Use a more generic console_init() instead of potato_uart_init(),
and do the same for interrupt control. There should be no
change in behaviour.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This imports via fusesoc a 16550 compatible (ie "standard") UART,
and wires it up optionally in the SoC instead of the potato one.
This also adds support for a second UART (which is always a
16550) to Arty, wired to JC "bottom" port.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Move the external interrupt generation to a separate module
"ICS" (source controller) which a register per source containing
currently only the priority control.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use a separate process to assign selected interrupts to the
interrupt array, and document them.
There's only one interrupt *for now* but that will change
and this way is clearer.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This makes the control bus currently going out of "soc" towards
litedram more generic for external IO devices added by the
top-level rather than inside the SoC proper.
This is mostly renaming of signals and a small change on how the
address decoder operates, using a separate "cascaded" decode for
the external IOs.
We make the region 0xc8nn_nnnn be the "external IO" region for
now.
This will make it easier / cleaner to add more external devices.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It will look for an ELF binary at the flash offset specified
for the board (currently 0x300000 on Arty but that could be
changed).
Note: litedram is regenerated in order to rebuild the init code,
which was done using a newer version of litedram from LiteX.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds an SPI flash controller which supports direct
memory-mapped access to the flash along with a manual
mode to send commands.
The direct mode can be set via generic to default to single
wire or quad mode. The controller supports normal, dual and quad
accesses with configurable commands, clock divider, dummy clocks
etc...
The SPI clock can be an even divider of sys_clk starting at 2
(so max 50Mhz with our typical Arty designs).
A flash offset is carried via generics to syscon to tell SW about
which portion of the flash is reserved for the FPGA bitfile. There
is currently no plumbing to make the CPU reset past that address (TBD).
Note: Operating at 50Mhz has proven unreliable without adding some
delay to the sampling of the input data. I'm working in improving
this, in the meantime, I'm leaving the default set at 25 Mhz.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some fields might get extended with extra bits, use the appropriate
masks when reading the values.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds an option to disable the main BRAM and instead copy a
payload stashed along with the init code in the secondary BRAM
into DRAM and boot from there
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This changes the SoC interconnect such that the main 64-bit wishbone out
of the processor is first split between only 3 slaves (BRAM, DRAM and a
general "IO" bus) instead of all the slaves in the SoC.
The IO bus leg is then latched and down-converted to 32 bits data width,
before going through a second address decoder for the various IO devices.
This significantly reduces routing and timing pressure on the main bus,
allowing to get rid of frequent timing violations when synthetizing on
small'ish FPGAs such as the Artix-7 35T found on the original Arty board.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Things have changed a bit in upstream LiteX. LiteDRAM now exposes a
wishbone for the CSRs for example.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This contains C definitions for various Microwatt internal MMIOs
and a set of accessors.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Benjamin Herrenschmidt