This implements the byte-reverse halfword, word and doubleword
instructions: brh, brw, and brd. These instructions were added to the
ISA in version 3.1. They use a new OP_BREV insn_type value. The
logic for these instructions is implemented in logical.vhdl.
In order to avoid going over 64 insn_type values, OP_AND and OP_OR
were combined into OP_LOGIC, which is like OP_AND except that the RS
input can be inverted as well as the RB input. The various forms of
OR instruction are then implemented using the identity
a OR b = NOT (NOT a AND NOT b)
The 'is_signed' field of the instruction decode table is used to
indicate that RS should be inverted.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This implements the setbc, setnbc, setbcr and setnbcr instructions.
Because the insn_type_t type already has 64 elements, this uses the
existing OP_SETB for the new instructions, and has execute1 compute
different results depending on bits 6-9 of the instruction.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This arranges to generate an illegal instruction type program
interrupt for illegal prefixed instructions, that is, those where the
suffix is not a legal value given the prefix, or the prefix has a
reserved value in the subtype field. This implementation doesn't
generate an interrupt for the invalid 8LS:D and MLS:D instruction
forms where R = 1 and RA != 0. (In those cases it uses (RA) as the
addend, i.e. it ignores the R bit.)
This detects the case where the address of an instruction prefix is
equal mod 64 to 60, and generates an alignment interrupt in that case.
This also arranges to set bit 34 of SRR1 when an interrupt occurs due
to a prefixed instruction, for those interrupts where that is required
(i.e. trace, alignment, floating-point unavailable, data storage, data
segment, and most cases of program interrupt).
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds logic to do basic decoding of the prefixed instructions
defined in PowerISA v3.1B which are in the SFFS (Scalar Fixed plus
Floating-Point Subset) compliancy subset. In PowerISA v3.1B SFFS,
there are 14 prefixed load/store instructions plus the prefixed no-op
instruction (pnop). The prefixed load/store instructions all use an
extended version of D-form, which has an extra 18 bits of displacement
in the prefix, plus an 'R' bit which enables PC-relative addressing.
When decode1 sees an instruction word where the insn_code is
INSN_prefix (i.e. the primary opcode was 1), it stores the prefix word
and sends nothing down to decode2 in that cycle. When the next valid
instruction word arrives, it is interpreted as a suffix, meaning that
its insn_code gets modified before being used to look up the decode
table.
The insn_code values are rearranged so that the values for
instructions which are the suffix of a valid prefixed instruction are
all at even indexes, and the corresponding prefixed instructions
follow immediately, so that an insn_code value can be converted to the
corresponding prefixed value by setting the LSB of the insn_code
value. There are two prefixed instructions, pld and pstd, for which
the suffix is not a valid SFFS instruction by itself, so these have
been given dummy insn_code values which decode as illegal (INSN_op57
and INSN_op61).
For a prefixed instruction, decode1 examines the type and subtype
fields of the prefix and checks that the suffix is valid for the type
and subtype. This check doesn't affect which entry of the decode
table is used; the result is passed down to decode2, and will in
future be acted upon in execute1.
The instruction address passed down to decode2 is the address of the
prefix. To enable this, part of the instruction address is saved when
the prefix is seen, and then the instruction address received from
icache is partly overlaid by the saved prefix address. Because
prefixed instructions are not permitted to cross 64-byte boundaries,
we only need to save bits 5:2 of the instruction to do this. If the
alignment restriction ever gets relaxed, we will then need to save
more bits of the address.
Decode2 has been extended to handle the R bit of the prefix (in 8LS
and MLS forms) and to be able to generate the 34-bit immediate value
from the prefix and suffix.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This moves the insn_code values for mcrfs, mtfsb0/1 and mtfsfi into
the region used for floating-point instructions. This means that in
no-FPU implementations, they will get turned into illegal instructions
in predecode. We then don't need the code in execute1 that makes FP
instructions illegal in no-FPU implementations.
We also remove the NONE value for unit_t, since it was only ever used
with insn_type = OP_ILLEGAL, and the check for unit = NONE was
redundant with the check for insn_type = OP_ILLEGAL. Thus the check
for unit = NONE is no longer needed and is removed here.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Instead of sending down the predicted taken/not-taken bits with the
target of the branch, we now send them down with the branch itself.
Previously icache adjusted for this by sending the prediction bits to
decode1 without a 1-clock delay while everything else had a 1-clock
delay. Now icache keeps the prediction bits with the rest of the
attributes for the request.
Also fix a buglet in fetch1 where the first address sent out after
reset didn't have .req set. Currently this doesn't cause a problem
because icache doesn't really look at .req.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Allows to trigger on rising/falling/both edge, as well
as high/low level.
Registers are compatible with Linux ftgpio010 driver.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Paul Mackerras
Matt Johnston