Commit Graph

77 Commits (49a4d9f67a21438a4af703027baa72211409857a)

Author SHA1 Message Date
Anton Blanchard b8fb721b81 Consolidate logical instructions
Consolidate and/andc/nand, or/orc/nor and xor/eqv, using a common
invert on the input and output. This saves us about 200 LUTs.

Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
5 years ago
Benjamin Herrenschmidt b56b46b7d1 icache: Set associative icache
This adds support for set associativity to the icache. It can still
be direct mapped by setting NUM_WAYS to 1.

The replacement policy uses a simple tree-PLRU for each set.

This is only lightly tested, tests pass but I have to double check
that we are using the ways effectively and not creating duplicates.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
5 years ago
Benjamin Herrenschmidt 004eb074c9 plru: Add a simple PLRU module
Tested in sim only for now

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
5 years ago
Paul Mackerras f7c393ba7e Add a rotate/mask/shift unit and use it in execute1
This adds a new entity 'rotator' which contains combinatorial logic
for rotating and masking 64-bit values.  It implements the operations
of the rlwinm, rlwnm, rlwimi, rldicl, rldicr, rldic, rldimi, rldcl,
rldcr, sld, slw, srd, srw, srad, sradi, sraw and srawi instructions.
It consists of a 3-stage 64-bit rotator using 4:1 multiplexors at
each stage, two mask generators, output logic and control logic.

The insn_type_t values used for these instructions have been reduced
to just 5: OP_RLC, OP_RLCL and OP_RLCR for the rotate and mask
instructions (clear both left and right, clear left, clear right
variants), OP_SHL for left shifts, and OP_SHR for right shifts.
The control signals for the rotator are derived from the opcode
and from the is_32bit and is_signed fields of the decode_rom_t.

The rotator is instantiated as an entity in execute1 so that we can
be sure we only have one of it.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
5 years ago
Paul Mackerras c9e92483b8 decode: Push mtspr/mfspr register decoding down into execute1
Instead of doing mfctr, mflr, mftb, mtctr, mtlr as separate ops,
just pass down mfspr and mtspr ops with the spr number and let
execute1 decode which SPR we're addressing.  This will help reduce
the number of instruction bits decode1 needs to look at.

In fact we now pass down the whole instruction from decode2 to
execute1.  We will need more bits of the instruction in future,
and the tools should just optimize away any that we don't end
up using.  Since the 'aa' bit was just a copy of an instruction
bit, we can now remove it from the record.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
5 years ago
Benjamin Herrenschmidt 586abb70a0 Update dependency
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
5 years ago
Anton Blanchard 26f70264b3 Update Makefile dependencies
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
5 years ago
Anton Blanchard b57325ce29 Merge branch 'divider' of https://github.com/paulusmack/microwatt 5 years ago
Paul Mackerras d5bc6c8824 Add a divider unit and a testbench for it
This adds a divider unit, connected to the core in much the same way
that the multiplier unit is connected.  The division algorithm is
very simple-minded, taking 64 clock cycles for any division (even
32-bit division instructions).

The decoding is simplified by making use of regularities in the
instruction encoding for div* and mod* instructions.  Instead of
having PPC_* encodings from the first-stage decoder for each of the
different div* and mod* instructions, we now just have PPC_DIV and
PPC_MOD, and the inputs to the divider that indicate what sort of
division operation to do are derived from instruction word bits.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
5 years ago
Benjamin Herrenschmidt 42d802bed0 Add distclean to Makefile
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
5 years ago
Benjamin Herrenschmidt 98f0994698 Add core debug module
This module adds some simple core controls:

  reset, stop, start, step

along with icache clear and reading the NIA and core
status bits

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org
5 years ago
Benjamin Herrenschmidt b46f81fae4 Wishbone debug module
This adds a debug module off the DMI (debug) bus which can act as a
wishbone master to generate read and write cycles.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
5 years ago
Benjamin Herrenschmidt ee52fd4d80 Add a debug (DMI) bus and a JTAG interface to it on Xilinx FPGAs
This adds a simple bus that can be mastered from an external
system via JTAG, which will be used to hookup various debug
modules.

It's loosely based on the RiscV model (hence the DMI name).

The module currently only supports hooking up to a Xilinx BSCANE2
but it shouldn't be too hard to adapt it to support different TAPs
if necessary.

The JTAG protocol proper is not exactly the RiscV one at this point,
though I might still change it.

This comes with some sim variants of Xilinx BSCANE2 and BUFG and a
test bench.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
5 years ago
Anton Blanchard 135805d2ac
Merge pull request #61 from antonblanchard/execute-cleanup
execute1 no longer needs sim_console
5 years ago
Anton Blanchard 6d85920068 execute1 no longer needs sim_console
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
5 years ago
Anton Blanchard 1b6eef2a5d Fix multiply_tb
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
5 years ago
Anton Blanchard 1e3e16e500 Add an icache testbench
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
5 years ago
Anton Blanchard 89849a6856 Add a simple direct mapped icache
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
5 years ago
Anton Blanchard b6b2c78163 Update Makefile dependencies
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
5 years ago
Benjamin Herrenschmidt 3ac1dbc737 Share soc.vhdl between FPGA and sim
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
5 years ago
Benjamin Herrenschmidt 8bfd6e5eae Use simulated UART in core test bench
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
5 years ago
Anton Blanchard 03fd06deaf Rework SOC reset
The old reset code was overly complicated and never worked properly.
Replace it with a simpler sequence that uses a couple of shift registers
to assert resets:

- Wait a number of external clock cycles before removing reset from
  the PLL.

- After the PLL locks and the external reset button isn't pressed,
  wait a number of PLL clock cycles before removing reset from the SOC.

Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
5 years ago
Anton Blanchard 5e140298a5 Rework decode2
The decode2 stage was spaghetti code and needed cleaning up.
Create a series of functions to pull fields from a ppc instruction
and also a series of helpers to extract values for the execution
units.

As suggested by Paul, we should pass all signals to the execution
units and only set the valid signal conditionally, which should
use less resources.

Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
5 years ago
Anton Blanchard f98370f9e6
Merge pull request #5 from antonblanchard/travis-test
Add an initial travis.yml
5 years ago
Anton Blanchard 2ee269abdb Add an initial travis.yml
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
5 years ago
Anton Blanchard 96787091a6 Add -Wall to CFLAGS
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
5 years ago
Anton Blanchard 5a29cb4699 Initial import of microwatt
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
5 years ago