forked from cores/microwatt
You cannot select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
395 lines
12 KiB
VHDL
395 lines
12 KiB
VHDL
library ieee;
|
|
use ieee.std_logic_1164.all;
|
|
use ieee.numeric_std.all;
|
|
|
|
library work;
|
|
use work.wishbone_types.all;
|
|
|
|
entity spi_rxtx is
|
|
generic (
|
|
DATA_LINES : positive := 1; -- Number of data lines
|
|
-- 1=MISO/MOSI, otherwise 2 or 4
|
|
INPUT_DELAY : natural range 0 to 1 := 1 -- Delay latching of SPI input:
|
|
-- 0=no delay, 1=clk/2
|
|
);
|
|
port (
|
|
clk : in std_ulogic;
|
|
rst : in std_ulogic;
|
|
|
|
--
|
|
-- Clock divider
|
|
-- SCK = CLK/((CLK_DIV+1)*2) : 0=CLK/2, 1=CLK/4, 2=CLK/6....
|
|
--
|
|
-- This need to be changed before a command.
|
|
-- XX TODO add handshake
|
|
clk_div_i : in natural range 0 to 255;
|
|
|
|
--
|
|
-- Command port (includes write data)
|
|
--
|
|
|
|
-- Valid & ready: command sampled when valid=1 and ready=1
|
|
cmd_valid_i : in std_ulogic;
|
|
cmd_ready_o : out std_ulogic;
|
|
|
|
-- Command modes:
|
|
-- 000 : Single bit read+write
|
|
-- 010 : Single bit read
|
|
-- 011 : Single bit write
|
|
-- 100 : Dual read
|
|
-- 101 : Dual write
|
|
-- 110 : Quad read
|
|
-- 111 : Quad write
|
|
cmd_mode_i : in std_ulogic_vector(2 downto 0);
|
|
|
|
-- # clocks-1 in a command (#bits-1)
|
|
cmd_clks_i : in std_ulogic_vector(2 downto 0);
|
|
|
|
-- Write data (sampled with command)
|
|
cmd_txd_i : in std_ulogic_vector(7 downto 0);
|
|
|
|
--
|
|
-- Read data port. Data valid when d_ack=1, no ready
|
|
-- signal, receiver must be ready
|
|
--
|
|
d_rxd_o : out std_ulogic_vector(7 downto 0);
|
|
d_ack_o : out std_ulogic := '0';
|
|
|
|
-- Set when all commands are done. Needed for callers to know when
|
|
-- to release CS#
|
|
bus_idle_o : out std_ulogic;
|
|
|
|
--
|
|
-- SPI port. These might need to go into special IOBUFs or STARTUPE2 on
|
|
-- Xilinx.
|
|
--
|
|
-- Data lines are organized as follow:
|
|
--
|
|
-- DATA_LINES = 1
|
|
--
|
|
-- sdat_o(0) is MOSI (master output slave input)
|
|
-- sdat_i(0) is MISO (master input slave output)
|
|
--
|
|
-- DATA_LINES > 1
|
|
--
|
|
-- sdat_o(0..n) are DQ(0..n)
|
|
-- sdat_i(0..n) are DQ(0..n)
|
|
--
|
|
-- as such, beware that:
|
|
--
|
|
-- sdat_o(0) is MOSI (master output slave input)
|
|
-- sdat_i(1) is MISO (master input slave output)
|
|
--
|
|
-- In order to leave dealing with the details of how to wire the tristate
|
|
-- and bidirectional pins to the system specific toplevel, we separate
|
|
-- the input and output signals, and provide a "sdat_oe" signal which
|
|
-- is the "output enable" of each line.
|
|
--
|
|
sck : out std_ulogic;
|
|
sdat_o : out std_ulogic_vector(DATA_LINES-1 downto 0);
|
|
sdat_oe : out std_ulogic_vector(DATA_LINES-1 downto 0);
|
|
sdat_i : in std_ulogic_vector(DATA_LINES-1 downto 0)
|
|
);
|
|
end entity spi_rxtx;
|
|
|
|
architecture rtl of spi_rxtx is
|
|
|
|
-- Internal clock signal. Output is gated by sck_en_int
|
|
signal sck_0 : std_ulogic;
|
|
signal sck_1 : std_ulogic;
|
|
|
|
-- Clock divider latch
|
|
signal clk_div : natural range 0 to 255;
|
|
|
|
-- 1 clk pulses indicating when to send and when to latch
|
|
--
|
|
-- Typically for CPOL=CPHA
|
|
-- sck_send is sck falling edge
|
|
-- sck_recv is sck rising edge
|
|
--
|
|
-- Those pulses are generated "ahead" of the corresponding
|
|
-- edge so then are "seen" at the rising sysclk edge matching
|
|
-- the corresponding sck edgeg.
|
|
signal sck_send : std_ulogic;
|
|
signal sck_recv : std_ulogic;
|
|
|
|
-- Command mode latch
|
|
signal cmd_mode : std_ulogic_vector(2 downto 0);
|
|
|
|
-- Output shift register (use fifo ?)
|
|
signal oreg : std_ulogic_vector(7 downto 0);
|
|
|
|
-- Input latch
|
|
signal dat_i_l : std_ulogic_vector(DATA_LINES-1 downto 0);
|
|
|
|
-- Data ack latch
|
|
signal dat_ack_l : std_ulogic;
|
|
|
|
-- Delayed recv signal for the read machine
|
|
signal sck_recv_d : std_ulogic;
|
|
|
|
-- Input shift register (use fifo ?)
|
|
signal ireg : std_ulogic_vector(7 downto 0);
|
|
|
|
-- Bit counter
|
|
signal bit_count : std_ulogic_vector(2 downto 0);
|
|
|
|
-- Next/start/stop command signals. Set when counter goes negative
|
|
signal next_cmd : std_ulogic;
|
|
signal start_cmd : std_ulogic;
|
|
signal end_cmd : std_ulogic;
|
|
|
|
function data_single(mode : std_ulogic_vector(2 downto 0)) return boolean is
|
|
begin
|
|
return mode(2) = '0';
|
|
end;
|
|
function data_dual(mode : std_ulogic_vector(2 downto 0)) return boolean is
|
|
begin
|
|
return mode(2 downto 1) = "10";
|
|
end;
|
|
function data_quad(mode : std_ulogic_vector(2 downto 0)) return boolean is
|
|
begin
|
|
return mode(2 downto 1) = "11";
|
|
end;
|
|
function data_write(mode : std_ulogic_vector(2 downto 0)) return boolean is
|
|
begin
|
|
return mode(0) = '1';
|
|
end;
|
|
|
|
type state_t is (STANDBY, DATA);
|
|
signal state : state_t;
|
|
begin
|
|
|
|
-- We don't support multiple data lines at this point
|
|
assert DATA_LINES = 1 or DATA_LINES = 2 or DATA_LINES = 4
|
|
report "Unsupported DATA_LINES configuration !" severity failure;
|
|
|
|
-- Clock generation
|
|
--
|
|
-- XX HARD WIRE CPOL=1 CPHA=1 for now
|
|
sck_gen: process(clk)
|
|
variable counter : integer range 0 to 255;
|
|
begin
|
|
if rising_edge(clk) then
|
|
if rst = '1' then
|
|
sck_0 <= '1';
|
|
sck_1 <= '1';
|
|
sck_send <= '0';
|
|
sck_recv <= '0';
|
|
clk_div <= 0;
|
|
counter := 0;
|
|
elsif counter = clk_div then
|
|
counter := 0;
|
|
|
|
-- Latch new divider
|
|
clk_div <= clk_div_i;
|
|
|
|
-- Internal version of the clock
|
|
sck_0 <= not sck_0;
|
|
|
|
-- Generate send/receive pulses to run out state machine
|
|
sck_recv <= not sck_0;
|
|
sck_send <= sck_0;
|
|
else
|
|
counter := counter + 1;
|
|
sck_recv <= '0';
|
|
sck_send <= '0';
|
|
end if;
|
|
|
|
-- Delayed version of the clock to line up with
|
|
-- the up/down signals
|
|
--
|
|
-- XXX Figure out a better way
|
|
if (state = DATA and end_cmd = '0') or (next_cmd = '1' and cmd_valid_i = '1') then
|
|
sck_1 <= sck_0;
|
|
else
|
|
sck_1 <= '1';
|
|
end if;
|
|
end if;
|
|
end process;
|
|
|
|
-- SPI clock
|
|
sck <= sck_1;
|
|
|
|
-- Ready to start the next command. This is set on the clock down
|
|
-- after the counter goes negative.
|
|
-- Note: in addition to latching a new command, this will cause
|
|
-- the counter to be reloaded.
|
|
next_cmd <= '1' when sck_send = '1' and bit_count = "111" else '0';
|
|
|
|
-- We start a command when we have a valid request at that time.
|
|
start_cmd <= next_cmd and cmd_valid_i;
|
|
|
|
-- We end commands if we get start_cmd and there's nothing to
|
|
-- start. This sends up to standby holding CLK high
|
|
end_cmd <= next_cmd and not cmd_valid_i;
|
|
|
|
-- Generate cmd_ready. It will go up and down with sck, we could
|
|
-- gate it with cmd_valid to make it look cleaner but that would
|
|
-- add yet another combinational loop on the wishbone that I'm
|
|
-- to avoid.
|
|
cmd_ready_o <= next_cmd;
|
|
|
|
-- Generate bus_idle_o
|
|
bus_idle_o <= '1' when state = STANDBY else '0';
|
|
|
|
-- Main state machine. Also generates cmd and data ACKs
|
|
machine: process(clk)
|
|
begin
|
|
if rising_edge(clk) then
|
|
if rst = '1' then
|
|
state <= STANDBY;
|
|
cmd_mode <= "000";
|
|
else
|
|
-- First clk down of a new cycle. Latch a request if any
|
|
-- or get out.
|
|
if start_cmd = '1' then
|
|
state <= DATA;
|
|
cmd_mode <= cmd_mode_i;
|
|
elsif end_cmd = '1' then
|
|
state <= STANDBY;
|
|
end if;
|
|
end if;
|
|
end if;
|
|
end process;
|
|
|
|
-- Run the bit counter in DATA state. It will update on rising
|
|
-- SCK edges. It starts at d_clks on command latch
|
|
count_bit: process(clk)
|
|
begin
|
|
if rising_edge(clk) then
|
|
if rst = '1' then
|
|
bit_count <= (others => '0');
|
|
else
|
|
if start_cmd = '1' then
|
|
bit_count <= cmd_clks_i;
|
|
elsif state /= DATA then
|
|
bit_count <= (others => '1');
|
|
elsif sck_recv = '1' then
|
|
bit_count <= std_ulogic_vector(unsigned(bit_count) - 1);
|
|
end if;
|
|
end if;
|
|
end if;
|
|
end process;
|
|
|
|
-- Shift output data
|
|
shift_out: process(clk)
|
|
begin
|
|
if rising_edge(clk) then
|
|
-- Starting a command
|
|
if start_cmd = '1' then
|
|
oreg <= cmd_txd_i(7 downto 0);
|
|
elsif sck_send = '1' then
|
|
-- Get shift amount
|
|
if data_single(cmd_mode) then
|
|
oreg <= oreg(6 downto 0) & '0';
|
|
elsif data_dual(cmd_mode) then
|
|
oreg <= oreg(5 downto 0) & "00";
|
|
else
|
|
oreg <= oreg(3 downto 0) & "0000";
|
|
end if;
|
|
end if;
|
|
end if;
|
|
end process;
|
|
|
|
-- Data out
|
|
sdat_o(0) <= oreg(7);
|
|
dl2: if DATA_LINES > 1 generate
|
|
sdat_o(1) <= oreg(6);
|
|
end generate;
|
|
dl4: if DATA_LINES > 2 generate
|
|
sdat_o(2) <= oreg(5);
|
|
sdat_o(3) <= oreg(4);
|
|
end generate;
|
|
|
|
-- Data lines direction
|
|
dlines: process(all)
|
|
begin
|
|
for i in DATA_LINES-1 downto 0 loop
|
|
sdat_oe(i) <= '0';
|
|
if state = DATA then
|
|
-- In single mode, we always enable MOSI, otherwise
|
|
-- we control the output enable based on the direction
|
|
-- of transfer.
|
|
--
|
|
if i = 0 and (data_single(cmd_mode) or data_write(cmd_mode)) then
|
|
sdat_oe(i) <= '1';
|
|
end if;
|
|
if i = 1 and data_dual(cmd_mode) and data_write(cmd_mode) then
|
|
sdat_oe(i) <= '1';
|
|
end if;
|
|
if i > 0 and data_quad(cmd_mode) and data_write(cmd_mode) then
|
|
sdat_oe(i) <= '1';
|
|
end if;
|
|
end if;
|
|
end loop;
|
|
end process;
|
|
|
|
-- Latch input data no delay
|
|
input_delay_0: if INPUT_DELAY = 0 generate
|
|
process(clk)
|
|
begin
|
|
if rising_edge(clk) then
|
|
dat_i_l <= sdat_i;
|
|
end if;
|
|
end process;
|
|
end generate;
|
|
|
|
-- Latch input data half clock delay
|
|
input_delay_1: if INPUT_DELAY = 1 generate
|
|
process(clk)
|
|
begin
|
|
if falling_edge(clk) then
|
|
dat_i_l <= sdat_i;
|
|
end if;
|
|
end process;
|
|
end generate;
|
|
|
|
-- Shift input data
|
|
shift_in: process(clk)
|
|
begin
|
|
if rising_edge(clk) then
|
|
if rst = '1' then
|
|
ireg <= (others => '0');
|
|
end if;
|
|
|
|
-- Delay the receive signal to match the input latch
|
|
if state = DATA then
|
|
sck_recv_d <= sck_recv;
|
|
else
|
|
sck_recv_d <= '0';
|
|
end if;
|
|
|
|
-- Generate read data acks
|
|
if bit_count = "000" and sck_recv = '1' then
|
|
dat_ack_l <= not cmd_mode(0);
|
|
else
|
|
dat_ack_l <= '0';
|
|
end if;
|
|
|
|
-- And delay them as well
|
|
d_ack_o <= dat_ack_l;
|
|
|
|
-- Shift register on delayed data & receive signal
|
|
if sck_recv_d = '1' then
|
|
if DATA_LINES = 1 then
|
|
ireg <= ireg(6 downto 0) & dat_i_l(0);
|
|
else
|
|
if data_dual(cmd_mode) then
|
|
ireg <= ireg(5 downto 0) & dat_i_l(1) & dat_i_l(0);
|
|
elsif data_quad(cmd_mode) then
|
|
ireg <= ireg(3 downto 0) & dat_i_l(3) & dat_i_l(2) & dat_i_l(1) & dat_i_l(0);
|
|
else
|
|
assert(data_single(cmd_mode));
|
|
ireg <= ireg(6 downto 0) & dat_i_l(1);
|
|
end if;
|
|
end if;
|
|
end if;
|
|
end if;
|
|
end process;
|
|
|
|
-- Data recieve register
|
|
d_rxd_o <= ireg;
|
|
|
|
end architecture;
|