dcache: Ease timing on wishbone data and byte selects

This eliminates a path where the inputs to r1.wb.dat and r1.wb.sel
depend on req_op, which depends on the TLB and cache hit detection.
In fact they only need to depend on the nature of the request in
r0.req (i.e. DCBZ, store, cacheable load, or non-cacheable load).
This sets them at the beginning of the code for IDLE state rather
than inside the req_op case statement.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>

dcache.vhdl

@@ -1250,8 +1250,18 @@ begin
                     req.mmu_req := r0.mmu_req;
                     req.dcbz := r0.req.dcbz;
                     req.real_addr := ra;
+                    -- Force data to 0 for dcbz
+                    if r0.req.dcbz = '0' then
                         req.data := r0.req.data;
+                    else
+                        req.data := (others => '0');
+                    end if;
+                    -- Select all bytes for dcbz and for cacheable loads
+                    if r0.req.dcbz = '1' or (r0.req.load = '1' and r0.req.nc = '0') then
+                        req.byte_sel := (others => '1');
+                    else
                         req.byte_sel := r0.req.byte_sel;
+                    end if;
                     req.hit_way := req_hit_way;
                     req.same_tag := req_same_tag;
 
@@ -1268,7 +1278,9 @@ begin
 		case r1.state is
                 when IDLE =>
                     r1.wb.adr <= req.real_addr(r1.wb.adr'left downto 0);
-                    r1.dcbz <= '0';
+                    r1.wb.sel <= req.byte_sel;
+                    r1.wb.dat <= req.data;
+                    r1.dcbz <= req.dcbz;
 
                     -- Keep track of our index and way for subsequent stores.
                     r1.store_index <= get_index(req.real_addr);
@@ -1298,7 +1310,6 @@ begin
 			    " tag:" & to_hstring(get_tag(req.real_addr));
 
 			-- Start the wishbone cycle
-			r1.wb.sel <= (others => '1');
 			r1.wb.we  <= '0';
 			r1.wb.cyc <= '1';
 			r1.wb.stb <= '1';
@@ -1308,7 +1319,6 @@ begin
                         r1.write_tag <= '1';
 
 		    when OP_LOAD_NC =>
-                        r1.wb.sel <= req.byte_sel;
                         r1.wb.cyc <= '1';
                         r1.wb.stb <= '1';
 			r1.wb.we <= '0';
@@ -1316,8 +1326,6 @@ begin
 
                     when OP_STORE_HIT | OP_STORE_MISS =>
                         if req.dcbz = '0' then
-                            r1.wb.sel <= req.byte_sel;
-                            r1.wb.dat <= req.data;
                             r1.state <= STORE_WAIT_ACK;
                             r1.acks_pending <= to_unsigned(1, 3);
                             r1.full <= '0';
@@ -1333,17 +1341,10 @@ begin
                         else
                             -- dcbz is handled much like a load miss except
                             -- that we are writing to memory instead of reading
-
-                            -- Start the wishbone writes
-                            r1.wb.sel <= (others => '1');
-                            r1.wb.dat <= (others => '0');
-
-                            -- Handle the rest like a load miss
                             r1.state <= RELOAD_WAIT_ACK;
                             if req.op = OP_STORE_MISS then
                                 r1.write_tag <= '1';
                             end if;
-                            r1.dcbz <= '1';
                         end if;
                         r1.wb.we <= '1';
                         r1.wb.cyc <= '1';