform Reserved Interrupt + Priority Level Option, and the priority field of the xirr parameter + matches one of the reserved interrupt priorities then return + H_Resource. + + + + If the value of the server# parameter specifies of one of the + processors in the calling processor’s partition, then the value in + the low order byte of the mfrr parameter is written into the mfrr + register (BA+12) of the processor’s interrupt management area + causing that interrupt source controller to signal an + “inter-processor interrupt” (IPI) to the processor associated + with the specified interrupt management area. Hypervisor then returns + H_Success or H_Hardware (if an unrecoverable hardware error occurred). If + the server# value is not legal, hypervisor returns H_Parameter. + + + + If the Shared Logical Resource option is implemented and the + server# parameter represents a shared logical resource location that has + been rescinded by the owner, return H_RESCINDED. + + + + + + +
+ +
+ H_IPOLL + + + + + Parameters: + + + + server#: The server number gotten from the + “ibm,ppc-interrupt-server#s” + property associated with the processor and/or tread + to be interrupted. + + + + + Semantics: + + + + If the value of the server# parameter specifies of one of the + processors in the calling processor’s partition, then hypervisor + reads the 4 byte contents of the processor’s interrupt management + area port at offset BA+0 into the low order 4 bytes of register R4 and + the one byte of the mfrr (BA+12) into the low order byte of R5. Reading + these addresses has no side effects and is used to poll for pending + interrupts. Hypervisor then returns H_Success or H_Hardware (if an + unrecoverable hardware error occurred). If the server# value is not + legal, hypervisor returns H_Parameter. + + + + If the Shared Logical Resource option is implemented and the + server# parameter represents a shared logical resource location that has + been rescinded by the owner, return H_RESCINDED. + + + + + +
+ +
+ H_XIRR / H_XIRR-X + These hcall()s provide the same base function that is they return + the interrupt source number associated with the external interrupt. + H_XIRR-X further supplies the time stamp of the interrupt . Legacy + implementations implement only H_XIRR, returning H_Function for a call to + H_XIRR-X. POWER8 implementations also implement H_XIRR-X. + + + + + Parameters: + + + + H_XIRR: no input parameters defined. + + + + H_XIRR-X: cppr: the internal current processor priority of the + calling virtual processor. Valid values in the range of 0x00 - most + favored to 0xFF - least favored less those values specified by the + “ibm,plat-res-int-priorities” property in + the root node). + + + + + + Semantics: + + + + Hypervisor reads the 4 byte contents of the processor’s + interrupt management area port at offset BA+4 into the low order 4 bytes + of the register R4. Reading this address has the side effect of accepting + the interrupt and raising the current processor priority to that of the + accepted interrupt. + + + + Place the timestamp when the hypervisor first received the + interrupt into R5. + + + + Hypervisor then returns H_Success or H_Hardware (if an + unrecoverable hardware error occurred). + + + +
+
+ +
+ Memory Migration Support hcall()s + To assist an OS in memory migration, the following hcall() is + provided. During the migration process, it is the responsibility of the + OS to not change the DMA mappings referenced by the translations buffer + (for example by using the H_GET_TCE, H_PUT_TCE hcall()s, or other DMA + mapping hcall()s). Failure of the OS to serialize such DMA mapping access + may result in undesirable DMA mappings within the caller’s + partition (but not outside of the caller’s partition). Further, it + is the responsibility of the OS to serialize calls to the H_MIGRATE_DMA + service relative to the logical bus numbers referenced. Failure of the OS + to serialize relative to the logical bus numbers may result DMA data + corruption within the caller’s partition. + On certain implementations, DMA read operations targeting the old + page may still be in process for some time after the H_MIGRATE_DMA call + returns; this requires that the OS not reuse/modify the data within the + old page until the worst case DMA read access time has expired. The + “ibm,dma-delay-time” property (see + ) gives the OS this implementation + dependent delay value. Failure to observe this delay time may result in + data corruption as seen by the caller’s I/O adapter(s). + + + + R1--1. + + For the LPAR option supporting the hcall-migrate function + set: The platform must supply the + “ibm,dma-delay-time” property under the + /rtas node of the device tree. + Memory pages may be simultaneously mapped by multiple DMA agents, + with different translation table formats and operation characteristics. + The H_MIGRATE_DMA hcall() atomically performs the memory migration + process so that the new page contains the old page contents (as updated + by any DMA write operations allowed during migration), with all DMA + mappings and engines directed to access the new page. The entries in the + mapping list contain the logical bus number associated with the mapping + and the I/O address of the mapping. From these two data, the hcall() + associates the using DMA agent, that agent’s DMA control + procedures, the specific mapping table and mapping table entry. + + + + + R1--2. + + For the LPAR option supporting the hcall-migrate function + set: The platform must support migration of pages mapped for + DMA using any of the platform supported DMA agents. + + + + + R1--3. + + For the LPAR option supporting the hcall-migrate function + set: All the platform’s DMA agents must support + mechanisms that enable the platform to meet the syntax, semantics and + requirements set forth in section 14.5.4.8.1. + + Implementation Note: The minimal hardware mechanisms + to support the hcall-migrate function set are to quiesce DMA operation, + flush outstanding data to their targets (both reads and writes), modify + their DMA mapping and re-enable operation utilizing said modified DMA + mapping without introducing unrecoverable operational failures. Provision + for the hardware to direct DMA write operations to both old and new pages + provides a significantly more robust implementation. + It is the intent of this architecture to have all memory in the + platform have the capability to be migrated. However, on the rare + implementation that cannot meet that intent, the + “ibm,no-h-migrate-dma” property may be + provided in + memory nodes for which H_MIGRATE_DMA cannot be + implemented. + + + + + R1--4. + + For the LPAR option supporting the hcall-migrate function + set: If a memory node cannot support H_MIGRATE_DMA, then that + memory node must contain the + “ibm,no-h-migrate-dma” property. + For the I/O Super Page option the I/O page size is an attribute of + the specified LIOBN (I/O pages mapped by a given LIOBN are a uniform + size), also the syntax and semantics of H_MIGRATE_DMA are extended to + allow migration of I/O pages that are larger than 4K bytes and have more + than 256 xlates translation entries. Specifying more than 256 translation + entries requires a sequence of calls to H_MIGRATE_DMA with the same + “newpage” address. Making a call in the sequence with a + length parameter of zero terminates the operation - should this + termination happen after the start of the physical migration, the + resulting state of the calling partition’s memory is unpredictable. + Failure to make a continuing call in the sequence for more than one + second aborts the operation; again the resulting state of the calling + partition’s memory is unpredictable. + The introduction of super pages introduces the case where portions + of the super page may be I/O mapped and thus require the use of + H_MIGRATE_DMA to move the logical super page from one physical page to + another even though the super page as a whole may not be I/O mapped. To + handle this case, the LIOBN value of 0xFFFFFFFF is reserved to allow the + specification, within an translations entry (passed to H_MIGRATE_DMA via + the xlates parameter), of a super page that is not currently I/O mapped. + In this case, the normally reserved byte at xlates entry offset 4 is used + to specify the power of two size of the super page. + + + + + R1--5. + + For the I/O Super Page option: the platform must + support the setting by the client of byte 3 bit 0 of the + ibm,architecture.vec 5 as input to the + ibm,client-architecture-support method. + + + + + +
+ H_MIGRATE_DMA + + + + + + Parameters: + + + + newpage (The Logical address of the new page to be the target of + the TCE translations) + + + + xlates (The Logical address of a list of translations against the + target page the format of this list is: + + + + List starts on a page (4 K) boundary. + + + + Contains up to 256 translation entries: + + + + First 4 bytes of a translation entry is the logical bus number as + from either the: + + + + “ibm,dma-window” property + + + + or the reserved LIOBN 0xFFFFFFFF. + + + + + + Next 12 bytes of a translation entry is the logical bus offset + (I/O bus address). The format of the I/O bus address is dependent upon + the DMA agent: + + + + For 32 bit PCI, the high order 8 bytes are reserved with the low + order 4 bytes containing a 4 K aligned address (low order 12 bits + =zero). + + + + For 64 bit PCI, the high order 4 bytes are reserved with the low + order 8bytes containing a 4 K aligned address (low order 12 bits + =zero). + + + + For the I/O Super Page option the very first translation entry + passed is for the largest I/O page to be migrated by this sequence of + calls; else all translation entries are for the single 4K byte logical + page being migrated. The first translation entry may either be a current + I/O mapping for the largest I/O page that the caller wishes to migrate, + or the first translation entry may use the reserved LIOBN number of + 0xFFFFFFFF, with the next byte indicating the page size as 2**N where N + is the numeric value of the byte at offset 4 into the translation entry + with the low order 8 bytes of the translation entry being the logical + real address of the start of the page to be migrated (the low order N + bits = zero). + + + + + + + + + + length (Number of entries in translation list is less than or + equal to 256) + + + + If the total number of translation entries in the xlates list is + less than or equal to 256 then the “length” parameter is the + number of translation entries. + + + + For the I/O Super Page option and specifying more than 256 + translation entries, the client makes a series of calls, each passing 256 + translation entries with the “length” parameter being the + negative of the total number of translation entries yet to be passed + until there are less than or equal to 256 remaining then for the final + call in the initiating sequence the “length” parameter is + positive as above. + + + + + + + + + Semantics: + + + + For the I/O Super Page option: determine if a migration operation + is in process for this “newpage” address: + + + + Then: + + + + If the previous hcall() for the migration operation was more than + 1 second ago, return H_Aborted. + + + + If the length parameter value is zero then abort the migration + operation and return H_TERM. + + + + If the length parameter value is not the next expected in the + sequence return H_P3. + + + + Record the new xlates + + + + If the length parameter is less than zero return + H_CONTINUE. + + + + + + Else + + + + If the number of outstanding operations is more than an + implementation specific number as communicated in the + “ibm,vec-5” property then return + H_Resource + + + + If the length parameter is less than zero, initiate a new + migration operation for the “newpage” address. (Note + resources for the operation may be allocated at this point and freed when + the operation terminates either normally, in error, or via timeout. + Implementations may, in unusual cases, use a busy return code to wait for + the release of resources from an immanently completing operation. + + + + The first xlate entry specifies the length and starting address + of the page to be migrated, if this specification is invalid (unsupported + length, the address is invalid for the partition, or not aligned to the + length) return H_MEM_PARM. + + + + If the operation specifies more than an implementation specific + number of xlates as communicated in the + “ibm,vec-5” property then return + H_Resource. + + + + + + + + Check that the page to be migrated can be migrated, else + H_PARAMETER. + + + + Check that the newpage is within the allocated logical page range + of the calling partition and the address is aligned to the I/O page size + of the first translation entry passed else H_PARAMETER. + + + + If the Shared Logical Resource option is implemented and the + newpage parameter represents a shared logical resource location that has + been rescinded by the owner, return H_RESCINDED. + + + + + + The contents of the xlates buffer are checked. + + + + This may be done as each entry is used, or it may be done prior + to starting the operation. + + + + If the former, then partial processing must be backed out in the + case of a detected parameter error. + + + + If the later, then the translation entries must be copied into an + area that is not accessible by the calling OS to prevent parameter + corruption after they have been verified. The OS perceived reentrancy of + the function is not diminished if this option is chosen. + + + + + + The xlates buffer starts on a 4 K boundary within the + partition’s logical address range else H_PARAMETER. + + + + The length parameter is between (for the I/O Super Page option: + the negative of the maximum number of xlate entries supported as + indicated in the + “ibm.architecture-vec-5” property of the + /chosen device tree node else 1) and 256 else + H_PARAMETER. + + + + For the I/O Super Page option: the length of the physical page to + be migrated is the length of the I/O page of the first translation entry; + else the length of the physical page to be migrated is 4K bytes. + + + + Each translation originally references the same physical page, or + a portion there of, else H_PARAMETER. + + + + Each logical bus offset is within the allocated range of the + calling partition else H_PARAMETER. + + + + If the Shared Logical Resource option is implemented and the + logical bus offset represents a shared logical resource location that has + been rescinded by the owner, return H_RESCINDED. + + + + + + Check the logical bus number: + + + + Is allocated to the calling partition else H_PARAMETER. + Or: If the Shared Logical Resource option is implemented and the + logical bus number represents a shared logical resource location that has + been rescinded by the owner, return H_RESCINDED. + + + + For the I/O Super Page option: if the LIOBN implies a larger page + size than that specified by the first translation entry for this migrate + operation, place the index of the translation entry (0-255) into register + R4 and return H_PGSB_PARM. + + + + If the LIOBN referenced an unsupported DMA agent, place the index + of the translation entry (0-255) into register R4 and return + H_Function. + + + + If the logical bus number is not supported, return + H_PARAMETER. + + + + Note: The following is written from the perspective + of a PCI DMA agent; other DMA agents may require a different sequence of + operations to achieve equivalent results. + + + + + + The hypervisor disables arbitration for the IOA(s) associated + with the translation entries. (In some cases, where multiple IOAs share a + given TCE range, arbitration must be disabled for multiple IOAs. The + firmware assigned the bus address ranges to each IOA so knows which IOAs + correspond to which translation.) + + + + Waits for outstanding DMA write activity to complete. (This is + accomplished by doing a load from an appropriate register the bridge(s) + closest to the IOA -- when the load completes (dependency on load data is + satisfied) all DMA write activity has completed.) + + + + The hypervisor copies the contents of the 4 K page originally + accessed by the TCE(s) to the page referenced by the newpage + value. + + + + The hypervisor translates the logical address within the newpage + parameter and stores the resultant value in the TCE table entries + specified by the translation entries. + + + + Executes a sync operation to ensure that the new TCE data is + visible. + + + + The hypervisor enables arbitration on the IOA(s) associated with + the translation entities and returns H_Success. + + + + Implementation Notes: + + + + The firmware should be written to minimize the arbitration + disable time. The old page should be read into cache (possibly using the + data cache touch operations) prior to disabling the arbitration. + Implementation dependent algorithms can significantly improve the page + copy time. + + + + The firmware does not have to serialize this hcall() with other + hcall()s as long as it updates the TCE using atomic eight (8) byte write + operations. However, if the OS does not serialize this call with + H_PUT_TCE to the same TCE, and with other H_MIGRATE_DMA calls to the same + IOA(s) the calling LPARs DMA buffers could be corrupted. + + + + To minimize the effect of such unsupported DMA agents, the + platform designer should isolate such agents on their own bus with their + own “ibm,dma-window” property + specification. + + + +
+
+ +
+ Performance Monitor Support hcall()s + + +
+ H_PERFMON + To manage the Performance Monitor Function: + + + + + Parameters: + + + + mode-set Platform specific modes to be set by this call + + + + mode-reset Platform specific modes to be reset by this + call + + + + + + Semantics: + + + + mode-set bit(s) check for platform specific validity else + H_PARAMETER + + + + mode-reset bit(s) check for platform specific validity else + H_PARAMETER + + + + if any mode-set bits are set, activate corresponding mode(s) - if + logically capable else H_RESOURCE + + + + if any mode-reset bits are on, deactivate corresponding mode(s) - + if logically capable else H_RESOURCE + + + + place current state of platform specific modes in R4, return + H_Success + + + + + + Defined Perfmon mode bits: + bit 0: 1= Enable Perfmon + bit1: 0= Low threshold granularity 1= High threshold + granularity + +
+
+ +
+ H_GET_DMA_XLATES_LIMITED + This hcall returns the I/O bus address of the first entry defined + for the specified LIOBN and the corresponding logical address within the + range beginning with the Start logical address and less than the End + logical addresses, the search is limited to the range of I/O bus + addresses specified by the SIOBA and EIOBA parameters. + + + + R1--1. + + For the LRDR Option: The platform must implement the + H_GET_DMA_XLATES_LIMITED hcall() per the syntax and semantics specified + in section + . + + + + + R1--2. + + For the LRDR Option: The platform must present the + “ibm,h-get-dma-xlates-limited-supported” property in + all PCI host bridge OpenFirmware nodes for which the + H_GET_DMA_XLATES_LIMITED hcall() is supported for all child + LIOBNs. + + + + + + Syntax: + + + + + + + Parameters: + + + + Register R4: Logical I/O Bus Number (LIOBN) + + + + Bits 0-31are reserved and set to zero. + + + + Bits 32-63 contain a 32-bit unsigned binary integer that + identifies a translation which may have one or more entries that + translate to a page within a range specified by the Start and End logical + addresses. + + + + + + Register R5: Start Logical Address (SLA) + + + + Register R6: End Logical Address (ELA) + + + + Register R7: Start I/O Bus Address (SIOBA) of the translation + specified by the LIOBN + + + + The SIOBA register may specify a special value of -1 or a + starting IOBA + + + + + + Register R8: End I/O Bus Address (EIOBA) of the translation + specified by the LIOBN + + + + The EIOBA register may specify a special value of -1 or an ending + IOBA + + + + + + + + Semantics: + + + + Check that the specified LIOBN is supported and allocated to the + calling logical partition, else H_PARAMETER. + + + + Check that the specified start logical address (SLA) is within + the allocated range of the calling logical partition, and is designated + on a 4 K-byte boundary, else H_P2. + + + + Check that the End logical address (ELA) minus 4K is within the + allocated range of the calling logical partition, and is designated on a + 4 K-byte boundary, else H_P3. (May point no further than one page beyond + the maximum partition logical real address in order to stay within the + partition yet include the last partition page in the range of the + test.) + + + + Check that the specified starting logical address (SLA) is less + than the specified ending logical address (ELA), else H_P2. + + + + Check that the page specified by the logical addresses within the + specified range is within the allocated range of the calling logical + partition and the address is 4 K-byte aligned else H_P2. + + + + Check the content of SIOBA + + + + If a value other than -1 is specified, check that the specified + start I/O bus address (SIOBA) is not outside of the range of IOBAs for + the specified LIOBN, else H_P4. + + + + If the SIOBA specifies a value of -1, the hypervisor starts the + search at the lowest IOBA in the translation table, otherwise the search + starts at the address specified by the SIOBA. + + + + + + Check the content of EIOBA + + + + If a value other than -1 is specified, check that the specified + ending I/O bus address (EIOBA) is not outside of the range of IOBAs for + the specified LIOBN, else H_P5. + + + + If the EIOBA specifies a value of -1, the hypervisor ends the + search at the highest IOBA in the translation table, otherwise the search + ends at the address specified by the EIOBA. + + + + + + + + + Outputs: + Place the I/O bus address and corresponding logical address into + the respective registers: + + + + Register R4: I/O Bus Address (IOBA) + + + + This register contains a 64-bit unsigned binary integer that + specifies the I/O bus address of the page within the specified logical + address range for the specified LIOBN. + + + + The IOBA is returned when the hcall() completes with either + H_PARTIAL, H_PAGE_REGISTERED, or H_IN_PROGRESS return codes. + + + + + + Register R5: Corresponding Logical Address (CLA) + + + + This register contains a 64-bit unsigned binary integer that + designates the logical address of a page within the specified range that + corresponds to the I/O bus address. + + + + If the hcall() completes with H_IN_PROGRESS return code, the + corresponding logical address (CLA) is not returned. + + + + + + When the hcall() completes with H_PARTIAL or H_PAGE_REGISTERED + return code: + + + + The I/O bus address (IOBA) and corresponding logical address + (CLA) are returned. + + + + + + When the hcall() completes with H_PAGE_REGISTERED return + code: + + + + The I/O bus address (IOBA) is for the final page of the + translation table for the specified LIOBN as limited by the EIOBA + parameter. + + + + + + When the hcall() completes with H_IN_PROGRESS return code: + + + + The current IOBA being searched against the specified range is + returned, but the corresponding logical address is not returned. + + + + The hcall can be reissued by specifying the IOBA as the starting + IOBA without incrementing the IOBA by the resource page size. + + + + + + + Firmware Implementation Notes: + + + + When the H_GET_DMA_XLATES_LIMITED hcall() is issued, the + hypervisor searches the translation table designated by the specified + LIOBN, from the entry for SIOBA through the entry for EIOBA in IOBA + order, for the entries that translate to a page within a given range of + logical addresses. If an entry is found, the hcall() completes with the + H_PAGE_REGISTERED return code if the page found is the last entry in the + translation table, or the H_PARTIAL return code for all other pages, and + the IOBA with the corresponding logical address are returned in output + registers R4 and R5 respectively. + + + + The hypervisor searches the translation table in IOBA order, and + proceeds in that order until an entry that translates to a physical + address within the specified range of logical addresses is found, in + which case, the hcall() completes with H_PARTIAL or H_PAGE_REGISTERED + return code, or H_Success, if the end of the translation table, as + specified by the EIOBA parameter, is reached. + + + + Software Implementation Notes: + + + + When the hcall() completes with H_PARTIAL return code, the + stored IOBA is incremented by the page size of the resource corresponding + to the specified LIOBN, and then specified as the starting I/O bus + address on a subsequent call where the hypervisor would then proceed with + the search until the end of the translation table, specified by the EIOBA + parameter, is reached. The caller can accumulate a full list of the IOBAs + for the specified LIOBN that translate into the specified range of + logical addresses, which then forms part of the xlate translation entries + specified as an input to the H_MIGRATE_DMA function. + + + + When the hcall() completes with H_PAGE_REGISTERED return code, + this indicates that page is contained in the specified range of logical + addresses, and it is the last page of the translation table such that the + search for that LIOBN is complete. + + + + If a value other than -1 is specified in the starting I/O bus + address register, the program should check that the specified SIOBA value + is not the same as the returned IOBA. + + + +
+
+
+ +
+ RTAS Requirements + RTAS function as specified in this architecture is still required for + LoPAR LPAR partition. RTAS is instantiated via an OF client interface + call. RTAS operates without memory translation, therefore, the OS should + instantiate it within the RMA, however, the OF client interface does not + enforce this limitation. The RTAS calling sequences remain unchanged. + However, in LPAR configurations RTAS code is implemented differently than + in non-LPAR systems. LPAR RTAS has a part which is replicated in each + partition, and since RTAS has the capability to manipulate hardware system + resources, RTAS has a part which is implemented in the hypervisor. In the + hypervisor, there is a check of the RTAS parameters for validity before + execution. Therefore, the function of the partition replicated RTAS call is + to martial the arguments and make the required hidden hcall()s to the + hypervisor. In a non-LPAR system, RTAS calls are assumed to be made with + valid parameters. This cannot be assumed with LPAR. The LPAR RTAS operates + by all the rules of non-LPAR RTAS relative to it running real, with real + mode pointers to arguments and the same serialization requirement relative + to a single partition. However, the hypervisor may not assume that the + caller is following these serialization rules, failure on the part of the + OS to properly serialize is allowed to cause unpredictable results within + the scope of the calling partition but may not affect the proper operation + of other platform partitions. + The following is a list of RTAS functions that are not defined or + implemented when the LPAR option is active: + + + + restart-rtas + + + + R1--1. + + For the LPAR option: The platform must implement the + PowerPC External Interrupt option. + + + + + R1--2. + + For the LPAR option: The Firmware must initialize each + processor’s interrupt management area’s CPPR to the most + favored level and its MFRR to the least favored level before passing + control of the processor to the OS. + + + + + R1--3. + + For the LPAR option: The RTAS rules of serialization of + RTAS calls must only apply to a partition and not to the system. + + + + + R1--4. + + For the LPAR option: The hypervisor cannot trust the + RTAS calls to have no errors, therefore, the hypervisor must check a + partition’s RTAS call parameters for validity. + + + + + R1--5. + + For the LPAR option: RTAS must be instantiated within + the RMA of partition storage. + + + + + R1--6. + + For the LPAR option: + RTAS arguments must + be within the RMA of partition storage unless specifically specified in the + RTAS call definition. + + + + + R1--7. + + For the LPAR option: If one or more hcalls fail due to + hardware error (return status -1), the platform must make available, prior + to the completion of the next boot sequence, via an + event-scan/check-exception, an error log indicating + the hardware FRU responsible for such failures. Due to the asynchronous + nature of error analysis, there is not a direct correlation between the log + and a specific failing hcall(), indeed the error log may precede the + failing hcall(). + + + + + + + +
+
+ OF Requirements + The hypervisor is initialized and configured prior to the loading of + OF into the partition and boot of any client program (OS) in the partition + by OF. The NVRAM data base that describes the platform’s partitioning + is used to trigger the loading and initialization of the hypervisor. When + Logical Partitioning is enabled, a copy of OF code is loaded into each + partition where it builds the per partition device tree within the + partition’s RAM. The per partition device tree contains only entries + for platform components actually assigned to or used by the partition. The + invocation of the subset of the OF Client interface specified below appears + the same to the OS image regardless of the state of the LPAR option. + A model of the boot sequence is as follows: + + + + Support processor runs chip tests and configures the CPU + chips. + + + + The support processor loads the boot ROM image into System Memory + along with the configuration information. + + + + POST code + + + + Initialization Firmware + + + + Hardware configuration reporting structures + + + + OF + + + + Hypervisor RTAS + + + + + + boot ROM executes POST and Initialization Firmware. + + + + Processor initialization code synchronizes the time bases of all + platform processors to a small value (approaching zero). + + + + Initialization Firmware accesses the NVRAM Partition Database to + determine if the LPAR option is enabled. + + + + Initialization Firmware initializes the hypervisor. + + + + The hypervisor configures itself using the hardware configuration + reporting structures. + + + + The hypervisor configures the various partitions with resources as + required by the NVRAM Partition Database. + + + + The hypervisor loads a copy of OF into each partition passing to + OF a resource reporting structure known as the NACA/PACA. + + + + OF notices in the NACA/PACA that a specific partition table is + specified. + + + + OF Scans the configuration and walks the buses to build the + partition device tree. + + + + OF requests the specific partition table from the NVRAM Partition + Database. + + + + OF loads RTAS into the partition’s memory. + + + + OF pulls in the configuration variables from the + partition’s NVRAM area and uses them to determine the + partition’s boot device. + + + + OF then loads the client program and starts executing it with one + of the partition’s processors. + + + + The client program notices that it is running on a LPAR capable + machine but does not have the hypervisor bit on in the MSR so must use + hcall() routines for its PFT and TCE accesses. The presence of the + “ibm,hypertas-functions” property is a + duplicate indication of LPAR mode. + + + + + + R1--1. + + For the LPAR option: The OF code state must be retained + after all partitions are initialized pending future boot requests. + + + + + R1--2. + + For the LPAR option: The OF code must recognize that + logical partitioning is required as opposed to a non-LPARed system. + + + + + R1--3. + + For the LPAR option: The OF must generate the device + tree for the partition within the partition’s RAM. + + + + + R1--4. + + For the LPAR combined with Dynamic Reconfiguration + option: The + “interrupt-ranges” property for any + reported interrupt source controller must report all possible interrupt + source numbers. + + + + + R1--5. + + For the LPAR option: The OF device tree for a partition + must include in the root node, the + “ibm,partition-no” property. + + + + + R1--6. + + For the LPAR option: The OF device tree for an LPAR + capable model not running in a partition must include in the root node, the + “ibm,partition-no” property when the + default partition number for the first partition created is not 1. + + + + + R1--7. + + For the LPAR option: The + “ibm,partition-no” property value must be + an integer in the range of 1 to 220-1. + + + + + R1--8. + + For the LPAR option: The OF device tree for a partition + must include in the root node, the + “ibm,partition-name” property. + + + + + R1--9. + + For the LPAR option: When the platform does not provide + a partition manager and the one and only partition in the system owns all + the partition visible system resources, then the default value of the + “ibm,partition-name” property must be the + content of the SE keyword (as displayed in the same form as the root node + “system-id” property) with a hyphen added + between the plant of manufacture and sequence number. + + + + + R1--10. + + For the LPAR option: The nodes of the OF device tree + for a partition that represent platform resources that are not explicitly + allocated for the control of the platform’s OS image must be marked + “used-by-rtas”. This includes, but is not limited to, memory + controllers, and IO bridges that are a part of the platform’s + infrastructure common to more than one partition and commonly represented + in the OF device tree. But does not include read only resources such as + environmental sensors. + + + + + R1--11. + + For the LPAR option: The OF must, at the OS’s + request, load the required RTAS into the partition’s real addressable + memory region. + + + + + R1--12. + + For the LPAR option: The OF must use the + partition’s segment of the NVRAM to establish the partition’s + boot device and configuration variables. + + + + + R1--13. + + For the LPAR option: The OF must load the client + program and choose the partition’s processor on which to begin + execution. + Note: It is the responsibility of the client program to recognize + whether or not to use LPAR page management. + + + + + R1--14. + + For the LPAR option: The platform must initialize the + time base of the first processor to a small (approaching zero) value prior + to turning over control of the processor to a client program. + + + + + R1--15. + + + Reserved + + + + + R1--16. + + For the LPAR option: The OF Client Interface must + restrict access to only resources contained within the calling + partition’s version of the device tree. + + + + + R1--17. + + For the LPAR option: The OF Client Interface must + prevent the calls of one partition’s client program from interfering + with the operation of another partition’s client program. + + + + + R1--18. + + For the LPAR option: The OF Client Interface must + restrict its supported calls and methods to those specified in + . + + + + + R1--19. + + For the LPAR option: Any hidden hcall()s which firmware + may use to implement OF functions must check its parameters to insure + compliance with all of the architecturally mandated OF requirements. + + + + + R1--20. + + For the LPAR option: The OF Client Interface functions + “start-cpu” and “resume-cpu” must restrict their + operation to processors assigned to the calling Client’s + partition. + + + + + + OF Client Interface Functions Supported under the LPAR + Option + + + + + + + + + + test + + + cannon + + + child + + + finddevice + + + + + getprop + + + getproplen + + + instance-to-package + + + instance-to-path + + + + + nextprop + + + package-to-path + + + parent + + + peer + + + + + setprop + + + call-method + + + test-method + + + close + + + + + open + + + read + + + seek + + + write + + + + + claim + + + release + + + boot + + + enter + + + + + exit + + + start-cpu + + + milliseconds + + + size(/chosen/nvram) + + + + + get-time + + +   + + + instantiate-rtas + + +   + + + + +
+
+
+ NVRAM Requirements + The NVRAM is divided into multiple partitions each containing + different categories of data similar to files in a file system (these NVRAM + partitions are not to be confused with LPAR partitions). Each NVRAM + partition is structured with a self identifying header followed by its + partition unique data. Many of these NVRAM partitions contain data only + relevant to the platform firmware, while others contain data that either is + for OS image use from boot to boot or is used to communicate operational + parameters from the OS image to the platform. The platform firmware on LPAR + supporting platforms structures the NVRAM as per + . Each LPAR partition is assigned + a region of NVRAM space. This includes space for LPAR partition specific + configuration variables as well as the minimum 4 K space reserved for the + OS image. The hypervisor restricts access for the LPAR partition, through + logical address translation and range checking, to its assigned NVRAM + region. Other regions of NVRAM are reserved for firmware use including, for + instance, information about how the system should be partitioned. + + + LPAR NVRAM Map + + + + + + + + + + Real Address Range + + + + + Per Partition NVRAM access routine rtas + call Logical Address Range -- outside of legal range return + 0x00 and discard write data. + + + + + Contents + + + + + + + + 0x00 to F-1 + + + NA + + + Firmware only partitions (Signatures 0x00 to 0x6F) + + + + + F to (F-1+P) + + + 0x00 to P + + + Per LPAR partition copies of supported NVRAM partitions + with signatures 0x70 to 0x7F + + + + + (F+P) to (F-1+2P) + + + 0x00 to P + + + Per LPAR partition copies of supported NVRAM partitions + with signatures 0x70 to 0x7F + + + + + ... + + + + + (F+(P*(n-1))) + to + ((F-1)+ nP) + + + 0x00 to P + + + Per LPAR partition copies of supported NVRAM partitions + with signatures 0x70 to 0x7F + + + + +
+   + + NVRAM partitions on LPAR platforms + + + + + + + + + + Visible to: + + + + + Partition Signatures + + + + + Partition Name + + + + + Comments + + + + + + + + Only to the Platform firmware + + + 0x00 - 0x6F + + +   + + +   + + + + + Only to Platform firmware and the OS image running in the + owning LPAR Partition. + The read and write NVRAM RTAS routines + + + 0x70 + + + Common + + + This partition is duplicated per partition. + + + + + 0x7F + + + 0x7777777777777777-77777777 + + + This partition is duplicated per partition and is at least + 4 KB long when the OS is first installed. + + + + +
+ + + + R1--1. + + For the LPAR option: Platform OF must locate + configuration variables that the OS must manipulate to select options as to + how the specific OS image interfaces or relates to the platform in the + partition’s “system” partition signature (0x70) named + “common”, specifically none may be located in the + “OF” signature (0x50). + + + + + R1--2. + + For the LPAR option: The NVRAM region assigned to an + LPAR partition must contain, after any platform required NVRAM partitions + have been allocated, a free space partition a minimum of 4 KB long prior to + the installation of the partition’s OS image. + + + +
+ +
+ Administrative Application Communication Requirements + The platform needs to communicate with the an administrative + application (outside of the scope of LoPAR) to manage the platform + resources. The administrative application may run in an external computer + such as a Hardware Management Console, or it may be integrated into a + service partition. Many system facilities are not dedicated to an LPAR + partition but are managed through the HMC and the administrative + application. + + + + R1--1. + + For the LPAR option: The platform must provide a + communications means to the administrative application. + + + + + R1--2. + + For the LPAR option: The platform must respond to + messages received from the administrative application. + + + +
+ +
+ RTAS Access to Hypervisor Virtualized Resources + All allolcatable platform resources are always assigned to a + partition. There always exists a dummy partition that is never active. + Resources assigned to partitions that are inactive may be reassigned to + other partitions by mechanisms implemented in the Hardware Management + Console. + + + + R1--1. + + For the LPAR option: The nvram-fetch RTAS call must + restricted access to only the LPAR partition’s assigned + “OS”, “System” and “Error Log” nvram + partitions. + + + + + R1--2. + + For the LPAR option: The nvram-store RTAS call must + restricted accss to only the LPAR partition’s assigned + “OS”, “System” and “Error Log” nvram + partitions. + + + + + R1--3. + + For the LPAR option: The get-time-of-day RTAS call must + return the LPAR partition’s specific time of day clock value. + + + + + R1--4. + + For the LPAR option: The set-time-of-day RTAS call must + set the LPAR partition’s specific time of day clock value. + Firmware Implementation Note: The model implementation keeps time of + day on a partition basis. What is really changed is the offset from the + hardware TOD clock which is not normally written (Only written if for some + reason it is approaching its maximum value, such as after a battery + failure). + + + + + R1--5. + + For the LPAR option: The event-scan RTAS call must + report global events to each LPAR partition and LPAR partition local events + only to the affected LPAR partition. + + + + + R1--6. + + For the LPAR option: The check-exception RTAS call must + report global events to each LPAR partition and LPAR partition local events + only to the affected LPAR partition. + + + + + R1--7. + + For the LPAR option: The rtas-last-error RTAS call must + report only RTAS errors affecting the calling LPAR partition. + + + + + R1--8. + + For the LPAR option: The + ibm,read-pci-config RTAS calls must restrict access to + only IOAs assigned to the calling LPAR partition, and if the configuration + address is not available to the caller, must return a status of Success + with all ones as the output value. + + + + + R1--9. + + For the LPAR option: The ibm,write-pci-config RTAS + calls must restrict access to only IOAs assigned to the calling LPAR + partition, and if the configuration address is not available to the caller, + must be ignored and must return a status of Success. + + + + + R1--10. + + For the LPAR option: The ibm,write-pci-config RTAS + calls must prevent changing of the firmware assigned interrupt message + number on IOAs configured to use message signaled interrupts. + + + + + R1--11. + + For the LPAR option: The platform must virtualize the + display-character RTAS call such that the operator can distinguish and + selectively read messages from each partition without interference with + messages from other partitions. + + + + + R1--12. + + For the LPAR option: The set-indicator RTAS call must + restrict access to only indicators assigned to the calling LPAR + partition. + + + + + R1--13. + + For the LPAR option: The effects of the + system-reboot RTAS call must be restricted to only the + calling LPAR partition. + Firmware Implementation Note: One standard OS response to a machine + check is to reboot. Thus expecting the firmware to reset any error + conditions such as in the I/O sub-system. When the I/O sub-system, or parts + thereof, are shared among multiple partitions, the platform cannot allow + the boot of one partition to prevent another partition from detecting that + it was also affected by an I/O error. + + + + + R1--14. + + For the LPAR option: The platform must deliver machine + check and other event notifications to all affected partitions before + initiating recovery operations such as rebooting and resetting hardware + fault isolation circuits. + + + + + R1--15. + + For the LPAR option: The + start-cpu RTAS call must be restricted to only the + processors assigned to the calling LPAR partition. + + + + + R1--16. + + For the LPAR option: The + query-cpu-stopped-state RTAS call must be restricted to + only the processors assigned to the calling LPAR partition. + + + + + R1--17. + + For the LPAR option: The + power-off and + ibm,power-off-ups RTAS calls must deactivate the + calling partition and not power off the platform if other partitions remain + active. + + + + + R1--18. + + For the LPAR option: The + set-time-for-power-on RTAS call must activate the + platform when the partition requesting the earliest activation time is to + be activated. + + + + + R1--19. + + For the LPAR option: The + ibm,os-term RTAS call must adjust support processor + surveillance to account for the termination of the LPAR partition’s + OS. + + + + + R1--20. + + For the LPAR option: + The ibm,set-xive RTAS call must restrict access to only + interrupt sources assigned to the calling LPAR partition by silently + failing if the interrupt source is not owned by the calling partition + (return success without modifying the state of the unowed interrupt + logic). + + + + + R1--21. + + For the LPAR option: The + ibm,set-xive RTAS call must restrict the written queue + values to only interrupt processors assigned to the calling LPAR + partition. + + + + + R1--22. + + For the LPAR option: + The ibm,get-xive RTAS call must restrict access to only + interrupt sources assigned to the calling LPAR partition by silently + failing if the interrupt source is not owned by the calling partition + (return success with the least favored interrupt level, the interrupt + server number is undefined -- possibly all ones). + + + + + R1--23. + + For the LPAR option: + The ibm,int-on RTAS call must restrict access to only + interrupt sources assigned to the calling LPAR partition by silently + failing if the interrupt source is not owned by the calling partition + (return success without modifying the state of the unowed interrupt + logic). + + + + + R1--24. + + For the LPAR option: + The ibm,int-off RTAS call must restrict access to only + interrupt sources assigned to the calling LPAR partition by silently + failing if the interrupt source is not owned by the calling partition + (return success without modifying the state of the unowed interrupt + logic). + + + + + R1--25. + + For the LPAR option: The + ibm,configure-connector RTAS call must restrict access + to only Dynamic Reconfiguration Connectors assigned to the calling LPAR + partition. + + + + + R1--26. + + For the LPAR option: The platform must either define or + virtualize the power domains used by the set-power-level RTAS call such + that power level settings do not affect other partitions. + + + + + R1--27. + + For the LPAR option: The set-power-level and + get-power-level RTAS calls must restrict access to only power domains + assigned to the calling partition. + + + + + R1--28. + + For the LPAR option: The platform must restrict the + availability of the ibm,exti2c RTAS call to at most one partition (like any + IOA slot). + + + + + R1--29. + + For the LPAR option: The ibm,set-eeh-option RTAS call + must restrict access to only IOAs assigned to the calling partition. + + + + + R1--30. + + For the LPAR option: The ibm,set-slot-reset RTAS call + must restrict access to only IOAs assigned to the calling partition. + + + + + R1--31. + + For the LPAR option: The ibm,read-slot-reset-state2 + RTAS call must restrict access to only IOAs assigned to the calling + partition. + + + + + R1--32. + + For the LPAR option: The + ibm,configure-bridge RTAS call must restrict access to + only configuration addresses assigned to the calling partition. + + + + + R1--33. + + For the LPAR option: The ibm,set-eeh-option RTAS call + must restrict access to only IOAs assigned to the calling partition. + + + + + R1--34. + + For the LPAR option: The platform must restrict the + ibm,open-errinjct, ibm,close-errinjct, and ibm,errinjct RTAS calls as well + as the errinjct properties be available on at most one partition as defined + by a platform wide firmware configuration variable. + + + + + R1--35. + + For the LPAR option: Any hidden hcall()s which firmware + may use to implement RTAS functions must check its parameters to insure + compliance with all of the architecturally mandated RTAS + requirements. + + + + +
+ +
+ Shared Processor LPAR Option + The Shared Processor LPAR (SPLPAR) option allows the hypervisor to + generate multiple virtual processors by time slicing a single physical + processor. These multiple virtual processors may be assigned to one or more + OS images. There are two primary customer advantages to SPLPAR over the + standard LPAR. Most obviously, the assigned processing capacity of the + partition can scale downwards to allow for more OS images to be supported + on a single platform. The second customer advantage is that a SPLPAR + platform can achieve higher processor utilization by providing partitions, + that can use extra processing capacity, with the spare capacity ceded from + other partitions. This allows the customer to take advantage of the + variable nature of the instantaneous load on any one OS image to achieve an + increase in the average utilization of the platform’s capacity. While + the peak capacity (directly related to the platform cost) stays constant, + the customer may see a significant improvement in the average capacity + among all the platform’s workloads. However, since the peak capacity + cannot be physically exceeded, the customer may experience a wider variance + in performance when exercising the SPLPAR option. + In principal, the OS images running on the virtual processors of an + SPLPAR platform need not be aware that they are sharing their physical + processors, however, in practice, they experience significantly better + performance if they make a few optimizations. Specifically, if the OS + images cedes their virtual processor to the platform when they are idle, + and confers their processor to the holder of a spin lock for which the + virtual processor must wait. Another significant change due to SPLPAR is + that there may not be a fixed relationship between a virtual processor and + the physical processor that actualizes it. In those cases, such physical + information as location codes are undefined, affinity and associativity + values are indistinguishable, relationships to secondary caches are + meaningless, and any attempt by an OS to characterize the quality of its + processor (such as running diagnostics or performance comparisons to other + virtual processors) provide unreliable results. OF entities, that represent + physical characteristics of a virtual processor that do not remain fixed, + take on altered definitions/ requirements in an SPLPAR environment. + To provide input to the capacity planning and quality of service + tools, the hypervisor reports to an OS certain statistics, these include + the minimum processor capacity that the OS can expect (the OS may cede any + unused capacity back to the platform), the maximum processor capacity that + the platform grants to the OS, the portion of spare capacity (up to the + maximum) that the platform grants to the OS, and the maximum latency to a + dispatch via an hcall(). + The OS image optionally registers a data area (VPA) for each virtual + processor using the H_REGISTER_VPA hcall(). The hypervisor maintains a + variable, within the data area, that is incremented each time the virtual + processor is dispatched/preempted, such that the dispatch variable is + always even when the virtual processor is dispatched and always odd when it + is not dispatched. The achitectural intent for the usage of the dispatch + count variable is describe below in the paragraph devoted to conferring the + processor. Additionally this hcall() may register a trace buffer which the + OS may activate to gain detailed information about virtual processor + preemption and dispatching. + Both the VPA and the trace log buffer contain statistics on how long + the virtual processor has waited (not been dispatched on a physical + processor). Architecturally, the virtual processor wait time is divided + into three intervals: + + + + The time that the virtual processor waited to become logically + ready to run again, for example: + + + + The time needed to resolve a fault + + + + The time needed to process a hypervisor preemption + + + + The time until a wake up event after voluntarily relinquishing the + physical processor + + + + + + The time spent waiting after interval 1 until virtual processor + capacity was available. Shared processor partitions are granted a quantum + of virtual processor capacity (execution time) each dispatch wheel + rotation; thus if the partition has used its capacity, the ready to run + virtual processor has to wait until the next quantum is granted. + + + + The time spent waiting after interval 2 until the virtual + processor was dispatched on a physical processor. This is arises from the + fact that multiple ready to run virtual processors with virtual processor + capacity may be competing for a single physical processor. + + + + Two other performance statistics are available via hcall()s these are + the Processor Utilization Register, and Pool Idle Count returned by the + H_PURR and H_PIC hcall()s respectively. These two statistics are counts in + the same units as counted by the processor time base. Like the time base, + the PUR and PIC are 64 bit values that are set to a numerically low value + during system initialization. The difference between their values at the + end and beginning of monitored operations provides data on virtual + processor performance. The value of the PUR is a count of processor cycles + used by the calling virtual processor. The PUR count is intended to provide + an indication to the partition software of the computation load supported + by the virtual processor. SPLPAR virtual processors are created by + dispatching the virtual processor’s architectural state on one of the + physical processors from a pool of physical processors. The value of the + PIC is the summation of the physical processor pool idle cycles, that is + the number of time base counts when the pool could not dispatch a virtual + processor. The PIC count is intended to provide an indication to platform + management software of the pool capacity to perform more work. + A well behaved OS image normally cedes its virtual processor to the + platform using the H_CEDE hcall() after it determines that it currently has + run out of useful work. The H_CEDE hcall() gives up the virtual processor + until either an external interrupt (including decrementer, and Inter + Processor Interrupt) or another one of the partition’s processors + executes an H_PROD hcall() see below. Note the decrementer appears to + continue to run during the time that the virtual processor is ceded to the + platform. The H_CEDE hcall() always returns to the next instruction, + however, prior to executing the next instruction, any pending interrupt is + taken. To simulate atomic testing for work, the H_CEDE call may be called + with interrupts disabled, however, the H_CEDE call activates the virtual + processor’s MSREE bit to avoid going into a wait state with interrupts + masked. + A multi-processor OS uses two methods to initiate work on one + processor from another, in both cases the requesting processor places a + unit of work structure on a queue, and then either signals the serving + processor via an Inter-Processor interrupt to service the work queue, or + waits until the serving processor polls the work queue. The former method + translates directly to the SPLPAR environment, the second method may + experience significant performance degradation if the serving processor has + ceded. To provide a solution to this performance problem, the SPLPAR + provides the H_PROD hcall(). The H_PROD hcall() takes as a parameter the + virtual processor number of the serving processor. Waking a potentially + ceded or ceding processor is subject to many race conditions. The semantic + of the H_PROD hcall() attempts to minimize these race conditions. First the + H_CEDE and H_PROD hcall()s serialize on each other per target virtual + processor. Secondly by having the H_PROD firmware set a per virtual + processor memory bit before attempting to determine if the target virtual + processor is preempted. If the processor is not preempted the H_PROD + hcall() immediately returns, else the processor is dispatched and the + memory bit is reset. If the processor was dispatched, and subsequently the + virtual processor does a H_CEDE operation, the H_CEDE hcall() checks the + virtual processor’s memory bit and if set, resets the bit and returns + immediately (not ceding the physical processor to another virtual + processor). An OS might choose to always do an H_PROD after an enqueue to a + polled queue or it might qualify making the H_PROD hcall() with a status + bit set by the by the target processor when it decides to cede its virtual + processor. + Locking in a SPLPAR environment presents a problem for + multi-programming OSs, in that the virtual processor that is holding a lock + may have been preempted. In that case, spinning, waiting for the lock, + simply wastes time since the lock holder is in no position to release the + lock -- it needs processor cycles and cannot get them for some period of + time and the spinner is using up processor cycles waiting for the lock. The + condition is known as a live lock, however, it eventually resolves itself. + The SPLPAR optimization to alleviate this problem is to have the waiting + virtual processor “confer” its processor cycles to the lock + holder’s virtual processor until the lock holder has had a chance to + run another dispatch time slice. + As with the cede/prod pair of functions above, the confer function is + subject to timing window races between the waiting process determining that + the lock holder has been preempted and execution of the H_CONFER hcall() + during which time the originally holding virtual processor may have been + dispatched, released the lock and ceded the processor. To manage this + situation, the H_CONFER takes two parameters, one that specifies the + virtual processor(s) that are to receive the cycles and the second + parameter (valid only when a single processor is specified) which + represents the dispatch count of the holding virtual processor atomically + captured when the waiting processor decided to confer its cycles to the + waiting processor. + The semantic of H_CONFER checks the processor parameter for validity, + then if it is the “all processors” code proceeds to the + description below. If the processor parameter refers to a valid virtual + processor owned by the calling virtual processor’s partition, that is + not dispatched, that has not conferred its cycles to all other processors, + and who’s current dispatch count matches that of the second + parameter, the time remaining from the calling processors time slice is + conferred to the specified virtual processor. + If the first parameter of H_CONFER specifies the “all + processors” code, then it marks the calling virtual processor to + confer all its cycles until all of the partition’s virtual + processors, that have not ceded or conferred their cycles, have had a + chance to run a dispatch time slice. The “all processors” + version may be viewed as having the hypervisor record the dispatch counts + for all the other platform processors in the calling virtual + processor’s hypervisor owned “confer structure”, then + prior to any subsequent dispatch of the calling processor, if the confer + structure is not clear, the hypervisor does the equivalent of removing one + entry from the confer structure and calling H_CONFER for the specific + virtual processor. If the specific virtual processor confer is rejected + (because the virtual processor is running, ceded, conferred, or the + dispatch count does not match) then the next entry is tried until the + confer structure is clear before the originally calling virtual processor + is re-dispatched. + Virtual processors may migrate among the physical processor pool from + one dispatch cycle to the next. OF device tree properties that relate the + characteristics of the specific physical processor such as location codes, + and other vital product data cannot be consistent and are not reported in + the nodes of type + cpu if the partition is running in SPLPAR mode. Most + processor characteristics properties such as time base increment rate, are + consistent for all processors in the system physical and virtual so are + still reported via their standard properties. Additionally nodes of type + + L2 are not present in the tree since they are shared + with other virtual processors making optimizations based upon their + characteristics impossible. The Processor Identification Register (PIR) + should not be accessed by the OS since from cycle to cycle the OS may get + different readings, instead the virtual processor number (the number from + the + “ibm,ppc-interrupt-server#s” property, + contained in the nodes of type + cpu, associated with this virtual processor) is used + as the processor number to be passed as parameters to RTAS and hcall() + routines for managing interrupts etc. + + Software Note: When the client program (OS) first gets + control during the boot sequence, the virtual processor number of the + single processor that is operational is identified by the + /chosen node of the device tree. The + cpu nodes list the other virtual processors that the + first processor may start. These are started one at a time, giving the + virtual processor number as an input parameter to the call. As each + processor starts, it starts executing a program that picks up its virtual + processor number from a memory structure initialized by the processor that + called the start-cpu function. The newly started processor then records the + location of its per processor memory structure (where it saves its virtual + processor number) in one of the SPRG registers. + +
+ Virtual Processor Areas + The per processor areas are registered with the H_REGISTER_VPA + hcall() that takes three parameters. The first parameter is a flags field + that specifies the specific sub function to be performed, the second is + the virtual processor number of one of the processors owned by the + calling virtual processor’s partition for whom the area is being + registered. The third parameter is the logical address, within the + calling virtual processor’s partition, of the contiguous logically + addressed storage area to be registered. Registered areas are aligned on + a cache line (l1) size boundary and may not span an LMB boundary and for + the CMO option may not span an entitlement granule boundary. The length + of the area is provided to the hcall() in starting in byte offset 4 of + the area being registered. The H_REGISTER _VPA hcall() registers various + types of areas, and after verifying the parameters, initializes the + structure’s variables. + Per Virtual Processor Area: This area contains shared processor + operating parameters as defined in + . A shared processor LPAR aware + OS registers this area early in its initialization. The other types of + virtual processor areas can only be registered after the Per Virtual + Processor Area has been successfully registered. The minimum length of + the Per Virtual Processor Area is 640 bytes and the structure may not + span a 4096 byte boundary. + Dispatch Trace Log Buffer: This area is optionally registered by + OS’s that desire to collect performance measurement data relative + to its shared processor dispatching. The minimum size of this area is 48 + bytes while the maximum is 4 GB. See + for more details + SLB Shadow Buffer: This area is optionally registered by OS’s + that support the SLB-shadow function set. The structure may not span a + 4096 byte boundary. This function set allows the hypervisor to + significantly reduce the overhead associated with virtual processor + dispatch in a shared processor LPAR environment, and to provide enhanced + recovery from SLB hardware errors. See + for more details. + + Software Note: Registering, deregistering or changing + the value of a variable in one of the Virtual Processor Areas for a + different virtual processor (i.e. changing a value in the VPA of + processor A from processor B) may be problematic. In no cases is + partition integrity be compromised, but results may be imprecise if such + a change is made during the virtual processor preempt/dispatch window. If + the owning processor is started, registration or deregistration should + only be done by the owning processor, if the processor is stopped, + registration or deregistration can safely be done by other processors. + Also, for example, changing the number of persistent SLB Shadow Buffer + entries cause uncertainty in the number of currently valid SLB entries in + that virtual processor. In some cases, such as turning on and off + dispatch tracing, such uncertainty may be acceptable. + +
+ Per Virtual Processor Area +   + + Per Virtual Processor Area + + + + + + + + + Byte Offset + + + + + Length in Bytes + + + + + Variable Description + + + + + + + + 0x00 + + + 4 + + + Descriptor: This field is supplied for OS identification + use, it may be set to any value that may be useful (such as a + pattern that may be identified in a dump) or it may be left + uninitalized. + Historic values include: 0xD397D781 + + + + + 0x04 + + + 2 (unsigned) + + + Size: The size of the registered structure (640) + + + + + 0x6 - 0x17 + + + 18 + + + Reserved for Firmware Use + + + + + 0x18 - 0x1B + + + 4 + + + Physical Processor FRU ID + + + + + 0x1C - 0x1F + + + 4 + + + Physical Processor on FRU ID + + + + + 0x20 - 0x57 + + + 56 + + + Reserved for Firmware Use + + + + + 0x58 - 0x5F + + + 8 + + + Virtual processor home node associativity changes + counters (changes in the 8 most important associativity + levels) + + + + + 0x60 - 0xAF + + + 80 + + + Reserved for Firmware Use + + + + + 0xB0 + + + 1 + + + Cede Latency Specifier + + + + + 0xB1 + + + 7 + + + Reserved For LoPAR Expansion + + + + + 0xB8 + + + 1 + + + Dispatch Trace Log Enable Mask: (Note this entry is valid + only if a Dispatch Trace Log Buffer has been registered). A + Trace Log Entry is created when the virtual processor is + dispatched following its preemption for an enabled + cause. + =0 no dispatch trace logging + Bit 7 =1 Trace voluntary (OS initiated) virtual processor + waits + Bit 6 =1 Trace time slice preempts + Bit 5 = 1 Trace virtual partition memory page + faults. + All other values are reserved + + + + + 0xB9 + + + 1 + + + Bits 0-6 Reserved + Bit 7 = 0 -- Dedicated processor cycle donation + disabled + Bit 7 = 1 -- Dedicated processor cycle donation + enabled. + + + + + 0xBA + + + 1 + + + Maintain FPRs: + =0 architected state of floating point registers may be + discarded at any time, + =1 architected state of floating point registers must be + maintained, + all other values are reserved + Note: When set in conjunction with offset 0xFF the 128 + bit VSX space is saved on processors supporting the VSX option + ( 2.06 and + beyond). + + + + + 0xBB + + + 1 + + + Maintain PMCs: + =0 architected state of performance monitor counters may + be discarded at any time, + =1 architected state of performance monitor counters must + be maintained, + all other values are reserved + + + + + 0xBC-0xD7 + + + 28 + + + Reserved For Firmware Use + + + + + 0xD8-0xDF + + + 8 + + + Any non-zero value is taken by the firmware to be the OS, + estimate, in PURR units, of the cumulative number of cycles + that it has consumed on this virtual processor, while idle, + since it was initialized. + + + + + 0xE0 - 0xFB + + + 28 + + + Reserved for Firmware Use + + + + + 0xFC + + + 2 (unsigned) + + + Maintain #SLBs: + This number of Segment Lookaside Buffer Registers (up to + the platform implementation maximum) are maintained, all others + (up to the platform implementing maximum) may be discarded at + any time. + The value 0xFFFF maintains all SLBs + + + + + 0xFE + + + 1 + + + Idle: + =0 The OS is busy on this processor + =1 The OS is idle on this processor + All other values are reserved + + + + + 0xFF + + + 1 + + + Maintain VMX state: + =0 architected state of the processor’s VMX + facility, may be discarded at any time + =1 architected state of the processor’s VMX + facility, must be maintained + All other values are reserved + Note: When set in conjunction with offset 0xBA the 128 + bit VSX space is saved on processors + supporting the VSX option ( + 2.06 and beyond). + + + + + 0x100 + + + 4 (unsigned) + + + Virtual Processor Dispatch Counter: + (Even when virtual processor is dispatched odd when it is + preempted/ceded/conferred) + + + + + 0x104 + + + 4 (unsigned) + + + Virtual Processor Dispatch Dispersion Accumulator: + Incremented on each virtual processor dispatch if the + physical processor differs from that of the last + dispatch. + + + + + 0x108 + + + 8 (unsigned) + + + Virtual Processor Virtual Partition Memory Fault Counter: + Incremented on each Virtual Partition Memory page fault. + + + + + 0x110 + + + 8 (unsigned) + + + Virtual Processor Virtual Partition Memory Fault Time + Accumulator: Time, in Time Base units, that the virtual + processor has been blocked waiting for the resolution of + virtual Partition Memory page faults. + + + + + 0x118 - 0x11F + + + 8 + + + Unsigned accumulation of PURR cycles expropriated by the + hypervisor when VPA byte offset 0xFE = 1 + + + + + 0x120 - 0x127 + + + 8 + + + Unsigned accumulation of SPURR cycles expropriated by the + hypervisor when VPA byte offset 0xFE = 1 + + + + + 0x128 - 0x12F + + + 8 + + + Unsigned accumulation of PURR cycles expropriated by the + hypervisor when VPA byte offset 0xFE = 0 + + + + + 0x130 - 0x137 + + + 8 + + + Unsigned accumulation of SPURR cycles expropriated by the + hypervisor when VPA byte offset 0xFE = 0 + + + + + 0x138 - 0x13F + + + 8 + + + Unsigned accumulation of PURR cycles donated to the + processor pool when VPA byte offset 0xFE = 1 + + + + + 0x140 - 0x147 + + + 8 + + + Unsigned accumulation of SPURR cycles donated to the + processor pool when VPA byte offset 0xFE = 1 + + + + + 0x148 - 0x14F + + + 8 + + + Unsigned accumulation of PURR cycles donated to the + processor pool when VPA byte offset 0xFE = 0 + + + + + 0x150 - 0x157 + + + 8 + + + Unsigned accumulation of SPURR cycles donated to the + processor pool when VPA byte offset 0xFE = 0 + + + + + 0x158-0x15F + + + 8 + + + Accumulated virtual processor wait interval 3 timebase + cycles. (waiting for physical processor availability) + + + + + 0x160 - 0x167 + + + 8 + + + Accumulated virtual processor wait interval 2 timebase + cycles. (waiting for virtual processor capacity) + + + + + 0x168 - 0x16F + + + 8 + + + Accumulated virtual processor wait interval 1 timebase + cycles. (waiting for virtual processor ready to run) + + + + + 0x170 - 0x177 + + + 8 + + + Reserved for Firmware Use + + + + + 0x178 - 0x17F + + + 8 + + + Reserved for Firmware Use + + + + + 0x180 - 0x183 + + + 4 + + + For the CMO option: The OS may report in this field as a + hint to the hypervisor the accumulated number, since the + virtual processor was started, of ‘page in’ + operations initiated for pages that were previously swapped + out.” + + + + + 0x184 - 0x187 + + + 4 + + + Reserved for Firmware Use + + + + + 0x188 - 0x18F + + + 8 + + + Reserved for Firmware Use + + + + + 0x190 - 0x197 + + + 8 + + + .Reserved for Firmware Use + + + + + 0x198 - 0x217 + + + 128 + + + Reserved for Firmware Use + + + + + 0x218 - 0x21F + + + 8 + + + Dispatch Trace Log buffer index counter. + + + + + 0x220 - 0x27F + + + 96 + + + Reserved for Firmware Use + + + + +
+ + + + R1--1. + + For the SPLPAR option: If the OS registers a Per + Virtual Processor Area, it must correspond to the format specified in + . + + + + +
+ +
+ Dispatch Trace Log Buffer + The optional virtual processor dispatch trace log buffer is a + circularly managed buffer containing individual 48 byte entries, with the + first entry starting at byte offset 0. Therefore, the 4 byte registration + size field is overwritten by the first Trace Log Buffer entry. (Note the + hypervisor rounds down the dispatch trace log buffer length to a multiple + of 48 bytes and wraps when reaching that boundary.) A vpa location + contains the index counter that + the hypervisor increments each time that it makes a dispatch trace log + entry such that it always indicates the next entry to be filled. The low + order bits (modulo the buffer length divided by 48) of the counter + provide the index of the next entry to be filled, therefore, the buffer + wraps each (buffer length divided by 48 entries), while the high order + counter bits indicate how many buffer wraps have occurred. Prior to + enabling dispatch trace logging, the OS should initialize the vpa index + counter to the value of 0. The format of dispatch trace log buffer + entries is given in + . + The architectural intent is that OS trace tools keep a shadow index + counter into the log buffer of the next entry to be filled by the + hypervisor. Prior to making an entry of their own, such tools compare + their index counters with that of the hypervisor from the vpa, if they + are equal, no preempts/dispatches have occurred since the last OS trace + hook. If the two index counters are not equal, then the OS trace tool + processes the intermediate time stamps into the OS’s trace log, + updating its dispatch trace log buffer index until all have been + processed, then the new trace entry is added to the OS’s trace log. + Note, because of races, the processor may be preempted just prior to the + OS trace tool adding the new trace log entry, to handle this case, the OS + trace tool can examine the dispatch trace log buffer index immediately + after the adding of the new trace log entry and if needed adjust its own + trace log. In the extremely unlikely event that the two counters are off + by trace buffer length divided by forty eight or more counts, the OS + trace tool can detect that a dispatch trace log buffer overflow has + occurred, and trace data has been lost. + + + Dispatch Trace Log Buffer Entry + + + + + + + + + Byte Offset + + + + + Length in Bytes + + + + + Variable Description + + + + + + + + 0x0 + + + 1 + + + Reason Code for the virtual processor dispatch: + 0: The virtual processor was dispatched at the external + interrupt vector location to handle an IOA interrupt, Virtual + interrupt, or interprocessor interrupt. + 1: The virtual processor was dispatched to handle + firmware internal events. + 2: The virtual processor was dispatched at the next + sequential instruction due to an H_PROD call by another + partition processor. + 3: The virtual processor was dispatched at the DECR + interrupt vector due to a decrementer interrupt. + 4: The processor was dispatched at location specified in + load module (boot) or at the system reset interrupt vector. + (virtual yellow button). + 5: The virtual processor was dispatched to handle + firmware internal events + 6: The virtual processor was dispatched at the next + sequential instruction to use cycles conferred from another + partition processor + 7: The virtual processor was dispatched at the next + sequential instruction for its entitled time slice. + 8: The virtual processor was dispatched at the faulting + instruction following a virtual partition memory page + fault. + + + + + 0x1 + + + 1 + + + Reason Code for virtual processor preemption: + 0: Not used (for compatibility with earlier versions of + the facility) + 1: Firmware internal event + 2: Virtual processor called H_CEDE + 3: Virtual processor called H_CONFER + 4: Virtual processor reached the end of its timeslice + (HDEC) + 5: Partition Migration/Hibernation page fault + 6: Virtual memory page fault + + + + + 0x2 - 0x3 + + + 2 + + + Processor index of the physical processor actualizing the + thread on this dispatch. + + + + + 0x4 - 0x7 + + + 4 + + + Time Base Delta between enqueued to dispatcher and actual + dispatch on a physical processor + + + + + 0x8 - 0xB + + + 4 + + + Time Base Delta between ready to run and enqueue to + dispatcher + + + + + 0xC - 0xF + + + 4 + + + Time Base Delta between waiting and ready to run + (preempt/fault resolution time) + + + + + 0x10 - 0x17 + + + 8 + + + Time Base Value at the time of dispatch/wait + + + + + 0x18 - 0x1F + + + 8 + + + For virtual processor preemption reason codes 5 & 6: + Logical real address of faulting page; else reserved. + + + + + 0x20 - 0x27 + + + 8 + + + SRR0: At the time of preempt/wait + + + + + 0x28 - 0x2F + + + 8 + + + SRR1: At the time of preempt/wait + + + + +
+ + + + R1--1. + + For the SPLPAR option: If the OS registers a Dispatch + Trace Log Buffer, it must correspond to the format specified in + . + + + + +
+ +
+ SLB Shadow Buffer + On platforms supporting the SLB-Buffer function set, the OS may + optionally register an SLB shadow buffer area. When the OS takes this + option, it allows the hypervisor to optimize the saving of SLB entries, + thus reducing overhead and providing more processor capacity for the OS, + and also allows the platform to recover from certain SLB hardware faults. + When the OS registers an SLB shadow buffer for its virtual processor, the + processor’s SLB is architecturally divided into three categories + relative to their durability as depicted in + . +
+ Processor SLB relationship to the OS registered VPA and SLB Shadow Buffer + + + + + + + + +
+ OS may dynamically change M and N (for (N+1)*16 <= Length of SLB Shadow Buffer) + Each category of SLB entries consists of 0-n contiguous + SLBs. + Persistent Entries: The first N (starting at SLB index 0, N + specified by the numeric content of the first 4 bytes of the registered + SLB Shadow Buffer) SLBs are maintained persistent across all virtual + processor dispatches unless an unrecovered SLB error is noted. OS + maintains a shadow copy of those SLB entries in the registered SLB shadow + buffer. The OS sizes its SLB Shadow buffer for the largest number of + persistent entries it can ever maintain. If the OS registers an SLB + Shadow buffer, the hypervisor does not save the contents of the + Persistent entries on virtual processor preempt, cede, or confer. The OS + should minimally record as persistent the entries it needs to handle its + SLB fault interrupts to fill in required Volatile (and potentially) + Transient entries. + Volatile Entries: The next M-N SLBs (beginning at the next higher + SLB index after the last Persistent entry up through the entry specified + by the “maintain#SLBs” parameter of the VPA) may disappear. + The OS needs to be prepared to recover these entries via SLB fault + interrupts. For performance optimization, the hypervisor normally + maintains the state of these entries across H_DECR interrupts and most + hcalls(), they may be lost on H_CEDE calls. + Transient Entries: The platform makes no attempt to maintain the + state of these entries and they may be lost at any time. + The OS may dynamically change the number of Persistent entries by + atomically changing the value of the 4 byte parameter at SLB Shadow + Buffer offset 0. + The hypervisor does not explicitly check the value of this + parameter, however, the hypervisor limits the number of SLBs that it + attempts to load from the shadow buffer to the lesser of the maximum + number of SLB entries implemented by the platform, or the maximum number + of entries containable in the SLB Shadow buffer length when it was + registered. + + + + R1--1. + + For the SPLPAR option: If the OS + registers an SLB Shadow Buffer, it must correspond to the format + specified in + . + + + + +
+
+ +
+ Shared Processor LPAR OF Extensions + + +
+ Shared Processor LPAR Function Sets in + <emphasis role="bold"><literal>“ibm,hypertas-functions”</literal></emphasis> + + + + hcall-splpar + + + + hcall-pic + + + + SLB-Buffer + + +
+ +
+ Device Tree Variances + If an SPLPAR implementation does not maintain a fixed relationship + between the virtual processor that it reports to the OS image in the OF + device tree properties and the physical processor that it uses to + actualize the virtual processor, then OF entities that imply a fixed + physical relationship are not reported. These may include those listed in + + . + + + OF Variances due to SPLPAR + + + + + + + + Entity + + + + + Variance to standard + definition + + + + + + + + + “ibm,loc-code” property + + + If the physical relationship between virtual processors + and physical processors is not constant this property is + omitted from the virtual processor’s node. If missing, + the OS should not run diagnostics on the virtual + processor + + + + + + “l2-cache” property + + + If the physical relationship between virtual processors + and physical processors is not constant the secondary cache + characteristics are not relevant and this property is omitted + from the virtual processor’s node. + + + + + Nodes named + l2-cache + + + If the physical relationship between virtual processors + and physical processors is not constant the secondary cache + characteristics are not relevant and this node is omitted from + the partition’s device tree. + + + + + + “ibm,associativity” property + + + If the physical relationship between virtual processors + and physical processors is not constant the + “ibm,associativity” property reflects + the same domain for all virtual processors actualized by a + given physical processor pool. Note, even though the + associativity of virtual processors may be indistinguishable, + the associativity among other platform resources may be + relevant. + + + + +
+ + + + R1--1. + + For the SPLPAR option: If the platform does not + maintain a fixed relationship between its virtual processors and the + physical processors that actualize them, then the platform must vary the + device tree elements as outlined in + . + + + + +
+
+ +
+ Shared Processor LPAR Hypervisor Extensions + + +
+ Virtual Processor Preempt/Dispatch + A new virtual processor is dispatched on a physical processor when + one of the following conditions happens: + + + + The physical processor is idle and a virtual processor was made + ready to run (interrupt or prod) + + + + The old virtual processor exhausted its time slice (HDECR + interrupt). + + + + The old virtual processor ceded/conferred its cycles. + + + + When one of the above conditions occurs, the hypervisor, by + default, records all the virtual processor architected state including + the Time Base and Decrementer values and sets the hypervisor timer + services to wake the virtual processor per the setting of the + decrementer. The virtual processor’s Processor Utilization Register + value for this dispatch is computed. The VPA’s dispatch count is + incremented (such that the result is odd). Then the hypervisor selects a + new virtual processor to dispatch on the physical processor using an + implementation dependent algorithm having the following characteristics + given in priority order: + + + + The virtual processor is “ready to run” (has not + ceded/conferred its cycles or exhausted its time slice). + + + + Ready to run virtual processors are dispatched prior to waiting + in excess of their maximum specified latency. + + + + Of the non-latency critical virtual processors ready to run, + select the virtual processor that is most likely to have its working set + in the physical processor’s cache or for other reasons runs most + efficiently on the physical processor. + + + + If no virtual processor is “ready to run” at this time, + start accumulating the Pool Idle Count (PIC) of the total number of idle + processor cycles in the physical processor pool. + Optionally, flags in the VPA may be set by the OS to indicate to + the hypervisor that selected architected state of the virtual processor + need not be maintained (that is, the contents of these architected + facilities may be lost at any time without notice). The hypervisor may + then optimize its preempt/dispatch routines accordingly. Refer to + and SLB Shadow Buffer + description for the definition of these flags and values. The hypervisor + modifies any such OS setable and readable processor state that is not + explicitly saved and restored on a virtual processor dispatch so as to + prevent a covert channel between partitions. + When the virtual processor is dispatched, the virtual + processor’s “prod” bit is reset, the saved architected + state of the virtual processor is restored from that saved when the + virtual processor was preempted, ceded, or conferred, except for the time + base which retains the current value of the physical processor and the + decrementer which is reduced from the state saved value per current Time + Base value minus saved Time Base value. The hypervisor sets up for + computing the PUR value increment for the dispatch. + At this time, the hypervisor increments the virtual + processor’s VPA dispatch count (such that the value is even). The + hypervisor checks the VPA’s dispatch log flag, if set, the + hypervisor creates a pair of log entries in the dispatch log and stores + the circular buffer index in the first buffer entry. + If the virtual processor was signaled with an interrupt condition + and the physical interrupt has been reset, then the hypervisor adjusts + the virtual processor architected state to reflects that of a physical + processor taking the same interrupt prior to executing the next + sequential instruction and execution starts with the first instruction in + the appropriate interrupt vector. If no interrupt has been signaled to + the virtual processor or the physical interrupt is still active, then + execution starts at the next sequential instruction following the + instruction as noted by the hypervisor when the virtual processor ceded, + conferred, or was preempted. + The Platform allocates processor capacity to a partition’s + virtual processors using the architectural metaphor of a “dispatch + wheel” with a fixed implementation dependent rotation period. Each + virtual processor receives a time slice each rotation of the dispatch + wheel. The length of the time slice is determined by a number of + parameters, the OS image has direct control, within constraints, over + three of these parameters (number of virtual processors, Entitled + Processor Capacity Percentage, Variable Processor Capacity Weight). The + constraints are determined by partition and partition aggregate + configurations that are outside the scope of this architecture. For + reference, partition definitions provide the initial settings of these + parameters while the aggregation configurations provide the constraints + (including the degenerate case where an aggregation encapsulates only a + single member LPAR). + Entitled Processor Capacity Percentage: The percentage of a + physical processor that the hypervisor guarantees to be available to the + partition’s virtual processors (distributed in a uniform manner + among the partition’s virtual processors -- thus the number of + virtual processors affects the time slice size) each dispatch cycle. + Capacity ceded or conferred from one partition virtual processor extends + the time slices offered to other partition processors. Capacity ceded or + conferred after all of the partition’s virtual processors have been + dispatch is added to the variable capacity kitty. The initial, minimum + and maximum constraint values of this parameter are determined by the + partition configuration definition. The H_SET_PPP hcall() allows the OS + image to set this parameter within the constraints imposed by the + partition configuration definition minimum and maximums plus constraints + imposed by partition aggregation. + Variable Processor Capacity Weight: The unitless factor that the + hypervisor uses to assign processor capacity in addition to the Entitled + Processor Capacity Percentage. This factor may take the values 0 to 255. + A virtual processor’s time slice may be extended to allow it to use + capacity unused by other partitions, or not needed to meet the Entitled + Processor Capacity Percentage of the active partitions. A partition is + offered a portion of this variable capacity kitty equal to: (Variable + Processor Capacity Weight for the partition) / (summation of Variable + Processor Capacity Weights for all competing partitions). The initial + value of this parameter is determined by the partition configuration + definition. The H_SET_PPP hcall() allows the OS image to set this + parameter within the constraints imposed by the partition configuration + definition maximum. Certain partition definitions may not allow any + variable processor capacity allocation. + Unallocated Processor Capacity Percentage: The amount of processor + capacity that is currently available within the constraints of the LPAR's + current environment for allocation to Entitled Processor Capacity + Percentage. Race conditions may change the current environment before a + request for this capacity can be performed, resulting in a constrained + return from such a request. + Unallocated Variable Processor Capacity Weight: The amount of + variable processor capacity weight that is currently available within the + constraints of the LPAR's current environment for allocation to the + partition's variable processor capacity weight. Race conditions may + change the current environment before a request for this capacity can be + performed, resulting in a constrained return from such a request. + System Parameters readable via the + ibm,get-system-parameter RTAS call (see + ) + communicate a variety of configuration and + constraint parameters among which are determined by the partition + definition. + By means that are beyond the scope of this architecture, various + partitions may be organized into aggregations, for example “LPAR + groups”, for the purposes of load balancing. These aggregations may + impose constraints such as: “The summation of the minimum available + capacity for all virtual processors supported by the LPAR group cannot + exceed 100% of the group’s configured capacity”. + + + + R1--1. + + For the SPLPAR option: + The platform must dispatch each partition virtual processors each dispatch cycle unless + prevented by the semantics of the H_CONFER hcall(). + + + + + R1--2. + + For the SPLPAR option: + The summation of the processing capacity that the platform dispatches to the virtual + processors of each partition must be at least equal to that partition's + Entitled Processor Capacity Percentage unless prevented by the semantics + of the H_CONFER and H_CEDE hcall()s. + + + + + R1--3. + + For the SPLPAR option: + The processing capacity that the platform dispatches to each of the partition's virtual + processors must be substantially equal unless prevented by the semantics + of the H_CONFER and H_CEDE hcall()s. + + + + + R1--4. + + For the SPLPAR option: The platform must distribute + processor capacity allocated to SPLPAR virtual processor actualization + not consumed due to Requirements + , + , and + to partitions in strict + accordance with the definition of Variable Processor Capacity Weight + unless prevented by the LPAR's definition (capped) or the semantics of + the H_CONFER and H_CEDE hcall()s. + Note: A value of 0 for a Variable Processor Capacity Weight + effectively caps the partition at its Entitled Processor Capacity + Percentage value. + + + + + R1--5. + + For the SPLPAR option on platforms: The platform must + increment the counters in VPA offsets 0x158-0x16F per their definitions + in + . + + + + + R1--6. + + For the SPLPAR option on platforms : To maintain + compatibility across partition migration and firmware version levels the + OS must be prepared for platform implementations that do not increment + VPA offsets 0x158 - 0x16F. + + + + +
+ +
+ H_REGISTER_VPA + Register Virtual Processor Areas (these include the parameter area + known as the VPA, the Dispatch Trace Log Buffer, and if the SLB-Buffer + function set is supported, the SLB Shadow Buffer). Note if the caller + makes multiple registration requests for a given per virtual processor + area for a given virtual processor, the last registration wins, and if + the same memory area is registered for multiple processors, the area + contents are unpredictable, however, LPAR isolation is not + compromised. + The syntax of the H_REGISTER_VPA hcall() is given below. + + + + + Semantics: + + + + wVerify that the flags parameter is a supported value else return + H_Parameter. (That the subfunction field (Bits 16-23) is one of the + values supported by this call. Optionally that all other bits are zero. + Callers should not set any bits other than those specifically defined, + however, implementations are not required to check the value of bits + outside of the subfunction field.) + + + + Verify that the proc-no parameter references a virtual processor + owned by the calling virtual processor’s partition else return + H_Parameter + + + + If the sub function is a register, verify that the addr parameter + is an L1 cache line aligned logical address within the memory owned by + the calling virtual processor’s partition else return + H_Parameter. + + + + If the Shared Logical Resource option is implemented and the addr + parameter represents a shared logical resource location that has been + rescinded by the owner, return H_RESCINDED. + + + + + + Case on subfunction in flags parameter: + + + + Register VPA: + + + + Verify that the size field (2 bytes) at offset 0x4 is at least + 640 bytes else return H_Parameter. + + + + Verify that the entire structure (per the size field and vpa) + does not span a 4096 byte boundary else return H_Parameter. + + + + Record the specified processor’s vpa logical address for + access by other SPLPAR hypervisor functions. + + + + Initialize the contents of the area per + . + + + + Return H_Succes + + + + + + Register Dispatch Trace Log Buffer: + + + + Verify that the size field (4 bytes) at offset 0x4 is at least 48 + bytes else return H_Parameter. + + + + For the CMO option, verify that the entire structure (per the + size field and vpa parameter) does not span a memory entitlement granule + boundary else return H_MLENGTH_PARM. + + + + Verify that a VPA has been registered for the specified virtual + processor else return H_RESOURCE. + + + + Initialize the specified processor’s preempt/dispatch trace + log buffer pointers and index. + + + + Return H_Success. + + + + + + Register SLB Shadow Buffer (if SLB-Buffer function set is + supported): + + + + Verify that the size field (4 bytes) at offset 0x4 is at least 8 + bytes and that the entire structure (per the size and vpa parameters) + does not span a 4096 byte boundary else return H_Parameter. + + + + Verify that a VPA has been registered for the specified virtual + processor else return H_RESOURCE. + + + + Initialize the specified processor’s SLB Shadow buffer + pointers and set the maximum persistent SLB restore index to the lesser + of the maximum number of processor SLBs or the maximum number of entries + in the registered SLB Shadow buffer. + + + + Return H_Success. + + + + + + Deregister VPA: + + + + Verify that a Dispatch Trace Log buffer is not registered for the + specified processor else return H_RESOURCE. + + + + Verify that an SLB Shadow buffer is not registered for the + specified processor else return H_RESOURCE. + + + + Clear any partition memory pointer to the specified + processor’s VPA (note no check is made that a valid VPA + registration exists). + + + + Return H_Success. + + + + + + Deregister Dispatch Trace Log Buffer: + + + + Clear any partition memory and/ or hypervisor pointer to the + specified processor’s Dispatch Trace Buffer (note no check is made + that a valid Dispatch Trace Buffer registration exists). + + + + Return H_Success. + + + + + + Deregister SLB Shadow Buffer (if SLB-Buffer function set is + supported): + + + + Clear any hypervisor pointer(s) to the specified + processor’s SLB Shadow buffer (note no check is made that a valid + SLB Shadow buffer registration exists). + + + + Zero the hypervisor’s maximum persistent SLB restore index + for the specified processor. + + + + Return H_Success. + + + + + + Else Return H_Function. + + + + + + R1--1. + + For the SPLPAR option: The platform must implement + the H_REGISTER_PVA hcall() following the syntax and semantics of + . + + + + + R1--2. + + For the SLPAR plus SLB Shadow Buffer options: The + platform must register, and deregister the optional SLB Shadow buffer per + the syntax and semantics of + . + + + + + R1--3. + + For the SLPAR plus SLB Shadow Buffer options: The + platform must make persistent the SLB entries recorded by the OS within + the SLB Shadow buffer as described in + . + + + + + +
+ +
+ H_CEDE + The architectural intent of this hcall() is to have the virtual + processor, which has no useful work to do, enter a wait state ceding its + processor capacity to other virtual processors until some useful work + appears, signaled either through an interrupt or a prod hcall(). To help + the caller reduce race conditions, this call may be made with interrupts + disabled but the semantics of the hcall() enable the virtual + processor’s interrupts so that it may always receive wake up + interrupt signals. As a hint to the hypervisor, the cede latency + specifier + indicates how long the OS can + tolerate the latency to an H_PROD hcall() or interrupt, this may affect + how the hypervisor chooses to use or even power down the actualizing + physical processor in the mean time. + + Software Note: The floating point registers may not + be preserved by this call if the “Maintain FPRs” field of the + VPA =0, see + . + + + Syntax: + + + + + + + Semantics: + + + + Enable the virtual processor’s MSREE + bit as if it was on at the time of the call. + + + + Serialize for the virtual processor’s control structure + with H_PROD. + + + + If the virtual processor’s “prod” bit is set, + then: + + + + Reset the virtual processor’s “prod” + bit. + + + + Release the virtual processor’s control structure. + + + + Return H_Success. + + + + + + Record all the virtual processor architected state including the + Time Base and Decrementer values. + + + + Set hypervisor timer services to wake the virtual processor per + the setting of the decrementer. + + + + Mark the virtual processor as non-dispatchable until the + processor is the target of an interrupt (system reset, external including + decrementer or IPI) or PROD. + + + + Cede the time remaining in the virtual processor’s time + slice preferentially to the virtual processor’s partition. + + + + Release the virtual processor’s control structure. + + + + Dispatch some other virtual processor + + + + Return H_Success. + + + + + + R1--1. + + For the SPLPAR option: The platform must implement + the H_CEDE hcall() following the syntax and semantics of + . + + + + +
+ +
+ H_CONFER + The architectural intent of this hcall() is to confer the callers + processor capacity to the holder of a lock or the initiator of an event + that the caller is waiting upon. If the caller knows the identity of the + lock holder then the holder’s virtual processor number is supplied + as a parameter, if the caller does not know the identity of the lock + holder then the “all processors” value of the proc parameter + is specified. If the caller is conferring to the initiator of an event + the proc parameter value of the calling processor. This call may be made + with interrupts enabled or disabled. This call provides a reduced + “kill set” of volatile registers, GPRs r0 and r4-r13 are + preserved. + + Software Note: The floating point registers may not + be preserved by this call if the “Maintain FPRs” field of the + VPA =0, see + . + + + Syntax: + + + + + + + Semantics: + + + + Validate the proc number else return H_Parameter. Valid + Values: + + + + -1 (all partition processors) + + + + 0 through N one of the processor numbers of the calling processor's + partition + + + + The calling processor's number forces a confer until the calling + processor is PRODed + + + + + + If the proc number is for a single processor and the single + processor is not the calling processor, then + + + + If the dispatch parameter is not equal to the specified + processor’s hypervisor copy of the dispatch number or the + hypervisor copy of the dispatch number is even, then return + H_Success. + + + + If the target processor has conferred its cycles to all others, + then return H_Success. + + + + Firmware Implementation Note: If one were to confer + to a processor that had conferred to all, then a dead lock could occur, + however, there are valid cases with nested locks were this could happen, + therefore, the hypervisor call silently ignores the confer. + + + + Record all the virtual processor architected state including the + Time Base and Decrementer values. + + + + If the MSREE bit is on, + set hypervisor timer services to wake + the virtual processor per the setting of the decrementer. + + + + Mark the virtual processor as non-dispatchable until one of the + following: + + + + System reset interrupt. + + + + The MSREE bit is + on and the virtual processor is the target + of an external interrupt (including decrementer or IPI). + + + + The virtual processor is the target of a PROD operation. + + + + The specified target processor (or all partition processors if + the proc parameter value is a minus 1) have had the opportunity of a + dispatch cycle. + + + + + + Confer the time remaining in the virtual processor’s time + slice to the virtual processor’s partition. + + + + Dispatch the/a partition target virtual processor. + + + + Return H_Success. + + + + + + R1--1. + + For the SPLPAR option: The platform must implement + the H_CONFER hcall() following the syntax and semantics of + . + + + + + R1--2. + + For the SPLPAR option: The platform must implement + the H_CONFER hcall() such that the only GPR that is modified by the call + is r3. + + + + + +
+ +
+ H_PROD + Awakens the specific processor. This call provides a reduced + “kill set” of volatile registers, GPRs r0 and r4-r13 are + preserved. + + + Syntax: + + + + + + + Semantics: + + + + Verify that the target virtual processor specified by the proc + parameter is owned by the calling virtual processor’s + partition. + + + + Serialize for the Target Virtual Processor’s control + structure with H_CEDE. + + + + Set “prod” bit in the target virtual + processor’s control structure. + + + + If the target virtual processor is not ready to run, mark the + target virtual processor ready to run. + + + + Release the target virtual processor’s control + structure. + + + + Return H_Success. + + + + + + R1--1. + + For the SPLPAR option: The platform must implement + the H_PROD hcall() following the syntax and semantics of + . + + + + + R1--2. + + For the SPLPAR option: The platform must implement + the H_PROD hcall() such that the only GPR that is modified by the call is + r3. + + + + + +
+ +
+ H_GET_PPP + This hcall() returns the partition’s performance parameters. + The parameters are packed into registers: + + + + Register R4 contains the Entitled Processor Capacity Percentage + for the partition. In the case of a dedicated processor partition this + value is 100* the number of processors owned by the partition. + + + + Register R5 contains the Unallocated Processor Capacity + Percentage for the calling partition’s aggregation. + + + + Register R6 contains the aggregation numbers of up to 4 levels of + aggregations that the partition may be a member. + + + + Bytes 0-1: Reserved for future aggregation definition, and set to + zero -- in the future this field may be given meaning. + + + + Bytes 2-3: Reserved for future aggregation definition, and set to + zero -- in the future this field may be given meaning. + + + + Bytes 4-5: 16 bit binary representation of the “Group + Number”. + + + + Bytes 6-7: 16 bit binary representation of the “Pool + Number”. In the case of a dedicated processor partition the + “Pool Number” is not applicable which is represented by the + code 0xFFFF. + + + + + + Register R7 contains the platform resource capacities: + + + + Bytes 0 Reserved for future platform resource capacity + definition, set to zero -- in the future this field may be given + meaning. + + + + Byte 1 is a bit field representing the capping mode of the + partition’s virtual processor(s): + + + + Bits 0-6 are reserved, and set to zero -- in the future these + bits may be given meaning as new capping modes are defined + + + + Bit 7 -- The partition’s virtual processor(s) are capped at + their Entitled Processor Capacity Percentage. In the case of dedicated + processors this bit is set. + + + + + + Byte 2: Variable Processor Capacity Weight. In the case of a + dedicated processor partition this value is 0x00. + + + + Byte 3: Unallocated Variable Processor Capacity Weight for the + calling partition’s aggregation. + + + + Bytes 4-5 16 bit unsigned binary representation of the number of + processors active in the caller’s Processor Pool. In the case of a + dedicated processor partition this value is 0x00. + + + + Bytes 6-7 16 bit binary representation of the number of + processors active on the platform. + + + + + + When the value of the + “ibm,partition-performance-parameters-level” see + ) is >=1 then register R8 contains + the processor virtualization resource allocations. In the case of a + dedicated processor partition R8 contains 0: + + + + Bytes 0-1: 16 bit unsigned binary representation of the number of + physical platform processors allocated to processor + virtualization. + + + + Bytes 2-4: 24 bit unsigned binary representation of the maximum + processor capacity percentage that is available to the partition's + pool. + + + + Bytes 5-7: 24 bit unsigned binary representation of the entitled + processor capacity percentage available to the partition's pool. + + + + + + + + Syntax: + + + + + + + Semantics: + + + + Place the partition’s performance parameters for the + calling virtual processor’s partition into the respective + registers: + + + + R4: The calling partition’s Entitled Processor Capacity + Percentage + + + + R5: The calling partition’s aggregation’s Unallocated + Processor Capacity Percentage. + + + + R6: The aggregation numbers + + + + R7: The platform resource capacities + + + + R8: When + “ibm,partition-performance-parameters-level” is + >= 1 in the device tree, R8 is loaded with the processor + virtualization resource allocations + + + + Return H_Success. + + + + + + + + R1--1. + + For the SPLPAR option: The platform must implement + the H_GET_PPP hcall() following the syntax and semantics of + . + + + + +
+ +
+ H_SET_PPP + This hcall() allows the partition to modify its entitled processor + capacity percentage and variable processor capacity weight within limits. + If one or both request parameters exceed the constraints of the calling + LPAR’s environment, the hypervisor limits the set value to the + constrained value and returns H_Constrained. The H_GET_PPP call may be + used to determine the actual current operational values. By the + hypervisor constraining the actual values, the calling partition does not + need special authority to make the H_SET_PPP hcall(). + See + for definitions of these + values. + + + Syntax: + + + + + + + Semantics: + + + + Verify that the variable processor capacity weight is between 0 + and 255 else return H_Parameter. + + + + Verify that the capacities specified is within the constraints of + the partition: + + + + If yes, atomically set the partition’s entitled and + variable capacity per the request and return H_Success. + + + + If not set the partition’s entitled and variable capacity + as constrained by the partition’s configuration and return + H_Constrained. + + + + + + Firmware Implementation Note: If the dispatch algorithm requires + that the summation of variable capacities be updated, it is atomically + updated with the set of the partition’s weight. + + + + R1--1. + + For the SPLPAR option: The platform must implement + and make available to selected partitions, the H_SET_PPP hcall() + following the syntax and semantics of + . + + + + +
+ +
+ H_PURR + The Processor Utilization of Resources Register (PURR) is + compatibly read through the H_PURR hcall(). In those implementations + running on processors that do not implement the register in hardware, + firmware simulates the function. On platforms that present the property + “ibm,rks-hcalls” with bit 2 set (see + ), this call provides a reduced + “kill set” of volatile registers, GPRs r0 and r5-r13 are + preserved. + + + Syntax: + + + + + + + Semantics: + + + + If the platform presents the + “ibm,rks-hcall” property with bit 2 set; + then honor a kill set of volatile registers r3 & r4. + + + + Compute the PURR value for the calling virtual processor up to + the current point in time and place in R4 + + + + Return H_Success. + + + + + + R1--1. + + For the SPLPAR option: The platform must implement + the H_PURR hcall() following the syntax and semantics of + . + + + + +
+ +
+ H_POLL_PENDING + Certain implementations of the hypervisor steal processor cycles to + perform administrative functions in the background. The purpose of the + H_POLL_PENDING hcall() is to provide a OS, running atop such an + implementation, with a hint of pending work so that it may more + intelligently manage use of platform resources. The use of this call by + an OS is totally optional since such an implementation also uses hardware + mechanisms to ensure that the required cycles can be transparently + stolen. It is assumed that the caller of H_POLL_PENDING is idle, if all + threads of the processor are idle (as indicated by the idle flag at byte + offset 0xFE of + ), the hypervisor may choose to + perform a background administrative task. The hypervisor returns + H_PENDING if there is pending administrative work, at the time of the + call, that it could dispatch to the calling processor if the calling + processor were ceded, if there is no such pending work, the return code + is H_Success. Due to race conditions, this pending work may have grown or + disappeared by the time the calling OS makes a subsequent H_CEDE + call. + There is NO architectural guarantee that ceding a processor exempts + a virtual processor from preemption for a given period of time. That may + indeed be the characteristic of a given implementation, but cannot be + expected from all future implementations. + + + Syntax: + + + + + + + Semantics: + + + + Return H_PENDING if there is work pending that could be + dispatched to the calling processor if it were ceded, else return + H_Success. + + + + + + R1--1. + + For the SPLPAR option: The platform must implement + the H_POLL_PENDING hcall() following the syntax and semantics of + . + + + + + +
+ +
+ +
+ Pool Idle Count Function Set + The hcall-pic function set may be configured via the partition + definition in none or any number of partitions as the weights + administrative policy dictates. + +
+ H_PIC + + + + Syntax: + + + + + + + Semantics: + + + + Verify that calling partition has the authority to make the call + else return H_Authority. + + + + Compute the PIC value for the processor pool implementing the + calling virtual processor up to the current point in time and place into + R4 + + + + Place the number of processors in the caller’s processor + pool in R5. + + + + When the value of the + “ibm,partition-performance-parameters-level” (see + ) is >=1 then: + + + + Place the summation of time base ticks for all platform + processors, allocated to the caller's processor pool, into register + R6. + + + + Place the summation of all PURR ticks accumulated by all + dispatched (not idle) platform processor threads, allocated to the + caller's processor pool, into register R7. + + + + Place the summation of all SPURR + Machines that do not have a SPURR mechanism are assumed to run at + a constant speed, at which time the PURR value is substituted. + ticks accumulated by all dispatched (not idle) platform + processor threads, allocated to the caller's processor pool, into + register R8. + + + + Place the caller's processor pool ID into low order two bytes of + register R9 (high order 6 bytes are reserved - set to 0x000000). + + + + If the calling partition has the authority to monitor total + processor virtualization then: + + + + Place the summation of time base ticks for all platform physical + processors, allocated to processor virtualization, in register + R10. + + + + Place the summation of all PURR ticks accumulated by all + dispatched (not idle) platform physical processor threads, allocated to + processor virtualization, in register R11. + + + + Place the summation of all SPURR + ticks accumulated by all dispatched (not idle) platform + physical processor threads, allocated to processor virtualization, in + register R12. + + + + Else load R10, R11 and R12 with -1. + + + + + + + + Return H_Success. + + + + + + R1--1. + + For the SPLPAR option: The platform must implement + and make available to selected partitions, the H_PIC hcall() following + the syntax and semantics of + . + + + + +
+
+ + +
+ Thread Join Option + + +
+ H_JOIN + The H_JOIN hcall() performs the equivalent of a H_CONFER + (proc=self) hcall() (see + ) unless called by the sole + unjoined (active) processor thread, at which time the H_JOIN hcall() + returns H_CONTINUE. H_JOIN is intended to establish a single threaded + operating environment within a partition; to prevent external interrupts + from complicating this environment, H_JOIN returns “bad_mode” + if called with the processor MSR[EE] bit set to 1. Joined (inactive) + threads are activated by H_PROD (see + ) which starts execution at the + instruction following the hcall; or a system reset non-maskable interrupt + which appears to interrupt between the hcall and the instruction + following the hcall. + + + Syntax: + + + + + + + Semantics + + + + If MSR.EE=1 return bad_mode. + + + + If other processor threads are active in the calling partition, + then emulate H_CONFER (proc=self) + + + + Else return H_CONTINUE. + + + + + + R1--1. + + For the Thread Join option: The platform must + implement the H_JOIN hcall() following the syntax and semantics of + . + + + + + R1--2. + + For the Thread Join option: The platform must + implement the hcall-join and hcall-splpar function sets. + + + + + R1--3. + + For the Thread Join option: The platform must support + the H_PROD hcall even if the partition is operating in dedicated + processor mode. + + + + +
+
+ +
+ Virtual Processor Home Node Option (VPHN) + The SPLPAR option allows the platform to dispatch virtual + processors on physical processors that due to the variable nature of work + loads are temporarily free, thus improving the utilization of computing + resources. However, SPLPAR implies inconsistent mapping of virtual to + physical processors; defeating resource allocation software that attempts + to optimize performance on platforms that implement the NUMA + option. + To bridge the gap between these two options, the VPHN option + maintain a substantially consistent mapping of a given virtual processor + to a physical processor or set of processors within a given associativity + domain. Thus the OS can, when allocating computing resources, take + advantage of this statistically consistent mapping to improve processing + performance. + VPHN mappings are substantially consistent but not static. For any + given dispatch cycle, a best effort is made to dispatch the virtual + processor on a physical processor within a targeted associativity domain + (the virtual processor's home node). However, if processing capacity + within the home node is not available, some other physical processor is + assigned to meet the processing capacity entitlement. From time to time, + to optimize the total platform performance, it may be necessary for the + platform to change the home node of a given virtual processor. + To enable the OS to determine the associativity domain of the home + node of a virtual processor, platforms implementing the VPHN option + provide the H_HOME_NODE_ASSOCIATIVITY hcall(). The presence of the + hcall-vphn function set in the + “ibm,hypertas-functions” property + indicates that the platform supports the VPHN option. The OS should be + prepared for the support of the VPHN option to change with functions such + partition migration, after which a call to H_HOME_NODE_ASSOCIATIVITY may + end with a return code of H_FUNCTION. Additionally, the VPHN option + defines a VPA field that the OS can poll to determine if the + associativity domain of the home node has changed. When the home node + associativity domain changes, the OS might choose to call the + H_HOME_NODE_ASSOCIATIVITY hcall() and adjust its resource allocations + accordingly. + + + + R1--1. + + For the Virtual Processor Home Node option: The + platform must support the H_HOME_NODE_ASSOCIATIVITY hcall() per the + syntax and semantics specified in section + . + + + + + R1--2. + + For the Virtual Processor Home Node option: For the + OS to operate properly across such functions as partition migration, the + OS must be prepared for the target platform to not support the Virtual + Processor Home Node option. + + + + + R1--3. + + For the Virtual Processor Home Node option: The + platform must support the “virtual processor home node + associativity changes counters” field in the VPA per section + . + + + + + R1--4. + + For the Virtual Processor Home Node option: The + platform must support the “Form 1” of the + “ibm,associativity-reference-points” property per + . The client program may call + H_HOME_NODE_ASSOCIATIVITY hcall() with a valid identifier input parameter + (such as from the device tree or from the + ibm,configure-connector RTAS call) even if the + corresponding virtual processor has not been started so that the client + program can allocate resources optimally with respect to the to be + started virtual processor. + + + + +
+ H_HOME_NODE_ASSOCIATIVITY + The H_HOME_NODE_ASSOCIATIVITY hcall() returns the associativity + domain designation associated with the identifier input parameter. The + client program may call H_HOME_NODE_ASSOCIATIVITY hcall() with a valid + identifier input parameter (such as from the device tree or from the + + ibm,configure-connector RTAS call) even if the + corresponding virtual processor has not been started so that the client + program can allocate resources optimally with respect to the to be + started virtual processor. + + + Syntax: + + + + + + + Parameters: + + + + Input: + + + + flags: + + + + Note: this parameter does not share format with the flags + parameter of the Page Frame Table Access hcall()s. + + + + Defined Values: + + + + 0x0 Invalid + + + + 0x1 id parameter is as proc-no parameter of H_REGISTER_VPA + hcall() + + + + 0x2 id parameter is as processor index from byte offsets 0x2-0x3 + of a trace log buffer entry + + + + all other values reserved. + + + + + + + + id: processor identifier per the form indicated by the flags + parameter. + + + + + + Output: + + + + R3: return code + + + + R4-R9: associativity domain identifier list of the specified + processor’s home node. + + + + Only the “primary” connection (as would be reported + in the first string of the + “ibm,associativity” property) is + reported. + + + + The associativity domain numbers are reported in the sequence + they would appear in the + “ibm,associativity” property; starting + from the high order bytes of R4 proceeding toward the low order bytes of + R9. + + + + Each of the registers R4-R9 is divided into 4 fields each 2 bytes + long. + + + + The high order bit of each 2 byte field is a length + specifier: + + + + 1: The associativity domain number is contained in the low order + 15 bits of the field, + + + + 0: The associativity domain number is contained in the low order + 15 bits of the current field concatenated with the 16 bits of the next + sequential field) + + + + + + All low order fields not required to specify the associativity + domain identifier list contain the reserved value of all ones. + + + + + + + + + + Semantics: + + + + Verify that the “flags” parameter is valid else + return H_Parameter. + + + + Verify that the “id” parameter is valid for the + “flags” and the partition else return H_P2. + + + + Pack the associativity domain identifiers for the home node + associated with the “id” parameter starting with the highest + level reported in the + “ibm,associativity” property in the high + order field of R4. + + + + All remaining fields through the low order field of R9 are filled + with 0xFFFFFFFF. + + + + Return H_Success. + + + + +
+ +
+ VPA Home Node Associativity Changes Counters + For the VPHN option, the platform maintains within each VPA the + Virtual Processor Home Node Associativity Change Counters field. See + Table + . This eight (8) byte field is + maintained as 8 one byte long counters. The number of counters that are + supported is implementation dependent up to 8, and corresponds to the + entries in the form 1 of the + “ibm,associativity-reference-points” property. If + the platform implements fewer than 8 associativity reference points, only + the corresponding low offset counters within the field are used and the + remaining high offset counters within the field are unused. + Should the associativity of the home node of the virtual processor + change, for each changed associativity level that corresponds to a level + reported in the + “ibm,associativity-reference-points” property, the + corresponding counter in the Virtual Processor Home Node Associativity + Change Counters field is incremented. +
+ +
+
+ +
+ Virtualizing Partition Memory + This section describes the various high level functions that are + enabled by the virtualization of the logical real memory of a partition. In + principle, virtualization of partition memory can be totally transparent to + the partition software; however, partition software that is migration aware + can cooperate with the platform to achieve higher performance, and enhanced + functionality. + +
+ Partition Migration/Hibernation + Virtualizing partition memory allows a partition to be moved via + migration or hibernation. In the case of partition migration from one + platform to another, the source and destination platforms cooperate to + minimize the time that the partition is non-responsive; the goal is to be + non-responsive no more than a few seconds. In the case of hibernation, + the intent is to put the partition to sleep for an extended period; + during this time the partition state is stored on secondary storage for + later restoration. + + + + R1--1. + + For the Partition Migration and Partition Hibernation + options: The platform must implement the Partition Suspension + option (See + ). + + + + + R1--2. + + + Reserved + + + + + R1--3. + + For the Partition Migration and Partition Hibernation + options: The platform must implement the Update OF Tree + option. + + + + + R1--4. + + For the Partition Migration and Partition Hibernation + options: The platform must implement the Version 6 Extensions + of Event Log Format for all reported events (See + ). + + + + + R1--5. + + For the Partition Migration and Partition Hibernation + options: The platform must prevent the migration/hibernation of + partitions that own dedicated platform resources in addition to + processors and memory, this includes physical I/O resources, the BSR + facility, physical indicators and sensors (virtualized I/O, indicators + (such as tone) and sensors (such as EPOW) are allowed). + + + + + R1--6. + + For the Partition Migration and Partition Hibernation + options: The platform must implement the Client Vterm + option. + + + + + R1--7. + + For the Partition Migration and Partition Hibernation + options: The platform + “timebase-frequency” must be 512 MHz. +/- + 50 parts per million. + + + + + R1--8. + + For the Partition Migration and Partition Hibernation + options: The platform must present the + “ibm,nominal-tbf” property (See + ) with the value of 512 MHz. + + + + + R1--9. + + For the Partition Suspension option: The platform + must present the properties from + , as specified by + , to a partition. + + + + + R1--10. + + For the Partition Suspension option: The presence and + value of all properties in + must not change while a + partition is suspended except for those properties described by + . + + + + + + Properties Related to the Partition Suspension Option + + + + + + + + Property Name + + + + + Requirement + + + + + + + + + “ibm,estimate-precision” + + + + Shall be present. + “ibm,estimate-precision” shall + contain the “fre”, “fres”, + frsqrte”, and “frsqrtes” instruction + mnemonics. + + + + + + “ibm,processor-page-sizes” + + + + Shall be present. + + + + + + “reservation-granule-size” + + + + Shall be present. + + + + + + “cache-unified” + + + + Shall be present if the cache is physically or logically + unified and thus does not require the architected instruction + sequence for data cache stores to appear in the instruction + cache (See “Instruction Storage” section of Book II + of PA); else shall not be present. + + + + + + “i-cache-size” + + + + Shall be present. + + + + + + “d-cache-size” + + + + Shall be present. + + + + + + “i-cache-line-size” + + + + Shall be present. + + + + + + “d-cache-line-size” + + + + Shall be present. + + + + + + “i-cache-block-size” + + + + Shall be present. + + + + + + “d-cache-block-size” + + + + Shall be present. + + + + + + “i-cache-sets” + + + + Shall be present. + + + + + + “d-cache-sets” + + + + Shall be present. + + + + + + “timebase-frequency” + + + + Shall be present if the timebase frequency can fit into + the + “timebase-frequency” property; + else shall not be present. + + + + + “ibm,extended-timebase-frequency” + + + Shall be present if the timebase frequency cannot fit + into the + “timebase-frequency” property; else + shall not be present. + + + + + + “slb-size” + + + + Shall be present. + + + + + + “cpu-version” + + + + Shall be present. + + + + + + “ibm,ppc-interrupt-server#s” + + + + Shall be present. + + + + + + “l2-cache” + + + + Shall be present if another level of cache exists; else + shall not be present. + + + + + + “ibm,vmx” + + + + Shall be present if VMX is present for the partition; + else shall not be present. + + + + + + “clock-frequency” + + + + Shall be present if the processor frequency can fit into + the + “clock-frequency” property; + else shall not be present. + + + + + “ibm,extended-clock-frequency” + + + Shall be present if the processor frequency cannot fit + into the + “clock-frequency” property; else shall + not be present. + + + + + + “ibm,processor-storage-keys” + + + + Shall be present. + + + + + + “ibm,processor-vadd-size” + + + + Shall be present. + + + + + + “ibm,processor-segment-sizes” + + + + Shall be present. + + + + + “ibm,segment-page-sizes” + + + Shall be present. + + + + + + “64-bit” + + + + Shall be present. + + + + + + “ibm,dfp” + + + + Shall be present if DFP is present for the partition; + else shall not be present. + + + + + “ibm,purr” + + + Shall be present if a PURR is present; else shall not be + present. + + + + + “performance-monitor” + + + Shall be present if a Performance Monitor is present; + else shall not be present. + + + + + “32-64-bridge” + + + Shall be present. + + + + + “external-control” + + + Shall not be present. + + + + + “general-purpose” + + + Shall be present. + + + + + “graphics” + + + Shall be present. + + + + + “ibm,platform-hardware-notification” + + + Shall be present. + + + + + “603-translation” + + + Shall not be present. + + + + + “603-power-management” + + + Shall not be present. + + + + + “tlb-size” + + + Shall be present. + + + + + “tlb-sets” + + + Shall be present. + + + + + “tlb-split” + + + Shall be present. + + + + + “d-tlb-size” + + + Shall be present. + + + + + “d-tlb-sets” + + + Shall be present. + + + + + “i-tlb-size” + + + Shall be present. + + + + + “i-tlb-sets” + + + Shall be present. + + + + + “64-bit-virtual-address” + + + Shall not be present. + + + + + “bus-frequency” + + + Shall be present if the bus frequency can fit into the + “bus-frequency” property; else + shall not be present. + + + + + “ibm,extended-bus-frequency” + + + Shall be present if the processor frequency cannot fit + into the + “bus-frequency” property; else shall + not be present. + + + + + “ibm,spurr” + + + Shall be present if an SPURR is present; else shall not + be present. + + + + + “name” + + + Shall be present. + + + + + “device_type” + + + Shall be present. + + + + + “reg” + + + Shall be present. + + + + + “status” + + + Shall be present. + + + + + “ibm,pa-features” + + + Shall be present. + + + + + “ibm,negotiated-pa-features” + + + Shall be present + + + + + + “ibm,ppc-interrupt-gserver#s” + + + + Shall be present + + + + + + “ibm,tbu40-offset” + + + + Shall be present + + + + + + “ibm,pi-features ” + + + + Shall be present + + + + + + “ibm,pa-optimizations” + + + + Shall be present + + + + +
+ Note on : The values of the + properties in Table + shall be consistent with + implementation and design of the processor and the platform upon boot as + well as before and after partition suspension. + + Programming Note: The + “cpu-version” property may contain a + logical processor version value. Therefore, code designed to handle + processor errata should read the + “ibm,platform-hardware-notification” property of + the root node to obtain the physical processor version numbers allowed in + the platform. +
+ +
+ Virtualizing the Real Mode Area + PA requires implementations to provide a Real Mode Area of memory + that is accessed when not in hypervisor state (either MSR[HV] = 0, or + MSR[HV] = 1 and MSR[PR] = 1) and the OS address translation mechanism is + disabled (MSR[IR] = 0 or MSR[DR] = 0). PA provides mechanisms to allow + the RMA to consist of discontiguous pages of selectable sizes. Such an + RMA is known as a virtualized RMA. The H_VRMASD hcall() allows the OS to + change the characteristics of the mappings the address translation + mechanism uses to access a virtualized RMA. + +
+ H_VRMASD + The caller may need to invoke the H_VRMASD hcall() multiple times + for it to return with a return code of H_Success. Upon receiving a return + code of H_LongBusyOrder10mSec, the caller should attempt to invoke + H_VRMASD in 10 mSec with the same Page_Size_Code value used on the + previous H_VRMASD hcall(). Invoking H_VRMASD with a different + Page_Size_Code value indicates that the caller wants to transition to the + Page_Size_Code value of the most recent H_VRMASD call. + When changing the page size used to map the VRMA using the H_VRMASD + hcall(), the caller is responsible for establishing HPT entries for any + potential real mode accesses prior to calling H_VRMASD with a new value + of Page_Size_Code, and maintaining any HPT entries for the old value of + Page_Size_Code until the hcall() returns H_Success. + + + + R1--1. + + For the VRMA option: The platform must include the + “ibm,vrma-page-sizes” property (See + ) in the + /cpu node. + + + + + R1--2. + + For the VRMA option: The platform must implement the + H_VRMASD hcall() following the syntax and semantics of + . + + + + + R1--3. + + For the VRMA option: In order to prevent a storage + exception, the calling partition must establish page table mappings for + the Real Mode Area using entries with a page size corresponding to the + new Page_Size_Code value prior to making an H_VRMASD hcall() and must + maintain the old page table mappings using the page size corresponding to + the old Page_Size_Code value until the H_VRMASD hcall() returns + H_Success. + + + + + + Syntax: + + + + + + + Parameters: + + + Page_Size_Code: A supported VRMASD field value. Supported VRMASD + field values are described by the + “ibm,vrma-page-sizes” property. + + + + + + Semantics: + + + + Verify that the Page_Size_Code parameter corresponds to a + supported VRMASD field value; else return H_Parameter. + + + + If the Real Mode Area page size specified by the Page_Size_Code + parameter does not match the operating RMA page size of the partition, + then set the operating RMA page size of the partition to the value + specified by the Page_Size_Code parameter and initiate the transition of + the operating RMA page size of all active processing threads to the value + specified by the Page_Size_Code parameter. + + + + If all active threads have transitioned to the partition + operating RMA page size, then return H_Success; else return + H_LongBusyOrder10mSec. + + + +
+
+ +
+ Cooperative Memory Over-commitment Option (CMO) + Cooperative Memory Over-commitment Option (CMO) + The over-commitment of logical memory is accomplished by the + platform reassigning pages of memory among the partitions to create the + appearance of more memory than is actually present. This is commonly + known as paging. While paging can, in certain cases, be accomplished + transparently, significantly better memory utilization and platform + performance can be achieved with cooperation from the partition + OS. + CMO introduces the following LoPAR terms: + + + + Expropriation: + + The act of the platform disassociating a physical + page from a logical page. + + + + + Subvention: + + The act of the platform associating a physical page + with a logical page. + + + + + Loaned Memory: + + Logical real memory that a partition lends to the + hypervisor for reuse. The partition should not gratuitously access loaned + memory as such accesses are likely to experience a significant + delay. + + + + + Memory entitlement: + + The amount of memory that the platform + guarantees that the partition is able to I/O map at any given + time. + + + + + + + R1--1. + + For the CMO option: The partition must be running + under the SPLPAR option. + + + + + R1--2. + + For the CMO option: The platform must transparently + (except for time delays) handle all effects of any memory expropriation + that it may introduce unless the CMO option is explicitly enabled by the + setting of architecture.vec option vector 5 byte 4 bit 0 (See + for details). + The CMO option consists of the following LoPAR extensions: + + + + Define + ibm,architectue.vec-5 option Byte 4 bit 0 as + “Client supports cooperative logical real memory + over-commitment”. + + + Define page usage states to assist the platform in selecting good + victim pages and mechanisms to set such states. + + + Extend the syntax and semantics defined for the I/O mapping + hcall()s + + + + Return codes (H_LongBusyOrder1msec, H_LongBusyOrder10msec, and + H_NOT_ENOUGH_RESOURCES) + + + + Return parameter extension for memory entitlement + management + + + + + Define a simulated Special Uncorrectable memory Error machine + check for the case where a page can not be restored due to an + error. + + + + + + + R1--3. + + For the CMO option: The architected interface syntax + and semantics of all LoPAR hcall()s and RTAS calls except as explicitly + modified per the CMO option architecture must remain invariant when + operating in CMO mode; any accommodation to memory over-commitment by + these firmware functions (potentially any function that takes a logical + real address as an input parameter) is handled transparently. + Note: Requirement + specifically applies to the + debugger support hcall()s. + For maximum performance benefit, an OS that indicates via the + ibm,client-architecture-support interface that it + supports the CMO option will strive to maintain in the + “loaned” state (See + ), the amount of logical memory + indicated by the value returned in R9 from the H_GET_MPP hcall (See + ), as well as provide page + usage state information via the interfaces defined in + and + . + The Extended Cooperative Memory Over-commitment Option (XCMO) + provides additional features to manage page coalescing. These features + are activated via setting architecture.vec vector 5 byte 4 bit 1 to the + value of 1 in the + ibm,client-architecture-support interface. Given that + the platform supports the XCMO option, the CC flag for page frame table + Accesses see + and the H_GET_MPP_X hcall() see + + may be used by the OS. An OS + might understand that a given page is a great candidate for page + coalescing perhaps because the page contains OS and or common library + code which is likely to be duplicated in other partitions; if so it might + choose to set the Coalesce Candidate (CC) flag in the page table access + or H_PAGE_INIT hcall()s as a hint to the hypervisor. Should a given + logical page be mapped multiple times with conflicting Coalesce Candidate + hints, the value in the last mapping made takes precedence. + For a variety of reasons outside the scope of LoPAR, a platform + supporting the XCMO option for a given platform might not actually + perform page coalescing. If this is the case, the first return value from + the H_GET_MPP_X hcall() see + is the reserved value + zero. + + + + + R1--4. + + For the XCMO Option: The platform must implement the + CMO Option. + + + + + R1--5. + + Reserved for Compatibility For the XCMO Option: The + platform must implement the CC (Coalesce Candidate) flag bit see + . + + + + + R1--6. + + For the XCMO Option: The platform must implement the + H_GET_MPP_X hcall() see + . + + + + + R1--7. + + For the XCMO Option with the Partition Migration and + Partition Hibernation options: to ensure proper operation after partition + migration or hibernation, the OS must stop setting the CC flag bit see + and stop calling the + H_GET_MPP_X hcall() see + prior to calling + ibm,suspend-me RTAS and not do so again until after + the OS has determined that the XCMO option is supported on the + destination platform. + + + + + +
+ CMO Background (Informative) + The following information is provided to be informative of the + architectural intent. Implementations may vary, but should make a best + effort to achieve the goals described. + Ideally, the hypervisor does not expropriate any logical memory + pages that it must later read in from disk; this is based upon the belief + that the OS is in a better position to determine its working set relative + to the available memory and page its memory than the hypervisor thus, + when possible, the OS pager should be used. The ideal is approximated, + since it cannot be achieved in all cases. The “Overage” is + defined as the amount of logical address space that cannot be backed by + the physical main storage pool. The overage is equal to the summation of + the logical address space for all partitions using a given VRM main + storage pool (the main storage that the hypervisor uses to back logical + memory pages for a set of partitions) plus the high water mark of the + hypervisor free page list (the free list high water mark is some + implementation dependent ratio of the pool size) less the size of the VRM + main storage pool. + If the summation of the space freed by page coalescing and page + donation is equal to the overage, in the steady state the hypervisor need + not page. In reality the system is seldom, if ever, in the steady state, + but with the free list pages the hypervisor has enough buffer space to + take up most of the transient cases. + Page coalescing is a transparent operation where in the hypervisor + detects duplicate pages, directs all user reads to a single copy and may + reclaim the other duplicate physical memory pages. Should the page owner + change a coalesced page the hypervisor needs to transparently provide the + page owner with a unique copy of the page. Read only pages are more + likely to remain identical for a longer period of time and are thus + better coalescing candidates. + To set the value for the partition's page donation, the algorithm + needs to be “fair” and responsive to the partition's + “weight” so that more important work can be helped along. To + be “fair”, the donation needs to be somewhat proportional to + the partition's size since donating x pages is likely to cause greater + pain to a small partition than a large one; yet the reason for + “weight” is to cause greater pain to certain partitions + relative to others. + Thus the initial donation for a partition is set at the partition's + logical address space size as a percentage of the total pool logical + space subscription times the overage. + Each implementation dependent time interval (say single digit + seconds or so), the hypervisor randomly selects 100 pages from each + partition and monitors how many of them were accessed during the next + interval. This, after normalization to account for partition CPU + utilization relative to its recent maximum, becomes an estimate of the + partition's page utilization. It is expected that a partition with higher + page utilization has a higher page fault rate and a lower percentage of + its working set resident -- thus experiences more pain from VRM. + The page utilization method described above may over estimate + memory pressure in certain cases; specifically it may be slow to realize + that the partition has gone idle. An idle partition reduces its CPU + utilization which after normalization makes it appear that the partition + memory pressure has risen rather than lowered. For this reason, the + results of the page utilization method is further compared with the OS + reported count of faults against pages that were previously swapped out + as reported in offsets 0x180 - 0x183 of the VPA for each of the + partition processors. The partition fault count when normalized with + respect to processor cycles allows comparisons among the reported values + from other partitions. Since the partition fault count is OS reported, + and thus can not be trusted, it can not be the primary value used to + determine page allocation, but since if the OS is misreporting the + statistic, it is likely to be high, the memory pressure estimate derived + from the OS reported fault counts can be used to reduce (but not + increase) the partition memory allocation. Note since the hint might not + be reported by a given OS, a filter should be put in place to detect that + the OS is not reporting faults and appropriate default values + substituted. + This initial donation is then modified over time to force the pain + of higher page utilization upon lower weight partitions based upon + comparing the following ratios: + A: The average partition page utilization over the last interval of + all partitions in the pool / the partition's page utilization over the + last interval + B: The partition's weight/average partition weight of all + partitions in the pool + If A > B Increase the partition's donation by 1/256 of the + partition's logical address space (limited to the partition’s + logical address size) + If A < B Reduce the partition's donation by 1/256 of the + partition's logical address space provided that the summation of all + donations >= Overage. + The hypervisor maintains a per partition count of loaned pages + (incremented when a page is removed from the PFT with a + “loaned” state and decremented when/if the page state is + changed) thus it can keep track of how well a partition is doing against + the donation request that has been made of it. Partitions that do not + respond to donation requests need + to have their pages stolen to make up the difference. Pages that + are “unused” or “loaned” are automatically + applied to the free list. “Loaned” pages are expected to + raise the partition's free list low water mark so that the OS only + reclaims them in a transient situation which will then result in the OS + paging out some of its own virtual memory to restore the total donation + in the steady state. When the platform free list gets to the low water + mark, pages are expropriated starting with the partition that has the + greatest percentage discrepancy between its loaned plus expropriated + count and is donation tax. The algorithm used is implementation + dependent. The following is given for reference and is loosely based upon + the AIX method. + + + + For this algorithm, pages that are newly restored are marked as + “referenced” and all “unused” have already been + harvested + + + + Step through the partition logical address space until either + the hypervisor free list has gotten to its high water mark or the + partition has been taxed to its donation. + + + + If the page is I/O mapped and not expropriatable, continue to + the next page. + + + + If this is the first pass through the address space on this + harvest, and the page is marked critical, continue to the next + page. + + + + If the page is marked “referenced”, clear the + reference bit and continue to the next page. + + + + If the page is backed in the VPM paging space and not modified + since then, expropriate the page and continue to the next page. + + + + Queue the page to be copied into the VPM paging space. + + + + + + Thus partitions that keep up with their page donations seldom, if + ever, experience a hypervisor page in delay. Those that do not keep up, + will not get a free lunch and will be taxed up to the value of their + assigned donation, with the real possibility that they will experience + the pain of hypervisor page in delays. +
+ +
+ CMO Page Usage States + The CMO option defines a number of page states that are set by the + cooperating OS using the flags parameter of the HPT hcall()s. The + platform uses these page states to estimate the overhead associated with + expropriating the specific page. + + Note: that the first two definitions below represent + base background page states; the 3rd definition is the foreground state + of I/O mapped which is acquired as result of an I/O mapping hcall (such + as H_PUT_TCE); and the last two are caller specifiable state + modifiers/extended semantics of the base states. + + + + Unused + + The page contains no information that is needed in + the future, its contents need not be maintained by the platform, normally + set only when the page is unmapped. + Expropriation of “Unused” pages should be a low + overhead operation. However, the OS is likely to reuse these pages + which means that a clean free page will have to be assigned to the + corresponding logical address. + + + + + + Active + + The page retains data that the OS has no + reasonable way to regenerate. This is the state traditionally assumed by + the OS when mapping a page. + “Active” pages should be expropriated only as a last + resort since they must be paged out and paged back in on a subsequent + access. + + + + + + I/O Mapped + + The page is mapped for access by another + agent. This state is the side effect of registration and/or I/O mapping + functions. The page returns to its background state automatically when + unmapped or deregistered. + Pages in the I/O Mapped state normally may not be expropriated + since they are potentially the target of physical DMA + operations. + + + + + + Critical + + The page is critical to the performance of the + OS, and the hypervisor should avoid expropriating such pages while other + pages are available. + Expropriating pages marked “Critical” may result in + the OS being unable to meet its performance goals. + + + + + + Loaned + + The page contains no information and the OS + warrants that it will not gratuitously access this page such that the + hypervisor may expect to use it for an extended period of time. When the + OS does access the page, it is likely that the access will result in a + subvention delay. + Expropriating pages in the “Loaned” state should + result in the lowest overhead. + + + + + + + + R1--1. + + For the CMO option: The platform must at partition + boot initialize the page usage state of all platform pages to + “Active”. + + + + + R1--2. + + For the CMO option: The platform must preserve data + in pages that are in the “Active” state. + + + + + R1--3. + + For the CMO option: When the OS accesses a page in + the “Unused” state, the platform must present either the + preserved page data or all zeros. + + + + + R1--4. + + For the CMO option: When the OS specifies as input to + an I/O mapping or the H_MIGRATE_DMA hcall() a page in either the + “Unused” or “Loaned” states, the platform must + upgrade the page’s background page state to + “Active”. + + + + +
+ Setting CMO Page Usage States using HPT hcall() flags + Parameter + The CMO option defines additional flags parameter combinations for + the HPT hcall()s that take a flags parameter. Turning on flags bit 28 + activates the changing of page state. Leaving bit 28 at the legacy value + of zero maintains the page state setting, thus allowing legacy code to + operate unmodified with all pages remaining in the initialized + “Active” state. + + + + R1--1. + + For the CMO option: The platform must extend the + syntax and semantics of the HPT access hcall()s that take a flags + parameter, see + , to set the page usage state + of the specified page per + . + + + + + + HPT hcall()s extended with CMO flags + + + + + + + + hcall + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +
+ + + + + CMO Page Usage State flags Definition + + + + + + + + + + + Flag bit 28 + + + + + Flag bits 29 - 30 + + + + + Flag bit 31 + + + + + Comments + + + + + + + + 0 + + + Don’t Care + + + Don’t Care + + + Inhibit Page State Change + + + + + 1 + + + 00 + + + 0 + + + Set page state to Active + + + + + 00 + + + 1 + + + Set page State to Active Critical + + + + + 01 + + + both 0 and 1 + + + Reserved + + + + + 10 + + + both 0 and 1 + + + Reserved + + + + + 11 + + + 0 + + + Set page state to Unused + + + + + 11 + + + 1 + + + Set page state to Unused Loaned + + + + +
+
+ +
+ Setting CMO Page Usage States with H_BULK_REMOVE + + + + R1--1. + + For the CMO option: The platform must extend the + syntax and semantics of the H_BULK_REMOVE hcall (see + ) to set the page usage state + of the specified pages per + . + + + + + + H_BULK_REMOVE Translation Specifier control/status + Byte Extended Definition for CMO Option + + + + + + + + + + + + + + + 0 + + + + + 1 + + + + + 2 + + + + + 3 + + + + + 4 + + + + + 5 + + + + + 6 + + + + + 7 + + + + + Bit Numbers + + + + + + + + type code + + +   + + + + + 0 + + + 0 + + + r0 + + + r0 + + + r0 + + + r0 + + + r0 + + + r0 + + + Unused + + + + +   + + + + + 0 + + + 1 + + + + page state + + + + r0 + + + r0 + + + req. mod. + + + Request + + + + +   + + +   + + +   + + + 0 + + + 0 + + + Absolute + + + + + 0 + + + 1 + + + andcon + + + + + 1 + + + 0 + + + APVN + + + + + 1 + + + 1 + + + not used + + + + + + 0 + + + + + 0 + + + + + Inhibit page usage state change + + + + + + + 0 + + + + + 1 + + + + + Reserved + + + + + + + 1 + + + + + 0 + + + + + For CMO option set page usage state to + “Unused” if Success + + + + + + + 1 + + + + + 1 + + + + + For CMO option set page usage state to + “Loaned” if Success + + + + + +   + + + + + 1 + + + 0 + + + return code + + + Response + + + + +   + + + 0 + + + 0 + + + R + + + C + + + r + + + r + + + Success + + + + + 0 + + + 1 + + + r + + + r + + + Not Found + + + + + 1 + + + 0 + + + H_PARM + + + + + 1 + + + 1 + + + H_HW + + + + +   + + + + + 1 + + + 1 + + + Reserved (to be zero) + + + End of String + + + + + Legion R=Reference Bit, C=Change Bit, r=reserved ignore, + r0=reserved to be zero + + + + +
+
+
+ +
+ CMO Extensions for I/O Mapping Hcall()s + If an OS were to map an excessive amount of its memory for + potential physical DMA access, little of its memory would be left for + paging; conversely, if the OS was totally prevented from I/O mapping its + memory, it could not do I/O operations. The CMO option introduces the + concept of memory entitlement. The partition’s memory entitlement + is the amount of memory that the platform guarantees that the partition + is able to I/O map at any given time. A given page may be mapped multiple + times through different LIOBNs yet it only counts once against the + partition’s I/O mapping memory entitlement. The syntax of certain + I/O mapping hcall()s is extended to return the change in the + partition’s I/O mapped memory total. The entitlement is intended to + be used to ensure forward progress of I/O operations. + + + + R1--1. + + For the CMO option: When the partition is operating + in CMO mode, the platform must extend the syntax and semantics of the I/O + mapping hcall()s specified in + as per the specifications in + and + . + + + + + + I/O Mapping hcall()s Modified by the CMO + Option. + + + + + + + + + hcall() + + + + + Base Definition on + + + + + + + + H_PUT_TCE + + + + + + + + + + H_STUFF_TCE + + + + + + + + + + H_PUT_TCE_INDIRECT + + + + + + + + + +
+ + Note: The I/O mapping hcalls H_PUT_RTCE and + H_PUT_RTCE_INDIRECT do not change the number of pages that are I/O mapped + since they simply create copies of the I/O mappings that already + exist. + +
+ CMO I/O Mapping Extended Return Codes + + + + R1--1. + + For the CMO option: The platform must ensure that the + DMA agent operating through the I/O mappings established by the hcall()s + specified in + can appear to successfully + access the associated page data of any expropriated page referenced by + the input parameters of the hcall() prior to returning the code + H_Success. + + + + + R1--2. + + For the CMO option: The platform must either extend + the return code set for the hcall()s specified in + to include H_LongBusyOrder1msec + and/or H_LongBusyOrder10msec or transparently suspend the calling virtual + processor for cases where the function is delayed pending the restoration + of an expropriated page. + + + + + R1--3. + + For the CMO option: The platform must extend the + return code set for the hcall()s specified in + to include + H_NOT_ENOUGH_RESOURCES for cases where the function would cause more + memory to be I/O mapped than the caller is entitled to I/O map and the + platform is incapable of honoring the request. + + + + +
+ +
+ CMO I/O Mapping Extended Return Parameter + The syntax and semantics of the hcall()s in + are extended when the partition + is operating in CMO mode by returning in register R4 the change in the + partition’s total number of I/O mapped memory bytes due to the + execution of the hcall(). The number may be positive (increase in the + amount of memory mapped) negative or zero (the page was/remains mapped + for I/O access by another agent). + + + + R1--1. + + For the CMO option: The platform must extend the + syntax and semantics of the hcall()s specified in + when operating in CMO mode, to + return in register R4 the change to the total number of bytes that were + I/O mapped due to the hcall(). + + + +
+
+ +
+ H_SET_MPP + This hcall() sets, within limits, the partition’s memory + performance parameters. If the request parameter exceeds the constraint + of the calling LPAR’s environment, the hypervisor limits the value + set to the constrained value and returns H_Constrained. The memory weight + is architecturally constrained to be within the range of 0-255. + + + Syntax: + + + + + + + Semantics: + + + + Verify that the memory performance parameters specified are + within the constraints of the partition: + + + + If yes, atomically set the partition’s memory performance + parameters per the request and return H_Success. + + + + If not, set the partition’s memory performance parameters + as constrained by the partition’s configuration and return + H_Constrained. + + + + + + + + R1--1. + + For the CMO option: The platform must initially set + the partition memory performance parameters to their configured maximums + at partition boot time. + + + + + R1--2. + + For the CMO option: The platform must implement the + H_SET_MPP hcall() following the syntax and semantics of + . + + + + + R1--3. + + For the CMO option: The platform must constrain the + partition memory weight to the range 0-255. + + + + +
+ +
+ H_GET_MPP + This hcall() reports the partition’s memory performance + parameters. The returned parameters are packed into registers. + +
+ Command Overview + + + Syntax: + + + + + + + Semantics: + + + + Place the partition’s memory performance parameters for the + calling virtual processor’s partition into the respective + registers: + + + + R4: The number of bytes of main storage that the calling + partition is entitled to I/O map. In the case of a dedicated memory + partition this shall be the size of the partition’s logical address + space. + + + + R5: The number of bytes of main storage that the calling + partition has I/O mapped. In the case of a dedicated memory partition + this is not applicable which is represented by the code -1. + + + + R6: The calling partition’s virtual partition memory + aggregation identifier numbers, up to 4 levels: + + + + Bytes 0-1: Reserved for future aggregation definition, and set to + zero -- in the future this field may be given meaning. + + + + Bytes 2-3: Reserved for future aggregation definition, and set to + zero -- in the future this field may be given meaning. + + + + Bytes 4-5: 16 bit binary representation of the “Group + Number”. + + + + Bytes 6-7: 16 bit binary representation of the “Pool + Number”. In the case of a dedicated memory partition the + “Pool Number” is not applicable which is represented by the + code 0xFFFF. + + + + + + R7: Collection of short memory performance parameters for the + calling partition: + + + + Byte 0: Memory weight (0-255). In the case of a dedicated + processor partition this is not applicable which is represented by the + code 0. + + + + Byte 1: Unallocated memory weight for the calling + partition’s aggregation. + + + + Bytes 2-7: Unallocated I/O mapping entitlement for the calling + partition’s aggregation divided by 4096. + + + + + + R8: The calling partition’s memory pool main storage size + in bytes. In the case of a dedicated processor partition this is not + applicable which is represented by the code -1. + + + + R9: The signed difference between the number of bytes of logical + storage that are currently on loan from the calling partition and the + partition’s overage allotment (a positive number indicates a + request to the partition to loan the indicated number of bytes else they + will be expropriated as needed). + + + + R10: The number of bytes of main storage that is backing the + partition logical address space. In the case of a dedicated processor + partition this is the size of the partition’s logical address + space. + + + + Return H_Success. + + + + + + + + R1--1. + + For the CMO option: The platform must implement the + H_GET_MPP hcall() following the syntax and semantics of + . + + + + +
+ +
+ H_GET_MPP_X + This hcall() provides additional information over and above (not + duplication of) that which is returned by the H_GET_MPP hcall() + . The syntax of this hcall() is + specifically designed to be seamlessly extensible and version to version + compatible both from the view of the caller and the called on an + invocation by invocation basis. To this end, all return registers (R3 + (return code) through R10) are defined from the outset, some are defined + as reserved and are set to zero upon return by the hcall(). The caller is + explicitly prohibited from assuming that any reserved register contains + the value zero, so that there will be no incompatibility with future + versions of the hcall() that return non-zero values in those registers. + New definitions for returned values will define the value zero to + indicate a benign or unreported setting. + + + Syntax: + + + + + + + Semantics: + + + + Place the partition’s extended memory performance + parameters for the calling virtual processor’s partition into the + respective registers: + + + + R4: The number of bytes of the calling partition’s logical + real memory coalesced because they contained duplicated data. + + + + R5: If the calling partition is authorized to see pool wide + statistics (set by means that are beyond the scope of LoPAR) then The + number of bytes of logical real memory coalesced because they contained + duplicated data in the calling partition’s memory pool else set to + zero. + + + + R6:: If the calling partition is authorized to see pool wide + statistics (set by means that are beyond the scope of LoPAR) then PURR + cycles consumed to coalesce data else set to zero. + + + + R7: If the calling partition is authorized to see pool wide + statistics (set by means that are beyond the scope of LoPAR) then SPURR + cycles consumed to coalesce data else set to zero. + + + + R8: Reserved shall be set to zero - shall not be read by + the caller + + + + R9: Reserved shall be set to zero - shall not be read by + the caller + + + + R10: Reserved shall be set to zero - shall not be read by + the caller + + + + + + Return H_Success: + + + + + + R1--1. + + For the XCMO option: If the platform coalesces memory + pages that contain duplicated data it must implement the H_GET_MPP_X + hcall() following the syntax and semantics of + . + + + + + R1--2. + + For the XCMO option: the caller must be prepared for + H_GET_MPP_X to return H_Function or to have a return parameter that was + previously non-zero be consistently returned with the value zero if the + caller wishes to operate properly in a partition migration or fail-over + environment. + + + + +
+
+ +
+ Restoration Failure Interrupt + + + + R1--1. + + For the CMO option: When the platform experiences an + unrecoverable error restoring the association of a physical page with an + expropriated logical page following an attempted access of the + expropriated page by the partition, the platform must signal a Machine + Check Interrupt by returning to the partition’s interrupt vector at + location 0x0200. Note the subsequent firmware assisted NMI and check + exception processing returns a VPM SUE error log (See + ). + + + +
+ +
+ H_MO_PERF + This hcall() applies an artificial memory over-commitment to the + specified pool while monitoring the pool performance for overload, + removing the applied over-commitment if an overload trigger point is + reached. The overload trigger point is designed to double as a dead man + switch, eventually ending the over-commitment condition should the + experiment terminate ungracefully. Only the partition that is authorized + to run platform diagnostics is authorized to make this call. + + + Syntax: + + + + + + + Semantics: + This description is based upon the architectural model of + , and must be adjusted to + achieve the intent for the specific implementation. + + + + Validate that the caller has the required authority; else return + H_AUTHORITY. + + + + Validate that the pool parameter references an active memory pool + else; return H_Parameter. + + + + Raise the pool’s free list low water mark above its base + value by the signed amount in the mem parameter. (The result is + constrained to not less than the base low water mark value and no more + then the amount of memory in the pool.) + + + + Change the permissible pool memory low event counter by the + signed value of the lows parameter. + + + + Return in R4 the accumulated rise in the pool’s free list + low water mark above its base value. + + + + Return in R5 the current value of the permissible pool memory low + event counter. + + + + On each subsequent low memory event (page allocation where the + free list is at or below the low water mark), the permissible pool memory + low event counter is decremented. Should the counter ever reach zero, the + pool’s free list low water mark is returned to its base + value. + + + +
+ +
+ Expropriation/Subvention Notification Option + + The Expropriation/Subvention Notification Option (ESN) sub option + of the CMO option allows implementing platforms to notify supporting + OS’s of delays due to their access of an expropriated VPM page + (such as would be experienced during a “page in” operation). + With an expropriation notification, the OS may block the affected process + and dispatch another rather than having the platform block the virtual + processor that happened to be running the affected process. An + expropriation notification is paired with a subsequent subvention + notification signaled when the original access succeeds. Additionally new + page states allow the OS to indicate pages that it can restore itself, + thus relieving the platform from the burden of making copies of those + pages when they are expropriated and potentially side stepping the + “double paging problem” wherein the platform pages in a page + in response to a touch operation in preparation for an OS page in only to + have the OS immediately discard the page data without looking at + it. + The ESN option includes the following LoPAR extensions: + + + + Define augmented CMO page states + + + + Define the per partition Subvention Notification Structure + (SNS) + + + + Define H_REG_SNS hcall() to register the SNS + + + + Define Expropriation Notification field definitions within the + VPA + + + + Define expropriation and subvention event interrupts. + + + + + + R1--1. + + For the ESN option: The partition must be running + under the CMO option. + + + + + R1--2. + + For the ESN option: The platform must ignore/disable + all other ESN option functions and features unless the OS has + successfully registered the Subvention Notification Structure via the + H_REG_SNS hcall. See + for details. + + + + +
+ ESN Augmentation of CMO Page Usage States + The ESN option augments the set of page states defined by the CMO + option that are set by the cooperating OS using the flags parameter of + the HPT hcall()s. The platform uses these page states to estimate the + overhead associated with expropriating the specific page. + + Active- An Expropriation notification on this + type of page allows the OS to put the using process to sleep, until the + page is restored, as signaled by a corresponding subvention notification, + at which time the affected instruction is retried. + + Expendable- the page retains data that the OS + can regenerate, for example, a text page that is backed up on disk; + usually the page is mapped read only. A reflected expropriation + notification on this type of page requires the OS to restore the page + - thus the platform presents somewhat different interrupt status + from that used by an Active page. + Expropriating an “Expendable” page should result in + lower overhead than expropriating an “Active” page since + the contents need not be paged out before the page is reused. + + An Expendable page that is Bolted while not illegal has to be + treated as an “Active” page since an access to a Bolted + page may not result in an expropriation notification. + + + Latent- the page contains data that the OS can + regenerate unless the contents have been modified - at which time + the page state appears to be “Active”, this is similar to + “Expendable” for pages mapped read/write. For example, a page + of a mapped file. Expropriation Notification is like “Active” + or “Expendable” above. + + Loaned- When the OS does access the page, it + is likely that the access will result in an expropriation + notification + + + ESN Augmentation of CMO Page Usage State flags + Definition + + + + + + + + + + + Flag bit 28 + + + + + Flag bits 29 - 30 + + + + + Flag bit 31 + + + + + Comments + + + + + + + + 1 + + + 01 + + + 0 + + + Set page state to Latent + Note: If Expropriation Notification is disabled, or the + bolted bit (HPT bit 59) is set to 1, the page state to Active + (Active Critical if flag bit 31=1). + + + + + + 01 + + + 1 + + + Set page State to Latent Critical + + + + + 10 + + + 0 + + + Set page state to Expendable + + + + + 10 + + + 1 + + + Set page state to Expendable Critical + + + + +
+
+ +
+ Expropriation Notification + Under the ESN option, notice of an attempt to access an + expropriated page is given when the Expropriation Interrupt is enabled in + the virtual processor VPA. Additionally the virtual processor VPA + Expropriation Correlation Number and Expropriation Flags fields are set + to allow the affected program to determine when the access may succeed + and if the program needs to restore data to the Subvened page, see + details in + . Once the VPA has been + updated, the platform presents an Expropriation Fault interrupt to the + affected virtual processor see details in + . + +
+ ESN VPA Fields + + + + R1--1. + + For the ESN + option: The platform must support the VPA field definitions of + , + , and + . + + + + + + VPA Byte Offset 0xB9 + + + + + + + + + + + + + + + + 0 + + + + + 1 + + + + + 2 + + + + + 3 + + + + + 4 + + + + + 5 + + + + + 6 + + + + + 7 + + + + + Bit Number + + + + + + + + Reserved (0) + + +   + + + 0 + + + Dedicated processor cycle donation inhibited + + + + +   + + + 1 + + + Dedicated processor cycle donation enabled + + + + + 0 + + +   + + + Expropriation interrupt disabled + + + + + 1 + + +   + + + Expropriation interrupt enabled + + + + +
+   + + Firmware Written VPA Starting at Byte Offset + 0x178 + + + + + + + + + + + + + + 0x178 F + + + + + 0x179 + + + + + 0x17A + + + + + 0x17B + + + + + 0x17C + + + + + 0x17D + + + + + 0x17E + + + + + 0x17 + + + + + + + + Reserved for firmware locks + + + Reserved + + +   + + + Expropriation Correlation + Number Field + + + + + Expropriation Flags -- See + . + + + + +
+ + Note: The Expropriation Flags and Expropriation + Correlation Number Fields are volatile with respect to Expropriation + Notifications thus it should be saved by the OS before executing any + instruction that may access unbolted pages. + + + Expropriation Flags at VPA Byte Offset 0x17D + + + + + + + + + + + + + + + + 0 + + + + + 1 + + + + + 2 + + + + + 3 + + + + + 4 + + + + + 5 + + + + + 6 + + + + + 7 + + + + + Bit Number + + + + + + + + Reserved (0) + + + 0 + + + The Subvened page data is/will be zero + + + + + 1 + + + The Subvened page data will be restored. + + + + +
+
+ +
+ Expropriation Interrupt + When the platform is running with real memory over-commitment, + eventually a partition virtual processor will access a stolen page. The + transparent solution is to block the virtual processor until the platform + has restored the page. By enabling the Expropriation Interrupt via the + Expropriation Interrupt Enable field of the VPA (see + ) the cooperating OS indicates + that it is prepared to make use of its virtual processors for other + purposes during the page restoration and/or restore the contents of + “expendable” and unmodified “latent” + pages. + + + + R1--1. + + For the ESN option: When the partition accesses an + expropriated page and either the page was bolted (PTE bit 59=1) or the + Expropriation Interrupt Enable bit of the affected virtual + processor’s VPA is off see + , then the platform must + recover the page transparently without an Expropriation Interrupt. + + + + + R1--2. + + For the ESN option: + When the partition accesses an expropriated page and the summation of the + partition’s in use subvention event queue entries plus outstanding + subvention events is equal to or greater than the size of the + partition’s subvention event queue, the platform must recover the + page prior to issuing any associated Expropriation Interrupt. + + Note: Requirement + prevents the overflow of the + subvention queue. + + + + + R1--3. + + For the ESN option: When the partition accesses an + expropriated “Unused” or “Expendable” page, the + platform must, unless prevented by + , set bit 7 of the affected + processor’s Expropriation Flags VPA byte (see + ) to 0b0; else the platform + must set the bit to 0b1. + + + + + R1--4. + + For the ESN option: When the partition accesses an + expropriated page and the platform associates a physical page with the + logical page prior to returning control to the affected virtual + processor, the platform must, unless prevented by + , set the Expropriation + Correlation Number field of the affected virtual processor’s VPA to + 0x0000 (see + ). + + + + + R1--5. + + For the ESN option: When the partition accesses an + expropriated page, the platform is not prevented by + , does not associate a physical + page with the logical page prior to returning control to the affected + virtual processor, and the restoration of the logical page has NOT + previously been reported to the OS with an expropriation notification, + the platform must, set the Expropriation Correlation Number field of the + VPA to a non-zero unique value for all outstanding recovering pages for + the affected partition. + + + + + R1--6. + + For the ESN option: When the partition accesses an + expropriated page, the platform is not prevented by + , does not associate a physical + page with the logical page prior to returning control to the affected + virtual processor, and the restoration of the logical page has previously + been reported to the OS with an expropriation notification, the platform + must set the Expropriation Correlation Number field of the VPA to the + same value as was supplied with the previous expropriation notification + event associated with the outstanding recovering page for the affected + partition. + + + + + R1--7. + + For the ESN option: When the partition performs an + instruction fetch from an expropriated page, the platform must, unless + prevented by + , signal the affected virtual + processor with an Expropriation Interrupt by returning to the affected + virtual processor’s interrupt vector at location 0x0400 with the + processor’s MSR, SRR0 and SRR1 registers set as if the instruction + fetch had experienced a translation fault type of Instruction Storage + Interrupt except that SRR1 bit 46 (Trap) is set to a one. + + + + + R1--8. + + For the ESN option: When the partition performs a + load or store instruction that accesses an expropriated page, the + platform must, unless prevented by + , signal the affected virtual + processor with an Expropriation Interrupt by returning to the affected + virtual processor’s interrupt vector at location 0x0300 with the + processor’s MSR, DSISR, DAR, SRR0 and SRR1 registers set as if the + storage access had experienced a translation fault type of Data Storage + Interrupt except that SRR1 bit 46 (Trap) is set to a one. + + + + +
+
+ +
+ ESN Subvention Event Notification + ESN uses an event queue within the Subvention Notification + Structure (SNS) to notify the OS of page subvention operations. + Subvention events have a two byte SNS-EQ entry which has the value of the + expropriation correlation number from the associated expropriation + notification event + + + + R1--1. + + For the ESN option: The platform must implement the + structures, syntax and semantics described in + , + , and + . + + + + + +
+ SNS Memory Area + + + + R1--1. + + For the ESN option: The platform + must support the 4K byte aligned SNS not spanning its page boundary + defined by + . + + + + + + Subvention Notification Structure + + + + + + + + + + + Access + + + + + Offset + + + + + Usage + + + + + + + + Written by OS Read by Hypervisor + + + 0x00 + + + Bit + + + Notification Control + + + + + 0 + + + Notification Trigger + + + + + 1-7 + + + Reserved + + + + + Written by Hypervisor Read by OS + + + 0x01 + + + Bit + + + Event Queue State + + + + + 0 + + + 0 = Operational + 1 = Overflow + + + + + 1-7 + + + Reserved + + + + + Set to non-zero by Hypervisor Read and cleared to zero by + OS + + + 0x02-0x02 + + + First SNS EQ Entry + + + + + . + . + . + + + + + (SNS Length -2) - SNS Length - 1) + + + Last SNS EQ Entry + + + + +
+
+ +
+ SNS Registration (H_REG_SNS) + + + Syntax: + + + + + + + Semantics: + + + + If the Address parameter is -1 then deregister any previously + registered SNS for the partition, disable ESN functions and return + H_Success. (Care is required on the part of the OS not to create any + Restoration Paradox Failures prior to registering a new SNS. See + for details.) + + + + If the Shared Logical Resource option is implemented and the + Address parameter represents a shared logical resource that has been + rescinded, then return H_RESCINDED. + + + + If the Address parameter is not 4K aligned in the valid logical + address space of the caller, then return H_Parameter. + + + + If the Length parameter is less than 256 or the Address plus + Length spans the page boundary of the page containing the starting + logical address, then return H_P2. + + + + Register the SNS structure for the calling partition by saving + the partition specific information: + + + + Record the SNS starting address + + + + Record the SNS ending address + + + + Record the next EQ entry to fill address (SNS starting address + +2) + + + + Set the SNS interrupt toggle = SNS Notification Trigger + + + + Set the SNS Event Queue State to “Operational” + + + + + + + + Return: + + + + R3: H_Success + + + + R4: Value to be passed in the “unit address” + parameter of the H_VIO_SIGNAL hcall() to enable/disable the virtual + interrupt associated with the transition of the SNS from empty to + non-empty. + + + + R5: Interrupt source number associated with the SNS empty to + non-empty virtual interrupt. + + + + +
+ +
+ SNS Event Processing + The following sequence is used by the platform to post an SNS + event. The SNS-EQ used corresponds to the EEN event type. This sequence + refers to fields described in + . + + + + If the SNS EQ overflow state is set, exit. + /* An EQ overflow drops all new events until software recovers the + EQ*/ + + + + Using atomic update protocol, store the event identifier into + the location indicated by the SNS next EQ entry to fill pointer if the + original contents of the location were zero; else set the associated EQ + overflow state and exit. + /* The value of zero is reserved for an unused entry -- an EQ + overflow drops the new event */ + + + + Increment the SNS next EQ entry to fill pointer by the size of + the EQ entry (2) modulo the size of the EQ + /* Adjust fill pointer */ + + + + If the SNS interrupt toggle = SNS Notification Trigger then + exit. + /* Exit on no event queue transition */ + + + + Invert the SNS interrupt toggle. + /* Remember event queue transition */ + + + + If the SNS interrupt is enabled, signal a virtual interrupt to + the associated partition. + /* Signal transition when enabled */ + + +
+ +
+ ESN Interrupts + The ESN option may generate several interrupts to the partition OS. + Defined in this section are those in addition to the Expropriation + Notification interrupts defined above. + +
+ Subvention Notification Queue Transition + Interrupt + + + + R1--1. + + For the ESN option: When the + platform has restored the association of a physical page with the logical + page that caused an Expropriation Notification interrupt with a non-zero + Expropriation Correlation Number, the platform must post the + corresponding Expropriation Correlation Number to the Subvention Event + Queue see + . + + + +
+ +
+ Restoration Paradox Failure + Restoration Paradox Failures result in an unrecoverable memory + failure machine check. + + + + R1--1. + + For the ESN option: When the platform finds that + Expropriation Notification has been disabled after it has discarded the + contents of an “Expendable” page, it must treat any access to + such a page as an unrecoverable error restoring the association of a + physical page with the expropriated logical page. + + + +
+
+
+
+
+ +
+ Virtual Partition Memory Pool Statistics Function + Set + The hcall-vpm-pstat function set may be configured via the + partition definition in none or any number of partitions as the VPM + administrative policy dictates. + +
+ H_VPM_PSTAT + This hcall() returns statistics on the physical shared memory pool. + Since these statistics can be manipulated by the processing of a single + partition, there is a risk of creating a covert channel through this + call. To mitigate this risk, the call is contained in a separate function + set that can be protected by authorization methods outside the scope of + LoPAR. + + + Syntax: + + + + + + + Parameters: + + + + Input: None + + + + Output: + + + + R4: Total VM Pool Page Faults + + + + R5: Total Page Fault Wait Time (Time Base Ticks) + + + + R7: Total Pool Physical Memory + + + + R8: Total Pool Physical Memory that is I/O mapped + + + + R9: Total Logical Real Memory that is Virtualized by the VM + Pool + + + + + + + + Semantics: + + + + Verify that calling partition has the authority to make the call + else return H_Authority. + + + + Report the statistics for the memory pool used to instantiate the + virtual real memory of the calling partition. + + + + Place in R4 the summation of the virtual partition memory page + faults against the memory pool since the initialization of the + pool. + + + + Place in R5 the summation of timebase ticks spent waiting for the + page faults indicated in R4. + + + + Place in R6 the total amount of physical memory in the memory + pool. + + + + Place in R7 the summation of the entitlement of all active + partitions served by the memory pool. + + + + Place in R8 the summation of the I/O mapped memory of all active + partition served by the memory pool. + + + + Place in R9 the summation of the logical real memory of all + active partitions served by the memory pool. + + + + + + Return H_Success. + + + +
+
+
+ +
+ Logical Partition Control Modes + Selected logical partition control modes may be modified by the + client program. + +
+ Secondary Page Table Entry Group (PTEG) Search + The page table search algorithm, described by the + , consists of searching for a + Page Table Entry (PTE) in up to two PTEGs. The first PTEG searched is the + “primary PTEG”. If a PTE match does not occur in the primary + PTEG, the hardware may search the “secondary PTEG”. If a PTE + match is not found in the searched PTEGs, the hardware signals a + translation exception. + Code is not required to place any PTEs in secondary PTEGs. + Therefore, if a PTE match does not occur in a primary PTEG there is no + need for the hardware to search a secondary PTEG to determine that a + search has failed. The “Secondary Page Table Entry Group” bit + of + “ibm,client-architecture-support” allows + code to indicate that there is no need to search secondary PTEGs to + determine that a PTE search has failed. +
+
+ +
+ Partition Energy Management Option (PEM) + This section describes the functional interfaces that are available + to assist the partition Operating System optimize trade offs between energy + consumption and performance requirements. + +
+ Long Term Processor Cede + To enable the hypervisor to effectively reduce the power draw from + unused partition processors, the concept of cede wakeup latency is + introduced with the Partition Energy Management Option. A one byte cede + latency specifier VPA field communicates the maximum latency class that + the OS can tolerate on wakeup from H_CEDE. In general the longer the + wakeup latency the greater the savings that can be made in power drawn by + the processor during a cede operation. However, due to implementation + restrictions, the platform might be unable to take full advantage of the + latency that the OS can tolerate thus the cede latency specifier is + considered a hint to the platform rather than a command. The platform may + not exceed the latency state specified by the OS. Calling H_CEDE + , with value of the cede + latency specifier set to zero denotes classic H_CEDE behavior. Calling + H_CEDE with the value of the cede latency specifier set greater than zero + allows the processor timer facility to be disabled (so as not to cause + gratuitous wake-ups - the use of H_PROD, or other external + interrupt is required to wake the processor in this case). An External + interrupt might not awake the ceded process at some of the higher (above + the value 1) cede latency specifier settings. Platforms that implement + cede latency specifier settings greater than the value of 1 implement the + cede latency settings system parameter see + . The hypervisor is then free to take energy + management actions with this hint in mind. + + + + R1--1. + + For the PEM option: The platform must honor the OS + set cede latency specifier value per the definition of + . + + + + + R1--2. + + For the PEM option: The platform must map any OS set + cede latency specifier value into one of its implemented values that does + not exceed the latency class set by the OS. + + + + + R1--3. + + For the PEM option: The platform must implement the + cede latency specifier values of 0 and 1 per + . + + + + + R1--4. + + For the PEM option: If the platform implements cede + latency specifier values greater than 1 it must implement the cede + latency settings values sequentially without holes. + + + + + R1--5. + + For the PEM option: If the platform implements cede + latency specifier values greater than 1 each sequential cede latency + settings value must represent a cede wake up latency not less than its + predecessor, and no less restrictive than its predecessor. + + + + + R1--6. + + For the PEM option: If the platform implements cede + latency specifier values greater than 1 it must implement the cede + latency settings system parameter see + . + + + +
+ +
+ H_GET_EM_PARMS + This hcall() returns the partition’s energy management + parameters. The return parameters are packed into registers. + Programming Note: On platforms that implement the + partition migration option, after partition migration: + + + + The support for this hcall() might change, the caller should be + prepared to receive an H_Function return code indicating the platform + does not implement this hcall(). + + + + Fields that were defined as “reserved” might contain + data; calling code should be tested to ensure that it ignores fields + defined as “reserved” at the time of its design, and that it + operates properly when encountering “zeroed” defined fields + that indicate that the field does not contain useful data. + + + + + Implementation Note: To aid the testing of calling + code, implementations would do well to include debug tools that seed + reserved return fields with random data. + + + Syntax: + + + + + + + Parameters: (on return) + + + + + + + + + + + +   + + + + + + + + + + + + + + Status Codes (bit offset within 2 byte field): Bits 0:5 Reserved + (zero) + + + + Bits 6:8 Energy Management major code: + + + + 0b000: Non - floor modes: + + + + Bits 9:15 Energy Management minor code: + + + + + 0x00: The energy management policy for this aggregation level is + not specified. + + + + 0x01: Maximum Performance (Energy Management enabled - + performance may exceed nominal) + + + + 0x02: Nominal Performance (Energy Management Disabled) + + + + 0x03: Static Power Saving Mode + + + + 0x04: Deterministic Performance (Energy Management enabled + - consistent performance on a given workload independent of + environmental factors and component variances) + + + + 0x05 - 0x7F Reserved + + + + + + + + 0b001: Dynamic Power Management: + + + + Bits 9:15 Performance floor as a percentage of nominal (0% - + 100%). + + + + + + 0b010:0b111 Reserved + + + + + + Implementation Note: Status Code Fields are + determined by means outside the scope of LoPAR. Platform designs may + define a hierarchy of aggregations in which lower levels by default + inherit the energy management policy of their parent. + + + + + + + + + + + + + + + Bytes 0:3 four byte Power Draw Status/Limit for the + platform + + + + Bit 0: Power Draw Limit is hard/soft: 0 = Soft, 1 = Hard + + + + Bits 1:7 Reserved. + + + + Bits 8:31 unsigned binary Power Draw Limit times 0.1 watts + + + + + + + + + + + + + + + +   + + + + + + + + + + + + + + The total processor energy consumed by the calling partition + since boot in Joules times 2**-16. The value zero indicates that the + platform does not support reporting this parameter. + + + + + + + + + + + + + + + + + The total memory energy consumed by the calling partition since + boot in Joules times 2**-16. The value zero indicates that the platform + does not support reporting this parameter. + + + + + + + + + + + + + + + + + The total I/O energy consumed by the calling partition since boot + in Joules times 2**-16. The value zero indicates that the platform does + not support reporting this parameter. + + + + + + Semantics: + + + + Place the partition’s performance parameters for the + calling virtual processor’s partition into the respective + registers: + + + + R4: Energy Management Status Codes + + + + R5: Power Draw Limits (Platform and Group) + + + + R6: Power Draw Limits (Pool and Partition) + + + + R7: Partition Processor Energy Consumption + + + + R8: Partition Memory Energy Consumption + + + + R9: Partition I/O Energy Consumption + + + + + + Return H_Success. + + + + + + R1--1. + + For the PEM option: The platform must implement the + H_GET_EMP hcall() following the syntax and semantics of + . + + + + +
+ +
+ H_BEST_ENERGY + This hcall() returns a hint to the caller as to the probable impact + toward the goal of minimal platform energy consumption for a given level + of computing capacity that would result from releasing or activating + various computing resources. The returned value is a unitless priority, + the lower the returned value; the more likely the goal will be achieved. + The accuracy of the returned hint is implementation dependent, and is + subject to change based upon actions of other partitions; thus the + implementation can only provide a “best effort” to be + “substantially correct”. Implementation dependent support for + this hcall() and supported resource codes might change during partition + suspension as in partition hibernation or migration; the client program + should be coded to gracefully handle H_Function, H_UNSUPPORTED, and + H_UNSUPPORTED_FLAG return codes. + H_BEST_ENERGY may be used in one of two modes, + “inquiry” or “ordered” specified by the setting + of bit 54 of the eflags parameter. It is intended that ordered mode be + used when the client program is largely indifferent to the specific + resource instance to be released or activated. In ordered mode, + H_BEST_ENERGY returns a list of resource instances in the order from the + best toward worst to choose to release/activate to achieve minimal energy + consumption starting with an initial resource instance in the ordered + list (if the specified initial resource is the reserved value zero the + returned list starts with the resource having the greatest probability of + minimizing energy consumption). It is intended that inquiry mode be used + when the client program wishes to compare the energy advantage of making + a resource selection from among a set of candidate resource instances. In + inquiry mode, H_BEST_ENERGY returns the unitless priority of + releasing/acquiring each of the specified resource instances. It is + expected that in the vast majority of cases, the client code will receive + data on a sufficient number of resource instances in one H_BEST_ENERGY + call to make its activate/release decision; however, in those rare cases + where more information is needed, a series of H_BEST_ENERGY calls can be + made to accumulate information on an arbitrary number of computing + resource instances. + Platforms may optionally support “buffered ordered” + return data mode. If the platform supports “buffered ordered” + return data mode, a “b” suffix appears at the end of the list + that terminates the hcall-best-energy-1 function set entry. If the + “buffered ordered” return data mode is supported the caller + may specify the “B” bit in the eflags parameter and supply in + P3 the logical address of a 4K byte aligned return buffer. + The probable effects of a given resource instance selection might + vary depending upon the intention of the client program to take other + actions. These other actions include the ability to reactivate a released + resource within a given time latency and number of resources the client + program intends to activate/release as a group. The eflags parameter to + H_BEST_ENERGY contains fields that convey hints to the platform of the + client program intentions in these areas; implementations might take + these hints into consideration as appropriate. The high order four (4) + bytes of the eflags parameter contain the unsigned required reactivation + latency in time base ticks (the reserved value of all zeros indicates an + unspecified reactivation latency). + Calling H_BEST_ENERGY with the eflags “refresh” flag + (bit 54) equal to a one causes the hypervisor to compute the relative + unitless priority value (1 being the best to activate/release with + increasing numbers being poorer choices from the perspective of potential + energy savings) for each instance of the specified resource that is owned + by the calling partition. If the hypervisor can not distinguish a + substantially different estimate for the various resource instances the + call returns H_Not_Available. If the “refresh” flag is equal + to a zero, the list as previously computed is used. Care should be + exercised when using the non-refresh version to ensure that the state of + the partition’s owned resource list has been initialized at some + point and has not changed due to resource instance activation/release + (including dynamic reconfiguration) activities by other partition threads + else the results of the H_BEST_ENERGY call are unpredictable (ranging + from inaccurate prediction values up to and including error code + responses). + The return values for H_BEST_ENERGY are passed in registers. + Following standard convention, the return code is in R3. Register R4 + contains the response count. If the call is made in “inquiry” + mode the response count equals the number of non-zero requested resource + instance entries in the call. If the call is made in + “ordered” mode, the response count contains the number of + entries in the ordered list from the first entry returned until the worst + choice entry. If the response count is <= 8 (512 for ordered buffer + mode) then the response count also indicates how many resource instances + are being reported by this call, if the response count is >8 (512 for + ordered buffer mode) then this call reports eight (512 for ordered buffer + mode) resource instances. Each response consists of three fields: bytes 0 + -- 2 are reserved, byte 3 contains the unitless priority for selecting + the indicated resource instance, and bytes 4 -- 7 contain the resource + instance identifier value corresponding to that passed in the + “ibm,my-drc-index” property. + In order to represent more accurately the significance of certain + priority values relative to others, the platform might leave holes in the + ranges of reported priority values. As an example there may be a gap of + several priority numbers between the value associated with a resource + that can be powered down versus one that can only be placed in an + intermediate energy mode, and yet again another gap to a resource that + represents a necessary but not sufficient condition for reducing energy + consumption. + + + Syntax: + + + + + + + Parameters: (on entry) + + + + + + + + + + + +   + + + + + + + + + + +   + + + + + + + + + + + + + + (on return) + + + R3: Return code + + + R4: Response Count Value <8 indicate the number of returned + values in registers starting with R5. The contents of registers after the + last returned value as indicated by the Response Count Value are + undefined. + + + R5 -- R12 Bytes 0-2 Reserved + + + Byte 3: 1 - 255 -- unitless priority value relative to + lowest total energy consumption for selecting the corresponding resource + ID. + + + Bytes 4-7 Resource instance ID to be used as input to dynamic + reconfiguration RTAS calls as would the value presented in the + “ibm,my-drc-index” property. + + + + + + Semantics: + + + + If the resource code in the eflags parameter is not supported + return H_UNSUPPORTED + + + + If other binary eflags values are not valid then return + H_UNSUPPORTED_FLAG with the specific value being (-256 - the bit + position of the highest order unsupported bit that is a one); + + + + If the eflags parameter “refresh” bit is zero and the + list has not been refreshed since the last return of H_Not_Available then + return H_Not_Available. + + + + If the eflags parameter “refresh” bit is a one + then: + + + + If energy estimates for the partition owned resources are + substantially indistinguishable then return H_Not_Available. + + + + Assign a priority value to each resource of the type specified in + the resource code owned by the calling partition relative to the probable + effect that selecting the specified resource to activate/release (per + eflags code) within the specified latency requirements would have on + achieving minimal platform energy consumption. (1 being the best + increasing values being worse - implementations may choose to use + an implementation dependent subset of the available values) + + + + Order the specified resources owned by the calling partition + starting with those having a priority value of 1; setting the resource + pointer to reference that starting resource. + + + + + + If the eflags parameter bit 54 is a one (“ordered”) + then + + + + If P2 == 0 then set pointer to best resource in ordered + list + + + + Else + + + + If P2 <> the drc-index of one of the resources in the + ordered list then return H_P2 + + + + Else set pointer to the resource corresponding to P2 + + + + + + Set R4 to the number of resources in the ordered list from the + pointer to the end + + + + If eflags “B” bit == 0b0 then /* this assumes that + the ordered buffer option is supported */: + + + + If R4 > 8 set count to 8 else set count to R4 + + + + Load “count” registers starting with R5 with the + priority value and resource IDs of the “count” resource + instances from the ordered list starting with the resource instance + referenced by “pointer”. + + + + + + Else + + + + If P3 does not contain the 4K aligned logical address of a + calling partition memory page then return H_P3 + + + + If R4 > 512 set count to 512 else set count to R4 + + + + Load “count” 8 byte memory fields starting with + logical address in R3 with the priority value and resource IDs of the + “count” resource instances from the ordered list starting + with the resource instance referenced by “pointer”. + + + + + + Return H_SUCCESS + + + + + + Else /* “inquiry” mode */ + + + + Set R4 to zero + + + + For each input parameter P2 -- P9 or until the input parameter is + zero + + + + If the input parameter Px <> the drc-index of one of the + resources in the ordered list then return H_Px + + + + Fill in byte 3 of the register containing Px with the priority + value of the resource instance corresponding to the drc-index (bytes 4 -- + 7) of the register. + + + + Increment R4 + + + + + + Return H_SUCCESS + + + + + + + + R1--1. + + For the PEM option: The platform must implement the + H_BEST_ENERGY hcall() following the syntax and semantics of + . + + + + +
+
+ +
+ Platform Facilities + This section documents the hypervisor interfaces to optional platform + facilities such as special purpose coprocessors. + +
+ H_RANDOM + If the platform supports a random number generator platform + facility the + “ibm,hypertasfunctions” property of the + /rtas node contains the function set specification + “hcall-random” and the following hcall() is supported. + + + +
+ +
+ Co-Processor Facilities + If the platform supports a co-processor platform facility the + “ibm,hypertas-functions” property of the + /rtas node contains + the function set specification “hcall-cop” and the following + hcall()s are supported. + For asynchronous coprocessor operations the caller may either + specify an interrupt source number to signal at completion or the caller + may poll the completion code in the CSB. The hypervisor and caller need + to take into account the processor storage models with explicit memory + synchronization to ensure that the rest of the return data from the + operation is visible prior to setting the CSB completion code, and that + any operation data that might have been fetched prior to the setting of + the CSB completion code is discarded. + Note: The H_MIGRATE_DMA hcall() does not handle data pages subject + to co-processor access, it is the caller’s responsibility to make + sure that outstanding co-processor operations do not target pages that + are being migrated by H_MIGRATE_DMA. + +
+ H_COP_OP: + The architectural intent of this hcall() is to initiate a + co-processor operation. Co-processor operations may complete with either + synchronous or asynchronous notification. In synchronous notification, + all platform resources associated with the operation are allocated and + released between the call to H_COP_OP and the subsequent return. In + asynchronous notification, operation associated platform resources may + remain allocated after the return from H_COP_OP, but are subsequently + recovered prior to setting the completion code in the CSB. For the + partition migration option no asynchronous notification operation may be + outstanding at the time the partition is suspended. + + + + + Syntax: + + + + Flags: + + + + Reserved (bits 0-- 38) + + + + “Rc” (bit 39) On Asymmetric Encryption operations the + “Rc” bit indicates that the high order 16 bits of the + “in” parameter contain the “Rc” field specifying + the encoded operand length while the remainder of the “in” + and “inlen” parameter bits are reserved and should be + 0b0 + + + + Notification of Operation (bits 40-- 41): + + + + 00 Synchronous: In this mode the hypervisor synchronously waits + for the coprocessor operation to complete. To preserve Interrupt service + times of the caller and quality of service for other callers, the length + of synchronous operations is restricted (see inlen parameter). + + + + 01 Reserved + + + + 10 Asynchronous: In this mode the hypervisor starts the + coprocessor operation and returns to the caller. The caller may poll for + operation completion in the CSB. + + + + 11 Async Notify: In this mode the hypervisor starts the + coprocessor operation as with the Asynchronous notification above however + the operation is flagged to generate a completion interrupt to the + interrupt source number given in the + “ibm,copint” property. When the interrupt + is signaled the caller may check the operation completion status in the + CSB. + + + + + + Interrupt descriptor index for Async Notify (bits 42-- 55) + + + + FC field: The FC field is the co-processor name specific function + code (bits 56-- 63) + + + + + + Resource identifier (bits 32-- 63(as from the + “ibm,resource-id” property)) + + + + in/inlen and out/outlen parameters: + + + + If the *len parameter is non-negative; the respective in/out + parameter is the logical real address of the start of the respective + buffer. The starting address plus the associated length may not extend + beyond the bounds of a 4K page owned by the calling partition. For + synchronous notification operations, the parameter values may not exceed + an implementation specified maximum; in some cases these are communicated + by the values of the + “ibm,maxsync-cop” property of the device + tree node that represents the co-processor to the partition. + + + + If the *len parameter is negative; the respective in/out + parameter is the logical real address of the start of a scatter/gather + list that describes the buffer with a length equal to the absolute value + of the *len parameter. The starting address of the scatter/gather list + plus the associated length may not extend beyond the bounds of a 4K page + owned by the calling partition. Further the scatter/gather list shall be + a multiple of 16 bytes in length not to exceed the value of the + “ibm,max-sg-len” property of the device tree + node that represents the coprocessor to the partition. Each 16 byte entry + in the scatter gather list consists of an 8 byte logical real address of + the start of the respective buffer segment. The starting address plus the + associated length may not extend beyond the bounds of a 4K page owned by + the calling partition. For synchronous notification operations, the + summation of the buffer segment lengths for the in scatter/gather list + may be limited; in some cases these limitations are communicated by the + value of the + “ibm,max-sync-cop” property of the device + tree node that represents the coprocessor to the partition. + + + + + + csbcpb: logical real address of the 4K naturally aligned memory + block used to house the co-processor status block and FC field dependent + co-processor parameter block. + + + + Output parameters on return + + + + R3 contains the standard hcall() return code: if the return code + is H_Success then the contents of the 4K naturally aligned page specified + by the csbspb parameter are filled from the hypervisor csb and cpb with + addresses converted from real to calling partition logical real + + + + + + + + Semantics: + + + + The hypervisor checks that the resource identifier parameter is + valid for the calling partition else returns H_RH_PARM. + + + + The hypervisor checks that for the coprocessor type specified by + the validated resource identifier parameter there are no non-zero + reserved bits within the function expansion field of the flags parameter + else returns H_UNSUPPORTED_FLAG for the highest order non-zero + unsupported flag. + + + + If the operation notification is asynchronous, check that there + are sufficient resources to initiate and track the operation else return + H_Resource. + + + + The hypervisor checks that the flag parameter notification field + is not a reserved value and FC field is valid for the specified + coprocessor type else returns H_ST_PARM + + + + If the notification field is “synchronous” the + hypervisor checks that the FC field is valid for synchronous operations + else return H_OP_MODE. + + + + The hypervisor builds the CRB CCW field per the coprocessor type + specified by the validated resource identifier parameter and by copying + the coprocessor type defined number of FC field bits from the low order + flags parameter FC field to the corresponding low order bits of CCW byte + 3. + + + + If the resource ID is an asymmetric encryption then (If the Flags + Parameter “Rc” bit is on then check the High order 16 bits of + the “in” parameter for a valid “Rc” encoding and + transfer to the CRB starting at byte 16 else return H_P2) else Validate + the inlen/in parameters and build the source DDE + + + + Verify that the “in” parameter represents a valid + logical real address within the caller’s partition else return + H_P2 + + + + If the “inlen” parameter is non-negative: + + + + Verify that the logical real address of (in + inlen) is a valid + logical real address within the same 4K page as the “in” + parameter else return H_P3. + + + + If the operation notification is synchronous verify that the + combination of parameter values request a sufficiently short operation + for synchronous operation else return H_TOO_BIG. + + + + + + If the “inlen” parameter is negative: + + + + Verify that the absolute value of inlen meet all of the follow + else return H_P3: + + + + Is <= the value of + “ibm,max-sg-len” + + + + Is an even multiple of 16 + + + + That in + the absolute value of inlen represents a valid logical + real address within the same 4K caller partition page as the in + parameter. + + + + + + Verify that each 16 byte scatter gather list entry meets all of + the following else return H_SG_LIST: + + + + Verify that the first 8 bytes represents a valid logical real + address within the caller’s partition. + + + + Verify that the logical real address represented by the sum of + the first 8 bytes and the second 8 bytes is a valid logical real address + within the same 4K byte page as the first 8 bytes. + + + + + + If the operation notification is synchronous verify that the sum + of all the scatter gather length fields (second 8 bytes of each 16 byte + entry) request a sufficiently short operation for synchronous operation + else return H_TOO_BIG. + + + + + + For the Shared Logical Resource Option if any of the memory + represented by the in/inlen parameters have been rescinded then return + H_RESCINDED. + + + + Fill in the source DDE list from the converted the in/inlen + parameters. + + + + + + Validate the outlen/out parameters and build the target + DDE + + + + Verify that the “out” parameter represents a valid + logical real address within the caller’s partition else return + H_P4 + + + + If the “outlen” parameter is non-negative verify that + the logical real address of (out + outlen) is a valid logical real + address within the same 4K page as the “out” parameter else + return H_P5. + + + + If the “outlen” parameter is negative: + + + + Verify that the absolute value of outlen meet all of the follow + else return H_P5: + + + + Is <= the value of + “ibm,max-sg-len” + + + + Is an even multiple of 16 + + + + That out + the absolute value of outlen represents a valid + logical real address within the same 4K caller partition page as the out + parameter + + + + + + Verify that each 16 byte scatter gather list entry meets all of + the following else return H_SG_LIST: + + + + Verify that the first 8 bytes represents a valid logical real + address within the caller’s partition. + + + + Verify that the logical real address represented by the sum of + the first 8 bytes and the second 8 bytes is a valid logical real address + within the same 4K page as the first 8 bytes. + + + + + + + + For the Shared Logical Resource Option if any of the memory + represented by the out/outlen parameters have been rescinded then return + H_RESCINDED. + + + + Fill in the destination DDE list from the converted the + out/outlen parameters. + + + + + + If the operation notification is asynchronous then verify that + the input and output buffers do not overlap else return H_OVERLAP (makes + the operations transparently restartable) + + + + Check that the csbcpb parameter is page aligned within the + calling address space of the calling partition else return H_P6 + + + + If the operation specifies a CPB and the specified CPB is invalid + for the operation then return H_ST_PARM. + + + + Set the CRB CSB address field & C bit to indicate a valid + CCB + + + + If the operation notification is asynchronous notify, + then: + + + + Check that the flags parameter interrupt index value is within + the defined range for the validated rid and is not currently in use for + another outstanding COP operation else return H_INTERRUPT. + + + + Set the CRB CM field to command a completion interrupt,. + + + + Set the job id field in the Co-processor Completion Block to + command the signaling via the interrupt source number contained the + interrupt specifier indicated by the interrupt index value. + + + + For the CMO option, if the number of entitlement granules pinned + for this operation causes the partition memory entitlement to be + exhausted then return H_NOT_ENOUGH_RESOURCES; else pin and record the + entitlement granules used by this operation, and increment the partition + consumed memory entitlement for the number of entitlement granules pinned + for this operation. + + + + + + Set the completion code field in the passed (via csbcpb + parameter) CSB to invalid (it is subsequently set to valid at the end of + the operation just after the rest of the contents of the 4k naturally + aligned page specified by the csbcpb parameter are filled). + + + + Issue icswx + + + + If busy response to icswx implementation dependent (may be null) + retry after backoff based upon some usage equality/priority mechanisms + else return H_Busy. + + + + If the operation notification is asynchronous then Return + H_Success + + + + Wait for completion posting in CSB (CSB valid bit. 1) + + + + The contents of the 4K naturally aligned page specified by the + csbcpb parameter are filled from the hypervisor csb and cpb with + addresses converted from real to calling partition logical real + + + + Return H_Success. + + + + +
+ +
+ H_STOP_COP_OP + The architectural intent of this hcall() is to terminate a + previously initiated co-processor operation. + + + + + Semantics: + + + + Check the rid parameter for validity for the caller else return + H_RH_PARM + + + If any reserved flags parameter bits are non zero then return + H_Parameter. + + + Check the csbcpb parameter for pointing within the caller’s + partition and 4K aligned else return H_P3 + + + For the shared logical resource option if the csbcpb parameter + references a rescinded shared logical resource then return + H_RESCINDED + + + If the csbcpb parameter is not associated with an outstanding + coprocessor operation then return H_NOT_ACTIVE. + + + Send a kill operation to the coprocessor handling the outstanding + operation + + + Wait for the outstanding kill operation to complete. + + + For the CMO option, unpin any entitlement granules still pinned + for this operation and decrement the consumed partition memory + entitlement for the number of entitlement granules pinned for this + operation. + + + Return H_Success. + + + +
+
+
+ diff --git a/Virtualization/ch_platform_hcalls.xml b/Virtualization/ch_platform_hcalls.xml new file mode 100644 index 0000000..abf23c2 --- /dev/null +++ b/Virtualization/ch_platform_hcalls.xml @@ -0,0 +1,617 @@ + + Platform Dependent hcall()s + + This chapter defines the set of hypervisor calls (hcall()s) that are + platform dependent. The existence and/or implementation of the hcall() can + vary between firmware releases and between hardware platforms. +
+ hcall()s Supported by Firmware Release & Hardware + Platform + + is a list of platform specific + hcall()s, which will be described in this chapter. + + + Platform Dependent hcall()s Supported by Release and + Hardware Platform + + + + + + + + + Function Name/Section + + + Hypervisor Call Function Token + + + Firmware Releases Supported + + + Hardware Platform Supported + + + + + + + Reserved + + + 0xF000-0xF07C + + +   + + +   + + + + + H_GetPerformanceCounterInfo / + + + + 0xF080 + + + eFW 3.5 and later + + + Power 6 and later + + + + +
+
+
+ Supported hcall()s +
+ H_GetPerformanceCounterInfo (0xF080) + This call returns information about the performance of selectable + performance counters maintained by the hardware or from data collected by + the Hypervisor. + + + Syntax: + + + + + + + Parameters: + + + + size – size of the getPerformanceCounterInfoParms + + + + getPerformanceCounterInfoParms – parameter list indicating + which performance counter information to retrieve. + + + + + + + Semantics: + + + + Validate the getPerformanceInfoParms is accessible, else + H_Privilege. + + + + Validate the size and contents of getPerformanceCounterInfoParms, + else H_Parameter. + + + + Validate information is available for the firmware level and + platform, else H_Not_Available. + + + + Validate partition is permitted to retrieve performance + information, else H_Authority. + + + + Copy requested performance counters into getPerformanceInfoParms + and return H_Success. + + + + + Performance_Counter_Info_Parms struct + + + + + + + + + Member Name + + + Member Type + + + IN/OUT + + + Description + + + + + + + Requested_Information + + + uint_32 + + + INPUT + + + See + + + + + + starting_index + + + int_32 + + + BOTH + + + At input, the partition id of the first + processor/partition to retrieve performance metrics. If -1 is + specified for this parameter, only information for the current + processor/partition is returned. + At output, the actual first processor/partition id that + was found. + + + + + returned_values + + + uint_32 + + + OUTPUT + + + Number of lists of counters returned + + + + + reserved + + + uint_32 + + + N/A + + + Alignment + + + + + reserved + + + uint_64[2] + + + N/A + + + Alignment + + + + + counter_value + + + perf_data + + + BOTH + + + Array of counters values + + + + +
+ The possible values for Requested_Information are as shown in + . + + + Performance Counter Info Requested_Information + Values + + + + + + + + + Name + + + + + Value + + + + + Description + + + + + + + + Dispatch_PURR_by_processor + + + 0x0000 0010 + + + The value for the counter_value is a list of values per + physical processor as follows: + + + uint64 processor time (in PURR cycles) that the processor + was running work on behalf of partitions since the boot of the + CEC + + + uint32 hardware processor id + + + uint16 owning partition id (0xFFFF is shared or + unowned) + + + uint8 processor state (0x01-Not Installed, 0x02-Guarded + Off, 0x03-Unlicensed, 0x04-Shared, 0x05-Borrowed, + 0x06-Dedicated) + + + uint8[1] reserved + + + uint32 hardware chip id (a value of -1 will be returned + for Not Installed processors) + + + uint32 hardware module id + + + uint32 primary affinity domain + + + uint32 secondary affinity domain + + + uint32 processor version (a value of -1 will be returned + for Not Installed processors) + + + uint16 logical processor index + + + uint8[10] reserved + + + + + + + Entitled_capped + _uncapped_donated + _idle_PURR + _by_partition + + + 0x0000 0020 + + + The value for the counter_value is a list of uint64 + values as follows: + Partition id + + + Hypervisor collected PURR cycles that the partition was + entitled to consume since the boot of the CEC (or partition + creation). + + + Hypervisor collected PURR cycles that the partition + consumed as capped cycles since boot of the CEC (or partition + creation). For a dedicated partition, all cycles consumed will + be reported as capped cycles. For shared, these are the capped + (entitled) cycles consumed by the partition. + + + Hypervisor collected PURR cycles that the partition + consumed as uncapped shared partition cycles since boot of the + CEC (or partition creation). + + + Hypervisor collected PURR cycles that were donated from a + dedicated partition to uncapped partitions since boot of the + CEC (or partition creation). + + + Partition collected PURR cycles that the partition + considers as idle cycles. These cycles can be subtracted from + the total cycles consumed to calculate the partition’s + view of utilization. Note that not all operating system + versions will report this value. + + + + + + + Run_instructions + _run_cycles + _by_partition + + + 0x0000 0030 + + + The value for the counter_value is a list of uint64 + values as follows: + + + Partition id + + + Hypervisor collected instructions completed while the run + latch is set since boot of the CEC (or partition creation). + Note that this value will be zero on processors versions that + do not provide the ability to collect this information. + + + Hypervisor collected cycles while the run latch is set + since boot of the CEC (or partition creation). Note that this + value will be zero on processors versions that do not provide + the ability to collect this information. + + + + + + + System_performance + _capabilities + + + 0x00000040 + + + The value for the counter_value is a list of values for + the requesting partition as follows: + + + uint8 Is partition allowed to get performance data for + other partitions (boolean). + + + uint8[15] Reserved + + + Note: This request can only be issued by a partition to + obtain data about itself (i.e. starting_index must always be + -1) H_NOT_AVAILABLE will be returned otherwise. + + + + + + + Processor_bus_utilization_ABC + _links + + + 0x00000050 + + + The value for the counter_value is a list of values per + physical chip as follows: + + + uint32 hardware chip id + + + uint32[3] RESERVED + + + uint64 idle cycles for A link + + + uint64 time value (in cycles) data for A link was + collected + + + uint64 idle cycles for B link + + + uint64 time value (in cycles) data for B link was + collected + + + uint64 idle cycles for C link + + + uint64 time value (in cycles) data for C link was + collected + + + + + + + Processor_bus_utilization_WXYZ + _links + + + 0x00000060 + + + The value for the counter_value is a list of values per + physical chip as follows: + + + uint32 hardware chip id + + + uint32[3] RESERVED + + + uint64 idle cycles for W link + + + uint64 time value (in cycles) data for W link was + collected + + + uint64 idle cycles for X link + + + uint64 time value (in cycles) data for X link was + collected + + + uint64 idle cycles for Y link + + + uint64 time value (in cycles) data for Y link was + collected + + + uint64 idle cycles for Z link + + + uint64 time value (in cycles) data for Z link was + collected + + + + + + + Set MMCRH + (LAB ONLY) + + + 0x8000 1000 + + + At input, counter_value is a single value with what to + set the Performance Monitor Mode Control Register H to: + + + uint64 value to set MMCRH to in all processors + + + There will be no output for this function other than + errors. + + Note 1: A passed value of (-1) will mean + that collection of these values should be disabled. + + Note 2: Whenever this value is changed, the + programmable counters (HPMC1 & HPMC2) will be reset in the + next collection cycle. + + + + + Retrieve HPMCx + (LAB ONLY) + + + 0x8000 2000 + + + The value for the counter_value is a list of values per + physical processor as follows: + + + uint32 hardware processor id + + + uint32 reserved + + + uint64 current value of MMCRH for this processor + + + uint64 elapsed timebase value in cycles since current + MMCRH was set + + + uint64 value for HPMC1 since current MMCRH was set + + + uint64 value for HPMC2 since current MMCRH was set + + + uint64 value for HPMC3 since current MMCRH was set + + + uint64 current value for HPMC3 + + + uint64 value for HPMC4 since current MMCRH was set + + + uint64 current value for HPMC4 + + + + + + +
+ +
+
+ diff --git a/Virtualization/ch_splpar.xml b/Virtualization/ch_splpar.xml new file mode 100644 index 0000000..444aca8 --- /dev/null +++ b/Virtualization/ch_splpar.xml @@ -0,0 +1,535 @@ + + SPLPAR Characteristics Definitions +
+ SPLPAR Characteristics Definitions + + This chapter defines the string that is returned by the + ibm,get-system-parameter RTAS call when the parameter token value of 20 + (SPLPAR Characteristics) is specified on the ibm,get-system-parameter RTAS + call as per . +
+
+ SPLPAR Terms + The LoPAR Shared Processor Logical Partition option (SPLPAR) defines + many terms as presented in + . + + + SPLPAR Terms + + + + + + + + Term + + + + + Definition + + + + + + + + Bound Threads + + + For virtual processor dispatches, if the hypervisor always + dispatches a set of virtual threads together on a physical + processor, the threads are said to be bound. This allows an + operating system to make scheduling decisions based on cache + affinity and work load. A change in this characteristic takes + effect on the next reboot of the partition. + + + + + Capacity Increment + + + This defines the delta by which the entitled capacity of a + partition can be incremented or decremented by DLPAR/WLM. The + capacity increment is expressed as a percentage of a physical + processor. A change in the capacity increment takes effect on the + next reboot of the partition. + + + + + Desired Entitled Capacity + + + The desired entitled capacity set by the system + administrator in the partition definition. The desired entitled + capacity is expressed as a percentage of a physical processor. + The desired entitled capacity can change without a reboot of the + partition. The entitled capacity that the partition is currently + using may differ from the desired entitled capacity because of + WLM actions or failed system processors. + + + + + Desired Memory + + + The desired memory set by the system administrator in the + partition definition. The desired memory is expressed in MB of + storage. The desired memory can change without a reboot of the + partition. The desired memory that the partition is currently + using may differ from the desired memory because of WLM actions + or because of failed system memory. + + + + + Desired Number of Processors + + + The desired number of virtual processors set by the system + administrator in the partition definition. The desired number of + processors can change without a reboot of the partition. The + number of processors that the partition is currently using may + differ from the desired number of processors because of WLM + actions or because of failed system processors. + + + + + Desired Variable Capacity Weight + + + The desired variable capacity weight set by the system + administrator in the partition definition. The desired variable + capacity weight is a number between 0 and 255. The desired + variable capacity weight can change without a reboot of the + partition. The variable capacity weight that the partition is + currently using may differ from the desired variable capacity + because of WLM actions. + + + + + Dispatch Wheel Rotation Period + + + The duration of the hypervisor’s scheduling window. + The time over which the entitled capacity of a virtual processor + has to be utilized by the partition. At the start of a dispatch + wheel rotation period, each virtual processor is eligible for CPU + time corresponding to its entitled capacity. If the entire + entitled capacity of a virtual processor is not utilized during a + dispatch wheel rotation period, the unused entitled capacity is + lost. The dispatch wheel rotation period is expressed as N number + of time base ticks. The dispatch wheel duration of a partition + with a capacity increment of 100 is 0. A change in the dispatch + wheel rotation period takes effect on the next reboot of the + partition. + + + + + Minimum Entitled Capacity + + + The minimum entitled capacity that is needed to power on + the partition. The capacity is expressed as a percentage of a + physical processor. The minimum entitled capacity is set by the + system administrator in the partition definition. DLPAR cannot + take the entitled capacity below the minimum entitled capacity. A + change in the minimum entitled capacity takes effect on the next + reboot of the partition. A partition can give up its entitled + capacity to be below the minimum entitled capacity. + + + + + Minimum Entitled Capacity per Virtual Processor + + + The minimum entitled capacity that the platform requires + for a virtual processor of any partition on the platform. The + minimum virtual per virtual processor is enforced by the HMC in + the partition definition and by the hypervisor for H_SET_PPP ( + ). A change in the + minimum entitled capacity per virtual processor takes effect on + the next reboot of the partition. + + + + + Minimum Memory + + + The minimum amount of main store that is needed to power on + the partition. Minimum memory is expressed in MB of storage. The + minimum memory is set by the system administrator in the + partition definition. DLPAR cannot take the partition memory + below the minimum memory. A change in the minimum memory takes + effect on the next reboot of the partition. A partition can + always give up its memory to go below the minimum memory. + + + + + Minimum Number of Processors + + + The minimum number of virtual processors that are needed to + start the partition. The minimum number of virtual processors is + set by the system administrator in the partition definition. + DLPAR cannot take the number of virtual processors below the + minimum number of processors. A change in the minimum number of + processors takes effect on the next reboot of the partition. A + partition can always give up its virtual processors to go below + the minimum number of processors. + + + + + Maximum Entitled Capacity + + + The maximum entitled capacity currently that can be + assigned to the partition through DLPAR/WLM. The capacity is + expressed as a percentage of a physical processor. The Maximum + entitled capacity is set up by the system administrator in the + partition definition. A change in the maximum entitled capacity + maximum takes effect on the next reboot of the partition. + + + + + Maximum Platform Processors + + + The maximum number of processors that can be active on the + platform. A change in the maximum platform processors takes + effect on the next reboot of the partition. + + + + + Dedicated Donate Mode + + + For a partition with a capacity increment of 100, the + platform uses a dedicated CPU to actualize a virtual processor of + the partition. For such a partition, the platform can increase + the capacity of the shared processor pool by utilizing the unused + processor capacity of the partition. If the platform supports the + dedicated donate function, it can be enabled by the system + administrator in the partition definition. The value of this + characteristic can change without a reboot of the + partition. + + + + + Thread + + + A multi threaded processor may have multiple contexts + executing concurrently. Each of them is called a thread. From a + software viewpoint, a thread is an independent executing unit. + Threads on a processor share some of the architected and + unarchitected resources of a physical processor. + + + + +
+
+
+ Key Words And Values + Table + defines the key words and the + associated legal values that will be returned in the ASCII NULL terminated + string when the parameter token value of 20 (SPLPAR characteristics) is + specified on the ibm,get-system-parameter RTAS call. The key word and value + is separated by an ascii equal (“=”). Each key word, value pair + is delimited by an ascii comma in the string. The numerical value of the + characteristic corresponding to the key word is the decimal number that + corresponds to the numeric characters in the value part of the key word, + value pair. + + SPLPAR Characteristics + + + + + + + + + + + Characteristics + + + + + Key Word + + + + + Values + + + + + Notes + + + + + + + + Bound Threads + + + BoundThrds + + + 0,1 + + + 1 + + + + + Capacity Increment + + + CapInc + + + 1 through 100 + + +   + + + + + Dispatch Wheel Rotation Period + + + DisWheRotPer + + + 1 through N + + +   + + + + + Minimum Entitled Capacity + + + MinEntCap + + + 0 through N + + + 2 + + + + + Minimum Entitled Capacity per Virtual Processor + + + MinEntCapPerVP + + + 1 through 100 + + +   + + + + + Minimum Memory + + + MinMem + + + 0 through N + + +   + + + + + Minimum Number of Processors + + + MinProcs + + + 0 through N + + +   + + + + + Maximum Entitled Capacity + + + MaxEntCap + + + 1 through N + + + 3 + + + + + Maximum Platform Processors + + + MaxPlatProcs + + + 1 through N + + +   + + + + + Desired Entitled Capacity + + + DesEntCap + + + 0 through N + + + 4 + + + + + Desired Memory + + + DesMem + + + 0 through N + + + 5 + + + + + Desired Number of Processors + + + DesProcs + + + 0 through N + + + 6 + + + + + Desired Variable Capacity Weight + + + DesVarCapWt + + + 0 through 255 + + +   + + + + + Dedicated Donate Mode + + + DedDonMode + + + 0,1 + + + 7 + + + + +
+ Notes: + + + 0=Threads are not bound, 1=Threads are bound. + + + + The maximum numeric value of Minimum Entitled Capacity is the + number of processors on the platform multiplied by 100. + + + + The maximum numeric value of Maximum Entitled Capacity is the + number of processors on the platform multiplied by 100. + + + + The numeric value of Desired Entitled Capacity is greater or equal + than the numeric value of the Minimum Entitled Capacity and less than or + equal to the numeric value of the Maximum Entitled Capacity. + + + + The numeric value of Desired Memory is greater or equal than the + numeric value of the Minimum Memory and less than or equal to the maximum + memory set by the system administrator in the partition profile. + + + + The numeric value of Desired Number of Processors is greater or + equal than the numeric value of the Minimum Number of Processors and less + than or equal to the maximum number of virtual processors set by the system + administrator in the partition profile. + + + + 0=Dedicated Donate Mode is disabled, 1=Dedicated Donate Mode is + enabled. + + + +
+ diff --git a/Virtualization/ch_virtual_io.xml b/Virtualization/ch_virtual_io.xml new file mode 100644 index 0000000..dcdacc2 --- /dev/null +++ b/Virtualization/ch_virtual_io.xml @@ -0,0 +1,14520 @@ + + Virtualized Input/Output + Virtualized I/O is an optional feature of platforms that have + hypervisor support. Virtual I/O (VIO) provides to a given partition the + appearance of I/O adapters that do not have a one to one correspondence with + a physical IOA. The hypervisor uses one of three techniques to realize a + virtual IOA: + + + + In the + hypervisor simulated class, the hypervisor may totally + simulate the adapter. For example, this is used in the virtual ethernet (IEEE + VLAN) support (see + ). This technique is applicable to + communications between partitions that are created by a single hypervisor + instance. + + + + In the + partition managed class, a + server partition provides the services of one of its + IOA’s to a + partner partition(s) (one or more + client partitions + The term “hosted” is sometimes used for + “client” and the term “hosting” is sometimes used + for “server.” Note that a server IOA or partition can sometimes + also be a client, and vice versa, so the terminology “client” + and “server” tend to be less confusing than hosted and + hosting. + or one or more server partitions). In limited cases, a client may + communicate directly to a client. A server partition provides support to + interpret I/O requests from the partner partition, perform those requests on + one or more of its devices, targeting the partner partition’s DMA + buffer areas (for example, by using the Remote DMA (RDMA) facilities), and + passing I/O responses back to the partner partition. For example, see + . + + + + In the + hypervisor managed class, the hypervisor may provide low + level hardware management (error and sub-channel allocation) so that + partition level code may directly manage its assigned sub-channels. + + + + + This chapter is organized from general to specific. The overall + structure of this architecture is as shown in + . + +
+ VIO Architecture Structure + + + + + + + + +
+ +
+ Terminology used with VIO + Besides the general terminology defined on the first page of this + chapter, + will assist the reader in understanding the content of this chapter. + + + Terminology used with VIO + + + + + + + Term + + + Definition + + + + + + + VIO + + + Virtual I/O. General term for all virtual I/O classes and + virtual IOAs. + + + + + ILLAN + + + Interpartition Logical LAN. This option uses the + hypervisor simulated class of virtual I/O to provide + partition-to-partition LAN facilities without a real LAN IOA. + See + . + + + + + VSCSI + + + Virtual SCSI. This option provides the facilities for + sharing physical SCSI type IOAs between partitions. + . + + + + + ClientClient VIO model + + + This terminology is mainly used with the partition + managed class of VIO. The client, or client partition, is an + entity which generally requests of a server partition, access + to I/O to which it does not have direct access (that is, access + to I/O which is under control of the server partition). Unlike + the server, the client does not provide services to other + partitions to share the I/O which resides in their partition. + However, it possible to have the same partition be both a + server and client partition, but under different virtual IOAs. + The Client VIO model is one where the client partition maps + part of its local memory into an RTCE table (as defined by the + first window pane of the + “ibm,my-dma-window”property), + so that the server partition can get access to that + client’s local memory. An example of this is the VSCSI + client (see + for more + information). + + + + + ServerServer VIO model + + + This terminology is mainly used with the partition + managed class of VIO. The server, or server partition is an + entity which provides a method of sharing the resources under + its direct control with another partition, virtualizing those + resources in the process. The following defines the Server VIO + model: + The server is a server to a client. An example of this is + the VSCSI client (see + ). In this case, the + Server VIO model is one where the server gets access to the + client partition’s local memory via what the client + mapped into an RTCE table. This access is done through the + second window pane of the server’s + “ibm,my-dma-window”property, + which is linked to the first window pane of the client’s + “ibm,my-dma-window”property. + + + + + Partner partition + + + This is “the other” partition in a pair of + partitions which are connected via a virtual IOA pair. For + client partitions, the partner is generally the server + (although, in limited cases, client to client connections may + be possible). For server partitions, the partner can be a + client partition or another server partition. + + + + + RTCE table + + + Remote DMA TCE table. TCE (Translation Control Entry) and + RTCE tables are used to translate I/O DMA operations and + provide protection against improper operations (access to what + should not be accessed or for protection against improper + access modes, like writing to a read only page). More + information on TCEs and TCE tables, which are used for physical + IOAs, can be found in + . The RTCE table for Remote + DMA (RDMA) is analogous to the TCE table for physical IOAs. The + RTCE table does, however, have a little more information in it + (as placed there by the hypervisor) in order to, among other + things, allow the hypervisor to create links to physical IOA + TCEs that were created from the RTCE table TCEs. A TCE in an + RTCE table is never accessed directly by the partitions + software; only though hypervisor hcall()s. For more information + on RTCE table and operations, see + , and + . + + + + + Window pane + (“ibm,my-dma-window” property) + + + The RTCE tables for VIO DMA are pointed to by the + “ibm,my-dma-window” property in + the device tree for each virtual device. This property can have + one, two, or three triples, each consisting of a Logical I/O + Bus Number (LIOBN), phys which is 0, and size. The LIOBN + essentially points to a unique RTCE table (or a unique entry + point into a single table. The phys is a value of 0, indicating + offsets start at 0. The size is the size of the available + address space for mapping memory into the RTCE table. This + architecture talks about these unique RTCE tables as being + window panes within the + “ibm,my-dma-window” property. + Thus, there can be up to three window panes for each virtual + IOA, depending on the type of IOA. For more on usage of the + window panes, see + . + + + + + RDMA + + + Remote Direct Memory Access is DMA transfer from the + server to its client or from the server to its partner + partition. DMA refers to both physical I/O to/from memory + operations and to memory to memory move operations. + + + + + Copy RDMA + + + This term refers to when the hypervisor is used (possibly + with hardware assist) to move data between server partition and + client partition memories or between server partition and + partner partition memories. See + . + + + + + Redirected RDMA + + + This term refers to when the TCE(s) for a physical IOA + are set up through the use of the RTCE table manipulation + hcall()s (for example, H_PUT_RTCE) such that the client or + partner’s partition’s RTCE table (though the second + window pane of the server partition) is used by the hypervisor + during the processing of the hcall() to setup the TCE(s) for + the physical IOA, and then the physical IOA DMAs directly to or + from the client or partner partition’s memory. See + for more + information. + + + + + LRDMA + + + Stands for Logical Remote DMA and refers to the set of + facilities for synchronous RDMA operations. See also + for more information. + LRDMA is a separate option. + + + + + Command/Response Queue (CRQ) + + + The CRQ is a facility which is used to communicate + between partner partitions. Transport events which are signaled + from the hypervisor to the partition are also reported in this + queue. + + + + + Subordinate CRQ (Sub-CRQ) + + + Similar to the CRQ, except with notable differences (See + ). + + + + + Reliable Command/Response Transport + + + This is the CRQ facility used for synchronous VIO + operations to communicate between partner partitions. Several + hcall()s are defined which allow a partition to place an entry + on the partner partition’s queue. The firmware can also + place transport change of status messages into the queue to + notify a partition when the connection has been lost (for + example, due to the other partition crashing or deregistering + its queue). See + for more + information. + + + + + Subordinate CRQ Transport + + + This is the Sub-CRQ facility used for synchronous VIO + operations to communicate between partner partitions when the + CRQ facility by itself is not sufficient. The Subordinate CRQ + Transport never exists without a corresponding Reliable + Command/Response Transport. See + for more + information. + + + + +
+
+ +
+ VIO Architectural Infrastructure + VIO is used in conjunction with the Logical Partitioning option as + described in + . For each of a platform’s + partitions, the number and type of VIO adapters with the associated + interpartition communications paths (if any are defined). These definitions + take the architectural form of VIO adapters and are communicated to the + partitions as device nodes in their OF device tree. Depending upon the + specific virtual device, their device tree node may be found as a child of + / (the root node) or in the VIO sub-tree (see + below). + The VIO infrastructure provides several primitives that may be used + to build connections between partitions for various purposes (that is, for + various virtual IOA types). These primitives include: + + + + A Command/Response Queue (CRQ) facility which provides a pipe + between partitions. A partition can enqueue an entry on its partner’s + CRQ for processing by that partner. The partition can set up the CRQ to + receive an interrupt when the queue goes from empty to non-empty, and hence + this facility provides a method for an inter-partition interrupt. + + + + A Subordinate CRQ (Sub-CRQ) facility that may be used in + conjunction with the CRQ facility, when the CRQ facility by itself is not + sufficient. That is, when more than one queue with more than one interrupt + is required by the virtual IOA. + + + + An extended TCE table called the RTCE table which allows a + partition to provide “windows” into the memory of its partition + to its partner partition, while maintaining addressing and access control + to its memory. + + + + Remote DMA services that allow a server partition to transfer data + to a partner partition’s memory via the RTCE table window panes. This + allows a device driver in a server partition to efficiently transfer data + to and from a partner, which is key in sharing of an IOA in the server + partition with its partner partition. + + + + In addition to the virtual IOAs themselves, this architecture defines + a virtual host bridge, and a virtual interrupt source controller. The + virtual host bridge roots the VIO sub-tree. The virtual interrupt source + controller provides the consistent syntax for communicating the interrupt + numbers the partition’s OS sees when the virtual IOAs signal an + interrupt. + The general VIO infrastructure is defined in + . There are additional + infrastructures requirements for the partition managed class based on the + Synchronous VIO model. See + . + +
+ VIO Infrastructure - General + This section describes the general OF device tree structure for + virtual IOAs and describes in more detail window panes, as well as + describing the interrupt control aspects of virtual IOAs. + +
+ Properties of the + <emphasis role="bold"><literal>/vdevice</literal></emphasis> OF Tree Node + Most VIO adapters are represented in the OF device tree as children + of the + /vdevice node (child of the root node). While the + vdevice sub-tree is the preferred architectural home for VIO adapters, + selected devices for historical reasons, are housed outside of the + vdevice sub-tree. + + + + R1--1. + + + /vdevice node must contain the properties as defined + in . + + + + + + Properties of the <emphasis role="bold"><literal>/vdevice</literal></emphasis> Node + + + + + + + + + Property Name + + + + + Required? + + + + + Definition + + + + + + + + + “name” + + + + Y + + + Standard property name per + , + specifying the virtual device name, the value shall be + “vdevice” + + + + + + “device_type” + + + + Y + + + Standard property name per + , + specifying the virtual device type, the value shall be + “vdevice” + + + + + + “model” + + + + NA + + + Property not present. + + + + + + “compatible” + + + + Y + + + Standard property name per + + , specifying + the virtual device programming models, the value shall include + “IBM,vdevice” + + + + + + “used-by-rtas” + + + + NA + + + Property not present. + + + + + + “ibm,loc-code” + + + + NA + + + The location code is meaningless unless one is doing + dynamic reconfiguration as in the children of this node. + + + + + + “reg” + + + + NA + + + Property not present. + + + + + + “#size-cells” + + + + Y + + + Standard property name per + , + the value shall be 0. No child of this node takes + space in the address map as seen by the owning + partition. + + + + + + “#address-cells” + + + + Y + + + Standard property name per + , + the value shall be 1. + + + + + + “#interrupt-cells” + + + + Y + + + Standard property name per + , + the value shall be 2. The first cell contains the + interrupt# as will appear in the XIRR and is used as input to + interrupt RTAS calls. The second cell contains the value 0 + indicating a positive edge sense + + + + + + “interrupt-map-mask” + + + + NA + + + Property not present. + + + + + + “interrupt-ranges” + + + + Y + + + Standard property name that defines the interrupt + number(s) and range(s) handled by this unit. + + + + + + “ranges” + + + +   + + + These will probably be needed for IB virtual + adapters. + + + + + + “interrupt-map” + + + + NA + + + Property not present. + + + + + + “interrupt-controller” + + + + Y + + + The + /vdevice node appears to contain an + interrupt controller. + + + + + + “ibm,drc-indexes” + + + + For DR + + + Refers to the DR slots -- the number provided is the + maximum number of slots that can be configured which is limited + by, among other things, the RTCE tables allocated by the + hypervisor. + + + + + + “ibm,drc-power-domains” + + + + For DR + + + Value of -1 to indicate that no power manipulation is + possible or needed. + + + + + + “ibm,drc-types” + + + + For DR + + + Value of + “SLOT”. Any virtual IOA can + fit into any virtual slot. + + + + + + “ibm,drc-names” + + + + For DR + + + The virtual location code (see + ) + + + + + + “ibm,max-virtual-dma-size” + + + + See definition column + + + The maximum transfer size for H_SEND_LOGICAL_LAN and + H_COPY_RDMA hcall()s. Applies to all VIO which are children of + the + /vdevice node. Minimum value is 128 + KB. + + + + +
+
+ +
+ RTCE Table and Properties of the Children of the + <emphasis role="bold"><literal>/vdevice</literal></emphasis> Node + This architecture defines an extended type of TCE table called a + Remote DMA TCE (RTCE) table. An RTCE table is one that is not directly + used by the hardware to translate an I/O adapter’s DMA addresses, + but is used by the hypervisor to translate a partition’s I/O + addresses. RTCE tables have extra data, compared with a standard TCE + table, to help firmware manage the use of its mappings. A partition + manages the entries for its memory that is to be the target for I/O + operations in the RTCE table using the TCE manipulation hcall()s, + depending on the type of window pane. More on this later in this section. + On platforms implementing the CRQ LRDMA options, these hcall()s are + extended to understand the format of the RTCE table via the LIOBN + parameter that is used to address the specific window pane within an RTCE + table + One could also think of each LIOBN pointing to a separate RTCE + table, rather than window panes within an RTCE table. + . + Children of the + /vdevice node that support operations which use RTCE + tables (for example, RDMA) contain the + “ibm,my-dma-window” property. This + property contains one or more (logical-I/O-bus-number, phys, size) + triple(s). Each triple represents one window pane in an RTCE table which + is available to this virtual IOA. The phys value is 0, and hence the + logical I/O bus number (LIOBN) points to a unique range of TCEs in the + RTCE table which are assigned to this window pane (LIOBN), and hence the + I/O address for that LIOBN begin at 0. + The LIOBN is an opaque handle which references a window pane within + an RTCE table. Since this handle is opaque, its internal structure is not + architected, but left to the implementation’s discretion. However, + it is the architectural intent that the LIOBN be an indirect reference to + the RTCE table through a hypervisor table that contains management + variables, allowing for movement of the RTCE table and table format + specific access methods. The partition uses an I/O address as an offset + relative to the beginning of the LIOBN, as part of any I/O request to + that memory mapped by that RTCE table’s TCEs. A server partition + appends its version of the LIOBN for the partner partition’s RTCE + table that represents the partner partition’s RTCE table which it + received through the second entry in the + “ibm,my-dma-window” property associated + with server partition’s virtual IOA’s device tree node (for + example, see + ). The mapping between the + LIOBN in the second pane of a server virtual IOA’s + “ibm,my-dma-window” property and the + corresponding partner partition IOA’s RTCE table is made when the + CRQ successfully completes registration. + The window panes and the hcall()s that are applicable to those + panes, are defined and used as indicated in + . + + + VIO Window Pane Usage and Applicable Hcall()s + + + + + + + + + + Window Pane (Which Triple) + + + + + Hypervisor Simulated Class + + + + + Client VIO Model + + + + + Server VIO Model + + + + + + + + First + + + + + I/O address range which is available to map local + partition memory for use by the hypervisor + + + + + + + I/O address range which is available to map local + partition memory to make it available to the hypervisor use + (access to the CRQ and any Sub-CRQs). + + + For clients which support RDMA operations from their + partner partition to their local memory (for example, VSCSI), + this I/O address range is available to map local partition + memory to make it available to the server partition, and this + pane gets mapped to the second window pane of the partner + partition (client/server relationship). + + + + + + + I/O address range which is available to map local + partition memory for use by the hypervisor (for access by + H_COPY_RDMA requests, and for access to the CRQ, any + Sub-CRQs). + + + This window is not available to any other + partition. + + + + + + + Applicable hcall()s: H_PUT_TCE, H_GET_TCE, + H_PUT_TCE_INDIRECT, H_STUFF_TCE + + + + + Second + + + Does not exist + + + Does not exist + + + + + I/O address range which corresponds to a window pane of + the partner partition: linked to the first window pane for + Client/Server model connections. + + + Used to get access to the partner partition’s + memory from the hypervisor that services the local partition + for use as source or destination in Copy RDMA requests or for + redirected DMA operations (for example, H_PUT_RTCE). + + + + + + + Applicable hcall()s: H_PUT_RTCE, H_REMOVE_RTCE and + H_PUT_RTCE_INDIRECT + + + + +
+ The + “ibm,my-dma-window” property is the per + device equivalent of the + “ibm,dma-window” property found in nodes + representing bus bridges. + Children of the + /vdevice node contain virtual location codes in their + + “ibm,loc-code” properties. The invariant + assignment number is uniquely generated when the virtual IOA is assigned + to the partition and remains invariably associated with that virtual IOA + for the duration of the partition definition. For more information, see + . +
+ +
+ VIO Interrupt Control + There are two hcall()s that work in conjunction with the RTAS calls + + ibm,int-on, + ibm,int-off, + ibm,set-xive and + ibm,get-xive, which manage the state of the + interrupt presentation controller logic. These hcall()s provide the + equivalent of IOA control registers used to control IOA interrupts. The + usage of these two hcall()s is summarized in + . The detail of the + H_VIO_SIGNAL is shown after this table and the detail of the applicable + H_VIOCTL subfunctions can be found in + , + , and + . + + + VIO Interrupt Control hcall() Usage + + + + + + + + + + Interrupt From + + + + + Virtual IOA Definition does + not + Include Sub-CRQs + + + + + Virtual IOA Definition + Includes + Sub-CRQs + + + + + Interrupt Number Obtained + From + + + + + + + + CRQ + + + H_VIO_SIGNAL + + + H_VIO_SIGNAL + or + H_VIOCTL + + + OF device tree + “interrupts” property + + + + + Sub-CRQ + + + Not Applicable + + + H_VIOCTL + + + H_REG_SUB_CRQ hcall() + + + + +
+ +
+ H_VIO_SIGNAL + This H_VIO_SIGNAL hcall() manages the interrupt mode of a virtual + adapter’s CRQ interrupt signalling logic. There are two modes: + Disabled, and Enabled. + The first interrupt of the + “interrupts” property is for the + CRQ. + + + Syntax: + + + + + + + Parameters: + + + + unit-address: unit address per device tree node + “reg” property. + + + + mode: + + + + Bit 63 controls the first interrupt specifier given in the + virtual IOA’s + “interrupts” property, and bit 62 the + second. High order bits not associated with an interrupt source as + defined in the previous sentence should be set to zero by the caller and + ignored by the hypervisor. + + + + A bit value of 1 enables the specified interrupt, a bit value of + 0 disables the specified interrupt. + + + + + + + + Semantics: + + + + Validate that the unit address belongs to the partition and to a + vdevice IOA, else H_Parameter. + + + + Validate that the mode is one of those defined, else + H_Parameter. + + + + Establish the specified mode. + + + + Return H_Success. + + + +
+
+ +
+ General VIO Requirements + + + + R1--1. + + + For all VIO options: The platform must be running in + LPAR mode. + + + + + R1--2. + + + For all VIO options: The platform’s OF device + tree must include, as a child of the + root node, a node of type + vdevice as the parent of a sub-tree representing the + virtual IOAs assigned to the partition (see + for details). + + + + + R1--3. + + + For all VIO options: The platform’s + /vdevice node must contain properties as defined in + . + + + + + R1--4. + + + For all VIO options: If the platform is going to + limit the size of virtual I/O data copy operations (e.g., + H_SEND_LOGICAL_LAN and H_COPY_RDMA), then the platform’s + /vdevice node must contain the + “ibm,max-virtual-dma-size” property, and + the value of this property must be at least 128 KB. + + + + + R1--5. + + + For all VIO options: The interrupt server numbers for + all interrupt source numbers, virtual and physical, must come from the + same name space and are defined by the + “ibm,interrupt-buid-size” property in the + PowerPC External Interrupt Presentation + Controller Node. + + + + + R1--6. + + + For all VIO options: The virtual interrupts for all + children of the + /vdevice node must, upon transfer of control to the + booted partition program, be masked as would be the result of an + ibm,int-off RTAS call specifying the virtual + interrupt source number. + + + + + R1--7. + + + For all VIO options with the Reliable Command/Response + option: The platform must specify the CRQ interrupt as the + first interrupt in the + “interrupts” property for a virtual + IOA. + + + + + R1--8. + + + + Reserved + + + + + R1--9. + + + For all VIO options: The platform must implement the + H_VIO_SIGNAL hcall() as defined in + . + + + + + R1--10. + + + For all VIO options: The platform must assign an + invariant virtual location code to each virtual IOA as described in + . + + + + + + R1--11. + + + (Requirement Number Reserved For Compatibility) + + + + + + R1--12. + + + For all VIO options: The + phys of each + “ibm,my-dma-window” property triple + (window pane) must have a value of zero and the LIOBN must be + unique. + Implementation Note: While the architectural + definition of LIOBN would allow the definition of one logical I/O bus + number (LIOBN) for all RTCE tables (IOBA ranges separating IOAs), such an + implementation is not permitted for the VIO option, which requires a + unique LIOBN (at least per partition preferably platform wide) for each + virtual IOA window pane. Such designs allow the LIOBN handle to be used + to validate access rights, and allows each subsequent I/O bus address + range to start at zero, providing maximum accommodation for 32 bit + OS’s. + + + + + R1--13. + + + For the VSCSI option: + For the server + partition, there must exist two triples (two window panes) in the + “ibm,my-dma-window” property and the size + field of the second triple (second window pane) of an + “ibm,my-dma-window” property must be + equal to the size field of the corresponding first triple (first window + pane) of the associated partner partition’s + “ibm,my-dma-window” property. + + + + + R1--14. + + + + Reserved + + + + + R1--15. + + + For all VIO options: + RTCE tables for + virtual IOAs, as pointed to by the partitions’ first window pane of + the + + “ibm,my-dma-window” property, and the + TCEs that they contain (as built by the TCE hcall()s) must be persistent + across partner partition reboots and across partner partition deregister + (free)/re-register operations, even when the partition which connects + after one deregisters is a different partition, and must be available to + have TCEs built in them by said partition, as long as that partition + still owns the corresponding virtual IOA (an LRDR operation which removes + the IOA will also remove the RTCE table). + + + + + R1--16. + + + For all VIO options: The connection between the + second window pane of the + “ibm,my-dma-window” property for a + partition and its corresponding window pane in the partner partition + (first window pane) must be broken by the platform when either partition + deregisters its CRQ or when either partition terminates, and the platform + must invalidate any redirected TCEs copied from the said second window + pane (for information on invalidation of TCEs, see + ). + + + + + + R1--17. + + + For all VIO options: The following window panes of + the “ibm,my-dma-window” + property, when they exist, must support the following specified hcall()s, when they are + implemented: + + + + For the first window pane: H_PUT_TCE, H_GET_TCE, + H_PUT_TCE_INDIRECT, H_STUFF_TCE + + + + For the second window pane: H_PUT_RTCE, H_REMOVE_RTCE, + H_PUT_RTCE_INDIRECT + + + + + + + R1--18. + + + For all VIO options: + The platform must not prohibit the server and partner partition, or client and partner + partition, from being the same partition, unless the user interface used + to setup the virtual IOAs specifically disallows such + configurations. + + + + + R1--19. + + + For all VIO options: Any child node of the + /vdevice node that is not defined by this + architecture must contain the + “used-by-rtas” property. + + Implementation Notes: + + + + + Relative to Requirement + , partner partitions being the + same partition makes sense from a product development standpoint. + + + + The + ibm,partner-control RTAS call does not make sense if + the partner partitions are the same partition. + + + + + + + R1--20. + + + For all VIO options: The platform must implement the + H_VIOCTL hcall() following the syntax of + and semantics specified by + . + + + + + +
+ +
+ Shared Logical Resources + The sharing of resources, within the boundaries of a single + coherence domain, owned by a partition owning a server virtual IOA by its + clients (those owning the associated client virtual IOAs) is controlled + by the hcall()s described in this section. The owning partition retains + control of and access to the resources and can ask for their return or + indeed force it. Refer to + for a graphic representation of + the state transitions involved in sharing logical resources. + +
+ Shared Logical Resource State Transitions + + + + + + + + +
+ + Owners of resources can grant, to one or more client + partitions, access to any of its resources. A client partition being + defined as a partition with which the resource owner is authorized to + register a CRQ, as denoted via an OF device tree virtual IOA node. + Granting access is accomplished by requesting that the hypervisor + generate a specific cookie for that resource for a specific sharing + partition. The cookie value thus generated is unique only within the + context of the partition being granted the resource and is unusable for + gaining access to the resource by any other partition. This unique cookie + is then communicated via some inter partition communications channel, + most likely the authorized Command Response Queue. The partner partition + then accepts the logical resource (mapping it into the accepting + partition’s logical address space). The owning partition may grant + shared access of the same logical resource to several clients (by + generating separate cookies for each client). During the time the + resource is shared, both the owner and the sharer(s) have access to the + logical resource, the software running in these partitions use private + protocols to synchronize control access. Once the resource has been + accepted into the client’s logical address space, the resource can + be used by the client in any way it wishes, including granting it to one + of its own clients. When the client no longer needs access to the shared + logical resource, it destroys any virtual mappings it may have created + for the logical resource and returns the logical resource thus unmapping + it from its logical address space. The client program could, subsequently + accept the logical resource again (given that the cookie is still valid). + To complete the termination of sharing, the owner partition rescinds the + cookie describing the shared resource. Normally a rescind operation + succeeds only if the client has returned the resource, however, the owner + can force the rescind in cases where it suspects that the client is + incapable of gracefully returning the resource. + In the case of a forced rescind, the hypervisor marks the client + partition’s logical address map location corresponding to the + shared logical resource such that any future hcall() that specifies the + logical address fails with an H_RESCINDED return code. The hypervisor + then ensures that the client partition’s translation tables contain + no references to a physical address of the shared logical + resource. + Should the server partition fail, the hypervisor automatically + notifies client partitions of the fact via the standard CRQ event + message. In addition, the hypervisor recovers any outstanding shared + logical resources prior to restarting the server partition. This recovery + is proceeded by a minimum of two seconds of delay to allow the client + partitions time to gracefully return the shared logical resources, then + the hypervisor performs the equivalent of a forced rescind operation on + all the server partition’s outstanding shared logical + resources. + This architecture does not specify a method of implementation, + however, for the sake of clarifying the specified function, the following + example implementation is given, refer to + . Assume that the hypervisor + maintains for each partition a logical to physical translation table (2) + (used to verify the partition’s virtual to logical mapping + requests). Each logical resource (4) mapped within the logical to real + translation table has associated with it a logical resource control + structure (3) (some of the contents of this control structure are defined + in the following text). The original logical resource control structures + (3) describe the standard logical resources allocated to the partition + due to the partition’s definition, such as one per Logical Memory + Blocks (LMB), etc. + The platform firmware, when creating the OF device tree for a given + partition knows the specific configuration of virtual IOAs with the + associated quantity of the various types of logical resources types for + each virtual IOA. From that knowledge, it understands the number and type + of resources that must be shared between the server and client partitions + and therefore the number of control structures that will be needed. When + an owning partition grants access to a subset of one of its logical + resources to another partition, the hypervisor chooses a logical resource + control structure to describe this newly granted resource (6), (as stated + above, the required number of these control structures were allocated + when the client virtual IOA was defined) and attaches it to the + grantee’s base partition control structure (5). This logical + resource control structure is linked (9) to the base logical resource + control structure (3) of the resource owner. Subsequently the + grantee’s OS may accept the shared logical resource (4) mapping it + (7) into the grantee’s partition logical to physical map table (8). + This same set of operations may subsequently be performed for other + partition(s) (10). The shared resource is always a subset (potentially + the complete subset) of the original. Once a partition (10) has accepted + a resource, it may subsequently grant a subset of that resource to yet + another partition (14), here the hypervisor creates a logical resource + control structure (13) links it (12) to the logical resource control + structure (11) of the granting partition (10) that is in turn linked (9) + to the owner’s logical resource control structure (3). +   +
+ Example Implementation of Control Structures + for Shared Logical Resources + + + + + + + + +
+ For the OS to return the logical resource represented by + control structure (11), the grant represented by control structure (13) + needs to be rescinded. This is normally accomplished only after the OS + that is running partition (14) performs a return operation, either + because it has finished using the logical resource, or in response to a + request (delivered by inter partition communications channel) from the + owner. The exceptions are in the case that either partition terminates + (the return operation is performed by the hypervisor) and a + non-responsive client (when the granter performs a forced rescind). A + return operation is much like a logical resource dynamic reconfiguration + isolate operation, the hypervisor removes the logical resource from the + partition’s logical to physical map table, to prevent new virtual + to physical mappings of the logical resource, then ensures that no + virtual to physical mappings of the logical resource are outstanding + (this can either be accomplished synchronously by checking map counts + etc. or asynchronously prior to the completion of the rescind operation. + + + + R1--1. + + + For the Shared Logical Resource option: The platform + must implement the hcall-logical-resource function set following the + syntax and semantics of the included hcall(s) as specified in: + , + , + , and + . + + + + + R1--2. + + + For the Shared Logical Resource option: In the event + that the partition owning a granted shared logical resource fails, the + platform must wait for a minimum of 2 seconds after notifying the client + partitions before recovering the shared resources via an automatic + H_RESCIND_LOGICAL (forced) operation. + + + + +
+ H_GRANT_LOGICAL + This hcall() creates a cookie that represents the specific instance + of the shared object. That is, the specific subset of the original + logical resource to be shared with the specific receiver partition. The + owning partition makes this hcall() in preparation for the sharing of the + logical resource subset with the receiver partition. The resulting cookie + is only valid for the specified receiver partition. + The caller needs to understand the bounds of the logical resource + being granted, such as for example, the logical address range of a given + LMB. The generated cookie does not span multiple elemental logical + resources (that is resources represented by their own Dynamic + Reconfiguration Connector). If the owner wishes to share a range of + resources that does span multiple elemental logical resources, then the + owner uses a series of H_GRANT_LOGICAL calls to generate a set of + cookies, one for each subset of each elemental logical resource to be + shared. + The “logical” parameter identifies the starting + “address” of the subset of the logical resource to be shared. + The form of this “address” is resource dependent, and is + given in + . + + + Syntax: + + + + + + + Parameters: +   + + Format of H_GRANT_LOGICAL parameters + + + + + + + + + + + Flags subfunction code (bits 16-23) + value: + + + + + + + + Access Restriction + + + Bits 16-19 + + + The defined bits in this field have + independent meanings, and may appear in combination with all + other bits unless specifically disallowed. (an x in the + binary field indicates that the bit can take on a value of 0 + or 1) + + + + + +   + + + 0b1xxx + + + Read access inhibited (The grantee may + not read from or grant access to read from this logical + resource.) + + + + +   + + + 0bx1xx + + + Write access inhibited (The grantee may + not write to or grant access to write to this logical + resource.) + + + + + +   + + + 0bxx1x + + + Re-Grant rights inhibited (the grantee + may not grant access to this logical resource to a subsequent + client.) + + + + + +   + + + 0bxxx1 + + + Reserved calling software should set + this bit to zero. Firmware returns H_Parameter if + set. + + + + + +   + + + + + + Logical Resource + + + + + Supported Combinations + + + + + Bits 20-23 + + + + + “address” + description + + + + + “length” + description + + + + + + System Memory + + + 0bxxx0 + + + 0x1 + + + Logical Address (as would be used in H_ENTER) in + logical-lo; logical-hi not used (should be = 0) + + + Bytes in units of 4 K on 4 K boundaries (low order 12 + bits = 0) + + + + + MMIO Space + + + 0bxxx0 + + + 0x2 + + + Logical Address (as would be used in H_ENTER) in + logical-lo; logical-hi not used (should be = 0) + + + Bytes in units of 4 K on 4 K boundaries (low order 12 + bits = 0) + + + + + Interrupt Source + + + 0b00x0 + + + 0x4 + + + 24 bit Interrupt # (as would be used in + ibm,get-xive) in low order 3 bytes in + logical-lo; logical-hi not used (should be = 0) + + + value=1 (the logical resource is one indivisible + unit) + + + + + DMA Window Pane + + Note: The DMA window only refers to physical DMA + windows not virtual DMA windows. Virtual DMA windows can be + directly created with a client virtual IOA definition and + need not be shared with those of the server. + + + + + 0b00x0 + + + 0x5 + + + 32 bit LIOBN in logical-hi; with a 64 bit IOBA + logical-lo + + + Bytes of IOBA in units of 4 K on 4 K boundaries (low + order 12 bits = 0) + + + + + Interprocessor Interrupt Port + + + 0b00x0 + + + 0x6 + + + Processor Number. (As from the processor’s Unit ID) + in logical-lo; logical-hi not used (should be = 0). + + + value=1 (the logical resource is one indivisible + unit) + + + + +
+ unit-address: The unit address of the virtual IOA associated with + the shared logical resource, and thus the partner partition that is to + share the logical resource. + + + + Semantics: + + + + Verify that the flags parameter specifies a supported logical + resource type, else return H_Parameter. + + + + Verify that the logical address validly identifies a logical + resource of the type specified by the flags parameter and owned/shared by + the calling partition, else return H_Parameter; unless: + + + + The logical address’s page number represents a page that + has been rescinded by the owner, then return H_RESCINDED. + + + + There exists a grant restriction on the logical resource, then + return H_Permission. + + + + + + Verify that the length parameter is of valid form for the + resource type specified by the flags parameter and that it represents a + subset (up to the full size) of the logical resource specified by the + logical address parameter, else return H_Parameter. + + + + Verify that the unit-address is for a virtual IOA owned by the + calling partition, else return H_Parameter. + + + + If the partner partition’s client virtual IOA has + sufficient resources, generate hypervisor structures to represent, for + hypervisor management purposes, including any grant restrictions, the + specified shared logical resource, else return H_NOMEM. + + + + Generate a cookie associated with the hypervisor structures + created in the previous step that the partner partition associated with + the unit-address can use to reference said structures via the + H_ACCEPT_LOGICAL and H_RETURN_LOGICAL hcall()s and the calling partition + can use to reference said structures via the H_RESCIND_LOGICAL + hcall(). + + + + Place the cookie generated in the previous step in R4 and return + H_Success. + + + +
+ +
+ H_RESCIND_LOGICAL + This hcall() invalidates a logical sharing as created by + H_GRANT_LOGICAL above. This operation may be subject to significant + delays in certain circumstances. Callers may experience an extended + series of H_PARTIAL returns prior to successful completion of this + operation. + If the sharer of the logical resource has not successfully + completed the H_RETURN_LOGICAL operation on the shared logical resource + represented by the specified cookie, the H_RESCIND_LOGICAL hcall() fails + with the H_Resource return code unless the “force” flag is + specified. The use of the “force” flag increases the + likelihood that a series of H_PARTIAL returns will be experienced prior + to successful completion. The “force” flag also causes the + hcall() to recursively rescind any and all cookies that represent + subsequent sharing of the logical resource. That is, if the original + client subsequently granted access to any or all of the logical resource + to a client, those cookies and any other subsequent grants are also + rescinded. + + + Syntax: + + + + + + + Parameters: + flags: The flags subfunction code field (bits 16-23) two values are + defined 0x00 “normal”, and 0x01 “forced”. + cookie: The handle returned by H_GRANT_LOGICAL representing the + logical resource to be rescinded. + + + + Semantics: + + + + Verify that the cookie parameter references an outstanding + instance of a shared logical resource owned/accepted by the calling + partition, else return H_Parameter. + + + + Verify that the flags parameter is one of the supported values, + else return H_Paramter. + + + + If the “force” flag is specified + Implementations should provide mechanisms to ensure that reserved + flag field bits are zero, to improve performance, implementations may + chose to activate this checking only in “debug” mode. The + mechanism for activating an implementation dependent debug mode is + outside of the scope of this architecture. + , then: perform the functions of H_RETURN_LOGICAL (cookie) as + if called by the client partition. Note this involves forced rescinding + any cookies generated by the client partition that refer to the logical + resource referenced by the original cookie being rescinded. + + + + If the client partition has the resource referenced by cookie is + in the available for mapping via its logical to physical mapping table + (the resource was accepted and not returned), return H_Resource. + + + + Verify that resource reference by cookie is not mapped by the + client partition, else return H_PARTIAL. + + + + Hypervisor reclaims control structures referenced by cookie and + returns H_Success. + + + +
+ +
+ H_ACCEPT_LOGICAL + The H_ACCEPT_LOGICAL hcall() maps the granted logical resource into + the client partition’s logical address space. To provide the most + compact client logical address space, the hypervisor maps the resource + into the lowest applicable logical address for the referenced logical + resource type, consistent with the resource’s size and the resource + type’s constraints upon alignment etc. The chosen logical address + for the starting point of the logical mapping is returned in register + R4. + + + Syntax: + + + + + + + Parameters: + cookie: The handle returned by H_GRANT_LOGICAL representing the + logical resource to be accepted. + + + + Semantics: + + + + Verify that the cookie parameter is valid for the calling + partition, else return H_Parameter. + n If the cookie represents a logical resources that has been + rescinded by the owner, return H_RESCINDED. + + + + Map the resources represented by the cookie parameter, with any + attendant access restrictions, into the lowest available logical address + of the calling partition consistent with constraints of size and + alignment and place the selected logical address into R4. + + + + Return H_Success. + + + +
+ +
+ H_RETURN_LOGICAL + The H_RETURN_LOGICAL hcall() unmaps the logical resource from the + client partition’s logical address space. Prior to calling + H_RETURN_LOGICAL the client partition should have destroyed all virtual + mappings to the section of the logical address space to which the logical + resource is mapped. That is unmapping virtual addresses for MMIO and + System Memory space, invalidating TCEs mapping a shared DMA window pane, + disabling/masking shared interrupt sources and/or inter processor + interrupts. Failing to do so, may result in parameter errors for other + hcall()s and H_Resource from the H_RETURN_LOGICAL hcall(). Part of the + semantic of this call is to determine that no such active mapping exists. + Implementations may be able to determine this quickly if they for example + maintain map counts for various logical resources, if an implementation + searches a significant amount of platform tables, then the hcall() may + return H_Busy and maintain internal state to continue the scan on + subsequent calls using the same cookie parameter. The cookie parameter + remains valid for the calling client partition until the server partition + successfully executes the H_RESCIND_LOGICAL hcall(). + + + Syntax: + + + + + + Parameters: + cookie: The handle returned by H_GRANT_LOGICAL representing the + logical resource to be returned. + + + + Semantics: + + + + Verify that the cookie parameter references an outstanding + instance of a shared logical resource accepted by the calling partition, + else return H_Parameter. + + + + Remove the referenced logical resource from the calling + partition’s logical address map. + + + + Verify that no virtual to logical mappings exist for the + referenced resource, else return H_Resource. + n This operation may require extensive processing -- in some cases + the hcall may return H_Busy to allow for improved system responsiveness + -- in these cases the state of the mapping scan is retained in the + hypervisor’s state structures such that after some number of + repeated calls the function is expected to finish. + + + + Return H_Success. + + + +
+ +
+ +
+ H_VIOCTL + The H_VIOCTL hypervisor call allows the partition to manipulate or + query certain virtual IOA behaviors. + +
+ Command Overview + + + Syntax: + + + + + + + Parameters: + + + + unit-address: As specified. + + + + subfunction: Specific subfunction to perform; see + . + + + + parm-1: Specified in subfunction semantics. + + + + parm-2: Specified in subfunction semantics. + + + + parm-3: Specified in subfunction semantics. + + + + + + Semantics: + + + + Validate that the subfunction is implemented, else return + H_Not_Found. + + + + Validate the unit-address, else return H_Parameter. + + + + Validate the subfunction is valid for the given virtual IOA, else + return H_Parameter. + + + + Refer to + to determine the semantics for + the given subfunction. + + + +   + + Semantics for H_VIOCTL subfunction parameter values + + + + + + + + + + Subfunction Number + + + + + Subfunction Name + + + + + Required? + + + + + Semantics Defined in + + + + + + + + 0x0 + + + (Reserved) + + + (Reserved) + + + (Reserved) + + + + + 0x1 + + + GET_VIOA_DUMP_SIZE + + + For all VIO options + + + + . + + + + + 0x2 + + + GET_VIOA_DUMP + + + + . + + + + + 0x3 + + + GET_ILLAN_NUMBER_VLAN_IDS + + + For the ILLAN option + + + + . + + + + + 0x4 + + + GET_ILLAN_VLAN_ID_LIST + + + + . + + + + + 0x5 + + + GET_ILLAN_SWITCH_ID + + + For the ILLAN option + + + + + + + + + + 0x6 + + + DISABLE_MIGRATION + + + For all vscsi-server and vfc-server + + + + . + + + + + 0x7 + + + ENABLE_MIGRATION + + + + . + + + + + 0x8 + + + GET_PARTNER_INFO + + + + . + + + + + 0x9 + + + GET_PARTNER_WWPN_LIST + + + For all vfc-server + + + + . + + + + + 0xA + + + DISABLE_ALL_VIO_INTERRUPTS + + + For the Subordinate CRQ Transport option + + + + + + + + + + 0xB + + + DISABLE_VIO_INTERRUPT + + + + + + + + + + 0xC + + + ENABLE_VIO_INTERRUPT + + + + + + + + + + 0xD + + + GET_ILLAN_MAX_VLAN_PRIORITY + + + No + + + + + + + + + + 0xE + + + GET_ILLAN_NUMBER_MAC_ACLS + + + No + + + + + + + + + + 0xF + + + GET_MAC_ACLS + + + No + + + + + + + + + + 0x10 + + + GET_PARTNER_UUID + + + For UUID Option + + + + + + + + + + 0x11 + + + FW_RESET + + + For the VNIC option. + + + + + + + + + + 0x12 + + + Get_ILLAN_SWITCHING_MODE + + + For any ILLAN adapter with the + “ibm,trunk-adapter” property + + +   + + + + + 0x13 + + + DISABLE_INACTIVE_TRUNK_RECEPTION + + + For any ILLAN adapter with the + "ibm,trunk-adapter" property + + + + + + + + + +
+ +
+ +
+ GET_VIOA_DUMP_SIZE Subfunction Semantics + + + + Validate parm-1, parm-2, and parm-3 are set to zero, else return + H_Parameter. + + + + The hypervisor calculates the size necessary for passing opaque + firmware data describing current virtual IOA state to the partition for + purposes of error logging and RAS, and returns H_Success, with the + required size in R4. + + +
+ +
+ GET_VIOA_DUMP Subfunction Semantics + + + + If the given virtual IOA has an + “ibm,my-dma-window” property in its + device tree, then parm-1 is an eight byte output descriptor. The high + order byte of an output descriptor is control, the next three bytes are a + length field of the buffer in bytes, and the low order four bytes are a + TCE mapped I/O address of the start of a buffer in I/O address space. The + high order control byte must be set to zero. The TCE mapped I/O address + is mapped via the first window pane of the + “ibm,my-dma-window” property. + + + + If the given virtual IOA has no + “ibm,my-dma-window” property in its + device tree, then parm-1 shall be a logical real, page-aligned address of + a 4 K page used to return the virtual IOA dump. + + + + Validate parm-2 and parm-3 are set to zero, else return + H_Parameter. + + + + If parm-1 is an output descriptor, then + + + + n Validate the I/O address range is in the required DMA window and + is mapped by valid TCEs, else return H_Parameter. + + + + Transfer as much opaque hypervisor data as fits into the output + buffer as specified by the output descriptor. + + + + If all opaque data will not fit due to size, return + H_Constrained, else return H_Success. + + + + + + If parm-1 is a logical real address, then + + + + Validate the logical real address is valid for the partition, + else return H_Parameter. + + + + Transfer as much opaque hypervisor data as will fit into the + passed logical real page, with a maximum of 4 K. + + + + If all opaque data will not fit in the page due to size, return + H_Constrained, else return H_Success. + + + + +
+ +
+ GET_ILLAN_NUMBER_VLAN_IDS Subfunction Semantics + + + + Validate parm-1, parm-2, and parm-3 are set to zero, else return + H_Parameter. + + + + The hypervisor returns H_Success, with the number of VLAN IDs + (PVID + VIDs) in R4. This subfunction allows the partition to allocate + the correct amount of space for the call: + H_VIOCTL(GET_VLAN_ID_LIST). + + +
+ +
+ GET_ILLAN_VLAN_ID_LIST Subfunction Semantics + + + + parm-1 is an eight byte output descriptor. The high order byte of + an output descriptor is control, the next three bytes are a length field + of the buffer in bytes, and the low order four bytes are a TCE mapped I/O + address of the start of a buffer in I/O address space. The high order + control byte must be set to zero. The TCE mapped I/O address is mapped + via the first window pane of the + “ibm,my-dma-window” property. + + + + Validate parm-2 and parm-3 are set to zero, else return + H_Parameter. + + + + Validate the I/O address range is in the required DMA window and + is mapped by valid TCEs, else return H_Parameter. + + + + Transfer the VLAN_ID_LIST into the output buffer as specified by + the output descriptor. The data will be an array of two byte values, + where the first element of the array is the PVID followed by all the + VIDs. The format of the elements of the array is specified by IEEE VLAN + documentation. Any unused space in the output buffer will be + zeroed. + + + + If all VLAN IDs do not fit due to size, return + H_Constrained. + + + + Return H_Success + + +
+ +
+ GET_ILLAN_SWITCH_ID Subfunction Semantics + + + + parm-1 is an eight byte output descriptor. The high order byte of + an output descriptor is control, the next three bytes are a length field + of the buffer in bytes, and the low order four bytes are a TCE mapped I/O + address of the start of a buffer in I/O address space. The high order + control byte must be set to zero. The TCE mapped I/O address is mapped + via the first window pane of the + “ibm,my-dma-window” property. + + + + Validate parm-2 and parm-3 are set to zero, else return + H_Parameter. + + + + Validate the I/O address range is in the required DMA window and + is mapped by valid TCEs, else return H_Parameter. + + + + Transfer the GET_ILLAN_SWITCH_ID into the output buffer as + specified by the output descriptor. The data will be a string of ASCII + characters uniquely identifying the virtual switch to which the ILLAN + adapter is connected. Any unused space in the output buffer will be + zeroed. + + + + If the switch identifier does not fit due to size, return + H_Constrained. + + + + Return H_Success + + +
+ +
+ DISABLE_MIGRATION Subfunction Semantics + When this subfunction is implemented, the + “ibm,migration-control” property exists + in the + /vdevice OF device tree node. + + + + Validate that parm-1, parm-2, and parm-3 are all set to zero, + else return H_Parameter. + + + + If no partner is connected, then return H_Closed. + + + + Prevent the migration of the partner partition to the destination + server until either the ENABLE_MIGRATION subfunction is called or + H_FREE_CRQ is called. + + + + Return H_Success. + + +
+ +
+ ENABLE_MIGRATION Subfunction Semantics + When this subfunction is implemented, the + “ibm,migration-control” property exists + in the + /vdevice OF device tree node. + + + + Validate that parm-1, parm-2, and parm-3 are all set to zero, + else return H_Parameter. + + + + Validate that the migration of the partner partition to the + destination server was previously prevented with DISABLE_MIGRATION + subfunction, else return H_Parameter. + + + + Enable the migration of the partner partition. + + + + Return H_Success. + + +
+ +
+ GET_PARTNER_INFO Subfunction Semantics + + + + Parm-1 is an eight byte output descriptor. The high order byte of + an output descriptor is control, the next three bytes are a length field + of the buffer in bytes, and the low order four bytes are a TCE mapped I/O + address of the start of a buffer in I/O address space. The high order + control byte must be set to zero. The TCE mapped I/O address is mapped + via the first window pane of the + “ibm,my-dma-window” property. + + + + Validate parm-2 and parm-3 are set to zero, else return + H_Parameter. + + + + Validate the I/O address range is in the required DMA window and + is mapped by valid TCEs, else return H_Parameter. + + + + If the output buffer is not large enough to fit all the data, + then return H_Constrained. + + + + If no partner is connected and more than one possible partner + exists, then return H_Closed. + + + + Transfer the eight byte partner partition ID into the first eight + bytes of the output buffer. + + + + Transfer the eight byte unit address into the second eight bytes + of the output buffer. + + + + Transfer the NULL-terminated Converged Location Code associated + with the partner unit address and partner partition ID immediately + following the unit address. + + + + Zero any remaining output buffer. + + + + Return H_Success. + + +
+ +
+ GET_PARTNER_WWPN_LIST Subfunction Semantics + This subfunction is used to get the WWPNs for the partner from the + hypervisor. In this way, there is assurance that the WWPNs are + accurate. + + + + Parm-1 is an eight byte output descriptor. The high order byte of + an output descriptor is control, the next three bytes are a length field + of the buffer in bytes, and the low order four bytes are a TCE mapped I/O + address of the start of a buffer in I/O address space. The high order + control byte must be set to zero. The TCE mapped I/O address is mapped + via the first window pane of the + “ibm,my-dma-window” property. + + + + Validate parm-2 and parm-3 are set to zero, else return + H_Parameter. + + + + Validate the I/O address range is in the required DMA window and + is mapped by valid TCEs, else return H_Parameter. + + + + If the output buffer is not large enough to fit all the data, + return H_Constrained. + + + + If no partner is connected, return H_Closed. + + + + Transfer the first eight byte WWPN, which is represented in the + vfc-client node of the partner partition in the + “ibm,port-wwn-1” parameter, into the + first eight bytes of the output buffer. + + + + Transfer the second eight byte WWPN, which is represented in the + vfc-client node of the partner partition in the + “ibm,port-wwn-2” parameter, into the + second eight bytes of the output buffer. + + + + Zero any remaining output buffer. + + + + Return H_Success. + + +
+ +
+ DISABLE_ALL_VIO_INTERRUPTS Subfunction + Semantics + This subfunction is used to disable any and all the CRQ and Sub-CRQ + interrupts associated with the virtual IOA designated by the + unit-address, for VIOs that define the use of Sub-CRQs. Software that + controls a virtual IOA that does not define the use of Sub-CRQ facilities + should use the H_VIO_SIGNAL hcall() to disable CRQ interrupts. + + Programming Note: On platforms that implement the + partition migration option, after partition migration the support for + this subfunction might change, and the caller should be prepared to + receive an H_Not_Found return code indicating the platform does not + implement this subfunction. + + + + Validate parm-1, parm-2, and parm-3 are set to zero, else return + H_Parameter. + + + + Disable all CRQ and any Sub-CRQ interrupts associated with + unit-address. + + + + Return H_Success. + + +
+ +
+ DISABLE_VIO_INTERRUPT Subfunction Semantics + This subfunction is used to disable a CRQ or Sub-CRQ interrupt, for + VIOs that define the use of Sub-CRQs. The CRQ or Sub-CRQ is defined by + the unit-address and parm-1. Software that controls a virtual IOA that + does not define the use of Sub-CRQ facilities should use the H_VIO_SIGNAL + hcall() to disable CRQ interrupts. + + Programming Note: On platforms that implement the + partition migration option, after partition migration the support for + this subfunction might change, and the caller should be prepared to + receive an H_Not_Found return code indicating the platform does not + implement this subfunction. + + + + Parm-1 is the interrupt number of the interrupt to be disabled. + For an interrupt associated with a CRQ this number is obtained from the + “interrupts” property in the device tree + For an interrupt associated with a Sub-CRQ this number is obtained during + the registration of the Sub-CRQ (H_REG_SUB_CRQ). + + + + Validate parm-1 is a valid interrupt number for a CRQ or Sub-CRQ + for the virtual IOA defined by parm-1 and that parm-2 and parm-3 are set + to zero, else return H_Parameter. + + + + Disable interrupt specified by parm-1. + + + + Return H_Success. + + +
+ +
+ ENABLE_VIO_INTERRUPT Subfunction Semantics + This subfunction is used to enable a CRQ or Sub-CRQ interrupt, for + VIOs that define the use of Sub-CRQs. The CRQ or Sub-CRQ is defined by + the unit-address and parm-1. Software that controls a virtual IOA that + does not define the use of Sub-CRQ facilities should use the H_VIO_SIGNAL + hcall() to disable CRQ interrupts. + + Programming Note: On platforms that implement the + partition migration option, after partition migration the support for + this subfunction might change, and the caller should be prepared to + receive an H_Not_Found return code indicating the platform does not + implement this subfunction. + + + + Parm-1 is the interrupt number of the interrupt to be enabled. + For an interrupt associated with a CRQ this number is obtained from the + “interrupts” property in the device tree + For an interrupt associated with a Sub-CRQ this number is obtained during + the registration of the Sub-CRQ (H_REG_SUB_CRQ). + + + + Validate parm-1 is a valid interrupt number for a CRQ or Sub-CRQ + for the virtual IOA defined by unit-address and that parm-2 and parm-3 + are set to zero, else return H_Parameter. + + + + Enable interrupt specified by parm-1. + + + + Return H_Success. + + +
+ +
+ GET_ILLAN_MAX_VLAN_PRIORITY Subfunction Semantics + + + + Validate parm-1, parm-2, and parm-3 are set to zero, else return + H_Parameter. + + + + The hypervisor returns H_Success, with the maximum IEEE 802.1Q + VLAN priority returned in R4. If no priority limits are in place, the + maximum VLAN priority is returned in R4. + + +
+ +
+ GET_ILLAN_NUMBER_MAC_ACLS Subfunction Semantics + This subfunction allows the partition to allocate the correct + amount of space for the GET_MAC_ACLS Subfunction call. + + + + Validate parm-1, parm-2, and parm-3 are set to zero, else return + H_Parameter. + + + + The hypervisor returns H_Success, with the number of allowed MAC + addresses returned in R4. If no MAC access control limits are in place, 0 + is returned in R4. + + +
+ +
+ GET_MAC_ACLS Subfunction Semantics + + + + parm-1 is an eight byte output descriptor. The high order byte of + an output descriptor is control, the next three bytes are a length field + of the buffer in bytes, and the low order four bytes are a TCE mapped I/O + address of the start of a buffer in I/O address space. The high order + control byte must be set to zero. The TCE mapped I/O address is mapped + via the first window pane of the + “ibm,my-dma-window” property. + + + + Validate parm-2 and parm-3 are set to zero, else return + H_Parameter. + + + + Validate the I/O address range is in the required DMA window and + is mapped by valid TCEs, else return H_Parameter. + + + + Transfer the allowed MAC addresses into the output buffer as + specified by the output descriptor. The data will be an array of 8 byte + values containing the allowed MAC address, with the low order 6 bytes + containing the 6 byte MAC address. Any unused space in the output buffer + are zeroed. + + + + If all allowed MAC addresses do not fit due to size, return + H_Constrained. + + + + Return H_Success + + +
+ +
+ GET_PARTNER_UUID Subfunction Semantics + + + + Validate parm-1, parm-2 and parm-3 are set to zero, else return + H_Parameter. + + + + If no partner is connected and more than one possible partner + exists, then return H_Closed. + + + + Transfer into registers R4 (High order 8 bytes) and R5 (low order + 8 bytes) of the UUID of the client partition that owns the virtual device + ( + for the format of the UUID string. + + + + Return H_Success + + +
+ +
+ FW_Reset Subfunction Semantics + This H_VIOCTL subfunction will reset the VNIC firmware associated + with a VNIC client adapter, if currently active. This subfunction is + useful when the associated firmware becomes unresponsive to other + CRQ-based commands. For the case of vTPMs the firmware will be left + inoperable until the client partition next boots up. + + + Semantics: + + + + Validate that parm-1, parm-2, and parm-3 are all set to zero, + else return H_Parameter. + + + + If the firmware associated with the virtual adapter can not be + reset, return H_Constrained. + + + + Reset the firmware associated with the virtual adapter. + + + + Return H_Success. + + + +
+ +
+ GET_ILLAN_SWITCHING_MODE Subfunction Semantics + + + + Validate parm-1, parm-2, and parm-3 are set to zero, else return + H_Parameter. + + + + Validate that the given virtual IOA is a ILLAN adapter with the + "ibm,trunk-adapter", else return H_Parameter. + + + + The hypervisor returns H_Success, with the current switching mode + in R4. If the switching mode is VEB mode, R4 will have a 0. If the + switching mode is VEPA mode, R4 will have a 1. + + +
+ +
+ DISABLE_INACTIVE_TRUNK_RECEPTION Subfunction + Semantics: + This subfunction is used to disable the reception of all packets + for a ILLAN trunk adapter that is not the Active Trunk Adapter as set by + the H_ILLAN_ATTRIBUTES hcall. + + Note: The default value for this attribute is + ENABLED. The value is reset on a successful H_FREE_LOGICAL_LAN hcall or + reboot/power change of the partition owning the ILLAN adapter. + + + + Validate parm-1, parm-2, and parm-3 are set to zero, else return + H_Parameter. + + + + Validate that the given virtual IOA is a ILLAN adapter with the + "ibm,trunk-adapter", else return H_Parameter. + + + + The hypervisor disables reception of packets for this adapter + when it is not the Active Trunk Adapter. + + + + Return H_Success. + + +
+
+ +
+ +
+ Partition Managed Class Infrastructure - General + In addition to the general requirements for all VIO described in + , the architecture for the + partition managed class of VIO defines several other + infrastructures: + + + + + A Command/Response Queue (CRQ) that allows communications back + and forth between the server partition and its partner partition (see + ). + + + + A Subordinate CRQ (Sub-CRQ) facility that may be used in + conjunction with the CRQ facility, when the CRQ facility by itself is not + sufficient. That is, when more than one queue with more than one + interrupt is required by the virtual IOA. See + . + + + + A mechanism for doing RDMA, which includes: + + + + A mechanism called Copy RDMA that can be used by the device + driver to move blocks of data between memory of the server and partner + partitions + + + + A mechanism for Redirected RDMA that allows the device driver to + direct DMA of data from the server partition’s physical IOA to or + from the partner partition’s memory (see + ). + + + + + + The mechanisms for the synchronous type VIO are described as + follows: + + + + + + + +   + +
+ Command/Response Queue (CRQ) + The CRQ facility provides ordered delivery of messages between + authorized partitions. The facility is reliable in the sense that the + messages are delivered in sequence, that the sender of a message is + notified if the transport facility is unable to deliver the message to + the receiver’s queue, and that a notification message is delivered + (providing that there is free space on the receive queue), or if the + partner partition either fails or deregisters its half of the transport + connection. The CRQ facility does not police the contents of the payload + portions (after the 1 byte header) of messages that are exchanged between + the communicating pairs, however, this architecture does provide means + (via the Format Byte) for self describing messages such that the + definitions of the content and protocol between using pairs may evolve + over time without change to the CRQ architecture, or its + implementation. + The CRQ is used to hold received messages from the partner + partition. The CRQ owner may optionally choose to be notified via an + interrupt when a message is added to their queue. + +
+ CRQ Format and Registration + The CRQ is built of one or more 4 KB pages aligned on a 4 KB + boundary within partition memory. The queue is organized as a circular + buffer of 16 byte long elements. The queue is mapped into contiguous I/O + addresses via the TCE mechanism and RTCE table (first window pane). The + I/O address and length of the queue are registered by + . This registration process + tells the hypervisor where to find the virtual IOA’s CRQ. +
+ +
+ CRQ Entry Format + Each CRQ entry consists of a 16 byte element. The first byte of a + CRQ entry is the Header byte and is defined in + . +   + + CRQ Entry Header Byte Values + + + + + + + + + Header Value + + + + + Description + + + + + + + + 0 + + + Element is unused -- all other bytes in the element are + undefined + + + + + 0x01 - 0x7F + + + Reserved + + + + + 0x80 + + + Valid Command/Response entry -- the second byte defines + the entry format (for example, see + ). + + + + + 0x81 - 0xBF + + + Reserved + + + + + 0xC0 + + + Valid Initialization Command/Response entry -- the second + byte defines the entry format. See + . + + + + + 0xC1 - 0xFE + + + Reserved + + + + + 0xFF + + + Valid Transport Event -- the second byte defines the + specific transport event. See + . + + + + +
+ The platform (transport mechanism) ignores the contents of all + non-header bytes in all CRQ entries. + Valid Command/Response entries (Header byte 0x80) are used to carry + data between communicating partners, transparently to the platform. The + second byte of the entry is reserved for a Format byte to enable the + definitions of the content and protocol between using pairs to evolve + over time. The definition of the second byte of the Valid + Command/Response entry is beyond the scope of this architecture. + presents example VSCSI format + byte values. + The Valid Initialization Command/Response entry (Header byte 0xC0) + is used during virtual IOA initialization sequences. The second byte of + this type entry is architected and is as defined in + . This format is used for + initialization operations between communicating partitions. The remaining + bytes (byte three and beyond) of the Valid Initialization + Command/Response entry are available for definition by the communicating + entities. +   + + Initialization Command/Response Entry Format Byte + Definitions + + + + + + + + + Format Byte Value + + + + + Definition + + + + + + + + 0x0 + + + Unused + + + + + 0x1 + + + Initialize + + + + + 0x2 + + + Initialization Complete + + + + + 0x03 - 0xFE + + + Reserved + + + + + 0xFF + + + Reserved for Expansion + + + + +
+ Valid Transport Events (Header byte 0xFF) are used by the platform + to notify communicating partners of conditions associated with the + transport channel, such as the failure of the partner’s partition + or the deregistration of the partner’s queue. The partner’s + queue may be deregistered as a means of resetting the transport channel + or simply to terminate the connection. When the Header byte of the queue + entry specifies a Valid Transport Event, then the second byte of the CRQ + entry defines the type of transport event. The Format byte (second byte) + of a Valid Transport Event queue entry is architected and is as defined + in + ). +   + + Transport Event Codes + + + + + + + + + Code Value + + + + + Explanation + + + + + + + + 0 + + + Unused + + + + + 1 + + + Partner partition failed + + + + + 2 + + + Partner partition deregistered CRQ + + + + + 3 + + +   + + + + + 4 + + +   + + + + + 5 + + +   + + + + + 6 + + + Partner partition suspended (for the Partition Suspension + option) + + + + + 0x07 - 0xFF + + + Reserved + + + + +
+ The “partner partition suspended” transport event + disables the associated CRQ such that any H_SEND_CRQ hcall() ( + ) to the associated CRQ returns + H_Closed until the CRQ has been explicitly enabled using the H_ENABLE_CRQ + hcall (See + ). +
+ +
+ CRQ Entry Processing + Prior to the partition software registering the CRQ, the partition + software sets all the header bytes to zero (entry invalid). After + registration, the first valid entry is placed in the first element and + the process proceeds to the end of the queue and then wraps around to the + first entry again (given that the entry has been subsequently marked as + invalid). This allows both the partition software and transport firmware + to maintain independent pointers to the next element they will be + respectively using. + A sender uses an infrastructure dependent method to enter a 16 byte + message on its partner’s queue (see + ). Prior to enqueueing an entry + on the CRQ, the platform first checks if the session to the + partner’s queue is open, and there is a free entry, if not, it + returns an error. If the checks succeed, the contents of the message is + copied into the next free queue element, potentially notifying the + receiver, and returns a successful status to the caller. + At the receiver’s option, it may be notified via an interrupt + when an element is enqueued to its CRQ. See + . + When the receiver has finished processing a queue entry, it writes + the header to the value 0x00 to invalidate the entry and free it for + future entries. + Should the receiver wish to terminate or reset the communication + channel it deregisters the queue, and if it needs to re-establish + communications, proceeds to register either the same or different section + of memory as the new queue, with the queue pointers reset to the first + entry. +
+ +
+ CRQ Facility Interrupt Notification + The receiver can set the virtual interrupt associated with its CRQ + to one of two modes. These are: + + + + Disabled (An enqueue interrupt is not signaled.) + + + + Enabled (An enqueue interrupt is signaled on every + enqueue) + + + + Note: An enqueue is considered a pulse not a level. + The pulse then sets the memory element within the emulated interrupt + source controller. This allows the resetting of the interrupt condition + by simply issuing the H_EOI hcall() as is done with the PCI MSI + architecture rather than having to do an explicit interrupt reset as in + the case with PCI Level Sensitive Interrupt (LSI) architecture. + The interrupt mechanism is capable of presenting only one interrupt + signal at a time from any given interrupt source. Therefore, no + additional interrupts from a given source are ever signaled until the + previous interrupt has been processed through to the issuance of an H_EOI + hcall(). Specifically, even if the interrupt mode is enabled, the effect + is to interrupt on an empty to non-empty transition of the queue. + However, as with any asynchronous posting operation race conditions are + to be expected. That is, an enqueue can happen in a window around the + H_EOI hcall(). Therefore, the receiver should poll the CRQ after an H_EOI + to prevent losing initiative. + See ) for + information about interrupt control. +
+ +
+ Extensions to Other hcall()s for CRQ + + +
+ H_MIGRATE_DMA + Since the CRQ is RTCE table mapped, the H_MIGRATE_DMA hcall() may + be requested to move a page that is part of the CRQ. The OS owner of the + queue is responsible for preventing its processors from modifying the + page during the migrate operation (as is standard practice with this + hcall()), however, the H_MIGRATE_DMA hcall() serializes with the CRQ + hcall()s to direct new elements to the migrated target page. +
+ +
+ H_XIRR, H_EOI + The CRQ facility utilizes a virtual interrupt source number to + notify the queue owner of new element enqueues. The standard H_XIRR and + H_EOI hcall()s are extended to support this virtual interrupt mechanism, + emulating the standard PowerPC Interrupt hardware with respect to the + virtual interrupt source number. +
+
+
+ CRQ Facility Requirements + + + + R1--1. + + For the CRQ facility: The platform must implement the + CRQ as specified in + . + + + + + R1--2. + + For the CRQ facility: The platform must reject CRQ + definitions that are not 4 KB aligned. + + + + + R1--3. + + For the CRQ facility: The platform must reject CRQ + definitions that are not a multiple of 4 KB long. + + + + + R1--4. + + For the CRQ facility: The platform must reject CRQ + definitions that are not mapped relative to the TCE mapping defined by + the first window pane of the virtual IOA’s + “ibm,my-dma-window” property. + + + + + R1--5. + + For the CRQ facility: + The platform must + start enqueueing Commands/Responses to the newly registered CRQ starting + at offset zero and proceeding as in a circular buffer, each entry being + 16 byte aligned. + + + + + R1--6. + + For the CRQ facility: + The platform must + enqueue Commands/Responses only if the 16 byte entry is free (header byte + contains 0x00), else the enqueue operation fails. + + + + + R1--7. + + For the CRQ facility: The platform must enqueue the + 16 bytes specified in the validated enqueue request as specified in + Requirement + except as required by + Requirement + . + + + + + R1--8. + + For the CRQ facility: + The platform must + not enqueue commands/response entries if the CRQ has not been registered + successfully or if after a successful completion, has subsequently + deregistered the CRQ. + + + + + R1--9. + + For the CRQ facility: The platform (transport + mechanism) must ignore and must not modify the contents of all non-header + bytes in all CRQ entries. + + + + + R1--10. + + For the CRQ facility: The first byte of a CRQ entry + must be the Header byte and must be as defined in + . + + + + + R1--11. + + For the CRQ facility: The Format byte (second byte) + of a Valid Initialization CRQ entry must be as defined in + . + + + + + R1--12. + + For the CRQ facility: The Format byte (second byte) + of a Valid Transport Event queue entry must be as defined in + . + + + + + R1--13. + + For the CRQ facility: If the partner partition fails, + then the platform must enqueue a 16 byte entry starting with 0xFF01 (last + 14 bytes unspecified) as specified in Requirement + except as required by + Requirements + and + . + + + + + R1--14. + + For the CRQ facility: If the partner partition + deregisters its corresponding CRQ, then the platform must enqueue a 16 + byte entry starting with 0xFF02 (last 14 bytes unspecified) as specified + in Requirement + except as required by + Requirements + and + . + + + + + R1--15. + + + Reserved + + + + + R1--16. + + For the CRQ facility with the Partner Control + option: If the partner partition is terminated by request of + this partition via the + ibm,partner-control RTAS call, then the platform must + enqueue a 16 byte entry starting with 0xFF04 (last 14 bytes unspecified) + as specified in Requirement + except as required by + Requirements + and + when the partner partition has + been successfully terminated. + + + + + R1--17. + + + Reserved + + + + + R1--18. + + For the CRQ facility option: Platforms that implement + the H_MIGRATE_DMA hcall() must implement that function for pages mapped + for use by the CRQ. + + + + + R1--19. + + For the CRQ facility: The platforms must emulate the + standard PowerPC External Interrupt Architecture for the interrupt source + numbers associated with the virtual devices via the standard RTAS and + hypervisor interrupt calls and must extend H_XIRR and H_EOI hcall()s as + appropriate for CRQ interrupts. + + + + + R1--20. + + For the CRQ facility: The platform’s OF must + disable interrupts from the using virtual IOA before initially passing + control to the booted partition program. + + + + + R1--21. + + For the CRQ facility: The platform’s OF must + disable interrupts from the using virtual IOA upon registering the + IOA’s CRQ. + + + + + R1--22. + + For the CRQ facility: The platform’s OF must + disable interrupts from the using virtual IOA upon deregistering the + IOA’s CRQ. + + + + + R1--23. + + For the CRQ facility: The platform must present (as + appropriate per RTAS control of the interrupt source number) the + partition owning a CRQ the appearance of an interrupt, from the interrupt + source number associated, through the OF device tree node, with the + virtual device, when a new entry is enqueued to the virtual + device’s CRQ and when the last interrupt mode set was + “Enabled”, unless a previous interrupt from the interrupt + source number is still outstanding. + + + + + R1--24. + + For the CRQ facility: The platform must not present + the partition owning a CRQ the appearance of an interrupt, from the + interrupt source number associated, through the OF device tree node, with + the virtual device, if the last interrupt mode set was + “Disabled”, unless a previous interrupt from the interrupt + source number is still outstanding. + + + +
+
+ +
+ Redirected RDMA (Using H_PUT_RTCE, and + H_PUT_RTCE_INDIRECT) + A server partition uses the hypervisor function, H_PUT_RTCE, which + takes as a parameter the opaque handle (LIOBN) of the partner + partition’s RTCE table (second window pane of + “ibm,my-dma-window”), an offset in the + RTCE table, the handle for one of the server partition's I/O adapter TCE + tables plus an offset within the I/O adapter's TCE table. H_PUT_RTCE then + copies the appropriate contents of the partner partition's RTCE table + into the server partition's I/O adapter TCE table. In effect, this + hcall() allows the server partition's I/O adapter to have access to a + specific section of the partner partition's memory as if it were the + server partition's memory. However, the partner partition, through the + hypervisor, maintains control over exactly which areas of the partner + partition's memory are made available to the server partition without the + overhead of the hypervisor having to directly handle each byte of the + shared data. + The H_PUT_RTCE_INDIRECT, if implemented, takes as an input + parameter a pointer to a list of offsets into the RTCE table, and builds + the TCEs similar to the H_PUT_RTCE, described above. + A server partition uses the hypervisor function, H_REMOVE_RTCE, to + back-out TCEs generated by the H_PUT_RTCE and H_PUT_RTCE_INDIRECT + hcall()s. + The following rules guide the definition of the RTCE table entries + and implementation of the H_PUT_RTCE, H_PUT_RTCE_INDIRECT, H_REMOVE_RTCE, + H_MASS_MAP_TCE, H_PUT_TCE, H_PUT_TCE_INDIRECT, and H_STUFF_TCE hcall()s. + Other implementations that provide the same external appearance as these + rules are acceptable. The architectural intent is to provide RDMA + performance essentially equivalent to direct TCE operations. + + + + The partner partition's RTCE table is itself never directly + accessed by an I/O Adapter (IOA), it is only accessed by the hypervisor, + and therefore it can be a bigger structure than the regular TCE table as + accessed by hardware (more fields). + + + + When a server partition asks (via an H_PUT_RTCE or + H_PUT_RTCE_INDIRECT hcall()) to have an RTCE table TCE copied to one of + the server partition's physical IOA's TCEs, or asks (via an + H_REMOVE_RTCE) to have an RTCE table entry removed from one of the server + partition’s physical IOA’s TCEs, the hypervisor atomically, + with respect to all RTCE table readers, sets (H_PUT_RTCE or + H_PUT_RTCE_INDIRECT) or removes (H_REMOVE_RTCE) a field in the copied + RTCE table entry + This is an example of where the earlier statement “Other + implementations that provide the same external appearance as these + rules are acceptable” comes into affect. For example, for an RTCE + table that is mapped with H_MASS_MAP_TCE, the pointer may not be in a + field of the actual TCE in the RTCE table, but could, for example, be + in a linked list, or other such structure, due to the fact that there + is not a one-to-one correspondence from the RTCE to the physical IOA + TCE in that case (H_MASS_MAP_TCE can map up to an LMB into one TCE, and + physical IOA TCEs only map 4 KB). + . This field is a pointer to the copy of the RTCE table TCE in + the server partition’s IOA’s TCE table. (A per RTCE table TCE + lock is one method for the atomic setting of the copied RTCE table TCE + link pointer.) + + + + If a server partition tries to get another copy of the same RTCE + table TCE it gets an error return (multiple mappings of the same physical + page are allowed, they just need to use different RTCE table TCEs just + like with physical IOA TCEs). + + + + When the partner partition issues an H_PUT_TCE, + H_PUT_TCE_INDIRECT, H_STUFF_TCE, or H_MASS_MAP hcall() to change his RTCE + table, the hypervisor finds the TCE tables in one of several states. A + number of these states represent unusual conditions, that can arise from + timing windows or error conditions. The hypervisor rules for handling + these cases are chosen to minimize its overhead while preventing one + partition’s errors from corrupting another partition’s + state. + + + + The RTCE table TCE is not currently in use: Clear/invalidate the + TCE copy pointer and enter the RTCE table TCE mapping per the input + parameters to the hcall(). + + + + The RTCE table TCE contains a valid mapping and the TCE copy + pointer is invalid (NULL or other implementation dependent value) (The + previous mapping was never used for Redirected RDMA): Enter the RTCE + table TCE mapping per the input parameters to the hcall(). + + + + The RTCE table TCE contains a valid mapping and the TCE copy + pointer references a TCE that does not contain a valid copy of the + previous mapping in the RTCE table TCE. (The previous mapping was used + for Redirected RDMA, however, the server partition has moved on and is no + longer targeting the page represented by the old RTCE table TCE mapping): + Clear/invalidate the TCE copy pointer and enter the RTCE table TCE + mapping per the input parameters to the hcall(). + + + + The RTCE table TCE contains a valid mapping and the TCE copy + pointer references a TCE that does contain a valid copy of the previous + mapping in the RTCE table TCE (the previous mapping is still potentially + in use for Redirected RDMA, however, the partner partition has moved on + and is no longer interested in the previous I/O operation). The server + partition’s IOA may still target a DMA operation against the TCE + containing the copy of the RTCE table TCE mapping. The assumption is that + any such targeting is the result of a timing window in the recovery of + resources in the face of errors. Therefore, the server partition’s + TCE is considered invalid, but the server partition may or may not be + able to immediately invalidate the TCEs. For more information on + invalidation of TCEs, see + . The H_Resource return from an + H_PUT_TCE, H_PUT_TCE_INDIRECT, and H_STUFF_TCE may be used to hold off + invalidation in this case. + + + + + + If a server partition terminates, the partner partition’s + device drivers time out the operations and resource recovery code + recovers the RTCE table TCEs. If the partner partition terminates, the + hypervisor scans the RTCE table and eventually invalidates all active + copies of RTCE table TCEs. For more information on invalidation of TCEs, + see . + + + + The server partition may use any of the supported hcall()s (see + ) to manage the TCE tables used + by its IOAs. No extra restrictions are made to changes of the server + partition's TCE table beside those stated in 2 above. The server + partition can only target its own memory or the explicitly granted + partner partition’s memory. + + + + The H_MIGRATE_DMA hcall() made by a partner partition migrates + the page referenced by the RTCE table TCE but follows the RTCE table TCE + copy pointer, if valid, to the server partition’s IOA’s TCE + table to determine which IOA’s DMA to disable, thus allowing + migration of partner partition pages underneath server partition DMA + activity. In this case, however, the H_MIGRATE_DMA algorithm is modified + such that server partition’s IOA’s TCE table is atomically + updated, after the page migration but prior to enabling the IOA’s + DMA, only when its contents still are a valid copy of the partner + partition’s RTCE table TCE contents. The H_MIGRATE_DMA hcall() also + serializes with H_PUT_RTCE so that new copies of the RTCE table TCE are + not made during the migration of the underlying page. + + + + The server partition should never call H_MIGRATE_DMA for any + Redirected RDMA mapped pages, however, to check, the H_MIGRATE_DMA + hcall() is enhanced to check the Logical Memory Block (LMB) owner in the + TCE and reject the call if the LMB did not belong to the + requester. + + + +
+ H_PUT_RTCE + This hcall() maps “count” number of contiguous TCEs in + an RTCE to the same number of contiguous IOA TCEs. The H_REMOVE_RTCE + hcall() is used to back-out TCEs built with H_PUT_RTCE hcall(). + for that hcall(). + + + Syntax: + + + + + + + Parameters: + + + + r-liobn: Handle of RDMA RTCE table + + + + r-ioba: IO address per RDMA RTCE table + + + + liobn: Logical I/O Bus Number of server TCE table + + + + ioba: I/O address as seen by server IOA + + + + count: Number of consecutive 4 KB pages to map + + + + + + Semantics: + + + + Validates r-liobn is from the second triple (second window pane) + of the server partition’s + “ibm,my-dma-window” property, else return + H_Parameter. + + + + Validates r-ioba plus (count * 4 KB) is within range of RTCE + table as specified by the window pane as specified by the r-liobn, else + return H_Parameter. + + + + Validates that the TCE table associated with liobn is owned by + calling partition, else return H_Parameter. + + + + If the Shared Logical Resource option is implemented and the + LIOBN, represents a logical resource that has been rescinded by the + owner, return H_RESCINDED. + + + + + + Validates that ioba plus (count * 4 KB) is within the range of + TCE table specified by liobn, else return H_Parameter. + + + + If the Shared Logical Resource option is implemented and the IOBA + represents a logical resource that has been rescinded by the owner, + return H_RESCINDED. + + + + + + For count entries + + + + The following is done in a critical section with respect to + updates to the r-ioba entry of the RTCE table TCE + + + + Check that the r-ioba entry of the RTCE table contains a valid + mapping (this requires having a completed partner connection), else + return H_R_Parm with the value of the loop count in R4. + + + + Prevent multiple redirected mappings of the same r-ioba: If the + r-ioba entry of the RTCE table TCE contains a valid pointer, and if that + pointer references a TCE that is a clone of the r-ioba entry of the RTCE + table TCE, then return H_Resource with the value of the loop count in + R4. + + + + Copy the DMA address mapping from the r-ioba entry of the r-liobn + RTCE table to the ioba entry of the liobn TCE table and save a pointer to + the ioba entry of the liobn TCE table in the r-ioba entry of the r-liobn + RTCE table, or in a separate structure associated with the r-liobn RTCE + table. + + + + + + End Loop (The critical section lasts for one iteration of the + loop) + + + + + + Return H_Success + + + + Implementation Note: The PA requires the OS to issue a sync + instruction to proceed the signalling of an IOA to start an IO operation + involving DMA to guarantee the global visibility of both DMA and TCE + data. This hcall() does not include a sync instruction to guarantee + global visibility of TCE data and in no way diminishes the requirement + for the OS to issue it. + + Implementation Note: The execution time for this hcall() is + expected to be a linear function of the count parameter. Excessive size + of the count parameter may cause an extended delay. + +
+ +
+ H_PUT_RTCE_INDIRECT + This hcall() maps “count” number of potentially + non-contiguous TCEs in an RTCE to the same number of contiguous IOA TCEs. + The H_REMOVE_RTCE hcall() is used to back-out TCEs built with the + H_PUT_RTCE_INDIRECT hcall(). + for that hcall(). + + + Syntax: + + + + + + + Parameters: + + + + buff-addr: The Logical Address of a page (4 KB, 4 KB boundary) + containing a list of r-ioba to be mapped via using the r-liobn RTCE + table + + + + r-liobn: Handle of RTCE table to be used with r-ioba entries in + indirect buffer (second window pane from server + “ibm,my-dma-window” + + + + liobn: Logical I/O Bus Number of server TCE table + + + + ioba: I/O address as seen by server IOA + + + + count: Number of consecutive IOA bus 4 KB pages to map (number of + entries in buffer) + + + + + + Semantics: + + + + Validates r-liobn is from the second triple (second window pane) + of the server partition’s + “ibm,my-dma-window” property, else return + H_Parameter. + + + + Validates buff-addr points to the beginning of a 4 KB page owned + by the calling partition, else return H_Parameter. + + + + If the Shared Logical Resource option is implemented and the + logical address’s page number represents a page that has been + rescinded by the owner, return H_RESCINDED. + + + + + + Validates that the TCE table associated with liobn is owned by + calling partition, else return H_Parameter. + + + + If the Shared Logical Resource option is implemented and the + LIOBN represents a logical resource that has been rescinded by the owner, + return H_RESCINDED. + + + + + + Validates that ioba plus (count * 4 KB) is within the range of + TCE table specified by liobn, else return H_Parameter. + + + + If the Shared Logical Resource option is implemented and the IOBA + represents a logical resource that has been rescinded by the owner, + return H_RESCINDED. + + + + + + If the count field is greater than 512 return H_Parameter. + + + + Copy (count * 8) bytes from the page specified by buff-addr to a + temporary hypervisor page for contents verification and processing (this + avoids the problem of the caller changing call by reference values after + they are checked). + + + + For count entries: + + + + Validate the r-ioba entry in the temporary page is within range + of RTCE table as specified by r-liobn, else place the count number in R4 + and return H_R_Parm. + + + + n End loop + + + + + + For count validated entries in the hypervisor's temporary + page: + + + + The following is done in a critical section with respect to + updates to the r-ioba entry of the RTCE + + + + Check that the r-ioba entry of the r-liobn RTCE table contains a + valid mapping (this requires having a completed partner connection), else + return H_R_Parm with the count number in R4. + + + + Prevent multiple redirected mappings of the same r-ioba: If the + r-ioba entry of the r-liobn RTCE table contains a valid pointer, and if + that pointer references a TCE entry that is a clone of the r-ioba entry + of the RTCE table, then return H_Resource with the count number in + R4. + + + + Copy the DMA address mapping from the r-ioba entry of the r-liobn + RTCE table to the ioba entry of the liobn TCE table and save a pointer to + the ioba entry of the liobn TCE table in the r-ioba entry of the r-liobn + RTCE table, or into a separate structure associated with the r-liobn RTCE + table. + + + + + + End Loop (The critical section lasts for one iteration of the + loop) + + + + + + Return H_Success + + + + Implementation Note: The PA requires the OS to issue + a sync instruction to proceed the signalling of an IOA to start an IO + operation involving DMA to guarantee the global visibility of both DMA + and TCE data. This hcall() does not include a sync instruction to + guarantee global visibility of TCE data and in no way diminishes the + requirement for the OS to issue it. + + Implementation Note: The execution time for this + hcall is expected to be a linear function of the count parameter. + Excessive size of the count parameter may cause an extended delay. + +
+ +
+ H_REMOVE_RTCE + The H_REMOVE_RTCE hcall() is used to back-out TCEs built with + H_PUT_RTCE and H_PUT_RTCE_INDIRECT hcall()s. That is, to remove the TCEs + from the IOA TCE table and links put into the RTCE table as a result of + the H_PUT_RTCE or H_PUT_RTCE_INDIRECT hcall()s. + + + Syntax: + + + + + + + Parameters: + + + + r-liobn: Handle of RDMA RTCE table + + + + r-ioba: IO address per RDMA RTCE table + + + + liobn: Logical I/O Bus Number of server TCE table + + + + ioba: I/O address as seen by server IOA + + + + count: Number of consecutive 4 KB pages to unmap + + + + tce-value: TCE value to be put into the IOA TCE(s) after setting + the “Page Mapping and Control” bits to “Page fault (no + access)”. + + + + + + Semantics: + + + + Validates r-liobn is from the second triple (second window pane) + of the server partition’s + “ibm,my-dma-window” property, else return + H_Parameter. + + + + Validates r-ioba plus (count * 4 KB) is within range of RTCE + table as specified by the window pane as specified by the r-liobn, else + return H_Parameter. + + + + Validates that the TCE table associated with liobn is owned by + calling partition, else return H_Parameter. + + + + If the Shared Logical Resource option is implemented and the + LIOBN, represents a logical resource that has been rescinded by the + owner, return H_RESCINDED. + + + + + + Validates that ioba plus (count * 4 KB) is within the range of + TCE table specified by liobn, else return H_Parameter. + + + + If the Shared Logical Resource option is implemented and the IOBA + represents a logical resource that has been rescinded by the owner, + return H_RESCINDED. + + + + + + For count entries + + + + The following is done in a critical section with respect to + updates the r-ioba entry of the RTCE table TCE + + + + If it exists, invalidate the pointer in the r-ioba entry of the + r-liobn RTCE table (or in a separate structure associated with the + r-liobn RTCE table). + + + + Replace the ioba entry of the liobn TCE table with tce-value + after setting the “Page Mapping and Control” bits to + “Page fault (no access)”. + + + + + + n End Loop (The critical section lasts for one iteration of the + loop) + + + + + + Return H_Success + + + + Implementation Note: The execution time for this hcall() is + expected to be a linear function of the count parameter. Excessive size + of the count parameter may cause an extended delay. + +
+ +
+ Redirected RDMA TCE Recovery and In-Flight DMA + There are certain error or error recovery scenarios that may + attempt to unmap a TCE in an IOA’s TCE table prior to the + completion of the operation which setup the TCE. For example: + + + + A client attempts to H_PUT_TCE to its DMA window pane, which is + mapped to the second window pane of the server’s DMA window, and + the TCE in the RTCE table which is the target of the H_PUT_TCE already + points to a valid TCE in an IOA’s TCE table. + + + + A client attempts to H_FREE_CRQ and the server’s second + window pane for that virtual IOA contains a TCE which points to a valid + TCE in an IOA’s TCE table. + + + + A client partition attempts to reboot (which essentially is an + H_FREE_CRQ). + + + + A server attempts to H_FREE_CRQ and the server’s second + window pane for that virtual IOA contains a TCE which points to a valid + TCE in an IOA’s TCE table. + + + + In such error and error recovery situations, the hypervisor + attempts to prevent the changing of an IOAs TCE to a value that would + cause a non-recoverable IOA error. One method that the hypervisor may use + to accomplish this is that on a TCE invalidation operation, set the value + of the read and write enable bits in the TCE to allow DMA writes but not + reads, and to change the real page number in the TCE to target a dummy + page. In this case the IOA receives an error (Target Abort) on attempts + to read, while DMA writes (which were for a defunct operation) are + silently dropped. This works well when all the following are true: + + + + The platform supports separate TCE read and write enable bits in + the TCE + + + + EEH is enabled and the DD can recover from the MMIO Stopped and + DMA Stopped states + + + + The IOA and the IOA’s DD can recover gracefully from Target + Aborts (which are received on a read to a page where the read enable bit + is off) + + + + If these conditions are not true then the hypervisor will need to + try to prevent or delay invalidation of the TCEs. The H_Resource return + from the H_FREE_CRQ, H_PUT_TCE, H_PUT_TCE_INDIRECT, and H_STUFF_TCE can + be used to hold-off the invalidation until which time the IOA can + complete the operation and the server can invalidate the IOA’s TCE. + In addition, the Bit Bucket Allowed LIOBN attribute and the + H_LIOBN_ATTRIBUTES hcall can be used to help enhance the recoverability + in these error scenarios (see + and + for more information). +
+ +
+ LIOBN Attributes + There are certain LIOBN attributes that are made visible to and can + be manipulated by partition software. The H_LIOBN_ATTRIBUTES hcall is + used to read and modify the attributes (see + ). + defines the attributes that are + visible and manipulatable. +   + + LIOBN Attributes + + + + + + + + + Bit(s) + + + + + Field Name + + + + + Definition + + + + + + + + 0-62 + + + Reserved + + +   + + + + + 63 + + + Bit Bucket Allowed + + + 1: For an indirect IOA TCE invalidation operation (that + is, via an operation other than an H_PUT_TCE directly to the + TCE by the partition owning the IOA), the platform may set the + value of the read and write enable bits in the TCE to allow DMA + writes but not reads and change the real page number in the TCE + to target a dummy page (the IOA receives an error (Target + Abort) on attempts to read, while DMA writes (which were for a + defunct operation) are silently dropped). + 0: The platform must reasonably attempt to prevent an + indirect (that is, via an operation other than an H_PUT_TCE + directly to the TCE by the partition owning the IOA) + modification an IOA’s valid TCE so that a possible + in-flight DMA does not cause a non-recoverable error. + Software Implementation Notes: + + + + The results of changing this field when there are + valid TCEs for the LIOBN may produce unexpected results. The + hypervisor is not required to prevent such an operation. + Therefore, the H_LIOBN_ATTRIBUTES call to change the value of + this field should be made when there are no valid TCEs in the + table for the IOA. + + + + This field may be implemented but not changeable (the + actual value will be returned in R4 as a result of the + H_LIOBN_ATTRIBUTES hcall() regardless, with a status of + H_Constrained if not changeable). + + + + + + + +
+
+ +
+ H_LIOBN_ATTRIBUTES + + + + R1--1. + + If the H_LIOBN_ATTRIBUTES hcall is + implemented, then it must implement the attributes as they are defined in + + and the syntax and semantics as + defined in + . + + + + + R1--2. + + The H_LIOBN_ATTRIBUTES hcall must + ignore bits in the set-mask and reset-mask which are not implemented and + must process as an exception those which cannot be changed (H_Constrained + returned), and must return the following for the LIOBN Attributes in + R4: + + + + + + + A value of 0 for unimplemented bit positions. + + + + The resultant field values for implemented fields. + + + + + Syntax: + + + + + + + Parameters: + liobn: The LIOBN on which this Attribute modification is to be + performed. + reset-mask: The bit-significant mask of bits to be reset in the + LIOBN’s Attributes (the reset-mask bit definition aligns with the + bit definition of the LIOBN’s Attributes, as defined in + ). The complement of the + reset-mask is ANDed with the LIOBN’s Attributes, prior to applying + the set-mask. See semantics for more details on any field-specific + actions needed during the reset operations. If a particular field + position in the LIOBN Attributes is not implemented, then the + corresponding bit(s) in the reset-mask are ignored. + set-mask: The bit-significant mask of bits to be set in the + LIOBN’s Attributes (the set-mask bit definition aligns with the bit + definition of the LIOBN’s Attributes, as defined in + ). The set-mask is ORed with + the LIOBN’s Attributes, after to applying the reset-mask. See + semantics for more details on any field-specific actions needed during + the set operations. If a particular field position in the LIOBN + Attributes is not implemented, then the corresponding bit(s) in the + set-mask are ignored. + + + + Semantics: + + + + Validate that liobn belongs to the partition, else + H_Parameter. + + + + If the Bit Bucket Allowed field of the specified LIOBN’s + Attributes is implemented and changeable, then set it to the result + of: + Bit Bucket Allowed field contents ANDed with the complement of the + corresponding bits of the reset-mask and then ORed with the corresponding + bits of the set-mask. + + + + Load R4 with the value of the LIOBN’s Attributes, with any + unimplemented bits set to 0, and if all requested changes were made, then + return H_Success, otherwise return H_Constrained. + + + +
+ +
+ Extensions to Other hcall()s for Redirected + RDMA + + +
+ H_PUT_TCE, H_PUT_TCE_INDIRECT, and + H_STUFF_TCE + These hcall()s are only valid for the first window pane of the + “ibm,my-dma-window” property. See + for information about window + pane types. + The following are extensions that apply to the H_PUT_TCE, + H_PUT_TCE_INDIRECT, and H_STUFF_TCE hcall()s in their use against an RTCE + table. + Recognize the validated (owned by the calling partition, else + H-Parameter) LIOBN as referring to a RTCE table (first window pane) and + access accordingly: + + + + If the TCE is not from the first triple (first window pane) of + the calling partition’s + “ibm,my-dma-window” property, return + H_Parameter. + + + + If the TCE is not currently in use: Clear/invalidate the TCE copy + pointer and enter the TCE mapping per the input parameters to the + hcall(). + + + + If the TCE contains a valid mapping and the TCE copy pointer is + invalid: Enter the TCE mapping per the input parameters to the + hcall(). + + + + If the TCE contains a valid mapping and the TCE copy pointer + references a TCE that does not contain a valid copy of the previous + mapping in the TCE: Clear/invalidate the TCE copy pointer and enter the + TCE mapping per the input parameters to the hcall(). + + + + If the TCE contains a valid mapping and the TCE copy pointer + references a TCE that does contain a valid copy of the previous mapping + in the TCE, then: + + + + If the Bit Bucket Allowed Attribute of the LIOBN containing the + TCE is a 1, invalidate the copied TCE and enter the TCE mapping per the + input parameters to the hcall(). + + + + If the Bit Bucket Allowed Attribute of the LIOBN containing the + TCE is a 0, then return H_Resource or perform some other + platform-specific error recovery. + + + + +
+ +
+ H_MIGRATE_DMA + Check that the pages referenced by the TCEs specified in the + mappings to be migrated belong to the calling partition, else + H_Parameter. + If the mapping being migrated is via an RTCE table (that is, LIOBN + points to an RTCE table), then follow the valid redirected TCE pointer + and migrate the redirected page (if the redirected TCE mapping is still a + clone of the original RTCE table entry). + If the mapping being migrated is via an RTCE table and if the RTCE + table TCEs were built with the H_MASS_MAP_TCE hcall(), then expand each + mass mapped area into smaller 4 KB granularities, as necessary to avoid + performance and locking issues, during the migration process. + Insert checking, and potentially delays, to allow IOAs to make + forward progress between successive DMA disables caused by multiple + partner partitions making simultaneous uncoordinated calls to + H_MIGRATE_DMA targeting the same IOA. +
+
+
+ +
+ Subordinate Command/Response Queue (Sub-CRQ) + The Sub-CRQ facility is used in conjunction with the CRQ facility, + for some virtual IOA types, when more than one queue is needed for the + virtual IOA. For information on the CRQ facility, see + . For information on which + virtual IOAs may use the Sub-CRQ facilities, see the applicable sections + for the virtual IOAs. See + for a comparison of the + differences in the queue structures between CRQs and Sub-CRQs. In + addition to the hcall()s specified in + , all of the following hcall()s + and RTAS calls are applicable to both CRQs and Sub-CRQs: + + + + H_XIRR + + + + H_EOI + + + + ibm,int-on + + + + ibm,int-off + + + + ibm,set-xive + + + + ibm,get-xive + + + +   + + CRQ and Sub-CRQ Comparison + + + + + + + + + Characteristic + + + + + CRQ + + + + + Sub-CRQ + + + + + + + + Queue entry size + + + 16 + + + 32 + + + + + Transport and initialization events + + + Applicable + + + Not applicable (coordinated through the CRQ that is + associated with the Sub-CRQ) + + + + + Registration + + + H_REG_CRQ + + + H_REG_SUB_CRQ + + + + + Deregistration + + + H_FREE_CRQ + + + H_FREE_SUB_CRQ + Note: H_FREE_CRQ for the associated CRQ implicitly + deregisters the associated Sub-CRQs + + + + + Enable + + + H_ENABLE_CRQ + + + Not applicable + + + + + Interrupt number + + + Obtained from + “interrupts” property + + + Obtained from H_REG_SUB_CRQ + + + + + Interrupt enable/disable + + + H_VIO_SIGNAL + + + H_VIOCTL subfunction + For virtual IOAs that define the use of Sub-CRQs, the + interrupt associated with the CRQ, as defined by the + “interrupts” property in the + OF device tree, may be enabled or disabled with either the + H_VIOCTL or the H_VIO_SIGNAL hcall(). The CRQ interrupt + associated with a CRQ of a virtual IOA that does not define + the use of Sub-CRQs should be enabled and disabled by use of + the H_VIO_SIGNAL hcall(). + + + + + + hcall() used to place entry on queue + + + H_SEND_CRQ + + + H_SEND_SUB_CRQ + H_SEND_SUB_CRQ_INDIRECT + + + + + Number of queues per virtual IOA + + + One + + + Zero or more, depending on virtual IOA architecture, + implementation, and client/server negotiation + + + + +
+ +
+ Sub-CRQ Format and Registration + Each Sub-CRQ is built of one or more 4 KB pages aligned on a 4 KB + boundary within partition memory, and is organized as a circular buffer + of 32 byte long elements. Each queue is mapped into contiguous I/O + addresses via the TCE mechanism and RTCE table (first window pane). The + I/O address and length of each queue is registered by the process defined + in + . This registration process + tells the hypervisor where to find the virtual IOA’s + Sub-CRQ(s). +
+ +
+ Sub-CRQ Entry Format + Each Sub-CRQ entry consists of a 32 byte element. The first byte of + a Sub-CRQ entry is the Header byte and is defined in + . +   + + Sub-CRQ Entry Header Byte Values + + + + + + + + + Header Value + + + + + Description + + + + + + + + 0 + + + Element is unused -- all other bytes in the element are + undefined. + + + + + 0x01 - 0x7F + + + Reserved. + + + + + 0x80 + + + Valid Command/Response entry. + + + + + 0x81 - 0xFF + + + Reserved. + + + + +
+ The platform (transport mechanism) ignores the contents of all + non-header bytes in all Sub-CRQ entries. + The operational state of any Sub-CRQs follows the operational state + of the CRQ to which the Sub-CRQ is associated. That is, the CRQ transport + is required to be operational in order for any associated Sub-CRQs to be + operational (for example, if an H_SEND_CRQ hcall() would not succeed due + to any reason other than lack of space is available in the CRQ, then an + H_SEND_SUB_CRQ or H_SEND_SUB_CRQ_INDIRECT hcall() to the associated + Sub-CRQ would also fail). Hence, the Sub-CRQ transport does not implement + the transport and initialization events that are implemented by the CRQ + facility. +
+ +
+ Sub-CRQ Entry Processing + During the Sub-CRQ registration (H_REG_SUB_CRQ), the platform + firmware sets all the header bytes of the Sub-CRQ being registered to + zero (entry invalid). After registration, the first valid entry is placed + in the first element and the process proceeds to the end of the queue and + then wraps around to the first entry again (given that the entry has been + subsequently marked as invalid). This allows both the partition software + and transport firmware to maintain independent pointers to the next + element they will be respectively using. + A sender uses an H_SEND_SUB_CRQ hcall() to enter one 32 byte + message on its partner’s Sub-CRQ. Prior to enqueueing an entry on + the Sub-CRQ, the platform first checks if the session to the + partner’s associate CRQ is open, and there is a enough free space + on the Sub-CRQ, if not, it returns an error. If the checks succeed, the + contents of the message is copied into the next free queue element, + potentially notifying the receiver, and returns a successful status to + the caller. The caller may also insert more than one entry on the queue + with one hcall() using H_SEND_SUB_CRQ_INDIRECT. Use of this hcall() + requires that there be enough space on the queue for all the entries, + otherwise none of the entries are placed onto the Sub-CRQ. + At the receiver’s option, it may be notified via an interrupt + when an element is enqueued to its Sub-CRQ. See + . + When the receiver has finished processing a Sub-CRQ entry, it + writes the header to the value 0x00 to invalidate the entry and free it + for future entries. + Should the receiver wish to terminate or reset the communication + channel it deregisters the Sub-CRQ (H_FREE_SUB_CRQ), and if it needs to + re-establish communications, proceeds to register (H_REG_SUB_CRQ) either + the same or different section of memory as the new queue, with the queue + pointers reset to the first entry. Deregistering a CRQ (H_FREE_CRQ) is an + implicit deregistration of any Sub-CRQs associated with the CRQ. +
+ +
+ Sub-CRQ Facility Interrupt Notification + The receiver can set the virtual interrupt associated with its + Sub-CRQ to one of two modes. These are: + + + + Disabled (an enqueued interrupt is not signaled). + + + + Enabled (an enqueued interrupt is signaled on every + enqueue). + + + + Note: An enqueue is considered a pulse not a level. + The pulse then sets the memory element within the emulated interrupt + source controller. This allows the resetting of the interrupt condition + by simply issuing the H_EOI hcall() as is done with the PCI MSI + architecture rather than having to do an explicit interrupt reset as in + the case with PCI Level Sensitive Interrupt (LSI) architecture. + The interrupt mechanism is capable of presenting only one interrupt + signal at a time from any given interrupt source. Therefore, no + additional interrupts from a given source are ever signaled until the + previous interrupt has been processed through to the issuance of an H_EOI + hcall(). Specifically, even if the interrupt mode is enabled, the effect + is to interrupt on an empty to non-empty transition of the queue. + However, as with any asynchronous posting operation race conditions are + to be expected. That is, an enqueue can happen in a window around the + H_EOI hcall(). Therefore, the receiver should poll the Sub-CRQ (that is, + look at the header byte of the next queue entry to see if the entry is + valid) after an H_EOI to prevent losing initiative. + The hcall() used to enable and disable this Sub-CRQ interrupt + notification is H_VIO_SIGNAL (see + ). +
+ +
+ Extensions to Other hcall()s for Sub-CRQ + + +
+ H_MIGRATE_DMA + Since Sub-CRQs are RTCE table mapped, the H_MIGRATE_DMA hcall() may + be requested to move a page that is part of a Sub-CRQ. The OS owner of + the queue is responsible for preventing its processors from modifying the + page during the migrate operation (as is standard practice with this + hcall()), however, the H_MIGRATE_DMA hcall() serializes with the Sub-CRQ + hcall()s to direct new elements to the migrated target page. +
+ +
+ H_XIRR, H_EOI + The Sub-CRQ facility utilizes a virtual interrupt source number to + notify the queue owner of new element enqueues. The standard H_XIRR and + H_EOI hcall()s are extended to support this virtual interrupt mechanism, + emulating the standard PowerPC Interrupt hardware with respect to the + virtual interrupt source number. +
+ +
+ +
+ Sub-CRQ Facility Requirements + + + + R1--1. + + + For the Sub-CRQ facility: The platform must implement + the Sub-CRQ as specified in + . + + + + + R1--2. + + + For the Sub-CRQ facility: + The platform must + start enqueueing Commands/Responses to the newly registered Sub-CRQ + starting at offset zero and proceeding as in a circular buffer, each + entry being 32 byte aligned. + + + + + R1--3. + + + For the Sub-CRQ facility: + The platform must + enqueue Commands/Responses only if the 32 byte entry is free (header byte + contains 0x00), else the enqueue operation fails. + + + + + R1--4. + + + For the Sub-CRQ facility: The first byte of a Sub-CRQ + entry must be the Header byte and must be as defined in + . + + + + + R1--5. + + + For the Sub-CRQ facility option: Platforms that + implement the H_MIGRATE_DMA hcall() must implement that function for + pages mapped for use by the Sub-CRQ. + + + + + R1--6. + + + For the Sub-CRQ facility: The platforms must emulate + the standard PowerPC External Interrupt Architecture for the interrupt + source numbers associated with the virtual devices via the standard RTAS + and hypervisor interrupt calls and must extend H_XIRR and H_EOI hcall()s + as appropriate for Sub-CRQ interrupts. + + + +
+
+
+ +
+ Partition Managed Class - Synchronous + Infrastructure + The architectural intent of the Synchronous VIO infrastructure is + for platforms where the communicating partitions are under the control of + the same hypervisor. Operations between the partitions are via + synchronous hcall() operations. The Synchronous VIO infrastructure + defines three options: + + + + Reliable Command/Response Transport option (see + + + + + Subordinate CRQ Transport option (see + + + + + Logical Remote DMA (LRDMA) option (see + ) + + + +
+ Reliable Command/Response Transport Option + For the synchronous infrastructure, the CRQ facility defined in + is + implemented via the Reliable Command/Response Transport + option. The synchronous nature of this infrastructure allows for the + capability to immediately (synchronously) notify the sender of the + message whether the message was delivered successfully or not. + +
+ Reliable CRQ Format and Registration + The format of the CRQ is as defined in + . + The I/O address and length of the queue are registered using the + H_REG_CRQ hcall(). + . +
+ +
+ Reliable CRQ Entry Format + See + . +
+ +
+ Reliable CRQ Entry Processing + A sender uses the H_SEND_CRQ hcall() to enter a 16 byte message on + its partner’s queue. The hcall() takes the entire message as input + parameters in two registers. + . +
+ +
+ Reliable Command/Response Transport Interrupt + Notification + The receiver can enable and disable the virtual interrupt + associated with its CRQ. See + . +
+ +
+ Reliable Command/Response Transport hcall()s + The H_REG_CRQ and H_FREE_CRQ hcall()s are used by both client and + server virtual IOA device drivers. It is the architectural intent that + the hypervisor maintains a connection control structure for each defined + partner/server connection. The H_REG_CRQ and its corresponding H_FREE_CRQ + register and deregister partition resources with that connection control + structure. However, there are several conditions that can arise + architecturally with this connection process (the design of an + implementation may preclude some of these conditions). + + + + The association connection to the partner virtual IOA not being + defined (H_Not_Found). The CRQ registration function fails if the CRQ is + not registered with the hypervisor. + + + + The partner virtual IOA may not have registered its CRQ + (H_Closed). The CRQ is registered with the hypervisor and the connection. + However, the connection is incomplete because their partner has not + registered. + + + + The partner virtual IOA may be already connected to another + partner virtual IOA (H_Resource). The CRQ registration function fails if + the CRQ is not registered with the hypervisor or the connection. + + + + The reaction of the virtual IOA device driver to these conditions + is somewhat different depending upon the calling device driver being for + a client or server IOA. Server IOAs in many cases register prior to their + partner IOAs since they are servers and subsequently wait for service + requests from their clients. Therefore, the H_Closed return code is to be + expected when the DD’s CRQ has been registered with the connection + and is just waiting for the partner to register. Should a partner DD + register its CRQ in the future, higher level protocol messages (via the + Initialization Command/Response CRQ entry) can notify the server DD when + the connection is established. If a client IOA registers and receives a + return code of H_Closed, it may choose to deregister the CRQ and fail + since the client IOA would not be in a position to successfully send + service requests using the CRQ facility, or it may wait and rely upon + higher level CRQ messages (via the Initialization Command/Response CRQ + entry) to tell it when its partner has registered. The reaction of a + virtual IOA DDs to H_Not_Found and H_Resource are dependent upon the + functionality of higher level platform and system management policies. + While the current registration has failed, higher level system and or + platform management actions may allow a future registration request to + succeed. + When registration succeeds, an association is made between the + partner partition’s LIOBN (RTCE table) and the second window pane + of the server partition. This association is dropped when either partner + deregisters or terminates. However, on deregistration or termination, the + RTCE tables associated with the local partition (first window pane) + remain intact for that partition (see Requirement + ). + +
+ H_REG_CRQ + This hcall() registers the RTCE table mapped memory that contains + the CRQ. + + + Syntax: + + + + + + + Parameters: + + + + unit-address: Unit Address per device tree node + “reg” property + + + + queue: I/O address (offset into the RTCE table) of the CRQ buffer + (starting on a 4 KB boundary). + + + + len: Length of the CRQ in bytes (a multiple of 4 KB) + + + + + + + Semantics: + + + + Validate unit-address, else H_Parameter + + + + Validate queue, which is the I/O address of the CRQ (I/O + addresses for entire buffer length starting at the specified I/O address + are translated by the RTCE table, is 4 KB aligned, and length, len, is a + multiple of 4 KB), else H_Parameter + + + + Validate that there is an authorized connection to another + partition associated with the Unit Address, else H_Not_Found. + + + + Validate that the authorized connection to another partition + associated with the Unit Address is free, else H_Resource. + + + + Initialize the CRQ enqueue pointer and length variables. These + variables are kept in terms of I/O addresses so that page migration works + and any remapping of TCEs is effective. + + + + Disable CRQ interrupts. + + + + Allow for Logical Remote DMA, when applicable, with associated + partner partition when partner registers. + + + + If partner is already registered, then return H_Success, else + return H_Closed. + + + +
+ +
+ H_FREE_CRQ + This hcall() deregisters the RTCE table mapped memory that contains + the CRQ. In addition, if there are any Sub-CRQs associated with the CRQ, + the H_FREE_CRQ has the effect of releasing the Sub-CRQs. + + + Syntax: + + + + + + + Parameters: + + + + unit-address: Unit Address per device tree node + “reg” property + + + + + + Semantics: + + + + Validate unit-address, else H_Parameter + + + + Mark the connection to the associated partner partition as closed + (so that send hcall()s from the partner partition fail). + + + + Mark the CRQ enqueue pointer and length variables as + invalid. + + + + For any and all Sub-CRQs associated with the CRQ, do the + following: + + + + Mark the connection to the associated partner partition as closed + for the Sub-CRQ (so that send hcall()s from the partner partition + fail). + + + + Mark the Sub-CRQ enqueue pointer and length variables for the + Sub-CRQ as invalid. + n Disable Sub-CRQ interrupts for the Sub-CRQ. + + + + + + Disable CRQ interrupts. + + + + If there exists any Redirected TCEs in the local TCE tables + associated with this Virtual IOA, and all of those tables have a Bit + Bucket Allowed attribute of 1, then Disable Logical Remote DMA with + associated partner partition, if enabled, invalidating any Redirected + TCEs in the local TCE tables (for information on invalidation of TCEs, + see ). + + + + If there exists any Redirected TCEs in the local TCE tables + associated with this Virtual IOA, and any of those tables have a Bit + Bucket Allowed attribute of 0, then return H_Resource or perform some + other platform-specific error recovery. + + + + Send partner terminated message to partner queue (if it is still + registered), overlaying the last valid entry in the queue if the CRQ is + full. + + + + Return H_Success. + + + + Implementation Note: If the hypervisor returns an + H_Busy, H_LongBusyOrder1mSec, or H_LongBusyOrder10mSec, software must + call H_FREE_CRQ again with the same parameters. Software may choose to + treat H_LongBusyOrder1mSec and H_LongBusyOrder10mSec the same as H_Busy. + The hypervisor, prior to returning H_Busy, H_LongBusyOrder1mSec, or + H_LongBusyOrder10mSec, will have placed the virtual adapter in a state + that will cause it to not accept any new work nor surface any new virtual + interrupts (no new entries will be placed on the CRQ). + +
+ +
+ H_SEND_CRQ + This hcall() sends one 16 byte entry to the partner + partition’s registered CRQ. + + + Syntax: + + + + + + + Parameters: + + + + unit-addr: Unit Address per device tree node + “reg” property + + + + msg-high: + n header: high order bit is on -- header of value 0xFF is reserved + for transport error and is invalid for input. + n format: not checked by the firmware. + + + + msg-low: not checked by the firmware -- should be consistent with + the definition of the format byte. + + + + + + Semantics: + + + + Validate the Unit Address, else return H_Parameter + + + + Validate that the msg header byte has its high order bit on and + that it is not = 0xFF, else return H_Parameter. + + + + Validate that there is an authorized connection to another + partition associated with the Unit Address and that the associated CRQ is + enabled, else return H_Closed. + + + + Enter Critical Section on target CRQ + + + + Validate that there is room on the receive queue for the message + and allocate that message, else exit critical Section and return + H_Dropped. + + + + Store msg-low into the second 8 bytes of the allocated queue + element. + + + + Store order barrier + + + + Store msg-high into the first 8 bytes of the allocated queue + element (setting the header valid bit.) + + + + + + Exit Critical Section + + + + If receiver queue interrupt mode == enabled, then signal + interrupt + + + + Return H_Success. + + + +
+ +
+ H_ENABLE_CRQ + This hcall() explicitly enables a CRQ that has been disabled due to + a Partner partition suspended transport event. As a side effect of this + hcall(), all pages that are mapped via the logical TCE table associated + with the first pane of + “ibm,my-dma-window” property of the + associated virtual IOA are restored prior to successful completion of the + hcall(). It is the architectural intent that this hcall() is made while + the logical TCE contains mappings for all the pages that will be involved + in the recovery of the outstanding I/O operations at the time of the + partition migration. Further, it is the architectural intent that this + hcall() is made from a processing context that can handle the expected + busy wait return code without blocking the processor. + + + Syntax: + + + + + + + Parameters: + + + + unit-addr: Unit Address per device tree node + “reg” property + + + + + + Semantics: + + + + Validate the Unit Address, else return H_Parameter + + + + Test that all pages mapped through the logical TCE table + associated with the first pane of the + “ibm,my-dma-window” property associated + with the unit-address parameter are present; else return + H_LongBusyOrder10mSec. + + + + Set the status of the CRQ associated with the unit-address + parameter to enabled. + + + + Return H_Success. + + + +
+
+ +
+ Reliable Command/Response Transport Option + Requirements + + + + R1--1. + + + For the Reliable Command/Response Transport + option: The platform must implement the CRQ facility, as + defined in + . + + + + + R1--2. + + + For the Reliable Command/Response Transport + option: The platform must implement the H_REG_CRQ hcall(). + . + + + + + R1--3. + + + For the Reliable Command/Response Transport + option: The platform must implement the H_FREE_CRQ hcall(). + . + + + + + R1--4. + + + For the Reliable Command/Response Transport + option: The platform must implement the H_SEND_CRQ hcall(). + . + + + + + R1--5. + + + For the Reliable Command/Response Transport + option: The platform must implement the H_ENABLE_CRQ hcall(). + . + + + +
+
+ +
+ Logical Remote DMA (LRDMA) Option + The Logical Remote Direct Memory Access (LRDMA) option allows a + server partition to securely target memory pages within a partner + partition for VIO operations. + This architecture defines two modes of RDMA + + + + Copy RDMA is used to have the hypervisor copy data + between a buffer in the server partition’s memory and a buffer in + the partner partition’s memory. See + for more information on Copy + RDMA with respect to LRDMA. + + + + Redirected RDMA allows for a server partition to + securely target its I/O adapter's DMA operations directly at the memory + pages of the partner partition. The platform overhead of Copy RDMA is + generally greater than Redirected RDMA, but this overhead may be offset + if the server partition’s DMA buffer is being used as a data cache + for multiple VIO operations. See + for more information on + Redirected RDMA with respect to LRDMA. + + + + The mapping between the LIOBN in the second pane of a server + virtual IOA’s + “ibm,my-dma-window” property and the + corresponding partner IOA’s RTCE table is made when the CRQ + successfully completes registration. The partner partition is not aware + if the server partition is using Copy RDMA or Redirected RDMA. The server + partition uses the Logical RDMA mode that best suits its needs for a + given VIO operation. See + for more information on RTCE + tables. + +
+ Copy RDMA + The Copy RDMA hcall()s are used to request that the hypervisor move + data between partitions. The specific implementation is optimized to the + platform’s hardware features. There are calls for when both source + and destination buffers are RTCE table mapped (H_COPY_DMA) and when only + the remote buffers are mapped (H_WRITE_RDMA and H_READ_RDMA). + +
+ H_COPY_RDMA + This hcall() copies data from an RTCE table mapped buffer in one + partition to an RTCE table mapped buffer in another partition, with the + length of the transfer being specified by the transfer length parameter + in the hcall(). The + “ibm,max-virtual-dma-size” property, if + it exists (in the + /vdevice (node), specifies the maximum length of the + transfer (minimum value of this property is 128 KB). + + + Syntax: + + + + + + + Parameters: + + + + len: Length of transfer (length not to exceed the value in the + “ibm,max-virtual-dma-size” property, if + it exists) + + + + s-liobn: LIOBN (RTCE table handle) of V-DMA source buffer + + + + s-ioba: IO address of V-DMA source buffer + + + + d-liobn: LIOBN (RTCE table handle) of V-DMA destination + buffer + + + + d-ioba: I/O address of V-DMA destination buffer + + + + + + Semantics: + + + + Serialize access to RTCE tables with H_MIGRATE_DMA. + + + + If the + “ibm,max-virtual-dma-size” property exist + in the + /vdevice node of the device tree, then if the value + of len is greater than the value of this property, return + H_Parameter. + + + + Source and destination LIOBNs are checked for authorization per + the + “ibm,my-dma-window” property, else return + H_S_Parm or H_D_Parm, respectively. + + + + Source and destination ioba’s and length are checked for + valid ranges per the + “ibm,my-dma-window” property, else return + H_S_Parm or H_D_Parm, respectively. + + + + The access bits of the associated TCEs are checked for + authorization, else return H_Permission. + + + + Copy len number of bytes from the buffer starting at the + specified source address to the buffer starting at the specified + destination address, then return H_Success. + + + +
+ +
+ H_WRITE_RDMA + This hcall() copies up to 48 bytes of data from a set of input + parameters to an RTCE table mapped buffer in another partition. + + + Syntax: + + + + + + + Parameters: + + + + len: Length of transfer + + + + d-liobn: LIOBN (RTCE table handle) of V-DMA destination + buffer + + + + d-ioba: I/O address of V-DMA destination buffer + + + + data1: Source data + + + + data2: Source data + + + + data3: Source data + + + + data4: Source data + + + + data5: Source data + + + + data6: Source data + + + + + + Semantics: + + + + Check that the len parameter => 0 and <= 48, else return + H_Parameter + + + + The destination LIOBN is checked for authorization per the remote + triple of the one of the calling partition’s + “ibm,my-dma-window” property, else return + H_D_Parm. + + + + The destination ioba and length are check for valid ranges per + the remote triple of the one of the calling partition’s + “ibm,my-dma-window” property, else return + H_D_Parm. + + + + Serialize access to the destination RTCE table with + H_MIGRATE_DMA. + + + + The access bits of the associated RTCE table TCEs are checked for + authorization, else return H_Permission. + + + + Copy len number of bytes from the data parameters starting at the + high order byte of data1 toward the low order byte of data 6 into the + buffer starting at the specified destination address, then return + H_Success. + + + +
+ +
+ H_READ_RDMA + This hcall() copies up to 72 bytes of data from an RTCE table + mapped buffer into a set of return registers. + + + Syntax: + + + + + + + Parameters: + + + + len: Length of transfer + + + + s-liobn: LIOBN (RTCE table handle) of V-DMA source buffer + + + + s-ioba: IO address of V-DMA source buffer + + + + + + Semantics: + + + + Check that the len parameter => 0 and <= 72, else return + H_Parameter + + + + The source LIOBN is checked for authorization per the remote + triple of the one of the calling partition’s + “ibm,my-dma-window” property, else return + H_S_Parm. + + + + The source ioba and length are check for valid ranges per the + remote triple of the one of the calling partition’s + “ibm,my-dma-window” property, else return + H_S_Parm. + + + + Serialize access to the source RTCE table with + H_MIGRATE_DMA. + + + + The access bits of the associated RTCE table TCEs are checked for + authorization, else return H_Permission. + + + + Copy len number of bytes from the source data buffer specified by + s-liobn starting at s-ioba, into the registers R4 through R12 starting + with the high order byte of R4 toward the low order byte of R12, then + return H_Success. + + + +
+
+ +
+ Logical Remote DMA Option Requirements + + + + R1--1. + + + For the Logical Remote DMA option: The platform must + implement the H_PUT_RTCE hcall() as specified in + . + + + + + R1--2. + + + For the Logical Remote DMA option: The platform must + implement the extensions to the H_PUT_TCE hcall() as specified in + . + + + + + R1--3. + + + For the Logical Remote DMA option: The platform must + implement the extensions to the H_MIGRATE_DMA hcall() as specified in + . + + + + + R1--4. + + + For the Logical Remote DMA option: The platform must + implement the H_COPY_RDMA hcall() as specified in + . + + + + + R1--5. + + + For the Logical Remote DMA option: + The platform must + disable Logical Remote DMA operations that target an inactive partition + (one that has terminated), including the H_COPY_RDMA hcall() and the + H_PUT_RTCE hcall(). + + + + + + Implementation Note: It is expected that as part of + meeting Requirement + , all of the terminating + partition’s TCE table entries (regular and RTCE) are invalidated + along with any clones (for information on invalidation of TCEs, see + ). While other mechanisms are + available for meeting this requirement in the case of H_COPY_RDMA, this + is the only method for Redirected RDMA, and since it works in both cases, + it is expected that implementations will use this single + mechanism. +
+
+ +
+ Subordinate CRQ Transport Option + For the synchronous infrastructure, in addition to the CRQ facility + defined in + , + the Subordinate CRQ Transport option may also be implemented + in conjunction with the CRQ facility. That is, the Subordinate CRQ + Transport option requires that the Reliable Command/Response Transport + option also be implemented. For this option, the Sub-CRQ facility defined + in + is + implemented. + +
+ Sub-CRQ Format and Registration + The format of the Sub-CRQ is as defined in + . + The I/O address and length of the queue are registered using the + H_REG_SUB_CRQ hcall(). + . +
+ +
+ Sub-CRQ Entry Format + See + . +
+ +
+ Sub-CRQ Entry Processing + A sender uses the H_SEND_SUB_CRQ or H_SEND_SUB_CRQ_INDIRECT hcall() + to enter one or more 32 byte messages on its partner’s queue. + and + . +
+ +
+ Sub-CRQ Transport Interrupt Notification + The receiver can enable and disable the virtual interrupt + associated with its Sub-CRQ using the H_VIOCTL hcall(), with the + appropriate subfunction. See + . The interrupt number that is + used in the H_VIOCTL call is obtained from the H_REG_SUB_CRQ call that is + made to register the Sub-CRQ. +
+ +
+ Sub-CRQ Transport hcall()s + The H_REG_SUB_CRQ and H_FREE_SUB_CRQ hcall()s are used by both + client and server virtual IOA device drivers. It is the architectural + intent that the hypervisor maintains a connection control structure for + each defined partner/server connection. The H_REG_SUB_CRQ and its + corresponding H_FREE_SUB_CRQ register and deregister partition resources + with that connection control structure. However, there are several + conditions that can arise architecturally with this connection process + (the design of an implementation may preclude some of these + conditions). + + + + The association connection to the partner virtual IOA not being + defined (H_Not_Found). + + + + The partner virtual IOA CRQ connection may not have been + completed (H_Closed). + + + + The partner may deregister its CRQ which also deregisters any + associated Sub-CRQs. + + + +
+ H_REG_SUB_CRQ + This hcall() registers the RTCE table mapped memory that contains + the Sub-CRQ. Multiple Sub-CRQ registrations may be attempted for each + virtual IOA. If resources are not available to establish a Sub-CRQ, the + H_REG_SUB_CRQ call will fail with H_Resource. + + Programming Note: On platforms that implement the + partition migration option, after partition migration the support for + this hcall() might change, and the caller should be prepared to receive + an H_Function return code indicating the platform does not implement this + hcall(). If a virtual IOA exists in the device tree after migration that + requires by this architecture the presence of this hcall(), then if that + virtual IOA exists after the migration, it can be expected that the + hcall() will, also. + + + Syntax: + + + + + + + Parameters: + + + + unit-address: Unit Address per device tree node + “reg” property. + + + + Sub-CRQ-ioba: I/O address (offset into the RTCE table, as + specified by the first window pane of the virtual IOA’s + “ibm,my-dma-window” property) of the + Sub-CRQ buffer (starting on a 4 KB boundary). + + + + Sub-CRQ-length: Length of the Sub-CRQ in bytes (a multiple of 4 + KB). + + + + + + Semantics: + + + + Validate unit-address, else H_Parameter. + + + + Validate Sub-CRQ-ioba, which is the I/O address of the Sub-CRQ + (I/O addresses for entire buffer length starting at the specified I/O + address are translated by the RTCE table, is 4 KB aligned, and length, + Sub-CRQ-length, is a multiple of 4 KB), else H_Parameter. + + + + Validate that there are sufficient resources associated with the + Unit Address to allocate the Sub-CRQ, else H_Resource. + + + + Initialize the Sub-CRQ enqueue pointer and length variables. + These variables are kept in terms of I/O addresses so that page migration + works and any remapping of TCEs is effective. + + + + Initialize all Sub-CRQ entry header bytes to 0 (invalid). + + + + Disable Sub-CRQ interrupts. + + + + Place cookie representing Sub-CRQ number (will be used in + H_SEND_SUB_CRQ, H_SEND_SUB_CRQ_INDIRECT, and H_FREE_SUB_CRQ) in + R4. + + + + Place interrupt number (the same as will be returned by H_XIRR or + H_IPOLL for the interrupt from this Sub-CRQ) in R5. + + + + If the CRQ connection is already complete, then return H_Success, + else return H_Closed. + + + +
+ +
+ H_FREE_SUB_CRQ + This hcall() deregisters the RTCE table mapped memory that contains + the Sub-CRQ. Note that the H_FREE_CRQ hcall() also deregisters any + Sub-CRQs associated with the CRQ being deregistered by that + hcall(). + + Programming Note: On platforms that implement the + partition migration option, after partition migration the support for + this hcall() might change, and the caller should be prepared to receive + an H_Function return code indicating the platform does not implement this + hcall(). If a virtual IOA exists in the device tree after migration that + requires by this architecture the presence of this hcall(), then if that + virtual IOA exists after the migration, it can be expected that the + hcall() will, also. + + + Syntax: + + + + + + + Parameters: + + + + unit-address: Unit Address per device tree node + “reg” property. + + + + Sub-CRQ-num: The queue # cookie returned from H_REG_SUB_CRQ + hcall() at queue registration time. + + + + + + Semantics: + + + + Validate unit-address and Sub-CRQ-num, else H_Parameter + + + + Mark the connection to the associated partner partition as closed + for the specified Sub-CRQ (so that send hcall()s from the partner + partition fail). + + + + Mark the Sub-CRQ enqueue pointer and length variables for the + specified Sub-CRQ as invalid. + + + + Disable Sub-CRQ interrupts for the specified Sub-CRQ. + + + + Return H_Success. + + + +
+ +
+ H_SEND_SUB_CRQ + This hcall() sends one 32 byte entry to the partner + partition’s registered Sub-CRQ. + + Programming Note: On platforms that implement the + partition migration option, after partition migration the support for + this hcall() might change, and the caller should be prepared to receive + an H_Function return code indicating the platform does not implement this + hcall(). If a virtual IOA exists in the device tree after migration that + requires by this architecture the presence of this hcall(), then if that + virtual IOA exists after the migration, it can be expected that the + hcall() will, also. + + + Syntax: + + + + + + + Parameters: + + + + unit-addr: Unit Address per device tree node + “reg” property. + + + + Sub-CRQ-num: The queue # cookie returned from H_REG_SUB_CRQ + hcall() at queue registration time. + + + + msg-dword0: firmware checks only high order byte. + + + + msg-dword1, msg-dword2, msg-dword3: the rest of the message; + firmware does not validate. + + + + + + Semantics: + + + + Validate the Unit Address, else return H_Parameter. + + + + Validate that the Sub-CRQ, as specified by Sub-CRQ-num, is + properly registered by the partner, else return H_Parameter. + + + + Validate that the message header byte (high order byte of + msg-dword0) is 0x80, else return H_Parameter. + + + + Validate that there is an authorized CRQ connection to another + partition associated with the Unit Address and that the associated CRQ is + enabled, else return H_Closed. + + + + Enter Critical Section on target Sub-CRQ. + + + + n Validate that there is room on the specified Sub-CRQ for the + message and allocate that message, else exit critical Section and return + H_Dropped. + + + + Store msgdword1 into bytes 4-7 of the allocated queue + element. + + + + Store msgdword2 into bytes 8-11 of the allocated queue + element. + + + + Store msgdword3 into bytes 12-15 of the allocated queue + element. + + + + Store order barrier. + + + + Store msgdword0 into bytes 0-3 of the allocated queue element + (this sets the valid bit in the header byte). + + + + + + Exit Critical Section. + + + + If receiver queue interrupt mode is enabled, then signal + interrupt. + + + + Return H_Success. + + + +
+ +
+ H_SEND_SUB_CRQ_INDIRECT + This hcall() sends one or more 32 byte entries to the partner + partition’s registered Sub-CRQ. On H_Success, all of the entries + have been put onto the Sub-CRQ. On any return code other than H_Success, + none of the entries have been put onto the Sub-CRQ. + + Programming Note: On platforms that implement the + partition migration option, after partition migration the support for + this hcall() might change, and the caller should be prepared to receive + an H_Function return code indicating the platform does not implement this + hcall(). If a virtual IOA exists in the device tree after migration that + requires by this architecture the presence of this hcall(), then if that + virtual IOA exists after the migration, it can be expected that the + hcall() will, also. + + + Syntax: + + + + + + + Parameters: + + + + unit-addr: Unit Address per device tree node + “reg” property. + + + + Sub-CRQ-num: The Sub-CRQ # cookie returned from H_REG_SUB_CRQ + hcall() at queue registration time. + + + + ioba: The address of the TCE-mapped page which contains the + entries to be placed onto the specified Sub-CRQ. + + + + num-entries: Number of entries to be placed onto the specified + Sub-CRQ from the TCE mapped page starting at ioba (maximum number of + entries is 16 in order to minimize the hcall() time). + + + + + + Semantics: + + + + Validate the Unit Address, else return H_Parameter. + + + + Validate that the Sub-CRQ, as specified by Sub-CRQ-num, is + properly registered by the partner, else return H_Parameter. + + + + If ioba is outside of the range of the calling partition assigned + values, then return H_Parameter. + + + + If num-entries is not in the range of 1 to 16, then return + H_Parameter. + + + + Validate that there is an authorized CRQ connection to another + partition associated with the Unit Address and that the associated CRQ is + enabled, else return H_Closed. + + + + Copy (num-entries * 32) bytes from the page specified starting at + ioba to a temporary hypervisor page for contents verification and + processing (this avoids the problem of the caller changing call by + reference values after they are checked). + + + + Validate that the message header bytes for num-entries starting + at ioba are 0x80, else return H_Parameter. + + + + Enter Critical Section on target Sub-CRQ. + + + + Validate that there is room on the specified Sub-CRQ for + num-entries messages and allocate those messages, else exit critical + Section and return H_Dropped. + + + + For each of the num-entries starting at ioba + + + + Store entry bytes 1-31 into bytes 1-31 of the allocated queue + element. + + + + Store order barrier. + + + + Store entry byte 0 into bytes 0 of the allocated queue element + (this sets the valid bit in the header byte). + + + + + + Loop + + + + + + Exit Critical Section. + + + + If receiver queue interrupt mode is enabled, then signal + interrupt. + + + + Return H_Success. + + + +
+
+ +
+ Subordinate CRQ Transport Option Requirements + + + + R1--1. + + For the Subordinate CRQ Transport option: The + platform must implement the Reliable Command/Response Transport option, + as defined in + . + + + + + R1--2. + + For the Subordinate CRQ Transport option: The + platform must implement the Sub-CRQ facility, as defined in + . + + + + + R1--3. + + For the Subordinate CRQ Transport option: The + platform must implement the H_REG_SUB_CRQ hcall(). + . + + + + + R1--4. + + For the Subordinate CRQ Transport option: The + platform must implement the H_FREE_SUB_CRQ hcall(). + . + + + + + R1--5. + + For the Subordinate CRQ Transport option: The + platform must implement the H_SEND_SUB_CRQ hcall(). + . + + + + + R1--6. + + For the Subordinate CRQ Transport option: The + platform must implement the H_SEND_SUB_CRQ_INDIRECT hcall(). + . + + + + + R1--7. + + For the Subordinate CRQ Transport option: The + platform must implement all of the following subfunctions of the H_VIOCTL + hcall() ( + ): + n DISABLE_ALL_VIO_INTERRUPTS + n DISABLE_VIO_INTERRUPT + n ENABLE_VIO_INTERRUPT + + + + +
+ +
+
+
+ +
+ Interpartition Logical LAN (ILLAN) Option + The Interpartition Logical LAN (ILLAN) option provides the + functionality of IEEE VLAN between LPAR partitions. Partitions are + configured to participate in the ILLAN. The participating partitions have + one or more logical IOAs in their device tree. + The hypervisor emulates the functionality of an IEEE VLAN switch. + That functionality is defined in IEEE 802.1Q. The following information on + IEEE VLAN switch functionality is provided for informative reference only + with the referenced document being normative. Logical Partitions may have + one or more Logical LAN IOA’s each of which appears to be connected + to one and only one Logical LAN Switch port of the single Logical LAN + Switch implemented by the hypervisor. Each Logical LAN Switch port is + configured (by platform dependent means) as to whether the attached Logical + LAN IOA supports IEEE VLAN headers or not, and the allowable VLAN numbers + that the port may use (a single number if VLAN headers are not supported, + an implementation dependent number if VLAN headers are supported). When a + message arrives at a Logical LAN Switch port from a Logical LAN IOA, the + hypervisor caches the message’s source MAC address (2nd 6 bytes) to + use as a filter for future messages to the IOA. Then the hypervisor + processes the message differently depending upon whether the port is + configured for IEEE VLAN headers, or not. If the port is configured for + VLAN headers, the VLAN header (bytes offsets 12 and 13 in the message) is + checked against the port’s allowable VLAN list. If the message + specified VLAN is not in the port’s configuration, the message is + dropped. Once the message passes the VLAN header check, it passes onto + destination MAC address processing below. If the port is NOT configured for + VLAN headers, the hypervisor (conceptually) inserts a two byte VLAN header + (based upon the port’s configured VLAN number) after byte offset 11 + in the message. + Next, the destination MAC address (first 6 bytes of the message) is + processed by searching the table of cached MAC addresses (built from + messages received at Logical LAN Switch ports see above). If a match for + the MAC address is not found and if there is no Trunk Adapter defined for + the specified VLAN number, then the message is dropped, otherwise if a + match for the MAC address is not found and if there is a Trunk Adapter + defined for the specified VLAN number, then the message is passed on to the + Trunk Adapter. If a MAC address match is found, then the associated switch + port is configured and the allowable VLAN number table is scanned for a + match to the VLAN number contained in the message’s VLAN header. If a + match is not found, the message is dropped. Next, the VLAN header + configuration of the destination Switch Port is checked, and if the port is + configured for VLAN headers, the message is delivered to the destination + Logical LAN IOA including any inserted VLAN header. If the port is + configured for no VLAN headers, the VLAN header is removed before being + delivered to the destination Logical LAN IOA. + The Logical LAN IOA’s device tree entry includes + Unit Address, and + “ibm,my-dma-window” properties. The + “ibm,my-dma-window” property contains a + LIOBN field that represents the RTCE table used by the Logical IOA. The + Logical LAN hcall()s use the Unit Address field to imply the LIOBN and, + therefore, the RTCE table to reference. + When the logical IOA is opened, the device driver registers, with the + hypervisor, as the “Buffer List”, a TCE mapped page of + partition I/O mapped memory that contains the receive buffer descriptors. + These receive buffers are mapped via a TCE mechanism from partition memory + into contiguous I/O DMA space. The first descriptor in the buffer list page + is that of the receive queue buffer. The rest of the descriptors are for a + number of buffer pools organized by increasing size of receive buffer. The + format of the descriptor is a 1 byte control field, 3 byte buffer length, + followed by a 4 byte I/O address. The number of buffer pools is determined + by the device driver (up to an architected maximum of 254). The control + field in all unused descriptors is 0h00. The last 8 bytes are reserved for + statistics. + When a new message is received by the logical IOA, the list of buffer + pools is scanned starting from the second descriptor in the buffer list + looking for the first available buffer that is equal to or greater than the + received message. That buffer is removed from the pool, filled with the + incoming message, and an entry is placed on the receive queue noting the + buffer status, message length, starting data offset, and the buffer + correlator. + The sender of a logical LAN message uses an hcall() that takes as + parameters the Unit Address and a list of up to 6 buffer descriptors + (length, starting I/O address pairs). The sending hcall(), after verifying + the sender owns the Unit Address, correlates the Unit Address with its + associated Logical LAN Switch port and copies the message from the send + buffer(s) into a receive buffer, as described above, for each target + logical LAN IOA that is a member of the specified VLAN. If a given logical + IOA does not have a suitable receive buffer, the message is dropped for + that logical IOA (a return code indicates that one or more destinations did + not receive a message allowing for a reliable datagram service). + The logical LAN facility uses the standard H_GET_TCE and H_PUT_TCE + hcall()s to manage the I/O translations tables along with H_MIGRATE_DMA to + aid in dynamic memory reconfiguration. + +
+ Logical LAN IOA Data Structures + The Logical LAN IOA defines certain data structures as described in + following paragraphs. + outlines the + inter-relationships between several of these structures. Since multiple + hcall()s as well as multiple partitions access the same structures, + careful serialization is essential. + + Implementation Note: During shutdown or migration of + TCE mapped pages, implementations may choose to atomically maintain, + within a single, two field variable, a usage count of processors + currently sending data through the Logical LAN IOA combined with a + quiesce request set to the processor that is requesting the quiesce (if + no quiesce is requested, the value of this field is some reserved value). + Then a protocol, such as the following, can manage the quiesce of Logical + LAN DMA. A new sender atomically checks the DMA channel management + variable -- spinning if the quiesce field is set and subsequently + incrementing the usage count field when the quiesce variable is not set. + The sender atomically decreases the use count when through with Logical + Remote DMA copying. A quiesce requester, after atomically setting the + quiesce field with its processor number (as in a lock), waits for the + usage count to go to zero before proceeding. + +
+ Logical LAN IOA Structures + + + + + + + + +
+ +
+ Buffer Descriptor + The buffer descriptor is an 8 byte quantity, on an 8 + byte boundary (so that it can be written atomically). The high order byte + is control, the next 3 bytes consist of a length field of the buffer in + bytes, the low order 4 bytes are a TCE mapped I/O address of the start of + the buffer in I/O address space. + Bit 0 of the control field is the valid indicator, 0 means not + valid and 1 is valid. Bits 2-5 are reserved. + Bit 1 is used in the receive queue descriptor as the valid toggle + if the descriptor specifies the receive queue, else it is reserved. If + the valid toggle is a 0, then the newly enqueued receive buffer + descriptors have a valid bit value of 1, if the valid toggle is a 1, then + the newly enqueued receive buffer descriptors have a valid bit value of + 0. The hypervisor flips the value of the valid toggle bit each time it + cycles from the bottom of the receive queue to the top. + Bit 6 is the No Checksum bit and indicates that there is no + checksum in this packet. See + for more information on the + usage of this bit. + Bit 7 is the Checksum Good bit and indicates that the checksum in + this packet has already been verified. See + for more information on the + usage of this bit. +
+ +
+ Buffer List + This structure is used to record buffer descriptors of various + types used by the Logical LAN IOA. Additionally, running statistics about + the logical LAN adapter are maintained at the end of the structure. It + consists of one 4 KB aligned TCE mapped page. By TCE mapping the page, + the H_MIGRATE_DMA hcall() is capable of migrating this structure. + The first buffer descriptor (at offset 0) contains the buffer + descriptor for the receive queue. + The second buffer descriptor (at offset 8) contains the buffer + descriptor for the MAC multicast filter table. + It is the architectural intent that all subsequent buffer + descriptors in the list head a pool of buffers of a given size. Further, + it is the architectural intent that descriptors are ordered in increasing + size of the buffers in their respective pools. The rest of the + description of the ILLAN option is written assuming this intent. However, + the contents of these descriptors are architecturally opaque, none of + these descriptors are manipulated by code above the architected + interfaces. This allows implementations to select the most appropriate + serialization techniques for buffer enqueue/dequeue, migration, and + buffer pool addition and subsequent garbage collection. + The final 8 bytes in the buffer list is a counter of frames dropped + because there was not a buffer in the buffer list capable of holding the + frame. +
+ +
+ Receive Queue + The receive queue is a circular buffer used to store received + message descriptors. The device driver sizes the buffer used for the + receive queue in multiples of 16 bytes, starting on an 16 byte boundary + (to allow atomic store operations) with, at least, one more 16 byte entry + than the maximum number of possible outstanding receive buffers. Failure + to have enough receive queue entries, may result in receive messages, and + their buffers being lost since the logical IOA assumes that there are + always empty receive queue elements and does not check. When the device + driver registers the receive queue buffer, the buffer contents should be + all zeros, this insures that the valid bits are all off. + If a message is received successfully, the next 16 byte area + (starting with the area at offset 0 for the first message received after + the registration of the receive queue and looping back to the top after + the last area is used) in the receive queue is written with a message + descriptor as shown in + . Either the entire entry is + atomically written, or the write order is serialized such that the + control field is globally visible after all other fields are + visible. +   + + Receive Queue Entry + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + Control + + + 0 + + + 1 + + + Bit 0 = the appropriate valid indicator. + Bit 1 = 1 if the buffer contains a valid message. Bit 1 = + 0 if the buffer does not contain a valid message, in which case + the device driver recycles the buffer. + Bits 2-5 Reserved. + Bit 6: No Checksum bit. If a 1, then this indicates that + there is no checksum in this packet (see + for more information + on the usage of this bit). + Bit 7: Checksum Good bit. If a 1, then this indicates + that the checksum in this packet has already been verified (see + + for more information + on the usage of this bit). + + + + + Reserved + + + 1 + + + 1 + + + Reserved for future use. + + + + + Message Offset + + + 2 + + + 2 + + + The byte offset to the start of the received message. The + minimum offset is 8 (to bypass the message correlator field); + larger offsets may be used to allow for optimized data copy + operations. + + + + + Message Length + + + 4 + + + 4 + + + The byte length of the received message. + + + + + Opaque handle + + + 8 + + + 8 + + + Copy of the first 8 bytes contained in the message buffer + as passed by the device driver. + + + + +
+ So that the device driver never has to write into the receive + queue, the VLAN logical IOA alternates the value of the valid bit on each + pass through the receive queue buffer. On the first pass following + registration, the valid bit value is written as a 1, on the next as a + zero, on the third as a 1, and so on. To allow the device driver to + follow the state of the valid bit, the Logical LAN IOA maintains a valid + bit toggle in bit 1 of the receive queue descriptor control byte. The + Logical LAN IOA increments its enqueue pointer after each enqueue. If the + pointer increment (modulo the buffer size) loops to the top, the valid + toggle bit alternates state. + Following the write of the message descriptor, if enqueue + interrupts are enabled and there is not an outstanding interrupt signaled + from the Logical LAN IOA’s interrupt source number, an interrupt is + signaled. + It is the architectural intent that the first 8 bytes of the buffer + is a device driver supplied opaque handle that is copied into the receive + queue entry. One possible format of the opaque handle is the OS effective + address of the buffer control block that pre-ends the buffer as seen by + the VLAN Logical IOA. Within this control block might be stored the total + length of the buffer, the 8 byte buffer descriptor (used to enqueue this + buffer using the H_ADD_LOGICAL_LAN_BUFFER hcall()) and other control + fields as deemed necessary by the device driver. + When servicing the receive interrupt, it is the architectural + intent that the device driver starts to search the receive queue using a + device driver maintained receive queue service pointer (initially + starting, after buffer registration, at the offset zero of the receive + queue) servicing all receive queue entries with the appropriate valid + bit, until reaching the first invalid receive queue entry. The receive + queue service pointer is also post incremented, modulo the receive queue + buffer length, and the device driver’s notion of valid bit state is + also toggled/read from the receive queue descriptor’s valid bit + toggle bit, on each cycle through the circular buffer. After all valid + receive queue entries are serviced, the device driver resets the + interrupt. + . After the interrupt reset, + the device driver again scans from the new value of the receive queue + service pointer to pick up any entries that may have been enqueued during + the interrupt reset window. +
+ +
+ MAC Multicast Filter List + This one 4 KB page (aligned on a 4 KB boundary) opaque data + structure is used by firmware to contain multicast filter MAC addresses. + The table is initialized by firmware by the H_REGISTER_LOGICAL_LAN + hcall(). Any modification of this table by the partition software (OS or + device driver) is likely to corrupt its contents which may corrupt/affect + the OS’s partition but not other partitions, that is, the + hypervisor may not experience significant performance degradation due to + table corruption. However, for the partition that corrupted its filter + list, the hypervisor may deliver multicast address packets that had + previously been requested to be filtered out, or it may fail to deliver + multicast address packets that had been requested to be delivered. +
+ +
+ Receive Buffers + The Logical LAN firmware requires that the minimum size receive + buffer is 16 bytes aligned on an 4 byte boundary so that stores of + linkage pointer may be atomic. Minimum IP message sizes, and message + padding areas force a larger minimum size buffer. + The first 8 bytes of the receive buffer are reserved for a device + driver defined opaque handle that is written into the receive queue entry + when the buffer is filled with a received message. Firmware never + modifies the first 8 bytes of the receive buffer. + From the time of buffer registration via the + H_ADD_LOGICAL_LAN_BUFFER hcall() until the buffer is posted onto the + receive queue, the entire buffer other than the first 8 bytes are subject + to modification by the firmware. Any modification of the buffer contents, + during this time, by non-firmware code subjects receive data within the + partition to corruption. However, any data corruption caused by errors in + partition code does not escape the offending partition, except to the + extent that the corruption involves the data in Logical LAN send + buffers. + Provisions are incorporated in the receive buffer format for a + beginning pad field to allow firmware to make use of data transfer + hardware that may be alignment sensitive. While the contents of the Pad + fields are undefined, firmware is not allowed to make visible to the + receiver more data than was specifically included by the sender in the + transfer message, so as to avoid a covert channel between the + communicating partitions. +   + + Receive Buffer Format + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + + Opaque Handle + + + + 0 + + + 8 + + + Per design of the device driver. + + + + + + Pad 1 + + + + 8 + + + 0-L1 cache line size + + + This field, containing undefined data, may be included by + the firmware to align data for optimized transfers. + + + + + + Message + + + + defined by the “Message Offset” field of the + Receive Queue Entry + + + 12-N + + + The destination and source MAC address are at the first + two 6 byte fields of the message, followed by the message + payload. + + + + + + Pad 2 + + + +   + + + To end of buffer + + + Buffer contents after the Message field are + undefined. + + + + +
+
+
+ +
+ Logical LAN Device Tree Node + The Logical LAN device tree node is a child of the + vdevice node which itself is a child of + / (the root node). There exists one such node for + each logical LAN virtual IOA instance. Additionally, Logical LAN device + tree nodes have associated packages such as obp-tftp and load method as + appropriate to the specific virtual IOA configuration as would the node + for a physical IOA of type network. + Logical IOA’s intrinsic MAC address -- This number is + guaranteed to be unique within the scope of the Logical LAN. +   + + Properties of the Logical LAN OF Device Tree + Node + + + + + + + + + Property Name + + + + + Required? + + + + + Definition + + + + + + + + + “name” + + + + Y + + + Standard property name per + , specifying the + virtual device name, the value shall be + “l-lan”. + + + + + + “device_type” + + + + Y + + + Standard property name per + , specifying the + virtual device type, the value shall be + “network”. + + + + + + “model” + + + + NA + + + Property not present. + + + + + + “compatible” + + + + Y + + + Standard property name per + , specifying the + programming models that are compatible with this virtual IOA, + the value shall include + “IBM,l-lan”. + + + + + + “used-by-rtas” + + + + See definition column + + + Present if appropriate. + + + + + + “ibm,loc-code” + + + + Y + + + Property name specifying the unique and persistent + location code associated with this virtual IOA, the value shall + be of the form defined in + . + + + + + + “reg” + + + + Y + + + Standard property name per + , specifying the unit + address (unit ID) associated with this virtual IOA presented as + an encoded array as with + encode-phys of length + “#address-cells” value shall be + 0xwhatever (virtual + “reg” property used for unit + address no actual locations used, therefore, the size field has + zero cells (does not exist) as determined by the value of the + “#size-cells” property). + + + + + + “ibm,my-dma-window” + + + + Y + + + Property name specifying the DMA window associated with + this virtual IOA presented as an encoded array of three values + (LIOBN, phys, size) encoded as with + encode-int, + encode-phys, and + encode-int. + + + + + + “local-mac-address” + + + + Y + + + Standard property name per + , specifying the + locally administered MAC addresses are denoted by having the + low order two bits of the high order byte being 0b10. + + + + + + “mac-address” + + + + See definition column + + + Initial MAC address (may be changed by + H_CHANGE_LOGICAL_LAN_MAC hcall()). Note: There have been + requests for a globally unique mac address per logical LAN IOA. + However, the combination of -- that requiring that the platform + ship with an unbounded set of reserved globally unique + addresses -- which clearly cannot work -- plus the availability + of IP routing for external connectivity have overridden those + requests. + + + + + + “ibm,mac-address-filters” + + + + Y + + + Property name specifying the number of non-broadcast + multicast MAC filters supported by this implementation (between + 0 and 255) presented as an encoded array encoded as with + encode-int. + + + + + + “interrupts” + + + + Y + + + Standard property name specifying the interrupt source + number and sense code associated with this virtual IOA + presented as an encoded array of two cells encoded as with + encode-int with the first cell containing + the interrupt source number, and the second cell containing the + sense code 0 indicating positive edge triggered. The interrupt + source number being the value returned by the H_XIRR or H_IPOLL + hcall(). + + + + + + “ibm,my-drc-index” + + + + For DR + + +   + + + + + + “ibm,vserver” + + + + Y + + + Property name specifying that this is a virtual server + node. + + + + + + “ibm,trunk-adapter” + + + + See definition column + + + Property name specifying that this is a Trunk Adapter. + This property must be provided when the node is a Trunk Adapter + node. + + + + + + “ibm,illan-options” + + + + See definition column + + + This property is required when any of the ILLAN + sub-options are implemented (see + ). The existence of + this property indicates that the H_ILLAN_ATTRIBUTES hcall() is + implemented, and that hcall() is then used to determine which + ILLAN options are implemented. + + + + + + “supported-network-types” + + + + Y + + + Standard property name as per + . + Reports possible types of “network” + the device can support. + + + + + + “chosen-network-type” + + + + Y + + + Standard property name as per + . + Reports the type of “network” this + device is supporting. + + + + + + “max-frame-size” + + + + Y + + + Standard property name per + , to indicate maximum + packet size. + + + + + + “address-bits” + + + + Y + + + Standard property name per + , to indicate network + address length. + + + + + + “ibm,#dma-size-cells” + + + + See definition column + + + Property name, to define the package’s dma address + size format. The property value specifies the number of cells + that are used to encode the size field of dma-window + properties. This property is present when the dma address size + format cannot be derived using the method described in the + definition for the + “ibm,#dma-size-cells” property + in + . + + + + + + “ibm,#dma-address-cells” + + + + See definition column + + + Property name, to define the package’s dma address + format. The property value specifies the number of cells that + are used to encode the physical address field of dma-window + properties. This property is present when the dma address + format cannot be derived using the method described in the + definition for the + “ibm,#dma-address-cells” property in + . + + + + +
+
+ +
+ Logical LAN hcall()s + The receiver can set the virtual interrupt associated with its + Receive Queue to one of two modes using the H_VIO_SIGNAL hcall(). These + are: + + + + Disabled (An enqueue interrupt is not signaled.) + + + + Enabled (An enqueue interrupt is signaled on every + enqueue) + + + + Note: An enqueue is considered a pulse not a level. + The pulse then sets the memory element within the emulated interrupt + source controller. This allows the resetting of the interrupt condition + by simply issuing the H_EOI hcall() as is done with the PCI MSI + architecture rather than having to do an explicit interrupt reset as in + the case with PCI LSI architecture. + The interrupt mechanism, however, is capable of presenting only one + interrupt signal at a time from any given interrupt source. Therefore, no + additional interrupts from a given source are ever signaled until the + previous interrupt has been processed through to the issuance of an H_EOI + hcall(). Specifically, even if the interrupt mode is enabled, the effect + is to interrupt on an empty to non-empty transition of the queue. + +
+ H_REGISTER_LOGICAL_LAN + + + + Syntax: + + + + + + + Parameters: + + + + unit-address: As specified in the Logical LAN device tree node + “reg” property + + + + buf-list: I/O address of a 4 KB page (aligned) used to record + registered input buffers + + + + rec-queue: Buffer descriptor of a receive queue, specifying a + receive queue which is a multiple of 16 bytes in length and is 16 byte + aligned + + + + filter-list: I/O address of a 4 KB page aligned broadcast MAC + address filter list + + + + mac-address: The receive filter MAC address + + + + + + Semantics: + + + + Validate the Unit Address else H_Parameter + + + + Validate the I/O addresses of the buf-list and filter-list is in + the TCE and is 4K byte aligned else H_Parameter + + + + Validate the Buffer Descriptor of the receive queue buffer (I/O + addresses for entire buffer length starting at the specified I/O address + are translated by the RTCE table, length is a multiple of 16 bytes, and + alignment is on a 16 byte boundary) else H_Parameter. + + + + Initialize the one page buffer list + + + + Enqueue the receive queue buffer (set valid toggle to 0). + + + + Initialize the hypervisor’s receive queue enqueue pointer + and length variables for the virtual IOA associated with the Unit + Address. These variables are kept in terms of DMA addresses so that page + migration works and any remapping of TCEs is effective. + + + + Disable receive queue interrupts. + + + + Record the low order 6 bytes of mac-address for filtering future + incoming messages. + + + + Return H_Success. + + + +
+ +
+ H_FREE_LOGICAL_LAN + + + + Syntax: + + + + + + + Parameters: + + + + unit-address: Unit Address per device tree node + “reg” property. + + + + + + Semantics: + + + + Validate the Unit Address else H_Parameter + + + + Interlock/carefully manipulate tables so that H_SEND_LOGICAL_LAN + performs safely. + + + + Clear the associated page buffer list, prevent further + consumption of receive buffers and generation of receive + interrupts. + + + + Return H_Success. + + + + H_FREE_LOGICAL_LAN is the only valid mechanism to reclaim the + memory pages registered via H_REGISTER_LOGICAL_LAN. + + Implementation Note: If the hypervisor returns an + H_Busy, H_LongBusyOrder1mSec, or H_LongBusyOrder10mSec, software must + call H_FREE_LOGICAL_LAN again with the same parameters. Software may + choose to treat H_LongBusyOrder1mSec and H_LongBusyOrder10mSec the same + as H_Busy. The hypervisor, prior to returning H_Busy, + H_LongBusyOrder1mSec, or H_LongBusyOrder10mSec, will have placed the + virtual adapter in a state that will cause it to not accept any new work + nor surface any new virtual interrupts (no new frames will arrive, + etc.). + +
+ +
+ H_ADD_LOGICAL_LAN_BUFFER + + + + Syntax: + + + + + + + Parameters: + + + + unit-address: Unit Address per device tree node + “reg” property + + + + buf: Buffer Descriptor of new I/O buffer + + + + + + Semantics: + + + + Checks that unit address is OK else H_Parameter. + + + + Checks that I/O Address is within range of DMA window. + + + + Scans the buffer list for a pool of buffers of the length + specified in the Descriptor + + + + If one does not exist (and there is still room in the buffer + list, create a new pool entry else H_Resource). + + + + Uses enqueue procedure that is compatible with H_SEND_LOGICAL_LAN + hcall()’s dequeue procedure + + + + Implementation Note: Since the buffer queue is based upon I/O + addresses that are checked by H_SEND_LOGICAL_LAN, it is only necessary to + insure that the enqueue/dequeue are internally consistent. If the owning + OS corrupts his buffer descriptors or buffer queue pointers, this is + caught by H_SEND_LOGICAL_LAN and/or the corruption is contained within + the OS’s partition. + Architecture Note: Consideration was given to define the enqueue + algorithm and have the DD do the enqueue itself. However, no designs + presented themselves that eliminated the timing windows caused by adding + and removing pool lists without the introduction of OS/FW + interlocks. + +
+ +
+ H_FREE_LOGICAL_LAN_BUFFER + + + + Syntax: + + + + + + + Parameters: + + + + unit-address: Unit Address per device tree node + “reg” property. + + + + bufsize: The size of the buffer that is being requested to be + removed from the receive buffer pool. + + + + + + Semantics: + + + + Check that unit address is valid, else return H_Parameter. + + + + Scan the buffer list for a pool of buffers of the length + specified in bufsize, and return H_Not_Found if one does not + exist. + + + + Place an entry on receive queue for buffer of specified size, + with Control field Bit 1 set to 0, and return H_Success + + + +
+ +
+ H_SEND_LOGICAL_LAN + + + + Syntax: + + + + The H_Dropped return code indicates to the sender that one or more + intended receivers did not receive the message. + + + + Parameters: + + + + unit-address: Unit Address per device tree node + “reg” property + + + + buff-1: Buffer Descriptor #1 + + + + buff-2: Buffer Descriptor #2 + + + + buff-3: Buffer Descriptor #3 + + + + buff-4: Buffer Descriptor #4 + + + + buff-5: Buffer Descriptor #5 + + + + buff-6: Buffer Descriptor #6 + + + + continue-token: Used to continue a transfer if H_Busy is + returned. Set to 0 on the first call. If H_Busy is returned, then call + again but use the value returned in R4 from the previous call as the + value of continue-token. + + + + + + Semantics: + + + + If continue-token is non-zero, then do appropriate checks to see + that parameters and buffers are still valid, and pickup where the + previous transfer left off for the specified unit address, based on the + value of the continue-token. + + + + If continue-token is zero and if previous H_SEND_LOGICAL_LAN for + the specified unit address was suspended with H_Busy and never completed, + then cleanup the state from the previously suspended call before + proceeding. + + + + Verifies the VLAN number -- else H_Parameter. + + + + Proceeds down the 6 buffer descriptors until the first one that + has a length of 0 + + + + If the + “ibm,max-virtual-dma-size” property exist + in the + /vdevice node of the device tree, then if the length + is greater than the value of this property, return H_Parameter + + + + For the length of the buffer: + + + + Verifies the I/O buffer addresses translate through the + sender’s RTCE table else H_Parameter. + + + + + + + + Verifies the destination MAC address for the VLAN + + + + If MAC address is not cached and there exists a Trunk Adapter for + the VLAN, then flags the message as destined for the Trunk Adapter and + continues processing + + + + If MAC address is not cached and a Trunk Adapter does not exist + for the VLAN, then drop the message (H_Dropped) + + + + + + For each Destination MAC Address (broadcast MAC address turns + into multi-cast to all destinations on the specified VLAN): + + + + In the case of multicast MAC addresses the following algorithm + defines the members of the receiver class for a given VLAN: + For each logical lan IOA that would be a target for a broadcast + from the source IOA: + + + + If the receiving IOA is not enabled for non-broadcast multicast + frames then continue + + + + If the receiving IOA is not enabled for filtering non-broadcast + multicast frames then copy the frame to the IOA's receive buffer + Else + + + + If (lookup filter (table index)) then copy the frame to the + IOA's receive buffer + + + + Else if the receiving IOA is not enabled for filtering + non-broadcast multicast frames then copy the frame to the IOA's receive + buffer /*allows for races on filter insertion */ + + + + + + int lookup filter (table index) + + + + Firmware implementation designed algorithm + + + + + + + Searches the receiver’s receive queue for a suitable buffer + and atomically dequeues it: + + + + If no suitable buffer is found, the receiver’s dropped + packet counter (last 8 bytes of buffer list) is incremented and + processing proceeds to the next receiver if any. + + + + + + Copy the send data in to the selected receive buffer, build a + receive queue entry, and generate an interrupt to the receiver if the + interrupt is enabled. + + + + + + If any frames were dropped return H_Dropped else return + H_Success. + + + + Firmware Implementation Note: If during the + processing of the H_SEND_LOGICAL_LAN call, it becomes necessary to + temporarily suspend the processing of the call (for example, due to the + length of time it is taking to process the call), the firmware may return + a continuation token in R4, along with the return code of H_Busy. The + value of the continuation token is up to the firmware, and will be passed + back by the software as the continue-token parameter on the next call of + H_SEND_LOGICAL_LAN. + This hcall() interlocks with H_MIGRATE_DMA to allow for migration + of TCE mapped DMA pages. + Note: It is possible for either or both the sending + and receiving OS to modify its RTCE tables so as to affect the TCE + translations being actively used by H_SEND_LOGICAL_LAN. This is an error + condition on the part of the OS. Implementations need only insure that + such conditions do not corrupt memory in innocent partitions and should + not add path length to protect guilty partitions. By all means the path + length of H_GET_TCE and H_PUT_TCE should not be increased. If reasonably + possible, without significant path length addition, implementations + should: On send buffer translation corruption, return H_Parameter to the + sender and either totally drop the packet prior to reception, or if the + receive buffer has been processed past the point of transparent + recycling, mark the receive buffer as received in error in the receive + queue. On receive buffer translation corruption, terminate the data copy + to the receive buffer and mark the buffer as received in error in the + receive queue. + +
+ +
+ H_MULTICAST_CTRL + This hcall() controls the reception of non-broadcast multicast + packets (those with the high order address byte being odd but not the all + 1’s address). All implementations support the enabling and + disabling of the reception of all multicast packets on their V-LAN. + Additionally, the l-lan device driver through this call may ask the + firmware to filter multicast packets for it. That is, receive packets + only if they contain multicast addresses specified by the device driver. + The number of simultaneous multicast packet filters supported is + implementation dependent, and is specified in the + “ibm,mac-address-filters” property of the + l-lan device tree node. Therefore, the device driver must be prepared to + have any filter request fail, and fall back to enabling reception of all + multicast packets and filtering them in the device driver. Semantically, + the device driver may ask that the reception of multicast packets be + enabled or disabled, further if reception is enabled, they may be + filtered by only allowing reception of packets who’s mac address + matches one of the entries in the filter table. The call also manages the + contents of the mac address filter table. Individual mac addresses may be + added, or removed, and the filter table may be cleared. If the filter + table is modified by a call, there is the possibility that a packet may + be improperly filtered (one that was to be filtered out may get through + or one that should have gotten through may be dropped) this is done to + avoid adding extra locking to the packet processing code. In most cases + higher level protocols will handle the condition (since firmware + filtering is simply a performance optimization), if, however, a specific + condition requires complete accuracy, the device driver can disable + filtering prior to an update, do its own filtering (as would be required + if the number of receivers exceeded the number of filters in the filter + table) update the filter table, and then reenable filtering. + + + Syntax: + + + + + + + Parameters: + + + + unit-address: Unit Address per device tree node + “reg” property + + + + flags: Only bits 44-47 and 62-63 are defined all other bits + should be zero. + + + + multi-cast-address: Multicast MAC address, if flag bits 62 and 63 + are 01 or 10, else this parameter is ignored. + + + + Return value in register R4: + State of Enables and Count of MAC Filters in table. + Format: + + R = The value of the Receipt Enable bit + F = The value of the Filter Enable bit + MAC Filter Count -- 16 bit count of the number of MAC Filters in + the multicast filter table. + + + + Semantics: + + + + Validate the unit-address parameter else return + H_Parameter. + + + + Validate that no reserved flag bit = 1 else return + H_Parameter. + + + + If any bits are on in the high order two bytes of the MAC + parameter Return H_Parameter + + + + Modify Enables per specification if requested. + + + + Modify the Filter Table per specification if requested filtering + is disable during any filter table modification and filter enable state + restored after filter table modification). + + + + If don't modify RC=H_Success + + + + If Clear all: initialize the filter table, RC=H_Success + + + + If Add: + + + + If there is room in the table insert new MAC Filter entry, MAC + Filter count++, RC=H_Success + + + + Else RC=H_Constrained + + + + (duplicates are silently dropped -- filter count stays the same + RC=H_Success) + + + + + + If Remove: + + + + Locate the specified entry in the MAC Filter Table + + + + If Found remove the entry, MAC Filter count--, + RC=H_Success + + + + Else RC=H_Not_Found + + + + + + + + Load the Enable Bits into R4 bits 46 and 47 Load the MAC Filter + count into R4 Bits 48-63 + + + + Return RC + + + +
+ +
+ H_CHANGE_LOGICAL_LAN_MAC + This hcall() allows the changing of the virtual IOA’s MAC + address. + + + Syntax: + + + + + + + Parameters: + + + + unit-address: Unit Address per device tree node + “reg” property + + + + mac-address: The new receive filter MAC address + + + + + + Semantics: + + + + Validates the unit address, else H_Parameter + + + + Records the low order 6 bytes of mac-address for filtering future + incoming messages + + + + Returns H_Success + + + +
+ +
+ H_ILLAN_ATTRIBUTES + There are certain ILLAN attributes that are made visible to and can + be manipulated by partition software. The H_ILLAN_ATTRIBUTES hcall is + used to read and modify the attributes (see + ). + defines the attributes that are + visible and manipulatable. +   + + ILLAN Attributes + + + + + + + + + Bit(s) + + + + + Field Name + + + + + Definition + + + + + + + + 0-49 + + + Reserved + + +   + + + + + 50 + + + Checksum Offload Padded Packet Support + + + This bit is implemented when the ILLAN Checksum Offload + Padded Packet Support option is implemented. See + . + 0: Software must not request checksum offload, by setting + Bit 6 of the buffer descriptor (the No Checksum bit), for + packets that have been padded. + 1: Software may request checksum offload, by setting Bit + 6 of the buffer descriptor (the No Checksum bit), for packets + that have been padded. + + + + + 51 + + + Buffer Size Control + + + This bit is implemented when the ILLAN Buffer Size + Control option is implemented. This bit allows the partition + software to inhibit the use of too large of a buffer for + incoming packets, when a reasonable size buffer is not + available. The state of this bit cannot be changed between the + time that the ILLAN is registered by an H_REGISTER_LOGICAL_LAN + and it is deregistered by an H_FREE_LOGICAL_LAN. See also + . + 1: The hypervisor will keep a history of what buffer + sizes have been registered. When a packets arrives the history + is searched to find the smallest buffers size that will contain + the packet. If that buffer size is depleted then the packet is + dropped by the hypervisor (H_Dropped) instead of searching for + the next larger available buffer. + 0: This is the initial value. When a packet arrives, the + available buffers are searched for the smallest available + buffer that will hold the packet, and the packet is not dropped + unless no buffer is available in which the packet will + fit. + + + + + 52-55 + + + Trunk Adapter Priority + + + This field is implemented for a VIOA whenever the ILLAN + Backup Trunk Adapter option is implemented and the VIOA is a + Trunk Adapter (the Active Trunk Adapter bit will be + implemented, also, in this case). If this field is a 0, then + the either the ILLAN Backup Trunk Adapter option is not + implemented or it is implemented but this VIOA is not a Trunk + Adapter. A non-0 value in this field reflects the priority of + the node in the backup Trunk Adapter hierarchy, with a value of + 1 being the highest (most favored) priority, the value of 2 + being the next highest priority, and so on. This field may or + may not be changeable by the partition firmware via the + H_ILLAN_ATTRIBUTES hcall() (platform implementation dependent). + If not changeable, then attempts to change this field will + result in a return code of H_Constrained. See also + . + + + + + 56-60 + + + Reserved + + +   + + + + + 61 + + + TCP Checksum Offload Support for IPv6 + + + This bit is implemented for a VIOA whenever the ILLAN + Checksum Offload Support option is implemented for TCP, the + IPv6 protocol, and the following extension headers: + Hop-by-Hop Options + Routing + Destination Options + Authentication + Mobility + This bit is initially set to 0 by the firmware and the + ILLAN DD may attempt to set it to a 1 by use of the + H_ILLAN_ATTRIBUTES hcall() if the DD supports the option for + TCP and IPv6. Firmware will not allow changing the state of + this bit if it does not support Checksum Offload Support for + TCP for IPv6 for the VIOA (H_Constrained would be returned in + this case from the H_ILLAN_ATTRIBUTES hcall() when this bit is + a 1 in the set-mask). This state of this bit cannot be changed + between the time that the ILLAN is registered by an + H_REGISTER_LOGICAL_LAN and it is deregistered by an + H_FREE_LOGICAL_LAN. See + for more + information. + 1: The partition software has indicated that it supports + the ILLAN Checksum Offload Support option for TCP and IPv6 + protocol and for the above stated extension headers by using + the H_ILLAN_ATTRIBUTES hcall() with this bit set to a 1 in the + set-mask, and the firmware has verified that it supports this + protocol for the option for the VIOA. + 0: The partition software has not indicated that it + supports the ILLAN Checksum Offload Support option for TCP and + IPv6 protocol and for the above stated extension headers by + using the H_ILLAN_ATTRIBUTES hcall() with this bit set to a 1 + in the set-mask, or it has but the firmware does not support + the option, or supports the option but not for this protocol or + for this VIOA. + + + + + 62 + + + TCP Checksum Offload Support for IPv4 + + + This bit is implemented for a VIOA whenever the ILLAN + Checksum Offload Support option is implemented for TCP and the + IPv4 protocol. This bit is initially set to 0 by the firmware + and the ILLAN DD may attempt to set it to a 1 by use of the + H_ILLAN_ATTRIBUTES hcall() if the DD supports the option for + TCP and IPv4. Firmware will not allow changing the state of + this bit if it does not support Checksum Offload Support for + TCP or IPv4 for the VIOA (H_Constrained would be returned in + this case from the H_ILLAN_ATTRIBUTES hcall() when this bit is + a 1 in the set-mask). This state of this bit cannot be changed + between the time that the ILLAN is registered by an + H_REGISTER_LOGICAL_LAN and it is deregistered by an + H_FREE_LOGICAL_LAN. See + for more + information. + 1: The partition software has indicated that it supports + the ILLAN Checksum Offload Support option for TCP and IPv4 + protocol by using the H_ILLAN_ATTRIBUTES hcall() with this bit + set to a 1 in the set-mask, and the firmware has verified that + it supports this protocol for the option for the VIOA. + 0: The partition software has not indicated that it + supports the ILLAN Checksum Offload Support option for TCP and + IPv4 by using the H_ILLAN_ATTRIBUTES hcall() with this bit set + to a 1 in the set-mask, or it has but the firmware does not + support the option, or supports the option but not for this + protocol or for this VIOA. + + + + + 63 + + + Active Trunk Adapter + + + This bit is implemented for a VIOA whenever the ILLAN + Backup Trunk Adapter option is implemented and the VIOA is a + Trunk Adapter (the Trunk Adapter Priority field will be + implemented, also, in this case). + This bit is initially set to 0 by the firmware for an + inactive Trunk Adapter. + This bit is initially set to 1 by the firmware for an + active Trunk Adapter. + This bit will be changed from a 0 to a 1 when all the + following a true: (1) the partition software (via the + H_ILLAN_ATTRIBUTES hcall() with this bit set to a 1 in the + set-mask) attempts to set this bit to a 1, (2) the firmware + supports the Backup Trunk Adapter option, (3) the VIOA is a + Trunk Adapter. + This bit will be changed from a 1 to a 0 by the firmware + when another Trunk Adapter has had its Active Trunk Adapter bit + changed from a 0 to a 1. + See + for more + information. + 1: The VIOA is the active Trunk Adapter. + 0: The VIOA is not an active Trunk Adapter or is not a + Trunk Adapter at all. + + + + +
+ + + + R1--1. + + + If the H_ILLAN_ATTRIBUTES hcall is + implemented, then it must implement the attributes as they are defined in + and the syntax and semantics as + defined in + . + + + + + R1--2. + + + The H_ILLAN_ATTRIBUTES hcall must ignore + bits in the set-mask and reset-mask which are not implemented for the + specified unit-address and must process as an exception those which + cannot be changed for the specified unit-address (H_Constrained + returned), and must return the following for the ILLAN Attributes in + R4: + + + + A value of 0 for unimplemented bit positions. + + + + The resultant field values for implemented fields. + + + + + + + + + Syntax: + + + + + + + Parameters: + unit-address: Unit Address per device tree node + “reg” property. The ILLAN unit address on + which this Attribute modification is to be performed. + reset-mask: The bit-significant mask of bits to be reset in the + ILLAN’s Attributes (the reset-mask bit definition aligns with the + bit definition of the ILLAN’s Attributes, as defined in + ). The complement of the + reset-mask is ANDed with the ILLAN’s Attributes, prior to applying + the set-mask. See semantics for more details on any field-specific + actions needed during the reset operations. If a particular field + position in the ILLAN Attributes is not implemented, then the + corresponding bit(s) in the reset-mask are ignored. + set-mask: The bit-significant mask of bits to be set in the + ILLAN’s Attributes (the set-mask bit definition aligns with the bit + definition of the ILLAN’s Attributes, as defined in + ). The set-mask is ORed with + the ILLAN’s Attributes, after to applying the reset-mask. See + semantics for more details on any field-specific actions needed during + the set operations. If a particular field position in the ILLAN + Attributes is not implemented, then the corresponding bit(s) in the + set-mask are ignored. + + + + Semantics: + + + + Validate that Unit Address belongs to the partition, else + H_Parameter. + + + + Reset/set the bits in the ILLAN Attributes, as indicated by the + rest-mask and set-mask except as indicated in the following + conditions. + + + + If the Buffer Size Control bit is trying to be changed from a 0 + to a 1 and any of the following is true, then do not allow the change + (H_Constrained will be returned): + + + + The ILLAN is active. That is, the ILLAN has been registered + (H_REGISTER_LOGICAL_LAN) but has not be deregistered + (H_FREE_LOGICAL_LAN). + + + + The firmware does not support the ILLAN Buffer Size Control + option. + + + + + + If the Buffer Size Control bit is trying to be changed from a 1 + to a 0 and any of the following is true, then do not allow the change + (H_Constrained will be returned): + + + + The ILLAN is active. That is, the ILLAN has been registered + (H_REGISTER_LOGICAL_LAN) but has not be deregistered + (H_FREE_LOGICAL_LAN). + + + + + + If either the TCP Checksum Offload Support for IPv4 bit or TCP + Checksum Offload Support for IPv6 bit is trying to be changed from a 0 to + a 1 and any of the following is true, then do not allow the change + (H_Constrained will be returned): + + + + The ILLAN is active. That is, the ILLAN has been registered + (H_REGISTER_LOGICAL_LAN) but has not be deregistered + (H_FREE_LOGICAL_LAN). + + + + The firmware does not support the ILLAN Checksum Offload Support + option or supports it, but not for the specified protocol(s) or does not + support it for this VIOA. + + + + + + If the TCP Checksum Offload Support for IPv4 bit or TCP Checksum + Offload Support for IPv6 bit is trying to be changed from a 1 to a 0 and + any of the following is true, then do not allow the change (H_Constrained + will be returned): + + + + The ILLAN is active. That is, the ILLAN has been registered + (H_REGISTER_LOGICAL_LAN) but has not be deregistered + (H_FREE_LOGICAL_LAN). + + + + + + If the Active Trunk Adapter bit is trying to be changed from a 0 + to a 1 and any of the following is true, then do not allow the change + (H_Constrained will be returned): + + + + The firmware does not support the ILLAN Backup Trunk Adapter + option or this VIOA is not a Trunk Adapter. + + + + + + If the Active Trunk Adapter bit is trying to be changed from a 1 + to a 0, then return H_Parameter. + + + + If the Active Trunk Adapter bit is changed from a 0 to a 1 for a + VIOA, then also set any previously active Trunk Adapter’s Active + Trunk Adapter bit from a 1 to a 0. + + + + If the Trunk Adapter Priority field is trying to be changed from + 0 to a non-0 value, then return H_Parameter. + + + + If the Trunk Adapter Priority field is trying to be changed from + a non-0 value to another non-0 value and either the parameter is not + changeable or the change is not within the platform allowed limits, then + do not allow the change (H_Constrained will be returned). + + + + Load R4 with the value of the ILLAN’s Attributes, with any + unimplemented bits set to 0, and if all requested changes were made then + return H_Success, otherwise return H_Constrained. + + + +
+ +
+ Other hcall()s extended or used by the Logical LAN + Option + + +
+ H_VIO_SIGNAL + The H_VIO_SIGNAL hcall() is used by multiple VIO options. +
+ +
+ H_EOI + The H_EOI hcall(), when specifying an interrupt source number + associated with an interpartion logical LAN IOA, incorporates the + interrupt reset function. +
+ +
+ H_XIRR + This call is extended to report the virtual interrupt source number + associated with virtual interrupts associated with an ILLAN IOA. +
+ +
+ H_PUT_TCE + This standard hcall() is used to manage the ILLAN IOA’s I/O + translations. +
+ +
+ H_GET_TCE + This standard hcall() is used to manage the ILLAN IOA’s I/O + translations. +
+ +
+ H_MIGRATE_DMA + This hcall() is extended to serialize with the H_SEND_LOGICAL_LAN + hcall() to allow for migration of TCE mapped DMA pages. +
+
+
+ +
+ RTAS Calls Extended or Used by the Logical LAN + Option + Platforms may combine the Logical LAN option with most other LoPAR + options such as dynamic reconfiguration by including the appropriate OF + properties and extending the associated firmware calls. However, the + ibm,set-xive, ibm,get-xive, ibm,int-off, + and + ibm,int-on RTAS calls are extended as part of the + base support. +
+ +
+ Interpartition Logical LAN Requirements + The following requirements are mandated for platforms implementing + the ILLAN option. + + + + R1--1. + + For the ILLAN option: The platform must interpret + logical LAN buffer descriptors as defined in + . + + + + + R1--2. + + For the ILLAN option: The platform must reject + logical LAN buffer descriptors that are not 8 byte aligned. + + + + + R1--3. + + For the ILLAN option: The platform must interpret the + first byte of a logical LAN buffer descriptor as a control byte, the high + order bit being the valid bit. + + + + + R1--4. + + For the ILLAN option: The platform must set the next + to high order bit of the control byte of the logical LAN buffer + descriptor for the receive queue to the inverse of the value currently + being used to indicate a valid receive queue entry. + + + + + R1--5. + + For the ILLAN option: The platform must interpret the + 2nd through 4th bytes of a logical LAN buffer descriptor as the binary + length of the buffer in I/O space (relative to the TCE mapping table + defined by the logical IOA’s + “ibm,my-dma-window” property). + + + + + R1--6. + + For the ILLAN option: The platform must interpret the + 5th through 8th bytes of a logical LAN buffer descriptor as the binary + beginning address of the buffer in I/O space (relative to the TCE mapping + table defined by the logical IOA’s + “ibm,my-dma-window” property). + + + + + R1--7. + + For the ILLAN option: The platform must interpret + logical LAN Buffer Lists as defined in + . + + + + + R1--8. + + For the ILLAN option: The platform must reject + logical LAN Buffer Lists that are not mapped relative to the TCE mapping + table defined by the logical IOA’s + “ibm,my-dma-window” property. + + + + + R1--9. + + For the ILLAN option: The platform must reject + logical LAN buffer lists that are not 4 KB aligned. + + + + + R1--10. + + For the ILLAN option: The platform must interpret the + first 8 bytes of a logical LAN buffer list as a buffer descriptor for the + logical IOA’s Receive Queue. + + + + + R1--11. + + For the ILLAN option: The platform must interpret the + logical LAN receive queue as defined in + . + + + + + R1--12. + + For the ILLAN option: The platform must reject a + logical LAN receive queue that is not mapped relative to the TCE mapping + table defined by the logical IOA’s + “ibm,my-dma-window” property. + + + + + R1--13. + + For the ILLAN option: The platform must reject a + logical LAN receive queue that is not aligned on a 4 byte + boundary. + + + + + R1--14. + + For the ILLAN option: The platform must reject a + logical LAN receive queue that is not an exact multiple of 12 bytes + long. + + + + + R1--15. + + For the ILLAN option: The platform must manage the + logical LAN receive queue as a circular buffer. + + + + + R1--16. + + For the ILLAN option: The platform must enqueue 12 + byte logical LAN receive queue entries when a new message is + received. + + + + + R1--17. + + For the ILLAN option: + The platform must + set the last 8 bytes of the logical LAN receive queue entry to the value + of the user supplied correlator found in the first 8 bytes of the logical + LAN receive buffer used to contain the message before setting the first 4 + bytes of the logical LAN receive queue entry. + + + + + R1--18. + + For the ILLAN option: + The platform must + set the first 4 bytes of the logical LAN receive queue entry such that + the first byte contains the control field (high order bit the inverse of + the valid toggle in the receive queue buffer descriptor, next bit to a + one if the message payload is valid) and the last 3 bytes contains the + receive message length, after setting the correlator field in the last 8 + bytes per Requirement + . + + + + + R1--19. + + For the ILLAN option: The platform must when crossing + from the end of the logical LAN receive queue back to the beginning + invert the value of the valid toggle in the receive queue buffer + descriptor. + + + + + R1--20. + + For the ILLAN option: The platform’s OF must + disable interrupts from the logical LAN IOA before initially passing + control to the booted client program. + + + + + R1--21. + + For the ILLAN option: The platform must present (as + appropriate per RTAS control of the interrupt source number) the + partition owning a logical LAN receive queue the appearance of an + interrupt, from the interrupt source number associated, through the OF + device tree node, with the virtual device, when a new entry is enqueued + to the logical LAN receive queue and the last interrupt mode set via the + H_VIO_SIGNAL was “Enabled”, unless a previous interrupt from + the interrupt source number is still outstanding. + + + + + R1--22. + + For the ILLAN option: The platform must NOT present + the partition owning a logical LAN receive queue the appearance of an + interrupt, from the interrupt source number associated, through the OF + device tree node, with the virtual device, if the last interrupt mode set + via the H_VIO_SIGNAL was “Disabled”, unless a previous + interrupt from the interrupt source number is still outstanding. + + + + + R1--23. + + For the ILLAN option: The platform must interpret + logical LAN receive buffers as defined in + . + + + + + R1--24. + + For the ILLAN option: The platform must reject a + logical LAN receive buffer that is not mapped relative to the TCE mapping + table defined by the logical IOA’s + “ibm,my-dma-window” property. + + + + + R1--25. + + For the ILLAN option: The platform must reject a + logical LAN receive buffer that is not aligned on a 4 byte + boundary. + + + + + R1--26. + + For the ILLAN option: The platform must reject a + logical LAN receive buffer that is not a minimum of 16 bytes long. + + + + + R1--27. + + For the ILLAN option: The platform must not modify + the first 8 bytes of a logical LAN receive buffer, this area is reserved + for a user supplied correlator value. + + + + + R1--28. + + For the ILLAN option: The platform must not allow + corruption caused by a user modifying the logical LAN receive buffer from + escaping the user partition (except as a side effect of some another user + partition I/O operation). + + + + + R1--29. + + For the ILLAN option: The platform’s + l-lan OF device tree node must contain properties as + defined in + . (Other standard I/O adapter + properties are permissible as appropriate.) + + + + + R1--30. + + For the ILLAN option: The platform must implement the + H_REGISTER_LOGICAL_LAN hcall() as defined in + . + + + + + R1--31. + + For the ILLAN option: The platform must implement the + H_FREE_LOGICAL_LAN hcall() as defined in + . + + + + + R1--32. + + For the ILLAN option: The platform must implement the + H_ADD_LOGICAL_LAN_BUFFER hcall() as defined in + . + + + + + R1--33. + + For the ILLAN option: The platform must implement the + H_SEND_LOGICAL_LAN hcall() as defined in + . + + + + + R1--34. + + For the ILLAN option: The platform must implement the + H_SEND_LOGICAL_LAN hcall() such that an OS requested modification to an + active RTCE table entry cannot corrupt memory in other partitions. + (Except indirectly as a result of some other of the partition’s I/O + operations.) + + + + + R1--35. + + For the ILLAN option: The platform must implement the + H_CHANGE_LOGICAL_LAN_MAC hcall() as defined in + . + + + + + R1--36. + + For the ILLAN option: The platform must implement the + H_VIO_SIGNAL hcall() as defined in + . + + + + + R1--37. + + For the ILLAN option: The platform must implement the + extensions to the H_EOI hcall() as defined in + . + + + + + R1--38. + + For the ILLAN option: The platform must implement the + extensions to the H_XIRR hcall() as defined in + . + + + + + R1--39. + + For the ILLAN option: The platform must implement the + H_PUT_TCE hcall(). + + + + + R1--40. + + For the ILLAN option: The platform must implement the + H_GET_TCE hcall(). + + + + + R1--41. + + For the ILLAN option: The platform must implement the + extensions to the H_MIGRATE_DMA hcall() as defined in + . + + + + + R1--42. + + For the ILLAN option: The platforms must emulate the + standard PowerPC External Interrupt Architecture for the interrupt source + numbers associated with the virtual devices via the standard RTAS and + hypervisor interrupt calls. + + + +
+ +
+ Logical LAN Options + The ILLAN option has several sub-options. The hypervisor reports to + the partition software when it supports one or more of these options, and + potentially other information about those option implementations, via the + implementation of the appropriate bits in the ILLAN Attributes, which can + be ascertained by the H_ILLAN_ATTRIBUTES hcall(). The same hcall() may be + used by the partition software to communicate back to the firmware the + level of support for those options where the firmware needs to know the + level of partition software support. The + “ibm,illan-options” property will exist + in the VIOA’s Device Tree node, indicating that the + H_ILLAN_ATTRIBUTES hcall() is implemented, and therefore that one or more + of the options are implemented. The following sections give more + details. + +
+ ILLAN Backup Trunk Adapter Option + The ILLAN Backup Trunk Adapter option allows the platform to + provide one or more backups to a Trunk Adapter, for reliability purposes. + Implementation of the ILLAN Backup Trunk Adapter option is specified to + the partition by the existence of the + “ibm,illan-options” property in the + VIOA’s Device Tree node and a non-0 value in the ILLAN Attributes + Backup Trunk adapter Priority field. A Trunk Adapter becomes the active + Trunk Adapter by calling H_ILLAN_ATTRIBUTES hcall() and setting its + Active Trunk Adapter bit. Only one Trunk Adapter is active for a VLAN at + a time. The protocols which determine which Trunk Adapter is active at + any particular time, is beyond the scope of this architecture. + + + + R1--1. + + For the ILLAN Backup Trunk Adapter option: The + platform must implement the ILLAN option. + + + + + R1--2. + + For the ILLAN Backup Trunk Adapter option: The + platform must implement the H_ILLAN_ATTRIBUTES hcall(). + + + + + R1--3. + + For the ILLAN Backup Trunk Adapter option: The + platform must implement the + “ibm,illan-options” and + “ibm,trunk-adapter” properties in all the + Trunk Adapter nodes of the Device Tree. + + + + + R1--4. + + For the ILLAN Backup Trunk Adapter option: The + platform must implement the Active Trunk Adapter bit and the Backup Trunk + Adapter Priority field in the ILLAN Attributes, as defined in + , for all Trunk Adapter + VIOAs. + + + + + R1--5. + + For the ILLAN Backup Trunk Adapter option: The + platform must allow only one Trunk Adapter to be active for a VLAN at any + given time, and must: + + + + Make the determination of which one is active by whichever was + the most recent one to set its Active Trunk Adapter bit in their ILLAN + Attributes. + + + + Turn off the Active Trunk Adapter bit in the ILLAN Attributes + for a Trunk Adapter when it is removed from the active Trunk Adapter + state. + + + + + +
+ +
+ ILLAN Checksum Offload Support Option + This option allows for the support of IOAs that do checksum offload + processing. This option allows for support at one end (client or server) + but not the other, on a per-protocol basis, with the hypervisor + generating the checksum when the client supports offload but the server + does not, and the operation is a send from the client. + +
+ General + The H_ILLAN_ATTRIUBTES hcall is used to establish the common set of + checksum offload protocols to be supported between the firmware and the + partition software. The firmware indicates support for H_ILLAN_ATTRIBUTES + via the + “ibm,illan-options” property in the + VIOA’s Device Tree node. The partition software can determine which + of the Checksum Offload protocols (if any) that the firmware supports by + either attempting to set the bits in the ILLAN Attributes of the + protocols that the partition software supports or by calling the hcall() + with reset-mask and set-mask parameters of all-0’s (the latter + being just a query and not a request to support anything between the + partition and the firmware). + Two bits in the control field of the first buffer descriptor + specify which operations do not contain a checksum and which have had + their checksum already verified. See + . These two bits get + transferred to the corresponding control field of the Receive Queue + Entry, with the exception that the H_SEND_LOGICAL_LAN hcall will + sometimes set these to 0b00 (see + ). + + + + R1--1. + + + For the ILLAN Checksum Offload Support option: The + platform must do all the following: + + + + Implement the ILLAN option. + + + + Implement the H_ILLAN_ATTRIBUTES hcall(). + + + + Implement the + “ibm,illan-options” property in the + VIOA’s Device Tree node. + + + + Implement the appropriate Checksum Offload Support bit(s) of the + ILLAN Attributes, as defined in + . + + + + Software Implementation Note: Fragmentation and + encryption are not supported when the No Checksum bit of the Buffer + Descriptor is set to a 1. + + + +
+ +
+ H_SEND_LOGICAL_LAN Semantic Changes + There are several H_SEND_LOGICAL_LAN semantic changes required for + the ILLAN Checksum Offload Support option. See + for the base semantics. + + + + R1--1. + + + For the ILLAN Checksum Offload Support option: The + H_SEND_LOGICAL_LAN semantics must be changed as follows: + + + + As shown in + , and for multi-cast + operations, the determination in this table must be applied for each + destination. + + + + If the No Checksum bit is set to a 1 in the first buffer + descriptor and the adapter is not a Trunk Adapter, and the source MAC + address does not match the adapter's MAC address, then drop the + packet. + + + +   + + Summary of H_SEND_LOGICAL_LAN Semantics with Checksum + Offload + + + + + + + + + + + + Has Sender Set the Appropriate Checksum + Offload Support bit in the ILLAN Attributes for the Protocol + Being Used? + + + + + Has Receiver Set the Appropriate + Checksum Offload Support bit in the ILLAN Attributes for the + Protocol Being Used? + + + + + No Checksum bit in the Buffer + Descriptor + + + + + Checksum Good bit in the Buffer + Descriptor + + + + + H_SEND_LOGICAL_LAN Additional + Semantics + + + + + Receiver DD Additional + Requirements + + + + + + + + no + + + - + + + 0 + + + 0 + + + None. + + + None. + + + + + no + + + - + + + Either bit non-0 + + + Return H_Parameter + + +   + + + + + yes + + + - + + + 0 + + + 0 + + + None. + + + None. + + + + + yes + + + no + + + 0 + + + 1 + + + Set the No Checksum and Checksum Good bits in the Buffer + Descriptor to 00 on transfer. + + + None. + + + + + yes + + + no + + + 1 + + + 1 + + + Generate checksum and set the No Checksum and Checksum + Good bits in the Buffer Descriptor to 00 on transfer. + + + None. + + + + + yes + + + yes + + + 0 + + + 1 + + + None. + + + Do not need to do checksum checking. + + + + + yes + + + yes + + + 1 + + + 1 + + + None. + + + Do not need to do checksum checking. Generate checksum if + packet is to be passed on to an external LAN (may be done by + the IOA or by the DD). + + + + + - + + + - + + + 1 + + + 0 + + + Return H_Parameter + + +   + + + + + yes + + + - + + + 01 or 11 and packet type not supported by the hypervisor, + as indicated by the value returned by the H_ILLAN_ATTRIBUTES + hcall() + + + Return H_Parameter + + +   + + + + +
+ + + + + R1--2. + + + For the ILLAN Checksum Offload Support option: The + Receiver DD Additional Requirements shown in + must be implemented. + + + + + R1--3. + + + For the ILLAN Checksum Offload Support option: When + the caller of H_SEND_LOGICAL_LAN has set the No Checksum bit in the + Control field to a 1, then they must also have set the checksum field in + the packet to 0. + + + + +
+ +
+ Checksum Offload Padded Packet Support Option + Firmware may or may not support checksum offload for IPv4 packets + that have been padded. The Checksum Offload Padded Packet Support bit of + the ILLAN Attributes specifies whether or not this option is + supported. + + + + R1--1. + + + For the Checksum Offload Padded Packet Support + Option: The platform must do all the following: + + + + Implement the ILLAN Checksum Offload Support option. + + + + Implement the Checksum Offload Padded Support bit of the ILLAN + Attributes, as defined in + , and set that bit to a value + of 1. + + + + + + +
+
+ +
+ ILLAN Buffer Size Control Option + It is the partition software’s responsibility to keep + firmware supplied with enough buffers to keep packets from being dropped. + The ILLAN Buffer Size Control option gives the partition software a way + to prevent a flood of small packets from consuming buffers that have been + allocated for larger packets. + When this option is implemented and the Buffer Size Control bit in + the ILLAN Attributes is set to a 1 for the VLAN, the hypervisor will keep + a history of what buffer sizes have been registered. Then, when a packets + arrives the history is searched to find the smallest buffer size that + will contain the packet. If that buffer size is depleted then the packet + is dropped by the hypervisor (H_Dropped) instead of searching for the + next larger available buffer. + +
+ General + The following are the general requirements for this option. For + H_SEND_LOGICAL_LAN changes, see + . + + + + R1--1. + + + For the ILLAN Buffer Size Control option: The + platform must do all the following: + + + + Implement the ILLAN option. + + + + Implement the H_ILLAN_ATTRIBUTES hcall(). + + + + Implement the + “ibm,illan-options” property in the + VIOA’s Device Tree node. + + + + Implement the Buffer Size Control bit of the ILLAN Attributes, + as defined in + . + + + + + + +
+ +
+ H_SEND_LOGICAL_LAN Semantic Changes + The following are the required semantic changes to the + H_SEND_LOGICL_LAN hcall(). + + + + R1--1. + + + For the ILLAN Buffer Size Control option: When the + Buffer Size Control bit of the target of an H_SEND_LOGIC_LAN hcall() is + set to a 1, then the firmware for the H_SEND_LOGICAL_LAN hcall() must not + just search for any available buffer into which the packet will fit, but + must instead only place the packet into the receiver’s buffer if + there is an available buffer of the smallest size previously registered + by the receiver which will fit the packet, and must drop the packet for + that target otherwise. + + + +
+
+
+
+ +
+ Virtual SCSI (VSCSI) + Virtual SCSI (VSCI) support is provided by code running in a server + partition that uses the mechanisms of the Reliable Command/Response + Transport and Logical Remote DMA of the Synchronous VIO Infrastructure to + service I/O requests for code running in a client partition, such that, the + client partition appears to enjoy the services of its own SCSI adapter (see + + ). The terms server and client + partitions refer to platform partitions that are respectively servers and + clients of requests, usually I/O operations, using the physical I/O + adapters (IOAs) that are assigned to the server partition. This allows a + platform to have more client partitions than it may have physical I/O + adapters because the client partitions share I/O adapters via the server + partition. + The VSCSI architecture is built upon the architecture specified in + the following sections: + + + + + + + + + + + + + + + +
+ VSCSI General + This section contains an informative outline of the architectural + intent of the use of the Synchronous VIO Infrastructure to provide VSCSI + support, along with a few architectural requirements. Other + implementations of the server and client partition code, consistent with + this architecture, are possible and may be preferable. + The architectural metaphor for the VSCSI subsystem is that the + server partition provides the virtual equivalent of a single SCSI + DASD/Media string via each VSCSI server virtual IOA. The client partition + provides the virtual equivalent of a single port SCSI adapter via each + VSCSI client IOA. The platform, through the partition definition, + provides means for defining the set of virtual IOA’s owned by each + partition and their respective location codes. The platform also + provides, through partition definition, instructions to connect each + client partition’s VSCSI client IOA to a specific server + partition’s VSCSI server IOA. That is, the equivalent of connecting + the adapter cable to the specific DASD/Media string. The mechanism for + specifying this partition definition is beyond the scope of this + architecture. The human readable handle associated with the partition + definition of virtual IOAs and their associated interconnection and + resource configuration is the virtual location code. The OF unit address + (Unit ID) remains the invariant handle upon which the + OS builds its “physical to logical” configuration. + The client partition’s device tree contains one or more nodes + notifying the partition that it has been assigned one or more virtual + adapters. The node’s + “type” and + “compatible” properties notify the + partition that the virtual adapter is a VSCSI adapter. The + unit address of the node is used by the client + partition to map the virtual device(s) to the OS’s corresponding + logical representations. The + “ibm,my-dma-window” property communicates + the size of the RTCE table window panes that the hypervisor has + allocated. The node also specifies the interrupt source number that has + been assigned to the Reliable Command/Response Transport connection and + the RTCE range that the client partition device driver may use to map its + memory for access by the server partition via Logical Remote DMA. The + client partition, uses the four hcall()s associated with the Reliable + Command/Response Transport facility to register and deregister its CRQ, + manage notification of responses, and send command requests to the server + partition. + The server partition’s device tree contains one or more + node(s) notifying the partition that it is requested to supply VSCSI + services for one or more client partitions. The unit address ( + Unit ID) of the node is used by the server partition + to map to the local logical devices that are represented by this VSCSI + device. The node also specifies the interrupt source number that has been + assigned to the Reliable Command/Response Transport connection and the + RTCE range that the server partition device driver may use for its copy + Logical Remote DMA. The server partition uses the four hcall()s + associated with the Reliable Command/Response Transport facility to + register and deregister its Command request queue, manage notification of + new requests, and send responses back to the client partition. In + addition, the server partition uses the hcall()s of the Logical Remote + DMA facility to manage the movement of commands and data associated with + the client requests. + The client partition, upon noting the device tree entry for the + virtual adapter, loads the device driver associated with the value of the + + “compatible” property. The device driver, + when configured and opened, allocates memory for its CRQ (an array, large + enough for all possible responses, of 16 byte elements), pins the queue + and maps it into the I/O space of the RTCE window specified in the + “ibm,my-dma-window” property using the + standard kernel mapping services that subsequently use the H_PUT_TCE + hcall(). The queue is then registered using the H_REG_CRQ hcall(). Next, + I/O request control blocks (within which the I/O requests commands are + built) are allocated, pinned, and mapped into I/O address space. Finally, + the device driver registers to receive control when the interrupt source + specified in the virtual IOA’s device tree node signals. + Once the CRQ is setup, the device driver queues an Initialization + Command/Response with the second byte of “Initialize” in + order to attempt to tell the hosting side that everything is setup on the + hosted side. The response to this send may be that the send has been + dropped or has successfully been sent. If successful, the sender should + expect back an Initialization Command/Response with a second byte of + “Initialization Complete,” at which time the communication + path can be deemed to be open. If dropped, then the sender waits for the + receipt of an Initialization Command/Response with a second byte of + “Initialize,” at which time an “Initialization + Complete” message is sent, and if that message is sent + successfully, then the communication path can be deemed to be + open. + When the VSCSI Adapter device driver receives an I/O request from + one of the SCSI device head drivers, it executes the following sequence. + First an I/O request control block is allocated. Then it builds the SCSI + request within the control block, adds a correlator field (to be returned + in the subsequent response), I/O maps any target memory buffers and + places their DMA descriptors into the I/O request control block. With the + request constructed in the I/O request control block, the driver + constructs a DMA descriptor (Starting Offset, and length) representing + the I/O request within the I/O request control block. Lastly, the driver + passes the I/O request’s DMA descriptor to the server partition + using the H_SEND_CRQ hcall(). Provided that the H_SEND_CRQ hcall() + succeeds, the VSCSI Adapter device driver returns, waiting for the + response interrupt indicating that a response has been posted by the + server partition to the device driver’s response queue. The + response queue entry contains the summary status and request correlator. + From the request correlator, the device driver accesses the I/O request + control block, and from the summary status, the device driver determines + how to complete the processing of the I/O request. + Notice that the client partition only uses the Reliable + Command/Response Transport primitives; it does not use the Logical Remote + DMA primitives. Since the server partition’s RTCE tables are not + authorized for access by the client partition, any attempt by the client + partition to modify server partition memory would be prevented by the + hypervisor. RTCE table access is granted on a connection by connection + basis (client/server virtual device pair). If a client partition happens + to be serving some other logical device, then the partition is entitled + to use Logical Remote DMA for the virtual devices that is serving. + The server partition, upon noting the device tree entry for the + virtual adapter, loads the device driver associated with the value of the + + “compatible” property. The device driver, + when configured and opened, allocates memory for its request queue (an + array, large enough for all possible outstanding requests, of 16 byte + elements). The driver then pins the queue and maps it into I/O space, via + the kernel’s I/O mapping services that invoke the H_PUT_TCE + hcall(), using the first window pane specified in the + “ibm,my-dma-window” property. The queue + is then registered using the H_REG_CRQ hcall(). Next, I/O request control + blocks (within which the I/O request commands are built) are allocated, + pinned, and I/O mapped. Finally the device driver registers to receive + control when the interrupt source specified in the virtual IOA’s + device tree node signals. + Once the CRQ is setup, the device driver queues an Initialization + Command/Response with the second byte of “Initialize” in + order to attempt to tell the hosted side that everything is setup on the + hosting side. The response to this send may be that the send has been + dropped or has successfully been sent. If successful, the sender should + expect back an Initialization Command/Response with a second byte of + “Initialization Complete,” at which time the communication + path can be deemed to be open. If dropped, then the sender waits for the + receipt of an Initialization Command/Response with a second byte of + “Initialize,” at which time an “Initialization + Complete” message is sent, and if that message is sent + successfully, then the communication path can be deemed to be + open. + When the server partition’s device driver receives an I/O + request from its corresponding client partition’s VSCSI adapter + drivers, it is notified via the interrupt registered for above. The + server partition’s device driver selects an I/O request control + block for the requested operation. It then uses the DMA descriptor from + the request queue element to transfer the SCSI request from the client + partition’s I/O request control block to its own (allocated above), + using the H_COPY_RDMA hcall() through the second window pane specified in + the + “ibm,my-dma-window” property. The server + partition’s device driver then uses kernel services, that are + extended, to register the I/O request’s DMA descriptors into + extended capacity cross memory descriptors (ones capable of recording the + DMA descriptors). These cross memory descriptors are later mapped by the + server partition’s physical device drivers into the physical I/O + DMA address space of the physical I/O adapters using the kernel services, + that have been similarly extended to call the H_PUT_RTCE hcall(), based + upon the value of the LIOBN field reference by the cross memory + descriptor. At this point, the server partition’s VSCSI device + driver delivers what appears to be a SCSI request to be decoded and + routed through the server partition’s file sub-system for + processing. When the request completes, the server partition’s + VSCSI device driver is called by the file sub-system and it packages the + summary status along with the request correlator into a response message + that it sends to the client partition using the H_SEND_CRQ hcall(), then + recycles the resources recorded in the I/O request control block, and the + block itself. + The LIOBN value in the second window pane of the server + partition’s + “ibm,my-dma-window” property is intended + to be an indirect reference to the RTCE table of the client partition. + If, for some reason, the physical location of the client + partition’s RTCE table changes or it becomes invalid, this level of + indirection allows the hypervisor to determine the current target without + changing the LIOBN number as seen by the server partition. The H_PUT_TCE + and H_PUT_RTCE hcall()s do not map server partition memory into the + second window pane; the second window pane is only available for use by + server partition via the Logical RDMA services to reference memory mapped + into it by the client partition’s IOA. + This architecture does not specify the payload format of the + requests or responses. However, the architectural intent is supplied in + the following tables for reference. +   + + General Form of Reliable CRQ Element + + + + + + + + + + Byte Offset + + + + + Field Name + + + + + Subfield Name + + + + + Description + + + + + + + + 0 + + + Header + + +   + + + Contains Element Valid Bit plus Event Type Encodings (see + ). + + + + + 1 + + + Payload + + + Format/Transport Event Code + + + For Valid Command Response Entries, see + . For Transport Event + Codes see + . + + + + + 2-15 + + +   + + + Format Dependent. + + + + +
+   + + Example Reliable CRQ Entry Format Byte Definitions for VSCSI + + + + + + + + Format Byte Value + + + + + Definition + + + + + + + + 0x0 + + + Unused + + + + + 0x1 + + + VSCSI Requests + + + + + 0x2 + + + VSCSI Responses + + + + + 0x03 - 0xFE + + + Reserved + + + + + 0xFF + + + Reserved for Expansion + + + + +
+   + + Example VSCSI Command Queue Element + + + + + + + + + Byte Offset + + + + + Field Value + + + + + Description + + + + + + + + 0 + + + 0x80 + + + Valid Header + + + + + 1 + + + 0x01 + + + VSCSI Request Format + + + + + 2-3 + + + NA + + + Reserved + + + + + 4-7 + + +   + + + Length of the request block to be transferred + + + + + 8-15 + + +   + + + I/O address of beginning of request + + + + +
+   + + Example VSCSI Response Queue Element + + + + + + + + + Byte Offset + + + + + Field Value + + + + + Description + + + + + + + + 0 + + + 0x80 + + + Valid Header + + + + + 1 + + + 0x02 + + + VSCSI Response Format + + + + + 2-3 + + + NA + + + Reserved + + + + + 4-7 + + +   + + + Summary Status + + + + + 8-15 + + +   + + + 8 byte command correlator + + + + +
+ See also + . +
+ +
+ Virtual SCSI Requirements + This normative section provides the general requirements for the + support of VSCSI. + + + + R1--1. + + + For the VSCSI option: The platform must implement the + Reliable Command/Response Transport option as defined in + . + + + + + R1--2. + + + For the VSCSI option: The platform must implement the + Logical Remote DMA option as defined in + . + In addition to the firmware primitives, and the structures they + define, the partition’s OS needs to know specific information + regarding the configuration of the virtual IOA’s that it has been + assigned so that it can load and configure the correct device driver + code. This information is provided by the OF device tree node associated + with the virtual IOA (see + and + ). + + + + +
+ Client Partition Virtual SCSI Device Tree Node + Client partition VSCSI device tree nodes have associated packages + such as disk-label, deblocker, iso-13346-files and iso-9660-files as well + as children nodes such as block and byte as appropriate to the specific + virtual IOA configuration as would the node for a physical IOA of type + scsi-3. + + + + R1--1. + + + For the VSCSI option: The platform’s OF device + tree for client partitions must include as a child of the + /vdevice node, a node of name “v-scsi” as + the parent of a sub-tree representing the virtual IOAs assigned to the + partition. + + + + + R1--2. + + + For the VSCSI option: The platform’s + v-scsi OF node must contain properties as defined in + (other standard I/O adapter + properties are permissible as appropriate). +   + + Properties of the VSCSI Node in the Client + Partition + + + + + + + + + Property Name + + + + + Required? + + + + + Definition + + + + + + + + + “name” + + + + Y + + + Standard property name per + , + specifying the virtual device name, the + value shall be + “v-scsi”. + + + + + + “device_type” + + + + Y + + + Standard property name per + , + specifying the virtual device type, the + value shall be + + “vscsi”. + + + + + + “model” + + + + NA + + + Property not present. + + + + + + “compatible” + + + + Y + + + Standard property name per + , + specifying the programming models that are + compatible with this virtual IOA, the value shall include + “IBM,v-scsi”. + “IBM,v-scsi-2” precedes + “IBM,vsci” if it is included in + the value of this property. + + + + + + “used-by-rtas” + + + + See Definition Column + + + Present if appropriate. + + + + + + “ibm,loc-code” + + + + Y + + + Property name specifying the unique and persistent + location code associated with this virtual IOA presented as an + encoded array as with + encode-string. The value shall be of the + form specified in + . + + + + + + “reg” + + + + Y + + + Standard property name per + , + specifying the register addresses, used as + the unit address (unit ID), associated with this virtual IOA + presented as an encoded array as with + encode-phys of length + “#address-cells” value shall be + 0xwhatever (virtual + “reg” property used for unit + address no actual locations used, therefore, the size field has + zero cells (does not exist) as determined by the value of the + “#size-cells” property). + + + + + + “ibm,my-dma-window” + + + + Y + + + Property name specifying the DMA window associated with + this virtual IOA presented as an encoded array of three values + (LIOBN, phys, size) encoded as with + encode-int, + encode-phys, and + encode-int. + + + + + + “interrupts” + + + + Y + + + Standard property name specifying the interrupt source + number and sense code associated with this virtual IOA + presented as an encoded array of two cells encoded as with + encode-int with the first cell containing + the interrupt source number, and the second cell containing the + sense code 0 indicating positive edge triggered. The interrupt + source number being the value returned by the H_XIRR or H_IPOLL + hcall(). + + + + + + “ibm,my-drc-index” + + + + For DR + + + Present if the platform implements DR for this + node. + + + + + + “ibm,#dma-size-cells” + + + + See Definition Column + + + Property name, to define the package’s dma address + size format. The property value specifies the number of cells + that are used to encode the size field of dma-window + properties. This property is present when the dma address size + format cannot be derived using the method described in the + definition for the + “ibm,#dma-size-cells” property + in + . + + + + + + “ibm,#dma-address-cells” + + + + See Definition Column + + + Property name, to define the package’s dma address + format. The property value specifies the number of cells that + are used to encode the physical address field of dma-window + properties. This property is present when the dma address + format cannot be derived using the method described in the + definition for the + “ibm,#dma-address-cells” property in + . + + + + +
+ + + + + R1--3. + + + For the VSCSI option: The platform’s + v-scsi node must have as children the appropriate + block (disk) and byte + (tape) nodes. + + + +
+ +
+ Server Partition Virtual SCSI Device Tree Node + Server partition VSCSI IOA nodes have no children nodes. + + + + R1--1. + + + For the VSCSI option: The platform’s OF device + tree for server partitions must include as a child of the + /vdevice node, a node of name + “v-scsi-host” as the parent of a sub-tree + representing the virtual IOAs assigned to the partition. + + + + + R1--2. + + + For the VSCSI option: The platform’s + v-scsi-host node must contain properties as defined + in + (other standard I/O adapter + properties are permissible as appropriate). + + + + + + Properties of the VSCSI Node in the Server + Partition + + + + + + + + + Property Name + + + + + Required? + + + + + Definition + + + + + + + + + “name” + + + + Y + + + Standard property name per + , + specifying the virtual device name, the + value shall be + “v-scsi-host”. + + + + + + “device_type” + + + + Y + + + Standard property name per + , + specifying the virtual device type, the + value shall be + “v-scsi-host”. + + + + + + “model” + + + + NA + + + Property not present. + + + + + + “compatible” + + + + Y + + + Standard property name per + , + specifying the programming models that are + compatible with this virtual IOA, the value shall include + “IBM,v-scsi-host”. + “IBM,v-scsi-host-2” precedes + “IBM,vsci-host” if it is + included in the value of this property. + + + + + + + “used-by-rtas” + + + + See Definition Column + + + Present if appropriate. + + + + + + “ibm,loc-code” + + + + Y + + + Property name specifying the unique and persistent + location code associated with this virtual IOA presented as an + encoded array as with + encode-string. The value shall be of the + form + . + + + + + + “reg” + + + + Y + + + Standard property name per + , + specifying the register addresses, used as + the unit address (unit ID), associated with this virtual IOA + presented as an encoded array as with + encode-phys of length + “#address-cells” value shall be + 0xwhatever (virtual + “reg” property used for unit + address no actual locations used, therefore, the size field has + zero cells (does not exist) as determined by the value of the + “#size-cells” property). + + + + + + “ibm,my-dma-window” + + + + Y + + + Property name specifying the DMA window associated with + this virtual IOA presented as an encoded array of two sets (two + window panes) of three values (LIOBN, phys, size) encoded as + with + encode-int, + encode-phys, and + encode-int. Of these two triples, the + first describes the window pane used to map server partition + memory, the second is the window pane through which the client + partition maps its memory that it makes available to the server + partition. (Note the mapping between the LIOBN in the second + window pane of a server virtual IOA’s + “ibm,my-dma-window” property + and the corresponding client IOA’s RTCE table is made + when the CRQ successfully completes registration. See + for more information + on window panes.) + + + + + + “interrupts” + + + + Y + + + Standard property name specifying the interrupt source + number and sense code associated with this virtual IOA + presented as an encoded array of two cells encoded as with + encode-int with the first cell containing + the interrupt source number, and the second cell containing the + sense code 0 indicating positive edge triggered. The interrupt + source number being the value returned by the H_XIRR or H_IPOLL + hcall() + + + + + + “ibm,my-drc-index” + + + + For DR + + + Present if the platform implements DR for this + node. + + + + + + “ibm,vserver” + + + + Y + + + Property name specifying that this is a virtual server + node. + + + + + + “ibm,#dma-size-cells” + + + + See Definition Column + + + Property name, to define the package’s dma address + size format. The property value specifies the number of cells + that are used to encode the size field of dma-window + properties. This property is present when the dma address size + format cannot be derived using the method described in the + definition for the + “ibm,#dma-size-cells” property + in + . + + + + + + “ibm,#dma-address-cells” + + + + See Definition Column + + + Property name, to define the package’s dma address + format. The property value specifies the number of cells that + are used to encode the physical address field of dma-window + properties. This property is present when the dma address + format cannot be derived using the method described in the + definition for the + “ibm,#dma-address-cells” property in + . + + + + +
+   +
+
+
+ +
+ Virtual Terminal (Vterm) + This section defines the Virtual Terminal (Vterm) options (Client + Vterm option and Server Vterm option). Vterm IOAs are of the hypervisor + simulated class of VIO. See also + . + +
+ Vterm General + This section contains an informative outline of the architectural + intent of the use of Vterm support. + The architectural metaphor for the Vterm IOA is that of an Async + IOA. The connection at the other end of the Async “cable” may + be another Vterm IOA in a server partition, the hypervisor, or the + HMC. + A partition’s device tree contains one or more nodes + notifying the partition that it has been assigned one or more Vterm + client adapters (each LoPAR partition has at least one). The + node’s + “type” and + “compatible” properties notify the + partition that the virtual adapter is a Vterm client adapter. The + unit address of the node is used by the partition to + map the virtual device(s) to the OS’s corresponding logical + representations. The node’s + “interrupts” property, if it exists, + specifies the interrupt source number that has been assigned to the + client Vterm IOA for receive data. The partition, uses the + H_GET_TERM_CHAR and H_PUT_TERM_CHAR hcall()s to receive data from and + send data to the client Vterm IOA. If the node contains the + “interrupts” property, the partition may + optionally use the + ibm,int-on, + ibm,int-off, + ibm,set-xive, ibm,get-xive RTAS calls, and the + H_VIO_SIGNAL hcall() to manage the client Vterm IOA interrupt. + A partition’s device tree may also contain one or more + node(s) notifying the partition that it is requested to supply server + Vterm IOA services for one or more client Vterm IOAs. The node’s + “type” and + “compatible” properties notify the + partition that the virtual adapter is a server Vterm IOA. The unit + address (Unit ID) of the node is used by the partition to map + the virtual device(s) to the OS’s corresponding logical + representations. The node’s + “interrupts” property specifies the + interrupt source number that has been assigned to the server Vterm IOA + for receive data. The partition uses the H_VTERM_PARTNER_INFO hcall() to + find out which unit address(es) in which partition(s) to which it is + allowed to attach (that is, to which client Vterm IOAs it is allowed to + attach). The partition then uses the H_REGISTER_VTERM to setup the + connection between a server and a client Vterm IOAs, and uses the + H_GET_TERM_CHAR and H_PUT_TERM_CHAR hcall()s to receive data from and + send data to the server Vterm IOA. In addition, the partition may + optionally use the + ibm,int-on, + ibm,int-off, + ibm,set-xive, ibm,get-xive RTAS calls, and the + H_VIO_SIGNAL hcall() to manage the server Vterm IOA interrupt. + + shows a comparison between the + client and server versions of Vterm. +   + + Client Vterm versus Server Vterm Comparison + + + + + + + + + Client + + + + + Server + + + + + + + + The following hcall()s apply: + H_PUT_TERM_CHAR + H_GET_TERM_CHAR + H_VIO_SIGNAL (optional use with Client) + + + + + N/A + + + The following hcall()s are valid: + H_VTERM_PARTNER_INFO + H_REGISTER_VTERM + H_FREE_VTERM + + + + + + vty node + + + + vty-server node + + + + + The + “reg” property or the + vty node(s) + enumerates the valid client Vterm IOA unit + address(es) + + + The + “reg” property or the + vty-server node(s) enumerates the valid server Vterm IOA unit + address(es) + H_VTERM_PARTNER_INFO is used to getvalid client Vterm IOA partition ID(s) and corresponding + unit address(es) to which the server Vterm IOA is allowed to + connect + + + + + + “interrupts” property + optional: + Platform may or may not provide + If provided, Vterm driver may or may not use + + + + “interrupts” property + required: + Platform must provide + If provided, Vterm driver may or may not use + + + + +
+
+ +
+ Vterm Requirements + This normative section provides the general requirements for the + support of Vterm. + + + + R1--1. + + + For the LPAR option: + the Client Vterm option must be implemented. + + + + +
+ Character Put and Get hcall()s + The following hcall()s are used to send data to and get data from + both the client and sever Vterm IOAs. + +
+ H_GET_TERM_CHAR + + + + Syntax: + + + + + + + Parameters: + n termno: The unit address of the Vterm IOA, from the + “reg” property of the Vterm IOA. + + + + Semantics: + n Hypervisor checks the termno parameter for validity against the + Vterm IOA unit addresses assigned to the partition, else return + H_Parameter. + n Hypervisor returns H_Hardware if it detects that the virtual + console terminal physical connection is not working. + n Hypervisor returns H_Closed if it detects that the virtual + console associated with the termno parameter is not open (in the case of + connection to a server Vterm IOA, this means that the server code has not + made the connection to this specific client Vterm IOA). + n Hypervisor returns H_Success in all other cases, returning + maximum number of characters available in the partition’s virtual + console terminal input buffer (up to 16) -- a len value of 0 indicates + that the input buffer is empty. + n Upon return with H_Success register R4 contains the number of + bytes (if any) returned in registers R5 and R6. + n Upon return with H_Success the return character string starts in + the high order byte of register R5 and proceeds toward the low order byte + in register R6 for the number of characters specified in R4. The contents + of all other byte locations of registers R5 and R6 are undefined. + +
+ +
+ H_PUT_TERM_CHAR + + + + Syntax: + + + + + + + Parameters: + n termno: The unit address of the Vterm IOA, from the + “reg” property of the Vterm IOA. + n len: The length of the string to transmit through the virtual + terminal port. Valid values are in the range of 0-16. + n char0_7 and char8_15: The string starts in the high order byte of + register R6 and proceeds toward the low order byte in register R7 + + + + Semantics: + n Hypervisor checks the termno parameter for validity against the + Vterm IOA unit addresses assigned to the partition, else return + H_Parameter. + n Hypervisor returns H_Hardware if it detects that the virtual + console terminal physical connection is not working. + n Hypervisor returns H_Closed if it detects that the virtual + console session is not open (in the case of connection to a server Vterm + IOA, this means that the server code has not made the connection to this + specific client Vterm IOA). + n If the length parameter is outside of the values 0-16 the + hypervisor immediately returns H_Parameter with no other action. + n If the partition’s virtual console terminal buffer has room + for the entire string, the hypervisor queues the output string and + returns H_Success. + Note: There is always room for a zero length string (a + zero length write can be used to test the virtual console terminal + connection). + n If the buffer cannot hold the entire string, no data is enqueued + and the return code is H_Busy. + +
+
+ +
+ Interrupts + The interrupt source number is presented in the + “interrupts” property of the + Vterm node, when receive queue interrupts are + implemented for the Vterm. The + ibm,int-on, + ibm,int-off, + ibm,set-xive, ibm,get-xive RTAS calls, and + H_VIO_SIGNAL hcall() are used to manage the interrupt. + Interrupts and the + “interrupts” property are always + implemented for the server Vterm IOA, and may be implemented for the + client Vterm IOA. + The interrupt mechanism is edge-triggered and is capable of + presenting only one interrupt signal at a time from any given interrupt + source. Therefore, no additional interrupts from a given source are ever + signaled until the previous interrupt has been processed through to the + issuance of an H_EOI hcall(). Specifically, even if the interrupt mode is + enabled, the effect is to interrupt on an empty to non-empty transition + of the receiver queue or upon the closing of the connection between the + server and client. However, as with any asynchronous posting operation + race conditions are to be expected. That is, an enqueue can happen in a + window around the H_EOI hcall() so that the receiver should poll the + receive queue after an H_EOI using H_GET_TERM_CHAR after an H_EOI, to + prevent losing initiative. + + + + R1--1. + + + For the Server Vterm option: The platform must + implement the + “interrupts” property in all server + Vterm device tree nodes ( + vty-server), and must set the interrupt in that + property for the receive data interrupt for the IOA. + + + + + R1--2. + + + For the Client Vterm and Server Vterm options: When + implemented, the characteristics of the Vterm interrupts must be as + follows: + + + + All must be edge-triggered. + + + + The receive interrupt must be activated when the Vterm receive + queue goes from empty to non-empty. + + + + The receive interrupt must be activated when the Vterm + connection from the client to the server goes from open to closed. + + + + + +
+ +
+ Client Vterm Device Tree Node (vty) + All platforms that implement LPAR, also implement at least one + client Vterm IOA per partition. + + + + R1--1. + + + For the Client Vterm option: The H_GET_TERM_CHAR and + H_TERM_CHAR hcall()s must be implemented. + + + + + R1--2. + + + For the Client Vterm option: The platform’s OF + device tree must include as a child of the + /vdevice node, one or more nodes of type + “vty”; one for each client Vterm IOA. + + + + + R1--3. + + + For the Client Vterm option: The platform’s + vty OF node must contain properties as defined in + (other standard I/O adapter + properties are permissible as appropriate). +   + + Properties of the + <emphasis role="bold"><literal>vty</literal></emphasis> Node (Client Vterm IOA) + + + + + + + + + Property Name + + + + + Required? + + + + + Definition + + + + + + + + + “name” + + + + Y + + + Standard property name per + , + specifying the virtual device name. The + value shall be + “vty”. + + + + + + “device_type” + + + + Y + + + Standard property name per + , + specifying the virtual device type. The + value shall be + “serial”. + + + + + + “model” + + + + NA + + + Property not present. + + + + + + “compatible” + + + + Y + + + Standard property name per + , + specifying the programming models that are + compatible with this virtual IOA. The value shall include + “hvterm1” when the virtual IOA + will connect to a server with no special protocol, and shall + include + “hvterm-protocol” when the + virtual IOA will connect to a server that requires a protocol + to control modems or hardware control signals. + + + + + + “used-by-rtas” + + + + NA + + + Property not present. + + + + + + “ibm,loc-code” + + + + Y + + + Property name specifying the unique and persistent + location code associated with this virtual IOA presented as an + encoded array as with + encode-string. The value shall be of the + form specified in + . + + + + + + “reg” + + + + Y + + + Standard property name per + , + specifying the register addresses, used as + the unit address (unit ID), associated with this virtual IOA + presented as an encoded array as with + encode-phys of length + “#address-cells” value shall be + 0xwhatever (virtual + “reg” property used for unit + address no actual locations used, therefore, the size field has + zero cells (does not exist) as determined by the value of the + “#size-cells” property). + + + + + + “interrupts” + + + + See Definition Column + + + Standard property name specifying the interrupt source + number and sense code associated with this virtual IOA + presented as an encoded array of two cells encoded as with + encode-int with the first cell containing + the interrupt source number, and the second cell containing the + sense code 0 indicating positive edge triggered. The interrupt + source number being the value returned by the H_XIRR or H_IPOLL + hcall(). If provided, this property will present one interrupt; + the receive data interrupt. + + + + + + “ibm,my-drc-index” + + + + For DR + + + Present if the platform implements DR for this + node. + + + + +
+ + + + + R1--4. + + + For the Client Vterm option: If the compatible + property in the + vty node is + “hvterm-protocol”, then the protocol + that the client must use is defined in the document entitled + Protocol for Support of Physical Serial Port Using a Virtual + TTY Interface. + + + +
+ +
+ Server Vterm + Server Vterm IOAs allow a partition to serve a partner + partition’s client Vterm IOA. + +
+ Server Vterm Device Tree Node (vty-server) and Other + Requirements + + + + R1--1. + + + For the Server Vterm option: The H_GET_TERM_CHAR, + H_PUT_TERM_CHAR, H_VTERM_PARTNER_INFO, H_REGISTER_VTERM, and H_FREE_VTERM + hcall()s must be implemented. + + + + + R1--2. + + + For the Server Vterm option: The platform’s OF + device tree for partitions implementing server Vterm IOAs must include as + a child of the + /vdevice node, one or more nodes of type + “vty-server”; one for each server Vterm + IOA. + + + + + R1--3. + + + For the Server Vterm option: The platform’s + vty-server node must contain properties as defined in + + (other standard I/O adapter + properties are permissible as appropriate). + + + + + + Properties of the + <emphasis role="bold"><literal>vty-server</literal></emphasis> Node (Server Vterm IOA) + + + + + + + + + Property Name + + + + + Required? + + + + + Definition + + + + + + + + + “name” + + + + Y + + + Standard property name per + , + specifying the virtual device name. The + value shall be + “vty-server”. + + + + + + “device_type” + + + + Y + + + Standard property name per + , + specifying the virtual device type. The + value shall be + “serial-server”. + + + + + + “model” + + + + NA + + + Property not present. + + + + + + “compatible” + + + + Y + + + Standard property name per + , + specifying the programming models that are + compatible with this virtual IOA. The value shall include + “hvterm2”. + + + + + + “used-by-rtas” + + + + NA + + + Property not present. + + + + + + “ibm,loc-code” + + + + Y + + + Property name specifying the unique and persistent + location code associated with this virtual IOA presented as an + encoded array as with + encode-string. The value shall be of the + form + . + + + + + + “reg” + + + + Y + + + Standard property name per + , + specifying the register addresses, used as + the unit address (unit ID), associated with this virtual IOA + presented as an encoded array as with + encode-phys of length specified by + “#address-cells” value shall be + 0xwhatever (virtual + “reg” property used for unit + address no actual locations used, therefore, the size field has + zero cells (does not exist) as determined by the value of the + “#size-cells” property). + + + + + + “interrupts” + + + + Y + + + Standard property name specifying the interrupt source + number and sense code associated with this virtual IOA + presented as an encoded array of two cells encoded as with + encode-int with the first cell containing + the interrupt source number, and the second cell containing the + sense code 0 indicating positive edge triggered. The interrupt + source number being the value returned by the H_XIRR or H_IPOLL + hcall(). This property will present one interrupt; the receive + data interrupt. + + + + + + “ibm,my-drc-index” + + + + For DR + + + Present if the platform implements DR for this + node. + + + + + + “ibm,vserver” + + + + Y + + + Property name specifying that this is a virtual server + node. + + + + +
+
+ +
+ Server Vterm hcall()s + The following hcall()s are unique to the server Vterm IOA. + +
+ H_VTERM_PARTNER_INFO + This hcall is used to retrieve the list of Vterms to which the + specified server Vterm IOA is permitted to connect. The list is retrieved + by making repeated calls, and returns sets of triples: partner partition + ID, partner unit address, and partner location code. Passing in the + previously returned value will return the next value in the list of + allowed connections. Passing in a value of 0xFF...FF will return the + first value in the list. + + + Syntax: + + + + + + + Parameters: + + + + unit-address: Virtual IOA’s unit address, as specified in + the IOA’s device tree node. + + + + partner-partition-id: The partner partition ID of the last + partner partition ID and partner unit address pair returned. If a value + of 0xFF...FF is specified, the call returns the first item in the + list. + + + + partner-unit-addr: The partner unit address of the last partner + partition ID and partner unit address pair returned. If a value of + 0xFF...FF is specified, the call returns the first item in the + list. + + + + buffr-addr: The logical address of a single page in memory, + belonging to the calling partition, which is used to return the next + triple of information (partner partition ID, partner unit address, and + Converged Location Code). The calling partition cannot migrate the page + during the duration of the call, otherwise the call will fail. + Buffer format on return with H_Success: + + + + First eight bytes: Eight byte partner partition ID of the partner + partition ID and partner unit address pair from the list, or 0xFF...FF if + partner partition ID and partner unit address passed in the input + parameters was the last item in the list of valid connections. + + + + Second eight bytes: Eight byte partner unit address associated + with the partner partition ID (as returned in first 8 bytes of the + buffer), or 0xFF...FF if the partner partition ID and partner unit + address passed in the input parameters was the last item in the list of + valid connections. + + + + Beginning at the 17 byte in the buffer: NULL-terminated Converged + Location Code associated with the partner unit address and partner + partition ID (a returned in the first 16 bytes of the buffer), or just a + NULL string if the partner partition ID and partner unit address passed + in the input parameters was the last item in the list of valid + connections. + + + + + + Semantics: + + + + Validate that unit-address belongs to the partition and to a + server Vterm IOA, else H_Parameter. + + + + If partner-partition-id and partner-unit-addr together do not + match a valid partner partition ID and partner unit address pair in the + list of valid connections for this unit-address, then return + H_Parameter. + + + + If the 4 KB page associated with buffr-addr does not belong to + the calling partition, then return H_Parameter. + + + + If the buffer associated with buffr-addr does not begin on a 4 K + boundary, then return H_Parameter. + + + + If the calling partition attempts to migrate the buffer page + associated with buffr-addr during the duration of the + H_VTERM_PARTNER_INFO call, then return H_Parameter. + + + + If partner-partition-id is equal to 0xFF...FF, then select the + first item from the list of valid connections, format the buffer as + specified, above, for this item, and return H_Success. + + + + If partner-partition-id and partner-unit-addr together matches a + valid partner partition ID and partner unit address pair in the list of + valid connections, and if this is the last valid connection in the list, + then format the buffer as specified, above, with the partner partition ID + and partner unit address both set to 0xFF...FF, and the Converged + Location Code set to the NULL string, and return H_Success. + + + + If partner-partition-id and partner-unit-addr together matches a + valid partner partition ID and partner unit address pair in the list of + valid connections, then select the next item from the list of valid + connections, and format the buffer as specified, above, and return + H_Success. + + + +
+ +
+ H_REGISTER_VTERM + This hcall has the effect of “opening” the connection + to the client Vterm IOA in the specified partition ID and which has the + specified unit address. The architectural metaphor for this is the + connecting of the cable between two Async IOAs. The hcall fails if the + partition does not have the authority to connect to the requested + partition/unit address pair. The hcall() also fails if the specified + partition/unit address is already in use (for example, by another + partition or the HMC) + + + Syntax: + + + + + + + Parameters: + + + + unit-address: The server Virtual IOA’s unit address, as + specified in the IOA’s device tree node. + + + + partner-partition-id: The partition ID of the partition ID and + unit address pair to which to be connected. + + + + partner-unit-addr: The unit address of the partition ID and unit + address pair to which to be connected. + + + + + + Semantics: + + + + Validate that unit-address belongs to the partition and to a + server Vterm IOA and that there does not exist a valid connection between + this server Vterm IOA and a partner, else H_Parameter. + + + + If partner-partition-id and partner-unit-addr together do not + match a valid partition ID and unit address pair in the list of valid + connections for this unit-address, then return H_Parameter, + n Else make connection between the server Vterm IOA specified by + unit-address and the client Vterm IOA specified by the + partner-partition-id and partner-unit-addr pair, allowing future + H_PUT_TERM_CHAR and H_GET_TERM_CHAR operations to flow between the two + Vterm IOAs, and return H_Success. + + + + Software Implementation Note: An H_Parameter will be + returned to the H_REGISTER_VTERM if a DLPAR operation has been performed + which changes the list of possible server to client Vterm connections. + After a DLPAR operation which affects a partition’s server Vterm + IOA connection list, a call to H_VTERM_PARTNER_INFO is needed to get the + current list of possible connections. + +
+ +
+ H_FREE_VTERM + This hcall has the effect of “closing” the connection + to the partition/unit address pair. The architectural metaphor for this + is the removal of the cable between two Async IOAs. After closing, the + partner partition’s server Vterm IOA would now be available for + serving by another partner (for example, another partition or the + HMC). + + + Syntax: + + + + + + + Parameters: + + + + unit-address: Virtual IOA’s unit address, as specified in + the IOA’s device tree node. + + + + + + Semantics: + + + + Validate that the unit address belongs to the partition and to a + server Vterm IOA and that there exists a valid connection between this + server Vterm IOA and a partner, else H_Parameter. + + + + Break the connection between the server Vterm IOA specified by + the unit address and the client Vterm IOA, preventing further + H_PUT_TERM_CHAR and H_GET_TERM_CHAR operations between the two Vterm IOAs + (until a future successful H_REGISTER_VTERM operation), and return + H_Success. + + + Implementation Note: If the hypervisor returns an + H_Busy, H_LongBusyOrder1mSec, or H_LongBusyOrder10mSec, software must + call H_FREE_VTERM again with the same parameters. Software may choose to + treat H_LongBusyOrder1mSec and H_LongBusyOrder10mSec the same as H_Busy. + The hypervisor, prior to returning H_Busy, H_LongBusyOrder1mSec, or + H_LongBusyOrder10mSec, will have placed the virtual adapter in a state + that will cause it to not accept any new work nor surface any new virtual + interrupts. +   + +
+
+
+
+
+ +
+ Virtual Fibre Channel (VFC) using NPIV + N_Port ID Virtualization (NPIV) is part of the Fibre Channel (FC) + standards. NPIV allows multiple World Wide Port Names (WWPNs) to be mapped + to a single physical port of a FC adapter. This section defines a Virtual + Fibre Channel (VFC) interface to a server partition interfacing to a + physical NPIV adapter that allows multiple partitions to share a physical + port using different WWPNs. The implementation support is provided by code + running in a server partition that uses the mechanisms of the Reliable + Command/Response Transport and Logical Remote DMA of the Synchronous VIO + Infrastructure to service I/O requests for code running in a client + partition. The client partition appears to enjoy the services of its own FC + adapter (see + ) with a WWPN visible to the FC + fabric. The terms server and client partitions refer to platform partitions + that are respectively servers and clients of requests, usually I/O + operations, using the physical I/O adapters (IOAs) that are assigned to the + server partition. This allows a platform to have more client partitions + than it may have physical I/O adapters because the client partitions share + I/O adapters via the server partition. + The VFC model makes use of Remote DMA which is built upon the + architecture specified in the following sections: + + + + + + + + + + + + + + + +
+ VFC and NPIV General + This section contains an informative outline of the architectural + intent of the use of VFC and NIPV, and it assumes the user is familiar + with + concerning VSCSI architecture + and the with the FC standards. Other implementations of the server and + client partition code, consistent with this architecture, are possible + and may be preferable. + The client partition provides the virtual equivalent of a single + port FC adapter via each VFC client IOA. The platform, through the + partition definition, provides means for defining the set of virtual + IOA’s owned by each partition and their respective location codes. + The platform also provides, through partition definition, instructions to + connect each client partition’s VFC client IOA to a specific server + partition’s VFC server IOA. The mechanism for specifying this + partition definition is beyond the scope of this architecture. The human + readable handle associated with the partition definition of virtual IOAs + and their associated interconnection and resource configuration is the + virtual location code. The OF unit address (Unit ID) remains the invariant handle upon which the + OS builds its “physical to logical” configuration. The + platform also provides a method to assign unique WWPNs for each VFC + client adapter. The port names are used by a SAN administrator to grant + access to storage to a client partition. The mechanism for allocating + port names is beyond the scope of this architecture. + The client partition’s device tree contains one or more nodes + notifying the partition that it has been assigned one or more virtual + adapters. The node’s + “type” and + “compatible” properties notify the + partition that the virtual adapter is a VFC adapter. The + unit address of the node is used by the client + partition to map the virtual device(s) to the OS’s corresponding + logical representations. The + “ibm,my-dma-window” property communicates + the size of the RTCE table window panes that the hypervisor has + allocated. The node also specifies the interrupt source number that has + been assigned to the Reliable Command/Response Transport connection and + the RTCE range that the client partition device driver may use to map its + memory for access by the server partition via Logical Remote DMA. The + client partition also reads it's WWPNs from the device tree. Two WWPNs + are presented to the client in the properties + “ibm,port-wwn-1”, and + “ibm,port-wwn-2”, and the server tells + the client, through a CRQ protocol exchange, which one of the two to use. + The client partition, uses the four hcall()s associated with the Reliable + Command/Response Transport facility to register and deregister its CRQ, + manage notification of responses, and send command requests to the server + partition. + The server partition’s device tree contains one or more + node(s) notifying the partition that it is requested to supply VFC + services for one or more client partitions. The unit address ( + Unit ID) of the node is used by the server partition + to map to the local logical devices that are represented by this VFC + device. The node also specifies the interrupt source number that has been + assigned to the Reliable Command/Response Transport connection and the + RTCE range that the server partition device driver may use for its copy + Logical Remote DMA. The server partition uses the four hcall()s + associated with the Reliable Command/Response Transport facility to + register and deregister its Command request queue, manage notification of + new requests, and send responses back to the client partition. In + addition, the server partition uses the hcall()s of the Logical Remote + DMA facility to manage the movement of commands and data associated with + the client requests. + The client partition, upon noting the device tree entry for the + virtual adapter, loads the device driver associated with the value of the + + “compatible” property. The device driver, + when configured and opened, allocates memory for its CRQ (an array, large + enough for all possible responses, of 16 byte elements), pins the queue + and maps it into the I/O space of the RTCE window specified in the + “ibm,my-dma-window” property using the + standard kernel mapping services that subsequently use the H_PUT_TCE + hcall(). The queue is then registered using the H_REG_CRQ hcall(). Next, + I/O request control blocks (within which the I/O requests commands are + built) are allocated, pinned, and mapped into I/O address space. Finally, + the device driver registers to receive control when the interrupt source + specified in the virtual IOA’s device tree node signals. + Once the CRQ is setup, the device driver queues an Initialization + Command/Response with the second byte of “Initialize” in + order to attempt to tell the hosting side that everything is setup on the + hosted side. The response to this send may be that the send has been + dropped or has successfully been sent. If successful, the sender should + expect back an Initialization Command/Response with a second byte of + “Initialization Complete,” at which time the communication + path can be deemed to be open. If dropped, then the sender waits for the + receipt of an Initialization Command/Response with a second byte of + “Initialize,” at which time an “Initialization + Complete” message is sent, and if that message is sent + successfully, then the communication path can be deemed to be + open. + When the VFC Adapter device driver receives an I/O request from one + of the FC device head drivers, it executes the following sequence. First + an I/O request control block is allocated. Then it builds the FC + Information Unit (FC IU) request within the control block, adds a + correlator field (to be returned in the subsequent response), I/O maps + any target memory buffers and places their DMA descriptors into the I/O + request control block. With the request constructed in the I/O request + control block, the driver constructs a DMA descriptor (Starting Offset, + and length) representing the FC IU within the I/O request control block. + It also constructs a DMA descriptor for the FC Response Unit. Lastly, the + driver passes the I/O request’s DMA descriptor to the server + partition using the H_SEND_CRQ hcall(). Provided that the H_SEND_CRQ + hcall() succeeds, the VFC Adapter device driver returns, waiting for the + response interrupt indicating that a response has been posted by the + server partition to the device driver’s response queue. The + response queue entry contains the summary status and request correlator. + From the request correlator, the device driver accesses the I/O request + control block, the summary status, and the FC Response Unit and + determines how to complete the processing of the I/O request. + Notice that the client partition only uses the Reliable + Command/Response Transport primitives; it does not use the Logical Remote + DMA primitives. Since the server partition’s RTCE tables are not + authorized for access by the client partition, any attempt by the client + partition to modify server partition memory would be prevented by the + hypervisor. RTCE table access is granted on a connection by connection + basis (client/server virtual device pair). If a client partition happens + to be serving some other logical device, then the partition is entitled + to use Logical Remote DMA for the virtual devices that is serving. + The server partition, upon noting the device tree entry for the + virtual adapter, loads the device driver associated with the value of the + + “compatible” property. The device driver, + when configured and opened, allocates memory for its request queue (an + array, large enough for all possible outstanding requests, of 16 byte + elements). The driver then pins the queue and maps it into I/O space, via + the kernel’s I/O mapping services that invoke the H_PUT_TCE + hcall(), using the first window pane specified in the + “ibm,my-dma-window” property. The queue + is then registered using the H_REG_CRQ hcall(). Next, I/O request control + blocks (within which the I/O request commands are built) are allocated, + pinned, and I/O mapped. Finally the device driver registers to receive + control when the interrupt source specified in the virtual IOA’s + device tree node signals. + Once the CRQ is setup, the device driver queues an Initialization + Command/Response with the second byte of “Initialize” in + order to attempt to tell the hosted side that everything is setup on the + hosting side. The response to this send may be that the send has been + dropped or has successfully been sent. If successful, the sender should + expect back an Initialization Command/Response with a second byte of + “Initialization Complete,” at which time the communication + path can be deemed to be open. If dropped, then the sender waits for the + receipt of an Initialization Command/Response with a second byte of + “Initialize,” at which time an “Initialization + Complete” message is sent, and if that message is sent + successfully, then the communication path can be deemed to be + open. + When the server partition’s device driver receives an I/O + request from its corresponding client partition’s VFC adapter + drivers, it is notified via the interrupt registered for above. The + server partition’s device driver selects an I/O request control + block for the requested operation. It then uses the DMA descriptor from + the request queue element to transfer the FC IU request from the client + partition’s I/O request control block to its own (allocated above), + using the H_COPY_RDMA hcall() through the second window pane specified in + the + “ibm,my-dma-window” property. The server + partition’s device driver then uses kernel services, that are + extended, to register the I/O request’s DMA descriptors into + extended capacity cross memory descriptors (ones capable of recording the + DMA descriptors). These cross memory descriptors are later mapped by the + server partition’s physical device drivers into the physical I/O + DMA address space of the physical I/O adapters using the kernel services, + that have been similarly extended to call the H_PUT_RTCE hcall(), based + upon the value of the LIOBN field reference by the cross memory + descriptor. At this point, the server partition’s VFC device driver + delivers what appears to be a FC IU request to be routed through the + server partition’s adapter driver. When the request completes, the + server partition’s VFC device driver is called through a registered + entry point and it packages the summary status along with the request + correlator into a response message that it sends to the client partition + using the H_SEND_CRQ hcall(), then recycles the resources recorded in the + I/O request control block, and the block itself. + The LIOBN value in the second window pane of the server + partition’s + “ibm,my-dma-window” property is intended + to be an indirect reference to the RTCE table of the client partition. + If, for some reason, the physical location of the client + partition’s RTCE table changes or it becomes invalid, this level of + indirection allows the hypervisor to determine the current target without + changing the LIOBN number as seen by the server partition. The H_PUT_TCE + and H_PUT_RTCE hcall()s do not map server partition memory into the + second window pane; the second window pane is only available for use by + server partition via the Logical RDMA services to reference memory mapped + into it by the client partition’s IOA. + This architecture does not specify the payload format of the + requests or responses. However, the architectural intent is supplied in + the following tables for reference. +   + + General Form of Reliable CRQ Element + + + + + + + + + + Byte Offset + + + + + Field Name + + + + + Subfield Name + + + + + Description + + + + + + + + 0 + + + Header + + +   + + + Contains Element Valid Bit plus Event Type Encodings (see + + ). + + + + + 1 + + + Payload + + + Format/Transport Event Code + + + For Valid Command Response Entries, see + . For Transport Event + Codes see + . + + + + + 2-15 + + +   + + + Format Dependent. + + + + +
+   + + Example Reliable CRQ Entry Format Byte Definitions + for VFC + + + + + + + + + Format Byte Value + + + + + Definition + + + + + + + + 0x0 + + + Unused + + + + + 0x01 + + + VFC Requests + + + + + 0x02 - 0x03 + + + Reserved + + + + + 0x04 + + + Management Datagram + + + + + 0x05 - 0xFE + + + Reserved + + + + + 0xFF + + + Reserved for Expansion + + + + +
+   + + Example VFC Command Queue Element + + + + + + + + + Byte Offset + + + + + Field Value + + + + + Description + + + + + + + + 0 + + + 0x80 + + + Valid Header + + + + + 1 + + + 0x01 + + + VFC Requests + + + + + 1 + + + 0x04 + + + Management Datagram + + + + + 2-3 + + + NA + + + Reserved + + + + + 4-7 + + +   + + + Length of the request block to be transferred + + + + + 8-15 + + +   + + + I/O address of beginning of request + + + + +
+   + + Example VFC Response Queue Element + + + + + + + + + Byte Offset + + + + + Field Value + + + + + Description + + + + + + + + 0 + + + 0x80 + + + Valid Header + + + + + 1 + + + 0x01 + + + VFC Response Format + + + + + 1 + + + 0x02 + + + Asynchronous Event + + + + + 1 + + + 0x04 + + + Management Datagram + + + + + 2-3 + + + NA + + + Reserved + + + + + 4-7 + + +   + + + Summary Status + + + + + 8-15 + + +   + + + 8 byte command correlator + + + + +
+
+ +
+ VFC and NPIV Requirements + This normative section provides the general requirements for the + support of VFC. + + + + R1--1. + + + For the VFC option: The platform must implement the + Reliable Command/Response Transport option as defined in + . + + + + + R1--2. + + + For the VFC option: The platform must implement the + Logical Remote DMA option as defined in + . + + + + + R1--3. + + + For the VFC option: The platform must allocate a WWPN + pair for each VFC client and must present the WWPNs to the VFC clients in + their OF device tree + . + In addition to the firmware primitives, and the structures they + define, the partition’s OS needs to know specific information + regarding the configuration of the virtual IOA’s that it has been + assigned so that it can load and configure the correct device driver + code. This information is provided by the OF device tree node associated + with the virtual IOA (see + and + ). + + + + +
+ Client Partition VFC Device Tree Node + Client partition VFC device tree nodes have associated packages + such as disk-label, deblocker, iso-13346-files and iso-9660-files as well + as children nodes such as block and byte as appropriate to the specific + virtual IOA configuration as would the node for a physical FC IOA. + + + + R1--1. + + + For the VFC option: The platform’s OF device + tree for client partitions must include as a child of the + /vdevice node, a node of name + “vfc-client” as the parent of a sub-tree + representing the virtual IOAs assigned to the partition. + + + + + R1--2. + + + For the VFC option: The platform’s + vfc-client OF node must contain properties as defined + in + (other standard I/O adapter + properties are permissible as appropriate). +   + + Properties of the VFC Node in the Client + Partition + + + + + + + + + Property Name + + + + + Required? + + + + + Definition + + + + + + + + + “name” + + + + Y + + + Standard property name per + , + specifying the virtual device name, the + value shall be + “vfc-client”. + + + + + + “device_type” + + + + Y + + + Standard property name per + , + specifying the virtual device type, the + value shall be + + “fcp”. + + + + + + “model” + + + + NA + + + Property not present. + + + + + + “compatible” + + + + Y + + + Standard property name per + , + specifying the programming models that are + compatible with this virtual IOA, the value shall include + “IBM,vfc-client”. + + + + + + “used-by-rtas” + + + + See Definition Column + + + Present if appropriate. + + + + + + “ibm,loc-code” + + + + Y + + + Property name specifying the unique and persistent + location code associated with this virtual IOA presented as an + encoded array as with + encode-string. The value shall be of the + form specified in + . + + + + + + “reg” + + + + Y + + + Standard property name per + , + specifying the register addresses, used as + the unit address (unit ID), associated with this virtual IOA + presented as an encoded array as with + encode-phys of length + “#address-cells” value shall be + 0xwhatever (virtual + “reg” property used for unit + address no actual locations used, therefore, the size field has + zero cells (does not exist) as determined by the value of the + “#size-cells” property). + + + + + + “ibm,my-dma-window” + + + + Y + + + Property name specifying the DMA window associated with + this virtual IOA presented as an encoded array of three values + (LIOBN, phys, size) encoded as with + encode-int, + encode-phys, and + encode-int. + + + + + + “interrupts” + + + + Y + + + Standard property name specifying the interrupt source + number and sense code associated with this virtual IOA + presented as an encoded array of two cells encoded as with + encode-int with the first cell containing + the interrupt source number, and the second cell containing the + sense code 0 indicating positive edge triggered. The interrupt + source number being the value returned by the H_XIRR or H_IPOLL + hcall(). + + + + + + “ibm,my-drc-index” + + + + For DR + + + Present if the platform implements DR for this + node. + + + + + + “ibm,#dma-size-cells” + + + + See Definition Column + + + Property name, to define the package’s dma address + size format. The property value specifies the number of cells + that are used to encode the size field of dma-window + properties. This property is present when the dma address size + format cannot be derived using the method described in the + definition for the + “ibm,#dma-size-cells” property + in + . + + + + + + “ibm,#dma-address-cells” + + + + See Definition Column + + + Property name, to define the package’s dma address + format. The property value specifies the number of cells that + are used to encode the physical address field of dma-window + properties. This property is present when the dma address + format cannot be derived using the method described in the + definition for the + “ibm,#dma-address-cells” property in + . + + + + + + “ibm,port-wwn-1” + + + + See Definition Column + + + Property that represents one of two WWPNs assigned to + this VFC client node. This property is a + prop-encoded-array each encoded with + encode-int. The array consists of the high + order 32 bits and low order 32 bits of the WWPN such that (32 + bits high | 32 bits low) is the 64 bit WWPN. The WWPN that the + client is to use ( + “ibm,port-wwn-1” or + “ibm,port-wwn-2”) is + communicated to the client by the server as part of the + client-server communications protocol. + + + + + + “ibm,port-wwn-2” + + + + See Definition Column + + + Property that represents one of two WWPNs assigned to + this VFC client node This property is a + prop-encoded-array each encoded with + encode-int. The array consists of the high + order 32 bits and low order 32 bits of the WWPN such that (32 + bits high | 32 bits low) is the 64 bit WWPN. The WWPN that the + client is to use ( + “ibm,port-wwn-1” or + “ibm,port-wwn-2”) is + communicated to the client by the server as part of the + client-server communications protocol. + + + + +
+ + + + + R1--3. + + + For the VFC option: The platform’s + vfc-client node must have as children the appropriate + block (disk) and byte (tape) nodes. + + + +
+ +
+ Server Partition VFC Device Tree Node + Server partition VFC IOA nodes have no children nodes. + + + + R1--1. + + + For the VFC option: The platform’s OF device + tree for server partitions must include as a child of the + /vdevice node, a node of name + “vfc-server” as the parent of a sub-tree + representing the virtual IOAs assigned to the partition. + + + + + R1--2. + + + For the VFC option: The platform’s + vfc-server node must contain properties as defined in + + (other standard I/O adapter + properties are permissible as appropriate). + + + + + + Properties of the VFC Node in the Server + Partition + + + + + + + + + Property Name + + + + + Required? + + + + + Definition + + + + + + + + + “name” + + + + Y + + + Standard property name per + , + specifying the virtual device name, the + value shall be + “vfc-server”. + + + + + + “device_type” + + + + Y + + + Standard property name per + , + specifying the virtual device type, the + value shall be + “fcp”. + + + + + + “model” + + + + NA + + + Property not present. + + + + + + “compatible” + + + + Y + + + Standard property name per + , + specifying the programming models that are + compatible with this virtual IOA, the value shall include + “IBM,vfc-server”. + + + + + + “used-by-rtas” + + + + See Definition Column + + + Present if appropriate. + + + + + + “ibm,loc-code” + + + + Y + + + Property name specifying the unique and persistent + location code associated with this virtual IOA presented as an + encoded array as with + encode-string. The value shall be of the + form + . + + + + + + “reg” + + + + Y + + + Standard property name per + , + specifying the register addresses, used as + the unit address (unit ID), associated with this virtual IOA + presented as an encoded array as with + encode-phys of length + “#address-cells” value shall be + 0xwhatever (virtual + “reg” property used for unit + address no actual locations used, therefore, the size field has + zero cells (does not exist) as determined by the value of the + “#size-cells” property). + + + + + + “ibm,my-dma-window” + + + + Y + + + Property name specifying the DMA window associated with + this virtual IOA presented as an encoded array of two sets (two + window panes) of three values (LIOBN, phys, size) encoded as + with + encode-int, + encode-phys, and + encode-int. Of these two triples, the + first describes the window pane used to map server partition + memory, the second is the window pane through which the client + partition maps its memory that it makes available to the server + partition. (Note the mapping between the LIOBN in the second + window pane of a server virtual IOA’s + “ibm,my-dma-window” property + and the corresponding client IOA’s RTCE table is made + when the CRQ successfully completes registration. See + for more information + on window panes.) + + + + + + “interrupts” + + + + Y + + + Standard property name specifying the interrupt source + number and sense code associated with this virtual IOA + presented as an encoded array of two cells encoded as with + encode-int with the first cell containing + the interrupt source number, and the second cell containing the + sense code 0 indicating positive edge triggered. The interrupt + source number being the value returned by the H_XIRR or H_IPOLL + hcall() + + + + + + “ibm,my-drc-index” + + + + For DR + + + Present if the platform implements DR for this + node. + + + + + + “ibm,vserver” + + + + Y + + + Property name specifying that this is a virtual server + node. + + + + + + “ibm,#dma-size-cells” + + + + See Definition Column + + + Property name, to define the package’s dma address + size format. The property value specifies the number of cells + that are used to encode the size field of dma-window + properties. This property is present when the dma address size + format cannot be derived using the method described in the + definition for the + “ibm,#dma-size-cells” property + in + . + + + + + + “ibm,#dma-address-cells” + + + + See Definition Column + + + Property name, to define the package’s dma address + format. The property value specifies the number of cells that + are used to encode the physical address field of dma-window + properties. This property is present when the dma address + format cannot be derived using the method described in the + definition for the + “ibm,#dma-address-cells” property in + . + + + + +
+   +
+
+
+ +
+ Virtual Network Interface Controller (VNIC) + This section defines a Virtual Network Interface Controller (VNIC) + interface to a server partition interfacing to a physical Network Interface + Controller (NIC) adapter that allows multiple partitions to share a + physical port. The implementation support is provided by code running in a + server partition that uses the mechanisms of the Synchronous VIO + Infrastructure (or equivalent thereof as seen by the client) to service I/O + requests for code running in a client partition + The server partition for VNIC is expected to be part of the + platform firmware and therefore an OS interface is not provided in this + architecture for the server side. However, the platform firmware is still + expected to be implemented by a partition, and hence the term + “server partition.” + . The client partition appears to enjoy the services of its own + NIC adapter. The terms server and client partitions refer to platform + partitions that are respectively servers and clients of requests, usually + I/O operations, using the physical NIC that is assigned to the server + partition. This allows a platform to have more client partitions than it + may have physical NICs because the client partitions share I/O adapters via + the server partition. + The VNIC model makes use of Remote DMA which is built upon the + architecture specified in the following sections: + + + + + + + + + + + + + + + + The use of Remote DMA has implications that the physical NIC be able + to do some of its own vitualization. For example, for an Ethernet adapter, + being able to route receive requests, via DMA to the appropriate client + partition, based on the addressing in the incoming packet. + +
+ VNIC General + This section contains an informative outline of the architectural + intent of the use of VNIC. Other implementations of the server and client + partition code, consistent with this architecture, are possible and may + be preferable. + The client partition provides the virtual equivalent of a single + port NIC adapter via each VNIC client IOA. The platform, through the + partition definition, provides means for defining the set of virtual + IOA’s owned by each partition and their respective location codes. + The platform also provides, through partition definition, instructions to + connect each client partition’s VNIC client IOA to a specific + server partition’s VNIC server IOA. The mechanism for specifying + this partition definition is beyond the scope of this architecture. The + human readable handle associated with the partition definition of virtual + IOAs and their associated interconnection and resource configuration is + the virtual location code. The OF unit address (unit ID) remains the + invariant handle upon which the OS builds its “physical to + logical” configuration. The platform also provides a method to + assign unique MAC addresses for each VNIC client adapter. The mechanism + for allocating port names is beyond the scope of this + architecture. + The client partition’s device tree contains one or more nodes + notifying the partition that it has been assigned one or more virtual + adapters. The node’s + “type” and + “compatible” properties notify the + partition that the virtual adapter is a VNIC. The unit address of the + node is used by the client partition to map the virtual device(s) to the + OS’s corresponding logical representations. The + “ibm,my-dma-window” property communicates + the size of the RTCE table window panes that the hypervisor has + allocated. The node also specifies the interrupt source number that has + been assigned to the Reliable Command/Response Transport connection and + the RTCE range that the client partition device driver may use to map its + memory for access by the server partition via Logical Remote DMA. The + client partition, uses the hcall()s associated with the Reliable + Command/Response Transport facility to register and deregister its CRQ, + manage notification of responses, and send command requests to the server + partition. The client partition uses the hcall()s associated with the + Subordinate CRQ Transport facility to register and deregister any + sub-CRQs necessary for the operations of the VNIC. + The client partition, upon noting the device tree entry for the + virtual adapter, loads the device driver associated with the value of the + + “compatible” property. The device driver, + when configured and opened, allocates memory for its CRQ (an array, large + enough for all possible responses, of 16 byte elements), pins the queue + and maps it into the I/O space of the RTCE window specified in the + “ibm,my-dma-window” property using the + standard kernel mapping services that subsequently use the H_PUT_TCE + hcall(). The queue is then registered using the H_REG_CRQ hcall(). Next, + I/O request control blocks (within which the I/O requests commands are + built) are allocated, pinned, and mapped into I/O address space. Finally, + the device driver registers to receive control when the interrupt source + specified in the virtual IOA’s device tree node signals. + Once the CRQ is setup, the device driver in the client queues an + Initialization Command/Response with the second byte of + “Initialize” in order to attempt to tell the hosting side + that everything is setup on the hosted side. The response to this send + may be that the send has been dropped or has successfully been sent. If + successful, the sender should expect back an Initialization + Command/Response with a second byte of “Initialization + Complete,” at which time the communication path can be deemed to be + open. If dropped, then the sender waits for the receipt of an + Initialization Command/Response with a second byte of + “Initialize,” at which time an “Initialization + Complete” message is sent, and if that message is sent + successfully, then the communication path can be deemed to be + open. + Once the CRQ connection is complete between the client and the + server, the client receives from the server the number of sub-CRQs that + can be supported on the client side. The client allocates memory for the + first sub-CRQ (an array, large enough for all possible responses, of 32 + byte elements), pins the queue and maps it into the I/O space of the RTCE + window specified in the + “ibm,my-dma-window” property using the + standard kernel mapping services that subsequently use the H_PUT_TCE + hcall(). The queue is then registered using the H_REG_SUB_CRQ hcall(). + This process continues until all desired sub-CRQs are registered or until + the H_REG_SUB_CRQ hcall() indicates that the resources allocated to the + client for sub-CRQs for the virtual IOA have already been allocated + (H_Resource returned). Interrupt numbers for the Sub-CRQs that have been + registered, are returned by the H_REG_SUB_CRQ hcall() (See + ). + Once all the CRQs and Sub-CRQs are setup, the communications + between the client and server device drivers may commence for purposes of + further setup operations, and then normal I/O requests, error + communications, etc. The protocol for this communications is beyond the + scope of this architecture. +
+ +
+ VNIC Requirements + This normative section provides the general requirements for the + support of VNIC. + + + + R1--1. + + + For the VNIC option: The platform must implement the + Reliable Command/Response Transport option as defined in + . + + + + + R1--2. + + + For the VNIC option: The platform must implement the + Subordinate CRQ Transport option as defined in + . + + + + + R1--3. + + + For the VNIC option: The platform must implement the + Logical Remote DMA option as defined in + . + + + + + R1--4. + + + For the VNIC option: The platform’s OF device + tree for client partitions must include as a child of the + /vdevice node, at least one node of name + “vnic”. + + + + + R1--5. + + + For the VNIC option: The platform’s + vnic OF node must contain properties as defined in + (other standard I/O adapter + properties are permissible as appropriate). + + + + + + Properties of the <emphasis role="bold"><literal>vnic</literal></emphasis> Node in the OF Device Tree + + + + + + + + + Property Name + + + + + Required? + + + + + Definition + + + + + + + + + “name” + + + + Y + + + Standard property name per + , specifying the + virtual device name, the value shall be + “vnic”. + + + + + + “device_type” + + + + Y + + + Standard property name per + , specifying the + virtual device type, the value shall be + “network”. + + + + + + “model” + + + + NA + + + Property not present. + + + + + + “compatible” + + + + Y + + + Standard property name per + , specifying the + programming models that are compatible with this virtual IOA, + the value shall include + “IBM,vnic”. + + + + + + “used-by-rtas” + + + + See definition column + + + Present if appropriate. + + + + + + “ibm,loc-code” + + + + Y + + + Property name specifying the unique and persistent + location code associated with this virtual IOA. + + + + + + “reg” + + + + Y + + + Standard property name per + , specifying the unit + address (unit ID) associated with this virtual IOA presented as + an encoded array as with + encode-phys of length + “#address-cells” value shall be + 0xwhatever (virtual + “reg” property used for unit + address no actual locations used, therefore, the size field has + zero cells (does not exist) as determined by the value of the + “#size-cells” property). + + + + + + “ibm,my-dma-window” + + + + Y + + + Property name specifying the DMA window associated with + this virtual IOA presented as an encoded array of three values + (LIOBN, phys, size) encoded as with + encode-int, + encode-phys, and + encode-int. + + + + + + “interrupts” + + + + Y + + + Standard property name specifying the interrupt source + number and sense code associated with this virtual IOA + presented as an encoded array of two cells encoded as with + encode-int with the first cell containing + the interrupt source number, and the second cell containing the + sense code 0 indicating positive edge triggered. The interrupt + source number being the value returned by the H_XIRR or H_IPOLL + hcall(). + + + + + + “ibm,my-drc-index” + + + + For DR + + + Present if the platform implements DR for this + node. + + + + + + “ibm,#dma-size-cells” + + + + See definition column + + + Property name, to define the package’s dma address + size format. The property value specifies the number of cells + that are used to encode the size field of dma-window + properties. This property is present when the dma address size + format cannot be derived using the method described in the + definition for the + “ibm,#dma-size-cells” property + in + . + + + + + + “ibm,#dma-address-cells” + + + + See definition column + + + Property name, to define the package’s dma address + format. The property value specifies the number of cells that + are used to encode the physical address field of dma-window + properties. This property is present when the dma address + format cannot be derived using the method described in the + definition for the + “ibm,#dma-address-cells” property in + . + + + + + + “local-mac-address” + + + + Y + + + Standard property name per + , specifying the + locally administered MAC addresses are denoted by having the + low order two bits of the high order byte being 0b10. + + + + + + “mac-address” + + + + Y + + + Standard property name per + , specifying the + initial MAC address (may be changed by a VNIC CRQ + command). + + + + + + “supported-network-types” + + + + Y + + + Standard property name as per + . + Reports possible types of “network” + the device can support. + + + + + + “chosen-network-type” + + + + Y + + + Standard property name as per + . + Reports the type of “network” this + device is supporting. + + + + + + “max-frame-size” + + + + Y + + + Standard property name per + , to indicate maximum + packet size. + + + + + + “address-bits” + + + + Y + + + Standard property name per + , to indicate network + address length. + + + + + “interrupt-ranges” + + + Y + + + Standard property name that defines the interrupt + number(s) and range(s) handled by this device. Subordinate CRQs + associated with this VNIC use interrupt numbers from these + ranges. + + + + +
+
+
+ diff --git a/Virtualization/ch_virtual_nic.xml b/Virtualization/ch_virtual_nic.xml new file mode 100644 index 0000000..86e0f65 --- /dev/null +++ b/Virtualization/ch_virtual_nic.xml @@ -0,0 +1,9890 @@ + + A Protocol for VNIC Communications + +
+ Introduction + The VNIC protocol defined in this chapter defines the protocol to be + used with VNIC virtual IOA, as defined in + . VNIC provides a mechanism which + minimizes the number of times data is copied within the memory of the + physical system. The virtual I/O model described herein allows for either + zero copy using the redirected DMA or single copy when the data is first + moved to the memory space of firmware before being DMAed to the client + partition. + This protocol is designed to fulfill the following + requirements: + + + + Fast, efficient transfer and reception of Ethernet frames + + + + Exploitation of adapter multiple transmit and receive queue + support. + + + + Partition mobility capable + + + + Promiscuous mode support + + + + Stateless TCP and IP checksum offload + + + + TCP large send offload + + + + Multiple interrupt source support + + + + Notification of physical Ethernet link state + + + + Physical Ethernet link state control if configured + + + + Statistics, trace, and dump support + + + + Extensible protocol for future functional additions + + +
+ +
+ VNIC Adapter + The intent of this protocol is to support the implementation, within + the client logical partition, of a VNIC adapter device driver (VNIC client) + which is functionally similar to a physical Ethernet adapter device driver. + The VNIC can send and receive Ethernet packets, add receive buffers to the + virtualized hardware, handle physical and logical link status, acquire + hardware statistics, and utilize advanced hardware features like checksum + offload. The VNIC interface also provides tracing, logging, and dumping + facilities. + It is the firm intent of this protocol that no changes be required in + any layer 3 or higher communication protocol (e.g. TCP, IP, etc.). + A partition may have multiple VNIC Adapters. +
+
+ Zero Copy DMA Models + Unlike the Interpartition Logical LAN option (See + ), the VNIC protocol allows for + the physical Ethernet adapter associated with the VNIC device to securely + target memory pages associated with a VNIC adapter for virtual I/O + operations. LoPAR defines two modes of LRDMA (See + ). + The use of Redirected RDMA is completely invisible to the VNIC + adapter, and has no impact on the VNIC protocol defined here. It is left + entirely to the discretion of the server firmware whether it first moves + data from a physical adapter into its own memory before moving (DMAing) the + data to the VNIC adapter, or whether the physical adapter sets up the I/O + request in such a way that the physical device DMAs directly to the memory + of the client adapter. The virtualizing firmware uses the RDMA mode that + best suits its needs for a given virtual I/O operation. +
+
+ Protocol Overview + + The CRQ and Sub-CRQ facilities as defined in + are used to send and receive VNIC + commands to system firmware. The different VNIC command types are defined + in + . + Throughout this document, boolean values assume 0 to be false, 1 to + be true. Unless otherwise specified, all lengths are expected to be given + in terms of bytes. Any setting or capability changed or enabled after a + successful H_REGISTER_CRQ will be cleared when H_FREE_CRQ is + performed. + The format of a VNIC command is shown in + . The Command Type field of the + VNIC command is defined in + . The Return Code for a a VNIC + command is always at offset 12 in the response, as shown in + . + All VNIC commands have VNIC command values from 0x0 to 0x7F. Each + response to a VNIC command has a VNIC command value that is equal to the + command with the 0x80 bit in the command turned on. + In the event firmware receives a command it doesn’t understand, + a response will be returned with an UnknownCommand return code set at + offset 12, and the VNIC command type set to the passed in command type with + the 0x80 bit turned on. + + + Format of the VNIC command + + + + + + + + + + + + + + + Byte Offset + + + 0 + + + 1 + + + 2 + + + 3 + + + 4 + + + 5 + + + 6 + + + 7 + + + + + + + 0x00 + + + 0x80 + + + Command Type + + + Command dependent + + + + + 0x08 + + + Command dependent + + + Return Code or Command Dependent + + + + +
+   + + VNIC Return Code + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + Architected Return Value + + + 0 + + + 1 + + + This field contains a value from + that contains the high + level return code for the operation. + + + + + Detailed Error Data + + + 1 + + + 3 + + + This field contains an unarchitected detailed error code + that can be used by firmware to further classify the error + returned in the architected return value. + + + + +
+   + + VNIC Command Types + + + + + + + + + + Command Type + + + Command value + + + Sent by + + + Description + + + Location + + + + + + + VERSION_EXCHANGE + + + 0x01 + + + VNIC Client + + + Used to inform firmware of level of protocol VNIC + supports + + + + + + + + + + VERSION_EXCHANGE_RSP + + + 0x81 + + + Firmware + + + Used to inform VNIC of level of protocol firmware + supports + + + + + + + + + + QUERY_CAPABILITY + + + 0x02 + + + VNIC Client + + + Query firmware for a specific VNIC capability + + + + + + + + + + QUERY_CAPABILITY_RSP + + + 0x82 + + + Firmware + + + Response for a QUERY_CAPABILITY + + + + + + + + + + REQUEST_CAPABILITY + + + 0x03 + + + VNIC Client + + + Request firmware to start using a specific capability + value + + + + + + + + + + REQUEST_CAPABILITY_RSP + + + 0x83 + + + Firmware + + + Response from firmware to a REQUEST_CAPABILITY + command + + + + + + + + + + LOGIN + + + 0x04 + + + VNIC Client + + + Used to exchange Sub-CRQ information with system firmware + in preparation for functional use of the virtualized + adapter + + + + + + + + + + LOGIN_RSP + + + 0x84 + + + Firmware + + + Response from firmware with firmware’s Sub-CRQ + information in preparation for functional use. + + + + + + + + + + QUERY_PHYS_PARMS + + + 0x05 + + + VNIC Client + + + Used by VNIC client to enquire about physical port + parameters such as line speed, duplex setting, etc. + + + + + + + + + + QUERY_PHYS_PARMS_RSP + + + 0x85 + + + Firmware + + + A response to the QUERY_PHYS_PARMS request containing the + requested information + + + + + + + + + + QUERY_PHYS_CAPABILITIES + + + 0x06 + + + VNIC Client + + + Used by VNIC client to enquire about physical port + capabilities such as line speed. + + + + + + + + + + QUERY_PHYS_CAPABILITIES_RSP + + + 0x86 + + + Firmware + + + A response to the QUERY_PHYS_CAPABILITIES request + containing the requested information. + + + + + + + + + + SET_PHYS_PARMS + + + 0x07 + + + VNIC Client + + + Used by the VNIC to set physical port parameters such as + line speed if allowed. + + + + + + + + + + SET_PHYS_PARMS_RSP + + + 0x87 + + + Firmware + + + Response indicating status of SET_PHYS_PARMS request + + + + + + + + + + ERROR_INDICATION + + + 0x08 + + + Firmware + + + Used to indicate to either side of an error + condition. + + + + + + + + + + REQUEST_ERROR_INFO + + + 0x09 + + + VNIC Client + + + Used to request detailed error data about a previous + asynchronous error condition + + + + + + + + + + REQUEST_ERROR_RSP + + + 0x89 + + + Firmware + + + Used to return detailed error data in response to a + request + + + + + + + + + + REQUEST_DUMP_SIZE + + + 0x0A + + + VNIC Client + + + Used to request an estimate of how much size a VNIC + collected debug dump will require. + + + + + + + + + + REQUEST_DUMP_SIZE_RSP + + + 0x8A + + + Firmware + + + Used to inform VNIC of the dump size estimate. + + + + + + + + + + REQUEST_DUMP + + + 0x0B + + + VNIC Client + + + Used to request firmware to perform an adapter & + firmware dump to assist in problem determination + + + + + + + + + + REQUEST_DUMP_RSP + + + 0x8B + + + Firmware + + + Used to inform VNIC Client when the requested dump has been + completed + + + + + + + + + + LOGICAL_LINK_STATE + + + 0x0C + + + VNIC Client + + + Used by VNIC Client to tell firmware to start and stop + packet reception + + + + + + + + + + LOGICAL_LINK_STATE_RSP + + + 0x8C + + + Firmware + + + Used to inform VNIC Client of the status of the LINK_STATE + request + + + + + + + + + + REQUEST_STATISTICS + + + 0x0D + + + VNIC Client + + + Used to retrieve standard network adapter statistics + (bytes/packet sent/rcvd, etc.) + + + + + + + + + + REQUEST_STATISTICS_RSP + + + 0x8D + + + Firmware + + + Used to inform VNIC Client when statistics were + successfully collected + + + + + + + + + + REQUEST_RAS_COMP_NUM + + + 0x0E + + + VNIC Client + + + Used by VNIC Client to retrieve the number of independent + firmware components that can have their RAS capabilities + controlled in firmware associated with the VNIC + + + + + + + + + + REQUEST_RAS_COMP_NUM_RSP + + + 0x8E + + + Firmware + + + Response to the REQUEST_RAS_COMP_NUM command. + + + + + + + + + + REQUEST_RAS_COMPS + + + 0x0F + + + VNIC Client + + + Used by VNIC Client to retrieve the list of component ids + that can have their RAS capabilities controlled in firmware for + this VNIC. + + + + + + + + + + REQUEST_RAS_COMPS_RSP + + + 0x8F + + + Firmware + + + Response to the REQUEST_RAS_COMPS_RSP. + + + + + + + + + + CONTROL_RAS + + + 0x10 + + + VNIC Client + + + Request firmware to modify RAS characteristics to allow for + easier problem determination. + + + + + + + + + + CONTROL_RAS_RSP + + + 0x90 + + + Firmware + + + Response to the CONTROL_RAS command. + + + + + + + + + + COLLECT_FW_TRACE + + + 0x11 + + + VNIC Client + + + This allows the VNIC Client to collect a trace for a + firmware component. + + + + + + + + + + COLLECT_FW_TRACE_RSP + + + 0x91 + + + Firmware + + + Inform VNIC Client the trace collection is complete + + + + + + + + + + LINK_STATE_INDICATION + + + 0x12 + + + Firmware + + + Inform VNIC Client of link state changes. + + + + + + + + + + CHANGE_MAC_ADDR + + + 0x13 + + + VNIC Client + + + Request system firmware to change the current VNIC MAC + address + + + + + + + + + + CHANGE_MAC_ADDR_RSP + + + 0x93 + + + Firmware + + + Inform VNIC Client of MAC address change request + status + + + + + + + + + + MULTICAST_CTRL + + + 0x14 + + + VNIC Client + + + Request system firmware to change current multicast MAC + address settings + + + + + + + + + + MULTICAST_CTRL_RSP + + + 0x94 + + + Firmware + + + Inform VNIC Client of multicast response + + + + + + + + + + GET_VPD_SIZE + + + 0x15 + + + VNIC Client + + + Query firmware for the size of VPD + + + + + + + + + + GET_VPD_SIZE_RSP + + + 0x95 + + + Firmware + + + Return the size of VPD to VNIC client + + + + + + + + + + GET_VPD + + + 0x16 + + + VNIC Client + + + Request system firmware to return VPD associated with + adapter. + + + + + + + + + + GET_VPD_RSP + + + 0x96 + + + Firmware + + + Response to GET_VPD. + + + + + + + + + + TUNE + + + 0x17 + + + VNIC Client + + + Pass debugging information to system firmware + + + + + + + + + + TUNE_RSP + + + 0x97 + + + Firmware + + + Response to TUNE command. + + + + + + + + + + QUERY_IP_OFFLOAD + + + 0x18 + + + VNIC Client + + + Request details about TCP, UDP, and IP offload + capabilities + + + + + + + + + + QUERY_IP_OFFLOAD_RSP + + + 0x98 + + + Firmware + + + Response to QUERY_IP_OFFLOAD command. + + + + + + + + + + CONTROL_IP_OFFLOAD + + + 0x19 + + + VNIC Client + + + Enable and disable TCP, UDP, and IP offload + capabilities + + + + + + + + + + CONTROL_IP_OFFLOAD_RSP + + + 0x99 + + + Firmware + + + Response to CONTROL_IP_OFFLOAD command. + + + + + + + + + + ACL_CHANGE_INDICATION + + + 0x1A + + + Firmware + + + Inform VNIC client of dynamic changes to access + controls + + + + + + + + + + ACL_QUERY + + + 0x1B + + + VNIC Client + + + Request information about access control limitations in + place for this VNIC. + + + + + + + + + + ACL_QUERY_RSP + + + 0x9B + + + Firmware + + + Response to ACL_QUERY command. + + + + + + + + + + REQUEST_DEBUG_STATS + + + 0x1C + + + VNIC Client + + + Request unarchitected statistics block used for debugging + firmware problems. + + + + + + + + + + REQUEST_DEBUG_STATS_RSP + + + 0x9C + + + Firmware + + + Response to REQUEST_DEBUG_STATS command. + + + + + + + + + +
+   + + VNIC Architected Return Values + + + + + + + + + + Return Code + + + + + Value + + + + + Definition + + + + + + + + Success + + + 0 + + + The requested operation completed successfully. + + + + + PartialSuccess + + + 1 + + + The requested operation completed partially successful. The + parameters were valid, but not all resources could be obtained to + completely satisfy the command. Check the specific function + definition for details. + + + + + Permission + + + 2 + + + The request called for permissions not available. + + + + + NoMemory + + + 3 + + + The request failed due to insufficient memory. + + + + + Parameter + + + 4 + + + One or more parameters were in error in the request. + + + + + UnknownCommand + + + 5 + + + The specific VNIC command is unknown. + + + + + Aborted + + + 6 + + + The command was aborted by some other action. + + + + + InvalidState + + + 7 + + + The requested command is invalid at this time. + + + + + InvalidIOBA + + + 8 + + + An I/O bus address passed as a parameter was + invalid. + + + + + InvalidLength + + + 9 + + + A length passed as a parameter was invalid. + + + + + UnsupportedOption + + + 10 + + + A reserved value or option was used on an existing command + that system firmware does not support. + + + + + Reserved + + + 11-255 + + + These return codes are reserved. + + + + +
+
+
+ Typical VNIC Protocol Flows +
+ Boot Flow + This section gives an overview of the typical VNIC startup + sequence. + + + + The operating system discovers a VNIC device in the device + tree. + + + + The operating system instantiates the VNIC client device driver, + allocates a buffer for the VNIC CRQ, which is then TCE-mapped using the + VNIC’s TCE table. Since the VNIC protocol is a command/response + protocol, the VNIC client should allocate a CRQ buffer big enough to + handle a response for every command it wishes to have outstanding + concurrently with firmware with an allowance for unsolicited asynchronous + error and link state change CRQ events. + + + + VNIC client calls H_REG_CRQ specifying the unit address and IOBA + of the CRQ page(s), and waits for either H_Success or an INITIALIZATION + message as defined in + . + + + + VNIC client sends either an INITIALIZATION_COMPLETE or an + INITIALIZATION message to firmware using H_SEND_CRQ, as defined in + . + + + + Once the INITIALIZATION and INITIALIZATION_COMPLETE messages + have been exchanged, the VNIC client sends a VERSION_EXCHANGE using + H_SEND_CRQ, specifying the latest version of the VNIC protocol supported + by the VNIC client. + + + + Firmware responds with a VERSION_EXCHANGE_RSP specifying the + version it supports. Both VNIC client and firmware must support the lower + of the two versions. Until and unless the VNIC client receives a + VERSION_EXCHANGE_RSP, no further VNIC commands may be sent. + + + + VNIC client may now use QUERY_CAPABILITY commands to interrogate + what the firmware supports currently. Multiple QUERY_CAPABILITY commands + may be send in parallel, up to one for each capability being + interrogated. + + + + Firmware will respond with QUERY_CAPABILITY_RSP messages for + each query sent. + + + + Once the queries are returned, the VNIC client uses the + REQUEST_CAPABILITY commands to inform the firmware of the capabilities it + plans on using. Until the capability has been requested and a successful + response has been received, it will not function, and commands which use + the capabilities will fail. + + + + Only the Capability-related commands are usable prior to + sending a Login command. + + + + The VNIC client determines how many Sub-CRQs to set up based on + the capabilities negotiated with the server and partition configuration, + and attempts to set those up by allocating memory, mapping them with + TCEs, and calling H_REG_SUB_CRQ iteratively for each Sub-CRQ. + + + + Once the VNIC client has successfully gotten each Sub-CRQ it + needs registered (with some possibly failing due to unavailable + resources), it parcels them out to specific queues (Transmit Completion + and Receive Completion), and does a REQUEST_CAPABILITY for the + appropriate number of each from firmware. + + + + Once the VNIC client has all SubCrqs registered, he sends a + LOGIN CRQ to the server, specifying each Sub-CRQ handle and purpose as + defined in the LOGIN command structure, and waits for a LOGIN_RSP which + includes the server’s Sub-CRQ handles and purposes. + + + + Once the LOGIN_RSP has been returned successfully, the VNIC + client is free to utilize the Transmit Submission Sub-CRQs and Receive + Buffer Add Sub-CRQs, as well as any other VNIC command. + + + + Once the VNIC client is ready to receive frames (for the + Logical Link State to transition to Link Up), it sends a + LOGICAL_LINK_STATE command to firmware. If the VNIC client is also in + control of the physical port, sending the LOGICAL_LINK_STATE command has + the side effect of initiating physical port link negotiation, as + appropriate. + + + + The firmware will send a LOGICAL_LINK_STATE_RSP once the link + state is up. + + +
+ +
+ Adapter reboot + In the event that system firmware encounters an error, needs to + update the firmware on the adapter, or needs to remove the virtualized + adapter from the partition, the following flows will happen. + + + + Firmware will close its CRQ and Sub-CRQs. + + + + VNIC client receives a TRANSPORT_EVENT specifying Partner + Partition Closed or receives an H_Closed return code on a H_SEND_CRQ or + H_SEND_SUB_CRQ hypervisor call. + + + + VNIC client closes all Sub-CRQs and CRQ using H_FREE_SUB_CRQ and + H_FREE_CRQ. (Optionally, only H_FREE_CRQ could be used to close the CRQ + and all Sub-CRQs.) + + + + VNIC client cleans up all outstanding unacknowledged transmit + frames. + + + + VNIC client cleans up all receive buffers that had been given to + the firmware. + + + + VNIC client opens the CRQ, and attempts the boot + sequence. + + +
+ +
+ Partition Mobility + In the event that an active partition is migrated to a new + platform, the following sequence takes place. + + + + VNIC client receives a TRANSPORT_EVENT event specifying Partner + Partition Suspended (Defined in + ). + + + + VNIC client pauses submission of new transmit frames and receive + add buffers. + + + + VNIC client closes all Sub-CRQs. + + + + VNIC client completes all outstanding unacknowledged transmit + frames. This may involve queueing them for retransmission once the VNIC + is recovered, or completing them as dropped, letting higher layers of the + TCP/IP stack perform retransmission. + + + + VNIC client calls H_ENABLE_CRQ until H_Success is + returned. + + + + VNIC client attempts the boot sequence. + + +
+ +
+ Dump + Typical dump collection flow: + + + + VNIC client decides on the need for a VNIC dump. + + + + VNIC client sends a REQUEST_DUMP_SIZE command (see + ) to system firmware. + + + + Firmware responds with a REQUEST_DUMP_SIZE_RSP with an estimate + on the amount of storage required to store the dump into VNIC client + memory. + + + + VNIC client allocates a buffer big enough to hold the dump, and + maps it with TCEs. + + + + VNIC client sends a REQUEST_DUMP command (see + ) to system firmware containing + the IOBAs referring to the dump buffer. + + + + System firmware uses the supplied dump buffer to collect the + memory that’s previously been registered by firmware as important + for dumps. + + + + System firmware optionally collects physical adapter debug data + into the dump buffer as well. + + + + System firmware sends a REQUEST_DUMP_RSP (see + ) to the VNIC client, + indicating the dump is complete. + + +
+ +
+ Frame Transmission + Transmission of Ethernet frames using the VNIC protocol is + accomplished using two or more Subordinate CRQs. The VNIC client + allocates one or more Transmit Completion Sub-CRQs and system firmware + allocates one or more Transmit Submission CRQs. The handles for each are + exchanged during the LOGIN processing. + The following numbered sequence details the simplified transmission + of an Ethernet frame. As with any CRQ or Subordinate CRQ based protocol, + the listed virtual interrupts may not occur for every CRQ or Sub-CRQ that + is sent using H_SEND_CRQ, H_SEND_SUB_CRQ, or H_SEND_SUB_CRQ_INDIRECT. It + is the firm intent of this protocol to allow the VNIC client and system + firmware to batch frame transmission submission and transmit complete + indications to minimize the number of virtual interrupts and to make the + transmission of Ethernet frames as efficient as possible. Multiple + Sub-CRQs may be presented to either the VNIC or system firmware with a + single virtual interrupt. + + + + Operating system chooses a VNIC adapter to use for frame + transmission. + + + + VNIC client device driver either copies the frame into a private + buffer that’s already been mapped via a TCE or maps the frame with + a TCE. + + + + VNIC client device driver constructs a Transmit Descriptor (or + multiples) describing the TCE mapped buffer (see + ). + + + + VNIC client device driver uses H_SEND_SUB_CRQ to pass the + Transmit Descriptor to system firmware’s Transmit Submission + Sub-CRQ. + + + + System firmware receives the Sub-CRQ event, and transforms it + into the appropriate format for the specific Ethernet adapter being + virtualized, and uses its embedded device driver to send the frame out + the wire. The system firmware uses RDMA to DMA the frame directly from + the VNIC client. + + + + The physical Ethernet device driver interrupts system firmware + (or system firmware polls for completion at appropriate times) indicating + the frame has been successfully transmitted. System firmware constructs a + Transmit Completion Sub-CRQ event (see + ), and places that Sub-CRQ onto + the Transmit Completion Sub-CRQ. + + + + VNIC client removes the TCE mapping for the frame, and makes it + available to its network stack. + + +
+ +
+ Frame Reception + Reception of Ethernet frames is accomplished using two or more + Sub-CRQs, similar to frame transmission. System firmware creates one or + more Receive Buffer Add Sub-CRQs and the VNIC client creates one or more + Receive Completion Sub-CRQs. + The following numbered sequence details the simplified reception of + an Ethernet frame. As with any CRQ or Subordinate CRQ based protocol, the + listed virtual interrupts may not occur for every CRQ or Sub-CRQ that is + sent using H_SEND_CRQ, H_SEND_SUB_CRQ, or H_SEND_SUB_CRQ_INDIRECT. It is + the firm intent of this protocol to allow the VNIC client and system + firmware to batch frame reception and buffer adding to minimize the + number of virtual interrupts and to make the reception of Ethernet frames + as efficient as possible. Multiple Sub-CRQs may be presented to either + the VNIC or system firmware with a single virtual interrupt. + + + + When the VNIC client is started, the VNIC allocates several + memory buffers to be used to the reception of Ethernet frames. The VNIC + client maps those buffers with TCEs using its TCE mapping + services. + + + + For each receive buffer, the VNIC client creates Add Receive + Buffer Descriptor events (see + ), and gives them to system + firmware via the Receive Buffer Add Sub-CRQ using H_SEND_SUB_CRQ or + H_SEND_SUB_CRQ_INDIRECT. Once this is done, the VNIC client should not + use or otherwise modify the receive buffer until it’s been given + back to the VNIC client using the Receive Sub-CRQ or the Sub-CRQs and CRQ + have been freed using H_FREE_SUB_CRQ and H_FREE_CRQ. + + + + As system firmware receives the Receive Buffer Add Sub-CRQ + events, it uses its physical adapter device driver to add the receive + buffer to the physical adapter’s receive queues. + + + + A frame arrives for the physical adapter off of the physical + wire, and the adapter dmas the frame directly to the VNIC client’s + memory for one of the receive buffers. + + + + System firmware receives an interrupt from the physical adapter + saying a frame has arrived, and uses the information it saves to generate + a Receive Completion event Sub-CRQ (see + ), and places it on the + appropriate Receive Completion Sub-CRQ. + + + + The VNIC client receives a virtual interrupt for its Receive + Completion Sub-CRQ, and passes the frame up its network stack. + + +
+
+
+ VNIC Commands + All VNIC commands are sent using H_SEND_CRQ. +
+ Version Exchange + The VERSION_EXCHANGE command as defined in + allow the VNIC protocol to be + easily updated in the future. Each side is required to support the + highest common version of the VNIC protocol specification, as exchanged + right after the low level CRQ registration flows. + + + VERSION_EXCHANGE and VERSION_EXCHANGE_RSP + Command + + + + + + + + + + Field Name + + + + + ByteOffset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This field should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field should be either VERSION_EXCHANGE or + VERSION_EXCHANGE_RSP. + + + + + Version + + + 2 + + + 2 + + + Maximum version that VNIC client supports on a + VERSION_EXCHANGE and the maximum version that system firmware + supports on a VERSION_EXCHANGE_RSP. Each side must support the + highest common version between the two versions. A value from + will be contained in + this field. + + + + + Reserved + + + 4 + + + 8 + + + This field is reserved, and should be set to 0. + + + + + Return Code + + + 12 + + + 4 + + + This is a return code for the operation as defined in + . + + + + +
+   + + VNIC Protocol Versions + + + + + + + + + Value + + + + + Definition + + + + + + + + 1 + + + Initial VNIC protocol version + + + + + 2-65535 + + + Reserved + + + + +
+
+
+ VNIC Capabilities + The VNIC capabilities command as defined in + is used to create an abstracted + architecture for discovering and utilizing different NIC advanced + functions on adapters, in an adapter-independent manner. As new + capabilities are introduced in adapters, more capability values will be + added. + To discover which capabilities a VNIC currently supports, multiple + QUERY_CAPABILITY commands should be sent from the VNIC client for each + capability of interest. System firmware will return the current + capability setting, or a bad return code if the capability isn’t + supported. System firmware will return UnsupportedOption for any + capability it doesn’t understand. + If the VNIC client wishes to use one of the supported capabilities, + it must be enabled via the correct REQUEST_CAPABILITY command. If a + capability has a variable number of settings (settable via the Number + field), and system firmware doesn’t support the value, a + PartialSuccess return code will be returned with the capped value in the + response. + If the VNIC client wishes to use REQUEST_CAPABILITY to determine if + any specific capabilities are valid without performing QUERY_CAPABILITY + commands, that’s acceptable, but there may be side effects as a + result. + + + CAPABILITIES Commands + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This field should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field should be QUERY_CAPABILITIES, + REQUEST_CAPABILITIES, or their associated responses. + + + + + Capability + + + 2 + + + 2 + + + This value should be one of the values from + . + + + + + Number + + + 4 + + + 8 + + + This field is used for both REQUESTs and QUERYs. For a + REQUEST, it’s the value that the VNIC client wishes to + use. On any RSP, it’s the new (or unchanged) current + value of the capability. + + + + + Return Code + + + 12 + + + 4 + + + This is a return code for the operation as defined in + . + + + + +
+   + + VNIC Capabilities + + + + + + + + + Value + + + + + Field Name + + + + + Behavior + + + + + + + + 1 + + + Minimum Number of firmware-supported Transmit + Completion/Submission Queues + + + - Query-only- Integer value returned in Number + + + + + 2 + + + Minimum Number of firmware-supported Receive Completion + Queues + + + - Query-only- Integer value returned in Number + + + + + 3 + + + Minimum Number of firmware-supported Receive Buffer Add + Queues per Receive Completion Queue + + + - Query-only- Integer value returned in Number + + + + + 4 + + + Maximum Number of firmware-supported Transmit + Completion/Submission Queues + + + - Query-only- Integer value returned in Number + + + + + 5 + + + Maximum Number of firmware-supported Receive Completion + Queues + + + - Query-only- Integer value returned in Number + + + + + 6 + + + Maximum Number of firmware-supported Receive Buffer Add + Queues per Receive Completion Queue + + + - Query-only- Integer value returned in Number + + + + + 7 + + + Requested Number of Transmit Completion/Submission + Queues + + + - Settable- Positive integer value set and returned in Number + + + + + 8 + + + Requested Number of Receive Completion Queues + + + - Settable- Positive integer value set and returned in Number + + + + + 9 + + + Requested Number of Receive Buffer Add Queues per Receive + Completion Queue + + + - Settable- Positive integer value set and returned in Number + + + + + 10 + + + Minimum Number of Transmit Entries Per Sub-CRQ + + + - Query only- Positive integer value set and returned in Number + + + + + 11 + + + Minimum Number of Receive Buffer Add Entries per + Sub-CRQ + + + - Query only- Positive integer value set and returned in Number + + + + + 12 + + + Maximum Number of Transmit Entries Per Sub-CRQ + + + - Query only- Positive integer value set and returned in Number + + + + + 13 + + + Maximum Number of Receive Buffer Add Entries per + Sub-CRQ + + + - Query only- Positive integer value set and returned in Number + + + + + 14 + + + Requested Number of Transmit Entries Per Sub-CRQ + + + - Settable- Positive integer value set and returned in Number + + + + + 15 + + + Requested Number of Receive Buffer Add Entries per + Sub-CRQ + + + - Settable- Positive integer value set and returned in Number + + + + + 16 + + + TCP/IP offload supported + + + - Query only- Boolean value returned in Number. If TRUE, TCP/IP + offload commands defined in + are supported. + + + + + 17 + + + Promiscuous mode requested + + + - Settable- Boolean value returned in Number + + + + + 18 + + + Promiscuous mode supported + + + - Query only- Boolean value returned in Number + + + + + 19 + + + Minimum MTU size + + + - Query only- Positive integer value set and returned in Number + + + + + 20 + + + Maximum MTU size + + + - Query only- Positive integer value set and returned in Number + + + + + 21 + + + Requested MTU size + + + - Settable + - Positive integer value set and returned in + Number + - This setting can impact the minimum number of queues or + receive buffer sizes supported, and should either be set early + or other capabilities will need to be reevaluated. + + + + + 22 + + + Maximum Number of Unique Multicast MAC address + filters + + + - Query only- Positive integer value set and returned in Number + + + + + 23 + + + VLAN Header insertion supported + + + - Query only + - Boolean value returned in Number + - This is controlled on a packet by packet basis in the + transmit descriptor. + + + + + 24 + + + Reserved + + +   + + + + + 25 + + + Maximum Transmit Scatter Gather entries + + + - Query only + - Positive integer value reflecting the maximum number of + IOBAs that can be used to describe a single frame using + Transmit Descriptors. + + + + + 26 + + + Receive Scatter/Gather Mode supported + + + - Query only + - Boolean value set and returned in Number. + - If supported, this can enable chaining of receive + buffers together to minimize the amount of memory that needs to + be added in the form of Receive Buffers (Particularly if Large + Receive Offload is enabled). + + + + + 27 + + + Receive Scatter/Gather Mode Requested + + + - Settable + - Boolean value set and returned in Number. + - This setting can impact the number of queues or receive + buffer sizes supported, and should be set before configuring + those values. + + + + + 28-65535 + + + Reserved + + +   + + + + +
+
+
+ Login Support + The use of the LOGIN and LOGIN_RSP commands is defined in + . The format of the LOGIN + command is defined in + , and the LOGIN_RSP command is + defined in + . + There must be exactly one Transmit Submission Sub-CRQ for each + Transmit Completion Sub-CRQ, and vice versa. Each is implicitly tied to + the other by virtue of the order each appears in the array of handles in + the LOGIN Buffer and LOGIN Response buffer. (i.e. The first entry in each + are associated, the second entry in each are associated, etc.) + + + LOGIN Request + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This should be set to LOGIN. + + + + + Reserved + + + 2 + + + 6 + + + This field is reserved, and should be set to 0. + + + + + IOBA + + + 8 + + + 4 + + + This field is an I/O bus address referring to a + TCE-mapped buffer containing the LOGIN Buffer as defined in + . + + + + + Length + + + 12 + + + 4 + + + This field is the length of the TCE-mapped LOGIN buffer. + This value should match that as seen in the LOGIN + Buffer. + + + + +
+   + + LOGIN Buffer + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + Total Length + + + 0 + + + 4 + + + This field is the total length of the LOGIN + Buffer. + + + + + Version + + + 4 + + + 4 + + + This field contains the version of LOGIN Buffer layout. + The initial version should be set to 1. + + + + + Number of Transmit Completion Sub-CRQs + + + 8 + + + 4 + + + This field contains the number of Transmit Completion + Sub-CRQs as allocated by the VNIC client. + + + + + Offset to Transmit Completion Sub-CRQ handles + + + 12 + + + 4 + + + Offset from the beginning of the LOGIN buffer to the + start of an array of 8 byte elements containing the array of + Transmit Completion Sub-CRQ handles. + + + + + Number of Receive Completion Sub-CRQs + + + 16 + + + 4 + + + This field contains the number of Receive Completion + Sub-CRQs as allocated by the VNIC client. + + + + + Offset to Receive Completion Sub-CRQ handles + + + 20 + + + 4 + + + Offset from the beginning of the LOGIN Buffer to the + start of an array of 8 byte elements containing the array of + Receive Completion Sub-CRQ handles. + + + + + Login Response buffer IOBA + + + 24 + + + 4 + + + This field contains an I/O buffer address referencing a + TCE-mapped buffer to be used for the system firmware to place + its LOGIN Response buffer containing its variable length array + of Sub-CRQ handles. This can point to the same storage as the + LOGIN Buffer, as necessary. + + + + + Login Response buffer length + + + 28 + + + 4 + + + This field contains the length of the Login Response + buffer described in the Login Response buffer IOBA. The VNIC + client needs to ensure that system firmware will have enough + space to place each Sub-CRQ handle as requested prior to LOGIN + using REQUEST_CAPABILITY commands. + + + + + Transmit Completion Sub-CRQ handle array + + + variable + + + variable + + + This is a variable sized array containing the Sub-CRQ + handles obtained from H_REGISTER_SUB_CRQ for the Transmit + Completion Sub-CRQ handles. + + + + + Receive Completion Sub-CRQ handle array + + + variable + + + variable + + + This is a variable sized array containing the Sub-CRQ + handles obtained from H_REGISTER_SUB_CRQ for the Receive + Completion Sub-CRQ handles. + + + + +
+   + + LOGIN Response Buffer + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + Total Length + + + 0 + + + 4 + + + This field is the total length of the Login Response + Buffer. + + + + + Version + + + 4 + + + 4 + + + This field contains the version of LOGIN Response Buffer + layout. The initial version should be set to 1. + + + + + Number of Transmit Submission Sub-CRQs + + + 8 + + + 4 + + + This field contains the number of Transmit Submission + Sub-CRQs as requested by the VNIC client and allocated by + firmware. + + + + + Offset to Transmit Submission Sub-CRQ handles + + + 12 + + + 4 + + + Offset from the beginning of the LOGIN Response Buffer to + the start of an array of 8 byte elements containing the array + of Transmit Submission Sub-CRQ handles. + + + + + Number of Receive Buffer Add Sub-CRQs + + + 16 + + + 4 + + + This field contains the total number of Receive Buffer + Add Sub-CRQs as requested by the VNIC client and allocated by + the firmware. The first n correspond to the first Receive + Completion Sub-CRQ, the next n to the second, etc., where n is + the Requested number of Receive Buffer Add Sub-CRQs per Receive + Completion Queue requested by the VNIC client. + + + + + Offset to Receive Buffer Add Sub-CRQ handles + + + 20 + + + 4 + + + Offset from the beginning of the LOGIN Response Buffer to + the start of an array of 8 byte elements containing the array + of Receive Buffer Add Sub-CRQ handles. + + + + + Offset to Receive Buffer Add Buffer Size + + + 24 + + + 4 + + + Offset from the beginning of the LOGIN Response Buffer to + the start of an array of 8 byte sizes. There is one size for + each Receive Buffer Add Sub-CRQ, and each size represents the + receive buffer size possible for that specific Receive Buffer + Add Sub-CRQ. + + + + + Number of Supported Transmit Descriptors + + + 28 + + + 4 + + + This field contains the number of supported Transmit + Descriptors, as detailed in + . + + + + + Offset to Supported Transmit Descriptors array + + + 32 + + + 4 + + + Offset from the beginning of the LOGIN Response Buffer to + the start of an array of 1 byte values. There is one value for + each supported Transmit Descriptor format, sorted so the + formats with best performance will be first in the + array. + + + + + Transmit Submission Sub-CRQ handle array + + + variable + + + variable + + + This is a variable sized array containing the Sub-CRQ + handles obtained from H_REGISTER_SUB_CRQ for the Transmit + Submission Sub-CRQ handles. + + + + + Receive Buffer Add Sub-CRQ handle array + + + variable + + + variable + + + This is a variable sized array containing the Sub-CRQ + handles obtained from H_REGISTER_SUB_CRQ for the Receive Buffer + Add Sub-CRQ handles. + + + + + Receive Buffer Add Buffer Size array + + + variable + + + variable + + + This is a variable sized array containing the Receive + Buffer Sizes must use for the respective Receive Buffer Add + Sub-CRQs. + + + + + Supported Transmit Descriptors array + + + variable + + + variable + + + This is a variable sized array containing the + performance-order sorted array of one byte supported Transmit + Descriptor formats. + + + + +
+   + + LOGIN_RSP Command + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This should be set to LOGIN_RSP. + + + + + Reserved + + + 2 + + + 10 + + + This field is reserved, and should be set to 0. + + + + + Return Code + + + 12 + + + 4 + + + This is a return code for the operation as defined in + . + + + + +
+
+
+ Physical Port Parameters + A VNIC client may always use the QUERY_PHYS_PARM command to + retrieve information about the current physical port state such as + current link speed and state. + A VNIC client may always use the QUERY_PHYS_CAPABILITIES command to + retrieve information about the current capabilities of the physical + adapter associated with the VNIC, including allowed speed, duplex, and + ability to modify those values. + If the VNIC client wishes to determine all bits that are supported + by firmware, it may choose to send a QUERY_PHYS_CAPABILITIES command with + no bits turned on. Firmware will respond with all possible bits it + supports. If the VNIC client wishes to determine if a specific bit + combination is supported by firmware, it may turn on those specific bit + combinations. In that case, firmware will validate the combination, and + validate the specific combination. + If the system administrator has configured the VNIC to have + physical port configuration authority, the VNIC client may also use the + SET_PHYS_PARMS command to change those values. + The SET_PHYS_PARMS, QUERY_PHYS_PARMS, and QUERY_PHYS_CAPABILITIES + commands all use a common command format defined in + . + + + Physical Port Parameters Commands + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be either SET_PHYS_PARMS, + QUERY_PHYS_PARMS, QUERY_PHYS_CAPABILITIES, or the respective + response values. + + + + + Flags + + + 2 + + + 1 + + + The following bits are used to either request the + specific capability on a SET_PHYS_PARMS, indicate the + capability to use that capability on a QUERY_PHYS_CAPABILITIES, + or return the current value of the capability on a + QUERY_PHYS_PARMS command. + Bit 0: External loopback mode + Bit 1: Internal loopback mode + Bit 2: Promiscuous mode + Bit 3: Physical Link Active (VNIC can communicate onto + the physical media) + Bit 4: Autonegotiate Duplex + Bit 5: Full duplex mode + Bit 6: Half duplex mode + Bit 7: If set, the VNIC has the ability to change + physical port parameters. + + + + + Flags + + + 3 + + + 1 + + + Bit 0: Adapter Logical Link Active (multiple VNICs on the + same adapter can communicate) + Bit 1-7: Reserved + + + + + Speed + + + 4 + + + 4 + + + The following bits are used to either request the + specific speed on a SET_PHYS_PARMS, indicate the capability to + use that speed on a QUERY_PHYS_CAPABILITIES, or return the + current speed on a QUERY_PHYS_PARMS command. + Bit 0: Autonegotiate speed + Bit 1: 10 megabit speed + Bit 2: 100 megabit speed + Bit 3: 1 gigabit speed + Bit 4: 10 gigabit speed + Bit 5-31: These bits are reserved, and should be set to + 0. + + + + + MTU + + + 8 + + + 4 + + + This field is used to request a MTU for this VNIC client, + and to return the current MTU setting. If this value exceeds + the allowed value in the case where there are multiple VNICs + associated with the same physical adapter, this MTU will be + capped to an allowable value, and a PartialSuccess return code + will be returned on the SET_PHYS_PARMS command. + + + + + Return Code + + + 12 + + + 4 + + + On a response, this is a return code for the operation as + defined in + . + + + + +
+
+
+ Logical Link State + When the VNIC does not have authority to change the physical port + parameters, the LOGICAL_LINK_STATE command and response provide a method + for the VNIC to inform system firmware when it’s ready to receive + packets. The format of the LOGICAL_LINK_STATE and LOGICAL_LINK_STATE_RSP + commands is defined in + . + The current VNIC logical link state will always be returned in the + Link State field on a LOGICAL_LINK_STATE_RSP. + + + LOGICAL_LINK_STATE and LOGICAL_LINK_STATE_RSP + commands + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be either LOGICAL_LINK_STATE or + LOGICAL_LINK_STATE_RSP. + + + + + Link State + + + 2 + + + 1 + + + This field is used to request a logical link state change + by the VNIC client without a corresponding change to the + physical link state. The intended use for this is when a VNIC + client is associated with a NIC VF that doesn’t have + control over the physical port to control when the VNIC client + receives incoming frames. + If this field is a 0, the link should be down, if the + field is a 1, the link should be up. + if this field is 0xFF, no logical link state change will + be done, and the current logical link state will be returned in + the response. + + + + + Reserved + + + 3 + + + 9 + + + This field is reserved, and should be set to 0. + + + + + Return Code + + + 12 + + + 4 + + + This is a return code for the operation as defined in + . + + + + +
+
+
+ TCP, UDP, and IP Offload Support + The QUERY_IP_OFFLOAD command as defined in + allows the VNIC client to + determine what facilities exist in the VNIC system firmware, and its + limitations, if any. + Based on the capabilities and limitations, the CONTROL_IP_OFFLOAD + command as defined in + allows the VNIC client to + enable appropriate offload capabilities. QUERY_IP_OFFLOAD and + CONTROL_IP_OFFLOAD must be done prior to successful LOGIN + exchange. + All offload parameters are off by default. + + + QUERY_IP_OFFLOAD and QUERY_IP_OFFLOAD_RSP + Commands + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be either QUERY_IP_OFFLOAD or + QUERY_IP_OFFLOAD_RSP. + + + + + Reserved + + + 2 + + + 2 + + + This field is reserved, and should be set to 0. + + + + + Length + + + 4 + + + 4 + + + This field contains the length of the QUERY_IP_OFFLOAD + buffer + + + + + IOBA + + + 8 + + + 4 + + + This field is an I/O bus address referring to a + TCE-mapped buffer used by system firmware to return IP offload + information. On reception of a successful QUERY_IP_OFFLOAD_RSP, + the buffer will be filled in with the structure as defined in + . + + + + + Return Code + + + 12 + + + 4 + + + This is a return code for the operation as defined in + . + + + + +
+   + + CONTROL_IP_OFFLOAD and CONTROL_IP_OFFLOAD_RSP + Command + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be CONTROL_IP_OFFLOAD or + CONTROL_IP_OFFLOAD_RSP. + + + + + Reserved + + + 2 + + + 2 + + + This field is reserved, and should be set to 0. + + + + + IOBA + + + 4 + + + 4 + + + This field is an I/O bus address referring to a + TCE-mapped buffer containing the parameters to enable or + disable TCP, UDP, and IP offload. The format of this buffer is + defined in + . + + + + + Length + + + 8 + + + 4 + + + This field contains the length of the CONTROL_IP_OFFLOAD + buffer. + + + + + Return Code + + + 12 + + + 4 + + + This is a return code for the operation as defined in + . + + + + +
+   + + QUERY_IP_OFFLOAD Buffer + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + Total Length + + + 0 + + + 4 + + + This field is the total length of the QUERY_IP_OFFLOAD + Buffer. + + + + + Version + + + 4 + + + 4 + + + This field contains the version of QUERY_IP_OFFLOAD + Buffer layout. The initial version should be 1. + + + + + IPv4 Checksum offload supported + + + 8 + + + 1 + + + This field is 1 if supported + + + + + IPv6 Checksum offload supported + + + 9 + + + 1 + + + This field is 1 if supported. + + + + + TCP over IPv4 checksum offload supported + + + 10 + + + 1 + + + This field is 1 if supported. + + + + + TCP over IPv6 checksum offload supported + + + 11 + + + 1 + + + This field is 1 if supported. + + + + + UDP over IPv4 checksum offload supported + + + 12 + + + 1 + + + This field is 1 if supported. + + + + + UDP over IPv6 checksum offload supported + + + 13 + + + 1 + + + This field is 1 if supported. + + + + + Large send offload over IPv4 supported + + + 14 + + + 1 + + + This field is 1 if supported. + + + + + Large send offload over IPv6 supported + + + 15 + + + 1 + + + This field is 1 if supported. + + + + + Large receive offload over IPv4 supported + + + 16 + + + 1 + + + This field is 1 if supported. + + + + + Large receive offload over IPv4 supported + + + 17 + + + 1 + + + This field is 1 if supported. + + + + + Reserved + + + 18 + + + 14 + + + This field is reserved, and is set to 0. + + + + + Maximum IPv4 header size + + + 32 + + + 2 + + + This field contains the maximum size of the IPv4 header + for offload operations, or 0xFFFF if no limit. + + + + + Maximum IPv6 header size + + + 34 + + + 2 + + + This field contains the maximum size of the IPv6 header + for offload operations, or 0xFFFF if no limit. + + + + + Maximum TCP header size + + + 36 + + + 2 + + + This field contains the maximum size of the TCP header + for offload operations, or 0xFFFF if no limit. + + + + + Maximum UDP header size + + + 38 + + + 2 + + + This field contains the maximum size of the UDP header + for offload operations, or 0xFFFF if no limit. + + + + + Maximum Large send offload size + + + 40 + + + 4 + + + This field contains the maximum size of a pseudo-frame + for large send offload operations, or 0xFFFFFFFF if no + limit. + + + + + Maximum Large receive offload size + + + 44 + + + 4 + + + This field contains the maximum size of a pseudo-frame + for large receive offload operations, or 0xFFFFFFFF if no + limit. + + + + + Reserved + + + 48 + + + 16 + + + This field is reserved, and is set to 0. + + + + + IPv6 Extension Header supported + + + 64 + + + 1 + + + This field contains a 0 if no extension headers are + supported. + This field contains a 1 if extension headers are + supported with limits + This field contains a 0xFF if all IPv6 extension headers + are supported + + + + + TCP Pseudosum required + + + 65 + + + 1 + + + This field is 0 if no pseudosum is required in the + frame. + This field is 1 if a standard pseudosum is required to be + put in the frame. + All other values are reserved. + + + + + Reserved + + + 66 + + + 30 + + + This field is reserved, and is set to 0. + + + + + Number of IPv6 extension headers supported + + + 96 + + + 2 + + + This field must be non zero if the IPv6 Extension Header + supported field is 1. + + + + + Offset to List of supported IPv6 extension headers + + + 98 + + + 4 + + + This field contains an offset from the start of the + QUERY_IP_OFFLOAD buffer to the array of supported extension + header values. + + + + + Reserved + + + 102 + + + 154 + + + This field is reserved, and should be set to 0. + + + + + Array of IPv6 extension header types + + + variable + + + variable + + + This is an array of one byte values that are the + extension header types supported by IPv6 offload. + + + + +
+   + + CONTROL_IP_OFFLOAD Buffer + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + Total Length + + + 0 + + + 4 + + + This field is the total length of the CONTROL_IP_OFFLOAD + Buffer. + + + + + Version + + + 4 + + + 4 + + + This field contains the version of CONTROL_IP_OFFLOAD + Buffer layout. The initial version should be set to 1. + + + + + Enable IPv4 Checksum offload + + + 8 + + + 1 + + + This field is 1 if desired + + + + + Enable IPv6 Checksum offload + + + 9 + + + 1 + + + This field is 1 if desired. + + + + + Enable TCP over IPv4 checksum offload + + + 10 + + + 1 + + + This field is 1 if desired. + + + + + Enable TCP over IPv6 checksum offload + + + 11 + + + 1 + + + This field is 1 if desired. + + + + + Enable UDP over IPv4 checksum offload + + + 12 + + + 1 + + + This field is 1 if desired. + + + + + Enable UDP over IPv6 checksum offload + + + 13 + + + 1 + + + This field is 1 if desired. + + + + + Enable Large send offload over IPv4 + + + 14 + + + 1 + + + This field is 1 if desired. + + + + + Enable Large send offload over IPv6 + + + 15 + + + 1 + + + This field is 1 if desired. + + + + + Enable bad packet reception + + + 16 + + + 1 + + + This field is 1 if desired + + + + + Reserved + + + 17 + + + 111 + + + This field is reserved, and should be set to 0. + + + + +
+
+
+ Dump Support + The dumps collected via the VNIC interface is a smart dump that + depends upon a working device driver. If the portion of system firmware + servicing the physical adapter has run into catastrophic problems, an + entire memory image of the associated firmware will be collected + automatically, and collected in a similar fashion to platform + dumps. + If the VNIC client detects that the VNIC interface is not providing + the services in the manner it expects, it may utilize the dump support to + collect focused debugging data collected and stored in VNIC client + storage that’s been TCE-mapped. + The format of the REQUEST_DUMP command is defined in + , and the format of the + REQUEST_DUMP_RSP command is defined in + . + + + REQUEST_DUMP_SIZE and REQUEST_DUMP_SIZE_RSP + Commands + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be either REQUEST_DUMP_SIZE or + REQUEST_DUMP_SIZE_RSP. + + + + + Reserved + + + 2 + + + 6 + + + This field is reserved, and should be set to 0. + + + + + Length + + + 8 + + + 4 + + + This field is set to the estimated length of the VNIC + dump in the REQUEST_DUMP_RSP if the return code was + Success. + + + + + Return Code + + + 12 + + + 4 + + + This is a return code for the operation as defined in + . + + + + +
+   + + REQUEST_DUMP Command + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be REQUEST_DUMP. + + + + + Reserved + + + 2 + + + 2 + + + This field is reserved, and should be set to 0. + + + + + IOBA + + + 4 + + + 4 + + + This field is an I/O bus address referring to a + TCE-mapped buffer used by system firmware to place the VNIC + dump. + + + + + Length + + + 8 + + + 4 + + + This field contains the length of the VNIC dump + buffer. + + + + + Reserved + + + 12 + + + 4 + + + This field is reserved and should be set to 0. + + + + +
+   + + REQUEST_DUMP_RSP Command + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be REQUEST_DUMP_RSP. + + + + + Reserved + + + 2 + + + 6 + + + This field is reserved, and should be set to 0. + + + + + Dumped Length + + + 8 + + + 4 + + + This field contains the amount of data placed into the + dump buffer. + + + + + Return Code + + + 12 + + + 4 + + + This is a return code for the operation as defined in + . + + + + +
+
+
+ Reliability, Availability, and Service (RAS) Support + The VNIC RAS support allows the tracing of information within + system firmware, and control of consistency checking done by firmware. + Individual components of firmware will be exposed to the VNIC Client, and + each component can independently have their tracing and error checking + levels increased and decreased. Each individual component’s trace + information can be collected independently from others. + Trace entries will be returned to the VNIC client in timebase + order. + The upper 16 bits of the trace ID for the Firmware Trace Data + Format are an AIX RAS tracehook ID, and the lower 16 bits are an AIX RAS + subhookid. + Prior to a successful LOGIN request, all components related to the + VNIC may not be available in the list of components. To get a complete + list of all possible components, the RAS commands should be delayed until + after a successful LOGIN unless a pre-LOGIN problem is being + diagnosed. + The CONTROL_RAS command can be used to resize the individual + components’ trace buffers, but due to the limited memory available + in the system firmware, increasing the sizes of one trace buffer may + require decreasing the size of a different component’s trace + buffer. + The REQUEST_RAS_COMP_NUM and REQUEST_RAS_COMP_NUM_RSP commands are + defined in + , and the REQUEST_RAS_COMPS and + REQUEST_RAS_COMPS_RSP command format is defined in + . The COLLECT_FW_TRACE and + COLLECT_FW_TRACE_RSP commands are defined in + . + + + REQUEST_RAS_COMP_NUM and REQUEST_RAS_COMP_NUM_RSP + Commands + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be REQUEST_RAS_COMP_NUM or + REQUEST_RAS_COMP_NUM_RSP. + + + + + Reserved + + + 2 + + + 2 + + + This field is reserved, and should be set to 0. + + + + + Number of Components + + + 4 + + + 4 + + + This field contains the number of individual firmware + components whose RAS characteristics can be independently + modified. + + + + + Reserved + + + 8 + + + 4 + + + This field is reserved, and should be set to 0. + + + + + Return Code + + + 12 + + + 4 + + + On a response, this field will contain a return code for + the request as defined in + . This field is + reserved for a request. + + + + +
+ . + + REQUEST_RAS_COMPS and REQUEST_RAS_COMPS_RSP + Commands + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be REQUEST_RAS_COMPS or + REQUEST_RAS_COMPS_RSP. + + + + + Reserved + + + 2 + + + 2 + + + This field is reserved, and should be set to 0. + + + + + IOBA + + + 4 + + + 4 + + + This field contains an I/O bus address of a TCE-mapped + buffer containing an array of Firmware Component structures as + defined in + . The VNIC client + should ensure the buffer is large enough to contain the number + of components as returned in a REQUEST_RAS_COMP_NUM_RSP + command. + + + + + Length + + + 8 + + + 4 + + + This field is the length of the buffer referred to by the + IOBA field. It should be some multiple of the size of the + Firmware Component format. + + + + + Return Code + + + 12 + + + 4 + + + This is a return code for the operation as defined in + . + + + + +
+   + + CONTROL_RAS and CONTROL_RAS_RSP Commands + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be CONTROL_RAS or CONTROL_RAS_RSP. + + + + + Correlator + + + 2 + + + 1 + + + This field contains a Correlator for a Firmware Component + as defined in + that this command + should act on. + + + + + Level + + + 3 + + + 1 + + + This value should be a value between 0 and 9, where a + larger number indicates a higher detail of tracing or error + checking. + + + + + Operation + + + 4 + + + 1 + + + This field controls what action the CONTROL_RAS command + performs. + If this value is a 1, use the Level field to modify the + current trace level of the specified component. + If this value is a 2, use the Level field to modify the + current error checking level of the specified component. + If this value is a 3, suspend the tracing for the + specified component that was previously on. + If this value is a 4, resume the tracing for the + specified component that was previously suspended. + If this value is a 5, turn tracing for the specified + component on. + If this value is a 6, turn tracing for the specified + component off. + If this value is a 7, change the size of the specified + trace buffer for the specified component. + All other values are reserved. + + + + + Trace Buffer Size + + + 5 + + + 3 + + + If Operation is a 7, this field contains the requested + size of the specified trace buffer. On a response, will be + filled in with the current size of the trace buffer. + For all other Operation values, this field is + reserved. + + + + + Reserved + + + 8 + + + 4 + + + This field is reserved, and should be set to 0. + + + + + Return Code + + + 12 + + + 4 + + + This is a return code for the operation as defined in + . + + + + +
+   + + COLLECT_FW_TRACE and COLLECT_FW_TRACE_RSP + Commands + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be COLLECT_FW_TRACE or + COLLECT_FW_TRACE_RSP. + + + + + Correlator + + + 2 + + + 1 + + + This field contains a Correlator for a Firmware Component + as defined in + that this command + should act on. + + + + + Reserved + + + 3 + + + 1 + + + This field is reserved, and should be set to 0. + + + + + IOBA + + + 4 + + + 4 + + + This field contains the I/O bus address of a TCE-mapped + buffer of the indicated size that will be used by firmware to + return the trace. + + + + + Buffer Length + + + 8 + + + 4 + + + This field contains the length of the buffer in bytes + used to collect the trace information. On a COLLECT_FW_RSP, + this value will indicate how much trace data is actually placed + in the buffer. The trace data is an array of entries with the + format as defined in + . + + + + + Return Code + + + 12 + + + 4 + + + This is a return code for the operation as defined in + . + + + + +
+   + + Firmware Trace Data Entry Format + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + + + + Trace ID + + + 0 + + + 4 + + + + + Number Valid Trace Data + + + 4 + + + 1 + + + + + Reserved + + + 5 + + + 3 + + + + + PMC Registers + + + 8 + + + 8 + + + + + Timebase + + + 16 + + + 8 + + + + + Trace Data 1 + + + 24 + + + 8 + + + + + Trace Data 2 + + + 32 + + + 8 + + + + + Trace Data 3 + + + 40 + + + 8 + + + + + Trace Data 4 + + + 48 + + + 8 + + + + + Trace Data 5 + + + 56 + + + 8 + + + + +
+   + + Firmware Component Format + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + Component Name + + + 0 + + + 48 + + + This field contains an ASCII string containing a readable + name of the component. + + + + + Trace Buffer Size + + + 48 + + + 4 + + + This field contains the size of the trace buffer. + + + + + Correlator + + + 52 + + + 1 + + + This field contains a value to be used on a + COLLECT_FW_TRACE or CONTROL_RAS command to identify which + component to operate on. + + + + + Trace Level + + + 53 + + + 1 + + + This field shows the current trace level, as defined in + . + A value of 0xFF indicates this component does not support + tracing. + + + + + Parent Correlator + + + 54 + + + 1 + + + This field contains the correlator of the parent + component. If this value is 0xFF, there is no parent. + + + + + Error Checking + + + 55 + + + 1 + + + This field contains the error checking level for this + component. It contains a value from 0-9, where 0 means no extra + error checking, and 9 means the highest level of consistency + checking. + A value of 0xFF indicates this component does not support + changing its level of error checking. + + + + + Trace State + + + 56 + + + 1 + + + If this field is a 0, the component’s tracing is + turned off. If this field is a 1, the component’s tracing + is turned on. + + + + + Reserved + + + 57 + + + 7 + + + This field is reserved, and should be set to 0. + + + + + Description + + + 64 + + + 192 + + + This field contains an ASCII string containing a readable + description of the component. + + + + +
+
+
+ Statistics Support + The REQUEST_STATISTICS command as defined in + is used by the VNIC client to + obtain statistic counters kept by system firmware and the physical + adapter supporting the VNIC. + The REQUEST_STATISTICS_RSP command is defined in + . + In the event a given VNIC does not support the retrieval of certain + of the statistics, the statistic will have a -1 value returned in + it. + The REQUEST_DEBUG_STATS command defined in + is used by the VNIC client to + retrieve an unarchitected block of statistics that is implementation + dependent which may be used to debug firmware problems. This is an + optional command, and the actual data returned may vary from + implementation to implementation. + + + REQUEST_STATISTICS Command + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be REQUEST_STATISTICS. + + + + + Flags + + + 2 + + + 1 + + + Bit 0: If set, retrieve the physical port statistics. If + the VNIC doesn’t have authority to retrieve the physical + port statistics, the command may fail. If this bit is 0, + retrieve the logical port statistics. + Bit 1: If this field is set to 1, clear the statistics. + If this field is set to 0, do not clear any statistics. + Bit 2-7: This fields are reserved, and should be set to + 0. + + + + + Reserved + + + 3 + + + 1 + + + This field is reserved, and should be set to 0. + + + + + IOBA + + + 4 + + + 4 + + + This field is an I/O bus address referring to a + TCE-mapped buffer used by system firmware to place the VNIC + statistics block as defined in + . + + + + + Length + + + 8 + + + 4 + + + This field contains the length of the VNIC statistics + buffer. + + + + + Reserved + + + 12 + + + 4 + + + This field is reserved and should be set to 0. + + + + +
+   + + REQUEST_STATISTICS_RSP Command + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be REQUEST_STATISTICS_RSP. + + + + + Reserved + + + 2 + + + 2 + + + This field is reserved, and should be set to 0. + + + + + Reserved + + + 4 + + + 8 + + + This field is reserved and should be set to 0. + + + + + Return Code + + + 12 + + + 4 + + + This is a return code for the operation as defined in + . + + + + +
+   + + VNIC Statistics Version 1 + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + + + + Version + + + 0 + + + 4 + + + + + Promiscuous + + + 4 + + + 4 + + + + + Received Packets + + + 8 + + + 8 + + + + + Bytes Received + + + 16 + + + 8 + + + + + Packets Sent + + + 24 + + + 8 + + + + + Bytes Sent + + + 32 + + + 8 + + + + + Unicast Packets Sent + + + 40 + + + 8 + + + + + Unicast Packets Received + + + 48 + + + 8 + + + + + Multicast Packets Sent + + + 56 + + + 8 + + + + + Multicast Packets Received + + + 64 + + + 8 + + + + + Broadcast Packets Sent + + + 72 + + + 8 + + + + + Broadcast Packets Received + + + 80 + + + 8 + + + + + Alignment Errors + + + 88 + + + 8 + + + + + FCS Errors + + + 96 + + + 8 + + + + + Single Collision Frames + + + 104 + + + 8 + + + + + Multiple Collision Frames + + + 112 + + + 8 + + + + + SQE Test Errors + + + 120 + + + 8 + + + + + Deferred Transmissions + + + 128 + + + 8 + + + + + Late Collisions + + + 136 + + + 8 + + + + + Excess Collisions + + + 144 + + + 8 + + + + + Internal MAC Transmit Errors + + + 152 + + + 8 + + + + + Carrier Sense + + + 160 + + + 8 + + + + + Too Long Frames + + + 168 + + + 8 + + + + + Internal MAC Receive Errors + + + 176 + + + 8 + + + + + DMA Receive Overrun + + + 184 + + + 8 + + + + + DMA Transmit Underrun + + + 192 + + + 8 + + + + + Receive No Resource + + + 200 + + + 8 + + + + + Too Short Frames + + + 208 + + + 8 + + + + + Reserved + + + 216 + + + 40 + + + + +
+   + + REQUEST_DEBUG_STATS command + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be REQUEST_DEBUG_STATS or + REQUEST_DEBUG_STATS_RSP. + + + + + Reserved + + + 2 + + + 2 + + + This field is reserved, and should be set to 0. + + + + + IOBA + + + 4 + + + 4 + + + This field is an I/O bus address referring to a + TCE-mapped buffer used by system firmware to place the VNIC + debug statistics block. + + + + + Length + + + 8 + + + 4 + + + This field contains the length of the VNIC statistics + buffer. On a REQUEST_DEBUG_STATS_RSP, contains the amount of + data filled in. + + + + + Return Code + + + 12 + + + 4 + + + This is a return code for the operation as defined in + . + + + + +
+
+
+ Error Reporting Support + If system firmware encounters an error processing requests related + to the physical adapter being virtualized by the VNIC interface, it will + generate ERROR_INDICATION commands to the VNIC client, as defined in + . The VNIC client may then, at + its discretion, obtain detailed error information using the + REQUEST_ERROR_INFO command as defined in + . It is the intent that the + VNIC client should log the detailed error information using its normal + error logging infrastructure and methods. + The REQUEST_ERROR_INFO_RSP command as defined in + is used by firmware to indicate + the successful retrieval of error information. The retrieval of detailed + error information allows firmware to reuse the resources for tracking + that error. Detailed error information can only be requested for a + specific error once. + If system firmware encounters an error while the VNIC client is not + connected, firmware will log the detailed error information using + firmware error logging methods. + Firmware will have a finite amount of space reserved for storing + detailed error information. In some situations, some detailed error + information may be unavailable in response to a REQUEST_ERROR_INFO + command if too many errors are being logged in firmware. If the detailed + error information is overwritten prior to the VNIC client performing the + relative REQUEST_ERROR_INFO command, an error return code will be + returned. + If the fatal error bit is set, the VNIC firmware has encountered a + fatal error preventing it from automatically recovering from the error. + The VNIC client should use the RAS facilities to collect any error + information, collect any RAS tracing, statistics, and possibly a dump. + Once all available error data has been collected, it is the VNIC + client’s responsibility to cause the VNIC to restart. This can be + accomplished in one of two ways: by freeing its CRQ using H_FREE_CRQ, or + by initiating a VNIC reset using the H_VIOCTL FW_RESET + subfunction. + + + ERROR_INDICATION Command + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be ERROR_INDICATION. + + + + + Flags + + + 2 + + + 1 + + + Bit 0: If this bit is 1, this is a fatal error. + Bit 1-7: These fields are reserved, and should be set to + 0. + + + + + Reserved + + + 3 + + + 1 + + + This field is reserved, and should be set to 0. + + + + + Error Identification + + + 4 + + + 4 + + + This field is set to the error identification number that + can be used to retrieve detailed information about the error + using the REQUEST_ERROR_INFO command. If this value is set to + 0, there is no more detailed error information to retrieve, and + the ERROR_INDICATION contains all relevant information. + + + + + Detailed Error Size + + + 8 + + + 4 + + + This field contains the size of the detailed error + information associated with the error. + + + + + Error Cause + + + 12 + + + 2 + + + This field contains a value as detailed in + showing the cause of + the error. + + + + + Reserved + + + 14 + + + 2 + + + This field is reserved, and should be set to 0. + + + + +
+   + + REQUEST_ERROR_INFO Command + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be REQUEST_ERROR_INFO. + + + + + Reserved + + + 2 + + + 2 + + + This field is reserved, and should be set to 0. + + + + + Buffer IOBA + + + 4 + + + 4 + + + This field contains the I/O bus address of a TCE-mapped + buffer to be used by system firmware to write the detailed + error information into. + + + + + Buffer Length + + + 8 + + + 4 + + + This field contains the length of the TCE-mapped + buffer. + + + + + Error Identification + + + 12 + + + 4 + + + This field contains the error identification from an + ERROR_INDICATION command that specifies which detailed error + information to obtain. + + + + +
+   + + REQUEST_ERROR_INFO_RSP Command + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be REQUEST_ERROR_INFO_RSP. + + + + + Reserved + + + 2 + + + 2 + + + This field is reserved, and should be set to 0. + + + + + Error Identification + + + 4 + + + 4 + + + This field contains the error identification from an + ERROR_INDICATION command. This field can be used to correlate + this response to s REQUEST_ERROR_INFO command, allowing + multiple requests for errors to be outstanding at the same + time. + + + + + Length + + + 8 + + + 4 + + + This field contains the length of data successfully + returned in the TCE-mapped buffer. + + + + + Return Code + + + 12 + + + 4 + + + This is a return code for the operation as defined in + . + + + + +
+   + + Error Cause + + + + + + + + + Value + + + + + Definition + + + + + + + + Adapter Problem + + + 0 + + + + + Bus Problem + + + 1 + + + + + Firmware Problem + + + 2 + + + + + Device Driver Problem + + + 3 + + + + + EEH Recovery + + + 4 + + + + + Firmware Updated + + + 5 + + + + + Low Memory + + + 6 + + + + + Reserved + + + 7-65535 + + + + +
+
+
+ Link State Change + This LINK_STATE_INDICATION command as defined in + is an unacknowledged command + sent by system firmware to inform the VNIC client when the state of the + link changes. The VNIC client can also use QUERY_PHYS_PARMS at any time + to poll for link state changes. + + + LINK_STATE_INDICATION Command + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be LINK_STATE_INDICATION. + + + + + Reserved + + + 2 + + + 2 + + + This field is reserved, and should be set to 0. + + + + + Physical Link State + + + 4 + + + 1 + + + If this field is a 0, the physical link is down, if the + field is a 1, the physical link is up. + + + + + Logical Link State + + + 5 + + + 1 + + + If this field is a 0, the logical link is down and the + VNIC cannot communicate with other VNICs on the same adapter, + if the field is a 1, the logical link is up, and the VNIC can + communicate with other VNICs on the same adapter. + + + + + Reserved + + + 6 + + + 10 + + + This field is reserved, and should be set to 0. + + + + +
+
+
+ Change MAC Address + The CHANGE_MAC_ADDR command defined in + allows the VNIC client to + change the current MAC address. The request to change may fail due to + Access Control List entries set up by the administrator. + + + CHANGE_MAC_ADDR and CHANGE_MAC_ADDR_RSP Commands + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be CHANGE_MAC_ADDR or + CHANGE_MAC_ADDR_RSP. + + + + + MAC Address + + + 2 + + + 6 + + + This field contains the new requested MAC address on a + CHANGE_MAC_ADDR command, and the current MAC address on a + CHANGE_MAC_ADDR_RSP. + + + + + Reserved + + + 8 + + + 4 + + + This field is reserved, and should be set to 0. + + + + + Return Code + + + 12 + + + 4 + + + This is a return code for the operation as defined in + . + + + + +
+
+
+ Multicast Support + The MULTICAST_CTRL command defined in + allows the VNIC client to + manage the reception of Multicast Ethernet traffic. Individual multicast + MAC addresses may be enabled and disabled, as well as all multicast + traffic. + The VNIC client can choose to enable more than the maximum unique + multicast Ethernet addresses as returned in the Capabilities exchange. In + the event the VNIC client does so, system firmware will either enable the + MAC address via a non-exact hashing multicast reception mechanism if the + hardware supports it, or will enable all multicast addresses. When this + is done, system firmware will report exact matches through the unique + multicast Ethernet filter via the Exact Match bit defined in the Receive + Completion Descriptor as defined in + . If the Exact Match bit is + off, and a multicast packet was returned in the Receive Completion + Descriptor, the multicast packet either matches a non-exact hashing + mechanism if one exists or system firmware has enabled all multicast MAC + address reception. + + + MULTICAST_CTRL and MULTICAST_CTRL_RSP + Commands + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be MULTICAST_CTRL or + MULTICAST_CTRL_RSP. + + + + + MAC Address + + + 2 + + + 6 + + + This field contains the new requested multicast MAC + address, as appropriate for the specific options + requested. + + + + + Flags + + + 8 + + + 1 + + + Bit 0: Enable specified multicast MAC address + Bit 1: Disable specified multicast MAC address + Bit 2: Enable the reception of all multicast MAC + addresses. This does not affect the multicast addresses enabled + through Bit 0. + Bit 3: Disable the reception of all multicast MAC + addresses. This does not affect the multicast addresses enabled + through Bit 0. + Bit 4-7: These bits are reserved, and should be set to + 0. + + + + + Reserved + + + 9 + + + 3 + + + This field is reserved, and should be set to 0. + + + + + Return Code + + + 12 + + + 4 + + + This is a return code for the operation as defined in + . + + + + +
+
+
+ VPD Support + The VPD commands may be used by the VNIC client to collect, store, + and display VPD related to the physical adapter backing the VNIC. As the + exact adapter may change during partition mobility operations, it is + suggested this data not be relied upon operationally, and be used with + the understanding that it may change from request to request. + The VPD commands are defined in + , + , + , and + . + + + GET_VPD_SIZE Command + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be GET_VPD_SIZE. + + + + + Reserved + + + 2 + + + 14 + + + This field is reserved, and should be set to 0. + + + + +
+   + + GET_VPD_SIZE_RSP Command + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be GET_VPD_SIZE_RSP. + + + + + Reserved + + + 2 + + + 2 + + + This field is reserved, and should be set to 0. + + + + + Length + + + 4 + + + 8 + + + This field contains the length of the VPD present. + + + + + Return Code + + + 12 + + + 4 + + + This is a return code for the operation as defined in + . + + + + +
+   + + GET_VPD Command + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be GET_VPD. + + + + + Reserved + + + 2 + + + 2 + + + This field is reserved, and should be set to 0. + + + + + IOBA + + + 4 + + + 4 + + + This field is an I/O bus address referring to a + TCE-mapped buffer used by system firmware to place the VNIC + VPD. + + + + + Length + + + 8 + + + 4 + + + This field contains the length of the VPD buffer. + + + + + Reserved + + + 12 + + + 4 + + + This field is reserved and should be set to 0. + + + + +
+   + + GET_VPD_RSP Command + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be GET_VPD_RSP. + + + + + Reserved + + + 2 + + + 10 + + + This field is reserved, and should be set to 0. + + + + + Return Code + + + 12 + + + 4 + + + This is a return code for the operation as defined in + . + + + + +
+
+
+ Access Control Support + The VNIC may have certain Access Control Lists (ACLs) in effect, + and some of these may change dynamically. The ACL_CHANGE_INDICATION + command defined in + is sent by system firmware to + the VNIC client in the event any of the ACLs have changed + dynamically. + The ACL_QUERY command defined in + and its associated response + defined in + may be used by the VNIC client + to obtain information about the ACLs in effect to enable earlier error + checking or ease of use functions. + + + ACL_CHANGE_INDICATION + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be ACL_CHANGE_INDICATION. + + + + + Change Type + + + 2 + + + 2 + + + If this field is a 0, the MAC address ACLs have + changed. + If this field is a 1, the VLAN id ACLs have + changed. + All other values are reserved. + + + + + Reserved + + + 4 + + + 12 + + + This field is reserved, and should be set to 0. + + + + +
+   + + ACL_QUERY + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be ACL_QUERY. + + + + + Reserved + + + 2 + + + 2 + + + This field is reserved, and should be set to 0. + + + + + IOBA + + + 4 + + + 4 + + + This field is an I/O bus address referring to a + TCE-mapped buffer used by system firmware to place the ACL + information. Upon reception of a ACL_QUERY_RSP with a Success + return code, this buffer will be filled in with the structure + as defined in + + + + + + Size + + + 8 + + + 4 + + + This field contains the size of the buffer mapped by the + IOBA. + + + + + Reserved + + + 12 + + + 4 + + + This field is reserved, and should be set to 0. + + + + +
+   + + ACL_QUERY_RSP + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be ACL_QUERY_RSP. + + + + + Reserved + + + 2 + + + 10 + + + This field is reserved, and should be set to 0. + + + + + Return Code + + + 12 + + + 4 + + + This is a return code for the operation as defined in + . + + + + +
+   + + ACL Buffer + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + Total Length + + + 0 + + + 4 + + + This field is the total length of the ACL Buffer. + + + + + Version + + + 4 + + + 4 + + + This field contains the version of ACL Buffer layout. The + initial version should be set to 1. + + + + + MAC ACLs in effect + + + 8 + + + 1 + + + This field contains a 1 if there are MAC restrictions in + effect, zero otherwise. + + + + + VLAN id ACLs in effect + + + 9 + + + 1 + + + This field contains a 1 if there are VLAN id ACLs in + effect, zero otherwise. + + + + + Reserved + + + 10 + + + 22 + + + This field is reserved, and should be set to 0. + + + + + Number of Allowed MAC addresses + + + 32 + + + 4 + + + This field contains the number of allowable MAC + addresses. + + + + + Offset to array of allowed MAC addresses + + + 36 + + + 4 + + + This field contains an offset from the start of the ACL + Buffer to an array of six byte MAC addresses. + + + + + Number of allowed VLAN ids + + + 40 + + + 4 + + + This field contains the number of allowable VLAN + ids. + + + + + Offset to array of allowed VLAN ids + + + 44 + + + 4 + + + This field contains an offset from the start of the ACL + buffer to an array of 2 byte VLAN ids. + + + + + Reserved + + + 48 + + + 80 + + + This field is reserved, and should be set to 0. + + + + + Array of allowed MAC addresses + + + variable + + + variable + + + This is the array of six byte MAC addresses, with a size + as defined in the Number of Allowed MAC address field. + + + + + Array of allowed VLAN ids + + + variable + + + variable + + + This is the array of two byte VLAN ids, with a size as + defined in the Number of Allowed VLAN ids field. + + + + +
+
+
+ Debugging Support + The TUNE command defined in + may be used by the VNIC client + to opaquely pass tuning data from the VNIC client to system firmware. As + the exact firmware backing a VNIC client may change during partition + mobility operations, it is suggested this data not be relied upon + operationally, and be used with the understanding that it may change from + adapter to adapter. + A TUNE_RSP command defined in + will be generated by system + firmware upon completion of the TUNE command. + This command is an optional VNIC command, and may not be supported + for all VNIC implementations or versions of system firmware. + + + TUNE Command + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be TUNE. + + + + + Reserved + + + 2 + + + 2 + + + This field is reserved, and should be set to 0. + + + + + IOBA + + + 4 + + + 4 + + + This field is an I/O bus address referring to a + TCE-mapped buffer used by system firmware to obtain the tuning + parameters. + + + + + Length + + + 8 + + + 4 + + + This field contains the length of the VPD buffer. + + + + + Reserved + + + 12 + + + 4 + + + This field is reserved and should be set to 0. + + + + +
+   + + TUNE_RSP Command + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + CRQ Type + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid CRQ + event. + + + + + VNIC Command + + + 1 + + + 1 + + + This field will be TUNE_RSP. + + + + + Reserved + + + 2 + + + 10 + + + This field is reserved, and should be set to 0. + + + + + Return Code + + + 12 + + + 4 + + + This is a return code for the operation as defined in + . + + + + +
+
+
+
+ Subordinate CRQ Definitions + Frame transmission and reception is handled through the Subordinate + CRQ infrastructure, using the H_SEND_SUB_CRQ and H_SEND_SUB_CRQ_INDIRECT + hypervisor calls. +
+ Frame Transmission + Since each Transmit Completion Sub-CRQ is tied to a specific + Transmit Submission Sub-CRQ, the Transmit Descriptor correlator must only + be unique for a given Transmit Completion Sub-CRQ. + Several versions of Transmit Descriptors exist. Each version has a + Descriptor Version byte at byte offset one in the descriptor, which + specifies the layout of the later thirty bytes. A sorted array is + returned in the LOGIN response specifying all versions of transmit + descriptor supported by the VNIC. The versions of the transmit descriptor + offering the best performance appear in the array first. All VNIC + versions will support Transmit Descriptor Version Zero defined in + , but that version may not + offer the best performance. + Transmit Descriptor Version Two defined in + is designed to be used in + combination with a previous use of Transmit Descriptor Version Zero or + Transmit Descriptor Version One defined in + + + + Transmit Descriptor Version Zero + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + Sub-CRQ Format + + + 0 + + + 1 + + + This value should be set to 0x80 to indicate a valid + Sub-CRQ event. + + + + + Descriptor Version + + + 1 + + + 1 + + + This field is 0 for a Version Zero Transmit + Descriptor + + + + + Flags + + + 2 + + + 1 + + + Bit 0: If set to 1, this frame should use the large send + offload feature of the physical adapter, assuming it was + previously enabled through the use of CONTROL_IP_OFFLOAD + command. + Bit 1: If set to 1, this frame should use the IP checksum + feature of the physical adapter, assuming it was previously + enabled through the use of CONTROL_IP_OFFLOAD command. + Bit 2: If set to 1, this frame should use the TCP + checksum feature of the physical adapter, assuming it was + previously enabled through the use of CONTROL_IP_OFFLOAD + command. + Bit 3: If set to 1, this frame should use the physical + adapter’s capability of inserting VLAN headers, using the + VLAN header field as the source for the values to + insert. + Bit 4:If set to 1, this frame should use the UDP checksum + feature of the physical adapter, assuming it was previously + enabled through the use of CONTROL_IP_OFFLOAD command. + Bit 5: If set to 1, this frame spans multiple transmit + descriptors. + Bit 6: If set to 1, this frame contains the last fragment + of a complete packet for transmission. + Bit 7:If set to 1, this frame requires a transmit + completion event to be posted to the VNIC client’s + Transmit Completion Sub-CRQ. If set to 0, no completion event + will be generated unless an error occurred. + + + + + IP Header offset + + + 3 + + + 1 + + + Bit 0:If set to zero, this frame contains an IPv4 frame. + If set to 1, this frames contains an IPv6 frame. + Bits 1-7: This field should be set to the offset of IP + header in the first descriptor of a chain if any checksum + offload or large send offload is enabled. + If neither checksum offload nor large send offload are + enabled, this should be set to 0. + + + + + TCP/UDP Header offset or IP Data offset + + + 4 + + + 2 + + + In the first descriptor of a chain, if any checksum + offload or large send offload function should be done for this + packet, this field must be set to the offset of the first byte + of data after the IP header and extension headers. + If no checksum offload or large send offload function + should be done for this packet, this field must be set to + 0. + + + + + VLAN Header + + + 6 + + + 2 + + + If VLAN header insertion has been enabled, this field + contains the VLAN header to be inserted if indicated in the + Flags byte. + + + + + Reserved + + + 8 + + + 1 + + + This field is reserved and should be set to 0. + + + + + MSS Size + + + 9 + + + 3 + + + If large send offload is enabled, this field contains the + MSS size. + + + + + Correlator + + + 12 + + + 4 + + + This field is set to a unique opaque value generated by + the VNIC client that allows the device driver to correlate a + transmit submission to an eventual completion. This value must + be set even if the Completion Required bit is set to 0 in the + event an error happens. + + + + + IOBA1 + + + 16 + + + 4 + + + This field contains an I/O bus address valid for the VNIC + device that refers to the first chunk of the transmit frame for + this descriptor. + + + + + Length1 + + + 20 + + + 4 + + + This contains the length of the frame fragment pointed to + by IOBA1. + + + + + IOBA2 + + + 24 + + + 4 + + + This field contains an I/O bus address valid for the VNIC + device that refers to the second fragment of the transmit frame + for this descriptor. If the corresponding length field is 0, + this field is ignored. + + + + + Length2 + + + 28 + + + 4 + + + This contains the length of the frame fragment pointed to + by IOBA2. If IOBA2 is invalid, this field should be set to + 0. + + + + +
+   + + Transmit Completion Descriptor + + + + + + + + + + + Field Name + + + + + Byte offset + + + + + Length + + + + + Definition + + + + + + + + Sub-CRQ Format + + + 0 + + + 1 + + + This value should be set to 0x80 to indicate a valid + Sub-CRQ event. + + + + + Number of Completions + + + 1 + + + 1 + + + This is the number of return code and correlator pairs of + this descriptor that are valid. It must be a value from 1 to + 5. + + + + + Return Codes + + + 2 + + + 10 + + + This is an array of 5 two byte integer return codes as + defined in + . + + + + + Correlators + + + 12 + + + 20 + + + This is an array of five four-byte correlator values as + taken from the Transmit Submission Descriptor. + + + + +
+   + + Transmit Descriptor Version One + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + Sub-CRQ Format + + + 0 + + + 1 + + + This value should be set to 0x80 to indicate a valid + Sub-CRQ event. + + + + + Descriptor Version + + + 1 + + + 1 + + + This field is 1 for a Version One Transmit + Descriptor + + + + + Flags + + + 2 + + + 1 + + + Bit 0: If set to 1, this frame should use the large send + offload feature of the physical adapter, assuming it was + previously enabled through the use of CONTROL_IP_OFFLOAD + command. + Bit 1: If set to 1, this frame should use the IP checksum + feature of the physical adapter, assuming it was previously + enabled through the use of CONTROL_IP_OFFLOAD command. + Bit 2: If set to 1, this frame should use the TCP + checksum feature of the physical adapter, assuming it was + previously enabled through the use of CONTROL_IP_OFFLOAD + command. + Bit 3: If set to 1, this frame should use the physical + adapter’s capability of inserting VLAN headers, using the + VLAN header field as the source for the values to + insert. + Bit 4:If set to 1, this frame should use the UDP checksum + feature of the physical adapter, assuming it was previously + enabled through the use of CONTROL_IP_OFFLOAD command. + Bit 5: If set to 1, this frame spans multiple transmit + descriptors. + Bit 6: If set to 1, this frame contains the last fragment + of a complete packet for transmission. + Bit 7:If set to 1, this frame requires a transmit + completion event to be posted to the VNIC client’s + Transmit Completion Sub-CRQ. If set to 0, no completion event + will be generated unless an error occurred. + + + + + IP Header offset + + + 3 + + + 1 + + + Bit 0:If set to zero, this frame contains an IPv4 frame. + If set to 1, this frames contains an IPv6 frame. + Bits 1-7: This field should be set to the offset of IP + header in the first descriptor of a chain if any checksum + offload or large send offload is enabled. + If neither checksum offload nor large send offload are + enabled, this should be set to 0. + + + + + TCP/UDP Header offset or IP Data offset + + + 4 + + + 2 + + + In the first descriptor of a chain, if any checksum + offload or large send offload function should be done for this + packet, this field must be set to the offset of the first byte + of data after the IP header and extension headers. + If no checksum offload or large send offload function + should be done for this packet, this field must be set to + 0. + + + + + VLAN Header + + + 6 + + + 2 + + + If this frame is a VLAN-tagged frame, this field contains + the VLAN tag even if it is already present in the frame, and + even if VLAN offload is disabled. If already present in the + frame, this merely provides a hint to enable fast transmission + of this frame. If the VLAN header is not present in the frame, + this field contains the VLAN header to be inserted if indicated + in the Flags byte. + + + + + Reserved + + + 8 + + + 1 + + + This field is reserved and should be set to 0. + + + + + MSS Size + + + 9 + + + 3 + + + If large send offload is enabled, this field contains the + MSS size. + + + + + Correlator + + + 12 + + + 4 + + + This field is set to a unique opaque value generated by + the VNIC client that allows the device driver to correlate a + transmit submission to an eventual completion. This value must + be set even if the Completion Required bit is set to 0 in the + event an error happens. + + + + + IOBA1 + + + 16 + + + 4 + + + This field contains an I/O bus address valid for the VNIC + device that refers to the first chunk of the transmit frame for + this descriptor. + + + + + Length1 + + + 20 + + + 4 + + + This contains the length of the frame fragment pointed to + by IOBA1. + + + + + Destination MAC address + + + 24 + + + 6 + + + This field contains the destination MAC address as + specified in the frame to be sent. The frame still must contain + this information; this merely provides a hint to enable fast + transmission of this frame. + + + + + Ethertype + + + 30 + + + 2 + + + This field contains a copy of the ethertype from the + specified frame to be sent. The frame still must contain this + information; this merely provides a hint to enable fast + transmission of this frame. + + + + +
+   + + Transmit Descriptor Version Two + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + Sub-CRQ Format + + + 0 + + + 1 + + + This value should be set to 0x80 to indicate a valid + Sub-CRQ event. + + + + + Descriptor Version + + + 1 + + + 1 + + + This field is 2 for a Version Two Transmit Descriptor. + This transmit descriptor should be used following another valid + Transmit Descriptor Format such as Version Zero or Version One. + It inherits any advanced features from the previous Transmit + Descriptor. + + + + + Flags + + + 2 + + + 1 + + + Bit 0-5: These bits are reserved, and should be set to + 0. + Bit 6: If set to 1, this frame contains the last fragment + of a complete packet for transmission. + Bit 7:If set to 1, this frame requires a transmit + completion event to be posted to the VNIC client’s + Transmit Completion Sub-CRQ. If set to 0, no completion event + will be generated unless an error occurred. + + + + + Reserved + + + 3 + + + 1 + + + This field is reserved, and should be set to 0. + + + + + IOBA1 + + + 4 + + + 4 + + + This field contains an I/O bus address valid for the VNIC + device that refers to the first chunk of the transmit frame for + this descriptor. + + + + + Length1 + + + 8 + + + 4 + + + This field contains the length of the frame fragment + pointed to by IOBA1. + + + + + Correlator + + + 12 + + + 4 + + + This field is set to a unique opaque value generated by + the VNIC client that allows the device driver to correlate a + transmit submission to an eventual completion. This value must + be set even if the Completion Required bit is set to 0 in the + event an error happens. + + + + + IOBA2 + + + 16 + + + 4 + + + This field contains an I/O bus address valid for the VNIC + device that refers to the second chunk of the transmit frame + for this descriptor. + + + + + Length2 + + + 20 + + + 4 + + + This contains the length of the frame fragment pointed to + by IOBA2. + + + + + IOBA3 + + + 24 + + + 4 + + + This field contains an I/O bus address valid for the VNIC + device that refers to the third chunk of the transmit frame for + this descriptor. + + + + + Length3 + + + 28 + + + 4 + + + This contains the length of the frame fragment pointed to + by IOBA3. + + + + +
+
+
+ Frame Reception + Multiple Receive Buffer Add Sub-CRQs can be configured to allow the + VNIC client to efficiently allocate receive buffers of different sizes. + In the event multiple Sub-CRQs are allocated for this purpose, it is the + VNIC client’s responsibility to always allocate the receive buffer + size for the Receive Buffer Add Sub-CRQs that are returned by system + firmware as defined in + . + System firmware will configure the correct buffer sizes based on + the current VNIC maximum transmission unit, current number of Receive + Buffer Add Sub-CRQs, and physical adapter capabilities. In all cases, all + receive buffers given to an individual Receive Buffer Add Sub-CRQ must be + of the same size. + Since a Receive Buffer Correlator may appear on only a single + Receive Completion Sub-CRQ, the Receive Buffer Correlators must be unique + for a given Receive Completion Sub-CRQ. + Since every buffer added to all Receive Buffer Add Sub-CRQs + associated with a given Receive Completion Sub-CRQ could be received + simultaneously, each Receive Completion Sub-CRQ should be sized to handle + every possible buffer given to system firmware on its associated Receive + Buffer Add Sub-CRQs. + Some implementations of VNIC devices may have alignment + requirements. To ensure efficient use of receive buffers, VNIC clients + are encouraged to use at least cache-line aligned receive buffers. + . + + Receive Completion Descriptor + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + Sub-CRQ Format + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid Sub-CRQ + event. + + + + + Flags + + + 1 + + + 1 + + + Bit 0: If this bit is a 1, it indicates system firmware + has validated the IP checksum field in the referenced packet + was verified to be good. + Bit 1: If this bit is a 1, it indicates system firmware + has validated the TCP/UDP checksum field in the referenced + packet was verified to be good. + Bit 2: If this bit is a 1, it indicates this frame + contains the end of a packet. + Bit 3: If this bit is a 1, this packet is an exact match + for one of the requested multicast MAC addresses for this + VNIC. + Bit 4: If this bit is a 1, the TCP/UDP checksum field + contains either the complete TCP/UDP checksum or a partial + TCP/UDP checksum in the case of an IP fragment packet. + Bit 5-7: These bits are reserved, and will be set to + 0. + + + + + Offset to start of frame data + + + 2 + + + 2 + + + This field contains an offset to the start of actual + frame data in the returned frame. + + + + + Length + + + 4 + + + 4 + + + This field contains the length of valid data in this + descriptor. + + + + + Correlator + + + 8 + + + 8 + + + This field is the correlator taken from the Receive + Buffer Add descriptor that allows the VNIC client to associate + this completion with a previously added receive buffer. + + + + + TCP/UDP Checksum + + + 16 + + + 2 + + + If the TCP/UDP checksum bit is a 1, this field contains + either the complete packet’s TCP/UDP checksum or a + partial TCP/UDP checksum in the event the packet is an IP + fragment. + + + + + Reserved + + + 18 + + + 14 + + + These fields are reserved, and will be set to 0. + + + + +
+   + + Receive Buffer Add Descriptor + + + + + + + + + + + Field Name + + + + + Byte Offset + + + + + Length + + + + + Definition + + + + + + + + Sub-CRQ Format + + + 0 + + + 1 + + + This should be set to 0x80 to indicate a valid Sub-CRQ + event. + + + + + Reserved + + + 1 + + + 7 + + + This bytes are reserved, and should be set to 0. + + + + + Correlator + + + 8 + + + 8 + + + This field is an opaque value that is returned to the + VNIC client when the buffer described by this descriptor is + used to receive a frame from the network. + + + + + IOBA + + + 16 + + + 4 + + + This field contains the I/O bus address for the + TCE-mapped memory buffer to be used for frame reception. + + + + + Length + + + 20 + + + 4 + + + This field contains the length of the memory buffer + described by this descriptor. + + + + + Reserved + + + 24 + + + 8 + + + These bytes are reserved, and should be set to 0. + + + + +
+ +
+
+ diff --git a/Virtualization/ch_virtual_scsi.xml b/Virtualization/ch_virtual_scsi.xml new file mode 100644 index 0000000..e43fc7b --- /dev/null +++ b/Virtualization/ch_virtual_scsi.xml @@ -0,0 +1,1198 @@ + + A Protocol for VSCSI Communications + +
+ Introduction + The purpose of this chapter is to define the protocol used by + virtual SCSI (vscsi) client drivers and vscsi server drivers in sufficient + detail to ensure compatibility between unlike operating systems + implementing these features. The SCSI Architecture Model (SAM-2) defines + the following simplified abstract model and terminology for a SCSI + system. + +
+ SCSI Initiator/Target Architecture + + + + + + + + +
+ In , the Application Client is the + application producing or consuming the data being stored. The SCSI + Initiator Port is the virtual scsi client adapter running in the client + partition. The Service Delivery System is the Hypervisor. The SCSI Target + Port is the vscsi host (vhost) adapter running in the VIO server (VIOS). + The Logical Unit is the entity providing the data storage + services. + Note that the model is not symmetrical. Client adapters may + communicate only with host adapters and host adapters may communicate + only with client adapters. Each may communicate with a maximum of one + partner at any point in time. Client adapters may exist only in client + partitions. Host adapters may exist only in VIOSs. A client partition may + have multiple client adapters and they may communicate with host adapters + in the same or different VIOSs. A SCSI host adapter may have multiple + Logical Units defined to it for use. Almost all messages are initiated by + the client. The client and host adapters communicate using + Command/Response Queues (CRQ) defined earlier in this document. A client + may not read or write VIOS memory, it may only write to the VIOS CRQ. The + VIOS may read and write to client partition memory, if the client passes + the VIOS a DMA mapped address for that memory. +
+
+ SCSI Remote DMA Protocol (SRP) + The protocol used for transferring data between the application + client and the logical unit is the SCSI Remote DMA Protocol (SRP), revision + 16.a, as defined by the InterNational Committee for Information Technology + Standards (INCITS). Copies of the standard are available at the INCITS + website at T10.org. + The client builds an SRP request in its address space, then DMA maps + that request so that the VIOS can access it. The client notifies the VIOS + of the request by including that mapped address in a CRQ message. A SCSI + Command Data Block (CDB) is encapsulated within the SRP request. Also + within the SRP request is a tag field, which is private to the client. The + VIOS must not modify that tag value in any way. When the request is + complete, the VIOS notifies the client of the completion by including that + tag field in the CRQ message to the client. The client then uses that tag + value to locate the request being completed. + If the SRP request expects to transfer any data, it also contains one + of the two types of memory descriptors specified by the SRP standard, to + describe the buffer(s) to be used in the data transfer. In the SRP memory + descriptor, the virtual address field is the DMA mapped address of the + buffer, to be used by the VIOS to transfer the data. The memory handle + field is not used and should be initialized to zero. + Using the H_SEND_CRQ call, the client sends the SRP request to the + VIOS. The first 64 bits of the message describe the type of message, the + format, and the length. The second 64 bits of the CRQ message contain the + DMA mapped address of the SRP request in the client partition memory. The + H_SEND_CRQ call in the client generates a virtual interrupt in the VIOS, if + the CRQ is going from empty to non-empty (edge-triggered interrupt). + The vhost driver uses the H_COPY_RDMA call and the mapped address to + copy the SRP request from client partition memory into VIOS memory, + examines the LUN to which the request is addressed, builds the appropriate + structure to represent the request, according to the type of backing + device, then queues the request to the backing device. The backing device + may be an actual physical storage device, a software emulator, or some + combination of device and emulation. + In the request is an SRP memory descriptor which contains one or more + address/length pairs describing one or more buffers in client partition + memory address space. The memory handle field of the SRP memory descriptor + is not used by vscsi and should be initialized to zero. The virtual address + field in the SRP memory descriptor is the DMA mapped address of a buffer in + client partition memory that the backing device uses to transfer data. When + the backing device services the request, it uses the same DMA services as + it would to handle a request that had originated locally on the VIOS. + However, DMA services on the VIOS use the H_COPY_RDMA call and the mapped + address(es) in the SRP memory descriptor(s) to copy data directly between + the client partition and the device, transparent to the device. + When the backing device has completed the request, it returns the + request along with the results back to the VIOS driver. The VIOS driver + builds an SRP response structure and copies that response back into client + partition memory over the original SRP request. The SRP response includes + any sense data that may have been returned with the request. All virtual + devices are “auto-sense” devices. The vhost driver then + notifies the client partition of the completed request by using H_SEND_CRQ + to place a message in the client CRQ. The first 64 bits of the message + describe the type, format, and length of the message. The second 64 bits + are the “tag” field from the original SRP request. The client + uses the tag to locate the SRP response and processes the response as + appropriate. + It is important to note that the client partition must not unmap or + modify in any way any of the memory associated with the request between the + time that it notifies the VIOS of the request and the time that the VIOS + notifies the client of the response. +
+
+ Connection Establishment + Before any data can be transferred the two partitions have to + establish a connection. Each partition is required to use H_REG_CRQ to + register a Command/Response Queue (CRQ) with the Hypervisor to receive + messages from the other partition. The size of the queue must be a multiple + of 4KB. That memory must be DMA mapped. The size of the CRQ merely + determines the number of requests that a client may send to the VIOS in a + single burst. The VIOS dequeues the requests as soon as it can, so in + evenly balanced systems, where the VIOS has enough CPUs and memory to deal + with all of its clients, the size of the CRQ is not a major limiting + factor. + After H_REG_CRQ returns H_SUCCESS, each partition uses H_SEND_CRQ to + attempt to send the Initialization message described previously in this + document. This is a race condition that only one partition will win. The + first partition to send the Initialization message receives an H_CLOSED + return value from the Hypervisor, because the other partition has not yet + registered its queue. The winning partition must wait to receive the + Initialization message from its partner. The second partition to send the + Initialization message receives an H_SUCCESS return value from the + Hypervisor. That partition must wait for the Initialization Complete + message from its partner. When a partition receives an Initialization + message during connection establishment, it must respond with the + Initialization Complete message and may then proceed to the next step. When + a partition receives the Initialization Complete message during connection + establishment, it may then proceed to the next step. + The next step in connection establishment is for the client to send + one or more of the Management Datagrams (MAD) messages, described in detail + later in this chapter. Since this is before the completion of the SRP + Login request, no flow control has been established between the client and + VIOS, so the client may send only one message at a time and must wait for + the response from the VIOS before sending the next one. The exception is + the optional MAD_EMPY_IU message. The client may follow that immediately + with another message. The VIOS enforces flow control violations by logging + and informative error, then closing and reopening the CRQ. + The client is required to send the MAD_ADAPTER_INFO_REQUEST. This + provides the information that the VIOS displays with the lsmap command. The + client may find it useful to save off and display the information that the + VIOS returns in the response to the MAD_ADAPTER_INFO_REQUEST. Customers and + service personnel frequently find this kind of information useful in + unravelling some of the more elaborate configurations. + The client is required to send the MAD_CAPABILITIES_EXCHANGE if it + wishes to participate in Partition Mobility operations. If it does not send + this message, the VIOS does not consider it to be capable of being + migrated. + If the client wishes to take advantage of the “fast fail” + feature, it should send the MAD_ENABLE_FAST_FAIL message before the SRP + login request. + The last step in connection establishment is the SRP login request. + The Target Port Identifier field of the SRP Login request is not used by + vscsi and should be initialized to zero. The client uses the SRP login + request to specify the size of the largest SRP Information Unit that it + will send to the VIOS and the format of the type of memory descriptors it + intends to use. The size of the largest SRP Information Unit must also + account for the size of the largest Management Datagram that the client + expects to send. The VIOS may reject the SRP login if it cannot support the + requested options. The VIOS will delay sending the response to the SRP + login if it does not have any LUNs defined to it yet. This may be the case + if both partitions are booted simultaneously and the VIOS has not completed + the configuration process when the client sends the SRP login. + If the VIOS accepts the SRP login, it sends the SRP login response + and notifies the client of this by placing the tag value from the SRP Login + in the CRQ message. The request limit delta field of the SRP login response + contains the maximum number of requests that the VIOS will allow the client + to have active on the VIOS at any one time. This is the flow control + mechanism. If the client violates this limit by sending too many requests, + the VIOS will terminate the connection to the client. Note that each SRP + response message also contains a request limit delta field. Typically, this + is set to 1, to indicate that this completed request means another can be + initiated. But if the VIOS has substantial resources added to it, it may + increase the number of requests a client may have active, and will do so by + setting a value greater than one in this field. Once the SRP login has been + accepted, the VIOS may increase the number of requests, but it may never + decrease that number until this connection is terminated. + After receiving an SRP Login Response for the VIOS, the client may + then proceed with normal I/O data traffic. Usually, this starts with device + discovery, where the client sends a REPORT_LUNS SCSI request to the VIOS. + The VIOS responds with the list of LUNs that have been defined to this host + adapter. The client may then use other SCSI requests to determine the + identity and capabilities of each LUN. + If, after establishing a connection (VIOS sends SRP login response, + and client receives it), a partition receives another Initialization + message, Initialization Complete message, an SRP Login, or SRP Login + response without some indication that the connection has been terminated, + usually a Transport Event (described later), that is a protocol violation. + Protocol violations are handled by logging an error, then closing and + reopening the CRQ. + Likewise, after a connection has been terminated, the first messages + must be either the Initialization or the Initialization Complete messages, + as appropriate. Any other message is a protocol violation. And any SRP + message received before a successful SRP Login is a protocol + violation. +
+
+ Connection Termination + A connection may be terminated by the client sending the VIOS an + SRP_I_LOGOUT Information Unit. The VIOS may send the client an SRP_T_LOGOUT + Information Unit, but only if the client has provided resources for this by + sending the MAD EMPTY IU first. In the current implementation, neither is + used and the drivers just call H_FREE_CRQ to terminate the + connection. + A connection may also be terminated by the abnormal termination of a + partition. When a partition crashes, the Hypervisor invalidates all of the + memory mappings for that partition and places a Transport Event in the CRQ + of the partner. If the partition that crashed was a client with requests + active on the VIOS, when the storage drivers attempt to service those + “in flight” requests, they find that the DMA mappings + associated with the requests are no longer valid and usually will log one + or more errors to that effect. + When a partition calls H_FREE_CRQ or crashes, the Hypervisor notifies + the partner partition by placing a Transport Event in the partner’s + CRQ. The first byte of the Transport Event is set to 0xFF, to indicate that + this is a Transport Event. The second byte describes the event. A value of + 0x01 indicates that the partner partition failed (crashed). A value of 0x02 + indicates that the partner partition called H_FREE_CRQ. A value of 0x06 + indicates to a client that it has been migrated. Only clients that send the + MAD_CAPABILITIES message are candidates for being migrated. A VIOS cannot + be migrated. + When a partition receives a Transport Event, it is not required to + close its CRQ. It may instead just wait for an Initialization message from + the partner partition when it is ready to communicate again. +
+
+ Client Migration + When a client receives the migrated Transport Event, it must unmap + any memory associated with any requests currently active on the VIOS. The + client will never receive any completions for those requests and must remap + and restart them at the end of the migration. Then the client must call + H_ENABLE_CRQ until it returns H_SUCCESS. When the CRQ has been successfully + enabled, the client sends the Initialization message and waits for the + Initialization Complete message. It then goes through the rest of the + connection establishment process, followed by the SRP login. After the VIOS + sends the SRP Login response, the client may resume normal data transfers, + starting with any requests that may have been active on the VIOS when the + client was migrated. + Note that the partition identification information that the client + sends in the MAD_ADAPTER_INFO message immediately after the migration event + may be stale and reflect the identification of the original client + partition before the migration. A client may register for DLPAR + notification of migration, use that notification to obtain the current + partition identification, and send another MAD_ADAPTER_INFO message to the + VIOS with the correct information. +
+
+ VSCSI Message Formats + All virtual scsi communications between client and server occurs + using the Reliable Command/Response Transport and Logical Remote DMA + functions defined earlier in this document. No other channels of + communication are required to perform virtual SCSI functions. + These communications are made up of three classes of messages: + + + + Messages contained entirely within a single CRQ message + + + + SRP requests and responses, as defined by the SRP standard + + + + Management Datagrams + + +
+
+ CRQ Message formats + CRQ messages are 16 bytes (128 bits) in length. Only the first byte + is architected by the Reliable Command/Response Transport specification + described earlier in this document. That specification is repeated in + . + + + First Byte of the CRQ Message + + + + + + + + Value + + + Description + + + + + + + 0x00 + + + Element is unused -- all other bytes in the element are + undefined + + + + + 0x01 - 0x7F + + + Reserved + + + + + 0x80 + + + Valid Command/Response Entry -- the second byte defines the + entry format + + + + + 0x81-0xFE + + + Reserved + + + + + 0xFF + + + Valid Transport Event -- the second byte defines the + specific transport event + + + + +
+ If the first byte of a CRQ message is 0x80, then it is a valid + Command/Response entry and the second byte describes the format of message. + Possible values for the second byte of the CRQ message when the first byte + is 0x80 are shown in + . + + + Second Byte of the CRQ Message + + + + + + + + Format Byte Value + + + Definition + + + + + + + 0x00 + + + Unused + + + + + 0x01 + + + VSCSI SRP format + + + + + 0x02 + + + Management Datagram (MAD) format + + + + + 0x03 + + + i5os private format + + + + + 0x04 + + + AIX private format + + + + + 0x05 + + + Linux private format + + + + + 0x06 + + + Message in CRQ format + + + + + 0x07 - 0xFF + + + Reserved + + + + +
+ If the format byte is 0x01, then the rest of the message is a vscsi + SRP request or response message. The rest of the CRQ contents for this type + of message is shown in + , for messages from the clients, + and + , for messages from the VIOS. + Messages with a format byte of 0x02 are Management Datagram messages, + defined later in this chapter. Messages formats of 0x03, 0x04, and 0x05 + are reserved for private, Operating System-specific messages, and are + currently unused by this implementation. Messages with a format byte of + 0x06 are messages contained entirely within the CRQ. +
+
+ CRQ VSCSI Client Message Format + Client messages are sent from the client partitions to the VIOS. + shows the format of these + messages, + + + CRQ VSCSI Client Message + + + + + + + + + + + + + + + Byte Offset + + + 0 + + + 1 + + + 2 + + + 3 + + + 4 + + + 5 + + + 6 + + + 7 + + + + + + + 0x00 + + + CRQ Valid + + + CRQ Format + + + Reserved + + + Timeout + + + IU Length + + + + + 0x08 + + + IU Data Pointer (TCE) + + + + +
+ For this type of message, the first byte (CRQ Valid) must be 0x80, + and the second byte (CRQ Format) must be 0x01. Bytes 6 and 7 of the first + long word are the IU Length, the length in bytes of the SRP Information + Unit being passed. The second long word, IU Data Pointer, is the DMA mapped + address of the SRP Information Unit being passed, typically an SRP Request. + The VIOS uses the IU length and IU Data Pointer to copy the SRP Request + into VIOS local memory for interpretation and processing. + Bytes 4 and 5 of the first long word, Timeout, are an optional + suggested timeout value for this request. If this value is greater than + zero, then the value may be passed along to the backing device as a + suggestion for how long this request is expected to take to complete. The + VIOS does not enforce any timeout values, but relies upon the underlaying + backing devices. + Management Datagram (MAD) messages also use this same format, with + the exception that the second byte (CRQ Format) must be set to 0x02. Bytes + 6 and 7 of the first long word are the length of the MAD message, and the + second long word, IU Data Pointer, is the DMA mapped address of the MAD + message being passed. MAD data structures are defined later in this + chapter. For MAD messages, the timeout value is not used. +
+
+ CRQ VSCSI VIOS Message Format + VIOS messages are sent from the VIOS to the clients, usually in + response to a request from the client. The VIOS message format is shown + . + + + CRQ VSCSI VIOS Message + + + + + + + + + + + + + + + Byte Offset + + + 0 + + + 1 + + + 2 + + + 3 + + + 4 + + + 5 + + + 6 + + + 7 + + + + + + + 0x00 + + + CRQ Valid + + + CRQ Format + + + Reserved + + + Status + + + Reserved + + + IU Length + + + + + 0x08 + + + IU TAG + + + + +
+ For this type of message, the first byte, CRQ Valid, must be 0x80. + This same type of message is used for SRP Responses and for responses to + MAD messages. If this is an SRP Response, the second byte, CRQ Format, is + 0x01. If this is the response to a MAD message, the second byte is 0x02. + Bytes 6 and 7 of the first long word, IU Length, contain the length of the + response. The second long word contains the tag field from the original + request. Both the SRP Request data structures and the MAD message data + structures contain a tag field for use in this message. + The Status field of the VIOS message is for reporting special, + non-SCSI status back to the client. This status is used for improving + failover times in configurations where the same storage device is visible + to this client over multiple adapters or when the same storage device is + being shared by multiple clients in clustered configurations. + If the client enables the “fast fail” feature using the + MAD_ENABLE_FAST_FAIL message, and if the VIOS determines that all paths to + a device on that client adapter have failed, the VIOS will report a status + of ADAPTER_FAILED (0x10) in response to a request to that device. + If the storage devices that the client are using are being shared by + other clients, as is the case of an IBM General Parallel File System + (GPFS™) configuration, and if the VIOS determines that all error + recovery efforts on a device have failed so that there is no point in any + more retries from the client, the VIOS will report a status of DEVICE_BUSY + (0x08) in response to a request to that device. + In both cases (ADAPTER_FAILED and DEVICE_BUSY), the client response + should be the same. The device is no longer accessible and the client + should abandon any error recovery or attempts to recover access to the + device using this client adapter. The client should attempt to failover to + another path to the device, using another adapter, if that is + possible. +
+
+ Transport Events + If the first byte (CRQ Valid) of the CRQ message is 0xFF, then this + message is a Transport Event from the Hypervisor and the connection to the + partner has been terminated. The second byte will be the reason for the + Transport Event, and may be one of the following values: + 0x01 - Partner Failed. The partner partition has crashed. + 0x02 - Partner de-registered the CRQ. The partner partition called + H_FREE_CRQ for this CRQ. This may be as a result of error recovery, as in + the case of a protocol error, or it may be the result of the system + administrator removing a client or VIOS adapter. + 0x06 - Client has been migrated as the result of a Partition Mobility + operation. Only clients can be migrated and only clients that send the + MAD_CAPABILITIES message are considered to be candidates for + migration. +
+
+ Messages in CRQs + If the first byte (CRQ Valid) of the CRQ message is 0x80, and the + second byte (CRQ Format) is 0x06, then this is a message contained entirely + within the CRQ. The rest of the message, including the IU Data Pointer, is + unused and must be initialized to zero. These messages do not require any + resources on the client or VIOS, and are not subject to flow control, so + may be sent at any time. However, they should be used sparingly, because + they do take up an entry in the CRQ and they do require interrupt + processing time to respond to them, The third byte defines the + message. + Only two messages of this type have been defined to this + point: + 0xF5 - PING + 0xF6 - PING RESPONSE + If the VIOS is not able to process interrupts, the client will likely + be hung, waiting on a completion from the VIOS. To detect this condition, + the client may send a PING to the VIOS. If the VIOS is capable of + processing an interrupt, it responds to the PING with a PING RESPONSE, + directly at interrupt level. If the client does not receive the PING + RESPONSE within a reasonably short period of time, it may choose to declare + the VIOS dead and attempt to failover to another client adapter. Likewise, + if the VIOS for some reason needs to determine if the client is still + alive, it may send a PING to the client. The client should respond as + expeditiously as possible, with a PING RESPONSE. +
+
+ VSCSI Management Datagrams (MADs) + VSCSI uses a number of messages that are not defined by the SRP + standard. The paradigm used for these messages is the Management Datagram, + discussed in the SRP and Fibre Channel specifications. Like all SRP + messages, the MADs are initiated by the client partition and the VIOS + responds to them. To initiate a MAD, the client sets the valid field to + 0x80, sets the format field to 0x02 (MAD_FORMAT), sets the length field to + the length of the data structure describing the MAD, sets the ioba field to + the mapped memory address of the data structure describing the MAD, and + uses the H_SEND_CRQ service provided by the Hypervisor to send the request + to the VIOS. + Most of these MADs can be initiated any time after the initialization + messages (INIT, INIT_COMPLETE) have been exchanged. Some of them are most + appropriately done before the SRP_login message and the start of normal + data transfer operations. These are: MAD_EMPTY_IU; + MAD_ADAPTER_INFO_REQUEST; MAD_CAPABILITIES_EXCHANGE; and + MAD_ENABLE_FAST_FAIL. Note that before the SRP_login message, resources + allocated by the VIOS for a client are limited so a client should wait for + one MAD to complete before issuing another, with the single exception of + the MAD_EMPTY_IU message. None of them are required for normal data + transfer operations between the client and VIOS. However, the + MAD_ADAPTER_INFO_REQUEST provides information that customers find highly + desirable, so using it is strongly recommended. In addition, the + MAD_ADAPTER_INFO_REQUEST returns the size of the largest data transfer + operation that the VIOS will accept from this client. Failure to honor this + limit can result in client failure. And the MAD_CAPABILITIES_EXCHANGE + message is required before a client is allowed to participate in partition + mobility operation. + The inter_op structure is used to specify the type of MAD being + sent. + + + + The type field describes the MAD and will be discussed in the + paragraphs that follow. + The status field describes the result of the MAD operation. The + client is required to initialize the status field to zero. The VIOS + responds one of three ways: + + + + MAD_NOT_SUPPORTED is returned if the VIOS is down-level. MAD_FAILED + is returned in every other situation where the MAD did not succeed. + The length field is set to the length of the data structure(s) used + in the command. + The tag field is reflected back to the client in the response to the + MAD. The VIOS uses H_SEND_CRQ to send a response with the format set to + 0x02 (MAD_FORMAT) and the ioba field is set to the tag field specified by + the client. + The type field may be set to one of the following: + + + + +
+ #define MAD_EMPTY_IU 0x01 + The client sends a MAD_EMPTY_IU command if it wishes to receive an + SRP target_logout before the VIOS closes the CRQ. The target_logout SRP + response contains the reason that the VIOS is closing the CRQ. + The MAD_EMPTY_IU command uses the following data structure: + + + + The inter_op structure is initialized with the type field set to + 0x01 (MAD_EMPTY_IU), the status field set to zero, the length field set + to the size of the mad_empty_iu structure, and the tag field set as + described above. + The desp field is set to mapped memory address of the SRP_T_LOGOUT + response data structure. The client must not unmap, free, or re-use this + memory until it receives the SRP target_logout or the CRQ is + closed. + The port field is unused at this time. +
+
+ #define MAD_ERROR_LOGGING_REQUEST 0x02 + The client sends the MAD_ERROR_LOGGING_REQUEST when it wishes the + VIOS to write an entry in the system error log on its behalf. Hardware + errors in physical storage components on the VIOS usually result in + errors on the client partition using that physical storage. The + MAD_ERROR_LOGGING REQUEST places client errors in the system error log in + proximity to the original hardware error to enable service personnel to + assess the impact of the original hardware error. + The MAD_ERROR_LOGGING_REQUEST uses the following data + structure: + + + + The inter_op structure is initialized with the type field set to + 0x02 (MAD_ERROR_LOGGING_REQUEST), the status field set to zero, the + length field set to the size of the mad_error_log structure plus the size + of the buffer of additional data, if any, and the tag field set as + described above. + The buffer field points to a mad_error_log structure. + + + + The lun field is set to the Logical Unit Number (LUN) of the device + on the client that is logging the error. + The correlator field is optional. If used, it should have a unique + value that can be used to correlate the error message on the client with + the error message on the VIOS. + The error_id field is set to a client-specific number associated + with the error. + The buffer_size is set to the length of the buffer of additional + data, which is optional. + The client_name array is set to the name by which this client + adapter instance is known on the client partition, for example + “vscsi0”. + The device_name array is set to the name by which the device + logging the error is known on the client partition, for example + “hdisk0”. + The partition field is set to the number of the client partition + requesting that the error be logged. + The flags field specifies the type of data contained in the + optional buffer. + The buffer, if used, starts immediately after the mad_error_log + structure. The buffer is not logged by the VIOS at this time. +
+
+ #define MAD_ADAPTER_INFO_REQUEST 0x03 + The client sends the MAD_ADAPTER_INFO_REQUEST to the VIOS to inform + the VIOS of the client’s identity. The VIOS responds with the + equivalent information about itself. The VIOS uses the client information + provided in the MAD_ADAPTER_INFO_REQUEST for the display in the + “lsmap” command. Use of this MAD is not enforced by VIOS. + However, customers have found the information useful enough to insist + that it be used. The MAD_ADAPTER_INFO_REQUEST may also be used after a + Partition Mobility operation to allow the client to update the + information on the VIOS, which may have changed during the + migration. + The MAD_ADAPTER_INFO_REQUEST uses the following data + structure: + + + + The inter_op structure is initialized with the type field set to + 0x03 (MAD_ADAPTER_INFO_REQUEST), the status field set to zero, the length + field set to the size of the mad_adapter_information_payload structure, + and the tag field set as described above. The buffer field points to + mapped memory address of a mad_adapter_information_payload + structure. + + + + The srp_version field is a NULL-terminated character array with the + version number of the SRP standard to which the partition complies. + Current versions of the VIOS and clients all support SRP revision 16.a. + The VIOS does not validate or enforce this field currently. + The partition name is the ASCII string representing the name of the + partition from the root node in the Open Firmware device tree. + The partition number is the integer number identifying the + partition from the root node in the Open Firmware device tree. Note that + partition number 0 is reserved for the hypervisor. + The mad_version field is set to the version of MAD messages + supported by the partition. The MAD messages described in this document + is version 1. The VIOS does not currently validate or enforce this + version. + The os_type field is set to the type of Operating System being run + on the partition. The VIOS uses this information to allocate additional + resources for client partitions that have unique requirements and to + return different values for sense data in error situations. The VIOS has + been able to make minor behavior changes to the device on behalf of + clients that use this field. + The port_max_txu array is used by the VIOS to report the size of + the largest single request that it can handle. Currently only the first + entry (port_max_txu[0]) is used. The client initializes this field to + zero. The VIOS responds with at least a value of 0x40000, meaning that it + is prepared to deal with a request to transfer at least 256,000 bytes of + data. The VIOS can respond with a larger value, depending on the + resources available and the capabilities of the physical device providing + storage. + + NOTE: If the VIOS reports a maximum transfer value + larger than the minimum of 0x40000, and subsequently a device which + cannot support that larger maximum transfer value is added to the device + inventory of this host adapter, the VIOS will log an informative error + and not report that new device in a REPORT_LUNS request until the client + has issued another MAD adapter information request. This prevents the + client from passing a data transfer request to a device which is too + large for that device to handle. The VIOS will return such requests with + an error. Optical devices typically have minimal maximum transfer + values. +
+
+ #define MAD_CAPABILITIES_EXCHANGE 0x05 + The MAD_CAPABILITIES_EXCHANGE command is used to allow the client + and VIOS to negotiate support for capabilities that may be required with + a partition migration. The data structures used are the capabilities + structure, followed by at least one specific capability structure. The + client uses a bit-mask to advertise the capabilities that it can support + by setting the bits representing those capabilities to one. The VIOS + responds by turning off (setting to zero) the bits for any capabilities + that it cannot support. This allows clients and VIOSs at a variety of + levels to cooperate in the partition migration operation. The client is + required to support a minimum level of capabilities in order to be + considered to be a candidate for migration. + The MAD_CAPABILITIES_EXCHANGE command uses the following data + structure: + + + + The inter_op field is initialized with the type field set to 0x05 + (MAD_CAPABILITIES_EXCHANGE), the status field initialized to zero, the + length field set to the size of the capabilities structures being passed, + and the tag field set as described above. The capabilities structures + must include at least the capabilities structure and the mig_cap + structure. + The buffer field contains the mapped memory address of a buffer + containing these structures. + + + + The flags field is always set to at least CAP_LIST_SUPPORTED by the + client. If the client is sending this command as the result of a + successful partition migration operation, it should also set the + CLIENT_MIGRATED flag. If the client is sending this command as the result + of a VIOS reboot or the VIOS has reset the CRQ, it should also set the + CLIENT_RECONNECT flag. If the VIOS cannot support all of the capabilities + in the list passed by the client, it will turn off the CAP_LIST_SUPPORTED + flag. If the VIOS overwrites some of the data in the capabilities list, + it will set the CAP_LIST_DATA flag. + The name array is filled with the NULL-terminated string + representing the name by which this client adapter instance is known on + the client partition, for example “vscsi0”. + The loc array is filled with the NULL-terminated string from the + “loc-code” field of the adapter node in the Open Firmware + device tree for this client adapter, for example + “U9117.MMA.107086C-V6-C5-T1”. + Following the capabilities structure is a list of capabilities to + be negotiated. Capabilities currently supported by the VIOS are + MIGRATION_CAPABILITIES and RESERVATION_CAPABILITIES. + + + + The capability_common structure is included in each capability + structure and describes the type of capability being negotiated. + The cap_type field is set to the type of capability. + MIGRATION_CAPABILITIES and RESERVATION_CAPABILITIES are the only types of + capabilities currently supported. + The length field is set to the size of the capabilities structure, + currently either mig_cap or reserve_cap. + The server_support field is initialized by the client to 1. If the + VIOS does not support that capability, it clears the field. + The capabilities structure used for negotiating migration + capabilities is as follows: + + + + The ecl field contains the effective capability level. The client + sets it to the current migration capability level that this client is + capable of supporting. If this level is lower than the level that the + VIOS can support or higher than the VIOS currently supports, the VIOS + sets the server_support to SERVER_CAP_DATA, sets the ecl field to the + lowest level it can support or the level currently supported, as + appropriate, and sets flags field of the capabilities structure to + CAP_LIST_DATA, to inform the client of the difference in the levels of + migration capabilities supported. Currently, the only migration + capability level supported is 1. + The structure used in negotiating reservation capabilities is as + follows: + + + + If the client is capable of breaking and re-establishing SCSI-2 + reservations after a migration event, it should set the type field to + CLIENT_RESERVE_SCSI_2. Otherwise, it should initialize the type field to + zero. +
+
+ #define MAD_PHYS_ADAP_INFO_REQUEST 0x06 + The MAD_PHYS_ADAP_INFO_REQUEST returns data about the physical + adapter to which the target device is attached, if the device supports + it. The only device currently supporting this request is virtual tape. + The data structure used with the MAD_PHYS_ADAP_INFO_REQUEST is as + follows: + + + + The client initializes the inter_op field, with the type set to + 0x06 (MAD_PHYS_ADAP_INFO_REQUEST), the status field initialized to zero, + the length field set to the size of the mad_phys_adapter_info structure, + the tag field set as described above, and the buffer field set to the + mapped memory address of a mad_phys_adapter_info structure. + + + + The client sets the lun field to the Logical Unit Number (LUN) of + the virtual device for which it is requesting the physical adapter + information, and it sets the version to 0x01 + (MAD_PHYS_ADAP_INFO_VERSION). + If the target device supports returning the physical adapter + information, the VIOS copies the Field Replaceable Unit (FRU) part + number, the FRU serial number, and the physical location code into the + appropriate arrays and returns that information to the client. This + information is intended for use by customer service engineers, to assist + them in repairing physical tape devices. +
+
+ #define MAD_TAPE_PASSTHROUGH_REQUEST 0x07 + The MAD_TAPE_PASSTHROUGH_REQUEST enables or disables SCSI command + data blocks (CDBs) to be passed directly to the physical tape device + driver without examination or emulation by the VIOS drivers. + The structure used with the MAD_TAPE_PASSTHROUGH_REQUEST is as + follows: + + + + The client initializes the inter_op structure by setting the type + field to 0x07 (MAD_TAPE_PASSTHROUGH_REQUEST), setting the status field to + zero, setting the length field to the size of the mad_tape_passthrough + structure, and setting the tag field as described above. The lun field is + set to the Logical Unit Number of a virtual tape device on this client + adapter. The version is set to 0x00000001 (MAD_TAPE_PASSTHRU_VERSION). + The passThru is set to either 0x00000001 (TAPE_PASSTHROUGH_ENABLE) or + 0x00000002 (TAPE_PASSTHROUGH_DISABLE). + When tape passthrough is enabled, the SCSI Command Data Blocks are + sent directly to the tape head driver, without examination or emulation + by the VIOS drivers. +
+
+ #define MAD_ENABLE_FAST_FAIL 0x08 + The MAD_ENABLE_FAST_FAIL command enables the VIOS to provide a hint + to the client that a physical device is no longer accessible so that a + failover to alternate paths, if any, should be attempted. + The only structure used with the MAD_ENABLE_FAST_FAIL command is + the inter_op structure. The type field is set to 0x08 + (MAD_ENABLE_FAST_FAIL), the status field is initialized to zero, the + length field is set to the size of the inter_op structure, and the tag + field is set as described above. + When the MAD_ENABLE_FAST_FAIL has completed successfully and the + VIOS determines that a device is no longer responding, when the VIOS is + completing an I/O request for that device back to the client, the VIOS + will set the status field in the CRQ message to 0x10 (ADAPTER_FAILED), in + addition to returning the normal device error and sense data. Fast fail + is disabled by closing the CRQ. + Two additional messages may be exchanged between clients and a VIOS + - PING and PING_RESPONSE. If a partition needs to know if the other + partition is still functional and at least able to respond to an + interrupt, it can send a PING message to the other partition. The other + partition should respond with a PING_RESPONSE. These are very lightweight + messages that require no resources. They fit entirely within the first + 64-bit quantity of the CRQ message. The PING_RESPONSE should be sent from + the interrupt code, immediately after receiving the PING. + To send a PING, the valid bit is set to one, the CRQ format field + is set to 0x06 (MESSAGE_IN_CRQ), and the status field is set to 0xF5 + (PING). + To send a PING_RESPONSE, the valid bit is set to one, the CRQ + format field is set to 0x06 (MESSAGE_IN_CRQ), and the status field is set + to 0xF6 (PING_RESPONSE). + It is strongly recommended that PING messages be used very + sparingly. One way to fill a CRQ with ping messages is to halt the VIOS + in kdb while the AIX client has requests active on it. + +
+
+ diff --git a/Virtualization/ch_virtual_tty.xml b/Virtualization/ch_virtual_tty.xml new file mode 100644 index 0000000..0e4c67e --- /dev/null +++ b/Virtualization/ch_virtual_tty.xml @@ -0,0 +1,1041 @@ + + A Protocol for a Virtual TTY Interface + +
+ Overview + This chapter defines a protocol to support partition use of a + physical serial port using a virtual TTY (VTY) interface. A protocol is + required to send control and status information of the physical device + using a data only transport. + Specifically, this protocol is used to allow the Virtual Terminal + (VTERM) option, as defined in + , as the interface to communicate + with a physical serial port which is under control of the platform instead + of the OS. + This chapter describes a connection between the platform, which has + physical control of the serial port and is an endpoint of the VTERM + interface, and a partition, which is the other endpoint of the VTERM + interface. The protocol described here provides a means to communicate both + data and control information over this data-only interface. +
+ +
+ Protocol Definition + +
+ Packet Formation + All information is sent in packets. There are four types of packets + supported for version 0, data packets, control packets, query packets and + query response packets. A packet consists of a one byte header, which + defines the type of packet, followed by a one byte length field, followed + by a two byte sequence number, followed by the packet payload, which + depends on the type of packet. This means that the minimum packet size is + 5 bytes, in the case of a one-byte data packet. + The one-byte length field for the packet is the length of the + entire packet, including the header byte and the length field + itself. + On the partition side the H_GET_TERM_CHAR and H_PUT_TERM_CHAR + hypervisor calls are used to read and write data. These HCALLS read and + write up to 16 bytes of data at once. There is no relationship between + the data in a particular HCALL and packet boundaries. A single packet can + span multiple HCALLS, and a single HCALL can contain data from more than + one packet. + For version 0, the following packet headers are defined: + +
+ Data Packet + + + + This packet type is used to send data. + The data packet is defined in + . + + + VTERM Data Packet + + + + + + + + + + Packet Offset + + + + + Member Size (Bytes) + + + + + Description + + + + + + + + 0x0 + + + 0x1 + + + Packet Header (0xFF) + + + + + 0x1 + + + 0x1 + + + Total size of packet in bytes, including this + header + + + + + 0x2 + + + 0x2 + + + Sequence Number (see description below) + + + + + 0x4 + + + variable + + + Data + + + + +
+
+ +
+ Control Packet + + + + This packet type is used to send commands that control the + operation of software or hardware on the other side of the link, and to + send notification of status changes on the other side. + The control packet is defined in + . + + + VTERM Control Packet + + + + + + + + + + Packet Offset + + + + + Member Size (Bytes) + + + + + Description + + + + + + + + 0x0 + + + 0x1 + + + Packet Header (0xFE) + + + + + 0x1 + + + 0x1 + + + Total size of packet in bytes, including this + header + + + + + 0x2 + + + 0x2 + + + Sequence Number (see description below) + + + + + 0x4 + + + 0x2 + + + Control verb (see description below) + + + + + 0x6 + + + optional and variable + + + Depending on verb, further data + + + + +
+ The following control verbs are supported. + +
+ VSV_SET_MODEM_CTL Verb (0x01) + + Protocol Version: 0x00 + + Note: One-way. This verb is only sent by the + partition to the platform. + + Data Member Definition: The data member for this verb + consists of 8 bytes, as defined in + . + + + VSV_SET_MODEM_CTL Verb Data Member + + + + + + + + + + Packet Offset + + + + + Member Size (Bytes) + + + + + Description + + + + + + + + 0x6 + + + 0x4 + + + VS_MODEM_CTL word (defined below) + + + + + 0xA + + + 0x4 + + + VS_MODEM_CTL mask, defining which bits in the control + word above are to be updated. + + + + +
+ VS_MODEM_CTL is a 4 byte bit-mask. The following bits are defined. + Note that each bit position has an associated protocol version. Note that + some bits can bet set (noted as R/W in the table), others only can be + read (noted as R/O in the table). This verb will set only bits marked + R/W. + The update of the serial port hardware driven by this command must + be serialized with data packets. + In the data portion of the packet, the first word defines the bit + values to be set; the second word is a mask defining which bits are to be + updated. See + . + + + VS_MODEM_CTL Bit Definition + + + + + + + + + + + + Bit Position + + + + + Protocol Version Supported + + + + + R/O, R/W + + + + + Name + + + + + Description + + + + + + + + 0x0000001 + + + 0x00 + + + R/W + + + TSDTR + + + Data Terminal Ready + + + + + 0x0000020 + + + 0x00 + + + R/O + + + TSCD + + + Carrier Detect + + + + +
+
+ +
+ VSV_MODEM_CTL_UPDATE Verb (0x02) + + Protocol Version: 0x00 + + Note: One-way. This verb is only sent by the platform + to the partition. + + Data Member Definition: The data member for this verb + consists of 4 bytes, as defined in + + + + VSV_MODEM_CTL_UPDATE Verb Data Member + + + + + + + + + + Packet Offset + + + + + Member Size (Bytes) + + + + + Description + + + + + + + + 0x6 + + + 0x4 + + + VS_MODEM_CTL word (defined above) + + + + +
+ This packet is sent by platform to the partition to inform the + partition of a change in status of certain bits in the VS_MODEM_CTL word. + The bits which cause this command to be sent when they transition are + defined in + . This command should be + serialized with data packets. The protocol version in + defines the first (lowest) + version of the protocol in which a transition of this bit should cause + the command to be sent. + + + VS_MODEM_CTL Word Bits + + + + + + + + + + Bit Name + + + + + Protocol Version Supported + + + + + Description + + + + + + + + TSCD + + + 0x00 + + + A transition of carrier detect must cause this packet to + be sent. + + + + +
+
+ +
+ VSV_RENEGOTIATE_CONNECTION Verb (0x03) + + Protocol Version: 0x00 + + Data Member Definition: No data member for this + verb. + This verb forces the protocol into “closed” state; see + the Connection Negotiation section below for the definition and meaning + of this state. + In normal operation it is expected that this command will be send + from the partition to the platform. However, if the platform is aware + that it will be unable to continue for some reason for a finite period of + time, it can send this command to the partition. + The platform may send this command even if the protocol is not in + an open state; this is to allow the platform to unconditionally close the + platform during an error recovery processor. + When the partition transitions control of the VTY between + independent entities, such as when it is given from OF control the to the + OS, the protocol should be closed with this command by the component that + is relinquishing it and reopened by the receiving component. +
+
+ +
+ Query Packet + + + + This packet is used to send queries to the other side of the link. + The other side responds by sending a query response packet, defined + below. There is in some case implied control of the state of the other + side of the link, as a series of queries and responses are used to + initialize (or re-initialize) the protocol. + The query packet is defined in + . + + + VTERM Query Packet + + + + + + + + + + Packet Offset + + + + + Member Size (Bytes) + + + + + Description + + + + + + + + 0x0 + + + 0x1 + + + Packet Header (0xFD) + + + + + 0x1 + + + 0x1 + + + Total size of packet in bytes, including this header + (0x6) + + + + + 0x2 + + + 0x2 + + + Sequence Number (see description below) + + + + + 0x4 + + + 0x2 + + + Query verb (see description below) + + + + +
+ The following query verbs are supported: + +
+ VSV_SEND_VERSION_NUMBER Verb (0x01) + + Protocol Version: 0x00 + + Response: The query response data member will contain + the one-byte version number of the highest version of the protocol + supported by the driver. +
+ +
+ VSV_SEND_MODEM_CTL_STATUS Verb (0x02) + + Protocol Version: 0x00 + + Response: The query response data member will contain + the four-byte VS_MODEM_CTL word defined above in the VSV_SET_MODEM_CTL + verb. + + Note: One-way. This verb is only sent by the + partition to the platform. +
+
+ +
+ Query Response Packet + + + + This packet is used to reply to query packets sent from the other + side of the link, and are sent only in response to query packets. + The query response packet is defined in + . + + + VTERM Query Response Packet + + + + + + + + + + Packet Offset + + + + + Member Size (Bytes) + + + + + Description + + + + + + + + 0x0 + + + 0x1 + + + Packet Header (0xFC) + + + + + 0x1 + + + 0x1 + + + Total size of packet in bytes, including this + header + + + + + 0x2 + + + 0x2 + + + Sequence Number (see description below) + + + + + 0x4 + + + 0x2 + + + Query verb -- matches the query verb for which this is a + response + + + + + 0x6 + + + 0x2 + + + Query Sequence Number -- the sequence number of the query + packet for which this is a response + + + + + 0x8 + + + variable + + + Verb-specific response data + + + + +
+
+
+ +
+ Verb Formation + A verb, either for a command or query packet, consists of two + bytes. The first byte is a version of the protocol associated with the + verb, and the second byte is the verb itself. This allows the flexibility + to redefine or add function to verbs in the future. More importantly, it + allows partners at either end of the protocol to find a “least + common denominator” at which they can work. + The connection sequence for partners to begin communication + (defined below) causes each side of the protocol to learn the highest + level of the protocol supported by the party on the other side. If one + party discover that the party on the other end supports a lower version + of the protocol, it is expected that only verbs at the lower version of + the protocol will be used. If an unknown verb is received, the command is + discarded without response. +
+ +
+ Sequence Numbers + Each packet has a sequence number. Sequence numbers start at 0 and + increment by one with each packet sent. There are separate name spaces + for sequence numbers in each direction, but all packets of all types in a + direction are in the same sequence number name space. The sequence number + is unsigned, and the number following 0xFFFF is 0x0. Sequence numbers are + used to match query packets with query response packets, and for general + debugging. + The sequence numbers in data packets represent a fair amount of + bandwidth overhead, especially if the number of bytes of data per packet + is small in practice. If the performance of this facility is found to be + inadequate due to bandwidth reasons, developers on both sides should + recognize that sequence numbers for data packets represents the + “low hanging fruit” to fix that problem, so are cautioned not + to create logical dependencies on sequence numbers for data packets. For + other packet types logical dependencies are acceptable, and indeed are + built into the protocol definition. + + Implementation Note: Developers should consider field + problem determination in their designs. However, other than providing + packet sequence numbers in the protocol, RAS is outside the scope of the + protocol itself. +
+ +
+ Flow Control + The partition side of the connection must understand what type or + types of flow control are supported by the platform (physical) side of + the connection. The options are no flow control, software flow control + and hardware flow control. + In version 0 of this protocol it is implied that only software flow + control is implemented by the platform side. If future platforms + implement other options, a new version of this protocol must be created + that includes a verb for the partition side to determine what type or + types of flow control are supported, and to negotiate what type is to be + used in the case that more than one is supported. +
+ +
+ Packet Type and Verb Summary + + A summary of packet types and verbs can be found in + . + + + VTERM Packet Type and Verb Summary + + + + + + + + + + Packet ID + + + + + Verb ID + + + + + Lowest Version Supported + + + + + Description + + + + + + + + 0xFF + + + -- + + + 0 + + + VS_DATA_PACKET_HEADER + + + + + 0xFE + + + -- + + + 0 + + + VS_CONTROL_PACKET_HEADER + + + + + 0xFE + + + 0x1 + + + 0 + + + VSV_SET_MODEM_CTL + + + + + 0xFE + + + 0x2 + + + 0 + + + VSV_MODEM_CTL_UPDATE + + + + + 0xFE + + + 0x3 + + + 0 + + + VSV_RENEGOTIATE_CONNECTION + + + + + 0xFE + + + 0x3 + + + 0 + + + VSV_CLOSE_PROTOCOL (alias for above) + + + + + 0xFC + + + -- + + + 0 + + + VS_QUERY_RESPONSE_PACKET_HEADER + + + + + 0xFC + + + 0x1 + + + 0 + + + VSV_SEND_VERSION_NUMBER + + + + + 0xFC + + + 0x2 + + + 0 + + + VSV_SEND_MODEM_CTL_STATUS + + + + + 0xFD + + + -- + + + 0 + + + VS_QUERY_RESPONSE_PACKET_HEADER + + + + +
+
+
+ +
+ Connection Negotiation + This protocol itself has a state of being open or closed. The state + is “closed” at partition boot time and remains closed until a + connection negotiation is initiated by the partition device driver. Once + open, the state remains “open” until a VSV_CLOSE_PROTOCOL + command is sent by either side. + While closed, both parties should “listen” on the VTY + interface. However, while closed, only query and query response packets + should be acted on; any data or control packets received should be + discarded. + The connection process is initiated by the partition side. The + sequence is as follows: + + + Both sides are in closed state. Both side are + “listening” to the VTY. + + + + The partition sends the VSV_SEND_VERSION_NUMBER query. + + + + The partition continues listening, but discard any packet that is + not a VSV_SEND_VERSION_NUMBER query response. + + + + The platform replies with the VSV_SEND_VERSION_NUMBER query + response packet. + + + + The platform clears any pending data in the serial port + hardware. + + + + The platform sends the VSV_SEND_VERSION_NUMBER query packet. + + + + The partition responds with the VSV_SEND_VERSION_NUMBER query + response packet. + + + At this point the protocol is open; any data received in the serial + hardware by the platform from this point should be put into data packets + and sent to the partition; any data packets received from the partition + should be sent out the serial hardware. + The platform should implement a time-out after sending a command that + expects a response, and after the time-out log an error. For version 0 of + the protocol an appropriate value would be seconds or minutes; at least 10 + seconds. The next version of the protocol should consider a property in the + device tree node to communicate an appropriate time-out value. + +
+ diff --git a/Virtualization/ch_vmc_comm.xml b/Virtualization/ch_vmc_comm.xml new file mode 100644 index 0000000..36cb6d5 --- /dev/null +++ b/Virtualization/ch_vmc_comm.xml @@ -0,0 +1,1301 @@ + + A Protocol for VMC Communications + +
+ Overview + The Virtual Management Channel (VMC) is a logical device which + provides an interface between the hypervisor and a management partition. + This management partition is intended to provide an alternative to + HMC-based system management. In the management partition, a Logical + Partition Manager (LPM) application exists which enables a system + administrator to configure the system’s partitioning characteristics + via a command line interface or web browser. Support for conventional HMC + management of the system may still be provided on a system; however, when + an HMC is attached to the system, the VMC interface is disabled by the + hypervisor. +
+ Logical Partition Manager + The LPM is a browser based LPAR configuration tool provided by the + management partition. System configuration, maintenance, and control + functions which traditionally require an HMC can be implemented in the + LPM using a combination of HMC to hypervisor interfaces and existing + operating system methods. This tool provides a subset of the functions + implemented by the HMC and enables basic partition configuration. The set + of HMC to hypervisor messages supported by the LPM component are passed + to the hypervisor over a VMC interface, which is defined below. The + actual content of these messages is defined in other documentation. In + order to remain consistent with this existing HMC documentation, this + chapter generally uses the HMC terminology to refer to these messages + and the LPM to hypervisor connections. +
+
+ Virtual Management Channel (VMC) + A logical device, called the virtual management channel (VMC), is + defined for communicating between the LPM application and the hypervisor. + This device, similar to a VSCSI server device, is presented to a + designated management partition as a virtual device and is only presented + when the system is not HMC managed. + This communication device borrows aspects from both VSCSI and ILLAN + devices and is implemented using the CRQ and the RDMA interfaces. The + initialization process for CRQs is defined in + , and is not duplicated here. A + three way handshake is defined that must take place to establish that + both the hypervisor and management partition sides of the channel are + running prior to sending/receiving any of the protocol messages defined + in this chapter. + Transport Event CRQs are also defined in + , and are not duplicated here. + They define the CRQ messages that are sent when the hypervisor detects + one of the peer partitions has abnormally terminated, or one side has + called H_FREE_CRQ to close their CRQ. + Two new classes of CRQ messages are introduced for the VMC device. + VMC Administrative messages are used for each partition using the VMC to + communicate capabilities to their partner. HMC Interface messages are + used for the actual flow of HMC messages between the management partition + and the hypervisor. As most HMC messages far exceed the size of a CRQ + bugger, a virtual DMA (RMDA) of the HMC message data is done prior to + each HMC Interface CRQ message. Only the management partition drives RDMA + operations; hypervisor never directly causes the movement of message + data. +
+
+
+ VMC CRQ Message Definition + For the VMC interface, all CRQ messages are defined to use the + following base format: + + + CRQ Message Base Format + + + + + + + + + 1 B + + + 1 B + + + 14 B + + + + + Header + + + Type + + + Data + + + + +
+ Two general message formats are defined: administrative and HMC + Interface. These are defined in the following sections. +
+ Administrative Messages + The administrative message format is used to configure a VMC + between the hypervisor and the management partition. The two messages + defined for this format are described in the following + subsections. + +
+ VMC Capabilities + + + VMC Capabilities Message + + + + + + + + + + + + + + + 1 B + + + 1 B + + + 1 B + + + 2 B + + + 1 B + + + 2 B + + + 4 B + + + 2 B + + + 2 B + + + + + 0x80 + + + 0x01 + + + Reserved + + + Reserved + + + # HMC’s + + + Pool Size + + + MTU + + + CRQ Size + + + Version (Major/Minor) + + + + +
+ The capabilities message is an administrative message sent after + the CRQ initialization sequence of messages and is used to exchange VMC + capabilities between the management partition and the hypervisor. The + management partition must send this message and the hypervisor must + respond with a VMC Capabilities Response message before HMC interface + messages can begin. Any HMC interface messages received before the + exchange of capabilities has completed are dropped. + This message enables the management partition and the hypervisor to + trade the following interface parameters: + + + # HMC’s. Maximum number of independent HMC connections + supported. Multiple connections would be required to support HMC pass + through mode. + + + + Pool Size. Maximum number of buffers supported per HMC + connection. + + + + MTU. Maximum message size supported (bytes). + + + + CRQ Size. Number of entries available in the CRQ for the source + partition. The target partition must limit the number of outstanding + messages to one half or less. + + + + Version. Indicates the code level of the management partition or + the hypervisor with the high-order byte indicating a major version and + the low-order byte indicating a minor version. + + +
+ +
+ VMC Capabilities Response + + + VMC Capabilities Response Message + + + + + + + + + + + + + + + 1 B + + + 1 B + + + 1 B + + + 2 B + + + 1 B + + + 2 B + + + 4 B + + + 2 B + + + 2 B + + + + + 0x80 + + + 0x81 + + + Status + + + Reserved + + + # HMC’s + + + Pool Size + + + MTU + + + CRQ Size + + + Version (Major/Minor) + + + + +
+ This command is sent by the hypervisor in response to the VMC + Capabilities message. This command enables the hypervisor to inform the + management partition of the values it supports. Parameters are identical + to the VMC Capabilities message, with the addition of the following + field: + Status. Zero is success. On failure, one of the following is + returned: + 1 - General failure + 2 - Invalid version + The hypervisor and the management partition use the minimum value + supported by each side for the parameters negotiated with the + capabilities message exchange. +
+
+ +
+ HMC Interface Buffers + Buffers are used to transfer data between the management partition + and the hypervisor. Many of the HMC Interface messages defined in + following sections indicate buffers that contain data that must be + transferred. Note the following: + + + All buffers exist in the hypervisor memory, and data is moved + between the hypervisor and the management partition by the management + partition issuing H_COPY_RDMA. + + + + To enable the management partition to access each buffer, the + hypervisor must allocate virtual TCEs as well as the actual buffer + storage. + + + + Each buffer is at least the minimum negotiated MTU bytes + long. + + + + Buffers are always owned by either the management partition or + the hypervisor. Management partition-owned buffers are used for messages + (both commands and responses) sent to the hypervisor from the management + partition. The hypervisor-owned buffers are used for messages (both + responses and asynchronous events) sent from the hypervisor to the + management partition. + + + + Each LPM interface message carrying HMC protocol (either + direction) also carries a buffer, and the ownership of this buffer + transfers from sender to receiver. + + + + There are no CRQ responses to the CRQ messages carrying HMC + protocol. The HMC protocol responses are carried in a message sent from + the other direction. + + + + The maximum depth of the buffer pool is the minimum value + negotiated via the capabilities exchange. + + + + For each of the HMC interface commands, Buffer ID is used to + identify the transfer buffer and ranges from 0 to the minimum negotiated + pool size - 1. + + + + There is a separate buffer pool for each LPM connection, each + with the negotiated number of buffers. + + +
+ +
+ HMC Interface Messages + There are several different HMC Interface messages, as defined in + the following sections. Each CRQ message has a unique HMC Interface + message type, and the HMC Interface message type defines the format for + the remaining 14 bytes of data. + +
+ Interface Open + + + Interface Open Command Message + + + + + + + + + + + + + + 1 B + + + 1 B + + + 1 B + + + 1 B + + + 1B + + + 1 B + + + 2 B + + + 8 B + + + + + 0x80 + + + 0x02 + + + Reserved + + + Reserved + + + HMC Sn + + + HMC Idx + + + Buffer ID + + + Reserved + + + + +
+ This command is sent by the management partition as the result of a + management partition device request. It causes the hypervisor to prepare + a set of data buffers for the LPM connection indicated by HMC Idx (HMC + index). A unique HMC Idx would be used if multiple management + applications running concurrently were desired. Before responding to this + command, the hypervisor must provide the management partition with at + least one of these new buffers (see the Add Buffer message defined + below). The HMC Sn (HMC Session) field is used as a session identifier + for the current VMC connection. If the management partition disconnects + (for example as the result of a crash in the LPM application), the next + open of the VMC device will result in the next HMC Sn value in the range + from 1 to 255 being used. + This message is issued after the capabilities exchange has + successfully completed and the hypervisor has issued an Add Buffer + command to create a buffer for the management partition for use in + establishing an LPM connection. The management partition sends the unique + 32-byte HMC ID to the hypervisor via an RDMA using the buffer established + by the hypervisor. +
+
+ Interface Open Response + + + Interface Open Response Message + + + + + + + + + + + + + + 1 B + + + 1 B + + + 1 B + + + 1 B + + + 1B + + + 1 B + + + 2 B + + + 8 B + + + + + 0x80 + + + 0x82 + + + Status + + + Reserved + + + HMC Sn + + + HMC Idx + + + Buffer ID + + + Reserved + + + + +
+ This command is sent by the hypervisor in response to the Interface + Open message. The status of the open command is returned in the Status + field. Zero is success. On failure, the following is returned: + 1 - General failure + When this message is received, the indicated buffer is again + available for management partition use. +
+
+ Interface Close + + + Interface Close Message + + + + + + + + + + + + + + 1 B + + + 1 B + + + 1 B + + + 1 B + + + 1B + + + 1 B + + + 2 B + + + 8 B + + + + + 0x80 + + + 0x03 + + + Reserved + + + Reserved + + + HMC Sn + + + HMC Idx + + + Reserved + + + Reserved + + + + +
+ This command is sent by the management partition to terminate an + LPM to hypervisor connection. When this command is sent, the management + partition has quiesced all I/O operations to all buffers associated with + this LPM connection, and has freed any storage for those buffers. +
+
+ Interface Close Response + + + Interface Close Response Message + + + + + + + + + + + + + + 1 B + + + 1 B + + + 1 B + + + 1 B + + + 1B + + + 1 B + + + 2 B + + + 8 B + + + + + 0x80 + + + 0x83 + + + Status + + + Reserved + + + HMC Sn + + + HMC Idx + + + Reserved + + + Reserved + + + + +
+ This command is sent by the hypervisor in response to the LPM + Interface Close message. The status of the close command is returned in + the Status field. Zero is success. On failure, the following is + returned: + 1 - General failure +
+
+ Add Buffer + + + Add Buffer Message + + + + + + + + + + + + + + 1 B + + + 1 B + + + 1 B + + + 1 B + + + 1B + + + 1 B + + + 2 B + + + 4 B + + + 4 B + + + + + 0x80 + + + 0x04 + + + Reserved + + + hypervisor + + + HMC Sn + + + HMC Idx + + + Buffer ID + + + Reserved + + + Buffer LIOBA + + + + +
+ This message transfers a buffer from hypervisor ownership to + management partition ownership. The LIOBA is obtained from the virtual + TCE table associated with the hypervisor side of the VMC device, and + points to a buffer of size MTU (as established in the capabilities + exchange). + The hypervisor field is set to 0 if the buffer being added is to be + used by the management partition for messages inbound to the hypervisor, + and to 1 if the buffer being added is to be used for messages outbound + from the hypervisor. + The typical flow for adding buffers: + + + A new LPM connection is opened by the management + partition. + + + + The hypervisor assigns new buffers for the traffic associated + with that connection. + + + + The hypervisor sends VMC Add Buffer messages to the management + partition, informing it of the new buffers. + + + + The hypervisor sends an HMC protocol message (to the LPM + application) notifying it of the new buffers. This informs the + application that it has buffers available for sending HMC + commands. + + +
+
+ Add Buffer Response + + + Add Buffer Response Message + + + + + + + + + + + + + + 1 B + + + 1 B + + + 1 B + + + 1 B + + + 1B + + + 1 B + + + 2 B + + + 8 B + + + + + 0x80 + + + 0x84 + + + Status + + + Reserved + + + HMC Sn + + + HMC Idx + + + Buffer ID + + + Reserved + + + + +
+ This command is sent by the management partition to the hypervisor + in response to the Add Buffer message. The Status field indicates the + result of the command. Zero is success. On failure, one of the following + is returned: + 1 - General failure + 2 - Invalid HMC Index + 3 - Invalid Buffer ID + 4 - HMC connection has closed +
+
+ Remove Buffer + + + Remove Buffer Message + + + + + + + + + + + + + + 1 B + + + 1 B + + + 1 B + + + 1 B + + + 1B + + + 1 B + + + 2 B + + + 8 B + + + + + 0x80 + + + 0x05 + + + Reserved + + + Reserved + + + HMC Sn + + + HMC Idx + + + Reserved + + + Reserved + + + + +
+ This message requests an HMC buffer to be transferred from + management partition ownership to hypervisor ownership. The management + partition may not be able to satisfy the request at a particular point in + time if all its buffers are in use. The management partition requires a + depth of at least one inbound buffer to allow LPM commands to flow to the + hypervisor. It is, therefore, an interface error for the hypervisor to + attempt to remove the management partition's last buffer. + The hypervisor is expected to manage buffer usage with the LPM + application directly and inform the management partition when buffers may + be removed. The typical flow for removing buffers: + + + The LPM application no longer needs a communication path to a + particular hypervisor function. That function is closed. + + + + The hypervisor and the LPM application quiesce all traffic to + that function. The hypervisor requests a reduction in buffer pool + size. + + + + The LPM application acknowledges the reduction in buffer pool + size. + + + + The hypervisor sends a Remove Buffer message to the management + partition, informing it of the reduction in buffers. + + + + The management partition verifies it can remove the buffer. This + is possible if buffers have been quiesced. + + +
+
+ Remove Buffer Response + + + Remove Buffer Response Message + + + + + + + + + + + + + 1 B + + + 1 B + + + 1 B + + + 1 B + + + 1B + + + 1 B + + + 2 B + + + 8 B + + + + + 0x80 + + + 0x85 + + + Status + + + Reserved + + + HMC Sn + + + HMC Idx + + + Buffer ID + + + Reserved + + + + +
+ This command is sent by the management partition to the hypervisor + in response to the Remove Buffer message. The Buffer ID field indicates + which buffer the management partition selected to remove. The Status + field indicates the result of the command. Zero is success. On failure, + the following is returned: + 1 - General failure + 2 - Invalid HMC Index + 3 - No buffer found +
+
+ Signal Message + + + Signal Message + + + + + + + + + + + + + + 1 B + + + 1 B + + + 1 B + + + 1 B + + + 1B + + + 1 B + + + 2 B + + + 4 B + + + 4 B + + + + + 0x80 + + + 0x06 + + + Reserved + + + Reserved + + + HMC Sn + + + HMC Idx + + + Buffer ID + + + Reserved + + + Msg Len + + + + +
+ This command is sent between the management partition and the + hypervisor in order to signal the arrival of an HMC protocol message. The + command can be sent by both the management partition and the hypervisor. + It is used for all traffic between the LPM application and the + hypervisor, regardless of who initiated the communication. + There is no response to this message. +
+
+
+ +
+ Example Management Partition VMC Driver Interface + This section provides an example for the LPM implementation where a + device driver is used to interface to the VMC device. This driver consists + of a new device, for example /dev/lparvmc, which provides interfaces to + open, close, read, write, and perform ioctl’s against the VMC + device. +
+ VMC Interface Initialization + The device driver is responsible for initializing the VMC when the + driver is loaded. It first creates and initializes the CRQ. Next, an + exchange of VMC capabilities is performed to indicate the code version + and number of resources available in both the management partition and + the hypervisor. Finally, the hypervisor requests that the management + partition create an initial pool of VMC buffers, one buffer for each + possible HMC connection, which will be used for LPM session + initialization. Prior to completion of this initialization sequence, the + device returns EBUSY to open() calls. EIO is returned for all open() + failures. + +
+ VMC Interface Initialization + + + + + + + + +
+
+
+ VMC Interface Open + After the basic VMC channel + has been initialized, an HMC session level connection can be established. + The application layer performs an open() to the VMC device and executes + an ioctl() against it, indicating the HMC ID (32 bytes of data) for this + session. If the VMC device is in an invalid state, EIO will be returned + for the ioctl(). The device driver creates a new HMC session value + (ranging from 1 to 255) and HMC index value (starting at index 0 and + potentially ranging to 254 in future releases) for this HMC ID. The + driver then does an RDMA of the HMC ID to the hypervisor, and then sends + an Interface Open message to the hypervisor to establish the session over + the VMC. After the hypervisor receives this information, it sends Add + Buffer messages to the management partition to seed an initial pool of + buffers for the new HMC connection. Finally, the hypervisor sends an + Interface Open Response message, to indicate that it is ready for normal + runtime messaging. The following illustrates this VMC flow: + +
+ VMC Interface Open + + + + + + + + +
+
+ +
+ VMC Interface Runtime + During normal runtime, the LPM + application and the hypervisor exchange HMC messages via the Signal VMC + message and RDMA operations. When sending data to the hypervisor, the LPM + application performs a write() to the VMC device, and the driver + RDMA’s the data to the hypervisor and then sends a Signal Message. + If a write() is attempted before VMC device buffers have been made + available by the hypervisor, or no buffers are currently available, EBUSY + is returned in response to the write(). A write() will return EIO for all + other errors, such as an invalid device state. When the hypervisor sends + a message to the LPM, the data is put into a VMC buffer and an Signal + Message is sent to the VMC driver in the management partition. The driver + RDMA’s the buffer into the partition and passes the data up to the + appropriate LPM application via a read() to the VMC device. The read() + request blocks if there is no buffer available to read. The LPM + application may use select() to wait for the VMC device to become ready + with data to read. + +
+ VMC Interface Runtime + + + + + + + + +
+
+
+ VMC Interface Close + HMC session level connections are + closed by the management partition when the application layer performs a + close() against the device. This action results in an Interface Close + message flowing to the hypervisor, which causes the session to be + terminated. The device driver must free any storage allocated for buffers + for this HMC connection. + +
+ VMC Interface Close + + + + + + + + +
+
+
+ diff --git a/Virtualization/figures/PAPR-18.gif b/Virtualization/figures/PAPR-18.gif new file mode 100644 index 0000000..0a077e3 Binary files /dev/null and b/Virtualization/figures/PAPR-18.gif differ diff --git a/Virtualization/figures/PAPR-19.gif b/Virtualization/figures/PAPR-19.gif new file mode 100644 index 0000000..3f3c609 Binary files /dev/null and b/Virtualization/figures/PAPR-19.gif differ diff --git a/Virtualization/figures/PAPR-20.gif b/Virtualization/figures/PAPR-20.gif new file mode 100644 index 0000000..0baec88 Binary files /dev/null and b/Virtualization/figures/PAPR-20.gif differ diff --git a/Virtualization/figures/PAPR-22.gif b/Virtualization/figures/PAPR-22.gif new file mode 100644 index 0000000..325b5cd Binary files /dev/null and b/Virtualization/figures/PAPR-22.gif differ diff --git a/Virtualization/figures/PAPR-23.gif b/Virtualization/figures/PAPR-23.gif new file mode 100644 index 0000000..a6937a1 Binary files /dev/null and b/Virtualization/figures/PAPR-23.gif differ diff --git a/Virtualization/figures/PAPR-24.gif b/Virtualization/figures/PAPR-24.gif new file mode 100644 index 0000000..ed98e0f Binary files /dev/null and b/Virtualization/figures/PAPR-24.gif differ diff --git a/Virtualization/figures/PAPR-25.gif b/Virtualization/figures/PAPR-25.gif new file mode 100644 index 0000000..f99ca2e Binary files /dev/null and b/Virtualization/figures/PAPR-25.gif differ diff --git a/Virtualization/figures/PAPR-26.gif b/Virtualization/figures/PAPR-26.gif new file mode 100644 index 0000000..94aa548 Binary files /dev/null and b/Virtualization/figures/PAPR-26.gif differ diff --git a/Virtualization/figures/PAPR-27.gif b/Virtualization/figures/PAPR-27.gif new file mode 100644 index 0000000..b551f9a Binary files /dev/null and b/Virtualization/figures/PAPR-27.gif differ diff --git a/Virtualization/figures/PAPR-28.gif b/Virtualization/figures/PAPR-28.gif new file mode 100644 index 0000000..1e372b2 Binary files /dev/null and b/Virtualization/figures/PAPR-28.gif differ diff --git a/Virtualization/figures/PAPR-29.gif b/Virtualization/figures/PAPR-29.gif new file mode 100644 index 0000000..f49ed3f Binary files /dev/null and b/Virtualization/figures/PAPR-29.gif differ diff --git a/Virtualization/figures/PAPR-29_t0_31.gif b/Virtualization/figures/PAPR-29_t0_31.gif new file mode 100644 index 0000000..f1e49df Binary files /dev/null and b/Virtualization/figures/PAPR-29_t0_31.gif differ diff --git a/Virtualization/figures/PAPR-30.gif b/Virtualization/figures/PAPR-30.gif new file mode 100644 index 0000000..701cbeb Binary files /dev/null and b/Virtualization/figures/PAPR-30.gif differ diff --git a/Virtualization/figures/PAPR-31.gif b/Virtualization/figures/PAPR-31.gif new file mode 100644 index 0000000..ee756f3 Binary files /dev/null and b/Virtualization/figures/PAPR-31.gif differ diff --git a/Virtualization/figures/PAPR-33.gif b/Virtualization/figures/PAPR-33.gif new file mode 100644 index 0000000..46ab538 Binary files /dev/null and b/Virtualization/figures/PAPR-33.gif differ diff --git a/Virtualization/figures/PAPR-55.gif b/Virtualization/figures/PAPR-55.gif new file mode 100644 index 0000000..abac8d6 Binary files /dev/null and b/Virtualization/figures/PAPR-55.gif differ diff --git a/Virtualization/figures/PAPR-58.gif b/Virtualization/figures/PAPR-58.gif new file mode 100644 index 0000000..6f1bcc0 Binary files /dev/null and b/Virtualization/figures/PAPR-58.gif differ diff --git a/Virtualization/figures/PAPR-59.gif b/Virtualization/figures/PAPR-59.gif new file mode 100644 index 0000000..e684155 Binary files /dev/null and b/Virtualization/figures/PAPR-59.gif differ diff --git a/Virtualization/figures/PAPR-66.gif b/Virtualization/figures/PAPR-66.gif new file mode 100644 index 0000000..c8d4f2c Binary files /dev/null and b/Virtualization/figures/PAPR-66.gif differ diff --git a/Virtualization/figures/PAPR-68.gif b/Virtualization/figures/PAPR-68.gif new file mode 100644 index 0000000..0e4e673 Binary files /dev/null and b/Virtualization/figures/PAPR-68.gif differ diff --git a/Virtualization/figures/PAPR-70.gif b/Virtualization/figures/PAPR-70.gif new file mode 100644 index 0000000..e8b26af Binary files /dev/null and b/Virtualization/figures/PAPR-70.gif differ diff --git a/Virtualization/figures/PAPR-71.gif b/Virtualization/figures/PAPR-71.gif new file mode 100644 index 0000000..afe7f1c Binary files /dev/null and b/Virtualization/figures/PAPR-71.gif differ diff --git a/Virtualization/figures/PAPR-72.gif b/Virtualization/figures/PAPR-72.gif new file mode 100644 index 0000000..c9a2d94 Binary files /dev/null and b/Virtualization/figures/PAPR-72.gif differ diff --git a/Virtualization/pom.xml b/Virtualization/pom.xml new file mode 100644 index 0000000..2d4eb79 --- /dev/null +++ b/Virtualization/pom.xml @@ -0,0 +1,148 @@ + + + + + org.openpowerfoundation.docs + workgroup-pom + 1.0.0-SNAPSHOT + ../pom.xml + + 4.0.0 + + + LoPAR-Virtualization + + jar + + + LoPAR-Virtualization + + + + + 0 + + + + + + + + + org.openpowerfoundation.docs + + openpowerdocs-maven-plugin + + + + generate-webhelp + + generate-webhelp + + generate-sources + + + ${comments.enabled} + LoPAR-Virtualization + 1 + UA-17511903-1 + + appendix toc,title + article/appendix nop + article toc,title + book toc,title,figure,table,example,equation + book/appendix nop + book/chapter nop + chapter toc,title + chapter/section nop + section toc + part toc,title + qandadiv toc + qandaset toc + reference toc,title + set toc,title + + + 1 + 3 + 1 + + + LoPAR_Virtualization + + + LoPAR_Virtualization + + + + workgroupSpecification + + + + + workgroupConfidential + + + + + draft + + + + + + + + + true + . + + + bk_main.xml + + + + + ${basedir}/../glossary/glossary-terms.xml + 1 + www.openpowerfoundation.org + + + + + + diff --git a/common/app_EOD.xml b/common/app_EOD.xml new file mode 100644 index 0000000..d166964 --- /dev/null +++ b/common/app_EOD.xml @@ -0,0 +1,27 @@ + + + + + End of Document + + + diff --git a/common/ch_LoPAR_preface.xml b/common/ch_LoPAR_preface.xml new file mode 100644 index 0000000..0659d63 --- /dev/null +++ b/common/ch_LoPAR_preface.xml @@ -0,0 +1,31 @@ + + + + About This Document + + + + + + + + diff --git a/common/sec_LoPAR_audience.xml b/common/sec_LoPAR_audience.xml new file mode 100644 index 0000000..c6a5a1b --- /dev/null +++ b/common/sec_LoPAR_audience.xml @@ -0,0 +1,48 @@ + + +
+ + + Audience for This Document + + This document defines the platform and system requirements for designing + LoPAR platforms. This document is the primary source of information that a platform, + OS, or hardware component developer would need to create compatible products. + Additional requirements are defined by the industry standards referenced in this + document. + + This document describes the platform to OS interface which must be provided + in these platforms. Platform designers must assemble components and firmware which + match this interface. Also, the document defines minimum system configuration + requirements. Platform designers must meet or exceed these minimums to build a + standard platform. + + This document must be used by those designing compatible software including + the OS, boot software, or firmware. If a function is supported, software developers + must provide support for the interfaces described in this document. This software + must provide the mandatory functions and capabilities as described in the requirements + in this document. However, this document does not limit this software from going beyond + the specification through software tailored to specific hardware. For example, the OS + must implement the interface to the required abstracted interfaces to hardware, but the + OS may also implement fast paths to specific hardware that it recognizes. + +
diff --git a/common/sec_LoPAR_conventions.xml b/common/sec_LoPAR_conventions.xml new file mode 100644 index 0000000..b793238 --- /dev/null +++ b/common/sec_LoPAR_conventions.xml @@ -0,0 +1,182 @@ + + +
+ + + Document-specific Conventions + + + Requirement Enumeration + Within the body of this document requirements are clearly defined by separate + paragraphs beginning with a bold text sequence number. A list of all these are + available as a separate document. These requirements may point to other standards + documents, or figures or tables which conveniently show the requirement. The + referenced material becomes part of the requirements in this document. Users of this + document must comply with these requirements to build a standard platform. Other + material in this document is supportive description of these requirements, architecture + notes, or implementation notes. Architecture or implementation notes are flagged with + a descriptive phrase—for example, “Hardware Implementation Note”— + and followed by indented paragraphs. The descriptive material and notes provide no + additional requirements and may be used for their information content. + + + + Big-Endian Numbering + Big-Endian numbering of bytes and bits is used in this document, unless + indicated otherwise. Numbering of bits starts at 0 for the most significant bit and + continues to the least significant bit, unless indicated otherwise. All data structures + used for communicating between the OS and the platform (for example, RTAS and hypervisor + calls) will be in Big-Endian format, unless otherwise designated. + + + + Hypertext Links + This document makes use of hypertext links. Cross references, Table of Contents + entries, List of Tables entries, and List of Figures entries are all clickable hypertext + links, to make navigation of the document easier. + + + + Specific Terms + In this document: + + + The term “Processor Architecture” (PA) is used to mean compliance with + the requirements specified in . + + + The term “processor” is used as a general term to mean “processor, + ” or “processor core,” or “thread of a multi-threaded processor + design.” In any case where it makes a difference, the specific terminology for that + case is used. + + + The term “real” used in relationship with addresses is a generic term + that means “processor real address” when the platform is running in SMP (non-LPAR) + mode and partition “logical real address” when the platform is running in LPAR + mode. + + + The term “PCI” is used as a general term to describe the most recent + versions of all forms of PCI standards. In cases where there are significant differences + between individual PCI standards, the following terminology is used to differentiate between + the PCI standards: conventional PCI, PCI-X, and PCI Express. + + + + + + Typographical Conventions + Typographical conventions used in this document are described in + . +   + + Typographical Conventions + + + + + Text Element + Description of Use + + + + Rn-m-x. + A requirement number. The number “n” indicates a requirement + sequence number and is changed only when it is necessary change the sequence numbers + of one or more requirements on an update. The number “m” is the section + that the requirement appears in, and the number “x” is the number of the + requirement within that section. The sequence numbers are automatically generated and + are restarted at the beginning of each new section. Sequence numbers for existing + requirements will not change unless it becomes necessary to insert a requirement between + other requirements or to add a section that renumbers other sections (at which point, + the number “n” will be incremented for the next publication of the document). + + + Italics + Used for emphasis such as the first time a new term is used. + Indicates a book title. Indicates PA instruction mnemonics. + Indicates RTAS function, field names, and parameter names + + + Courier Bold + Indicates OF properties, methods, configuration variables, node names + and encode functions (for example, encode-int and + encode-string ). In addition, OF properties are enclosed in quotes. + Indicates NVRAM partition names + + + “Courier” (not bold, enclosed in quotes) + Indicates a character string value. + + + 0xnnnn + Prefix to denote hexadecimal numbers. + + + 0bnnnn + Prefix to denote binary numbers. + + + nnnnn + Numbers without a prefix are decimal numbers. + + + 0xF... FFF100 + This hexadecimal notation represents a replication of the hexadecimal + character to the right of the ellipsis to fill out the field width. For example, the + address 0xF... FFF100 would be 0xFFFFF100 on a processor with a 32-bit address bus or + 0xFFFFFFFFFFFFF100 on a processor with a 64-bit address bus. + + + 0:9 + Ranges of bits are specified by two numbers separated by a colon. The + range includes the first number, all numbers in between, and the last number. + + + 0xm-0xn + A range of addresses or values within the document is always inclusive, + from m up to and including n. + + + <token> + This notation means the character or character string named within the + less than and greater than symbols is used in the place of the symbols and name. For + instance, the property name “ibm,sensor- <token> + ” indicates the set of properties + “ibm,sensor-9000”, + “ibm,sensor-9001” , . . . + + + Reserved For Compatibility + This notation is a placeholder used to reserve numbering (for example, + chapter, section and requirement numbers) so that subsequent numbering remains consistent + with document changes. + + + NULL vs. null + NULL designates an ASCII NULL string (0x00). The term “null” + indicates the empty set. + + + +
+ + +
diff --git a/common/sec_LoPAR_goals.xml b/common/sec_LoPAR_goals.xml new file mode 100644 index 0000000..8808489 --- /dev/null +++ b/common/sec_LoPAR_goals.xml @@ -0,0 +1,89 @@ + + +
+ + + Goals of This Specification + + The specific goals of this specification are as follows: + + + + + To provide an architecture which can be supported by converged AS/RS hardware designs. + + + + To create a stable platform architecture to be used by platforms based on processors + defined by . Processor + implementations based on this + architecture include IBM POWER8™ processors and their successors. + + + + To create an architecture which will allow platforms to operate with previous versions + of the OS (“n-1” capability). + + + + To leverage existing and future industry-standard buses and interfaces. + + + + To provide a flexible address map. Another key attribute of this specification + is the relocatability of devices and subsystems within the Processor Architecture (PA) + address space. Subsystem address information, which defines where I/O Adapters (IOAs) + reside, is detected by the OF and passed to the OS in the device tree. This architecture + accommodates the use of multiple identical buses and IOAs in the same platform without + address conflicts. + + + + To build upon the OF boot environment defined in + . + + + + To provide an architecture which can evolve as technology changes. + + + + To minimize the support cost for multiple OS versions through the definition of common + platform abstraction techniques. Common and compatible approaches to the abstraction of + hardware will reduce the burden on hardware developers who produce differentiated machines. + + + + To architect a mechanism for error handling, error reporting, and fault isolation. This + architecture provides for the implementation of more robust systems, if desired by the system + developers. + + + + To architect a mechanism for Dynamic Reconfiguration of the hardware. + + + + To provide an architecture which allows for the logical partitioning of system resources, + in order to execute multiple concurrent OS instances. + + + + +
diff --git a/common/sec_LoPAR_reading.xml b/common/sec_LoPAR_reading.xml new file mode 100644 index 0000000..b225386 --- /dev/null +++ b/common/sec_LoPAR_reading.xml @@ -0,0 +1,52 @@ + + +
+ + + Suggested Reading + + provides a full list of references and ordering information + for these references. + + This document assumes the reader has an understanding of computer architecture in general, + the Processor Architecture, the various Peripheral Component Interconnect (PCI) specifications, + and OF. Some understanding of the current personal computer and workstation architectures is also + useful. A list of suggested background reading includes: + + + + . + Note that this specification is referred to as the “Processor Architecture,” or “PA,” + in the body of this document. + + + + + + + + + + + + and relevant bindings + + + +
diff --git a/pom.xml b/pom.xml new file mode 100644 index 0000000..300f7b1 --- /dev/null +++ b/pom.xml @@ -0,0 +1,27 @@ + + + + + org.openpowerfoundation.docs + master-pom + 1.0.0-SNAPSHOT + ../Docs-Master/pom.xml + + 4.0.0 + + workgroup-pom + pom + + + + + Error Handling + RTAS + DeviceTree + Virtualization + Platform + +