This adds litesdcard.v generated from the litex/litesdcard project,
along with logic in top-arty.vhdl to connect it into the system.
There is now a DMA wishbone coming in to soc.vhdl which is narrower
than the other wishbone masters (it has 32-bit data rather than
64-bit) so there is a widening/narrowing adapter between it and the
main wishbone master arbiter.
Also, litesdcard generates a non-pipelined wishbone for its DMA
connection, which needs to be converted to a pipelined wishbone. We
have a latch on both the incoming and outgoing sides of the wishbone
in order to help make timing (at the cost of two extra cycles of
latency).
litesdcard generates an interrupt signal which is wired up to input 3
of the ICS (IRQ 19).
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds a GPIO controller which provides 32 bits of I/O. The
registers are modelled on the set used by the gpio-ftgpio010.c driver
in the Linux kernel. Currently there is no interrupt capability
implemented, though an interrupt line from the GPIO subsystem to the
XICS has been connected.
For the Arty A7 board, GPIO lines 0 to 13 are connected to the pins
labelled IO0 to IO13 on the "shield" connector, GPIO lines 14 to 29
connect to IO26 to IO41, GPIO line 30 connects to the pin labelled A
(aka IO42), and GPIO line 31 is connected to LED 7.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds, as comments, lines which would if uncommented define
properties which associate the pins of the headers on the Arty A7
board with FPGA pins. It also adds properties for LEDs 1--3, also
commented out for now.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This imports via fusesoc a 16550 compatible (ie "standard") UART,
and wires it up optionally in the SoC instead of the potato one.
This also adds support for a second UART (which is always a
16550) to Arty, wired to JC "bottom" port.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
No cells matched 'get_cells -hierarchical -filter {NAME =~*/spi_rxtx/dat_i_l*}'. [build/microwatt_0/src/microwatt_0/fpga/arty_a7.xdc:42]
The signal is in it's own process so the net name ends up being
spi_rxtx/input_delay_1.dat_i_l_reg.
After this change the log shows:
Applied set_property IOB = TRUE for soc0/\spiflash_gen.spiflash /spi_rxtx/\input_delay_1.dat_i_l_reg . (constraint file fpga/arty_a7.xdc, line 42).
Applied set_property IOB = TRUE for soc0/\spiflash_gen.spiflash /spi_rxtx/\input_delay_1.dat_i_l_reg . (constraint file fpga/arty_a7.xdc, line 42).
Applied set_property IOB = TRUE for soc0/\spiflash_gen.spiflash /spi_rxtx/\input_delay_1.dat_i_l_reg . (constraint file fpga/arty_a7.xdc, line 42).
Applied set_property IOB = TRUE for soc0/\spiflash_gen.spiflash /spi_rxtx/\input_delay_1.dat_i_l_reg . (constraint file fpga/arty_a7.xdc, line 42).
Signed-off-by: Joel Stanley <joel@jms.id.au>
This adds an SPI flash controller which supports direct
memory-mapped access to the flash along with a manual
mode to send commands.
The direct mode can be set via generic to default to single
wire or quad mode. The controller supports normal, dual and quad
accesses with configurable commands, clock divider, dummy clocks
etc...
The SPI clock can be an even divider of sys_clk starting at 2
(so max 50Mhz with our typical Arty designs).
A flash offset is carried via generics to syscon to tell SW about
which portion of the flash is reserved for the FPGA bitfile. There
is currently no plumbing to make the CPU reset past that address (TBD).
Note: Operating at 50Mhz has proven unreliable without adding some
delay to the sampling of the input data. I'm working in improving
this, in the meantime, I'm leaving the default set at 25 Mhz.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The DRAM related pins have some small changes in LiteX, so resync
and add the false path information as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The old toplevel.vhdl becomes top-generic.vhdl, which is to be used
by platforms that do not have a litedram option.
Arty has its own top-arty.vhdl which supports litedram and is now
hooked up
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling
Paul Mackerras
Benjamin Herrenschmidt