This compares the address being fetched with the contents of a
register that can be set via DMI, and if they match, stops the
logging. Since this works on the address being fetched rather than
executed, it is subject to false positives.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This plumbs the LOG_LENGTH parameter (which controls how many entries
the core log RAM has) up to the top level so that it can be set on
the fusesoc command line and have different default values on
different FPGAs.
It now defaults to 512 entries generally and on the Artix-7 35 parts,
and 2048 on the larger Artix-7 FPGAs. It can be set to 0 if desired.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This logs 256 bits of data per cycle to a ring buffer in BRAM. The
data collected can be read out through 2 new SPRs or through the
debug interface.
The new SPRs are LOG_ADDR (724) and LOG_DATA (725). LOG_ADDR contains
the buffer write pointer in the upper 32 bits (in units of entries,
i.e. 32 bytes) and the read pointer in the lower 32 bits (in units of
doublewords, i.e. 8 bytes). Reading LOG_DATA gives the doubleword
from the buffer at the read pointer and increments the read pointer.
Setting bit 31 of LOG_ADDR inhibits the trace log system from writing
to the log buffer, so the contents are stable and can be read.
There are two new debug addresses which function similarly to the
LOG_ADDR and LOG_DATA SPRs. The log is frozen while either or both of
the LOG_ADDR SPR bit 31 or the debug LOG_ADDR register bit 31 are set.
The buffer defaults to 2048 entries, i.e. 64kB. The size is set by
the LOG_LENGTH generic on the core_debug module. Software can
determine the length of the buffer because the length is ORed into the
buffer write pointer in the upper 32 bits of LOG_ADDR. Hence the
length of the buffer can be calculated as 1 << (31 - clz(LOG_ADDR)).
There is a program to format the log entries in a somewhat readable
fashion in scripts/fmt_log/fmt_log.c. The log_entry struct in that
file describes the layout of the bits in the log entries.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This provides commands on the debug interface to read the value of
the MSR or any of the 64 GSPR register file entries. The GSPR values
are read using the B port of the register file in a cycle when
decode2 is not using it.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The goal is to have the icache fit in BRAM by latching the output
into a register. In order to avoid timing issues , we need to give
the BRAM a full cycle on reads, and thus we souce the BRAM address
directly from fetch1 latched NIA.
(Note: This will be problematic if/when we want to hash the address,
we'll probably be better off having fetch1 latch a fully hashed address
along with the normal one, so the icache can use the former to address
the BRAM and pass the latter along)
One difficulty is that we cannot really stall the icache without adding
more combo logic that would break the "one full cycle" BRAM model. This
means that on stalls from decode, by the time we stall fetch1, it has
already gone to the next address, which the icache is already latching.
We work around this by having a "stash" buffer in fetch2 that will stash
away the icache output on a stall, and override the output of the icache
with the content of the stash buffer when unstalling.
This requires a rewrite of the stop/step debug logic as well. We now
do most of the hard work in fetch1 which makes more sense.
Note: Vivado is still not inferring an built-in output register for the
BRAMs. I don't want to add another cycle... I don't fully understand why
it wouldn't be able to treat current_row as such but clearly it won't. At
least the timing seems good enough now for 100Mhz, possibly more.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This module adds some simple core controls:
reset, stop, start, step
along with icache clear and reading the NIA and core
status bits
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org
Paul Mackerras
Benjamin Herrenschmidt