Commit Graph

797 Commits (49f3d1e77a14e8c2d8c35c1316b8d35754a1b428)
 

Author SHA1 Message Date
Paul Mackerras 209aa9ce3f loadstore1: Reduce busy cycles
This reduces the number of cycles where loadstore1 asserts its busy
output, leading to increased throughput of loads and stores.  Loads
that hit in the cache can now be executed at the rate of one every two
cycles.  Stores take 4 cycles assuming the wishbone slave responds
with an ack the cycle after we assert strobe.

To achieve this, the state machine code is split into two parts, one
for when we have an existing instruction in progress, and one for
starting a new instruction.  We can now combinatorially clear busy and
start a new instruction in the same cycle that we get a done signal
from the dcache; in other words we are completing one instruction and
potentially writing back results in the same cycle that we start a new
instruction and send its address and data to the dcache.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 1d09daae03 loadstore1: Complete mfspr/mtspr a cycle later
This makes mfspr and mtspr complete (and mfspr write back) on the
cycle after the instruction is received from execute1, rather than
on the same cycle.  This makes them match all other instructions
that execute in one cycle.  Because these instructions are marked
as single-issue, there wasn't the possibility of having two
instructions complete on the same cycle (which we can't cope with),
but it is better to fix this.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 6701e7346b core: Use a busy signal rather than a stall
This changes the instruction dependency tracking so that we can
generate a "busy" signal from execute1 and loadstore1 which comes
along one cycle later than the current "stall" signal.  This will
enable us to signal busy cycles only when we need to from loadstore1.

The "busy" signal from execute1/loadstore1 indicates "I didn't take
the thing you gave me on this cycle", as distinct from the previous
stall signal which meant "I took that but don't give me anything
next cycle".  That means that decode2 proactively gives execute1
a new instruction as soon as it has taken the previous one (assuming
there is a valid instruction available from decode1), and that then
sits in decode2's output until execute1 can take it.  So instructions
are issued by decode2 somewhat earlier than they used to be.

Decode2 now only signals a stall upstream when its output buffer is
full, meaning that we can fill up bubbles in the upstream pipe while a
long instruction is executing.  This gives a small boost in
performance.

This also adds dependency tracking for rA updates by update-form
load/store instructions.

The GPR and CR hazard detection machinery now has one extra stage,
which may not be strictly necessary.  Some of the code now really
only applies to PIPELINE_DEPTH=1.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 62b24a8dae icache: Improve latencies when reloading cache lines
The icache can now detect a hit on a line being refilled from memory,
as we have an array of individual valid bits per row for the line
that is currently being loaded.  This enables the request that
initiated the refill to be satisfied earlier, and also enables
following requests to the same cache line to be satisfied before the
line is completely refilled.  Furthermore, the refill now starts
at the row that is needed.  This should reduce the latency for an
icache miss.

We now get a 'sequential' indication from fetch1, and use that to know
when we can deliver an instruction word using the other half of the
64-bit doubleword that was read last cycle.  This doesn't make much
difference at the moment, but it frees up cycles where we could test
whether the next line is present in the cache so that we could
prefetch it if not.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 0809bc898b multiply: Use DSP48 slices for multiplication on Xilinx FPGAs
This adds a custom implementation of the multiplier which uses 16
DSP48E1 slices to do a 64x64 bit multiplication in 2 cycles.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 9880fc7435 multiply: Move selection of result bits into execute1
This puts the logic that selects which bits of the multiplier result
get written into the destination GPR into execute1, moved out from
multiply.

The multiplier is now expected to do an unsigned multiplication of
64-bit operands, optionally negate the result, detect 32-bit
or 64-bit signed overflow of the result, and return a full 128-bit
result.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras f80da65799 core: Double the dcache and icache sizes
This makes the dcache and icache both be 8kB.  This still only uses
one BRAM per way per cache on the Artix-7, since the BRAMs were only
half-used previously.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras b5a7dbb78d core: Remove fetch2 pipeline stage
The fetch2 stage existed primarily to provide a stash buffer for the
output of icache when a stall occurred.  However, we can get the same
effect -- of having the input to decode1 stay unchanged on a stall
cycle -- by using the read enable of the BRAMs in icache, and by
adding logic to keep the outputs unchanged on a clock cycle when
stall_in = 1.  This reduces branch and interrupt latency by one
cycle.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 49a4d9f67a Add core logging
This logs 256 bits of data per cycle to a ring buffer in BRAM.  The
data collected can be read out through 2 new SPRs or through the
debug interface.

The new SPRs are LOG_ADDR (724) and LOG_DATA (725).  LOG_ADDR contains
the buffer write pointer in the upper 32 bits (in units of entries,
i.e. 32 bytes) and the read pointer in the lower 32 bits (in units of
doublewords, i.e. 8 bytes).  Reading LOG_DATA gives the doubleword
from the buffer at the read pointer and increments the read pointer.
Setting bit 31 of LOG_ADDR inhibits the trace log system from writing
to the log buffer, so the contents are stable and can be read.

There are two new debug addresses which function similarly to the
LOG_ADDR and LOG_DATA SPRs.  The log is frozen while either or both of
the LOG_ADDR SPR bit 31 or the debug LOG_ADDR register bit 31 are set.

The buffer defaults to 2048 entries, i.e. 64kB.  The size is set by
the LOG_LENGTH generic on the core_debug module.  Software can
determine the length of the buffer because the length is ORed into the
buffer write pointer in the upper 32 bits of LOG_ADDR.  Hence the
length of the buffer can be calculated as 1 << (31 - clz(LOG_ADDR)).

There is a program to format the log entries in a somewhat readable
fashion in scripts/fmt_log/fmt_log.c.  The log_entry struct in that
file describes the layout of the bits in the log entries.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras aab84acda8 scripts/mw_debug: Make progress counts display on one line
This outputs a carriage return rather than a newline after the
display of the progress count during the load and save operations.
This makes the output more compact and better looking.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 03f9d7a97e tests/xics: Fix assumption that interrupts happen immediately
Currently the test writes to the XICS and then checks that the
expected interrupt has happened.  This turns into a stbcix
instruction followed immediately by a load from the variable that
indicates whether an interrupt has happened.  It is possible for
it to take a few cycles for the store to reach the XICS and the
interrupt request signal to come back to the core, particularly
with improvements to the load/store unit and dcache.

This therefore adds a delay between storing to the XICS and
checking for the occurrence of an interrupt, so as to give the
signals time to propagate.  The delay loop does an arbitrary 10
iterations, and each iteration does two loads and one store to
(cacheable) memory.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 5a00029519 register_file: Report value being written before asserting it's not X
If a bug causes an indeterminate value to be written to a GPR, an
assert causes simulation to abort.  Move the assert after the report
of the GPR index and value so that we get to know what the bad value
is before the simulation terminates.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 12a257f01e
Merge pull request #205 from ozbenh/timing
Timing improvements
4 years ago
Paul Mackerras bf6cc2a05a
Merge pull request #204 from ozbenh/spi
Add an SPI master flash controller
4 years ago
Benjamin Herrenschmidt 176ae5c306 syscon: Remove combinational loop on ack and stall
Those hurt timings. Instead latch the wishbone response for one cycle

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
4 years ago
Benjamin Herrenschmidt 6c3a8bf417 bram: Remove combinational loop on stall
It hurts timing and is pointless

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
4 years ago
Benjamin Herrenschmidt e5aa0e9dc9 uart: Remove combinational loops on ack and stall signal
They hurt timing forcing signals to come from the master and back
again in one cycle. Stall isn't sampled by the master unless there
is an active cycle so masking it with cyc is pointless. Masking acks
is somewhat pointless too as we don't handle early dropping of cyc
in any of our slaves properly anyways.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
4 years ago
Benjamin Herrenschmidt 6aadad5a75 spi: Add booting from flash to litedram init
It will look for an ELF binary at the flash offset specified
for the board (currently 0x300000 on Arty but that could be
changed).

Note: litedram is regenerated in order to rebuild the init code,
which was done using a newer version of litedram from LiteX.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
4 years ago
Benjamin Herrenschmidt a89e1469ef spi: Add simulation support
This require the s25fl128s.vhd flash model and FMF libraries,
which will be built when passed to the Makefile via the
FLASH_MODEL_PATH argument. Otherwise a dummy module is used
which ties MISO to '1'.

The model isn't included as I'm not sure its licence (GPL) is
at this point, but it can be obtained from

https://github.com/ozbenh/microspi

FLASH_MODEL_PATH=<path to microspi>/model

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
4 years ago
Dan Horák 801bd3b8ee
flash-arty: update error message (#203)
Signed-off-by: Dan Horák <dan@danny.cz>
4 years ago
Benjamin Herrenschmidt 9b458a9aa6
dmi: Add ASYNC_REG attribute on synchronizers (#200)
This tells Vivado to keep them close among other things

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
4 years ago
Benjamin Herrenschmidt d266c9e67d
icache: Latch PLRU victim output (#199)
This stores the output of the PLRU big mux and clears the
tags and valid bits on the next cycle.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
4 years ago
Paul Mackerras 41d28bbdfc
Merge pull request #198 from ozbenh/litedram
Litedram: Timing improvements
4 years ago
Benjamin Herrenschmidt cc4dcb3597 spi: Add SPI Flash controller
This adds an SPI flash controller which supports direct
memory-mapped access to the flash along with a manual
mode to send commands.

The direct mode can be set via generic to default to single
wire or quad mode. The controller supports normal, dual and quad
accesses with configurable commands, clock divider, dummy clocks
etc...

The SPI clock can be an even divider of sys_clk starting at 2
(so max 50Mhz with our typical Arty designs).

A flash offset is carried via generics to syscon to tell SW about
which portion of the flash is reserved for the FPGA bitfile. There
is currently no plumbing to make the CPU reset past that address (TBD).

Note: Operating at 50Mhz has proven unreliable without adding some
delay to the sampling of the input data. I'm working in improving
this, in the meantime, I'm leaving the default set at 25 Mhz.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
4 years ago
Benjamin Herrenschmidt 15467fe536 litedram: L2 use latched refill_index
Not a huge difference since wb_req is itself a latch but
may as well

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
4 years ago
Benjamin Herrenschmidt 05bbbf0772 litedram: Pipeline store acks in L2
There is a long timing path to generate the ack signal from
the L2 cache as it's fully combinational for stores, including
signals coming from litedram.

Instead, pipeline the store acks. This will introduce a cycle
latency but should improve timing. Also the core will eventually
be smart enough not to wait for store acks to complete them anyway.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
4 years ago
Benjamin Herrenschmidt 5ae5f76558 arty/nexys-video: Update XDC
The DRAM related pins have some small changes in LiteX, so resync
and add the false path information as well.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
4 years ago
Benjamin Herrenschmidt b58ff724f6 litedram: Add stash buffer to the L2 cache wishbone interface
This breaks the long stall signal coming back to the processor
and helps improve overall timing.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
4 years ago
Benjamin Herrenschmidt b23fd6c5f1 litedram: Defer clearing of tags & valids to improve timing
Currently, there's a huge mux gathering the output of all the PLRUs
to select the victim way on cache miss. This is fed combinationally
into the clearing of the valid and tags.

In order to help timing, let's store it instead and perform the
clearing on the next cycle. The L2 doesn't respond to requests
when not in IDLE state so this should have no negative effects.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
4 years ago
Benjamin Herrenschmidt 7192ee825f litedram: Improve dram_tb error output
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
4 years ago
Anton Blanchard 7577cb18fb
Merge pull request #201 from mikey/github-actions
Move from travis to github workflows
4 years ago
Michael Neuling 9653b2952f Move from travis to github workflow
Github workflow gives us longer run times and faster startup.

Major kudos for this goes to @eine for the initial version and for
pushing us in this direction.

Signed-off-by: Michael Neuling <mikey@neuling.org>
4 years ago
Paul Mackerras 6bb3837b33
Merge pull request #194 from ozbenh/misc
Fix syscon registers usage and add "save" function to mw_debug
4 years ago
Benjamin Herrenschmidt 183d05de86 gitignore: Add more exlusions
litedram build directory used by the generator and the
verilator obj_dir can be taken out

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
4 years ago
Benjamin Herrenschmidt 63f10450a6 litedram: Fix DRAM init mem using too many address bits
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
4 years ago
Benjamin Herrenschmidt a93d9e77c9 litedram: Remove remnants of riscv-inits
We still had some wires bringing an extra serial port out of
litedram for the built-in riscv processor. This is all gone now
so take them out.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
4 years ago
Benjamin Herrenschmidt 3c99e6c31f mw_debug: Add "save" function to save memory to a file
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
4 years ago
Benjamin Herrenschmidt 3167515069 sw: Properly mask syscon register fields
Some fields might get extended with extra bits, use the appropriate
masks when reading the values.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
4 years ago
Michael Neuling 13da4caafb
Merge pull request #196 from ozbenh/makefile-lib-fix
Makefile: Improve unisim library generation
4 years ago
Michael Neuling 0739b55bc2
Merge pull request #195 from shenki/nexys-video
Nexys video
4 years ago
Benjamin Herrenschmidt 097d19fd32 Makefile: Improve unisim library generation
The rewrite of the Makefile to use "ghdl -c" somewhat broke building
the unisim library as ghdl doesn't yet support putting files in
separate libraries from a single command line invocation.

The workaround at the time was to put the entire project in "unisim"
which is ... weird and will break if we try to add another library
such as fmf.

This fixes it by generating the library separately using "ghdl -i"

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
4 years ago
Joel Stanley fcdc01aa05 flash-arty: Re-add support for running from any path
The changes in d3c274d01e ("flash-arty: Add support for specifying the file type")
added a local jtagspi.cfg, which meant openocd must be run from the root
of the microwatt directory.

This puts the content into the xilinx-xc7.cfg so the script can be used
from any path again.

Signed-off-by: Joel Stanley <joel@jms.id.au>
4 years ago
Joel Stanley 002858ddde flash-arty: Support Nexys Video's a200
Not an Arty but Anton tests on this board.

Signed-off-by: Joel Stanley <joel@jms.id.au>
4 years ago
Michael Neuling e46c46ab5f
Merge pull request #193 from paulusmack/master
Minor improvements and reformatting
4 years ago
Paul Mackerras cff40237c7
Merge pull request #182 from mikey/travis
Travis and testing improvements
4 years ago
Benjamin Herrenschmidt b863791e38
icache: Fix icbi potentially clobbering the icache (#192)
icbi currently just resets the icache. This has some nasty side
effects such as also clearing the TLB, but also the wishbone interface.

That means that any ongoing cycle will be dropped.

However, most of our slaves don't handle that well and will continue
sending acks for already issued requests.

Under some circumstances we can thus restart an icache load and get
spurious ack/data from the wishbone left over from the "cancelled"
sequence.

This has broken booting Linux for me.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
4 years ago
Paul Mackerras afa82bea9c decode2: Reformat to 4-space indentation
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras d5c8c33bae decode1: Reformat to 4-space indentation
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras af909840e6 decode1: Make ld/std and lwa not be single-issue
These were missed earlier when the single-issue flag was turned off on
the other loads and stores by commit 1a244d3470 ("Remove single-issue
constraint for most loads and stores").

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Michael Neuling a740c4b7af Improve Travis to run as a matrix job
Can now run all 999 random tests and unit tests in Travis.

Kudos for this goes to @eine. Based on his input from here:
  https://github.com/antonblanchard/microwatt/pull/182#issuecomment-637926957

Signed-off-by: Michael Neuling <mikey@neuling.org>
4 years ago