dcache: Trim one cycle from the load hit path

Currently we don't get the result from a load that hits in the dcache
until the fourth cycle after the instruction was presented to
loadstore1.  This trims this back to 3 cycles by taking the low order
bits of the address generated in loadstore1 into dcache directly (not
via the output register of loadstore1) and using them to address the
read port of the dcache data RAM.  We use the lower 12 address bits
here in the expectation that any reasonable data cache design will
have a set size of 4kB or less in order to avoid the aliasing problems
that can arise with a virtually-indexed physically-tagged cache if
the set size is greater than the smallest page size provided by the
MMU.

With this we can get rid of r2 and drive the signals going to
writeback from r1, since the load hit data is now available one
cycle earlier.  We need a multiplexer on the read address of the
data cache RAM in order to handle the second doubleword of an
unaligned access.

One small complication is that we now need an extra cycle in the case
of an unaligned load which misses in the data cache and which reads
the 2nd-last and last doublewords of a cache line.  This is the reason
for the PRE_NEXT_DWORD state; if we just go straight to NEXT_DWORD
then we end up having the write of the last doubleword of the cache
line and the read of that same doubleword occurring in the same
cycle, which means we read stale data rather than the just-fetched
data.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
pull/153/head
Paul Mackerras 5 years ago
parent 5d85ede97d
commit 81d777be02

@ -229,6 +229,8 @@ package common is
xerc : xer_common_t;
reserve : std_ulogic;
rc : std_ulogic;
early_low_addr : std_ulogic_vector(11 downto 0);
early_valid : std_ulogic;
end record;

type DcacheToWritebackType is record

@ -124,6 +124,7 @@ architecture rtl of dcache is
-- Cache state machine
type state_t is (IDLE, -- Normal load hit processing
PRE_NEXT_DWORD, -- Extra state before NEXT_DWORD
NEXT_DWORD, -- Starting the 2nd xfer of misaligned
LOAD_UPDATE, -- Load with update extra cycle
LOAD_UPDATE2, -- Load with update extra cycle
@ -184,24 +185,6 @@ architecture rtl of dcache is

signal r1 : reg_stage_1_t;

-- Second stage register, only used for load hits
--
type reg_stage_2_t is record
hit_way : way_t;
hit_load_valid : std_ulogic;
load_is_update : std_ulogic;
load_reg : std_ulogic_vector(4 downto 0);
data_shift : std_ulogic_vector(2 downto 0);
length : std_ulogic_vector(3 downto 0);
sign_extend : std_ulogic;
byte_reverse : std_ulogic;
xerc : xer_common_t;
last_dword : std_ulogic;
second_dword : std_ulogic;
end record;

signal r2 : reg_stage_2_t;

-- Reservation information
--
type reservation_t is record
@ -221,6 +204,10 @@ architecture rtl of dcache is
signal req_addr : std_ulogic_vector(63 downto 0);
signal req_laddr : std_ulogic_vector(63 downto 0);
signal req_sel : std_ulogic_vector(7 downto 0);
signal next_addr : std_ulogic_vector(63 downto 0);

signal early_req_addr : std_ulogic_vector(11 downto 0);
signal early_req_row : row_t;

signal cancel_store : std_ulogic;
signal set_rsrv : std_ulogic;
@ -404,6 +391,12 @@ begin
end generate;
end generate;

-- Wishbone read and write and BRAM write sel bits generation
bus_sel <= wishbone_data_sel(d_in.length, d_in.addr);

-- See if the operation crosses two doublewords
two_dwords <= or (bus_sel(15 downto 8));

-- Cache request parsing and hit detection
dcache_request : process(all)
variable is_hit : std_ulogic;
@ -444,6 +437,9 @@ begin
req_laddr <= req_addr(63 downto LINE_OFF_BITS) &
(LINE_OFF_BITS-1 downto 0 => '0');

-- Address of next doubleword, used for unaligned accesses
next_addr <= std_ulogic_vector(unsigned(d_in.addr(63 downto 3)) + 1) & "000";

-- Test if pending request is a hit on any way
hit_way := 0;
is_hit := '0';
@ -480,17 +476,21 @@ begin

req_op <= op;

-- Versions of the address and row number that are valid one cycle earlier
-- in the cases where we need to read the cache data BRAM.
if r1.state = IDLE and op = OP_LOAD_HIT and two_dwords = '1' then
early_req_addr <= next_addr(11 downto 0);
elsif r1.state /= IDLE and r1.two_dwords = '1' and r1.second_dword = '0' then
early_req_addr <= r1.next_addr(11 downto 0);
else
early_req_addr <= d_in.early_low_addr;
end if;
early_req_row <= get_row(x"0000000000000" & early_req_addr);
end process;

-- Wire up wishbone request latch out of stage 1
wishbone_out <= r1.wb;

-- Wishbone read and write and BRAM write sel bits generation
bus_sel <= wishbone_data_sel(d_in.length, d_in.addr);

-- See if the operation crosses two doublewords
two_dwords <= or (bus_sel(15 downto 8));

-- TODO: Generate errors
-- err_nc_collision <= '1' when req_op = OP_BAD else '0';

@ -540,14 +540,14 @@ begin
-- The mux on d_out.write reg defaults to the normal load hit case.
d_out.write_enable <= '0';
d_out.valid <= '0';
d_out.write_reg <= r2.load_reg;
d_out.write_data <= cache_out(r2.hit_way);
d_out.write_len <= r2.length;
d_out.write_shift <= r2.data_shift;
d_out.sign_extend <= r2.sign_extend;
d_out.byte_reverse <= r2.byte_reverse;
d_out.second_word <= r2.second_dword;
d_out.xerc <= r2.xerc;
d_out.write_reg <= r1.req.write_reg;
d_out.write_data <= cache_out(r1.hit_way);
d_out.write_len <= r1.req.length;
d_out.write_shift <= r1.req.addr(2 downto 0);
d_out.sign_extend <= r1.req.sign_extend;
d_out.byte_reverse <= r1.req.byte_reverse;
d_out.second_word <= r1.second_dword;
d_out.xerc <= r1.req.xerc;
d_out.rc <= '0'; -- loads never have rc=1
d_out.store_done <= '0';

@ -562,26 +562,27 @@ begin
--

-- Sanity: Only one of these must be set in any given cycle
assert (r1.update_valid and r2.hit_load_valid) /= '1' report
assert (r1.update_valid and r1.hit_load_valid) /= '1' report
"unexpected hit_load_delayed collision with update_valid"
severity FAILURE;
assert (r1.slow_valid and r1.stcx_fail) /= '1' report
"unexpected slow_valid collision with stcx_fail"
severity FAILURE;
assert ((r1.slow_valid or r1.stcx_fail) and r2.hit_load_valid) /= '1' report
assert ((r1.slow_valid or r1.stcx_fail) and r1.hit_load_valid) /= '1' report
"unexpected hit_load_delayed collision with slow_valid"
severity FAILURE;
assert ((r1.slow_valid or r1.stcx_fail) and r1.update_valid) /= '1' report
"unexpected update_valid collision with slow_valid or stcx_fail"
severity FAILURE;

-- Delayed load hit case is the standard path
if r2.hit_load_valid = '1' then
-- Load hit case is the standard path
if r1.hit_load_valid = '1' then
d_out.write_enable <= '1';

-- If there isn't another dword to go and
-- it's not a load with update, complete it now
if r2.last_dword = '1' and r2.load_is_update = '0' then
if (r1.second_dword or not r1.two_dwords) = '1' and
r1.req.update = '0' then
report "completing load hit";
d_out.valid <= '1';
end if;
@ -693,7 +694,7 @@ begin
begin
-- Cache hit reads
do_read <= '1';
rd_addr <= std_ulogic_vector(to_unsigned(req_row, ROW_BITS));
rd_addr <= std_ulogic_vector(to_unsigned(early_req_row, ROW_BITS));
cache_out(i) <= dout;

-- Write mux:
@ -732,23 +733,11 @@ begin

--
-- Cache hit synchronous machine for the easy case. This handles
-- non-update form load hits and stage 1 to stage 2 transfers
-- non-update form load hits
--
dcache_fast_hit : process(clk)
begin
if rising_edge(clk) then
-- stage 1 -> stage 2
r2.hit_load_valid <= r1.hit_load_valid;
r2.hit_way <= r1.hit_way;
r2.load_is_update <= r1.req.update;
r2.load_reg <= r1.req.write_reg;
r2.data_shift <= r1.req.addr(2 downto 0);
r2.length <= r1.req.length;
r2.sign_extend <= r1.req.sign_extend;
r2.byte_reverse <= r1.req.byte_reverse;
r2.second_dword <= r1.second_dword;
r2.last_dword <= r1.second_dword or not r1.two_dwords;

-- If we have a request incoming, we have to latch it as d_in.valid
-- is only set for a single cycle. It's up to the control logic to
-- ensure we don't override an uncompleted request (for now we are
@ -759,7 +748,7 @@ begin
r1.req <= d_in;
r1.second_dword <= '0';
r1.two_dwords <= two_dwords;
r1.next_addr <= std_ulogic_vector(unsigned(d_in.addr(63 downto 3)) + 1) & "000";
r1.next_addr <= next_addr;
r1.next_sel <= bus_sel(15 downto 8);

report "op:" & op_t'image(req_op) &
@ -912,6 +901,9 @@ begin
when OP_BAD =>
end case;

when PRE_NEXT_DWORD =>
r1.state <= NEXT_DWORD;

when RELOAD_WAIT_ACK =>
-- Requests are all sent if stb is 0
stbs_done := r1.wb.stb = '0';
@ -958,7 +950,7 @@ begin
-- we also need to do the deferred update cycle.
r1.slow_valid <= '1';
if r1.two_dwords and not r1.second_dword then
r1.state <= NEXT_DWORD;
r1.state <= PRE_NEXT_DWORD;
elsif r1.req.update = '1' then
r1.state <= LOAD_UPDATE2;
report "completing miss with load-update !";

@ -89,5 +89,9 @@ begin

-- Update outputs
l_out <= r;

-- Asynchronous output of the low-order address bits (latched in dcache)
l_out.early_low_addr <= lsu_sum(11 downto 0);
l_out.early_valid <= l_in.valid;
end process;
end;

Loading…
Cancel
Save