forked from cores/microwatt
You cannot select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
Paul Mackerras
49a4d9f67a
This logs 256 bits of data per cycle to a ring buffer in BRAM. The data collected can be read out through 2 new SPRs or through the debug interface. The new SPRs are LOG_ADDR (724) and LOG_DATA (725). LOG_ADDR contains the buffer write pointer in the upper 32 bits (in units of entries, i.e. 32 bytes) and the read pointer in the lower 32 bits (in units of doublewords, i.e. 8 bytes). Reading LOG_DATA gives the doubleword from the buffer at the read pointer and increments the read pointer. Setting bit 31 of LOG_ADDR inhibits the trace log system from writing to the log buffer, so the contents are stable and can be read. There are two new debug addresses which function similarly to the LOG_ADDR and LOG_DATA SPRs. The log is frozen while either or both of the LOG_ADDR SPR bit 31 or the debug LOG_ADDR register bit 31 are set. The buffer defaults to 2048 entries, i.e. 64kB. The size is set by the LOG_LENGTH generic on the core_debug module. Software can determine the length of the buffer because the length is ORed into the buffer write pointer in the upper 32 bits of LOG_ADDR. Hence the length of the buffer can be calculated as 1 << (31 - clz(LOG_ADDR)). There is a program to format the log entries in a somewhat readable fashion in scripts/fmt_log/fmt_log.c. The log_entry struct in that file describes the layout of the bits in the log entries. Signed-off-by: Paul Mackerras <paulus@ozlabs.org> |
5 years ago | |
|---|---|---|
| .github/workflows | 5 years ago | |
| constraints | 5 years ago | |
| fpga | 5 years ago | |
| hello_world | 5 years ago | |
| include | 5 years ago | |
| lib | 5 years ago | |
| litedram | 5 years ago | |
| media | 5 years ago | |
| micropython | 5 years ago | |
| openocd | 5 years ago | |
| rust_lib_demo | 5 years ago | |
| scripts | 5 years ago | |
| sim-unisim | 5 years ago | |
| tests | 5 years ago | |
| verilator | 5 years ago | |
| .gitignore | 5 years ago | |
| LICENSE | 5 years ago | |
| Makefile | 5 years ago | |
| README.md | 5 years ago | |
| cache_ram.vhdl | 5 years ago | |
| common.vhdl | 5 years ago | |
| control.vhdl | 5 years ago | |
| core.vhdl | 5 years ago | |
| core_debug.vhdl | 5 years ago | |
| core_dram_tb.vhdl | 5 years ago | |
| core_flash_tb.vhdl | 5 years ago | |
| core_tb.vhdl | 5 years ago | |
| countzero.vhdl | 5 years ago | |
| countzero_tb.vhdl | 5 years ago | |
| cr_file.vhdl | 5 years ago | |
| cr_hazard.vhdl | 5 years ago | |
| crhelpers.vhdl | 5 years ago | |
| dcache.vhdl | 5 years ago | |
| dcache_tb.vhdl | 5 years ago | |
| decode1.vhdl | 5 years ago | |
| decode2.vhdl | 5 years ago | |
| decode_types.vhdl | 5 years ago | |
| divider.vhdl | 5 years ago | |
| divider_tb.vhdl | 5 years ago | |
| dmi_dtm_dummy.vhdl | 5 years ago | |
| dmi_dtm_tb.vhdl | 5 years ago | |
| dmi_dtm_xilinx.vhdl | 5 years ago | |
| dram_tb.vhdl | 5 years ago | |
| execute1.vhdl | 5 years ago | |
| fetch1.vhdl | 5 years ago | |
| fetch2.vhdl | 5 years ago | |
| glibc_random.vhdl | 5 years ago | |
| glibc_random_helpers.vhdl | 5 years ago | |
| gpr_hazard.vhdl | 5 years ago | |
| helpers.vhdl | 5 years ago | |
| icache.vhdl | 5 years ago | |
| icache_tb.vhdl | 5 years ago | |
| icache_test.bin | 5 years ago | |
| insn_helpers.vhdl | 5 years ago | |
| loadstore1.vhdl | 5 years ago | |
| logical.vhdl | 5 years ago | |
| microwatt.core | 5 years ago | |
| mmu.vhdl | 5 years ago | |
| multiply.vhdl | 5 years ago | |
| multiply_tb.vhdl | 5 years ago | |
| plru.vhdl | 5 years ago | |
| plru_tb.vhdl | 5 years ago | |
| ppc_fx_insns.vhdl | 5 years ago | |
| register_file.vhdl | 5 years ago | |
| rotator.vhdl | 5 years ago | |
| rotator_tb.vhdl | 5 years ago | |
| sim_bram.vhdl | 5 years ago | |
| sim_bram_helpers.vhdl | 5 years ago | |
| sim_bram_helpers_c.c | 5 years ago | |
| sim_console.vhdl | 5 years ago | |
| sim_console_c.c | 5 years ago | |
| sim_jtag.vhdl | 5 years ago | |
| sim_jtag_socket.vhdl | 5 years ago | |
| sim_jtag_socket_c.c | 5 years ago | |
| sim_no_flash.vhdl | 5 years ago | |
| sim_uart.vhdl | 5 years ago | |
| sim_vhpi_c.c | 5 years ago | |
| sim_vhpi_c.h | 5 years ago | |
| soc.vhdl | 5 years ago | |
| spi_flash_ctrl.vhdl | 5 years ago | |
| spi_rxtx.vhdl | 5 years ago | |
| sync_fifo.vhdl | 5 years ago | |
| syscon.vhdl | 5 years ago | |
| utils.vhdl | 5 years ago | |
| wishbone_arbiter.vhdl | 5 years ago | |
| wishbone_bram_tb.bin | 5 years ago | |
| wishbone_bram_tb.vhdl | 5 years ago | |
| wishbone_bram_wrapper.vhdl | 5 years ago | |
| wishbone_debug_master.vhdl | 5 years ago | |
| wishbone_types.vhdl | 5 years ago | |
| writeback.vhdl | 5 years ago | |
| xics.vhdl | 5 years ago | |
README.md
Microwatt
A tiny Open POWER ISA softcore written in VHDL 2008. It aims to be simple and easy to understand.
Simulation using ghdl
You can try out Microwatt/Micropython without hardware by using the ghdl simulator. If you want to build directly for a hardware target board, see below.
- Build micropython. If you aren't building on a ppc64le box you will need a cross compiler. If it isn't available on your distro grab the powerpc64le-power8 toolchain from https://toolchains.bootlin.com. You may need to set the CROSS_COMPILE environment variable to the prefix used for your cross compilers. The default is powerpc64le-linux-gnu-.
git clone https://github.com/micropython/micropython.git
cd micropython
cd ports/powerpc
make -j$(nproc)
cd ../../../
A prebuilt micropython image is also available in the micropython/ directory.
-
Microwatt uses ghdl for simulation. Either install this from your distro or build it. Microwatt requires ghdl to be built with the LLVM or gcc backend, which not all distros do (Fedora does, Debian/Ubuntu appears not to). ghdl with the LLVM backend is likely easier to build.
If building ghdl from scratch is too much for you, the microwatt Makefile supports using Docker or Podman.
-
Next build microwatt:
git clone https://github.com/antonblanchard/microwatt
cd microwatt
make
To build using Docker:
make DOCKER=1
and to build using Podman:
make PODMAN=1
- Link in the micropython image:
ln -s ../micropython/ports/powerpc/build/firmware.bin main_ram.bin
Or if you were using the pre-built image:
ln -s micropython/firmware.bin main_ram.bin
- Now run microwatt, sending debug output to /dev/null:
./core_tb > /dev/null
Synthesis on Xilinx FPGAs using Vivado
-
Install Vivado (I'm using the free 2019.1 webpack edition).
-
Setup Vivado paths:
source /opt/Xilinx/Vivado/2019.1/settings64.sh
- Install FuseSoC:
pip3 install --user -U fusesoc
Fedora users can get FuseSoC package via
sudo dnf copr enable sharkcz/danny
sudo dnf install fusesoc
- Create a working directory and point FuseSoC at microwatt:
mkdir microwatt-fusesoc
cd microwatt-fusesoc
fusesoc library add microwatt /path/to/microwatt/
- Build using FuseSoC. For hello world (Replace nexys_video with your FPGA board such as --target=arty_a7-100):
fusesoc run --target=nexys_video microwatt --memory_size=16384 --ram_init_file=/path/to/microwatt/fpga/hello_world.hex
You should then be able to see output via the serial port of the board (/dev/ttyUSB1, 115200 for example assuming standard clock speeds). There is a know bug where initial output may not be sent - try the reset (not programming button) on your board if you don't see anything.
- To build micropython (currently requires 1MB of BRAM eg an Artix-7 A200):
fusesoc run --target=nexys_video microwatt
Testing
- A simple test suite containing random execution test cases and a couple of micropython test cases can be run with:
make -j$(nproc) check
Issues
This is functional, but very simple. We still have quite a lot to do:
- There are a few instructions still to be implemented
- Need to add caches and bypassing (in progress)
- Need to add supervisor state (in progress)