This adds litesdcard.v generated from the litex/litesdcard project,
along with logic in top-arty.vhdl to connect it into the system.
There is now a DMA wishbone coming in to soc.vhdl which is narrower
than the other wishbone masters (it has 32-bit data rather than
64-bit) so there is a widening/narrowing adapter between it and the
main wishbone master arbiter.
Also, litesdcard generates a non-pipelined wishbone for its DMA
connection, which needs to be converted to a pipelined wishbone. We
have a latch on both the incoming and outgoing sides of the wishbone
in order to help make timing (at the cost of two extra cycles of
latency).
litesdcard generates an interrupt signal which is wired up to input 3
of the ICS (IRQ 19).
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This makes the icache snoop writes to memory in the same way that the
dcache does, thus making DMA cache-coherent for the icache as well as
the dcache.
This also simplifies the logic for the WAIT_ACK state by removing the
stbs_done variable, since is_last_row(r.store_row, r.end_row_ix) can
only be true when stbs_done is true.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Since the expression is_last_row(r1.store_row, r1.end_row_ix) can only
be true when stbs_done is true, there is no need to include stbs_done
in the expression for the reload being completed, and hence no need to
compute stbs_done in the RELOAD_WAIT_ACK state.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds a path where the wishbone that goes out to memory and I/O
also gets fed back to the dcache, which looks for writes that it
didn't initiate, and invalidates any cache line that gets written to.
This involves a second read port on the cache tag RAM for looking up
the snooped writes, and effectively a second write port on the cache
valid bit array to clear bits corresponding to snoop hits.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Update documentation to reference fusesoc init for Xilinx boards, for
those like me who have never used fusesoc before. Add a reference to the
board files for Digilent boards and comment on perhaps installing them
for other boards as appropriate.
Signed-off-by: Antony Vennard <antony@vennard.ch>
Our SPI controller sends 8 dummy clocks at boot which Ben
added for some Xilinx boards. This should be harmless but
it is confusing the flash testbench in the Caravel project.
Add a parameter so it can be overridden at the top level.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
We want much smaller caches and tlbs when building for sky130, so
allow the toplevel file to override the defaults.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
The protocol used by the spi bridge firmware changed as of openocd
v0.11. As this is the version packaged by Debian Bullseye, add the
firmware for convince.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Make sure the SPRs are initialized and we can't read X state.
(Mikey: rebased and added console/bin file for testing)
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
If the DAR and DSISR are read before they are written, we assert with:
register_file.vhdl:55:25:@60195ns:(report note): Writing GPR 09 00000000XXXXXXXX
register_file.vhdl:61:17:@60195ns:(assertion failure): Assertion violation
This initialises DAR/DSISR to avoid this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Check that stb, cyc and ack are never undefined. While not really needed
here, this also tests if --pragma synthesis_off/--pragma synthesis_on
works on all the tools we use.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
The idea here is that we can have multiple instructions in progress at
the same time as long as they all go to the same unit, because that
unit will keep them in order. If we get an instruction for a
different unit, we wait for all the previous instructions to finish
before executing it. Since the loadstore unit is the only one that is
currently pipelined, this boils down to saying that loadstore
instructions can go ahead while l_in.in_progress = 1 but other
instructions have to wait until it is 0.
This gives a 2% increase on coremark performance on the Arty A7-100
(from ~190 to ~194).
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This makes loadstore use a 3-stage pipeline. For now, only one
instruction goes through the pipe at a time. Completion and writeback
are still combinatorial off the valid signal back from the dcache, so
performance should be the same as before. In future it should be able
to sustain one load or store per cycle provided they hit in the
dcache.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This fixes two bugs which show up when multiple operations are in
flight in the dcache, and adds a 'hold' input which will be needed
when loadstore1 is pipelined.
The first bug is that dcache needs to sample the data for a store on
the cycle after the store request comes in even if the store request
is held up because of a previous request (e.g. if the previous request
is a load miss or a dcbz).
The second bug is that a load request coming in for a cache line being
refilled needs to be handled immediately in the case where it is for
the row whose data arrives on the same cycle. If it is not, then it
will be handled as a separate cache miss and the cache line will be
refilled again into a different way, leading to two ways both being
valid for the same tag. This can lead to data corruption, in the
scenario where subsequent writes go to one of the ways and then that
way gets displaced but the other way doesn't. This bug could in
principle show up even without having multiple operations in flight in
the dcache.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This moves the logic for redirecting fetching and writing SRR0 and
SRR1 to writeback. The aim is that ultimately units other than
execute1 can send their interrupts to writeback along with their
instruction completions, so that there can be multiple instructions
in flight without needing execute1 to keep track of the address
of each outstanding instruction.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This changes the bypass path. Previously it went from after
execute1's output to after decode2's output. Now it goes from before
execute1's output register to before decode2's output register. The
reason is that the new path will be simpler to manage when there are
possibly multiple instructions in flight. This means that the
bypassing can be managed inside decode2 and control.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Michael Neuling
Paul Mackerras
Joel Stanley