Commit Graph

26 Commits (0a0fe037672d9aca82b26a86ae5d988156b6ef2f)

Author SHA1 Message Date
Paul Mackerras 5c0ba90722 decode2: Fix 32-bit flag passed to divider
Previously the 32-bit flag passed to the divider was always wrong;
this fixes it.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
5 years ago
Anton Blanchard 4016f69e70 Limit outstanding range
outstanding can only ever be -1 to 2 at the moment (0 or 1 on a
rising clock edge). Vivado is synthesizing a much wider adder
which is silly. Constrain it with a range statement. This should
be good for timing and saves us about 85 LUTs.

This will get relaxed when we add more pipelining, but only by a
few bits.

Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
5 years ago
Anton Blanchard b8fb721b81 Consolidate logical instructions
Consolidate and/andc/nand, or/orc/nor and xor/eqv, using a common
invert on the input and output. This saves us about 200 LUTs.

Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
5 years ago
Paul Mackerras f7c393ba7e Add a rotate/mask/shift unit and use it in execute1
This adds a new entity 'rotator' which contains combinatorial logic
for rotating and masking 64-bit values.  It implements the operations
of the rlwinm, rlwnm, rlwimi, rldicl, rldicr, rldic, rldimi, rldcl,
rldcr, sld, slw, srd, srw, srad, sradi, sraw and srawi instructions.
It consists of a 3-stage 64-bit rotator using 4:1 multiplexors at
each stage, two mask generators, output logic and control logic.

The insn_type_t values used for these instructions have been reduced
to just 5: OP_RLC, OP_RLCL and OP_RLCR for the rotate and mask
instructions (clear both left and right, clear left, clear right
variants), OP_SHL for left shifts, and OP_SHR for right shifts.
The control signals for the rotator are derived from the opcode
and from the is_32bit and is_signed fields of the decode_rom_t.

The rotator is instantiated as an entity in execute1 so that we can
be sure we only have one of it.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
5 years ago
Paul Mackerras 90b6e27380 Generalize the mul_32bit and mul_signed fields of decode_rom_t
This changes the names of the mul_32bit and mul_signed fields of
decode_rom_t to is_32bit and is_signed, so they can be used with
other types of operations besides multiplies.

This plumbs the is_32bit and is_signed flags down into execute1,
though they are not used at this point.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
5 years ago
Paul Mackerras 7fe84220a5 decode: Avoid multiplexing from instruction reg fields to regfile address ports
This aims to simplify the logic between the instruction image and
the register file read address ports and reduce the size of the decode
tables.  With this patch, the input_reg_a column of the decode tables
can only select RA or zeroes, the input_reg_b column can only select
RB or a constant (0, -1, or an immediate value from the instruction),
and the input_reg_c columns can only select RS or zeroes.

That means that the rotate/shift/logical ops now have their first
input coming in via the input_reg_c column.  That means we need to
add a read_data3 field to the Decode2ToExecuteType record, but that
will go away again when we split out the rotate/mask/logical ops to
their own unit.

As a related but not tightly connected change, this patch also sets
the read1_enable signal to the register file be 0 when RA=0 and the
input_reg_a for the instruction is RA_OR_ZERO (previously it was 1).

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
5 years ago
Paul Mackerras 96b402a4bf Consolidate add/subtract instructions into a single op
All of the PPC add and subtract instructions, including carrying
and extended versions, do much the same arithmetic operation:

	result = (I xor A) + B + C

where A is the value from RA, I provides a logical inversion of A
(i.e. I is 0 or -1), B is either from RB or is a constant 0 or -1,
and C is 0, 1 or the carry bit from XER (CA).

To consolidate all the add/subtract instructions into a single
OP_ADD, we add a column to decode_rom_t to indicate when A should
be inverted, and change the input_carry field to a 3-state selector
to select C in the equation above.

This also adds a new "CONST_M1" value for input_reg_b_t to indicate
that B is a constant -1.  This allows us to implement addme and
subfme.

The addex instruction appears not to exist, so the comments referring
to it are removed.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
5 years ago
Paul Mackerras 58b06eb5f3 decode: Remove const fields from decode_rom_t
The const* fields of decode_rom_t drove multiplexers in decode2 that
picked out various instruction fields and put them into the const*
fields of the Decode2ToExecute1Type record, from where they were
used in execute1.  However, the code in execute1 can just as easily
use the appropriate fields of the original instruction word, since
that is now available in execute1.  This therefore changes the
code to do that, resulting in smaller decode tables.

Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
5 years ago
Paul Mackerras c9e92483b8 decode: Push mtspr/mfspr register decoding down into execute1
Instead of doing mfctr, mflr, mftb, mtctr, mtlr as separate ops,
just pass down mfspr and mtspr ops with the spr number and let
execute1 decode which SPR we're addressing.  This will help reduce
the number of instruction bits decode1 needs to look at.

In fact we now pass down the whole instruction from decode2 to
execute1.  We will need more bits of the instruction in future,
and the tools should just optimize away any that we don't end
up using.  Since the 'aa' bit was just a copy of an instruction
bit, we can now remove it from the record.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
5 years ago
Benjamin Herrenschmidt 3e6f656a90 Add MCRF instruction
Hopefully it's not too timing catastrophic. The variable newcrf will
be handy for the other CR ops when we implement them I suspect.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
5 years ago
Benjamin Herrenschmidt 554ae88540 Implement absolute branches
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
5 years ago
Paul Mackerras 25b9450475 divider: Do absolute-value ops in divider instead of decode
This moves the negation of negative operands for signed divide and
modulus operations out of the decode2 stage and into the divider.
If either of the operands for a signed divide or modulus operation
is negative, the divider now takes an extra cycle to negate the
operands that are negative.

The interface to the divider now has an 'is_signed' signal rather
than a 'neg_result' signal, and the dividend and divisor can be
negative, so divider_tb had to be updated for the new interface.

The reason for doing this is that one of the worst timing violations
on the Arty A7-100 at 100MHz involved the carry chain in the adders
that did the negation of the dividend and divisor in the decode stage.
Moving the negations to a separate cycle fixes that and also seems to
reduce the total number of slice LUTs used.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
5 years ago
Anton Blanchard b57325ce29 Merge branch 'divider' of https://github.com/paulusmack/microwatt 5 years ago
Paul Mackerras d5bc6c8824 Add a divider unit and a testbench for it
This adds a divider unit, connected to the core in much the same way
that the multiplier unit is connected.  The division algorithm is
very simple-minded, taking 64 clock cycles for any division (even
32-bit division instructions).

The decoding is simplified by making use of regularities in the
instruction encoding for div* and mod* instructions.  Instead of
having PPC_* encodings from the first-stage decoder for each of the
different div* and mod* instructions, we now just have PPC_DIV and
PPC_MOD, and the inputs to the divider that indicate what sort of
division operation to do are derived from instruction word bits.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
5 years ago
Benjamin Herrenschmidt 98f0994698 Add core debug module
This module adds some simple core controls:

  reset, stop, start, step

along with icache clear and reading the NIA and core
status bits

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org
5 years ago
Anton Blanchard d813ffb748 Fix spurious outstanding assert
Check it in the sequential process, not the combinatorial one.

Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
5 years ago
Anton Blanchard 80aa781454
Merge pull request #47 from antonblanchard/if-fix
Explicitly check against '1' in if statements
5 years ago
Anton Blanchard b9e28598b4 Explicitly check against '1' in if statements
nvc doesn't like what I think is a VHDL 2008 construct. Lets just
check against '1' explicitly.

Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
5 years ago
Anton Blanchard 1d00c75ecc Remove nia from loadstore and multiply
Neither unit needs the NIA, so remove it.

Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
5 years ago
Anton Blanchard a8f8c54b77 Move debug execute output into decode2
This covers all units, and we avoid double printing.

Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
5 years ago
Anton Blanchard 92a7152370 Rework pipeline, add stall and flush signals
This adds stall and flush signals to the pipeline.

Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
5 years ago
Anton Blanchard a1ab1d3e56
Merge pull request #25 from antonblanchard/register_file_printing
Clean up register read debug output
5 years ago
Anton Blanchard 04eb9583e6 Clean up register read debug output
Right now we continually print all 3 possible GPRs an instruction
may be using. Add signals so we only print GPRs when they are
actually read. This should hopefully optimise away when synthesized.

Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
5 years ago
Anton Blanchard 9fbaea6f08 Rework CR file and add forwarding
Handle the CR as a single field with per nibble enables. Forward any
writes in the same cycle.

If this proves to be an issue for timing, we may want to revisit
this in the future. For now, it keeps things simple.

Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
5 years ago
Anton Blanchard 5e140298a5 Rework decode2
The decode2 stage was spaghetti code and needed cleaning up.
Create a series of functions to pull fields from a ppc instruction
and also a series of helpers to extract values for the execution
units.

As suggested by Paul, we should pass all signals to the execution
units and only set the valid signal conditionally, which should
use less resources.

Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
5 years ago
Anton Blanchard 5a29cb4699 Initial import of microwatt
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
5 years ago