These were missed earlier when the single-issue flag was turned off on
the other loads and stores by commit 1a244d3470 ("Remove single-issue
constraint for most loads and stores").
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
We don't run these but we should.
The SOC tests have bit rotted. We need to fix them but leave them out
for now.
Signed-off-by: Michael Neuling <mikey@neuling.org>
This increases the number of L2 lines from 32 to 64. The BRAM usage is the
same as they were only half used. There's an increase in LUTs and registers
due to the extra tags and valid bits, but none of it should be in a
space constrained or critical timing path.
We could make it wider instead (256 bytes lines) which would reduce usage
instead, but this increases the latency by 8 cycles. Something to consider
once the L2 is capable of early response on miss and starting reloads
from any point in a line.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
By adding logic to decode2 to be able to send the instruction address
down the A input, and making CONST_DX_HI (renamed to CONST_DXHI4) add
4 to the immediate value (easy since the bottom 16 bits were zero),
we can do addpcis using the main adder. This reduces the width of the
result mux and frees up one value in insn_type_t, since we can now use
OP_ADD for addpcis.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Support for this has bitrotted and would require refactoring of L2 to
be brought back. It's also not really needed anymore now that we ship
pre-generated litedram and that LiteX supports what we do.
So take it out, which simplifies some of the scripts as well. This also
fixes up CSR alignment the sim model.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The test bench test simple access forms for now, it's a starting point
but it already helped find/fix a bug.
Includes a litedram update to be able to operate the sim model without
inits.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds a cache between the wishbone and litedram with the following
features (at this point, it's still evolving)
- 128 bytes line width in order to have a reasonable amount of
litedram pipelining on the 128-bit wide data port.
- Configurable geometry otherwise
- Stores are acked immediately on wishbone whether hit or miss
(minus a 2 cycles delay if there's a previous load response in the
way) and sent to LiteDRAM via 8 entries (configurable) store queue
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds an option to disable the main BRAM and instead copy a
payload stashed along with the init code in the secondary BRAM
into DRAM and boot from there
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds a simulated litedram model along with the necessary
Makefile gunk to verilate it and wrap it for use by ghdl.
The core_dram_tb test bench is a variant of core_tb with
LiteDRAM simulated. It's not built by default, an explicit
make core_dram_tb
is necessary as to not require verilator to be installed for
the normal build process (also it's slow'ish).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
By default openocd tries to "guess" the file type and interpret
it accordingly. For example it will detect an ELF file based on
the presence of an ELF header and will try to load the relevant
segments into the flash.
This may not be what we want. For example, I want to load the raw
ELF file into the flash.
Additionally the ELF parser in most distro's OpenOCD version
only supports ELF32 and will error out.
This adds a "-t" argument to flash-arty to allow us to specify the
file format. For example "-t bin" will treat the file as raw binary.
Unfortunately I had to copy and modify jtagspi.cfg from OpenOCD
to achieve this.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The global wr_en signal is causing Vivado to generate two TDP (True Dual Port)
block RAMs instead of one SDP (Simple Dual Port) for each cache way. Remove
it and instead apply a AND to the individual byte write enables.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The two tests obtain NIA with bl+mflr+addi and then compare it
against addpcis with the minimum and maximum immediate operand values.
They were also tested on a real POWER9 system (in userspace) for good
measure.
Signed-off-by: Shawn Anastasio <shawn@anastas.io>
This commit adds support for the addpcis instruction from ISA 3.0.
A new input_reg_b_t type, CONST_DX_HI, was added to support the
shifted immediate value used in DX-Form instructions.
Signed-off-by: Shawn Anastasio <shawn@anastas.io>
Use a simple wire. common.vhdl types are better kept for things
local to the core. We can add more wires later if we need to for
HV irqs etc...
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This changes the SoC interconnect such that the main 64-bit wishbone out
of the processor is first split between only 3 slaves (BRAM, DRAM and a
general "IO" bus) instead of all the slaves in the SoC.
The IO bus leg is then latched and down-converted to 32 bits data width,
before going through a second address decoder for the various IO devices.
This significantly reduces routing and timing pressure on the main bus,
allowing to get rid of frequent timing violations when synthetizing on
small'ish FPGAs such as the Artix-7 35T found on the original Arty board.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We still need to a way to our FPGA target on the command line, but this
at least gets us down to a common Makefile.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
Instead of building each file one by one (and having to track all
the dependencies manually), use the ghdl -c command that does
analysis and elaboration in one go.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
Add a microwatt-verilator target that simulates the
ghdl -> yosys -> verilog -> verilator path. A good test of
ghdl/yosys synthesis.
Because the everything is run through synthesis, the instruction
image is baked into the build via the RAM_INIT_FILE generic.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
This describes how to build the tool on Fedora, and on Debian which lacks a packaged
liburjtag as of mid 2020.
Signed-off-by: Joel Stanley <joel@jms.id.au>
CFLAGS was defined but not used anywhere. This adds them to the compile
line, and fixes the warnings (and errors!) that result.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Paul Mackerras
Michael Neuling
Benjamin Herrenschmidt