The flash chip on my board is an ISSI IS26LP256P chip. The ISSI chip
requires slightly different setup for quad mode from the other brands,
but works fine with the existing SPI flash interface logic here.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Treat the input as if it was padded with zeroes to a multiple
of 8. This is needed if the .data in a binary changes size, it
won't be a nice multiple of 4 or 8. At present the microwatt
binaries all are multiples of 8, but making code alterations could make
bin2hex fail unexpectedly.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Parameters are based on
https://github.com/gregdavill/OrangeCrab-test-sw/blob/main/hw/OrangeCrab-bitstream.py
and litex-boards orangecrab.py
rtt_nom and cmd_delay are overridden for OrangeCrab, we do the same here.
Generated with litedram and litex
62abf9c ("litedram_gen: Add block_until_ready port parameter to control blocking behaviour.")
add2746a ("tools/litex_cli: Rename wb to bus.")
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Recent litedram gets stuck at memtest unless block_until_ready=False.
(discussion in https://github.com/enjoy-digital/litedram/pull/292)
This change regenerates with latest litedram and litex
62abf9c ("litedram_gen: Add block_until_ready port parameter to control blocking behaviour.")
add2746a ("tools/litex_cli: Rename wb to bus.")
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
For now only the V2 of the board (slightly different pinout)
and only the A100T variant. I also haven't added GPIOs or anything
else on the PMODs really.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This makes the 64-bit wishbone buses have the address expressed in
units of doublewords (64 bits), and similarly for the 32-bit buses the
address is in units of words (32 bits). This is to comply with the
wishbone spec. Previously the addresses on the wishbone buses were in
units of bytes regardless of the bus data width, which is not correct
and caused problems with interfacing with externally-generated logic.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This is a NiteFury based PCIe M2 form-factor board originally
used for mining. It contains a speed grade 2 Artix 7 200T,
1GB of DDR3 and 32MB of flash.
The serial port is routed to pin 2 (RX) and 3 (TX) of the P2
connector (pin 1 is GND).
Note: Only 16MB of flash is currently usable until code is added
to configure the flash controller to use 4-bytes address commands
on that part.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some changes in LiteX broke us. Adapt the build system and
increase the init RAM size to 24KB.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The sdram_init ELF fails to link:
powerpc64le-linux-gnu-ld -static -nostdlib -T sdram_init.lds \
--gc-sections -o sdram_init.elf head.o main.o sdram.o console.o \
libc.o sdram_init.lds
powerpc64le-linux-gnu-ld: error: linker script file 'sdram_init.lds'
appears multiple times
make: *** [Makefile:70: sdram_init.elf] Error 1
This is because sdram_init.lds is one of the prerequisites, and thus is
contained in $^. However, it is also explicitly specified as part of
LDFLAGS, as the argument to -T.
Signed-off-by: Boris Shingarov <shingarov@labware.com>
Use a more generic console_init() instead of potato_uart_init(),
and do the same for interrupt control. There should be no
change in behaviour.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It will look for an ELF binary at the flash offset specified
for the board (currently 0x300000 on Arty but that could be
changed).
Note: litedram is regenerated in order to rebuild the init code,
which was done using a newer version of litedram from LiteX.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some fields might get extended with extra bits, use the appropriate
masks when reading the values.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Support for this has bitrotted and would require refactoring of L2 to
be brought back. It's also not really needed anymore now that we ship
pre-generated litedram and that LiteX supports what we do.
So take it out, which simplifies some of the scripts as well. This also
fixes up CSR alignment the sim model.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds a cache between the wishbone and litedram with the following
features (at this point, it's still evolving)
- 128 bytes line width in order to have a reasonable amount of
litedram pipelining on the 128-bit wide data port.
- Configurable geometry otherwise
- Stores are acked immediately on wishbone whether hit or miss
(minus a 2 cycles delay if there's a previous load response in the
way) and sent to LiteDRAM via 8 entries (configurable) store queue
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds an option to disable the main BRAM and instead copy a
payload stashed along with the init code in the secondary BRAM
into DRAM and boot from there
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds a simulated litedram model along with the necessary
Makefile gunk to verilate it and wrap it for use by ghdl.
The core_dram_tb test bench is a variant of core_tb with
LiteDRAM simulated. It's not built by default, an explicit
make core_dram_tb
is necessary as to not require verilator to be installed for
the normal build process (also it's slow'ish).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This changes the SoC interconnect such that the main 64-bit wishbone out
of the processor is first split between only 3 slaves (BRAM, DRAM and a
general "IO" bus) instead of all the slaves in the SoC.
The IO bus leg is then latched and down-converted to 32 bits data width,
before going through a second address decoder for the various IO devices.
This significantly reduces routing and timing pressure on the main bus,
allowing to get rid of frequent timing violations when synthetizing on
small'ish FPGAs such as the Artix-7 35T found on the original Arty board.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Things have changed a bit in upstream LiteX. LiteDRAM now exposes a
wishbone for the CSRs for example.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
console.c goes to a new lib/ where we'll store other general utilities
and console.h goes to include/
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds support for initializing the memory controller from microwatt
rather than using a built-in RiscV processor. This might require some
fixes to LiteX and LiteDRAM (they haven't been merged as of this commit
yet).
This is enabled in the shipped generated files and can be changed via
modifying the generator script to pass False to "mw_init"
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These provides some info about the SoC (though it's still somewhat
incomplete and needs more work, see comments).
There's also a control register for selecting DRAM vs. BRAM at 0
(and for soft-resetting the SoC but that isn't wired up yet).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This comes in two parts:
- A generator script which uses LiteX to generate litedram cores
along with their init files for various boards (currently Arty and
Nexys-video). This comes with configs for arty and nexys_video.
- A fusesoc "generator" which uses pre-generated litedram cores
The generation process is manual on purpose. This include pre-generated
cores for the two above boards.
This is done so that one doesn't have to install LiteX to build
microwatt. In addition, the generator script or wrapper vhdl tend to
break when LiteX changes significantly which happens.
This is still rather standalone and hasn't been plumbed into the SoC
or the FPGA toplevel files yet.
At this point LiteDRAM self-initializes using a built-in VexRiscv
"Minimum" core obtained from LiteX and included in this commit. There
is some plumbing to generate and cores that are initialized by Microwatt
directly but this isn't working yet and so isn't enabled yet.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Paul Mackerras
Matt Johnston
Michael Neuling