Commit Graph

6 Commits (1037c6aa2e8997f47942dde1189459f910bcbd9e)

Author SHA1 Message Date
Paul Mackerras 856e9e955f core: Add framework for an FPU
This adds the skeleton of a floating-point unit and implements the
mffs and mtfsf instructions.

Execute1 sends FP instructions to the FPU and receives busy,
exception, FP interrupt and illegal interrupt signals from it.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 45cd8f4fc3 core: Add support for floating-point loads and stores
This extends the register file so it can hold FPR values, and
implements the FP loads and stores that do not require conversion
between single and double precision.

We now have the FP, FE0 and FE1 bits in MSR.  FP loads and stores
cause a FP unavailable interrupt if MSR[FP] = 0.

The FPU facilities are optional and their presence is controlled by
the HAS_FPU generic passed down from the top-level board file.  It
defaults to true for all except the A7-35 boards.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 83816cb9e3 core: Implement BCD Assist instructions addg6s, cdtbcd, cbcdtod
To avoid adding too much logic, this moves the adder used by OP_ADD
out of the case statement in execute1.vhdl so that the result can
be used by OP_ADDG6S as well.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 290b05f97d core: Implement the maddhd, maddhdu and maddld instructions
These instructions use major opcode 4 and have a third GPR input
operand, so we need a decode table for major opcode 4 and some
plumbing to get the RC register operand read.

The multiply-add instructions use the same insn_type_t values as the
regular multiply instructions, and we distinguish in execute1 by
looking at the major opcode.  This turns out to be convenient because
we don't have to add any cases in the code that handles the output of
the multiplier, and it frees up some insn_type_t values.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras fa77a6f683 core: Implement the mcrxrx instruction
This also removes OP_MCRXR, as the mcrxr instruction was removed in
version 3.0B of the Power ISA, having been phased-out for the server
architecture since v2.02.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 49a4d9f67a Add core logging
This logs 256 bits of data per cycle to a ring buffer in BRAM.  The
data collected can be read out through 2 new SPRs or through the
debug interface.

The new SPRs are LOG_ADDR (724) and LOG_DATA (725).  LOG_ADDR contains
the buffer write pointer in the upper 32 bits (in units of entries,
i.e. 32 bytes) and the read pointer in the lower 32 bits (in units of
doublewords, i.e. 8 bytes).  Reading LOG_DATA gives the doubleword
from the buffer at the read pointer and increments the read pointer.
Setting bit 31 of LOG_ADDR inhibits the trace log system from writing
to the log buffer, so the contents are stable and can be read.

There are two new debug addresses which function similarly to the
LOG_ADDR and LOG_DATA SPRs.  The log is frozen while either or both of
the LOG_ADDR SPR bit 31 or the debug LOG_ADDR register bit 31 are set.

The buffer defaults to 2048 entries, i.e. 64kB.  The size is set by
the LOG_LENGTH generic on the core_debug module.  Software can
determine the length of the buffer because the length is ORed into the
buffer write pointer in the upper 32 bits of LOG_ADDR.  Hence the
length of the buffer can be calculated as 1 << (31 - clz(LOG_ADDR)).

There is a program to format the log entries in a somewhat readable
fashion in scripts/fmt_log/fmt_log.c.  The log_entry struct in that
file describes the layout of the bits in the log entries.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago